Search Documents

By Warner RE

SINCE 1952, when Elliott et a/ first applied the Sherwood correlation for flooding in chemical absorption towers to blast furnaces numerous investigators throughout the world have followed their example and much research effort has been spent to tighten the correlation and recently to extend investigation of flooding to side gas entry conditions. The widespread use of the Sherwood concept of flooding has been such that even the word itself has become an integral part of blast furnace nomenclature. The evidence for the applicability of Sherwood's relationship has been that the flooding limits calculated from blast furnace parameters lie approximately on the Sherwood line. However, the values of many of the variables for the blast furnace calculation are only estimates and at first sight one may wonder at such 'close' coincidence when some of the estimated parameters entering the Sherwood correlation are raised to the power of three or more, as for the bed porosity and the liquid surface tension. It is felt that the explanation of this result lies in the logarithmic: nature of the plot and/or the fortuitous can- cellation of the errors of the estimates in the calculations coupled with the fact that blast furnace fluid ratios lie within a very narrow range of values. The foregoing considerations should in their own right place doubt on the correctness of the Sherwood type flooding correlation applied to the blast furnace. Additional doubt regarding the existence of the Sherwood type flooding in the furnace has been cast by the results obtained in the Tokyo University experimental blast furnace. From the reasoning of both Standish and Colquhoun (p. 20) and Warner (p. 23) it is deduced that flooding in the traditional sense will only normally occur in the upper bosh (somewhere near the mantle), following softening as discussed by Palella et a/ on p. 75, and flooding in that zone is likely to result in furnace irregularity. On the other hand, the concept developed by Warner of slag hold-up above the raceways as a stable phenomenon not affecting furnace regularity is a process unique to the blast furnace and is not described by the Sherwood flooding theory. Recognising the considerable practical implications of slag hold-up above the raceways, this note further explores the physical process of slag hold-up. We envisage that bed of coke above the raceways in almost all blast furnaces would contain some slag held up by the gas pressure gradient. In general the slag would be contained in a ring and gas would bubble through in its ascent through the furnace. The force supporting this slag is the pressure gradient and obviously -much of the blast pressure is dissipated in supporting this structure.

Jan 1, 1975

The bureaucracy in Victoria has worked against exploration and mining development. There is no doubt that the new Mineral Resources development Act has simplified matters on the mining side of the system. However, WMC's Bendigo and Deep Lead experiences demonstrate that other parts of the bureaucracy can cause serious delays. The mining industry continues to view the approval process causal of excessive costs and delays compared with other States (and countries) and prohibitive to investment in Victoria.

Jan 1, 1992

THE MORWELL BROWN COAL DEPOSITSTHIS deposits of brown coal in the neighbourhood of Morwell, are of tertiary age, and are represented on several horizons, but, owing to lack of evidence, the exact age cannot be fixed definitely. It is chiefly by reference to the basalt flows of the Older Volcanic series that the brown coal beds have been classified as of Pre-Volcanic and of Post-Volcanic age. The Pre-Volcanic brown coals are less widely distributed, and the seams generally are thin, though near Thorpdale a thickness of 40 tt. has been recorded, and from 10 ft. to 12 ft. in the vicinity of Narracan. Both of these localities lie to the south-west of Yallourn, and it has not been proven as yet whether these older coals and accompanying basaltic flows pass under the Morwell beds.The brown coal deposits have accumulated in an area where extensive faulting in early tertiary times has taken place with oscillations of elevation and depression of the land surface. In the vicinity of Yallourn, Paheozoic strata (probably Silurian) are exposed on either bank of the Latrobe River about a mile above the powerhouse weir, where the river flows through steep banks rising a couple of hundred feet on either side. The Silurian strata are highly inclined, and consist mostly of slates and Illudstones. Resting unconformably on the upturned edges of the Silurian is a conglomerate bed of Mesozoic age, above which occur beds clipping to the south-east of felspathic sandstones, with alternating mudstones at times carbonaceous, and containing thin seams of black coal.The brown coal seams and associated lignitic Clays, sands, gravels, etc, rest on the Mesozoic strata (as proved in the vicinity of the power-house and by boring north of the Latrobe River, near the old open cut), but do not appear on the surface of the Mesozoic, where these beds attain an altitude of more than 50 ft. above the present level of the Latrobe River.Half a mile upstream from the power-house a layer of basalt of the Older Volcanic series, almost resting upon the Silurian strata, is...

Jan 1, 1924

It has become increasingly clear in recent years that human kind has developed the capacity to alter the environment of the Earth on a global scale. The changes are often subtle. This is particularly true in the case of stratospheric ozone. Ozone is produced primarily in the stratosphere, at altitudes in excess of 20 km, initially through the action of ultraviolet sunlight dissociating molecular oxygen. According to theory as it existed up to a few years ago, ozone is removed mainly by reaction with atomic oxygen. In the unperturbed environment, this reaction proceeds both directly, and by paths catalyzed by trace quantities of nitrogen radicals. Molina and Rowland [Nature, 249, 810, 1974] pointed out that decomposition of industrial chloroflurocarbons could in-troduce an additional source of radicals to the strato-sphere. Chlorine radicals are even more efficient than nitrogen in catalyzing recombination of oxygen atoms with ozone; models suggested that we might expect reductions in the vertical column density of ozone of as much as a few per cent over the next several decades. A reduction in ozone of x¦/a, by increasing the flux of ultraviolet sunlight reaching the surface, was predicted to result in an increase of about 2x% in the number of cases of skin cancer, with other less well defined impacts on the non-human environment for life.

Jan 1, 1990

By C Rees, M Predebon, J Denney

It has been said on many occasions that æthe future of the mining industry of Australia, and indeed the world, lies in the hands of the studentsÆ. As a student, this can be a daunting, yet very exciting, statement. If nothing else, it is a direct challenge to the student body of the mining industry to take responsibility for its direction æafter 2000Æ. However, for the students to embrace this challenge, some responsibility must be borne by the universities and the industry itself to provide some direction and encouragement. Perhaps, therefore, the real challenge is to find the right balance between students, industry and education to best prepare the students for a career in the mining industry. The future industry will demand students who are capable and willing to adapt to change and technology and able to exert the vision and leadership required to ensure the mining industry continues to thrive well into the next century.

Jan 1, 2000

By Jiaxin Zhou

Acid mine drainage is a serious and chronic environmental problem of mining. This paper discusses the factors affecting the rate of acid generation by mine rocks and illustrates the relevance of these factors to the mines of the Northern Territory, Australia. The factors may be divided into two groups: internal factors and external factors. The first group covers characteristics of ores, mine waste rocks, tailings, etc and the second group covers surrounding conditions. The latter is further divided into four sub-groups, viz surrounding temperature and pressure, chemical conditions (ferrous/ferric adsorption ratio, total iron concentration, oxygen concentration and pH), surrounding biological conditions and mechanical conditions. Special attention is given to the surrounding P-T conditions, especially water partial pressure, and its relevance to the Northern Territory mines.

Jan 1, 1994

The Loy Yang Overburden System initially consists of a 60 000 tonne/day Bucket Wheel Excavator (BWE) (No. 14), a 2 m wide Conveyor System and a Travelling Stacker (No. TS4). The paper discusses details of the plant and the influence the soft clay overburden has on the design of the plant, to handle the dif- ficult Latrobe Valley overburden.

Jan 1, 1982

Natural gas from the south west Queensland gas fields is now available in north west Queensland to fuel the development of many Carpentaria Mineral Province projects. Like these projects, the south west Queensland gas project, developed under the operatorship of Santos Ltd, has its own æMining CycleÆ. While the project is entering its third expansion phase, it is at the same time actively extending its discovery phase, with large programs of gas exploration and reserves definition. This paper outlines the history of the south west Queensland gas project, with particular emphasis on the relationship of the project to north west Queensland.

Jan 1, 1998

By Roach C

Exploration on the Callide Coalfield by Thiess Bros. Pty. Limited had reached the stage in mid 1976 where there was a need for a comprehensive appraisal of the coalfield geology. Exploration strategy in 1977 - 1978 was defined by the selection of the most attractive targets. All available literature, reports and plans were reviewed and borehole records assessed. The geology of the coalfield was placed in its regional setting and the genesis of the Callide Coal Measures described in a structural and sedimentological context. Their general form and extent was then examined by the technique of stratigraphic analysis through the interpolation and extrapolation of the available data. A "localized" reserve classification was drawn up and reasonable estimates of the various geological reserves produced, in terms of their reliability and depth of overburden. Quality trend maps were also produced. The resultant "base map" was virtually a summation of all the information to June, 1977, and the basis for the exploration programme in the 1977 - 1978 financial year. The technique allowed for "base maps" to be produced at almost any stage, each one a refinement of its Predecessor.

Jan 1, 1978

This paper examines the operational characteristics and requirements of crushers and screens. Several possible control loops are considered and it is shown how these can be used to satisfy particular requirements.

Jan 1, 1978

Successful restoration of Ballarat region alluvial gold workings to Box-Ironbark forest requires realistic evaluation of techniques. A stocking level threshold of 68 percent is used to rate the success of 'broadcast' seeding of E. microcarpa, E. Melliodora and E. Leucoxylon.Failure necessitates follow-up enrichment planting with tubestock, which is considered undesirable, interalia, due to pathogen, spacing and economic problems.

Jan 1, 1992

By J J. Cilliers, K Hadler, A W. Stra

This paper examines the use of the FrothSim flotation simulator to improve the performance of an industrial column flotation cell. The performance of an industrial retreat column cell is simulated, and, from the discrepancies between the simulated and experimental results, a problem with the wash water distribution is postulated. The scientific reason for the reduced performance with uneven wash water addition is described in detail. Further simulations indicated the potential for improvement with an even wash water distribution, resulting in both improved performance and reduced wash water usage. The simulated uneven wash water distribution was confirmed industrially, and the headers were redesigned and installed. A sampling campaign to compare the performance before and after the modifications showed that the flotation performance was improved dramatically, with a statistically significant decrease in gangue recovery, without a commensurate reduction in valuable mineral recovery.

Jan 1, 2005

By Tomlinson R. C

There are two main aspects of coal preparation to which the operational Research Executive of the National Coal Board has applied computer models. The first is in the planning of preparation plants and the first part of this paper discusses Simprep, a computer package that was designed to help on these calculations. The other is the development of control schemes to improve quality control, and the second part of the paper deals with the development of simulation techniques for this purpose.

Jan 1, 1977

By Giannini L. M

Optimisation techniques, based on the block model, for solving the optimum pit limit problem were discussed in an earlier paper. Of the available techniques the one based on graph theory proved to be the most attractive. In the graph theory model the vertices represent blocks and the arcs represent the mining restrictions. For large ore-bodies direct application of the graph theory method poses considerable computational and storage problems. Techniques for easing the computational effort by reducingthe problem size were introduced in an earlier paper. Further, significant computational savings can be made by exploiting the structure of the graph. This is done by building the graph up level by level and successively applying the graph theory algorithm to reduce the number of blocks. In building up the graph in this way one needs what is called a "search pattern" to indicate which arcs are to be added as new vertices are introduced. Moreover, as it is essential to keep the number of arcs to a minimum it is necessary to establish a "minimum search pattern".The problem of determining minimum search patterns for any block model and for any wall slope restrictions has not been considered in the literature.The objective of this paper is to present a complete solution to this problem and to discuss, through typical case studies, the application of the associated software developed.

Jan 1, 1988

The Hunter Fracture Zone can be traced into the Fiji group, and onshore SE Viti Levu in the form of NE-trending morphostructures. NW- trending morphostructures offset the NE elements. Structural mapping of Suva Harbour indicates that the NE elements are grabens bordered by faulted monoclines. Faulting is characterised by block-rotations and dip-slip displacements. The NW morphostructures are faults displaying elements of both dip-slip and strike-slip movement. Structural overprinting suggests that the NW faults represent the youngest phase of deformation, and current seismic activity occurs on this trend. A conceptual, geomechanical model of the deformation invokes toppling and wedge failure at the edge of the Fiji platform, translating material downslope into the Hunter Fracture Zone. The interference pattern produced by the superposition of the NW on the NE structures consists of a series of circular features bearing superficial resemblance to volcanic centres. Known mineral deposits in SE Viti Levu correspond closely to these features. The formation of the circular features postdates mineral genesis, suggesting that the features provide a focus for the enhanced exposure of mineral deposits rather than a source of mineralisation. There is a close association between mineralised exposures and interference patterns in extensional structures in SE Viti Levu, and a correlation between these structures onshore, and the Hunter Fracture Zone cum South New Hebrides Trench offshore. Future mineral exploration in the SW Pacific will benefit by closer consideration of the geologic structure of Pacific islands bordering the extensional regimes of deep oceanic trenches.

Jan 1, 1987

This paper is essentially an address, rather than a detailed presentation of facts, because the third edition of `Nuclear Electricity - An Australian Perspective' has just been completed and will be available for the seminar. That 96-page booklet contains a lot more information than The AusIMM would be prepared to print in the seminar proceedings. Hence I have kept this paper brief, and ask readers to obtain a (free) copy of Nuclear Electricity at the seminar or from The AusIMM. It can be read as a supplement to the paper (or vice versa). According to one of Australia's well known critics of nuclear power, Professor Ian Lowe, `the pro-nuclear lobby's predictions of the future use of nuclear energy .... have been regularly and consistently wrong by large amounts, always overestimating the future demand for uranium" (Aust. Society, April 1989). While I do not accept this as a bald statement applying to all those in favour of increased use of nuclear power, there is sufficient truth in it for it to be credible. Certainly in the 1950s and the 1960s, when the new technology for producing controlled power from atomic fission was first being commercialised, there were some very exaggerated projections of the role of nuclear power. Many people thought that it would take over from fossil fuel fired electricity generation in much the same way as the motor vehicle took over from horse-drawn transport. And these early projections were not simply concerned with electric power generation, they included excavating harbours and digging canals with nuclear explosives.

Jan 1, 1989

By Burgess J, Brownrigg A

The world steel industry underwent rapid growth from 1950 to 1970. Since that time, production growth has been relatively slow, with declining production in the developed countries and increasing production in some newly developing countries. Since 1970, Western World crude steel production has been static at around 450 million tonnes, with cycles around this level in a 100 million tonnes band.

Jan 1, 1992

At the outset I want to thank you for inviting a representative of the Chamber of Mines of South Africa to address you on the subject of mining and its future at this, the 13th Congress of the Council of Mining and Metallurgical Institutions. It is indeed a pleasure and an honour to be here. As many of you will recall, four years ago I, as the then President of the South African Institute of Mining and Metallurgy, had the privilege of hosting and welcoming you to the 12th Congress, the third such congress hosted by South Africa. The late Sir Ernest Oppenheimer, President of the 1930 Congress - the first to be held in South Africa - in his opening address foresaw the mining industry as "the most potent factor in spreading the benefits of civilisation over the sub-continent." We have come a long way since those halcyon days but, as I noted four years ago, it still remains true that mines have been, and will continue to be, the missionaries of development in many, if not most, of the Third World countries. I have been asked to address you on the subject of "mining" and to let my imagination roam widely so that delegates can leave the congress with a broader vision than they brought on arrival. It is a tall order and in my attempt to fulfil it I ask you to cast your minds back 120 years to a sultry, rustic day when the first diamond was discovered in South Africa at the now famous town of Kimberley. At that time the South African economy, predominantly pastoral, was still at subsistence level. Almost overnight the ensuing diamond rush turned the then British- owned northern Cape Colony's semi-desert scene into a hive of mining activity, every prospector bent on making his instant fortune. It was very little different, I am sure, to the gold rushes that hit California in 18+8, Australia in 1851, New Zealand in the 1860s. and the Yukon in the 1890s.

Jan 1, 1986

By Kerr M. H, Slaughter P. J

Design of the new cemented hydraulic fill plant was based mainly on experience with a succession of previous fill plants. Two stage cycloning of combined concentrator tailings was introduced. Design of the two stage cyclone configuration was assisted by computer simulation of cyclone performance. Cementing additives, namely Portland cement and ground copper reverberatory furnace slag, drawn from bulk storage, are pre-slurried prior to mixing with hydraulic fill. Quality control of fill being sent under- ground is achieved by a series of automatic control loops. Plant instrumentation was given prime consideration during the design phase. Inventory checks of all mass flow metering equipment are made at regular intervals. Fill is pumped to boreholes at several locations. Details of the equipment and operating procedures for the plant are Discussed.

Jan 1, 1973

By R Brake

The Enterprise Mine Project (EMP) is being developed by Mount IsaMines Limited as the future source of copper ore at the Mt Isa miningand processing complex. Environmental engineering is one of the majortechnical challenges facing the project because of the depth of theorebodies, high virgin rock temperatures and hot ambient surfacetemperatures in summer. This paper discusses the engineering principles adopted by EMP to manage the risks associated with working in these adverse thermal conditions.

Jan 1, 1998