Search Documents

By Smith R. N

The Olympic Dam copper-uranium-gold-silver deposit is located approximately 520km north-northwest of Adelaide, South Australia. The deposit was discovered in 1975 by the Exploration Division of Western Mining Corporation (WMC). A joint venture, to facilitate development of the deposit was formed in mid 1979 between WMC (51%) and the British Petroleum Group (BP) (49%).

Jan 1, 1990

By Jones IO

Although small units have been in use formany years, particularly in opal mining at shallow depths, there has been little effort in the past to explore the potential of the vacuum lift system in other more demanding applications. Recent developments in Western Australia by a small number of mining companies, contractors and manufacturers have seen the design and construction of several larger, more powerful units for use in winzing, shaft sinking, hoisting and spillage removal. Some of these units have proved very successful and suggest that they could be developed for a wider range of applications and duties in future.

Jan 1, 1984

A new least-squares method for inversion of d.c. resistivity soundings from horizontally layered earth is proposed. Powers are used as measured data. Apparent resistivity is generalized and apparent parameters curves are defined. Estimates for parameter errors are often possible even when data errors are unknown or large. Acceptance or rejection of a model is made an easier decision. Total computational effort is often reduced when compared to global least-squares methods, because although several optimizations are needed, few data points are involved in each, and initial guesses are requested only once and not all at the same time. Correlations between parameters may be used to improve solutions. Precise indications for extra needed data points can be conveyed. A test example is worked out and a field sounding, taken by Rijo (1973, personal communication) in an alluvium-filled river valley in north-eastern Brazil, is studied.

Jan 1, 1987

Cable bolts are being used more extensively by the mining industry for many different rock reinforcement applications. The configuration of these bolts has evolved over the last 20 years to meet the immediate needs of industry at the particular time. Most improvements to date have focussed on increasing the mechanical performance with little attention given to issues such as ease of handling, matching response to that of the rock mass or corrosion protection. Ultrastrand has been designed and being developed with this broad perspective in mind so that it will satisfy the ground reinforcement needs of today's and tomorrow's mining industry.Laboratory tests on Ultrastrand prototypes have confirmed that mechanical performance is superior or equivalent to Standard and Birdcage Strand respectively. Preliminary discussions have been held with an installation equipment manufacturer with a view to conducting a trial at a mine site by early-1992.

Jan 1, 1992

By Kurzeme M, Willoughby D. R

The current approach to the design of fill, as a structural component in a mining system, is based on traditional usage, previous experience, empirical rules and preconceived ideas. This approach does not permit the relative economicsof the various possibilities to be evaluated, retards introduction of new materials or processes, and results in fragmented fill research effort.A rational approach to the design of fill is proposed as a means of overcoming these disadvantages.This is based on five components:(a) statement of functions of fill,(b) definition of modes of fill response,(c) criteria of satisfactory performance,(d) analysis of fill response,(e) specification of required fill properties and methods of obtaining them.An assessment of each component indicates that the adoption of this rational design approach will require research effort in categorising modes of fill response and in defining criteria of satisfactory performance.

Jan 1, 1973

By Svenson D

For fully effective information to be obtained from exploratory drilling for coal, drilling programs should be planned systemati- cally in successive stages, on the basis of existing geological criteria and information collated during each stage. In this way, drilling can be executed with optimum economy, aided by auxiliary geophysical techniques wherever these may be appropriate. The object- ives of the programs must ultimately include an adequate assessment of mining conditions as well as thorough evaluation of coal quality. The first of these objectives is not always appreciated by both geologists and mining engineers engaged in supervising drilling pro- grams, often resulting in the need for more additional drilling and more expense than would otherwise be required. To achieve all of these objectives as effectively as possible, the drilling should be supervised by well qualified personnel experienced in working in a multi- dicipline, professional mining, geological and engineering team.

Jan 1, 1977

By Y S. Zhang

Natural phenomena and human engineering construction activities had great influence on the geosciences space. Natural disasters, particularly mine disaster and other geological disasters happened frequently, which brought great losses both in people’s lives and economics, therefore, to explore the essential causes and mechanisms of disaster by some useful approaches is the most important step in mine disaster prevention. In a variety of methods, building an aground-underground seamlessly integrated model, and then analysing the formation and development mechanism of mining disaster based on this model is a useful way. In this paper, we studied an aground-underground seamlessly Integrated modelling method, and correspondingly given an aground-underground seamlessly integrated 3D spatial model, CSG+CD-TIN+GTP-TTS, by which we can carry out analysis of surface subsidence and underground laneway distortion efficiently, finally preliminary applications verified the effectiveness of this method.

Nov 22, 2011

By McDonough RJ

Mechanical agitation is the preferred system for Carbon-in-Pulp processes. Agitator design requires an understanding of the relationships between energy, shear and flow and the nature of shear rates and shear stress distribution in an agitated tank. Laser techniques are useful when studying these phenomena. The alternatives are open impeller agitation or draft tube circulation. Each has advantages and disadvantages but both require careful choice of impeller and system geometry. Overall the draft tube circulator is the more attractive in many cases. Open impeller agitators are designed in accordance with established procedures for mineral slurries taking due account of shear effects in tanks containing carbon. Preferred tank proportions are 1:1. Circulator design methods were developed in the alumina industry before being applied to CIP processes. Optimum draft tube diameter is critical to power requirements. The overall system must be designed as an axial flow pump operating in a closed circuit. Such a system exhibits quite characteristic behaviour which requires an impeller of varying pitch angle and aerofoil section for best stability and efficiency.' Tank height may be 2 or more times diameter. Resuspension of settled solids can be assisted by a series of slots in the draft tube. These slots have the secondary effect of stabilizing hydraulic behaviour and reducing installed power requirements.

Jan 1, 1982

The investigations described in this paper aim at the development of a new impact mill. The objective is to produce particle size distributions below 10 .tm without using an air classifier. Circumferential rotor speeds of up to 200 m/s are strived for.

Jan 1, 1993

By E Nunes, R Mendes, D Jacobson, G Cota, T Machado, E Santos, J Almeida, E Pereira9, B Raso

Grinding circuits are known to be the highest consumer of energy used in the ore comminution process, with high operational costs and sensitivity to ore conditions. The mining industry is being encouraged to look for more energy efficient processes while increasing the mass and metallurgical recovery; a specific example is projects with lower iron ore grades, which demands a higher level of liberation and resulting higher energy consumption. This has led to increased usage of high-pressure grinding roll (HPGR) technology as an alternative design within the comminution circuit. A growing use of the HRC™ HPGR technology has been used to generate concentrate through a more sustainable process. In the Brazilian state of Minas Gerais, the readaptation of iron ore beneficiation circuits has been initiated, replacing the traditional crushing-to-grinding flow sheet with circuits using crushing-to-HPGR flow sheets, with the main driver being reduced energy consumption. Utilising results from sampling campaigns and analysis of experimental data collected in an industrial plant, the work herein presents a case study from the JMN Mineração operating plant, where the HRC™ HPGR was used as an alternative to traditional grinding using horizontal mills. The results show that the HRC™ HPGR performance in this iron ore processing plant showed benefits in terms of reduced energy consumption as compared to the projected performance with a traditional grinding circuit.

Sep 18, 2023

Ulan Coal Mines Limited operates an underground and open cut mine near Mudgee in the Central West of NSW. The mines are part of a Joint Venture managed by Exxon Coal and Minerals Australia Limited (ECMAL). Currently all the mines output of over five million tonnes per annum is sold into the export market predominantly as a steaming product.

Jan 1, 1993

Since its beginning, with the works of D. Krige and later, G. Matheron, geostatistics has been analyzing in detail the essential factors at play in ore reserves estimation problems, with the ever-present aim of an optimal use of the available information. Not only do the reserves depend on the geological in situ resources, they also require a correct appraisal of many technical and economical parameters. The objective of the present paper is to show how the method of technical parameterization of reserves, which is at the heart of the geostatistical approach, provides an extremely powerful and versatile tool for characterizing a mining project. After a review of the main properties of the technique, its use in the economic optimization of a project will be examined. Two examples from copper and gold deposits will be given.

Jan 1, 1987

By Szymanski J, Planeta S

For many hard rock mines with near surface deposits, the surface crown pillars form the first line of protection for the immediate underground workings. Underground stopes are typically contained by crown pillar, which protects the level above, rib pillars, and a sill pillar through which the ore collection system is cut. This paper discusses the mining of these pillars, with particular emphasis on the overall stability of the mined out upper part of the mine areas. An area of interest is located in the Canadian Shield, where the mining has progressed below four thousand foot level in the ultramafic high grade sulphide type of orebody.

Jan 1, 1995

By Baafi E. Y

A heuristic approach for the optimisation of the stope geometry is presented. The heuristic method uses economic model of a given deposit to search for the best combination of mining blocks that results in the maximum profit while imposing geo

Jan 1, 1998

By Propster M, Choudhry M

THIS note gives comments on the paper by Kitaev et al on p. 68 of this book and compares results with those obtained by ourselves. We wish to say that the authors are to be congratulated on their sophisticated approach to an important problem and that it complements our efforts on flow maldistribution.1-5 It is our view that Eqs. (1)-(5) on p. 69 are impressive, but unfortunately with present day computers and computational facilities, it would be quite impractical to contemplate the numerical solution of these. Eq. (8) in the authors' paper, on p. 70, does provide the logical starting point for tackling flow maldistribution problems and strictly speaking this equation is more accurate than Eq. (1) in our paper in this book. We note in passing that there is direct experimental evidence to support the contention that our Eq. (1) is at least a reasonable approximation and one may question in a practical sense whether the refinement afforded by Eq. (8) in the paper by Kitaev et a/ is justified. While one must readily accept the appropriateness of Eq. (8) of Kitaev et al as a starting point, the subsequent mathematical manipulation by the authors is open to serious criticism. In order to solve this complex, non-linear equation Kitaev et al postulated irrotational flow, which afforded considerable simplification. One can argue simply on physical grounds that the assumption of irrotational flow is inappropriate, a fact which should be readily apparent on inspection of the flow fields shown in Figs. 2 and 3 of Kitaev's paper. It follows that while the starting point through the use of Eq. (8) is correct the results derived from this starting point may be suspect because of the erroneous nature of the irrotational flow assumption.

Jan 1, 1975

A model has been developed for the per iodical maintenance of bins used for hydraulic hoisting in mining of steeply inclining coal seams. This model gives a control plan for hoisting, bin switching and bin maintenance on a regular schedule.

Jan 1, 1977

The Newmont Waihi Operations are centred on the Martha mine at Waihi, New Zealand. The mine has produced over 6.6 million ounces of gold from both openpit and underground sources since operations began in 1878. The current open pit operations commenced in 1988 and in the year to 30 June 2002 produced 129,790 ounces of gold at a cash cost of USD122 per ounce. This paper provides an overview of current operations and future directions.

Jan 1, 2002

Historic mining across the Bendigo goldfield reached an average mining depth of 750 m over an area of about 16 km by 4 km, with two shafts exceeding 1400 m. Mining ceased in the mid 1900s due in part to increased dewatering and ventilation demands. Water extraction technology of the day, combined with multiple mine ownership, did not allow uninterrupted and thus economic mining activity to prosper. Today Bendigo Mining Limited (BML) is targeting gold-bearing reefs beneath the water-filled historic mine workings. To ensure mining activity can proceed without the risk of water inrush, historic workings are being dewatered by submersible pumps in historic shafts and through a series of underground drain holes intersecting old workings. Due to the high heads involved, individual drain hole development requires rigorous safety control implementation and assessment prior to drilling. Water extracted via drain holes is pumped to the surface through a series of pipe lines and rising mains in conjunction with two staged pumping stations. Both stations are equipped with high-speed centrifugal pumps, each capable of pumping 40 L/s at a static head of approximately 300 m. BML, which operates beneath and within a large city, is confronted with unusual environmental and social challenges compared to many within the mining industry. The raw mine water, which contains elevated salt levels, is piped through residential areas and must comply with strict controls to prevent impacts on the surrounding environment. The final delivery point is BMLÆs water treatment plant at the north end of the city. The water treatment plant utilises chemical pretreatment and reverse osmosis. It is able to process 7 ML of mine water per day at full production. The product is approximately 5 ML of reusable irrigation quality water, which is made available to the Bendigo community for public gardens, sporting facilities and rural irrigation. The 2 ML of brine is directed to a purpose-built evaporation pond facility located 7 km north of the water treatment facility.

Jan 1, 2008

By L Cooper, J Sharma, M J. Hendry

Thick clay tills below potash mine tailings and brine ponds are important natural barriers protecting fresh water aquifers in Saskatchewan. Centrifuge modelling was applied to assess geochemical processes and impacts of dilute brine (0.1 M NaCl) migration through clay till core samples obtained from non saline, unoxidised clay till at a mine site. At accelerated gravity of 876 + g, during each day of centrifuge modelling, flow driven through a 52 mm length core simulated transport through a 45 m thick clay over ~2100 years. Hydraulic conductivity, monitored continuously before and during brine permeation, was low and relatively constant (8.5 + 10-12 m/s), confirming that confining stresses prevent permeability increase. Core density and porosity measurements confirmed that reactive transport occurred under realistic in situ conditions. Breakthrough (defined by C/C0 = 0.5) of non-reactive Cl- occurred at 25 days. The slight delay for Na+ breakthrough, associated with small increases in Ca2+ and Mg2+ concentrations in the effluent were attributed to ion exchange, but carbonate reactions were relatively unimportant. Cation exchange analysis of core samples was inconclusive without corrections for porewater Na+ and carbonate dissolution. Geochemical processes that were observed during centrifuge modelling were successfully simulated using the 1D geochemical transport code PHREEQC. Solute transport was dominated by diffusion with limited ion exchange to delay Na+ migration. Brine would not break through a 45 m thick clay for tens of thousands of years. Based on these findings, the thick clay till at this site, if laterally extensive and undisturbed by drilling activity, is likely to act as an effective natural barrier to vertical brine migration over the long term.

Jan 1, 2003

By J Sigda, T Jones, D Staggs, J Ewing, C Cheng, J Pickens, S Paulka

Mine-derived solutes from Energy Resources of Australia’s (ERA’s) Ranger uranium mine have been closely monitored for decades. Ranger is surrounded by the Northern Territory’s Kakadu National Park and is upstream of Ramsar convention wetlands. Modelling of groundwater flow and solute egress from mine wastes to surface waters has helped ERA successfully assess closure options and secure intermediate regulatory approvals during the site closure process. Potential environmental impacts were assessed using groundwater modelling in support of three ERA applications involving disposal of tailings-derived mine waste. Model results were an important part of the basis for obtaining regulatory approval. Three case studies are presented describing the three applications and how the groundwater modelling supported approval of the applications. For case study #1, INTERA supported ERA in addressing stakeholder concerns in 2017 regarding two aspects of tailings deposition in Pit 3. The first was the potential for flow of tailings fluid into the surrounding formations during tailings deposition. The second was the difference in post-closure magnesium (Mg) loading to surface water for two tailings deposition scenarios. INTERA developed a two-dimensional (2D) model that showed excess tailings pore pressures would not cause outflow and solute egress from the pit during deposition. INTERA’s three-dimensional (3D) models demonstrated that post-closure Mg loading to creeks for both tailings scenarios differed marginally and would be a small fraction of natural creek Mg loads. The modelling results helped avoid delays in completing tailings deposition driven by stakeholders’ environmental concerns. Case study #2 consisted of supporting ERA’s 2019 request for approval to change the tailings deposition method and final tailings level in Pit 3. INTERA’s model results for the permitted and proposed deposition methods showed minimal differences in post-closure Mg loading to creeks. The model results helped ERA obtain the needed approval for the tailings deposition method and water and tailings levels in Pit 3. For case study #3, INTERA modelled the comparative impacts from leaving the entire contaminant plume from the temporary tailings storage facility (TSF) in situ or excavating a portion of the contaminated material from beneath the TSF floor and placing it in Pit 3. The modelling results supported an approved TSF contaminated material application important for ERA to stay on schedule and minimise both closure costs and environmental impacts.

Jul 1, 2021