Search Documents

By Z Li, Z Yan, M Yang

Recycled cement paste (RCP) is a kind of CaO-rich recourse, which is separated and recycled from waste concrete. Due to its chemical composition, RCP could partially replace lime as a flux and be loaded into electric arc furnace (EAF) steelmaking process. Rapid RCP assimilation and liquid slag formation have significant effects on EAF steelmaking process. In this study, the dissolution behaviours of RCP and lime at temperatures of 1400°C to 1500°C were investigated using static dissolution experiment. The dissolution rate, interfacial microstructure, as well as dissolution mechanisms were discussed. It was found that the dissolution rate of RCP was much higher than that of lime. RCP could be completely dissolved into slag in 60 secs at 1500°C. The dissolution rate of lime was in range of 3.910-4 g/(cm2ꞏs) to 2.610-3 g/(cm2ꞏs), while that for RCP was in range of 1.510-3 g/(cm2ꞏs) to 4.910-3 g/(cm2ꞏs). As for lime dissolution, a dense layer of dicalcium silicate (C2S) generated at the dissolution interface, and the diffusion of Ca2+ in C2S layer was the limited step for lime dissolution. Some of calcium ferrite could be observed at the interface between lime and C2S layer. As for the RCP dissolution, there is no obvious product layer of C2S formed at the dissolution interface, Fe2+ continuously diffused into RCP layer during the dissolution, and small amount of FeOꞏMgO solid solution generated and gathered at the dissolution interface. The dissolution rate of RCP in EAF slag was quite higher than that of lime, partially add RCP as flux in EAF could accelerate the slag formation process.

Aug 21, 2024

By P R. Botha

Mining has played a significant role in human development and without the mining sector, society would not enjoy a large number of the benefits that it does today. However, mining has also carried with it some important lessons, which remain the source of ongoing learning. One of these lessons is the poor closure or abandonment of mines, worldwide. This has in many cases resulted in large tracts of unproductive land, representing a source of environmental pollution and a safety hazard to the community. Frequently associated with this is a legacy of mining communities having fallen into economic and social decline, beyond mine closure.Due to this legacy, governments, society and the mining sector pay far greater attention to mine closure planning today, than was done in the past. Typically closure planning has focused on the engineering aspects of a mine, namely decommissioning of the workings and plant; dismantling of unusable infrastructure; and rehabilitation of disturbed land. These are important aspects of closure but a more holistic, long-term approach is required which encompasses environmental and social aspects and aims to leave a positive legacy behind.In planning for a mine closure scenario with a lasting positive legacy, it is critical that the broader receiving environments (social, economic, physical and biological) within which a mine is located, define and drive the closure plan and the mine planning as a whole. This ensures that the broader environment influences mine closure, as opposed to looking at how a closed mine will impact on the environment. The ultimate aim is to first understand the broader environment and then to fit the closure of a mine into it. The earlier this approach is followed in the life of a mine, the greater the operational time frame available, and hence a better chance is presented for planning and managing a mine towards the desired, tested and agreed post closure scenario. Within this broad context, there is tremendous scope to achieve successful mine closure. However, it is critical to note that mine closure is not the sole responsibility of the mining companies, and neither is it possible for said mining companies to achieve mining closure alone. This concerted effort requires a multi-stakeholder approach in which partnerships are created and risks, responsibilities and opportunities are shared and managed. To achieve sustainable closure, a multi-stakeholder approach based on an initial forward-looking closure vision is required. This approach provides an early basis for consideration of alternative land uses and economic options from which specific actions to achieve the preferred option can be defined. The Anglo American plc Mine Closure Toolbox has been formulated and developed around this concept. The Toolbox aims to expand mine closure planning - from financial provisioning for rehabilitation and physical closure, to planning for sustainability beyond mine closure and leaving behind a positive legacy.This paper focuses on the business case for mine closure planning and provides an overview of the Anglo American plc (AAplc) Mine Closure Toolbox.CITATION:Botha, P R, 2012. The business case for mine closure planning and an overview of Anglo AmericanÆs mine closure toolbox approach, in Proceedings Life-of-Mine 2012 , pp 7-10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Tonks E. E

The earliest discovery and mining of coal in the northern area of the Greta Coal Measures at Anvil Creek in 1862 was by William Farthing, however, some official records attribute the discovery to Thomas Frost in 1864. Frost's discovery was examined by William Keen, government examiner of coalfields, and further prospecting was carried out. This was followed by the pioneering work of C S Wilkinson, government geologist in 1884. Subsequently in 1886 C S Wilkinson entrusted a detailed survey of the coalfield to the then geological surveyor, T W Edgeworth David.The outcrop of the Greta Coal Measures around the Lochinvar dome was mapped by Edgeworth David and as soon as he reported his discovery, the Department of Mines reserved in the interests of coal mining an area of 23700 acres, which extended between what became the South Greta and Abermain No I Collieries.

Jan 1, 1993

Madison Enterprises Corp. and Matu Mining are currently ex- ploring the Mt. Kare property in Papua New Guinea. The Mt. Kare gold prospect has had a short but very active history, since the first discovery of gold in the area in 1986 the property has sccn: a 3 year gold rush during which 10,000 alluvial miners re

Jan 1, 1997

By Choulaj D

Mining and petroleum continue to be the two most vita components of our nation's development, says Sir Julius Char in the Australian Journal of Mining (Nov-Dec 1996). In fact the} account for 71.6% of export earnings, and 21.2% of Gros; Domestic Product in Papua New Guinea. The Misima and Porger, Mines, along with the Kutubu oil project, have essentially rescues PNG's economic viability since the loss of income from Panguna Though the industry cannot create employment in the manner o. intensive industries such as agriculture, it does provid( opportunities to local communities in terms of jobs, financia compensation, and infrastructure. Many ventures take many years and enormous capital investment to set up. There are three phases: exploration, feasibility, an( operations. The operations phase sees a massive development o infrastructure, or the actual `building' of the mine. For mining companies to commit to such lengthy time frames and high level: of investment, without returns, requires confidence and a degree of commitment from government on a number of levels - legislative stability, monitoring social development, and the provision o social infrastructure.

Jan 1, 1997

Reconciliation involves the collection of tonnage, grade (quality) and contained metal (product) data from disparate and hopefully independent sources. Examples are exploration data, production sampling data from blastholes or drawpoints, and process plant data. These data may be compared by means of ratios (factors). The F1 factor usually relates short-term (ore control) model tonnages, grades and metal content to ore reserves depleted. The F2 factor usually relates received-at-mill tonnages, grades and metal content to delivered-to-mill = production tonnages, grade and metal content. The F3 factor is F1 × F2 and enables a comparison of a mineÆs ability to recover the tonnage, grade and metal content estimated in ore reserves. The F1 factor measures the accuracy of orebody knowledge in the ore reserves to the demarcation of ore and waste by ore control (short-term model). The F1 factor may be used to check and calibrate the selectivity of mineral resource models and/or planned dilution assumed in transfer from mineral resources to ore reserves. The F2 factor enables a check on unplanned dilution entering the ore stream between ore control and the mill. Using the factors it is possible to calculate a monetary value on improvements in the accuracy of orebody knowledge, selectivity and the effects of dilution and ore loss. Reconciliation should be an implicit part of the mining process, and reconciliation targets should be a key performance indicator for well-run mines.

Sep 26, 2011

Knowledge of coalfield geology has evolved rapidly over the past few years. Recent advances ranging between exploration, mining geology and seam variation studies have enabled application of geological techniques commensurate with technological changes in the coal industry.

Jan 1, 1969

By Weller KR, Restarick CJ, Stewart PSB

Following a detailed assessment of concen trator performance at Broken Hill South Limited which was reported in a previous paper, the fine grinding section was changed from a parallel arrangement of the two grinding circuits to a series arrangement, and the concentrator per- formance re-assessed. The change to series grinding had virtually no effect on the actual or potential capacity of the circuit to make a final product with 80% passing 100 mesh. However, the fresh flotation feed contained significantly less +150 mesh lead and +65 mesh zinc (material which was shown to float poorly), without an increase in the quantity of poor-floating ultra-fine lead and zinc. From the size-by-size flotation recovery data, it was shown that overall recoveries of both lead and zinc were approximately 1% higher than they would have been without this change in size distribution and it was concluded that this was a direct result of the change in grind- ing procedure.

Jan 1, 1972

By T Baumgartl, A Costine, B Boshrouyeh, M Edraki

In mineral processing, the management of tailings may become increasingly more challenging with a change of ore type and the quality of water used in the plant. This, in turn, may affect the overall costs of the operation and water usage and, in the long-term, pose challenges for mine closure and rehabilitation. Depending on the applied treatment technique, the short and long-term properties of tailings are largely determined by the fine particles. Most clay materials and ultrafine particles exist in tailings from oil sands, coalmines and base metals, bringing about challenges in dewatering performance. Moreover, given the growing concern for water scarcity, the minerals industry is increasingly turning towards the use of saline water, which poses yet another challenge for tailings management. The high salt content alters the behaviour of clay particles, making dewatering a more complex process than in freshwater systems (Boshrouyeh Ghandashtani et al, 2022; Costine et al, 2018). High-density techniques for tailings management have been used for several years in the mineral industry. In this regard, one of the novel and promising dewatering methods is in-pipe or inline flocculation, where the polymer is added at high dosages to thickener underflows, giving additional (likely denser) aggregation, releasing more water on deposition compared to low solids thickening. Previous research in the field of flocculation has primarily focused on the process of flocculation itself, specifically the settling rate and size of aggregates, rather than the long-term impacts of the produced tailings materials (Liu et al, 2020; Jeldres et al, 2017). This is particularly true for the novel method of this technology, where polymer is added to the thickener underflow. Furthermore, these studies have used small-scale set-ups using buckets/beakers, plungers and mechanical stirrers for the flocculation process. Unfortunately, these methods lack the necessary control over the properties of the treated tailings, which can lead to irreproducible mixing and dispersion of viscous polymer solutions (Fawell, Costine and Grabsch, 2015). Consequently, a system that can work with a wide range of operational conditions for high-solid tailings material is essential for reliable and reproducible results. The objectives of this study were to determine the effect of different type of polymers in the presence of monovalent and divalent salts on the inline flocculation of artificial tailings. The next step was to evaluate the impact of high-dosage polymer addition on geotechnical properties such as settling rate, consolidated density, rate of consolidation and the hydraulic conductivity of tailings. In addition, this research aimed to fill a knowledge gap and investigate the feasibility of using polymer-treated tailing in removing the copper ions and then quantify the performance of produced aggregates under time-dependent processes.

Aug 2, 2023

By B Walker, A Robertson, C Wels, S Fortin

A background characterisation study was carried out in the Sangre de Cristo mountains, New Mexico, to: quantify naturally occurring contaminant loads from mineralised areas; define site-specific background concentrations; and to determine key factors controlling spatial and temporal variations in contaminant concentrations. The study included a comprehensive sampling and testing program (paste pH/EC, ABA, leach extraction tests) of soil/bedrock from mineralised areas (including erosional scars), and a ground water and surface water quality monitoring program in selected mineralised watersheds. Results demonstrate that high concentrations of contaminants occur naturally in ground and surface water draining the mineralised area of the Red River basin. The erosional scars were found to represent the major source of acid rock drainage (ARD) (~66 per cent) in this area due to: high rates of weathering and erosion, which continually exposes sulfide-bearing outcrops; and high rates of run-off as a result of high elevation and lack of vegetation. The scar material is generally very acidic (paste pH ranges from 8.5 to 1.5; average = 3.6) with highly elevated concentrations of sulfate and leachable metals. The composition and concentration of leachable metals vary significantly, not only between scars but also within a given scar. While all streams draining the various scar watersheds are highly acidic, each has a characteristic æfingerprintÆ of sulfate and metal concentrations. Most of the run-off from the scars infiltrates into alluvial debris flow aprons and reaches the Red River via groundwater flow.

Jan 1, 2003

By Tooley S. M

An experimental investigation of the hydraulic cuttability of coal from the Theiss Dampier Mitsui mine near Moura, Central Queen land illustrated the ability of established cutting equations to describe the behaviour of the coal during cutting. The experimental equipment developed for the work proved reliable. The results of the experimental programme are consistent with accumulated experience from overseas.

Jan 1, 1985

By L Hussey

Mt Keith concentrator treats low grade disseminated nickel sulfide ore supplied from the adjoining open pit mine. It is a traditional crushing, two-staged closed circuit grinding circuit (SAG & Ball Mills), followed by a complex split-size rougher, scavenger and cleaner flotation circuit. In 2016, 10.5 Mt was milled, at an average head grade of 0.54% Ni, yielding 35 000 nickel metal tonnes in concentrate.Historical analysis of the plant data indicated that of all the nickel lost in the fines rougher circuit tails stream, 25.6% was recoverable in an eight minute laboratory scale flotation test. These results implied that this fine nickel was readily available for recovery in the plant, either through operational improvements or additional flotation capacity. With operation optimisation ongoing, and capital within the business focused elsewhere, plant personnel were challenged to think differently about improving recovery.In 2012, a separate project to improve plant recovery when treating high talc ore was completed. Amongst other vessels, this project saw the installation of two 150 m3 Outotec Cells to the scavenger section of the fines rougher, middlings and scavengers (RMS 1) circuit. Since installation, the operation of these cells resulted in difficulties immediately upstream with instability in the scavenger cells. It was therefore decided that these cells would be better suited to treating the fines rougher circuit tails.The alterations required to divert these flows were minimal, with the capital project totalling $220 000.In the two years since installation, the fines rougher tailings nickel grade has dropped by 9.9%. The scavenger circuit has also seen a 2.8% reduction in tailings nickel grade, and instability issues were immediately resolved. This project serves as a lesson in how existing plant infrastructure may be better utilised to maximise recovery. Although this is especially applicable when capital constrained, such re-appropriation can be considered at any point to maximise return on existing assets. CITATION:Hussey, L, 2017. Repurposing flotation capacity at Mt Keith nickel concentrator, in Proceedings MetPlant 2017, pp 254–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

The rocks of the Serranias Chilla massif of Bolivia are a suite of metamorphosed Palaeozoic basalts and associated continental sediments. Whole-rock trace element geochemistry of the basalts suggest a calc-alkaline affinity and indicate that subduction extended as far north as the Bolivian Altiplano during lower Palaeozoic time.

Jan 1, 1990

All large open pits in Australia have been mined, or are planned to be mined well below the local water table. This raises several issues that impact on mine safety, mining costs and regulatory approvals. Some pits will be æwetÆ, where they are mined through permeable horizons and where there will be measurable groundwater inflows. These will require some form of dewatering. There may also be some difficulties in the disposal of excess water. Other pits, may be ædryÆ, where they are mined through impermeable material and there are no measurable groundwater inflows but where there are stability issues related to hydrostatic pressures within the pit walls. These may require some form of depressurisation. Some pits are a combination of both. Effective management of groundwater inflows and groundwater related stability issues and the development of cost effective and environmentally acceptable dewatering and depressurisation systems requires an understanding of site specific hydrogeological conditions and practical experience in what works best for different conditions. The presentation will include an outline of the key hydrogeological factors that impact on large pits, practical methodologies for achieving dewatering/ depressurisation, and some case studies from the Goldfields, Pilbara and North Queensland.

Jan 1, 2003

By R deMoraes, A Bobet

The last decade has seen a resurgence of interest in lunar exploration and the emergence of countries like China and India as space fairing nations. In 2004, the US announced a new Vision for Space Exploration, whose objectives focused on human missions to the Moon and then Mars. The near future is likely to see the emergence of a worldwide drive to revisit the Moon as the first step in investigating the Solar System. To date, the Apollo missions provide our only experience of human operations on the Moon or anywhere else beyond Low Earth Orbit. Much was learned from these missions. However, their short duration means that many of the environmental effects that will be important for longer-duration missions could not be quantified. In addition, long-duration missions and infrastructure on the Moon require new technologies and capabilities, which must operate successfully and reliably in this lunar environment. Developing these technologies poses significant challenges for the exploration program. The paper discusses the risks associated with the construction of lunar surface and underground structures and the challenges to adopting the standards and rock mass classification systems developed on Earth and their applicability to the Moon. Moreover, an exchange of views to explore near-surface geologic and geotechnical profiles of the Moon is emphasized and implications of the lack of knowledge on rock mass characterisation of the Moonrock mass, the lack of theoretical/empirical experience on the use of rock mass systems outside Earth, and uncertainties.

Nov 29, 2022

Tumbling mills have been used in the minerals indusu) for occr WO years, with the design changing little, but the size of the individual pieces of equipment increasing significantly with the lowering of head grades, and the push for greater

Jan 1, 1997

By A Stradling

For a geometallurgical program to be successful, linkage must be made between the geologists and geostaticians who understand and model the orebody, the metallurgists who determine the value that can be extracted from the different geometallurgical units, and the mine planners who develop and optimise the plan to extract maximum economic value from the resource. One of the primary purposes of geometallurgical models is in the determination of the economic cut-off between ore and waste. Recognition of the level of confidence required in the estimation of grade, throughput and recovery is critical to the planning of a successful geometallurgical program. It also helps clarify the scope of work needed to mitigate risk at each stage in the development of a new mine projectThis presentation provides some of the author’s experience with development and application of geometallurgical models for existing base metal operations. It discusses how geological units defined by lithology, structure, alteration etc, can be translated into geometallurgical ore types defined by mineralogy, ore hardness, and flotation behaviour. Examples of how these characteristics have been used to estimate key economic parameters such as mill throughput and flotation recovery at two brown-field operations are provided. The first example relates to the modelling of metallurgical performance at Teck’s Red Dog zinc-lead mine in Alaska. Prior to 2000, zinc, lead and silver recoveries from a block of ore at Red Dog were either assumed constant, or were varied according to simplistic models. Throughput was not thought to vary substantially between blocks, so an average value was used for each blended stockpile. It is quite possible that some ore-value blocks were classified as waste, and some waste-value blocks treated as ore, as a result of poor understanding of the true economic cut off across the wide range of ore types observed at Red Dog. After an extensive flotation test program, the first assay-based zinc recovery model was developed for the Main pit reserve in 2003.**This is an abstract only. No paper was prepared for this abstract**

Sep 5, 2011

By C Tomlin, C Gimber

Historically, key closure risks have been studied during operations and then further assessed as cessation of mining approaches. Only in the past couple of decades or so has progressive rehabilitation and closure become an integral part of regulatory frameworks, sustainable mine planning and more recently, new project and development planning. It is now broadly accepted that the best closure outcomes occur when rehabilitation and closure are properly considered upfront, during the early stages of a mine development project and well before mining occurs. Increasingly, regulatory processes are requiring more diligence on early closure planning, often as part of the environmental impact assessment (EIA) and approvals process, rather than later in dedicated closure study phases. There is an opportunity to use the information generated during this phase to make better decisions on project selection, design, mining methodology and all other facets of the mining operation.

Aug 2, 2023

By N J. Grigg

Gekko Systems has developed an underground pre-concentration plant (Python) to reduce mine operating costs. Many ores liberate favourably using either high pressure grinding rolls (HPGR) or vertical shaft impactors (VSI). Using these comminution circuits for mineral liberation; rather than for the final recovery process and by utilising a high mass pull, high recovery process route (gravity/flotation), a narrow, low head, compact processing plant was developed that can sensibly be operated underground. The Python underground processing plant can provide a number of advantages for narrow vein mines including lower haulage costs, improved mine call factor and lower operating costs. The focus on fine crushing reduces the power requirement of the plant to approximately 8 kWh/tonne. The Python underground processing plant has been designed to be towed down the decline or lowered down a shaft, and is capable of being installed in sloping, non-linear drives for placement close to the working face. The overall benefit to mining companies of this concept has been estimated to be a saving in mining costs and a significantly smaller environmental footprint.

Jan 1, 2008

This paper discusses the implementation and potential limitations of the method for estimating sampling and analytical errors of multiple source mine output blended into a shipping product, described by Everett and Ziegelaar (2010). The practice of quality measurement varies between iron ore miners. The common objective is to monitor effective resource utilisation and control of product quality to customers. A flow diagram is given presenting the various options used by iron ore mine operators and the merits of the different options are discussed.

Mar 1, 2010