Search Documents

Magnetic separation using particle rotation in a continuously rotating magnetic field offers very low to insignificant non-magnetic particle entrapment, and precise magnetic fractions. The precision of rotating magnetic field separations makes the method ideal for dry laboratory magnetic analysis work, where conventional laboratory magnetic separators can give misleading or uncertain data. The very low entrapment characteristics make the method ideal for entrapment-critical separations within the diamond exploration industry or in gold recovery. A single wet rotating magnetic field (RMF) unit is able to achieve a cleaner separation (at similar or better recovery rates) than a three-stage separation using conventional wet drum separators. The RMF separator is able to work effectively at particle sizes below 50 ¦m, and RMF separation could, at least in theory, be used down to single domain particle sizes. Rotating magnetic field (RMF) separation is carried out by magnetically spinning the particles at frequencies up to 300 Hz. The particle rotation itself may be used to roll the particles out of the separator. At angular velocities of 100 Hz, magnetic flocs are unable to form, and any entrapped particles are energetically expelled. In an RMF separator, the outer drum can be stationary while the inner magnet rotor rotates, allowing, for example, the injection of cleaning water underneath the separating magnetics to help remove small suspended non-magnetic particles.

Jan 1, 2000

By Szymanski J

In the first part of this paper, the principal sources of dilution during underground evaluation and mining are discussed, then definitions of ore dilution currently in use are analysed. These definitions vary depending on the authors. Ten different analytical expressions of dilution percentage currently exist. It is demonstrated, with the help of a numerical example for a given mining condition, that dilution percentage results vary considerably and that they depend on the definition used. This situation makes it difficult to compare different results regarding the dilution problem, often because some of the terms used are contradictory. A new ore dilution evaluation methodology is proposed, replacing the ten different analytical expressions by only two: the planned dilution factor related to the stoping selectivity, done at the mine planning level, and the additional dilution factor related to the efficiency of the dilution control measures during stoping operations. The conclusion shows that the use of this methodology would be a definitive asset in planning, in stoping operations follow-up, and in future costs comparison studies between mining operations.

Jan 1, 1995

By Wu Y. H, Lu J. P

Slope stability has now become a practical tool in the design and oper- ation of open pits. The stability of rock slope depends on many factors, including not only structural geology, the existence of weak layers, ground- water, blasting and weathering, but also the virgin stress field. This paper presents an application of a numerical method to investigate the effect of the virgin stress on slope stability. The finite element method is employed to simulate the excavation of open pits. Redistributed stress fields in the slope of open pit are computed for several different virgin stress fields. Based on the redistributed stress fields, the shear force which tends to produce sliding of a rock mass and the frictional resistance to sliding are evaluated. The possibility of potential failure is assessed by the limit equilibrium method. The combination of the finite element method with the equilibrium method provides a powerful analytical tool for slope stability. The significant effect of virgin stress on the stability of slopes is shown by studying a typical case.

Jan 1, 1989

By Denholm W. T

The SMELT-2 package is specifically designed to perform on-line simulation of smelting processes. This paper describes its application to the simulation of continuous matte converting followed by reductive slag cleaning in SIROSMELT reactors. The matte, containing 50% Cu is assumed to be produced at the rate of 20 tph in a continuous matte smelting furnace such as an Outokumpu Flash Furnace, Noranda or Sirosmelt reactor. Two alternative fluxing strategies in the converter are examined, namely: ò conventional silicate slags, ò calcium ferrite slags, and the flow sheets associated with each strategy are discussed. A regular solution model is used in the present study to account for the variations in the activity coefficients of components in the slag.

Jan 1, 1989

Despite the research interest on non-cyanide gold lixiviants over the past three decades all the non-cyanide gold processes are still at the developmental stages with limited understanding on solution and pulp chemistry in some cases. This is partly associated with:the difficulties in measuring reliable equilibrium data for various gold(I/III) complexes with non-cyanide ligands; the lack of knowledge on mixed-ligand complexes; and different kinetic stabilities of gold(I) complexes with respect to disproportionation. This paper presents reliable equilibrium data for complex formation, dissolution, precipitation, hydrolysis and disproportionation reactions of gold(I/III) compounds with a range of non-cyanide ligands: S2-, HS-, S2O32-, SO32-, SCN-, SC(NH2)2, OH-, NH3, Cl-. Solubility of gold(III) compounds with non-cyanide ligands follows the order: Cl- > NH3 > OH-. In the case of gold metal the solubility order at a given temperature is MgS > Fe(III) or Cu(II) / Cl- > Cu(II)/NH3 > NaOH, but the solubility increases with increasing temperature. Rate of gold oxidation with different non-cyanide lixiviants depends on the oxidant, ligand and temperature and follows the general order of oxidants: Fe(III) or Cu(II) > X2 or OX- > O2 (X = halogen). In the case of metal ion oxidants oxygen is required to reoxidise Cu(I) or Fe(II). Some of the reported data on chloride and thiosulfate leaching of gold are presented to highlight the effect of additives and the copper, silver and sulfur contents of the starting material on the success of non-cyanide leaching processes.

Jan 1, 2004

By Thomas CG, Armstrong GJ, Lynch KS

A small glass walled pot grate has been used to simulate drying of iron ore pellets in a travelling grate plant. This equipment has enabled the effect of decreasing grind and de- creasing pellet bulk density on plant production to be quantitatively predicted. These predic- tions are compared with plant experience. The use of the laboratory simulator in comparing the effect of various additives on plant production is also described and substantial improvements in both the goethite and free-water drying periods are predicted.

Jan 1, 1972

By C Morley, B Costello

In 2002 the Argyle Diamond Mine upgraded the process plantÆs recrush circuit to include a High Pressure Grinding Roll (HPGR), or High Pressure Rolls Crushers (HPRC) as they are termed in the diamond industry. HPGR have generated considerable interest over the last decade, though there are still technical/processing unknowns to its effectiveness as a primary diamond ore crusher.The upgrade of the Recrush circuit at Argyle Diamonds has gone a long way to answering some of the key questions, and thus it has reduced the unknowns to a level more acceptable to the industry.This paper focuses on the results from the HPRC at Argyle, in particular the performance of the studded wear surfaces, comparison of energy efficiency against traditional quaternary cone crushers and the resultant increased liberation. Issues that have arisen, including edge wear of the studded surfaces, will be discussed and the steps taken to reduce this issue are presented.

Jan 1, 2004

By Myers I. A, Peters S. G, Bultitude R. J, Dowling K

Gold-quartz and antimony-gold-quartz veins in the Hodgkinson Province are hosted by subgreenschist to greenschist facies metasediments and show no spatial association with granitic rocks. They commonly parallel axial plane foliations or occur in brittle to brittle-ductile shear zones. Detailed mapping in the Hodgkinson goldfield indicates that vein systems are isolated in distinct structural and lithologic domains by post-mineralization faulting. Gold-quartz and antimony-gold-quartz veins have distinctive mesoscopic textures characteristic of the mesothermal vein environment. Some of the antimony-gold-quartz veins are located on domain boundaries which truncate the gold mineralization. In. some areas, tin and tungsten-tin mineralization which are spatially related to Late Palaeozoic granitoids appear to postdate the gold-quartz and antimony-gold-quartz mineralization.Oxygen and hydrogen isotopic studies of vein and alteration assemblages associated with these diverse ores provide constraints on fluid sources and have implications for the origin of mesothermal gold mineralization. The available isotopic data are consistent with a dominantly magmatic source for tin and tungsten-tin mineralization although there is evidence of a late-stage meteoric component in some tin-mineralizing systems. Although a distal magmatic contribution cannot be entirely discounted, the gold-quartz and antimony-gold-quartz veins were probably deposited from deeply

Jan 1, 1990

The first hydraulic roof supports were installed underground in 1950s and ever since that time engineering developments have improved the supports in many different ways. However. advances in three main areas, the roof support mechanical design, hydraulic engineering and electronics have ultimately led to the point where, 35 years after that first installation. automation has been achieved and is now commonplace.The history of roof support automation has involved the continual integration of high technology engineering. Thera ate further possibilities for the future which combine to give some idea of the likelihood of there ultimately being a completely manless face.

Jan 1, 1991

By Smith Z, Huppert P, Charbucinski J

The paper describes a spectrometric method and apparatus developed for lithology logging in brown coal formations. The nuclear spectromet- ric technique developed is able to delineate coal/sand/clay seams. One requirement was to log inside drilling rods, as well as cased or open holes. The method described is based on combined natural gamma and gamma- gamma techniques using a spectrometric system for signal acquisition and subsequent computer based on-line data analysis and interpretation.

Jan 1, 1989

Quite often the reserve assessor becomes enamored with the numbers gen- erated and forgets the basis for his assessment. The quality of the assess- ment can only be as good as the quality of the input data. The use of seismic data from the Gippsland Basin in assess- ing Esso/BHP's oil and gas reserves is an excellent example of this principle. By significantly improving the quality of seismic data, a much more reliable estimate of a field's reserve potential can be made. In addition, it provides the basis for further delineation drill- ing which, as recent experience in Gippsland has shown, often leads to increased reserves.

Jan 1, 1979

By Cudmore JF, Rowlands D

Incidents associated with spontaneous combustion of coal have resulted in the loss of many lives and considerable capital and equip- ment. Nevertheless, the factors controlling the propensity of coal to spontaneous combustion are not clearly understood and there is a need for research to study the effects of rank, petrog- raphy, moisture contents, etc. This has been attempted in a study of the propensities of selected Queensland coals to spontaneous combustion. An adiabatic calori- meter was constructed to study the self-heating of a large number of coals. Chemical and petro- graphic analyses of the coals were determined and an attempt was made to relate these propert- ies to the self-heating characteristics of the coal. The results show a strong relationship between rank and self-heating characteristics and that petrographic composition of coal may also be of importance. Some observations on the application of the laboratory results to the practical situation are made as are recommendations for future research.

Jan 1, 1981

The Electrolytic Refining and Smelting Company of Australia Limited (ER&S) operates a copper smelting and refining plant and is situated close to the heart of the highly industrialised area of Port Kembla. In March, 1982 the Company entered into an undertaking with the State Pollution Control Commission (SPCC) to monitor ambient levels of sulphur dioxide (S02) gases present in the atmosphere in the surrounding urban area. Despite the use of a 200 metre high stack for dispersal of the smelter waste gas stream at ER&S, two local suburbs, Warrawong and Primbee were experiencing on occasions high ambient concentrations of S02 resulting in discomfort to local residents. In late March 1982, ER&S installed a highly advanced S02 monitoring system to continuously monitor the levels at Warrawong. The system was extended to include S02 monitoring at Primbee in November 1982, and further extended in June 1983, to include an input of meteorological data. Initially the system was designed to monitor and react to high concentrations of S02 at either of the two monitoring stations. Currently however, refinement is taking place to allow a predictive nature to be built into the system such that it not only reacts to an adverse situation but can predict weather patterns likely to cause high concentrations and thus avoid these events. The entire system is still undergoing a growth and development period, however the results obtained to date are pleasing to both the Company and the SPCC.

Jan 1, 1984

By Trueman R

If continuous mining systems are to be successfully applied in metalliferous mines then reliable models will be needed to predict rock cutting machine advance and tool wear rates for effective machine selection before mining commences. Many of the predictive models developed to assess cuttability in situ are over-simplistic. As a result they tend to be both site and/or machine specific. Nevertheless very detailed models have been developed for full face machines which are capable of accurate cuttability predictions in a variety of rock mass conditions and for a variety of machine and tool configurations. However, models to predict productivity and tool consumption for partial face machines are not as well advanced. There is a need to develop reliable models for partial face machines such as Roadheaders, the Robbins Mobile Miner and the HDRK-Wirth CMM, as these types of machine are likely to predominate in a mining environment. The paper outlines the current state-of-the-art for predicting cutting machine performance and the work being carried out within the Centre for Mining Technology and Equipment (CMTE), in collaboration with the Australian mining industry, to advance our capability in this area.

Jan 1, 1995

By Woodcock J. T, Sparrow G. J

Activated carbon particles obtained from a number of Australian CIP operations were examined with an optical and a scanning electron micro- scope and an electron microprobe. External surfaces, and polished sec- tions through individual particles, were examined with special reference to materials on the surface and to calcium and gold distributions. Photographs are presented of surface contamination of the particles by salts precipitated from the pulp such as calcium carbonate (calcite), calcium sulphate (gypsum), and a magnesium salt; ore minerals such as quartz, hematite, pyrite, arsenopyrite, pentlandite, and various alumino- silicates; and other substances such as grinding media and a fungus. Calcite was very abundant but the other materials were less common. Contamination in the interior of carbon particles was almost exclu- sively calcium carbonate, and extensive contamination extended to the centre of some particles. A possible mechanism for the formation of cal- cium carbonate inside the carbon particles is noted. Gold X-ray dot maps of sections through carbon particles indicated that gold was distributed throughout coconut shell carbons and that although gold was more concentrated near the outer surfaces of extruded peat carbon particles, it was also present to depths of at least 500 ¦m. The gold distribution throughout the carbon particles was similar to that rf alrit~

Jan 1, 1988

By Jones A

Today there is a vast amount of information available relative to the performance of tunnel boring machines, and associated systems. The data referred to here consists of project reports, manufacturer's equipment literature and papers concerning almost every aspect of the excavation process. Why is it then, that many projects that employ full face tunnel boring machines (TBMs), on average perform significantly less than the peak performances reported in this industry?

Jan 1, 1993

The paper poses certain questions relating to mine design aspects of deep shaft pillars. It then explores these questions in relation to Western Deep Levels (South) where a sub-shaft system is to be sunk to 4 000 metres below surface to exploit two narrow tabular reefs in the down dip extension of the mine workings. After brief discussion of some broad considerations, the findings of a major rock mechanics investigation are reviewed. Some overall conclusions as well as the outcomes of separate studies of the anticipated behaviour of shaft pillars on each of the two reef horizons are outlined. The effect of this behaviour on the barrels of the shafts in the system and on the associated shaft excavations and in-pillar development is Cnnctdarcrl

Jan 1, 1986

By Russell P

Polyurethane resin (PUR) is extensively used in almost all coal producing countries. On the local scene, PUR components suitable for underground application were selected and subsequently, trials were carried out at several coal mines. This paper describes the work at Pikes Gully Colliery (B.P.3Coal), where water flow rates of up to 4.5 m (1000 gallons) per minute, were reduced to 1-1.5 m /minute at the tirst stage of application. Subsequent trials were carried out at West Cliff Colliery (Kembla Coal and Coke). A variety of PUR chemical mixtures were tested in coal ribs and in the roof of intersections and roadways. The trial results are presented with all particular details. Using the PUR injection method, the roof, at the most difficult intersection, was stabilised and 'de-bonded' roof bolts were re-sealed. At Pikes Gully and West Cliff Collieries, 2 tonnes and 3 tonnes of PUR chemicals were injected, respectively. The technique, primarily based on German experience (Bergwerksverband), was used by Delta Control Systems Pty. Ltd. ACIRL was closely associated with the trials, which were monitored by installation of the measuring Stations.

Jan 1, 1986

By Isaac AK

The combination of shot-firing and stage loader, and a prop and bar support system is an accepted drivage method. The support configuration is based on the final prop density, and assumes relitively uniform load sharing between the props. During the development of a longwall faceline at a medium depth (approximately 600m) British coal mine using such a drivage method, a fall occured overnight, effectively closing approximately 40m of the drivage. The severity and speed of the fall prompted an investigation into the performance of the temporary support system installed prior to chock installation. This paper deals with the investigation which disclosed some major contributory factors towards loss of strata control.

Jan 1, 1986

By Lama R. D

The Australian underground coal mining industry is undergoing major changes. This paper analyses the technologies presently being researched in mines, and discusses their utilisation as major contributors in the underground mining of coal in Australia over the next 20 years. It describes the problems that underground mining of the year 2000 will face and the possible solutions to those problems based upon results of present day research. Methods, equipment and organisational requirements are outlined. Developments in micro-electronics, computerisation and monitoring will require a new look into human resource development, education and training, and organisation to meet the challenges of the 21st century. The mining system's philosophies of the future are Outlined.

Jan 1, 1986