Search Documents

A mechanised sub-level overhead benching method is used at Cleveland, to produce 22,000 tons per month of ore assaying 0.92% Sn and 0.40% Cu. The ore occurs in a series of vertical lenses which can be mined by open stoping. Levels are developed at 60ft., vertical intervals by jumbos. The ore is silled out and the stope block formed between levels drilled out by long hole drilling. Each row of holes is fired and broken ore within safe reach from the stope brow is mucked out by Wagner ST-5A Scoop Trams. The remaining broken ore is recovered on extraction of the next lower level. Ore is hauled by road to the crusher station from the mine. As mining proceeds below the lowest surface portal a spiral decline will be used for ore haulage and mine servicing.

Jan 1, 1970

By M Ziemski

The provision and management of energy in both fuel and electricity forms is an increasingly important consideration for mines. Pressures from communities, governments and markets are increasing towards more transparent and improved energy management. Combined with the energy-water nexus, where water and energy are closely related in the operation of a mine, this emerging business climate means a more thorough and responsible approach is required for the acquisition and use of energy, as well as the release of emissions. Many of the complexities in potential new ore bodies are borne in remote locations, high altitudes, low grades, arid climates and deep deposits. Each of these challenges affects the successful provision of energy. In combination, such challenges can leave an operation seemingly unviable from an energy perspective, especially when approached from a traditional mining energy feasibility lens. This paper discusses some of the energy alternatives currently available and emerging in the mining industry. Both energy supply and demand options are considered, which can provide a very different energy footprint with the flexibility to address, and potentially overcome, major energy challenges for a mine. CITATION: Ziemski, M, 2018. Energy complexities in complex orebodies, in Proceedings Complex Orebodies Conference 2018, pp 106–111 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A M. Sardo, D E. Sinnett

This study uses the Q Method to examine how those living in former metal mining landscapes value this heritage and their preferences for the long-term management of mine waste. Such sites are often perceived as derelict or degraded, and of very little value. It is therefore assumed that their reuse, for example for development or recovery of metals, is likely to be beneficial. There are around 5,000 former metal mines in England and Wales, many of which are protected for their ecological, geological or cultural value. The Q Method is particularly suitable for issues where there is no consensus of opinion. We asked 38 residents of six mining areas in England and Wales to ‘sort’ a series of statements based on their resonance with the resident’s perspective; this is the Q sort. The statements covered a range of opinions of the mining legacy, its value and options for its management with a particular focus on the potential for metal recovery from the wastes. Analysis of the Q sorts revealed five perspectives on the mining heritage. All placed a high value on the cultural and ecological value of this heritage, however, they differed in their priorities for long-term management. For example, emphasis was placed on either nature conservation, cultural heritage, water quality or the opportunity for job creation through reworking the mines. Cutting across these themes there were also differing perspectives on the role of experts and local people in shaping the future management of the wastes. This research suggests that the views of local people are nuanced; they value their mining heritage but opinion is split on the most effective way to manage these sites especially where there is an impact on water quality.CITATION:Sinnett, D E and Sardo, A M, 2018. Former metal mining areas in England and Wales – local residents’ preferences for the management of wastes, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 126–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By G Veillette, B Parker, S Hart

This paper provides a history of the challenges that were experienced while treating both the clayey oxide gold ores and the supergene copper-gold ores at the Boddington Gold Mine during the period 1989 to 2001. However the bigger challenge was to find a process flow sheet that would allow the economic treatment of the large low-grade competent gold-copper resource that underlies the oxide and supergene gold resource. Metallurgical test work and engineering studies on this resource started in the mid 1990s and culminated in the approval in 2006 of the 35 Mtpa Boddington Expansion Project to treat this material. The process flow sheet provides the basis of an energy efficient comminution circuit that includes high pressure grinding rolls and a treatment circuit with gravity separation, flash and conventional flotation to produce a precious metal low-grade copper concentrate followed by cyanide leaching of the rougher-scavenger and cleaner tailings streams. The treatment circuit allows maximum removal of copper minerals prior to cyanide leaching and so provides an environmentally responsible tailings disposal circuit.

Jan 1, 2007

Procedures employing thiocyanate and dithiol complexes of molybdenum have been developed for the determination of the metal in the presence of large quantities of ferric iron. The procedures are developed for field application and it is possible to complete 200 analyses per day with laboratory accuracy. Use is made of sulphuric acid extraction and ascorbic acid reduction in the case of the thiocyanate procedure whilst the reducing system in the dithiol procedure is potassium iodide-sodium sulphite. Using a simple photometer the range of determination possible is 0-10~g for the thiocyanate procedure and 0-5 g for dithioI.INTRODUCTIONOf the many colorimetric procedures that have been developed for the determination of molybdenum only those using the thiocyanate or toluene-3, 4-dithiol complexes of the metal are sufficiently free from interference to be of use in geochemical prospecting. Rapid methods based on both these complexes 'have been developed at the. Broken Hill Division of The University of New South Wales as part of a general programme designed to improve geochemical procedures. Whilst speed rather than high accuracy is the important factor in prospecting, the aim of the programme is to develop procedures which will allow determination of 200· samples per man-day without loss of normal laboratory accuracy for the methods concerned.In most geochemical procedures visual estimation of a coloured complex is used in the determination of the quantity of metal present. At the high rate of sample determination of the improved methods this procedure places severe strain on the eyes. For this reason all methods are designed for determination by means of a simple filter photometer...

Jan 1, 1965

WHEN mining and treatment first started at Broken Hill only oxidised ores were available. These ores were rich in silver and lead-the silver mainly existing as chloride and the lead as carbonate.Treatment processes aimed mainly at the recovery of silver, lead being regarded as a by-product, and its recovery, except in so far as it affected silver recovery, was of minor importance.The first ore mined was carted to Terowie and thence railed to Melbourne, being smelted by the Intercolonial Smelting and Refining Co., of Spotswood.The first parcel (50 tons) returned £7442, or £148 16s. per ton to the Broken Hill Proprietary Company.The second parcel of 1053 tons, smelted at the Day Dream smelter, returned 132,142 oz. of silver, but no record is available as to its lead content.These results obtained from two parcels showed that by smelting the ore a handsome profit could be obtained, and Mr. La Monte was engaged to erect two 30-ton Nevada water jacket blast furnaces on Block 13. These furnaces were placed in charge of Mr. P...

Jan 1, 1928

The distribution or the userul minerals or Tasmania is so closely connected with the geological structure of the island that it will be convenient to briefly recapitulate the principal ract or its geological history, before describing the ore and other deposits. In many cases these present features which are very puzzling in the absence of knowledge of the structure of the districts in which they are found and in all cases it is of benefit to mining engineers to be acquainted with the main facts of the geological·history of the regions in which they have to carry on operations. Moreover, in speculating as to the origin of lodes and other deposits, we have constantly to rerer to the crumplings or the earth's crust by mountain-making movements, and to the igneous rocks which have been thrust throngh the other strata, to explain the origin or the lode fissures, and this discussion cannot be carried on without knowledge of local geology.The oldest rock yet met with in Tasmania are of Archooan age, and consist of highly crystalline quartzites and micaceous schist. They are most extensively developed towards the western side ot the island, forming a belt parallel to the West Coast from South-West Cape to Cradle fountain; but they also crop out here and there to the west and northward of this belt, where the covering strata or later age have been denuded away. Though not seen in situ in the eastern part of the colony, the abundance or pebbles derived from this formation in the conglomerates of the coal measures shows that it must in those day have formed land surfaces there also, and makes it likely that the archooan strata exist at no great depth: below many of the beds of later age now occupying the surface. Lying unconfortably upon these highly metamorphic strata we find next an extensive series of subcrystalline metamorphic conglomerates, grits, sandstones, slates, and limestones,of Cambro-Silurian age. These are well seen in the Gordou River Basin, along the West Coast Range, aloug the North Coast, and in the goldfields of the north-eastern portion of the colony. They are much broken by later intrusive rocks, and covered by younger rormations, but the series is spread more or less over the whole island.

The object of this talk is to bring before members the importance of the prospector and the' State Battery system to the wealth and prosperity of the mining industry in particular and the State of Western Australia in general, and to touch on the more important features.Customs plants of any sort are usually subject to a good deal of critioism, usually on the large profits made at the expense of the customer, etc., and this often clouds the real value of the work being done.Prospectors, on the whole, are a good class of men; they work under conditions and difficulties which would deter those less spirited. Food, water and mining supplies are often difficult to obtain and frequently have to be transported great distances. Their mining tools are usually of the most primitive type, yet during last year over 109,000 tons of prospectors' ore were handled by the State Battery system for 73,250 fine oz. valued in Australian currency at over £587,000, the value being 57/- per long ton at par.This production brings the State Battery system into fourth position amongst the producers of the State, the yield being exceeded by the Lake View and Star, Wiluna and the Great Boulder.In passing I might mention that these notes were written at the end of the year 1940, and the above figures were for the previous period. The figures for last year, 1940, were not quite so good, being 101,000 tons for approximately 60,000 fine oz., valued in Australian currency at £572,000.In spite of this drop the State Battery system maintained its position as fourth in order of gold output for the State.The extractions, as a whole, throughout the system, were 92·54%, made up of 68·86% by amalgamation and 23·68% by cyanidation. These figures, for a group of 20 plants treating widely different classes of ore, must be considered satisfactory. The total production since inception is over £11,000,000 in Australian currency.State Batteries are usually more or less of a standard design. Ore is reduced to about 2i in. maximum size before being sent to the bins. Challenge automatic feeeders control the feed to each mill unit, amalgamated copper plates collect the free gold. Corduroy strakes are used with some ores after amalgamation, but in only a few cases has this been found of any advantage to the customer.The pulp from the battery is sampled, after leaving the tables, with a "Tazewell" sampler and pumped to dams for subsequent cyanide treatment.The "Tazewell" sampler is a machine driven by the moving pulp; and takes about fifteen dips per .minute from such pulp through a slotted...

Jan 1, 1941

The concept of a magnetic hydro-cyclone is undeveloped, possibly because studies by Bragard (1965) and the Royal School of Mines in London (Robinson, 1965) were not encouraging. Its role for the concentration of ironsands is attractive in that the classifying effect within a hydrocyclone may be comparable to the classifying effect in the gravity concentration of ironsands, and thus two steps may be achieved in one. Furthermore it should be a very simple and cheap process. The idea has been explored intermittently since 1976 but more energetically since the offering of a magnetic hydro-cyclone thickener by Boxmag Rapid (1983). This paper summarises the development and test work which are detailed elsewhere (Fricker, 1984).

Jan 1, 1984

About twelve months ago, owing to the increasing quantity of stone and dirt being drawn frQm the Victorian State Coal Mine due to the large amount of dead work below ground, cutting, faults, etc, and to the increasing quan#ty of banded coal beingworked, the writer was forced to consider the question of economy in handling the spoil at the surface. The method in operation at the time was to run out level dumps fro,m the, tipping floor of the heapstead, or brace, and to tip most of the skips of stone in tipplers at the ends of the dumps, the remainder of the skips being side-tipped to widen the dumps.The method, whilst quite satisfactory for dealing with a few skips of stone, was found to be costly as the dumps extended, and the number of skips to be dealt with increased from 300. to 400 per day of two shifts;. therefore, in order to expedite thework and cheapen its cost, the writer devised an improved method which may be qescribed as follows :-(1) The stone is tipped into a hopper car which holds about 10 skips(2) The hopper car is hauled up an inclined dump by means of an electric winch.(3) The spoil is dumped from the car forwards or to either side, as required.(4) The car is returned to the starting point for a further load.Plate I Fig. 1 gives an idea of the construction of the hopper car. In the illustration the car is in position for tipping to one side. The body of the car is supported on a ball race on the under carriage, and it can be swung round to tip in any required direction. The bottom of the hopper is extended to form a 4 ft. lip...

Jan 1, 1918

KIeeman (1968) described practice in the Mount Hebbard dump concentrator, Broken Hill, N.S.W. The purpose of this note is to give data on flotation pulp chemistry in the plant for comparison with results of Woodcock and Jones (1970a, 1970b).Ten chemical parameters were measured at ten points in the circuit using the techniques of Woodcock and Jones (1970a, 1970b). Fig. 1 shows a condensed time plot of some continuous measurements in conditioner overflow and rougher feed. Fig. 2 shows average values of selected parameters at the start and end of each of the three rougher flotation stages.DISCUSSIONpH and redox potentiaIsFig. 1 shows that pH and Eh were relatively constant at the start of sulphide lead flotation. There was a fairly steady increase in pH throughout the circuit (Fig. 2), but flotation was always conducted in a slightly acid pulp in spite of the large amount of alkaline reagents added. Eh values became more positive as the pulp progressed through the circuit (Fig. 2) in accord with results elsewhere.

Jan 1, 1973

The purpose of this paper is to cover in a general way the extent, geology, quality of product, working methods and trials of the coal mining industry. of New South Wales from 1946 to the present day, with particular reference to the Western field.It must be clearly understood that any opinions expressed are those of the author and not necessarily those of the Joint Coal Board.The extent of the Western coal field at the present stage of investigation may be said to be from a few miles east of Katoomha to a few miles north-west of the township of Ulan, the total distance being 150 miles.To the west of a line from the Western Highway from Lithgow through Wallerawang, PortIand, Tyldesley, Ben Bullen, Kandos and Rylstone, there are no signs of coal except for one or two outiiers in the neighbourhood of Portland. To the east of this line the coal-bearing areas extend to the seaboard approximately 80 miles to the east.GEOLOGY AND CHARACTERISTICS OF THE COAL SEAMSThe Western coal measures belong to the Upper or Newcastle series, which have been correlated with the Sciritheru or lllawarra, and the North-western or Gunnedah measures. Being close to the margin of the coal basin the Western measures have an average thickness of only 200 ft. to 500 ft., or approximately one-half of the maximum development of the Newcastle measures. They are underlain by Upper Marine beds which in turn rest directly on Devonian rocks.

Jan 1, 1954

The Misima open pit gold mine is a 20Mt per annum operation. Blasthole drilling is used to sample all material at a uniform 5m square pattern, and representative sub- sampling of the blast holes enables assay samples to be collected over the full 10m bench height. Samples are assayed for gold, silver and copper at the Company's laboratory at the mine site and the assays are provided to geologists as a written assay report and on floppy disc. Surveyed blasthole locations and assay results are transferred via personal computers (PCs) to a SUN mini-computer where results are stored by bench, blasthole assays are kriged, and plot files are created. A geologist selects grade boundaries from the kriged data, adjusting the boundaries towards the raw blasthole data where hard boundaries are recognised. Surveyors peg the resultant boundaries in the pit using a system of colour-coded pegs to display the different material types. A daily plan also shows boundaries and face positions.

Jan 1, 1991

By G Hart

As the iron ore/magnetite boom gains momentum, it is particularly important to question established past trends and explore the potential of alternative design options. Traditionally, ‘rule of thumb’ methods have been used to size dewatering equipment. Greater consideration needs to be given to technological advancements and specific throughput testing of each ore body type based on innovative developments.This paper will describe how an innovative approach resulted not only in significant savings in capital cost and site work hours but also delivered a truly optimised design for the thickener duty at Karara. Test work also played a crucial role and a comprehensive test work program on the ore samples showed the scale-up benefi ts of new technology in thickener designs. Working closely with the Karara team during the laboratory testing proved the old sizing theories for iron ore/magnetite processing have been superseded with the knowledge and results of the industry’s newest feedwell technology. Increased solids flux and rise rates in the testing process proved very successful, resulting in signifi cantly reduced thickener sizes and lower capital expense.Mechanical design considerations such as removal of underflow and pump access led to a preference for an above-ground thickener confi guration, and the economics of a completefabrication and installation package favoured steel construction for the thickener units.The ultimate choice of the bolted/fl anged tank methodology provides both economic and timely solutions for the site installation including reduced man power and quick and safe site-work. A benefits comparison between this design and other fabrication and installation procedures will also be analysed in the paper.

Jul 11, 2011

By L Avalos, F Melo Miranda, J Misle, M Ingwersen

"Los Pelambres, majority owned by the Chilean company Antofagasta Minerals, is one of the leading producers of copper and molybdenum in the country. It is located high in Andes Mountains, over 3000 metres above sea level, 316 km from the nation's capital, Santiago.The maintenance service supplied to Los Pelambres over the past 13 years has evolved to the point that FLSmidth now provides an integrated service crucial to the management of their customer's assets. The contract initially involved specialty mechanical, electrical and instrumentation maintenance and has developed to encompass maintenance planning and plant control systems.The integrated partnership has delivered excellent results in the areas of improved availability, reliability and return on investment. The operation is now amongst the industry leaders in plant availability.The integrated maintenance service has delivered: An increase in plant availability from 93%, in the first year, to 96.5% today, generating approximately $50 million additional income per year, Quality work procedures, Process and equipment improvements, Major shutdown planning involving more than 700 personnel, 6000 parts and over 2 000 discrete activities.The ongoing success of the partnership requires a high level of understanding between both companies. A commitment to maintain a long term sustainable relationship, based on a ""win - win"" culture, is the key to this success. In this regard Los Pelambres has been a pioneer in establishing and developing such relationships.This case study will share the lessons learnt, the measures taken to improve performance and the best practices adopted during the 13 year evolution of the maintenance service partnership.CITATION:Misle, J, Melo Miranda, F, Avalos, L and Ingwersen, M, 2013. Integrated maintenance services at the Los Pelambres Mine in Chile - The lessons learnt and best practices developed from a long-term sustainable relationship, in Proceedings MetPlant 2013 , pp 296-331 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By M Shaffer, D C. Grant, D J. Goudie, P Sylvester, C Voisey

Scanning electron microscope–Mineral Liberation Analyser SEM-MLA can be used to discriminate between hematite/magnetite in iron ores, but achieving backscattered electron (BSE) segmentation between the two minerals is difficult for particles =75 µm using typical preparation and analysis methods for the MLA based on a tungsten filament SEM (Quanta 400) with 25 kV high voltage. Preparing iron ore sample mounts using a slow-speed polishing method, and conducting the experiment on a field emission gun SEM-MLA (Quanta 650) with the high voltage (HV) setting lowered to 15 kV reduces instrument noise and results in very clean BSE images and segmentation. This method requires new X-ray standards to be acquired for each mineral identity at 15 kV because of major changes in the spectra at lower kV. However, once these X-rays are added to the mineral reference list, effective segmentation can be achieved and a proper analysis obtained.CITATION:Grant, D C, Goudie, D J, Voisey, C, Shaffer, M and Sylvester, P, 2017. Discriminating hematite/magnetite via scanning electron microscope–mineral liberation analyser in the - mesh size fraction of iron ores, in Proceedings Iron Ore 2017, pp 541–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By M Andrew, D McTiffen, M Adams

A major Ventilation Upgrade Project commenced at the Fosterville Gold Mine (FGM) in 2017 to service the ongoing ventilation requirements of the underground mining operation. The project consists of three large diameter ventilation raises totalling 1100 metres, and new axial primary ventilation fans to upgrade the mine ventilation system. With a mining depth of 1200 metres and a thermal gradient of approximately 2.7 °C per 100 metres of depth, the completion of the Ventilation Upgrade Project is key to the ongoing success at FGM. The Ventilation Upgrade Project will allow continued mining, including high-grade gold deposits, lower in the mine where heat is increasing. Figure 1 below illustrates the underground workings at FGM, and provides a general view of the ventilation upgrade works to establish the new exhaust system from the lower workings to surface. Whilst raisebore pilot drilling the H4760 Return Air Rise (RAR) from surface to 395 metres, the raisebore drill string became stuck in the raisebore pilot hole at approximately 300 metres down hole, presenting a significant technical problem and delays to the project. This Case Study provides an overview of the recovery process undertaken at FGM including the recovery of the stuck drill string. The value of the stuck in-hole equipment, the investment in the shaft site preparation, the collar stabilisation, the underground development to the base of the ventilation raise, the surface footprint prepared for the Primary Fans construction and the limited available space on the site were all motivations to recover the raisebore drill sting and ultimately recover the ventilation raise location. More importantly, the long lead-time required should a new shaft location be the final solution, and the delay this would incur to the ventilation upgrade was unacceptable. Recovery of the drill string was not possible using the capability of the Contractor’s Raise Drill. An alternative method for freeing the drill string was required. A significant amount of engagement with industry was undertaken to seek out potential solutions and draw from the experience of others. All methodologies available were considered and assessed. Ultimately, after several attempts at freeing the raisebore drill string using various methodologies, Adams Drillers and Clear Cut Interventions were engaged to provide a turnkey recovery solution.

Mar 15, 2021

The mineral composition and microtextures of a cubanite-rich sulphide ore are described and cubanite breakdown textures are illustrated. The occurrence of cubanite in macroscopic dimensions is featured.The origin of the ore is tentatively related to a composite ore fluid arising initially from an ultramalic source and extracting some metal components from an older granite mass along the margin of which the serpentine was emplaced. Some alternative possibilities as to origin are also mentioned.

Jan 1, 1969

The Australian Gas Light. Company was established in 1837, the first gas being sent out from the Kent Street Works, then the headquarters, in 1841. Mortlake Works were opened in 1886, and has since grown to the vast undertaking inspected by members of the Institute.The Kent Street Works were closed in 1921. The area of the, company's property at Mortlake is 117 acres.Some interesting figures from the statistics of the company's activities for 1937 are:-

Jan 1, 1938

Sphalerites from Devonian cassiterite-sulphide deposits and Pb-Zn-Ag fissure veins have similar ranges of Cd contents, but the average Cd and Fe contents could indicate a small initial difference in availability of Cd between the Zeehan-Renison Bell district and the Mt. Bischoff-Waratah district. Sphalerites from banded Pb-Zn deposits (Rosebery and Hercules) are characterized by low Cd content which is a world-wide feature of such deposits in exIrusive rocks, and may indicaIe a genetic relationship between ore deposition and vulcanism.

Jan 1, 1968