Search Documents

By Ramani R. V

There are many important physical phenomena in mine ventilation which involve transient mass and heat transfer processes. These processes have been modeled using differential equations often solved with close form solution. Within the last two decades, many numerical schemes have been devised to solve these mass-transfer problems. Much of this effort has focused on variants of the finite element and finite difference methods. In this paper, the solution of mass transfer models in mine ventilation by finite difference technique is discussed. Specifically, the computational effort and the accuracy of the solution are presented.

Jan 1, 1988

By Misra A

After review of the status of research on optirnisation of retreat longwall faces it is argued that an acceptable optimisation model must be based upon realistic cost data that take into account not only the face costs, but the total panel costs. These include the cost of development, face cost, removal and installation cost. The determined optimum length of a retreat longwall face is based upon a realistic model and actual costs.Parameters that influence the optimum face length have been varied over wide limits to allow determination of the sensitivity of the model and the effect of the parameters on the optimum face length. It is concluded that for medium production rates and medium system availability, the optimum face length of a retreat longwall face under Australian conditions lies between 180 and 220 metres.

Jan 1, 1995

There are a number of mineral processing operations which produce at some point a stream of hot particulates. At today's energy prices it becomes important to recover the energy held in the hot particulates. Sometimes it is convenient to use gas, e.g. in air pre- heating, and this will be appropriate in some circumstances. There are cases where it would be very useful if energy in the hot processed particles could be exchanged to the cold feed solids. This can be achieved within appropriate limitations by countercurrent heat exchangers comprised of parallel channels which contain, alternately, fluidized solids of 'hot' and 'cold' streams respectively. A pilot- plant has been built. Some calculations relating to industrial application will be Presented.

Jan 1, 1981

Polish coal mines are well equipped with methane monitoring systems,nevertheless the worsening conditions force a continuous impro- vement in the field of environmental monitoring. Application of modern electronic components make it possible to design the new modular telemonitoring system incorporating the best features of the older systems,widely employed in Polish collieries, eliminating their weak points. Several new sensors and portable instru- ments for methane monitoring and early fire detection have been developed and tested in mining conditions.

Jan 1, 1988

By S Q. Zhao, J H. Wei

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Xitieshan lead-zinc deposit is located in the north margin of the Qaidam Basin, Qinghai Province, China. It is one of the largest massive sulfide deposits in China and is supposed to be of the sedimentation-exhalation (SEDEX) type. Based on the main ore mineral and sulfur isotopic compositions in sulfides found in the wall rock, the S of the deposit is considered to originate from the mantle, but the fluid potentially mixed with sea water during the hydrothermal circulation exchange. The study of lead isotopes shows that the metallogenic material is characterised by the mixture of orogenic and upper crust sources. The lead isotopic signature of the wall rock is similar to that of the ore, which shows synsedimentary characteristics. According to the composition of the rubidium and strontium isotopic signature, the value of 87Sr/86Sr is lower than the average value of that in the crustal rock, which is larger than that of the mantle. Hence, the metallogenic materials of this deposit mainly originate from the crust, which is related to materials of volcanic rocks activation and migration of the deep hot circulating water. The process of the metallogenic fluid circulation shows continuous interaction with crustal material and lead to continuous enrichment of the ore forming fluids. From the study of the fluid inclusion microthermometry of the ore and the associated minerals combined with the C, H-O, Si isotopes, it is believed that the metallogenic fluid is mainly coming from the mantle or the deep magma chambers. The rising deep fluid then mixes with the sea water. The carbon dioxide escaping and mixing with sea water during the hydrothermal exhalation process leads to the rapid precipitation of the hydrothermal fluid to deposit metal. That is proposed as the principal formation mechanism of the Xitieshan deposit. Further studies are proposed, including obtaining geochronology data from this deposit.CITATION:Zhao, Z X, Wei, J H, Liang, S N and Zhao, S Q, 2015. Advances in research on metallogenic mechanisms for the Xitieshan sedimentation-exhalation lead-zinc deposit, Qinghai Province, China, in Proceedings PACRIM 2015 Congress, pp 487–494 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Autogenous and Semi-Autogenous grinding has become an accepted method of reducing primary crusher product to micron sizes in a single or a two-stage grinding circuit. The elimination of secondary and tertiary crusher circuits and sometimes rod mills helps to lower overall operating costs and, in many instances, can make uneconomical projects viable. Selecting AG/SAG Mills have been rather a "hit and miss" affair over the years, but now with the many different types of tests available, accurate mill size predictions can be made, provided the test data is evaluated correctly. This paper endeavours to simplify the process of evaluating test data and sets down some guidelines for designers to follow when selecting AG/SAG Mills.

Jan 1, 1991

The sinking of the new No. 3 Shaft being mainly concerned with providing for the continuation of mining operations north of the existing workings, requirements for the shaft and haulage equipment were assessed, having in mind the anticipated needs of the Company in future years, the .available knowledge and probable future trends of the orebody, and also that the shaft would be required to act as a downcast airway for the ventilation system associated with the northern underground workings.

Jan 1, 1957

By D J. Williams, A K. Kho, A Shokouhi, N Tucker

The disposal of dewatered coalmine tailings and coarse reject within spoil piles is gaining popularity as a means of eliminating separate surface tailings storage facilities or dams. The contrasting characteristics of coalmine spoil, coarse reject and tailings are somewhat complimentary, making the co-disposal of dewatered tailings within spoil piles geotechnically feasible and environmentally attractive. However, the impacts of mixing plant rejects within spoil piles are not well understood; in particular, the effects of water draining from the mixed plant rejects on the moisture content of the surrounding spoil. Changes in moisture content can cause additional collapse and degradation settlements of the spoil pile. A series of laboratory tests has been undertaken on mixtures of dewatered coalmine tailings, coarse reject and spoil. The results of these tests have been incorporated into a spreadsheet-based settlement prediction tool to investigate the effects of incorporating mixed plant rejects on total spoil pile settlements. This paper presents the laboratory tests undertaken, the incorporation of the test data into the settlement prediction tool, and settlement estimates for the various mixtures at different stages of construction.CITATION:Kho, A K, Tucker, N, Williams, D J and Shokouhi, A, 2015. Impact of co-disposing mixed plant rejects on spoil pile settlements, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Christie GB, Mainwaring DE, Leong YK

High solids brown coal slurries have been prepared with concentrations approaching those achieved with bituminous black coals. The high inherent water content and macroporosity of Victorian brown coals have been reduced in a controlled manner by chemical and mechanical means. The hydrophobicity of the coal surface has been increased sufficiently to reduce the tendency for swelling and water uptake. This together with densification has allowed the solids content to be progressively improved from 25% solids with raw coal to 65% solids with modified coals. Both raw brown coal and modified brown coal suspensions show shear thinning behaviour resulting in lower viscosities at higher flow rates. All coal suspensions displayed a yield stress once sufficient solids concentration was achieved. This yield stress can be used in the prevention of solids settling. Under simple shear mixing the network structure that provides the yield stress quickly breaks down to a low viscosity fluid with reduced yield stress and a pumpable consistency. The time necessary for structural recovery is in the order of days permitting shut-down and start-up of fuel delivery systems.

Jan 1, 1987

By Pollard DM, Willis GM

The removal of bismuth from liquid copper in a vacuum furnace was studied over a range of pressures. The rate determining step changes from diffusion in the gas at pressures above 0.2 Torr to approach the Langmuir evaporation rate at pressures of 10-2 Torr. Oxygen and sulphur were found to have a negligible effect on the rate. Bismuth removal from copper sulphide was found to be considerably slower than from copper. This is consistent with the known thermodynamic properties of ternary sulphide melts.

Jan 1, 1980

In the past few years the Rietveld method emerged as a routine tool for quantitative phase analysis (QPA) from X-ray diffraction data. Fast and reliable results became possible by combining modern computer technology and optimised mathematical algorithms with the fundamental parameters approach in the Bruker AXS TOPAS software. Here the routine analysis of bauxite raw material and of aluminium bath electrolyte is presented. The accuracy of bauxite quantification was tested by analysing the IUCr round robin sample. An agreement of better than one per cent was obtained for minor constituents and a maximum deviation of 2.5 per cent for the major phases. This is excellent agreement with expected results from weighting. Ten different phases were quantified in natural samples from Turkey with a precision better 0.5 per cent for the major phases and one per cent for the minor phases. Additionally, crystallite sizes were obtained from the peak profiles that give valuable information for the processability of the material. XRD data from solidified aluminium electrolytes were rapidly measured using silicon strip detector technology. With the LynxEyeTM detector full patterns were collected in 90 seconds and analysed with TOPAS. It is shown how to derive well-established measures such as bath ratio and excess AlF3 from the Rietveld results. These measures are widely used in aluminium production and readily available with very high precision. The excellent agreement with ALCAN reference data demonstrates the outstanding accuracy of the method. The mean deviation between here presented results and reference data is below 0.5 per cent for total CaF2, below 0.25 per cent for excess AlF3 and 0.02 for the bath ratio. The precision of the method was evaluated by repeated measurements.

Jan 1, 2008

By Short KC

The Hunter Region, with a major part of the coal resources of New South Wales and a long history of coal mining, has experienced a rapid expansion of coal resource development in recent years. While there are inevitable conflicts between mining, urban development and related infrastructure, and between mining and other resources, the application of sound planning practices, and improved co-operation and co-ordination among the various parties, helps to reduce such conflicts. The planning process involves consideration of factors such as transport- ation (including port facilities), mine subsidence, provision for surface facilities, a,iC the need for buffer 'ones. In addition, provision must be made for urban expansion, often co-existing or in close proximity to present or future coal mining development. Approval of coal mining developments takes place within the legislative framework of the Environmental Planning and Assessment Act, 1979 (EPA Act), the Coal Mining Act, 1973 (CM Act) and the Mining Act, 1973. Considerable effort has gone into stream- lining and co-ordinating the procedures under these Acts. The EPA Act provides for regional and local environmental plans, as well as a linked process of development control and environmental impact assessment. The CM Act provides for the grant of exploration and coal mining titles and mechanisms for the responsible management of Mining.

Jan 1, 1987

Firedamp drainage has become an essential part of many mine environmental systems, and new applications are arising. Installations are evolving further to satisfy ever changing basic requirements, standards, and iniilny needs. In this paper, water seal, vacuum based installations are considered, as well as moni- toring, protective and control systems which have been developed for continuous, manless, and trouble free operation. Some factors affecting plant capacity and extractor per- formance are identified and assessed. INTRODUCTION Firedamp drainage applications are incr- easing world wide as mining engineers strive for improved safety and security, and further concentration of coal output. Fewer and fewer mines are able nowadays to satisfy coal prod- uction and firedamp control requirements solely by air dilution or by air dilution and underground firedamp extraction plants. As a result, dependence on surface extraction plants is increasing. This paper deals with som requirements and applications of such installations. I. DEVELOPMENT AND PRACTICE Firedamp drainage has existed for over 250 years following the early work of Carlisle Spedding at Whitehaven (1730). Some fundamentals of current firedamp drainage systems can be recognised in the

Jan 1, 1982

By M McCarthy

Attraction, recruitment and retention of quality mining engineers is becoming increasingly difficult for many mining companies. Part of the problem is attracting young professionals, especially given the decline in graduating engineer numbers, and the other is balancing the new engineerÆs development with business needs. The evolution of the graduate program at Olympic Dam over the last five years has resulted in substantial benefits for both the engineer and the company. The program has developed to provide structured exposure to key areas of the mine enabling new engineers to step into vacated roles as the need arises. The pool of quality engineers generated by the graduate program is a buffer against high industry turnover and helps reduce future recruitment expenditure. Olympic DamÆs program goes beyond conventional recruitment of graduate engineers. Innovations designed to improve intake include the employment of graduate engineers as well as final year students, retraining of existing personnel from other backgrounds and fast track recruitment for previous vacation students. By employing a cross-section of professionals to complement the generic university graduate, the company takes full advantage of the relevant lifestyle experience belonging to the individual, which is a substantial factor in turnover. Study assistance and a salary paid for final year students and mature age students often creates a loyalty that lasts beyond graduation. Careful selection of vacation students increases the ease of recruitment at a later stage and ensures that full advantage is taken of the relationship developed previously between the company and young professional. The evolution of recruitment at Olympic Dam has seen a decline in the turnover statistics of young mining professionals.

Jan 1, 2005

By I Lumsdaine

QNI Pty Ltd operates the Yabulu Refinery located 25 kilometres north of Townsville, North Queensland. The plant treats nickel laterite ores sourced from the Philippines, Indonesia and New Caledonia. The cobalt head grade and overall recovery expectations for the 2001/2002 financial year are 0.161 per cent and 53.8 per cent respectively. Cobalt is a valuable byproduct derived from the nickel refining operation which utilises the Caron Process. Any increases in cobalt recovery that are achieved from the existing relatively low level provide significant improvements to the bottom line of the operation. Towards the end of 2000, a project was undertaken to characterise cobalt losses with the sole purpose of improving cobalt recoveries using a variety of analysis techniques. The Time-of- Flight Secondary Ion Mass Spectrometry (TOF-SIMS û University of South Australia) method was used to verify the presence of surface bearing cobalt species, originating from either co-precipitation or adsorption mechanisms. Cross-section examinations were also performed using Scanning Electron Micrscopy (SEM) and Energy Dispersive X-ray Spectrometry (EDXS). These techniques indicated the presence of high cobalt concentrations (in the order of several per cent) within a select number of roasted and leached ore particles. The phenomenon of cobalt losses due to incomplete leaching within specific ore particles was not widely documented within the Refinery prior to these studies. In order to quantify losses via this mechanism, Mineral Liberation Analysis (MLA û JKTech Centre) was also performed on key samples. This paper serves to document a systematic approach in determining the source of significant valuable mineral losses in an established, operating plant. It discusses the use of a variety of analytical techniques, which have been adapted for the minerals processing industry, but are strongly relevant for plant investigations in the hydrometallurgical industry.

Jan 1, 2002

By A Halim

The European Union (EU) have recently issued new Threshold Limit Value-Time Weighted Average (TLV-TWA) for diesel exhaust contaminants, which are CO, NO2 and DPM. The new limits for CO and NO2 were issued in 2017 whilst the one for DPM was issued in 2019. However, in order to allow EU mines to formulate strategies to comply with these new limits, the EU granted a transition period in which mines could use the old limits until the new limits are enforced. The new limit for CO and NO2 will be enforced from 21 August 2023 whilst the one for DPM will be enforced from 21 February 2026. The new limit for NO2 and DPM is very low, 0.5 ppm for NO2 and 0.05 mg/m3 of Elemental Carbon (EC) for DPM. Combination of these two limits would be the lowest among all mining jurisdictions worldwide. It poses a huge compliance challenge to EU mines if they keep using diesel machines. Therefore, a study and a field trial were carried out by the author in 2019–2021 to investigate whether replacing diesel machines with Battery Electric Vehicles (BEVs) would be the best answer to this challenge. This paper outlines results of this study and field trial.

Oct 12, 2022

By Hinde J. S

The Fitzpatrick Orebody is a three and a half million tonne fault bounded portion of the early-middle Proterozoic Broken Hill Orebody.The Fitzpatrick Orebody was discovered in 1975 by diamond drilling from the 36 Level Exploratory Drive. This followed persistent geologically oriented exploration and a courageous decision by mine management to deepen No. 3 Shaft to provide exploratory development across the Globe Vauxhall Shear and allow effective drilling of the target area.The stratiforrn oebody consists of three lenses, the lead rich No. 2 and 3 Lenses and smaller zinc lode. They represent a down plunge extension and boudinaged, fault-bounded portion of the main Broken Hill ore lenses. The surrounding host rocks are extensively faulted and jointed due to complex history of movement on the bounding shears. This results in extremely poor ground conditions during mining. The ore was delineated for mining development using three dimensional fan drilling from exploratory and hanging wall drive drill sites.

Jan 1, 1990

In recent years a number of explosive blends including ANFO, emulsion and watergel products have been used in a variety of ground types and applications. These `standard' explosives' technologies are not new, but out of the uses and applications, have sprung a new generation of tailored explosives that match the ground type and the operating environment. This is in stark contrast to the norm, where various patterns and loading configurations have traditionally been designed to accommodate the explosive. This paper discusses these tailored explosives and the explosives' technology behind why they work. Active tailoring of explosive formulations can save mining dollars while essentially leaving the explosive price unchanged. Tailoring explosives may lead to increased rock breakage, heave, digging rates; lower digging maintenance costs and in some cases replacing earth moving machinery altogether. Tailored explosives may have other benefits such as reduced over pressure compared with standard alternatives. The tailoring of explosive performance generally involves three major methods (other than changing the bulk density and sensitivity): (i) replacing fast burning reactants with slower burning reactants or vice versa; or (ii) leaving the explosive intact and diluting the entire explosive with slow burning or `inert' material; or (iii) changing the concentration of the fuel/oxidiser mix. When tailoring explosives for particular applications, authorising, testing, costing, manufacturing, and delivery systems must also be taken into account.

Jan 1, 1995

By J Zhou, L Crompton, K P. Galvin, J L. Sutherland, C P. Lowes, C Bezuidenhout, J Bijzet

Platinum Group Metal (PGM) bearing ores from the Upper Group 2 (UG2) reef often contain significant concentrations of chromite which can potentially be upgraded to produce a saleable product. A common approach is to implement gravity separation on the PGM flotation circuit tailings. However, where the particle size range of interest is broad and the lower size limit ultra-fine, the challenge is how to maximise the recovery at a saleable product grade without compromising throughput. This study was concerned with the performance of a REFLUX™ Classifier for beneficiation of a PGM bearing chromite ore and the benefits of size classification. The sample had a nominal top size of 0.5 mm and was processed over the complete size range and in two discrete size classes following classification at 106 µm. The primary goal was to produce a concentrate exceeding 40 wt. per cent Cr2O3, ideally approaching 42 wt. per cent Cr2O3, with minimal PGM losses above 106 µm. A major challenge was to process at the required solids throughput in a single stage with the feed pulp density constrained to a nominal upper limit of 30 wt. per cent solids. It was found that varying the controller density set point of the REFLUX™ Classifier produced strong control of the product grade. Products as high as 41.1 wt. per cent Cr2O3 were produced at 78.6 per cent recovery for the +106 µm material, while in the −106 µm portion the product grade was as high as 41.4 wt. per cent Cr2O3 at 83.2 per cent recovery. Processing the feed in discrete size classes enabled the volumetric feed and fluidisation rates to be optimised for a given application; hence, superior performance was achieved at the finer sizes. This work has demonstrated the value in considering feed preparation as well as technology selection in developing a robust process solution.

Aug 24, 2022

By Black PM, Itaya T

Arc-type volcanic activity has been a major feature of the late Cenozoic geological evolution of the Pacific-Australian plate boundary in the northern New Zealand region. The timelspace distribution patterns of arc-type rocks reflect changes in the nature of the plate boundary as it has evolved. Inception of volcanism began in the north during earliest Miocene times (26 Ma) following ophiolite emplacement and during the next 10 Ma developed into a volcanic arc segment extending south to the present position of the central North Island. The northern part of the arc became extinct about 15 Ma ago, but activity continued in the central (Coromandel) part of the arc until about 5 Ma ago. In late Pliocene and Quaternary times volcanic activity has become concentrated in a northeast trending zone which is collinear with the Tonga-Kermadec Arc.

Jan 1, 1995