Search Documents

By A V. Ozsever

The selectivity in flotation columns involving the separation of particles of varying degrees of floatability is based on differential flotation rates in the collection zone, reflux action between the froth and collection zones, and differential detachment rates in the froth zone. Using well known theoretical models describing the separation process and experimental data, froth zone and overall flotation recovery values were quantified for particles in an anthracite coal that have a wide range of floatability potential. For highly floatable particles, froth recovery had a very minimal impact on overall recovery while the recovery of weakly floatable material was decreased substantially by reductions in froth recovery values. In addition, under carrying-capacity limiting conditions, selectivity was enhanced by the preferential detachment of the weakly floatable material. Based on this concept, highly floatable material was added directly into the froth zone when treating the anthracite coal. The enriched froth phase reduced the product ash content of the anthracite product by five absolute percentage points while maintaining a constant recovery value.

Jan 1, 2005

By Falbo A, Quarestima S, Cozza C, Barbaro M

A new synthetic reagent of the mercaptobenzoxazole class, 5- methyl-2-mercaptobenzoxazole, has been studied. This reagent exhibits powerful selective collecting action towards copper sulphides present in several complex ores, as demonstrated both by laboratory and pilot plant tests. Industrial production is expected to start in the near future. The way this reagent reacts with pure chalcocite has been studied utilising in situ FTIR techniques, adsorption tests, electrokinetic potential measurements and Hallimond cell flotation tests. The FTIR studies have indicated the nature of the surface phase. Adsorption isotherms obtained by the rest method have revealed the quantitative evolution of surface products, permitting the determination of surface coverage at various reagent concentrations. The electrokinetic potential has been utilised to verify the stability of individual species in diverse concentration ranges. Correlation of the results obtained has provided indications on the chemical interaction of this reagent with the surface and on the surface Arrangement.

Jan 1, 1993

By E S. B Santiago, C P. N Moreto, L V. S Monteiro, G H. C Melo, R P. Xavier

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Iron oxide-copper-gold (IOCG) systems of the Carajás mineral province (Amazon craton, Brazil) are structurally controlled by regional-scale shear zones and have formed by multiple episodes of fluid circulation and hydrothermal alteration in the Neoarchean (2.71–2.68 Ga and 2.56 Ga) and Palaeoproterozoic (1.90–1.87 Ga).Collectively, fluid inclusion, boron, oxygen and hydrogen isotope data and Cl/Br–Na/Cl ratios in fluid inclusions reveal that regional circulation of non-magmatic brines (eg evaporative fluids/evolved sea water) and mixing with other fluid sources (eg meteoric or magmatic) is an important attribute in the genesis of the Carajás IOCG systems. The ?33S and d34S compositions of sulfides from the Neoarchean and Palaeoproterozoic IOCG systems suggest that the ore-bearing fluids have assimilated sulfur from crustal reservoirs. Nevertheless, most ?33S measurements have indicated mass independent fractionation (MIF) effect for both systems which points to the possible involvement of surface sulfur sources.CITATION:Xavier, R P, Monteiro, L V S, Moreto, C P N, Melo, G H C and Santiago, E S B, 2015. Non-magmatic versus magmatic fluids in the genesis of Archean and Palaeoproterozoic iron oxide-copper-gold systems of the Carajás Mineral Province (Brazil), in Proceedings PACRIM 2015 Congress, pp 281–288 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M Zoorabadi

Overcoring is a common technique to measure in situ rock stress using the concept of stress relief. The strains measured during overcoring are used to calculate the stress tensor assuming continuous, homogeneous, isotropic and linear elastic behaviour. This approach does not recognise any effect of the thickness of the rock annulus produced during overcoring instead assuming that the stresses are entirely a function of the difference in strain between the start of the overcoring and the end with no regard to the transient strains produced. Three-dimensional numerical modelling was used to simulate the overcoring process and investigate the impact of core diameter on the transient stresses and strains during overcoring. This study showed that in thicker core, maximum transient axial stresses and strains occur when the drill bit approaches the measuring point and greater tensile axial stresses were produced when the annulus was thinner. CITATION:Zoorabadi, M, 2018. Numerical study of annulus thickness on overcoring stress measurements, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 274–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By F T. Suorineni

Empirical methods are deeply rooted in geomechanics. This is a consequence of the recognised complexity of the nature of the rock mass. The usual assumptions of material continuity, homogeneity, isotropicity and linear elasticity often assumed for soil, concrete and steel are difficult to justify in a rock mass except for mathematical convenience. These assumptions form the bases for most mechanistic, analytical and numerical methods in geomechanics. Believers in empirical methods argue that the complexity of the rock mass and its interaction with structures developed in it is adequately accounted for in empirical methods, which compensate for our ignorance.Franklin (1993) defines empirical design as quantified judgement based on experience. He further states that empirical methods often prove ‘closer’ to the ‘truth’ than the apparently more precise predictions of theoretical analysis, adding that based on real data empirical methods provide a standard against which theoretical predictions are measured and can be judged. This paper takes a critical look at the common empirical methods in geomechanics – rock mass classification systems (Bieniawski, 1973; Barton, Lien and Lunde, 1974; Hoek, 1994a), Laubscher block caving design rules (Laubscher, 1994), the stability graph (Mathews et al, 1981), pillar design equations (Salamon and Munro, 1967; Hedley and Grant, 1972; and their derivatives), pillar design chart (Lunder and Pakalnis, 1997) and failure criteria (Hoek and Brown, 1980; and its derivatives). The common thread in the application of these methods is that in most cases they are often applied blindly without an understanding of the underlying assumptions and database limits. This paper emphasises that users of these methods need to know the underlying assumptions, database limits and inherent hidden risks that are often unmentionable for their satisfactory use. Finally, suggestions are provided for the efficient use of empirical methods and how they can be improved.CITATION:Suorineni, F T, 2014. Reflections on empirical methods in geomechanics – the unmentionables and hidden risks, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 143–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

The general types of industrial behaviour of liberated valuable sulfide minerals in the 0 - 10 ¦m size fraction are described and tests to explore on site at a concentrator the general nature of any deficient behaviour are discussed. In addition, the general types of behaviour of the gangue minerals in this size fraction are also described in terms of their mechanisms for recovery. These behaviours are also discussed in terms of the type of grinding device and grinding environment in which they were produced and the target grinding product size. Major recent improvements in the industrial capabilities of grinding devices are discussed.Present difficulties in characterisation of particles in the 0 - 10 ¦m range are described and desirable improvements for the future are outlined. Further, desirable improvements for industrial processing of valuable minerals in this size range are discussed along with some remedial actions.

Jan 1, 2005

By van der Walt TJ, van Deventer JSJ, Reuter MA

Owing to their complexity, many metallurgical processes are difficult to model fundamentally, and as a result more attention has been focused on the use of artificial intelligence techniques to simulate these processes. In this paper recent advances in the use of neural nets to model processes not amenable to conventional methods are discussed. These include the application of a new modelling methodology based on the use of neural nets for the dynamic simulation of metallurgical processes, the use of conventional techniques in conjunction with neural nets to simulate gravity separation circuits, as well as the detection of gross errors in variable measurements by means of a neural net representation of the relation between measurement and constraint residuals.

Jan 1, 1993

By M I. Pownceby, N A. S Webster, J R. Manuel, J M. F Clout, E Donskoi, N A. Ware

The relative influences of sinter mineralogy, sintering temperature, solid and pore macro- and microstructure on iron ore sinter physical strength are not yet fully understood. Whilst a range of analysis techniques have been used by researchers to evaluate sinter physical properties and sinter mineralogy, none have been able to directly link sinter mineralogy and physical strength under controlled conditions. CSIRO has developed a unique laboratory method to study the fundamental melting properties of fine iron ores in a laboratory furnace under a controlled temperature and gas atmosphere environment designed to simulate the industrial sintering process. Compacted tablet samples for a 0.41 per cent and a 2.5 per cent Al2O3 series were fired in a tube furnace at various temperatures, cooled, then tumbled using a modified Bond abrasion test apparatus to determine a relative tumble index (TI) at each temperature. Quantitative XRD (QXRD) analysis was then carried out on the tumbled samples and optical image analysis (OIA) was conducted on polished sections of a separately fired compact in each case. The amount of total SFCA was found to decrease with increasing firing temperature for both alumina series with the total amount of SFCA higher in the 2.5 per cent Al2O3 series compared to 0.41 per cent Al2O3 series samples. The increase in the amount of magnetite and hematite with increasing firing temperature was largely at the expense of a decrease in total SFCA. Overall, there was good agreement between the quantitative mineralogy determined from QXRD versus OIA for SFCA, hematite and magnetite. Qualitative analysis of high magnification images of the sinter correlated with both the OIA and QXRD results.

Sep 18, 2023

By R A. Anand, N N. Viswanathan, M M. Pande

Slags are the most voluminous solid by-products generated in pyrometallurgical operations, and, as such, finding an application for these oxidic materials is pertinent to maintaining resource efficiency. In particular, pyrometallurgical copper production is associated with high slag rates, typically ranging from 2.2 to 3.0 tons of slag per ton produced copper, which necessitates slag valourisation. A possible application for these iron silicate slags is as supplementary cementitious materials (SCMs), which effectively lowers the CO2 emissions per ton of cementitious material. Although utilising iron silicate slags as SCMs has been studied in previous work, the scientific literature has limited data on the effect of composition on the inherent reactivity in cementitious systems. More specifically, no reports on the impact of FeO/SiO2 ratio have been presented in previous publications. Therefore, the present study aimed to isolate this parameter in a synthetic FeO-SiO2-Al2O3-CaO-MgO-Cr2O3 system. Since the amorphous content is a pertinent parameter for SCMs, a high-temperature confocal laser scanning microscope (HT-CLSM) was utilised to assess the crystallisation behaviour at continuous cooling conditions. Furthermore, high-temperature rheological experiments were conducted to measure the viscosities of the slags in relation to the crystallisation behaviour. The experiments showed that depolymerising the slag by increasing the FeO/SiO2 ratio generated a less viscous slag, which showed higher tendencies for crystallisation. Furthermore, experiments assessing the inherent reactivity as an SCM showed that depolymerising the slag by increasing the FeO/SiO2 ratio as the sole independent parameter generated an initially more reactive slag. However, replacing SiO2 with FeO was found to negatively affect the reactivity as measured over seven days within the tested compositional range.

Jun 19, 2024

Lateritic nickel ore occurs as a supergene or residual deposit as a result of the tropical weathering of underlying ultramafic rocks. The mineralisation may be as hydrated Ni-Mg silicates, like garnierite (silicate ore); or as hydrated Ni-Fe oxide (oxide) ore. Non-sulphide ore represents only 30% of the tonnage mined, but represents 85% of the total world's nickel reserves. A typical lateritic profile consists of 4 zones above the unweathered ultramafic parent rock: Zone 1: the "upper laterite" which is dark red-brown, porous and concentrically structured. It contains 0.2 to 0.8% Ni, 48.0 to 72.0% Fe, and 0 to 9.5% MgO. It is often capped by a ferricrete crust. Zone 2: the "middle laterite", which is red-brown to light brown and more porous than the above zone. It contains 0.8 to 1.5% Ni, 42.0 to 48.0% Fe and 0.5 to 6.0% MgO. Zone 3: the "basal laterite" which is yellow-brown to yellow-orange,

Jan 1, 1974

By Sivell W

We discuss the origin of the Patuki ophiolite complex and the Dun Mountain ultramafics of Middle Permian age in Nelson, New Zealand. It is shown that the Patuki volcanics have strong affinities with tholeiites of mid ocean spreading ridges transitional to alkaline basalts similar to those from fracture zones and ocean islands. At D'Urville Island, typically pillowed alkaline basalts enriched in rare light rare earth elements (LREE) - ophitic spilites - are associated with LREE-depleted (N-MORB-like) tholeiitic spilites with intergranular textures. The metabasalts are associated with a wide variety of sediments, and with sediments are intruded by conformable sheets of serpentinite. Coarsely crystalline mafic and plagiogranitic rocks signify vents and magma chambers, and we propose that the group developed as ocean crust from a slowly spreading mid-ocean ridge, transform association, overwhelmed at intervals by volcaniclastic sediment. Detailed mapping at a scale of 1:5000, and stratigraphic and geochemical development and structural coherence, show that the group is not melange in the Franciscan sense. The Dun Mountain Group, of serpentinites, peridotites, dunites, gabbros and other rocks, intruded the upper Patuki Group as a linear series of aligned pods and sheets. They carried up with them tectonic inclusions of older rock, which were metasomatised, and altered wall-rock, and one low angle dike passed several hundred metres into overl~ing sediment, at moderate temperatures (500 C). The rocks did not act as a floor (and alleged source) for the Patuki, but partly post-dated and were emplaced into Patuki.

Jan 1, 1987

By T A. Short, P L. Brown

Kestrel Mine co-disposes around 1.5 Mt of fine (2SO4/t and to date around 9 Mt has been deposited. The mine plans to co-dispose of approximately 39 Mt of material, creating a dump with a maximum height of 35 m and a disturbance footprint of 260 ha. Benign materials suitable for rehabilitation are severely limited and no successful rehabilitation strategy has yet been demonstrated. A rigorous measurement and modelling program is resolving outstanding issues associated with acid rock drainage (ARD). The objective of the program is to develop and validate a strategy for dump rehabilitation that will control ARD and allow for mine closure. The strategy includes using a soil cover to reduce water flux into the dump to control the overall oxidation rate and to control effluent release. Monitoring of the oxygen distribution and water flux in the uncovered material commenced in February 2001 and monitoring in waste under a trial cover commenced in February 2002. Carbonaceous and sulfidic oxidation rates have been measured. Initial modelling indicates that the carbonaceous material has the general effect of slowing the rate of pyrite oxidation, lowering the maximum sulfate production rate and extending the time to oxidise all the sulfides. The combined approach of measurement and modelling provides a sound basis for assessing the performance of the trial cover and predicting the long-term quality and quantity of effluent at the base of the rehabilitated waste dump.

Jan 1, 2003

By R Dimitrakopoulos, R Senécal

This paper presents a metaheuristic solution to the optimisation of open pit long-term production scheduling with a stockpile and geological uncertainty. The optimisation formulation is a two-stage stochastic integer programming (SIP) model that determines the optimal mining sequence that maximises the total discounted cash flow, while penalising for high deviations from production targets. A parallel implementation of Tabu Search is proposed to accelerate the solution of the SIP formulation and take full advantage of multicore computer processing. Different variants of the proposed algorithm are applied to a case study to assess the performance of the parallel approach. The proposed algorithm and variants are benchmarked using linear relaxation of the complete problem to determine robustness and provide a better overview of the related performance. The results show a net improvement over the sequential solution, and the new proposal seems to be promising when working with a large-scale data set.CITATION:Senécal, R and Dimitrakopoulos, R, 2014. Parallel implementation of a Tabu search procedure for stochastic mine scheduling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 405–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Z Chang, S A. Mrozek, S Windle

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. It is important to understand skarn-porphyry transitions in order to use exposed skarns to look for associated and potentially larger porphyries. For such purposes, a good start is to understand the transition between porphyry and skarn in known deposits. In this contribution, we report the transition at Antamina, Peru, where skarns occur in and around a Miocene complex comprised of more than seven porphyritic intrusions. There are three types of skarn-porphyry relationships. The earliest intrusive phase, P1A, contains both endoskarn and porphyry-style quartz veins with secondary biotite halos. The porphyry quartz veins and endoskarns formed at the same time. Locally, the intrusion contains only endoskarn without porphyry quartz veins and is surrounded by exoskarns in carbonate wall rocks. In the third scenario, later porphyry (P2) intruding into P1A porphyry and skarns related to P1A contains abundant granular quartz veins and secondary biotite alteration but does not have significant endoskarn. The granular quartz veins also extend into earlier P1A skarns. The scarcity of endoskarn associated with P2 is related to the supply of Ca. The earliest P1A intrusion intruded into carbonates that supplied abundant Ca, therefore both endoskarns and exoskarns formed. In contrast, where the wall rocks of the later P2 intrusion are P1A or skarn related to P1A, there was little free Ca, therefore only porphyry-style quartz veins formed.CITATION:Chang, Z, Mrozek, S A, Meinert, L D and Windle, S, 2015. Skarn-porphyry transition – an example from the Antamina skarn, Peru, in Proceedings PACRIM 2015 Congress, pp 409–414 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Warrego copper ore characteristically contains 0.05-0.2% bismuth, which on upgrading produces a concentrate of approximately 1.3% bismuth. Early smelting of this concentrate (1973) was accomplished in a flash furnace (eliminating 92% of the bismuth in the con- centrate) and Top Blown Rotary Convertors (eliminating 85% of the bismuth in the matte). However 1.3% bismuth was considered the max- imLun bismuth level that could be treated. Geological evidence indicated that the bismuth level in~the copper ore would increase and that the bismuth level in the Warrego ore would be 0.3-0.7% bismuth. Treating these ores would produce a copper concentrate with bismuth levels far in excess of those accept- able to the smelter and still produce low bismuth content blister (limit 0.03% bismuth).

Jan 1, 1984

By M Goers, M Almond

"The use of reverse circulation (RC) drilling for grade control sample collection was selected by the Pueblo Viejo Mine Geology department at the recommencement of the operation in 2010. This method was selected because it allows: for multi-bench drilling (60 m hole depth, four benches of mining) to aid mine planning and provide a detailed close spaced drill data comparison with the reserve model angled drill holes to optimise the drill hole interception of the vertically controlled mineralisation dry sample collection in areas of excessive surface and groundwater mining operations to commence with the long assay return period (due to the need for the samples to be shipped overseas for analysis) until the on-site laboratory is operational.To date, 118 302 m of drilling has been completed throughout the operations of two open pits: Monte Negro and Moore. Two drill rigs (contractor and site-owned and operated) with three generations of sampling systems have been used to date. Throughout the drilling a 20 per cent quality assurance, quality control (QAQC) sample check (blanks, field duplicates and standards) have been used to check the drilling and laboratories performance. In addition, a total of 1104 fines samples were collected to compare the drill chip samples collected and the fines lost with two of the sample systems used.The drilling to date has highlighted the need for a complete and coordinated system to be used before sufficient confidence in the quality of the samples collected is achieved.The complete system must be set-up and coordinated to obtain the best quality sample possible. This complete package includes: drill bit size and shape for the rock being drilled and mineralisation targeted face sampling hammers with the correctly sized hammer shrouds sample hose routing to reduce sample flow turbulence and choking blow-down valves to eliminate drill hole water that has entered the drill string during rod changes correct drilling techniques targeting sample quality a sample system that captures the fines for inclusion into the sample.These improvements can be obtained without reducing the drilling rates.The measurements required to demonstrate the improvement in the sample quality will be the focus of future work within the department.CITATION:Goers, M and Almond, M, 2012. Bit to bag - The importance of a total coordinated system in reverse circulation drilling, in Proceedings Sampling 2012, pp 65-72 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By J C. Koppe, L Vieira

One common problem for blasting in iron ore mines with significant weathering is the occurrence of large blocks of hard rock mixed with softer material. This situation causes a problem for blasting design and sometimes produces large boulders of rock that require a secondary blasting, as well as excavation difficulties. To minimise this situation, geophysical techniques were used to identify the hardest material amid the weathered material. To study the problem, seismic, ground penetrating radar (GPR), electrical resistivity and induced polarisation (IP) methods were used in an intensely weathered Brazilian iron ore deposit. The methods of GPR combined with IP, resistivity and seismic showed to be effective in modelling the contrast among hard, friable materials and soil. The results were used to improve the geological model and create more favourable conditions for the subsequent blast design. The blast design based on geophysical/geological models resulted in significant improvement in the fragmentation of the iron ore. This was achieved by the adoption of a specific drilling pattern for a given geological situation. With the new specialised blasting design the formation of boulders was eliminated.CITATION:Vieira, L and Koppe, J C, 2015. Geophysical techniques applied to blasting design, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 289–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J F. Costa, A Grigorieff

Coal mining reclamation is a worldwide concern. This paper presents a Brazilian example where the economic aspects of reclamation are considered. The basic goal of the study is to transform the reclamation procedures into an economic process by integrating the use of land after reclamation and developing profitable post operations. Some of the activities considered in this case study include: using of the coal pit as a landfill, considering appropriate landfill design and construction; using the area for forest development; and developing grassland, forests of native species and the construction of ponds for fishery. This study will conclude that the mined area is: capable of storing large quantities of waste at a competitive cost and at a low environmental risk; commercial forest development is economically feasible; and the lakes and other reclaimed areas can be integrated into the landscape creating a fresh water supply and an area to raise cattle.

Jan 1, 2005

By L Dubron

This study details a mineralogical and textural characterisation of West African iron ores with an emphasis on their behaviour during mineral processing. By means of both qualitative and quantitative characterisation, a simulation of the beneficiation process applied to these iron ores is performed. A series of different analytical tools are used, including:X-Ray Diffraction (XRD) for qualitative mineralogical analysis;• qualitative optical microscopy (phase identifi cation, description of micro-textures) and (semi)• quantitative optical microscopy (counting of particles, phases and textural types); and• chemical analysis.All the information provided by these analytical methods are combined into a quantitative mineralogical and textural analysis, here called ‘modal analysis’, which enables us to simulate the capability of West African iron ores to be benefi ciated by magnetic and gravimetric separation techniques.On one hand, both qualitative XRD and optical microscopy have revealed the presence of the following mineralogical phases: magnetite, haematite, goethite and quartz. On the other hand, the chemical analyses provide us with quantitative inputs expressed as oxides. We have converted the oxides into mineralogical contents expressed as magnetite, haematite, goethite and quartz. In this way, we build a simple quantitative mineralogical analysis.Beside this, the semi-quantitative approach of the characterisation by optical microscopy also provides us with a liberation study, enabling us to split the gangue-bearing content between two types of particles:1. liberated gangue-bearing particles, and2. composite particles composed by both iron (oxhydr) oxides and gangue-bearing minerals.We have assumed that we could anticipate the behaviour of these two kinds of particles through a mineral process, by simulating the removal of at least the liberated particles of gangue. Optical microscopy also revealed a trend in the weathering profi le of the Tokadeh ore horizon with a decrease from bottom to top of magnetite and an increase of both goethite and martite showing a higher level of oxidation and hydration in the upper ore horizon.We have applied this removal extent upon the quartz content of the mineralogical quantitative analysis and we have re-calculated the quantitative mineralogical analysis considering the expected decrease in the quartz content. Finally, by converting the re-calculated (oxhydr) oxides contents into iron grades and summing them, we do obtain a fi nal simulated iron grade for the upgraded products.

Jul 11, 2011

Longhole open stoping was introduced in the zinc-rich 'B' lode at New Broken Hill Consolidated Limited (NBHC) during 1968. Since then one longitud- inal and a series of transverse longhole open stopes have been developed. The longholes are drilled using Gardner Denver airtrac drilling jumbos and the broken ore is loaded from drawpoints and transported to chutes using Wagner ST5 scoop- trams. The holes were drilled from sill stopes 160 ft apart. The width of an emptied transverse longhole stope was successfully widened by blasting rings of blastholes drilled parallel to the stope wall. Proposed stope and pillar designs for a series of transverse longhole open stopes were assessed using a method of finite element analysis, applied to a longitudinal section through the area. Blastholes have been surveyed for dip and bearing using an Eastman borehole survey camera. The data produced has provided the basis of a study of blast- hole deviation. Deviation of boreholes is considered to be the major cause of the formation of benches in longhole stopes.

Jan 1, 1971