Search Documents

By Mathews K. E, Willstead T. V C

Initial glory holing was followed by sublevel stoping, with a small proportion of total production mined by shrink and cut-and-fill methods.The sublevel stoping method was successfully modified to cater for altering ground conditions encountered at increasing depths. At present, 94 per cent of production comes from sublevel stopes. The evolution of this mining method and current techniques and practices is outlined. A combined shrink and,sublevel benching method was also developed to increase the mining rate of narrow orebodies over the standard stoping lift of 380 ft. Pillar recovery and stope filling operations have been continuously modified to suit the relIuirements of a rapidly developing mine.INTRODUCTIONOre production commenced at Mount Isa Mines in June 1931. Since then production has increased from approximately 2,500 tons of lead ores per mine day to the current 11,000 tons of sulphide ores per mine day comprising 3,100 tons of lead ore and 7,900 tons of copper ore. The early planners selected sublevel stoping with ring drilling for ore breaking as the most efficient and economical for Mount Isa conditions: This method satisfied requirements for:1. a low cost mining method for the comparatively low grade ores,2. a stoping sequence allowing development, stope preparation, breaking and drawing of ore to proceed concurrently,3. a method of extraction in which broken ore in the stopes would be kept to a minimum because of adverse effects of oxidation on mill metallurgy and...

Jan 1, 1961

By D Van Doorselaere

The purpose of blasting during mining is to produce a muck pile that can be efficiently loaded and transported. There is an increasing awareness of the variation in muck pile characteristics and its economic implications. It is well known that good fragmentation by itself is not sufficient to optimise the muck loading efficiency. The swelling and configuration of the muck pile also significantly affect the productivity of the loading equipment. The characteristics of a muck pile depend upon the blast design parameters, explosive properties and rock mass geology. This study has focused on the dependence of muck pile configuration on blast design parameters, explosive properties and size distribution of the muck.The field work was done in two phases. In the first phase 12 blasts were monitored, while in the second, three blasts were monitored. The blast design parameters and explosive properties for each blast were documented and the following muck pile characteristics were measured:muck pile height and its distance from the facedistance of throwwidth of the power troughsize distribution by image analysis technique.The effects of burden, bench height, heave energy of explosive, row-to-row delay, powder factor and the mean particle size of the fragments on muck pile configuration were examined. It was observed that muck pile height and distance of throw are strongly influenced by the burden, bench height, heave energy of the explosive and the size distribution of the muck. The width of the power trough depends upon the row-to-row delay, powder factor and total burden. In addition, the effect of the fragment size distribution on the muck pile parameters has also been discussed.CITATION:Singh, S P and Van Doorselaere, D, 2015. The relationship between blasting parameters and muck pile configuration, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 369–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The Jurassic Walloon Coal Measures crop out over much of the Moreton Basin and contain numerous thin, banded coal seams which have been mined at various locations since the 1870s. Historically most mining has been by underground methods. Increased exploration during the 1970s and 1980s has led to the delineation of significant open cut coal resources and to the development of the Oakleigh, Jeebropillly and Ebenezer open cut coal mines in the Rosewood-Walloon area. Over 2 170 million tonnes in-situ of shallow, high volatile bituminous coal with a mean maximum vitrinite reflectance of between 0.5 and 0.6 have been proven in the Basin.

Jan 1, 1991

By N McIntyre, J Smart, J Ossa-Moreno, D Rivera

Hydro-economics is a field of research that analyses water resources from a multi-disciplinary approach (Harou et al., 2009). These models generally include one component that describes the water resources of the catchment being analysed (e.g. the physical behaviour of water), an economic component that describes users’ water demand function (changes of willingness to pay relative to availability) and a coupling methodology. These models go beyond calculating cash flows for water investments and analyse the economic behaviour of users when facing water shortages or surplus. In other words, water demand curves are defined for each water user (e.g. urban, agriculture, mining, environmental and hydropower), and they are used to retrofit the water resources component. As a result, the model approximates the catchment scale response to droughts and wet periods, including the effects of water markets, restrictions, recycling, water sharing and any cooperative efforts by users to adjust to changing climate conditions.These models are usually focused on agriculture and urban users, the main water consumers in most catchments, but they have sometimes included environmental, industrial and hydropower users (Bekchanov, Sood, & Jeuland, 2015). Nevertheless, although a relevant user of water in several catchments, the mining industry has been rarely included. This paper is part of an ongoing project that addresses this gap by developing a hydro-economic model in the upper section of the Aconcagua River in Chile. The aim of the paper is to analyse the sensitivity of the outputs of the model to changes in input data, both hydrological and economic, and to develop insight on usefulness of such models for reducing water conflicts in mining regions.CITATION:Ossa-Moreno, J, McIntyre, N, Smart, J and Rivera, D, 2018. Sensitivity of a hydro-economic model in a mining region to changes in hydrological and economic inputs, in Proceedings Life-of-Mine 2018, pp 52–55 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

While South Africa is well endowed with mineral resources, it is generally accepted that its future will be determined more by the development of its human resources than its mineral wealth. The country has throughout its modern history suffered from an over-supply of unskilled labour and a shortage of skilled and professional manpower. There has furthermore always been an over-reliance on Whites as an internal source of professional manpower, supplemented by immigration wherever possible. Better utilisation of other population groups in professional positions has been hampered by the general lack of education and training among such groups. Although many problems still remain, there are emerging trends which are likely to positively affect the training of professional manpower in the future. The direct and indirect influences that are likely to affect professional training at the macro level include 1. government policy and objectives in respect of manpower education and training, 2. the emergence of technikons as fully- fledged tertiary education institutions, 3. demographic trends in South Africa as they pertain to education, 4. political and statutory developments in the country, 5. industry involvement in tertiary education, and 6. professional registration.

Jan 1, 1986

By J Safarian, M K. Kar

Bauxite residue is one of the most important by-products from the alumina industry with no commercial use till now. The utilisation of bauxite residue through pelletising with different lime additions, hydrogen reduction, and smelting has been studied in this work. Three different types of green pellets were made with varying calcite-to-bauxite residue ratio and subsequently sintered at elevated temperatures. The sintered pellets were isothermally reduced at 1000°C under hydrogen gas followed by smelting of the reduced pellets in argon at 1500°C. Smelting of the reduced pellets leads to the recovery of metallic iron and the formation of a leachable calcium aluminate slag. X-ray diffraction (XRD) and scanning electron microscope (SEM) were used to characterise the phases and microstructural analysis. The iron produced in the smelting process has a high purity, above 99.5 wt per cent. While the iron content of the slags is quite low, and the slags shows variations of krotite (CaAl2O4), gehlenite (Ca2Al2SiO7), and perovskite (CaTiO3) phases based on the variation of calcite addition. It was found that the more calcite addition in pelletising yields higher percentage of krotite phase as compared to lower calcite-containing pellets. Employing quantitative XRD analysis, the krotite phase fraction was found approximately 85 wt per cent for higher calcite-added pellet, and around 74 wt per cent for lower calcite-added pellet. FactSage™, ver 8.1 (Thermfact and GGTTechnologies) thermodynamic software was used to evaluate the obtained experimental data, they both revealed that the

Jun 19, 2024

A non-contacting under-belt capacitance and gamma-ray backscatter technique has been developed for the on-line measurement of moisture in coal. In this technique, moisture was correlated with radio frequency susceptance and conductance determined using an under-belt capacitance sensor in which a fringing electric field Interrogates a layer of coal on the conveyor belt directly above the sensor. To compensate for variations in the density and thickness of the coal layer, an under-belt gamma-ray backscatter gauge was used to measure an equivalent volume of coal.A plant trial of the technique was conducted at Stockton Borehole Colliery, SW Australia, where the gauges were installed on the coking coal product conveyor. Product moistures, in the range 7 - 14%, were determined with r.m.s errors of 0.50 and 0.25 wt% using on-belt and static off-belt gauges, respectively. The difference in the on-belt and off-belt gauge measurement accuracy was attributed to sampling errors in the calibration of the onbelt gauge.

Jan 1, 1989

Soil improvement technologies have been widely employed over the recent decades to overcome tunnelling problems in difficult grounds, their range of application growing proportionally to the technological development. The constant advancement in the different mechanical (flexible and more powerful equipment) and electronic (enhanced reliability and direct quality control) aspects of these technologies, fostered the confidence of engineers and tunnellers and, ultimately, allowed the entire tunnel industry to approach difficult excavations in a safer and cost effective manner.This paper outlines the main features of commercially available soil improvement techniques, with particular emphasis on permeation grouting and jet grouting. These two technologies, developed concurrently in Europe and Japan, and there customarily adopted in the design of underground structures, have known extensive and extreme applications worldwide in recent years. Case histories and current practice of soil improvement techniques, as they apply to tunnelling, are also rendered.

Jan 1, 1999

By J N. Moncrieff

The resource estimation process for the underground Mount Isa Copper Mine has undergone significant change. Block models are now created using a commercial software package as opposed to the in-house software that was previously used. With mineralisation occurring over a strike length of more than 4 km, Mineral Resources for all categories totalled 190 Mt at 2.7 per cent Cu at 31 December 2002. Estimation is by ordinary kriging with two separate models generated to cover the X41 and Enterprise orebodies respectively. The underlying Upper Basement Contact and the silica-dolomite alteration envelope are both used as hard boundaries to constrain the modelling. From a validated block model, grade shells are generated at the appropriate cut-off grade for a given area. The grade shells are depleted for mined voids and subdivided into 30 metre strike length blocks. Application of a SMU criteria and crown and pillar constraints results in failed blocks being culled from the resource inventory. Mineral Resource blocks are further subdivided into resource categories (Measured, Indicated, Inferred) by the Competent Person on the basis of geological confidence, taking account of geological and grade continuity, drillhole spacing and structural complexity (JORC, 1999). A geostatistical æconfidenceÆ category is incorporated into the block model as an additional tool for the categorisation process. The shapes are assessed in concert with a mining engineer to determine whether a reasonable expectation of mining potential exists and if not they are removed from the resource. The final categorised blocks constitute the Mineral Resource inventory and form the basis for conversion to Ore Reserves. The resultant Mineral Resources and Ore Reserves are reported on an æinclusive ofÆ basis.

Jan 1, 2003

In Australia we usually define "resource" in purely material terms, and rarely relate it to intellect and human capacity. We look at the sheer abundance of our natural resources and are satisfied with the feeling that we don't really need-to rely on using our brains. Certainly our country is fortunate to have the mineral resources it does, but in many ways Australia's worst enemy is its "lucky country" syndrome because we tend to underutilise the great resource we have in the capacities of our people. Raw material exports will undoubtedly continue to contribute a major share of our export revenue, but to harness the riches our country has to offer most effectively we need the vision and planning necessary to bring together our material and human resources. There is a need not only to find, exploit and process our minerals economically, but to turn as much of our mineral wealth as possible into high value products before it leaves the country. In particular we must use our brainpower if we want to maximise economic benefit from and political influence over the strategic minerals which leave our shores. In the past we have been successful in finding and exploiting minerals because our mining industry has been in the forefront of private sector research and development. But if Australia is to have an advantage over other mineral rich countries in insulating itself from the effects of cyclical swings in commodity prices, then the future of the industry must lie even more in technological sophistication rather than depending. on such considerations as size and location of mineral deposits. To survive, our mineral industry must have the foresight and resourcefulness to make its own luck. There are two keys to increased efficiency in exploration and production and in further processing methods: enhancement of the skills of the workforce and continual improvement of R&D.

Jan 1, 1986

By A F. Cooper

The northeast-southwest trending ~25 km2 area incorporating Bald Hill is located 18 km northeast of Haast, and 5 - 7 km west of the Alpine Fault in South Westland, New Zealand. The geology consists of Greenland Group greywacke overlain by a Cretaceous-Tertiary sedimentary sequence and fluvio-glacial/marine terrace deposits of Quaternary age. Alluvial gold in Cole Creek, draining west from the summit of Bald Hill, may be derived either from vein mineralisation in basement rocks or from fluvial or marine terraces.   This paper focuses on the potential for in situ gold and base-metal mineralisation in sporadic, siderite-rich quartz veins that cut basement greenschist facies metasediments that have been overprinted by contact metamorphism.   Throughout the area, vein compositions are dominated by quartz and commonly feature zoned plagioclase. Alteration adjacent to veining within the contact aureole is dominated by 1 - 2 mm, coarse grained biotite, with small amounts of sulphide, and is pervaded by abundant siderite veinlets. Outside the aureole, wall rock alteration to veins consists of fine grained chlorite. Trace element XRF analysis has been used to ascertain base metal concentrations within samples of vein and alteration zones collected from throughout the area. Vein and alteration zone mineral assemblages containing <5 per cent sulphide, with low concentrations of As, Cu, Pb and Zn indicate low potential for gold and base-metal mineralisation in the Bald Hill region. Contact metamorphism of Greenland Group basement in the northeast of the region, is likely due to emplacement of a poorly exposed Cr- and Ni- enriched gabbro. The presence of biotite and andalusite in hornfelses indicate contact metamorphism occurred at temperatures >350¦C and at depths <10 km. Widespread vein distribution does not appear to be related to contact metamorphism or gabbro emplacement. Further research is required in order to establish the fluid source from which the veins were precipitated.

Jan 1, 2007

By P J. Bangerter, J Pan

Optimising for Net Present Value (NPV) with a strategic optimiser such as COMET, Prober-E, Blaser or Minemax has hitherto lacked a dynamic method for analysing the so-called third-order outcomes (such as Carbon emissions) of optimisation within life-of-mine planning. Optimisation, per se, has natural effects on carbon emissions in a life-of-mine plan. Contemporary strategic planning employs a mathematical optimiser to make sense of non-linear data (ie a block model) and produces a best-NPV optimised mining schedule, within a set of constraints. The very act of optimisation influences emissions, and in a dynamic way.

Aug 2, 2023

By Fisher AEJ

On Sunday morning 7th November, 1976, at approximately 2-25 a.m., smoke was discovered issuing from the 1912 m long belt drift at Appin Colliery. A Clouth steel cord rubber belt approximately 940 mm in width had been installed in the drift in 1963 on the basis that no fire resistant steel cord belt was then available to operate on a single lift at the load and on the 160 gradient of the drift. Investigation showed that the belt drift was on fire and the usually downcasting drift was upcasting. Immediate fire fighting and rescue operations were instituted and the drift was sealed off. High expansion foam was pushed into the drift from the surface and the fire was brought under control. Recovery work resulted in the fire being put out and the drift open for walking traffic by, S-P0 am., on Wednesday 10th November, 1976. lie experience gained during the fire fighting and recovery operations led to recommendations in regard to future use of high expansion foam.

Jan 1, 1981

By P Collins, C Sheriff

The Sand Queen gold mine is a typical Archaean narrow, high-grade gold quartz lode deposit within a shear hosted system. Initial mining during 1904 - 1948 produced 181 659 ounces of gold from 248 564 tonnes of ore milled at an average production grade of 22.7 g/t Au, which equates to a minimum of 750 ounces per vertical metre. The current mining operation is using the old Sand Queen main shaft to access the Sand George deposit, which is a narrow quartz lode system discovered in the same shear structure along strike to the south of the Sand Queen mine workings. Current underground resources contain 360 200 tonnes at a grade of 11.8 g/t Au for 136 500 ounces. Mining is scheduled to produce 20 000 ounces of gold annually. Re-opening of the Sand Queen mine and underground development of the Sand George lodes has revived several grade control issues relevant to a narrow, ænuggettyÆ gold lode mining environment. These include the dependence of assay grade of individual samples upon a number of factors, including how and where a sample is collected, how and where it is analysed, and how grade data is used to estimate an æaverageÆ grade. Ideally, the only way to achieve an acceptable estimate of ætrue gradeÆ is to mine and mill a large parcel of ore (eg >100 tonnes) from each lode or ore type. In a mining operation producing relatively small tonnages from a number of separate ænuggettyÆ gold lodes, availability of resources and operational constraints may preclude intensive sampling for predictive grade control. At the Sand Queen mine, one of the key issues has been to establish a reliable system for estimation of gold grade with which to reconcile milling data. Extensive use has been made of detailed geological data to understand the grade distribution within individual lodes and between lodes, so as not to rely solely on assay results.

Jan 1, 2008

By D Craw

The Hyde Macraes Shear Zone is a mineralised low-angle shear within the Otago Schist traceable for ~30 km with a NW strike. It is been actively mined along 12km of this strike, producing >6 Moz of gold. The shear zone consists of greenschist facies rocks with a mineralogy only subtly different from that of the host schist. Pervasive fluid flow has occurred along grain boundaries and within microshears which have been enhanced by the deposition of hydrothermal graphite. We model the development of these microshears using a threedimensional numerical code. For an inhomogeneous initial rock with lithostatic fluid pressures and a dynamic permeability deformed under dextral non-coaxial flow, deformation is distributed into weak shear bands. Graphite deposition and associated reaction-softening has a dramatic effect on the development of model shear zones. Graphite is deposited into a shear band, weakening it and further localising the deformation into that shear band, producing an anastomosing and interconnected shear zone structure such as observed in the HMSZ. The degree of graphite precipitation and graphitic-induced weakening are varied in the models. More graphite precipitation with a low degree of reaction-softening results in more diffuse shear bands. In contrast less graphite deposition but with a high degree of reaction-softening more leads to the development of more focused shear bands. Graphite deposition has clearly controlled the formation of the HMSZ structure, and is an important indicator of potentially mineralised structures elsewhere.

Jan 1, 2007

Mineral exploration conducted over a wide area of the State during the period 1960 to 1973 has resulted in the discovery of a number of significant deposits. Base metals, particularly copper, have been of prime interest while, more recently, the search for uranium and coal have assumed import- ance. Expenditure of $27.6 million by companies during the period under re- view has located 580,000 tonnes of cop- per, 370,000 tonnes of zinc, 350,000 tonnes of lead, 24 million Kg of uran- ium oxide and 2,500 million tonnes of coal. A variety of other metals and non metallic and industrial minerals have been investigated in a diversity of geological environments.

Jan 1, 1975

By G R. Hancock, D Verdon-Kidd, M J. Saynor, J B. C Lowry, T J. Coulthard

The ability to simulate the stability of post-mining landscapes over time scales ranging from decades to millennia is a critical element in the assessment of closure designs for uranium mines. Landscape Evolution Modelling (LEM) technologies provide a means to simulate and assess the long-term geomorphic stability of a conceptual rehabilitated landform for periods of thousands of years. However, a major issue with simulations derived from long-term modelling are the limitations associated with the data inputs. Specifically, simulations which utilise historic rainfall data only represent the variability of rainfall events that have occurred over a relatively short period. Consequently, these simulations run the risk of not accounting for the full range of rainfall variability that might be expected over an extended period of up to 10 000 years. Therefore, for this study a probabilistic approach was adopted to generate a stochastic synthetic rainfall data set to produce a series of unique rainfall scenarios, each representing a simulated period of 100 years. Importantly, utilising such an approach allows uncertainty in predictions to be better accounted for and provides a range or probability of likely outcomes.In this study, the effect of ten individual rainfall scenarios are assessed in terms of their impact on the predicted erosion and denudations rates produced by the CAESAR-Lisflood LEM for a conceptual rehabilitated landform of the Ranger Uranium Mine (RUM) in the Northern Territory of Australia, focusing on the Corridor Creek catchment (Figure 1). While legislation requires this site to be erosionally stable for at least 10 000 years (Commonwealth of Australia, 1987), here the focus is on the first one hundred years of landscape evolution, as this is the period in which erosion is expected to be higher, with limited vegetation cover or pedogenic development in the initial decades after rehabilitation. It is also the period where the drainage pattern is set.CITATION:Lowry, J B C, Verdon-Kidd, D, Hancock, G R, Saynor, M J and Coulthard, T J, 2016. Application of synthetic rainfall data to long-term modelling of a rehabilitated landform, in Proceedings Life-of-Mine 2016 Conference , pp 75–79 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Laing W. P, Neill D. M, O&apos

The Reward polymetallic massive sulphide deposit occurs 35 km south of Charters Towers, adjacent to the Highway gold deposit (Fig. 1). It is hosted within rhyolitic lavas and interlayered volcaniclastics of the Cambro-Ordovician Mt Windsor Volcanics. Reward is a "blind" deposit discovered in 1987 after a long history of exploration by various companies in the area. The main pyrite dominant massive sulphide body occurs under 100m combined thickness of Tertiary fluviatile sediments overlying deeply weathered gossanous volcanics. The exploration case-history provides a striking example of how geological and structural models can be built up almost exclusively from drill information. Four different styles and ages of mineralisation are present: 1) volcanogenic Cu+Pb+Zn+Ag+Au massive sulphides of probable syngenetic origin; 2) remobilised Cu+Au in massive pyrite of metamorphic/deformational origin; 3) supergene and 4) oxide Cu+Au mineralisation of weathering origin. The massive pyrite body, containing chalcopyrite lenses, transects the stratigraphy and is inferred to contain in excess of 5 million tonnes. Overlying the primary mineralisation a supergene chalcocite rich zone contains a measured/indicated resource of 634,231 tonnes of 6.77% Cu which includes 287,000 tonnes of 1.32 g/t Au and 18 g/t Ag. In addition a measured/inferred oxide resource of 309,000 tonnes of 5 g/t Au and 27 g/t Ag overlies the supergene zone.

Jan 1, 1989

By A Castillo, K Wiese, L Panduro Robles

For decades, organisations worldwide have been working to overcome challenges associated with new technology adoption while keeping up with rapid growth, development, and globalisation. In minerals processing, the challenges in developing and implementing solutions that contribute to the mining value chain are unique from other markets, as mining operations expect that world-class suppliers provide them solutions to gain a competitive advantage in their operation, production, performance as a financial asset, and as a long-term partner as we move into the future of mining. A simple shift in mindset is proven key to successful technology implementation. Change leaders must no longer think of their expertise in the area of application as their only responsibility; they must make a mental shift and see themselves in dual roles that strive to integrate the perspectives and needs of both developers and users. Successful change leaders must: (1) collaborate, seeking user involvement to ensure fit between product and operational needs, (2) demonstrate commitment to receive new technology, and (3) communicate to achieve an eventual shift of ownership from supplier to users that is seamless. Additionally, this strategy contributes to the mining value chain, as it allows developers and implementers to evaluate how change contributes to the asset’s position both within the company and in the commodities market. This paper will explain the shift in perspective for new technology implementation in detail and provide recommendations that operations can emulate, using examples of real challenges and lessons learned during a commissioning of the CYCLONEtrac™ Particle Size Tracking (PST) system at Cerro Verde’s C2 Concentrator. This concentrator has led technological change for plant optimisation, witnessed improved Net Metal Production (NMP), among other benefits with PST, the only technology in the market capable of providing real-time, online, and direct particle size measurement at the individual hydrocyclone level

Aug 24, 2022

By D Elmo, M Scoble, Y Liu, B Klein, J Scholar, S Nadolski

A cave-to-mill study being conducted at the New Afton block caving operation demonstrated the potential for sensor-based ore sorting equipment to reject waste and improve the grade of feed to the mill. The lack of selectivity and potential for dilution entry associated with the block cave mining method results in many caving operations having to mine and process material that is below cut-off grade at certain stages of production. Online monitoring and bulk sorting systems have the potential to alleviate this problem and improve the productivity of caving operations while reducing energy and water requirements for each tonne of concentrate produced.As part of the cave-to-mill study, the suitability of a range of sensors, such as X-ray fluorescence and induction-type sensors, to sort mine production at the New Afton mine was investigated. Results showed that the discrimination of ore and waste can potentially be carried out by implementing surficial sensors into the material handling system. The study also showed that a combination of sensor outputs could be used to identify a certain ore type so that pre-emptive changes can be made in the mill to improve beneficiation performance. Overall, the outcomes of the study on implementing sensor systems at block cave mines are considered to be of significant relevance to a number of existing and future caving operations.CITATION:Nadolski, S, Klein, B, Elmo, D, Scoble, M, Liu, Y and Scholar, J, 2016. Investigation into the implementation of sensor-based ore sorting systems at a block caving operation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 393–400 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016