Search Documents

By P C. Hagan, J Chen, S Saydam

Fully grouted cable bolts have been used in underground mining industry for more than 40 years and are becoming more and more popular especially when severe geological conditions are encountered, such as high stresses and large cross-section excavations. The axial performance of cable bolts are mainly relied on the load transfer process between the cables themselves and surrounding rock masses via grout annulus. Therefore, the selected grouts play a significant role in determining the reinforcement quality for underground openings. In order to better understand the mechanical properties of Stratabinder HP grout, which is one type of cementitious grouts commonly used in Australian underground coalmines, plenty of unconfined compressive tests are conducted on it. Following diverse standards, two different kinds of samples are prepared and tested with the w/c ratio ranging from 0.35 to 0.45. During the test important mechanical properties including uniaxial compressive strength (UCS) values, Young’s modulus, Poisson’s ratios and so forth are recorded. Based on experimental results, the effect of w/c ratio on the mechanical properties of Stratabinder HP grout is studied. Beyond that, influences of sample size on the failure mode, peak strength as well as residual strength of this kind of grout are summarised and analysed.CITATION:Chen, J, Hagan, P C and Saydam, S, 2014. Mechanical properties of cementitious grout serving in fully grouted cable bolting systems, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 269–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

The design and operating characteristics of the hydraulic cyclone elutriator were described in detail by Kelsall and McAdam (1963), and the method of operation of the commercially available version, the Cyclosizer, is described in the manufacturer's pamphlet (Anon). Complete details of the operating procedure are given in the relevant operating manual (Anon, 1964).The cyclones which form the basis of the Cyclosizer (Fig. 1) under normal operating conditions produce typical cut sizes of 44, 33, 23, 15, and 10 µm for cyclones one to five respectively for material with a specific gravity of 2·7. At the end of the selected elutriation period each sized fraction is discharged and collected for subsequent assay or analysis but all material rejected by the fifth cyclone (e.g. minus 10 \lm quartz) normally passes to waste. When this material is needed for separate study, although its amount and average analyses can be calculated by difference, it may be necessary to collect more than 250 I. of very dilute suspension, flocculate the solids, allow to settle, and decant off the supernatant liquid.This procedure is cumbersome and inconvenient and the simple technique to be described may offer some advantages. The temperature of the water fed to the Cyclosizer is maintained at a constant value for added reproducibility.PROCEDUREThe present overall treatment of the subsieve material (minus 37 \lm) fed to the Cyclosizer incorporated several refinements compared with normal operation and these may be best illustrated by anactual example. Material to be cyclosized (25 to 100 g depending on size distributIOn and specific gravity) is completely dispersed in water at 23 QC by vigorous stirrmg, using suitable dispersants if necessary, in a...

Jan 1, 1974

By J A. Meadows, M G. Annandale, G Castelain

Bauxite mining on Cape York Peninsula (CYP) commenced in the early 1960s in the region surrounding the town of Weipa. Rio Tinto Alcan (RTA) operates its bauxite mines on the homelands of 11 Indigenous Traditional Owner groups. The mining activity currently operates under three Aboriginal Agreements including an Indigenous Land Use Agreement – the Western Cape Communities Coexistence Agreement (WCCCA) – which provides RTA with access to the land in return for a range of benefits to the Traditional Owners, including employment, training, royalty payments and future relinquishment of the land (Klimenko and Evans, 2009). Despite reports of some ‘good progress’ in meeting the terms of the WCCCA (Klimenko and Evans, 2009, p 5), many of the region’s Traditional Owners remain dissatisfied. Two key areas of Indigenous community concern are the current premining management practices and the outcomes of post-mining landscape rehabilitation efforts.CITATION:Annandale, M G, Castelain, G and Meadows, J A, 2016. Sustainable mining – indigenous community benefit, in Proceedings Life-of-Mine 2016 Conference, pp 173–175 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By P Revell, G Wilkie, P Walters, L Keeney, F Faramarzi

Grade Engineering® is a value-driven strategy aiming to maximise benefits by exploiting intrinsic grade variability of ore deposits. It utilises a multitude of separation techniques to remove low grade material before being introduced to post-blast size reduction processes, i.e. crushing and grinding. At an operational scale, Grade Engineering® techniques can be implemented at the drill-and-blast stage, to control the degree of fragmentation in accordance with the spatial distribution of valuable minerals across an ore domain through differential blasting. It can also exploit intrinsic textural and breakage characteristics of a given ore type to reject uneconomical barren material at coarse sizes, which is known as Natural Deportment. Grade Engineering® can also be employed in the deliver stage of the mining value chain through sensor-based bulk and particle sorting. Each strategy is therefore highly dependent on the responsiveness of an orebody to available techniques. That is, the extent to which Grade Engineering® drivers would be capable of unlocking potential values of currently un-amenable orebodies depends on how detailed the heterogeneous nature of ore domains can be described. This paper considers exploring possible linkages between deportment characteristics of an ore and its competence when broken in a range of energy inputs at a particlebased level. Accordingly, potential opportunity may lie in exploring whether the intensity of input energy (or degree of fineness) can be used as a lever to improve or ‘unlock’ ore amenability to Grade Engineering® techniques. Implications from such a detailed approach offers new opportunities to enhance Grade Engineering® gains through engineering ore competence variability.

Nov 10, 2020

By B Poborowski, A Chen

"For some time, the Australian and Chinese underground coal mining industries have evolvedindependently with minimal infl uence on each other. Despite the fact that in recent years severaltechnologies and solutions have become common to both industries, this trend has seeminglycontinued to the point that there are still many important diff erences in legislation and hazardmanagement systems in both countries. Austar Coal Mine as an Australian based and Chineseowned enterprise has a unique opportunity to benefi t from the technology and knowledge ofboth nations. This paper compares the Australian and Chinese approach towards spontaneouscombustion hazard management in order to exchange experience, identify possible improvements and learn from each other."

Jun 1, 2012

By J J. Plumb, P D. Franzmann

A study was conducted to describe the microbiology of the MICCL Monywa chalcocite heap bioleaching operation. Microorganisms were detected in the heap using culture-based techniques and cultureindependent PCR-DGGE analysis of the 16S rRNA gene. The metabolic requirements, temperature and pH optima were determined for selected strains isolated from the heap material. Six strains (BH1-BH6) were enriched and isolated from heap solids and leachate samples. Phylogenetic analysis of the 16S rRNA genes showed that strains BH3 and BH4 were closely related to the acidophilic bacterium Acidithiobacillus caldus and strains BH5 and BH6 were closely related to Leptospirillum ferriphilum. The optimum growth temperature for L. ferriphilum was 41.3¦C and the optimum pH range was 1.1 to 1.5. A new species of Archaea was isolated from the heap samples. Cells of the proposed species, Ferroplasma cyprexacervatum (æcyprusÆ L.n. meaning copper; æexacervoÆ L.v. meaning æto heap upÆ), are non-motile pleomorphic cocci, capable of chemomixotrophic growth with ferrous sulfate and yeast extract. Cells grow anaerobically on ferric iron in the presence of potassium tetrathionate and yeast extract as electron donors. Growth occurs from 14¦C to 63¦C, with an optimum temperature of 55.2¦C. The optimal pH for growth was 1.0 - 1.2. The species was phylogenetically most closely related to Ferroplasma acidiphilum with a 16S rRNA gene sequence similarity of 95 per cent. Molecular analysis of mine samples (16S rRNA PCR-DGGE) detected the above-mentioned cultured strains of microorganisms as well as species of Sulfobacillus and other unknown Proteobacteria. The microbial community of the Myanmar bioleach heaps contained similar levels of diversity to a dump bioleach operation in Chile, but contained greater amounts of biomass than another heap bioleach operation in Australia. The operating parameters of the Myanmar heaps (low pH and moderate temperature) have selected for the growth of moderately thermophilic microorganisms that are more commonly found in extremely low pH acidic mine drainage sites than in heap systems. The novel species of Ferroplasma is thought to be involved in the aerobic and anaerobic cycling of iron within the heap bioleaching environment.

Jan 1, 2004

By Chappell B

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to he placed in a tailings darn. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electro- osmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

By R C. Cox

The Brukunga pyrite mine was operated from 1955 to 1972 to supply feedstock for sulfuric acid production in the South Australian fertilizer industry. Iron sulfide ore, mined by Nairne Pyrite Ltd, was finely crushed and concentrated onsite with the concentrates being sent by road and rail to Port Adelaide for roasting. Waste rock was dumped at two locations on the western side of Dawesley Creek and the tailings pumped to a valley-fill storage facility on the eastern side. Production of 1.5 Mt concentrate resulted in 3.5 Mt tailings and 8 Mt waste rock. The site has been administered by the South Australian Government since August 1977 and a lime treatment plant has been operated on the site since September 1980. Environmental issues arising from these operations included: diversion of Dawesley Creek to accommodate the waste rock dumps; dumping of low-grade sulfidic ore in waste rock dumps at the angle of repose immediately adjacent to Dawesley Creek; exposed fresh sulfide mineralisation in the quarry floor; tailings storage facility dam wall constructed by upstream up-lift using tailings and waste rock; an acid water pond sited on the tailings; and pollution of natural drainage. As a result, the minesite rapidly became a source of acid drainage and potential contaminants (sulfate, Al, Fe, Mn, Cd, Zn, and Ni). Various Government bodies have been responsible for considerable effort and expenditure in reducing the flow of acid seepage and contaminants into Dawesley Creek. Presently an estimated 60 per cent of seepage from the waste rock dumps, tailings storage facility and quarry is collected and neutralised prior to discharge into the creek. Tailings have been covered with waste rock, biosolids, neutralisation sludge and soil and planted with grasses, shrubs and trees to reduce rainfall infiltration. Monitoring of water flows, water quality and riparian ecosystems is on-going. Consultants have been engaged to develop cost-effective remediation techniques and a five-member Brukunga Mine Site Remediation Board was appointed to oversee remediation of the site and liaise with the community. Construction has commenced on the diversion of Dawesley Creek, and plans are being developed for the relocation of waste rock back to the quarry benches and upgrading of the neutralisation plant. The paper examines operations, environmental monitoring, remediation, research and community involvement with respect to current best practice.

Jan 1, 2003

By K Ehrig

Two irrefutable facts in geology and metallurgy are: ore deposits are comprised of variable mixtures of minerals which are systematically distributed throughout the deposit, and mineralogy exerts the primary control on metallurgical performance. If the distribution of process critical minerals can be quantified and mapped, then a logical assumption is that metallurgical performance can be predicted across the deposit.Olympic Dam is a +9 billion tonne Fe-oxide Cu-U-Au-Ag deposit which is hosted entirely within a magmatic-hydrothermal breccia complex consisting of over seventy ore and gangue minerals. Each has a unique set of metallurgical performance properties. Fortunately, 15 of the 70 minerals accounts for >98 per cent of the total rock mass.The mineral mapping journey commenced in the early drilling days shortly after the discovery of Olympic Dam in 1975. Geologists quickly recognised that the copper-iron sulphides had a predictable zoned distribution. However, geological models reflected the presence or relative abundances, not quantitative concentrations, of the minerals. This type of mineral mapping remained relatively unchanged for ~20 years and was of limited use outside of geology.Several things changed during the mid-1990s: assaying costs decreased significantly, instruments capable of automatically measuring mineralogy became readily available, the recognition of two quantifiable relationships at OD (ie mineralogy is a function of chemical composition (ie assays), and metallurgical performance is a function of assays, mineralogy, texture and process conditions. The linkage of metallurgical performance to mineralogy and mineralogy back to assays allows for every assayed sample in the resource model to be assigned mineral concentrations and metallurgical performance predictors. At Olympic Dam, block models (ie 3D maps) are routinely produced for 27 elements, density, 15 process critical minerals and greater than 50 metallurgical performance variables. These geometallurgy-enabled resource models are used for mine planning, process plant design and process optimisation studies. *This is an abstract only. No paper was prepared for this abstract.*

Sep 5, 2011

By R Dwyer

Iron ore currently mined in Australia generally requires very little beneficiation. However, depleting high-grade resources means that in the future low-grade iron ore deposits will need to be mined to meet the increasing demands of the global steel industry. Along with the increased demand, the industry faces additional pressure to reduce the environmental impact of mining and mineral processing. This has stimulated research beyond incremental improvements to conventional processing into alternative low-impact processes, including biotechnological approaches to mineral processing.Bioflotation and bioflocculation have emerged as relatively recent technologies, in which bacteria and/or their extracellular material may be used as flotation reagents (collectors or modifiers), enabling improved selective separation of minerals. The primary advantage is the production of a selective, environmentally-benign alternative to conventional flotation reagents. A biotechnological approach may also be taken in the beneficiation of high-phosphorous iron ores utilising bacteria capable of iron reduction and phosphorous solubilisation.Samples from three iron ore deposits in Western Australia were examined for bacteria suitable for iron ore benefi ciation. A number of common soil microorganisms including Pseudomonas spp, Limnobacter thiooxidans, Paenibacillus spp, and Ralstonia insidiosa were identified using culture-independent molecular techniques. A number of anaerobic species belonging to the genus Clostridium were also identified in the core samples. Selected aerobic species were enriched and isolated on high nutrient media in the presence of haematite. Several of the isolated strains showed an affinity for iron ore, attaching to haematite in enrichment cultures and further demonstrated through adhesion studies. Other isolated species such as Ralstonia isidiosa and Pseudomonas stutzeri are known to solubilise rock phosphates in soils and have potential for the removal of phosphorous from Australian iron ores.

Jul 11, 2011

By P Card

“Let’s get discipline and quality into easy to understand evaluations!” Project Managers and MetPlant Operators accept poor quality evaluations because they are generally unaware of what they should expect.The 2010 draft AusIMM ‘Guidelines for Techno-Economic Evaluations’ were collated by a subcommittee of practitioners and are regarded as best practice.They apply directly to projects and metallurgical plant evaluations, including those with a heavy technical basis. They can be applied to technical problem solving where there are no monetary computations. Project Managers and MetPlant Operators should demand that economic models and evaluations follow the six principles. They should become working tools which are easy to understand, fit for purpose, consistent, rigorous, record sources of input data, have key graphs and are rapid to audit.

Aug 8, 2011

By M Chen, W S. Ng, Y Liu

In the processing of refractory gold-bearing sulfides, pressure oxidation (POX) is commonly known for its role in liberating the gold in solid-solution via oxidation of the sulfide occlusions. For deposits that contain arsenic-bearing species including arsenian pyrite and arsenopyrite, POX serves an important secondary function in the fixation of arsenic, via the hydrothermal precipitation of stable arsenates such as scorodite and basic ferric arsenate sulfate (BFAS). There have been various investigations on the impact of different POX conditions on arsenic precipitation and the stability of the formed phases, but less is known about the changes to the arsenic carrier that occur in the curing stage, which follows directly from POX. The primary function of curing is to coax the dissolution of sulfates to reduce lime consumptions during cyanide leaching, and the slurry is kept at elevated temperatures near 100°C to achieve this. While the arsenic-bearing phases are expected to undergo transformation during this stage, there has thus far been limited experimental evidence. In this study, the effect of curing time and curing temperature on the arsenic-bearing species and arsenic deportment in the POX product has been investigated. Leaching of the curing products was also conducted to examine the stability of the arsenic species in the solid precipitates.

Aug 24, 2022

By I R. F MacCulloch

Bacterial oxidation of sulfide minerals is a familiar and commercially available process to enhance gold recovery with problem ores. Pintail Systems, a Colorado, USA based company had developed bio-processes for gold recovery based on natural mineral formation and transformation in a global mineral cycle. The biological recovery of precious metals from ore involves a number of mechanisms that are dependent on the metal-mineralogical association. These processes include: partial bio-oxidation of sulfide ores; oxidation of gangue minerals exposing gold to leaching; surfactant properties of bacteria/nutrient solutions that improve wettability of ores and solution contact with leachable gold and silver; and microbial production and excretion of trace amounts of gold lixiviants, and bio-fracturing or biological alteration of ore minerals. Pintail has demonstrated enhanced recovery of precious metals during cyanide detoxification of spent heaps at the end of mine life. Biological recovery processes also have the potential to be applied to in situ mining technologies. The in situ process application could recover gold from subgrade deposits, small deposits or those ore bodies with uneconomic stripping ratios for conventional mining. In situ biomining can be accomplished at a fraction of the cost of conventional mining and leaching and does not have the environmental liabilities associated with many conventional gold lixiviants.

Jan 1, 2004

Many block caving operations experience difficulties during undercutting, resulting in draw horizon damage, production loss and extensive drift repairs for the life of the block cave. This paper deals specifically with block cave undercut aims strategies, methodologies and management to avoid the problems indicated above.

Jan 1, 2000

By D Pepper

Despite the limited literature regarding the pressure filtration of mine tailings (compared to the large number of papers published each year on paste thickening of tailings) the number of mines dry stacking filtered tailings is approximately equal to the number of mines storing tailings in paste form. Main drivers for filtering tailings are: water recovery, future rehabilitation costs for tailings storage area and permitting requirements. In arid climates, the cost and scarcity of water justify the capital and operating costs associated with pressure filters. Further justification for filtered tailings is the potential for progressive reclamation of the dry stack, which can proceed earlier and faster than the reclamation of a tailings dam.Filtered tailings must be transported to the storage area by trucks or conveyors. For dry stacking, 70 - 80 per cent solids content (by mass) is typically acceptable, however the primary goal is to provide a filter cake that is consolidated and dry enough to prevent bridging and build-up on the materials handling equipment. It has been observed that high average solids contents (~70 per cent) can be achieved while the centre of the filter cakes is still wet and sticky, presenting challenges for the transportation of the solids. Appropriate controls must be in place to ensure consistently easy to handle solids are discharged from the filter.FLSmidth has installed two fine coal tailings dewatering systems in the United States. One of these systems incorporates a Deep Cone Thickener« upstream of the filter press to minimise the amount of water that must be filtered, while the other tailings filter press is fed by a high rate thickener. The operation and performance of these filters is discussed and compared to the lab testing used to size the full-scale equipment.CITATION:Pepper, D, 2012. Operation of filter presses for tailings dewatering, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 241-246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By L Clarkson, D Williams, P Redcliffe, F van der Wal

This research presents a snapshot and insight into the trends, patterns, and common considerations identified in the current standing of real-time tailings dam monitoring practice. Based primarily on information derived from concurrent research by the author (in form of a Catalogue of Real-time Instrumentation and Monitoring Techniques for Tailings Dams), challenges and opportunities when transitioning to a real-time monitoring system are discussed. Learnings and key considerations between different monitoring approaches are explored, including themes of limitations and advantages that were observed consistently through global supplier feedback.

Jul 1, 2021

The Porgera mine and treatment plant are located in the Enga Province of Papua New Guinea. Gold in the Porgera deposit is found free and in association with the primary sulphide mineral pyrite. The refractory nature of the gold in the pyrite r

Jan 1, 1997

By C MacRae, N Wilson

CSIRO Minerals has recently developed an electron microprobe (EMP) based imaging (or mapping) method for characterising ilmenite concentrates. The method requires an electron microprobe analyser to collect elemental X-ray maps which are then processed via an in-house developed software module (CHIMAGE). The type of information readily available from EMP mapping includes; primary phase identification, modal analysis of phases, chemical analysis of individual phases, textural information (eg the alteration stages in the formation of leucoxene or pseudorutile from primary ilmenite and the development of macro-porosity), and the identification of coatings or pore-fill material. All of these parameters will impact on the choice of future downstream processing options considered for any particular ilmenite concentrate. The method has been demonstrated to be a sensitive analytical tool for assessing the distribution of aluminosilicate minor impurities in ilmenite feedstocks from the West Coast of Australia and also for characterising the complex chrome-spinel gangue phases common in East Coast ilmenite concentrates from the Murray Basin.

Jan 1, 2001

By Inoue T, Takahashi N

To construct the accessing railroad line to the northern portal of Seikan Undersea Tunnel, nine tunnels amounting 7.4km in their total length were excavated through soft mudstones of young- er tertiary era with use of smaller-sized mechanic al excavators. Rocks were classified in four classes to which the tunnel support was designed respectively. Of several combinations of driving equipments stu- died comparatively, the method using the mechani- cal excavators was estimated to be the best choi- ce. The efficiency of the excavator was traced in every construction section and the data colle- cted was reviewed numerically. The result showed that the efficiency of the excavator dropped wh- ere the rocks were as hard as over 200kg/crif for compressive strength. And a few technigues in tunnelling i.e. contr- olling dusts in shotcreting, lattice arch, evaluati- ng measured deformations were tested and review- ed too.

Jan 1, 1987

Average annual growth in consumption of primary energy in Australia over the past 10 years has been 5·5 per cent compared to a world average of 4·1 per cent.Over the next 10 years growth rate is expected to increase to 6 per cent per annum due largely to the rapid development in the mineral processing industry.By the end of the 19705 natural gas is expected to supply more than 9 per cent of Australia's primary energy market. Coal will supply 40 per cent and petroleum products 47 per cent. Nuclear energy will make its appearance but will make only a small contribution in the period.Australia has adequate reserves of natural gas and coal to supply its needs in the 1970s and beyond. However the newly developed reserves of crude oil, while supplying 60-70 per cent of requirements in the initialyears, will need regular and sizable additions if they are to keep pace with the expanding consumption. For Australia to become self sufficient in the period 1970-1990 it is estimated that new discoveries will need to approximate ten times the volume of recoverable reserves found in Australia to date.

Jan 1, 1971