Search Documents

By D R. Seaman, B Adamson, P Sharman, M McMahon

"The Telfer processing plant commissioned its pyrite regrind and flotation circuit in August 2012. The circuit was designed to regrind pyrite concentrate to a p80 of <30µm then float a gold and copper rich concentrate before tails from the flotation circuit fed the carbon-in-leach (CIL) circuit downstream. Expected benefits were: improved CIL performance that would result from the finer grind and a reduction in cyanide soluble copper to the CIL circuit, as well as a small increase in overall flotation circuit recovery. While the benefits of a finer grind were soon realised, recovery in the post-regrind flotation circuit (named the ‘pyrite recleaner circuit’) was consistently and significantly lower than that expected based on laboratory test work. Selectivity in the pyrite recleaner circuit was virtually nil and copper reporting to the CIL circuit did not change as a result of the pyrite recleaner circuit operation.A pulp chemistry survey of the plant and comparison with the lab showed that the dissolved oxygen (DO) demand in the plant was much higher than that in the lab. Lab flotation tests conducted using nitrogen gas instead of air resulted in recoveries similar to those from the plant. It was identified that the freshly ground pyrite surfaces exiting the regrind mill were consuming oxygen in the slurry and there was insufficient oxygen available for collector adsorption and pyrite depression to occur. Test work, using a pilot regrind mill, showed that a reduction in grind size resulted in an increase in DO demand.A range of oxidising agents were tested in the laboratory and using a pilot flotation rig set-up in the plant. Oxygen was found to be the most reliable and effective agent and options for increasing oxygen delivery to the plant were explored. Scale-up from the lab oxygen requirement to the plant is difficult and efforts to implement a permanent solution for meeting the DO demand in the plant are ongoing.Citation:McMahon, M, Seaman, D R, Sharman, P, Adamson, B and Seaman, B A, 2016. Optimising the Telfer Pyrite Regrind Circuit - Effect of Dissolved Oxygen Demand, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 51–58 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By R Saha, D Barry, C Mawdesley, O Bertoli

Kriged estimates are not typically calculated on blocks substantially smaller than the sample spacing (eg the Standard Mining Unit or SMU). Moreover, the sample spacing for quality variables is often much greater than the SMU size. For short to medium term planning decisions, the shorter term variability in the quality variables is a key economic consideration in defining, setting and meeting coal product specifications.Global uncertainties can be calculated using Drill Hole Spacing Analyses (DHSA). However, knowing the precision of a variable for a one or two year production volume is usually not adequate for variables with low spatial continuity that may fluctuate significantly over daily, weekly, SMU, or shipment volumes.Is there a feasible, reasonable and valid geostatistical method to model the uncertainty of coal quality variables on blocks substantially smaller than the drill spacing (say on the SMU)?The validity of using co-kriging variances, calculated on SMUs to characterise local uncertainty, was tested using a suite of conditional simulations generated for several quality variables for BHP’s Blackwater operation. The conditional simulation results were used as a benchmark against which the results derived from the kriging variances could be compared.The agreement between the kriging and simulation methods for thickness is excellent, with much closer correlations than for the quality variables. Typically, the kriging variances give very reasonable approximations to the simulation-based uncertainties, although there could be some systematic discrepancies which may become much more critical if a classification is to be based on a thresholding of the SMUs relative uncertainties.CITATION:Mawdesley, C, Barry, D, Bertoli, O and Saha, R, 2017. Local uncertainty benchmarking – a coal case study, in Proceedings Tenth International Mining Geology Conference 2017, pp 43–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By D Connelly

Quartz deposits are common in nature but the presence of quartz suitable for yielding high purity quartz is exceedingly rare. This paper describes a test work study on producing high purity quartz (HPQ) product to meet the tight product specifications of greater than 99.97per cent, including four and even five nines, for uses including, lighting and fibre optics and modern-day high efficiency solar panels. Due to demand in renewable energy applications the market for high purity silica solar panels known for their increasing efficiency and durability is rapidly growing. Demand continues to rise for the use of high purity quartz in semiconductors, electronics, imaging and sensor markets. Microelectronic components are created by chemically fabricating wafers of semiconductors such as silicon to obtain the desired transport of electrical charge and control of the current. The production of silicon metal from high purity quartz has been designated a Strategic Mineral by the European Commission and by the US Department of Justice due to the growing significance of this metal in various industries. The subsequent processing of quartz is the key step to adding value and aiding technological advances. Overall, the high purity quartz market is a highly secretive, specialised market with increasing opportunities for stakeholders. The attempt to produce HPQ in this work was carried out using an Australian quartz ore following a typical HPQ process flow sheet. The unit processes included primary crushing, scrubbing, magnetic separation, flotation, acid leaching followed by hot chlorination. The results indicate that grinding of quartz requires specialist equipment due to the hardness and extreme abrasiveness of the ore leading to additional iron contamination in the ground ore. The critical impurities were aluminium, iron, sodium, potassium, lithium, titanium, zircon, calcium and magnesium. The chemical refining was found effective. The hot chlorination process needed to be done at 1200°C in a chlorine – hydrogen chloride gas atmosphere. The risk of any gas being released during this stage is very serious and only specialist companies should and can carry out this step. More recent studies reported many new options that appear to facilitate the production of HPQ with the requisite purities more easily, but costly equipment along with highly trained operators are required and hence unlikely to become available in standard metallurgical laboratories any time soon.

Sep 1, 2024

By Y Akiti, J Moller, E Esper, R Rugolo, A Pains

"Morro do Ouro Mine is a high tonnage/low-grade mine located in Paracatu, Minas Gerais State, Brazil. The mines move around 55 Mt of ore per year at an average grade of 0.4 g/t. The auriferous mineralisation of Morro do Ouro is related to hydrothermal fluids rich in arsenic (As), gold (Au), lead (Pb) and zinc (Zn). These percolated along favourable structures contained within phyllites of Upper Proterozoic age and defined a mineralised megaboudin which outcropped with 4 km extension and up to 2 km in width. The litologies in the interior of this structure are typically more deformed, sericitised and sulfidised, and exhibit the development of quartz boudins in the centre of the more deformed zones where are found the higher Au grades and the coarser sulfide crystals. Gold is preferentially associated with arsenopyrite, mainly occurring in fractures or aggregations of crystals and is rarely in solid solution or refractory. Over 90 per cent of the gold contained in the sulfide ore is free or extractable by cyanidisation. The current mineral reserve is 17.9 Mt at 0.403 g/t published at the end of 2012.In order to get a good grade estimation that represents the orebody more accurately a solids methodology was used to distinguish the different orebodies. Before 2011 the orebodies were worked with two domains relating to the weathered mantle. The B1 ore, which is oxidised, is located at the top of mineralisation, and is used to feed Plant 1. Underneath B2 ore, which is fresh sulfide bearing, represents over 30 years of production in Plant 2.In order to improve the predictability of gold grade estimation in geological modelling and to get a better predicting behaviour of each domain on the deposit, studies were carried out in which it was possible to show a correlation between elements and the mineralisation. One strong correlation and spatial distribution between Au and As, As and sulfur (S), Au and Pb, Au and Zn were found.Based on geochemistry, mineral correlations, amount of sulfide, structural deformation, texture of sulfides and the daily experience of the mine, it was possible to create solids that individualised bodies with similar mineralogical and chemical characteristics using the parameters listed above.After 2011, a new modelling concept was proposed and built with 11 different domains, compared with the previous, and with two more parameters: recovery acid neutralised capacity (ANC).Each of these bodies have different behaviours in mineral processing, like flotation and metallurgy. For example, bodies with pyrrhotite bring problems in the flotation, bodies with high arsenic do not recover well, bodies with high As with coarse texture have good recovery, bodies with fine texture do not have good adherence in production.In the present state of knowledge, protocols are being developed for bench testing to predict the recovery of each geochemical domain aiming to include these in the geological model for the parameter recovery. It is intended to create a field throughput in the model of ounces per hour, from each block of each domain to better predict the production, using the parameter recovery, Au and Bond Work Index (BWI).CITATION:Esper, E, Rugolo, R, Moller, J, Akiti, Y and Pains, A, 2013. Morro do Ouro geological model with a metallurgical view, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 67-74 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By S L. Nicol, B J. Hogg, O J. Mendoza, S Nikolic, A Burrows

The top submerged lance (TSL) technology, developed in the 1970s, is now widely used for the processing of a range of materials. The key advantage the ISASMELT™ TSL technology provided was the ability to process feed materials in a highly turbulent bath, reaching close to equilibrium conditions, uniquely allowing for operation below the liquidus of the molten slag phase. The details on what happened below the liquidus line in the phase diagram became critical for the successful operation of the technology. During the development of the ISASMELT™ technology this led to a collaboration between the Process Technology group of Mount Isa Mines, now part of Glencore Technology, and the Pyrometallurgy Research Centre (PYROSEARCH) at The University of Queensland. The fusion of the phase equilibria research into the technology development allowed for understanding of the behaviour of molten splash, reliable tapping of the furnace, and the ability to operate the furnace with a refractory lining and achieve a year campaign life in excess of four years. The outcome has allowed for the highly successful adaption of the ISASMELT™ technology to recycling of complex feed streams necessary to drive circularity in our modern global economy.

Aug 21, 2024

By J Player, G Sweby

The material properties and hence performance of saturated alluvial sediments slope can be incorrectly forecast if the water content is not preserved, and materials properties not correctly determined. The occurrence of saturated sediments in the Western Australia (WA) Goldfields, while not common, should be a significant investigation focus. Geotechnical engineers new to the area may be unaware of this and hence the importance of correct testing and determination of the material strength. Application of appropriate analysis to determine stable pit slopes to an acceptable level of risk, is not possible unless the appropriate strength and hydrogeological parameters have been established at the outset. A back analysis is presented of a pit that had extensive slope failures in alluvial clay-rich sediments with discussion on the approach adopted by the original design engineers to assess pit wall stability and consequent poor slope performance. Learnings from a full pit 3D back analysis are presented, with an approach to geotechnical and hydrogeological investigations and analysis for slopes in similar materials.

Jun 22, 2022

By Koch DFA

An electrochemical study of the dissolution of gold in aerated cyanide solution has shown that the dissolution rate is determined b the nature of the surface. A passive film (probably a basic cyanide formed at .o.6 V vs a saturated calomel electrode inhibits both the ca.thodi reduction of oxygen. Some aspects of these retction mechcnisms are discussed together with the-"activating" effect of Thpllium.

Jan 1, 1964

By Abdalla MH

The deformation resulting from the presence of a tunnel may signifcantly affected, nearby structures and need to be considered during design of both tunnel and structure. The aim of this paper is to study the effect of different factors which may affect the interaction between the tunnel and the str- ucture. These include; the depth of both tunnel and foundation level of the structure ( z and t ), distance between C.L. of tunnel and loads, breadth of the loaded area, Diameter of tunnel and lining of the tunnel. The problem is studied as a two dimensional plane strain model by the boundary element technique. The results of this study indicated that the presence of a cavity/tunnel increases, in general, the vertical displacement on the ground surface and at the foundation level as well as the horizontal and vertical stresses in the cavity/tunnel level. The effect of eccentricity is increasing as e/D decreasing. For pile foundation there is a quite different- influence of the presence of cavity/tunnel in both cases of friction pile and end bearing pile type of foundation.

Jan 1, 1987

The Callie Underground Gold Mine (Callie) is owned by Newmont Asia Pacific and located 531 km north-west of Alice Springs in the Northern Territory. Historically, stopes have been mined utilising a primary and secondary stoping sequence with cemented aggregate fill and rock fill respectively. Current and near-future mining will employ long hole open stoping with rib pillars and rock fill with a paste fill system approved to allow a higher extraction ratio from mid-2011. The Callie rock mass is of good quality with little or no mining difficulties during development and stoping to a depth of 1140 m below surface. Development is currently occurring at depth of 1360 m below surface. Stress damage previously observed only in secondary stope accesses is now observed in development unaffected by stoping stresses. A change in rock mass properties is being experienced with depth, with more pronounced and frequent joint planes. Also, other structures are intersected more commonly, such as lithological boundaries and fault zones. The 'Callie rock factory' mentality that has persisted for years is challenged. This paper covers an appraisal of the stress and ground condition changes at Callie. The appraisal outlines the mine design criterion that was developed and examines the transition from a low stress environment to one where stress damage is observed. Discussion includes a judgement on the rock mass damage observed in development, the dominant geotechnical factors influencing the change in ground conditions, and if a correlation can be made between the observed rock mass damage with stress through the use of numerical modelling.

Nov 25, 2010

By P Ramsaywok

The use of saline water for mineral beneficiation in arid regions is general practice and also the case with Exxaro Namakwa Sands, situated on the west coast of South Africa. Although it is ‘cost effective’ to use sea water for mineral beneficiation, downstream process separation efficiencies may be negatively affected. This is more specific to surface dependent separation techniques such as electrostatic and high tension (HT) separation. If minimal fresh water is available then, proper washing is often neglected. Salt crystals can form on particle surfaces during the drying process before electrostatic separation.This paper describes a study that has been conducted to determine the effect of upfront salt water processing on downstream electrostatic/HT separation. The study indicated that minor quantities of salt can cause the separation efficiency to decrease substantially.

Oct 5, 2011

By Y M. Wang, W Z. Liu, L F. Li, X L. Zhang

Based on the blasting crater theory, the equation between k under typical cases and burden line, charge height was obtained by open pit bench blasting analysis model. The model was calculated with mine production blasting. The blastability coefficient k and the best range of blasting burden line were specially emphasised on determination of lateral crater tests.CITATION:Wang, Y M, Liu, W Z, Zhang, X L and Li, L F, 2015. Application of lateral crater test in open pit blasting parameters optimisation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 463–468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By B J. Beven, A Vatandoost, J Young, S Campbell-Hardwick

The intrinsic value of iron ore depends on its physical and chemical characteristics. For example, silica and alumina are unwanted elements, downgrading iron grade and adversely affecting high temperature processing, attracting penalties in smelter contracts. For this reason, an informed knowledge of processing characteristics and product quality of the ore is valuable and cost effective during mine planning and processing.Ore variability is a significant factor that affects metallurgical behaviour and efficiency of ore processing equipment. Ore of sufficient chemical and physical quality needs to be modelled, mined, processed and usually blended. Feed and product assays are commonly used to assess potential ore upgradability. However, assays alone cannot be all informative of actual processing response given the variability of the physical properties of the ore.This study investigates the potential benefit of implementing a geometallurgical approach during the commissioning stage of the Kings deposit, part of the Solomon Iron Ore project in Western Australia. Kings drill hole database information, ie geological, textural and geochemical data, together with the results of metallurgical test work were used for geometallurgical analysis and modelling. Three main ore types were identified at Kings, namely channel iron deposit (CID), bedded iron deposits (BID) and Detrital Iron Deposit (DID). Additional classifications were utilised to better characterise these units in terms of their physical properties.Bulk sampling for each ore type was carried out across the deposit for metallurgical testing. Multivariate statistical models were developed for prediction of product quality for each geometallurgical unit. A new approach for modelling yield based on ore upgrade factors is introduced. These models were then applied to the Kings regularised mining model to assess product quality across the mining blocks and to plan product stockpiling and blending strategies.CITATION:Vatandoost, A, Beven, B J, Campbell-Hardwick, S and Young, J, 2013. A geometallurgical approach for iron ore product evaluation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By M Recabarren, A Echeverria, J Ronda, J I. Guzman, R Dodds, G Juarez, E Vila-Echague

A strategic mine plan is a fundamental part of any mining operation. It must provide a realistic and operative extraction and processing schedule, and yield the highest value for the business. For open pit mines, the problem can be modelled as a set of blocks representing the deposit, for each of which we need to decide if it is going to be mined, if so, when and where it will be sent (process, stock or dump).This problem can be proven to be of NP-Hard complexity. The traditional approach used by mining engineers to tackle this complexity is to separate the problem into more tractable components, solving each separately. The first step is to use the Lerchs-Grossman (LG) algorithm to obtain the final pit limit, as well as a set of optimised pit shells (nested pits), using different input prices. Then, using this input, operational phases are designed. Third, the set of phases can be used as an input for a phase-bench style optimisation, usually using a mathematical programming-based algorithm.There are, however, several problems with this approach. First, dividing the problem into simpler parts has the consequence that any compromises made at early stages limit the potential value left for the following steps. Second, LG is a static algorithm, with no concept of the time-value of money, capacity limits, opportunity costs, etc. Phase design is essentially a manual step, for which nested pits provide insufficient information in practice, and therefore the quality of the result in terms of potential net present value (NPV) depends strongly on the experience and expertise of the designer. This means that key input data such as commodity prices, different processes capacities and mine movement limits, are considered only at scheduling, when there is little room for optimisation. This sequential approach limits the potential value in each step, where a simplified problem is addressed, instead of addressing the real, and more complex problem, which is dynamic and should be solved as a whole.We present in this paper an algorithm, and its commercial software implementation, that addresses the dynamic problem as a whole, simultaneously and automatically creating a high-value strategic mine plan that adheres to basic operational constraints, determining dynamic cut-off grades and delivering a set of phases which can serve as a much stronger guide than nested pits for the final design. We discuss some of the key elements of the algorithm and propose a new methodology for strategic mine planning, where phase design dynamically responds to mining strategy definition. Results using different mining and operational parameters on a fictitious copper deposit are used as a demonstrative example.CITATION:Juarez, G, Dodds, R, Echeverria, A, Guzman, J I, Recabarren, M, Ronda, J and Vila-Echague, E, 2014. Open pit strategic mine planning with automatic phase generation, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 147–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Kendall W. T C

This paper provides a brief overview of the history of the Chaffers Dewatering Project which was successfully commissioned in August 1993. Until the end of 1992 the `Superpit' and the deep mines of the Golden Mile had all been dewatered by a staged pumping system from the 28 level in the Lake View Shaft, which was removed at that time when the Lake View Mine was absorbed into the Superpit. Feasibility analysis had indicated that adaptation of oil industry technology offered the greatest potential for a low cost solution to the problem of dewatering the open pit and deep mines. A KCGM engineer and one of the authors visited the Jackson oilfields to look at the deep well pumping technology in use there in early-1991. In the final analysis a new dewatering station was established in the 23 level crushing station of the Chaffers Shaft using conventional plunger pumps, but the rising main was screwed 178 mm OD (7 inch) casing the suspended from the surface to a depth of 686 metres, and was installed using oilfield personnel and methods. Only the second installation of its kind in Australia, the project achieved the dewatering objective at about half of the capital cost of the more conventional approach and at lower operating costs as well.

Jan 1, 1995

By P Holtham, K Duffy, L Pyle, W Valery

The mining industry is becoming increasingly focused on pre-concentration due to its potential economic and environmental benefits, particularly for the more complex, low-grade, high throughput operations now being developed. Advances in technology have seen bulk ore sorting (BOS) trialled at several operations. However, BOS should not be seen as a ‘silver bullet’, it can offer significant benefits, but only under the right conditions. Deposits with interspersed mineralogy or disseminated, fine-grained minerals can be difficult for BOS. Large batches of barren or low-grade material are required for BOS to be effective. Hatch has recently completed several studies for clients who believed that bulk sorting was the most suitable pre-concentration technique for their operation, based only on an assumed sorter recovery or on laboratory trials of the chosen sensor. However, minimal consideration had been given to the heterogeneity of the deposit, the achievable separation batch size or sensor repeatability. Evaluation of BOS needs to consider both heterogeneity and sensor suitability. The valuable or gangue mineral must be present in such a way that it can be separated effectively in the large bulk sorting batch sizes, without competing minerals or changing ore characteristics affecting the metal upgrade or recovery. Also, the sensor chosen must be able to detect either the valuable mineral, a proxy for the valuable mineral, or a gangue mineral for rejection with sufficient accuracy and precision (repeatability). This paper presents three recent case studies, emphasizing markers which indicated that bulk sorting was unsuitable for the project whilst highlighting the pre-concentration technologies which were applicable (including particle sorting, and coarse particle gravity separation). The modelling methodology, equipment sizing and forward work plans developed to verify these alternative solutions are also presented, demonstrating the key factors contributing to a thorough scoping assessment.

Aug 24, 2022

The Great lady gold deposit presented the challenge of providing a new grade control system for an usual type of orebody in the Eastern Goldfields. Mineralisation occurs as secondary enrichment about a quartz sand - granite saprolite contact 30m below surface. The ore horizon, which averaged 2.5m thickness, was near-horizontally disposed in contrast to the typical steeply dipping, shear hosted deposits of the region. A trial mining operation was undertaken on the richest, most continuous portion of the deposit to test the economic viability of this type of orebody. Controlling and minimising vertical ore dilution was considered crucial to the profitability of the operation.An understanding of the grade distribution combined with the practicalities of mining produced a grade control system which allowed for the mining of 1/2rn composited grades on level lm benches. Ore mining was combined with strict monitoring of levels, truck destinations and ore boundaries. Ore reconciliation results showed this system to be effective.

Jan 1, 1990

By I Ritchie, G Lane, C Morley, D Yataco

Marcobre SAC (Marcobre) is developing the Mina Justa project in Peru. The project has a lower grade oxide orebody overlaying the higher grade sulfide orebody. The oxide ore is treated by acid leaching; consumption of acid is high and is managed by vat leaching rather than the more conventional heap leaching process.The leaching process uses ore crushed to 100% passing 8 mm to optimise copper recovery. Acid consumption generally increases with a higher proportion of fines. Marcobre is investigating a three-stage crushing circuit with high pressure grinding rolls (HPGR) in the third stage, instead of the more conventional four-stage cone crushing circuit. The use of HPGR can result in higher fines production due to the higher compression forces in the crushing zone. This paper reports on the outcomes of the test work completed by Marcobre in 2016 and 2017 to manage fines production and compare the use of HPGR with conventional crushing on a high acid consuming ore.At moderate pressing forces, a HPGR crushing circuit appeared to produce similar size distributions to cone crushing. On average, both the copper recovery and the acid consumption in subsequent vat leaching were higher with HPGR crushing than with cone crushing.CITATION:Lane, G, Morley, C, Yataco, D and Ritchie, I, 2017. Are there differences in size distribution when comparing conventional crushing and HPGR?, in Proceedings MetPlant 2017, pp 60–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Ellery B. I

Field investigations recently undertaken by Utah Development Company (U.D.C.) have been developed to allow the assessment of ground conditions relevant to the use of large bucket wheel excavators for pre-stripping overburden. "Bucketwheel diggability" predictions were made on the basis of a wedge test which was perform- -ed in the field on nominal 150 mm diameter drill core samples. Specific separation force (calculated from the wedge test results) for different rock horizons were theoretically related to the excavation rates of various sized bucketwheels, i.e., "bucketwheel diggability". The specific separation force was shown to vary with lithology, structure, weathering and moisture changes. By correlating these features between boreholes, an overall assessment of bucketwheel diggability was then made. The approach adopted to assess bucket- wheel diggability incorporated various levels of investigation. Initially, a reconnaissance stage provided information from widely spaced 150 mm cored holes to compare and contrast areas with differing bucketwheel digging char- -acteristics. The following stages progressive -ly added to this information, until finally, between hole correlations, allowed calculations to be made of volumes of materials of similar

Jan 1, 1981

By Baxter D. A

This paper, one of two written about the Queensland Railways Brunswick Street tunnels presented at the VIII Australian Tunnelling Conference, 1993, describes the design and monitoring aspects of the railway tunnels built between Central Station and Brunswick Street Station.The design was mainly influenced by the need to minimise settlement of buildings above the route. The performance of the design details and the monitoring of the tunnels are briefly described.Appendices include extensions to the work of Curtis in the analysis of circular tunnels in a viscoelastic ground.Reference: Asche, H R and Baxter, D A, 1993. Design and ground support monitoring of the Brunwick Street rail tunnels, Brisbane, VIII Australian Tunnelling Conference.

Jan 1, 1993

By Cox N

Fragmentation control is perhaps the most critical aspect of quarrying operations, potentially impacting on the costs of all down stream processes, and sometimes even on the economic viability of an operation. The focal points of studies to control fragmentation are generally the pattern of blastholes, the accuracy of drilling, and the most appropriate powder factor. Recent studies suggest that the performance, and consistency of performance, of explosive detonation in the blastholes may also be a significant factor impacting on blast performance in hard rock quarries. This paper presents the results of studies of bulk emulsion and watergel explosive performance, using blasthole velocity of detonation measurements, and its impact on fragmentation. Field studies show a strong correlation between blasthole VoD and blast fragmentation. Another aspect of explosive performance impacting on ease of excavation of blasted rock is muckpile displacement, from which estimates of effective heave energy have been made for different bulk slurry (emulsion and watergel) products.

Jan 1, 1995