Search Documents

Kensington is a joint venture between Echo Bay Mines and Coeur Alaska, a subsidiary of Coeur d'Alene Mines Corp. The venture is of equalparticipa- tion and is governed by a management committee with Echo Bay as the operator. The project site is 50 miles north of Juneau, Alaska on the eastern shore of the Lynn Canal. The mine and mill are being planned for a production rate of 4,000 stpd. Currently, probable reserves stand at just over 11.3 million tons grading 0.149 oz Au/ton. The project is now in final feasibility study with a production decision anticipated by the end of 1990. Commercial production would begin early in 1993. This presentation dis- cusses the anticipated mine, mill and support aspects of the project.

Jan 1, 1991

By Kurzeme M, Willoughby D. R

Current research at the CSIRO, Division of Applied Geomechanics, into the mode of response of fill as a structural component has been based on model tests for prediction of behaviour and field observation of critical parameters. The procedure is summarised in four stages: (a) define the specific fill function (b) postulate the mode of failure (c) use models to quantify the conditions (d) monitor critical parameters to check or update the analysis in (c). The above procedure is used to postulate the failure modes of each of the possible func- tions performed by fill materials. Analytical techniques, or lines of investigation, are described for each of these modes and specific reference is made, where, possible, to an exis- ting mine environment.

Jan 1, 1973

By Snowden D. V, Standing C. A, Ryba A, Bywater A

McKinnons open pit gold mine, located within the Cobar Basin in New South Wales, is characterised by complex mineralisation controlled by the intersection of steep faults in the hinge zone of an anticline. Resource estimation using indicator variography and indicator kriging was based on RC drilling on 25 in sections together with grade control RC drilling on 12 in by 12 in and 6 m by 6 in patterns. Rigorous sampling and checking procedures were used to verify the reliability of the drill hole data. Blast hole data was used to assist grade control in defining ore block boundaries.

Jan 1, 1997

BHP World Minerals (BHP) commenced development of the Cannington exploration decline in 1993 using Peabody Resources LimitedÆs Mining Services Division (PRL) as the contractor. Approval was given in 1996 to complete the mine development and bring the mine into production in 1997. The total mine development at Cannington by PRL has included 14 km of headings, 1040 m of shaft sinking for ventilation and ore hoisting and 990 m of raise boring for ore passes and vent rises. Hard money schedule of rates contracts were used for mine development from 1993 until early-1997. This took the mine development down to 570 m below the surface and developed six levels. Because of significant risks, the final phase of the mine development was completed in 1997 under a partnering agreement. This paper examines the factors considered in making the change to partnering, the issues involved in negotiating the partnering agreement to complete the Cannington mine development and the outcomes of the agreement.

Jan 1, 1998

By Vynne J. F

Drill monitors for blasthole and exploration drills have been available to the mining industry since the 1970s. The early monitors were pen strip chart recorders which were developed for the oil drilling industry and adapted to mining. They recorded drilling parameters such as depth, pull-down pressure, torque, RPM, and bailing air pressure. While these recorders could generate a large volume of paper, the amount of useful data was minimal. The data was not summarised and required an engineer to interrupt the chart traces. Being a mechanical recorder, the devices were also susceptible to frequent failures.

Jan 1, 1993

By Turnbull AG

The direct smelting of zinc sulfide con- centrates has been investigated by an extensive series of computer-based thermodynamic equili- brium calculations. The study covers both pure 7.n-S-O-C-N systems and practical concentrate- coal-air-flux systems. It is shown that for a zinc concentrate containing iron and lead sul- tide impurities, a 97% yield of zinc vapour with autogenous operation can be obtained under carefully optimized conditions. The possible integration of this process with existing zinc condensation and recovery processes is Discussed.

Jan 1, 1980

LOCATIONThe property of the Mount Isa Mines Ltd. is situated in Western Queensland, 603 miles by rail west of Townsville, the nearest seaport. All supplies and the bullion are railed between Mt. Isa and Townsville. The climate is semiarid, and operations are conducted throughout the year without difficulty.WATER SUPPLYThe mill make-up water is obtained from the mine, and also from Rifle Creek reservoir, which is situated 20 miles from Mount Isa. The domestic supply of water is obtained from a series of bores on the company's leases.POWER SUPPLYElectric power at 3300 volts, 3-phase, 50 cycles, is supplied from the company's steam power plant, consisting of two units, each unit comprising one Babcock & Wilcox boiler, supplying steam at 300 lb. pressure per sq: in. to one 5000 kW. turbo-alternator. Pulverized coal is used as fuel, and power is being generated at a cost of 0.45d. per kilowatt hour. The coal used is supplied from the State Coal Mine, Bowen, costing 42/- per ton delivered at Mt. Isa.

Jan 1, 1933

By Witkowski A

I have the pleasure to present 6 excellent papers in this section all of major relevance to the mining environment of today where competing social, legal and monetary interests and their often complex interaction require serious consideration. This is particularly true today where huge fluctuations in commodity prices makes mining a perilous undertaking while the world increasingly are becoming aware of the serious threat that mans activities has on his environment. The 6 papers deal with such complex issues as safety in an underground environment; How to protect sensitive wetlands well into the next century; The enormeous waterproblems in China and conflicting dewatering/water supply needs; Disposal of contaminated water in sensitive areas and the dynamic interaction between mining companies and legislation.

Jan 1, 1988

By Lye GN

Rock mechanics investigations have shown that some major slopes in the Panguna pit would be stable at angles in excess of 500 providing near-surface instability could be controlled. Excavation of final batters at angles between 55¦ and 60¦ is now being carried out using D10 dozers with berms at 45 to 60 m centres. A trial slope with berms at 90 m centres is planned. Shotcreting of weak zones combined with crest reinforcement, with rock anchors and dowels, is used to provide protection against erosion and toppling of the crests. Overall slopes excavated in this way are of the order of 10¦ steeper than slopes obtained by blast and shovel excavation.

Jan 1, 1986

Synthetic and commercial activated carbons are characterised for several chemical and physical properties. A range of techniques is used to establish correlations between physicochemical parameters and gold- adsorption activities. The most important parameter in the carbon activation process for a product with a high gold-adsorption activity is the activation temperature. High activation temperatures yield products with large micropore volumes which provides sites that are ideal in size for adsorption. The surface area of an activated carbon is not necessarily a good measure of its adsorption activity. Surface oxygen-containing functional groups are identified by Fourier transform infrared spectrophotometry to be comprised mainly of ethers and hydroxyls. These functional groups line the edges of the micropores imparting a polar character to the pore and aid in the solvation of the adsorbate. Oxidants such as nitric acid result in a proliferation of surface carboxyl groups. resulting in a negatively- charged surface that is not conducive to the adsorption of gold.

Jan 1, 1993

A field trial of the prompt neutron-gamma SIROLOG technique was undertaken by the CSIRO - Division of Geomechanics at Callide Coalfields during July 1989. The trial investigated whether the sonde could reliably be used for the determination of Ash and Iron Oxide (Fe2O3) in coal seams, which had a highly variable iron content. Ten boreholes were logged, being water filled of a nominal diameter of 120 mm. The logging probe employed a 1.6 ¦g 252Cf neutron source and a 51 x 51 mm BGO detector. The source to detector distance was 15 cm. The results from one exploration borehole at the Dunn Creek Mine are discussed in the paper. The rms deviations for ash and iron determination between the neutron-capture predictions of the geophysical logs and the laboratory - chemical assays were 1.9 per cent Ash and 0.88 per cent Fe respectively. Using existing empirical equations which relate iron oxide concentration in coal ash to Initial Deformation Temperature (reducing conditions) at Callide, it may be possible to indirectly determine ash fusion properties as least as accurately, on a more detailed ply-by-ply basis, and more cost competitively than current laboratory techniques allow.

Jan 1, 1991

Open pit mines in the Yilgam Craton have unique hydrogeological characteristics resulting from a combination of geology, mineralisation and the complex and extended development of the regolith. The principal features of this geological relationship are:ò deep and complex multi-stage development of the weathering profile; ò steeply dipping rock layering;ò supergene enrichment; andò mining across the regolith/rock interface.These features result in large changes in permeability horizontally across rock layers; vertically through the weathering profile and along-strike in association with mineralisation and the mineralised Structure.

Jan 1, 1993

By Segnit ER, Boow J

The start up operations of Western Mining Corporation's Kalgoorlie nickel smelter encountered troubles due to the high magnesia content of the concentrates. The flash smelter slags, with higher than normal magnesia content, had a much higher melting point than the normal low-magnesia, predominantly fayalite slags usually produced in nickel smelting. Investigations were made of the structures, melting points and viscosities of the Kalgoorlie smelter slags, as produced, and with additions of silica or lime.

Jan 1, 1980

Basic Oxygen Steelmaking (B.O.S.) commenced in Australia in December, 1962. Two 200-ton furnaces were installed initially at Newcastle with a 50-ton furnace coupled to a continuous casting machine added in 1967. In 1965, two 100-ton furnaces were installed at Whyalla plant and two 225-ton furnaces are nearing com- pletion at Port Kembla to commence oper- ations in 1972. Plant layouts in each centre differ due to changing circumstance and increasing knowledge of the B.O.S. process since 1962. Raw materials are a most important factor for good operation of the process. Most materials come from within Australia but some are imported. General operating practices are similar in each plant, although treatment of fume at Port Kembla will be by the OG (Oxygen Converter Gas Recovery) Process as against electrostatic precipitators in Newcastle and Whyalla. Special alloy steels as well as plain carbon steels can be made by the B.O.S. process. Production potential of the process in Australia has yet to be fully utilised with 45 per cent of steel production coming from B.O.S. In 1971.

Jan 1, 1972

By L O. ÆNeill, J Bebek

When Kalgoorlie Consolidated Gold Mines (KCGM) purchased its fleet of 18 CaterpillarÆs dump trucks in 1999, as part of its change to owner operated mining, five CaterpillarÆs Computer Aided Earthmoving Systems (CAES) were also commissioned on Komatsu PC8000 hydraulic shovels and Caterpillar D10R bulldozers. Since then the CAES system has been installed and operational on Komatsu PC3000 hydraulic shovel, CaterpillarÆs D10R dozers and Cat 994 front-end loader while Cat 854 wheel dozer has been fitted with CAESbasic. This investment in advanced machine guidance and control technology has proven very beneficial over the years for the Super Pit with improved safety and increased operating efficiency and productivity. The paper brings into focus how the CAES system adaptation in unique mining conditions assists in production gain, equipment operatorÆs safety, flexibility and independence, personnel removal from hazardous areas, acquisition of operational information and improvements in mine planning and design, benefiting the entire mining operation.

Jan 1, 2003

By Carlini G, Ibba R

The KSS Lead Plant (Kivcet - SNAMPROGETTI - SAMIM) of Por tovesme, owned by Nuova Samim (the sector-head Company for non ferrous metals and derivatives owned by ENI), has been operating since february 1987. This plant is based on the Soviet Kivcet licence and testwork carried out on the pilot plant of VNIITSVETMET in Ust Kameno gorsk fed by the Nuova Samim's concentrates. The plant is com pletely automatized using the most advanced technologies and it is operated by nineteen people on shift work, including all ancillary units and lead decopperizing-casting. The expected performance of the plant has been confirmed and improves day by day in relation of the operating experience, thanks to the new conceptual design of the furnace. Due to the remarkable flexi bility of the process, the integration of the lead plant with the other plants of the metallurgical complex of Portovesme rro-#4 (Electrolytic Zinc Plant, Sulphuric Acid Plant, Imperial Smel ting) has shown all the economic advantages. The lead content in the ambient air, detected by the monitors, either in the working area and on the ground outside the complex, is widely Pb W" below the stricter new limits recommanded by the E.E.C. (Economic European Community) rules and by the Italian law. The whole process is carried out in equipment completely closed and under suction and it does not require manual operations with exposure to the lead. The production cost is much lower than that performed by the traditional technology. This advantage permits wide margin to consider investment to replace the traditional technology.

Jan 1, 1989

At the Highway gold deposit, 37 kilometres south of Charters Towers, gold mineralisation occurs in several stratiform layers and is enriched near the surface by lateritic weathering. The host rocks of the mineralisation are ferruginous and baritic, intensely sericitised, kaolinised and silicified rhyolitic tuffs and pyroclastics of the Cambrian-Ordovician Mount Windsor Volcanics. The geology of the deposit is illustrated in Figures 1 and 2.Forty-six reverse circulation percussion drill holes were completed by North-Queensland Resources N.L. for a total of 2,093 metres of drilling to further outline and test the open pit resource. The drilling indicated a resource of 171,000 tonnes averaging 4.4 grams per tonne gold and 5.0 grams per tonne silver.A shallow initial pit, approximately 30 metres deep, has been designed to mine the high grade upper portion of the western stratiform layer and part of the eastern layer. This initial pit is designed to mine 45,400 tonnes of western mineralisation at an average grade of 7.84 grams per tonne gold and 22,200 tonnes of eastern mineralisation at an average grade of 1.42 grams per tonne gold. Waste is estimated at 110,900 tonnes.

Jan 1, 1986

By P Dare-Bryan

Many mines have an interest in improving fragmentation at their sublevel caving operations in order to produce better ore recovery, lower dilution and less overbreak. The primary requirement for the extraction phase is to understand and optimise the flow of the fragmented rock in the rings including interactions with the caved material. Rock fragment formation is critically controlled by the blasting phase and can potentially be improved by optimising the dynamic energy distribution throughout the ring through the crafting of explosive charging, priming position and initiation timing. The modelling of fragmentation and damage due to explosive loading of complete rings is inherently and irrevocably a three dimensional problem that is difficult to address. We have therefore initially utilised an analytical code to predict vector peak particle velocities and energies that are restricted to the plane of a ring. Dynamic energy distributions based on common timing and priming practice have been compared with other possibilities using conventional pyrotechnic detonators as well as initiation designs based on accurate electronic detonators. The energy distribution can be quite subtly tailored to increase energy in appropriate regions or to decrease energy in the brow region for example to potentially reduce instability and the probability of misfires. We have also recently developed the capability to efficiently model particle flow using four-sided polygonal elements. Despite the 2D limitations of such a model this results in more realistic fragment interaction and stacking than can be achieved using conventional rigid circular elements. Modelling of a typical sublevel caving ring utilising these elements activated by the correct dynamics offers considerable potential for understanding the influence of the blasting energetics and timing on the complex flow and extraction process.

Jan 1, 2005

By T Leach, F Kaiqiang

The Jianchaling gold deposit is located about 1200 km south west of Beijing in central China. The deposit was discovered in 1988 by the Northwestern Geological Exploration Bureau (711 Exploration Team). Sino Gold Limited, an Australian based company, developed the mine in 1998 and is currently operating a 1000 t per day underground mine, producing about 80 000 ounces of gold per year. The pre-mine resource for Jianchaling was 1.6 million tonnes at 9.85 g/t gold. The deposit occurs within the east-west trending Mesozoic Qinling-Dabie orogenic belt formed during the Yanshanian Orogeny. In the Jianchaling region, gold mineralisation is primarily hosted by regional west-northwest to east-southeast striking faults, the most important of which, the reverse sinistral F145 fault, hosts the larger gold deposits including Jianchaling. At the mine scale, the most important zone of mineralisation is localised within a shallowly north dipping dilation on the F145 fault. Proterozoic dolomite forms the hangingwall and serpentinite and talc schist the footwall to the fault. Within the footwall, serpentinite is the most important host rock to mineralisation. Initial alteration involves replacement of serpentine to dolomite ¦ pyrite, talc to ankerite ¦ pyrite, and magnetite and chromite to pyrite, the latter locally through a transitional hematite phase. Proximal to feeder structures, the carbonate minerals have undergone partial dissolution and replacement to quartz. Gold is related to arsenean pyrite and marcasite rimming and replacement of early-formed pyrite, and associated with iron release during the processes of dolomitisation, silicification and carbonate dissolution.

Jan 1, 2004

By Beattie T. A

The ability of explosives to fragment rock has been assessed in small scale trials at the Granite Rock quarry, Baimsdale, Victoria. Three 65 mm diameter holes were fired simultaneously in a five metre bench, and the rock collected, screened and weighed. The mass of fines increased as the explosive strength increased in the series 30(10 ANFOPS

Jan 1, 1990