Search Documents

By C Sylvestre

Leaders have invested heavily in traditional safety management to improve safety performance over the years. This primarily involved: • fixing the environment (eliminating the hazard) • improving the system (more/less rules, procedures etc) • making safety more conscious (more/better interactions about the importance of safety). These approaches have helped improve safety performance significantly during the last 50 years and will continue to play a role in the future. Although these approaches may be part of an overall solution, they are not enough to prevent many incidents. Today, these three approaches are used more than before, and are used better than ever before. Yet, workplace fatalities in Australia have stagnated from 2013 to 2019, as have the number of incidents, even serious ones. In the USA, workplace fatalities have increased by 15 per cent in the same period.

May 5, 2022

By E T. Baker, J A. Resing, S L. Walker, V Ferrini, F Martinez, R Haymon

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Enumerating active sea floor hydrothermal sites has been a challenge since their discovery almost 40 years ago. High-temperature hydrothermal sites are readily discoverable, primarily by detecting mineral-laden plumes, but working at these sites poses severe environmental and operational difficulties. Low-temperature vent fields, which may represent waning of venting from high-temperature systems, may be more accessible but are more difficult to locate. Over the last decade, however, oxidation-reduction potential (ORP; aka Eh) sensors capable of detecting minute concentrations of reduced hydrothermal chemicals have been successfully used to pinpoint such fields. In this extended abstract, we use ORP anomalies observed during continuous (towed sensor) plume surveys to estimate site frequency along four intermediate- to fast-spreading ridge sections. From these data, we estimate site frequencies between five and 16/100 km for these ridge sections. Previous camera surveys on the fast-spreading East Pacific Rise support these frequencies. These rates are much greater than the frequency of ~0.5–5/100 km, generally increasing with spreading rate, derived from well-surveyed ridge sections in the InterRidge database (InterRidge, 2014). The higher frequencies arise because ORP sensors are able to distinguish between sites as close as ~1 km and identify sites with negligible or no optical plume signal.CITATION:Baker, E T, Resing, J A, Martinez, F, Haymon, R, Walker, S L and Ferrini, V, 2015. How leaky are oceanic ridge axes? A new assessment of the spatial density of submarine hydrothermal discharge, in Proceedings PACRIM 2015 Congress, pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By E Jamieson

For a number of years, Alcoa World Alumina Australia (Alcoa) has been investigating opportunities to produce economically viable products from bauxite residues. Three of these potential products are described here, being Red Sand, ALKALOAM« and REDLIMETM.Red Sand has a nominal particle size of +100 micron and is physically little different to crushed bauxite from which it is derived. In AlcoaÆs Western Australian refineries, Red Sand constitutes up to half of the residue going to impoundment areas. Initial testing indicates that this sand could be processed to provide an acceptable general landfill material, a construction back fill or a material suitable for road base construction. ALKALOAM« is the fine-grained residue often referred to as red mud. A great deal of work has been done to show the benefits of adding this material to sandy soils, which are common in coastal regions of WA. ALKALOAM« has properties that can elevate the pH of the acidic soils and also retain phosphorous, reducing overall fertiliser use and protecting sensitive waterways. REDLIMETM is a by-product of the refining process. This material has a high acid neutralising value. REDLIMETM could be more effective at pH control than most available products because of the fine particle size and sodium carbonate that remains with the product.

Jan 1, 2004

By D E. Thorp

The mining and concentration operations of New Zealand Steel have been carried out initially from the Waikato North Head (WNH) deposit since 1969 and subsequently from the Taharoa deposit since 1972. Over the years the WNH operation has produced about 1.2 million tonnes of concentrate which has been converted into steel, while total exports to the Japanese Steel Industry from Taharoa reached five million tonnes in February of this year. Recent expansion plans both in domestic steel production and in the ironsand concentrate export market have made it necessary for the company to look closely at, among other areas, the mineral processing of the titaniferous ironsands in both deposits. This paper deals with the recent test work carried out at WNH and Taharoa on the use of the cone concentrator unit as a primary gravity concentrating unit ahead of the magnetic separation stages and as a cleaner concentrator following the primary magnetic separation.

Jan 1, 1977

The application of methods using large diameter down holes has become an important facet in both the development and stoping operations of mines within the Aberfoyle group. Holes of up to 98 metres (vertical) and 78 metres (inclined) have been successfully used in stoping operations. A number of rises have been developed to meet ventilation, servicing and escape-way requirements. The most ambitious rise to date has been a..vertical 93 metre long by 4.50 metre square ventilation rise. Although some early problems were experienced, the ultimate successful completion of this rise has enabled the technique to be incorporated with confidence in future mining plans. This paper summarises experience in long hole rising techniques, their evolution from the original cratering concepts, and the approach to further development of these techniques.

Jan 1, 1982

By T N. Little

This paper is concerned with the influence of engineering geology on design of Wall Control Blasts. In the Introduction, the Blast Management Framework and the Blast Design Requirements classification system (previously developed by the author) is drawn upon to set the context. Blasting objective for all wall control blasts involves both profile and damage control. Four classes of approaches for blast design are outlined and briefly discussed. Five distinct wall control blasting techniques are summarised. The general relationship between geology and blast design is explored in the paper. Influence of geology on pre-split and post-split design and blasting direction is highlighted. Wall damage modelling from the closest row of blastholes is also introduced using the Analytical Damage Model (ADM). The relationship of rock properties and explosive selection and in particular the Mach wave generation is introduced to assist blast designer in this regard. Finally a Conceptual Model that relates vibration, damage and rock mass condition has been presented along with some applications that have been undertaken by the developer. Eight conclusions have been formulated based on extensive work in this area and the current study.

Jun 22, 2022

By F Minz, P Lamberg, A Mwanga, C Lund, C Wanhainen, M Amiri Parian, J Rosenkranz

A geometallurgical model is currently built in two different ways. The first and the most common way relies on geometallurgical testing, where a large number of samples are analysed for metallurgical response using small-scale laboratory tests, eg Davis tube testing. The second, mineralogical approach focuses on collecting mineralogical information over the orebody and building the metallurgical model based on mineralogy. At Lules University of Technology, Sweden, the latter method has been adopted and taken further in four ongoing PhD studies. The geological model gives modal composition by the help of element-to-mineral conversion and Rietveld X-ray diffraction. Texturally, the orebody is divided into different archetypes, and liberation measurements for each of them are carried out in processing fineness using IncaMineral, a SEM-based technique. The grindability and liberation spectrum of any given geological unit (sample, ore block, domain) are extrapolated from the archetypes. The process model is taken into a liberation level by mass balancing selected metallurgical tests using the particle tracking technique. The approach is general and can be applied to any type of ores. Examples of ongoing studies on iron and massive sulfide ores are given.CITATION:Lamberg, P, Rosenkranz, J, Wanhainen, C, Lund, C, Minz, F, Mwanga, A and Amiri Parian, M, 2013. Building a geometallurgical model in iron ores using a mineralogical approach with liberation data, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 317-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

Gold was discovered at Waihi in 1878. In 1987 the modern Martha Mine opened in the middle of the town of Waihi. Newmont Waihi Gold as the current licence holder has been operating the mine since 2000. The current open pit was scheduled to stop production in mid 2006. An underground mine is currently being developed to the east of the town.   In 2001 serious subsidence issues from historical underground mine workings outside the mining licence and the forecast closure of the open pit acted as a catalyst for the development of new communication initiatives.   In this context Newmont Waihi Gold and the Hauraki District Council initiated a community consultation process with the people of Waihi. The Waihi Community Consultation Committee (WCCC) was established in May 2003. After an initial brief to act as a forum for community participation in closure and rehabilitation of the Martha Mine, the group quickly took on a much more proactive role working towards the long-term social, environmental, cultural, economic and spiritual sustainability of Waihi.   In the course of over three years of meetings all groups represented on the committee have presented their views, developed ideas and established an organisational structure to bring those ideas to fruition. The challenge now is to work together to consolidate likely options, seek sources of funding, produce business proposals and implement the plan for the future of Waihi.   This paper backgrounds the experience to date and describes the outcomes of the process. For more detail on process considerations this paper should be read in conjunction with Part C by process facilitators, T Clark and S Stewart. For more detail on progress towards the groupÆs goals and future possibilities, this paper should be read in conjunction with Part B by Vision Waihi Trust CEO, E Morrow.

Jan 1, 2006

By M T. Grigoleit, M S. Schneider

The iron ore industry in Australia has, in recent years, experienced an unprecedented growth phase. But now that major expansions are moving into the operation phase, new challenges have emerged. Whereas initial planning may involve a few modelling studies, ongoing performance monitoring and improvement requires a different, more intense approach. This is especially important in the face of changing factors such as commodity prices, exchange rates and labour markets. Response time is key. As a mining operation proceeds from initial planning to daily operations, the time window for analysis shortens, going from months to weeks to days as the business matures.Simulation models and analysis tools are typically built and run by specialists in the planning phase, but then what? The investment has been made, but realised only once. What if further analysis could be carried out in-house, re-using existing models using up-to-the-minute data? Can we create virtual mines that run in parallel to live operations that allow computers to identify areas of a value creation or operational improvement? These questions can be answered by the innovative application of big data, simulation and predictive analytics. The future will be having this all integrated into one platform that offers, for the first time, an opportunity for non-experts to apply existing modelling and analysis assets – combined with live data – to deliver support for continuous improvement, and the ability to respond quickly to external changes in the best possible way, before they become big problems. These techniques will represent a step change in the ability for operations to maximise efficiency and will underpin the intelligent operations of the future. These issues are addressed in this paper.CITATION:Schneider, M S and Grigoleit, M T, 2015. Maximising productivity through big data, simulation and predictive analytics, in Proceedings Iron Ore 2015, pp 475–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

MIM Holdings Limited (MIM) committed to a long-term future in copper in the Carpentaria Mineral Province in 1996 with the development of the Enterprise and Ernest Henry mines, and an upgrade of MIMsÆ copper smelter in Mount Isa, and copper refinery in Townsville. The upgrade of the copper smelter will enable the smelter to produce 250 000 tpa of copper with a single primary smelting unit, the copper Isasmelt furnace installed in 1992. The copper Isasmelt furnace currently smelts concentrate containing 145 000 tpa copper. To reduce the risk associated with the copper smelter upgrade, and shorten the ramp up time of the upgraded smelter, two high-rate trials were undertaken in 1997 to demonstrate that the copper Isasmelt furnace could, with an additional 525 tpd of tonnage oxygen, treat concentrates containing 250 000 tpa copper. During the trials the concentrate feed rate to the Isasmelt furnace was increased from its average rate of 100 tph of concentrate to 150 tph of concentrate. The increase in the capacity of the furnace was achieved by: supplementing the installed tonnage oxygen capacity of 595 tpd with an additional 300 tpd supply; reducing variability in the furnace feed rate from ¦25 per cent to less than ¦5 per cent; and reducing tramp air. The Isasmelt furnace smelted concentrate at a rate of 140 to 150 tph for four hours 25 minutes during Trial 1, and at a rate of 150 tph of concentrate for five hours and 30 minutes during Trial 2. The oxygen utilisation was 100 per cent during the trials with the process remaining under control. As a result of the development work for the trials the average treatment rate of the furnace under normal conditions increased by ten per cent.

Jan 1, 1998

By Susanto A

As part of the current NERDDC funded project studying Dragline/Hopper/ Crusher/Conveyor systems for overburden removal, an investigation was carried out to assess the feasibility of automating the swing-to-dump phase of the dragline digging cycle in order to main- tain consistent performance of spotting the bucket above the hopper prior to dumping. The study involved design of automatic position controls for the hoist, drag and swing drives and simulation of detailed mathe- matical models of the three electromechanical systems and their associated electrical control schemes. The design of the hoist and drag systems to position the bucket in the boom plane is relatively straightforward. Simulation results show fast and accurate performance, with no evidence of interaction between the two drive systems through the ropes. The design of the swing position control system involves special strate- gies to cater for variable inertia and to damp the pendulum oscillations of the bucket. The use of a bucket pendulum model and variable dynamic compensation embedded within the feedback control loop, along with optimal speed/angle slowdown trajectories, has yielded fast and damped positioning responses under simulation.

Jan 1, 1989

By Clarke RG

Renison Mine was developed as the first all diesel mine in Australia. The foresight of the early planners in committing the Mine to Decline access has paid dividends in the past two decades with Renison Mine establishing itself as one of the most productive underground mines in the world. The excellent productivity has also resulted from the development of mining equipment technology, both on the part of the equipment suppliers and through the coordination of the Mining, Automotive and Technical Design Sections at Renison Mine. Constant improvements in truck and loader design, the design of specific equipment to carry out specialized tasks such as installation of services, scaling and ground support and the conversion to electrically powered equipment have been ongoing at Renison. Currently, larger scale trucks are being investigated for ore and waste haulage due to increased haulage distances and production requirements. It appears as though an articulated low profile truck of around 50 tonnes capacity may provide the short term solution based on the performance data available.

Jan 1, 1982

The object of this paper is to give an insight into various metallurgical operations involved in the making and shaping of steel for shipbuilding at the Newcastle plants of the Broken Hill Proprietary Co. Ltd., Commonwealth Steel Co. Ltd. and the Port Kembla plant of Australian Iron and Steel Ltd. Whilst not steelmakers, inasmuch as their processes start with semi-finished. steel supplied by the Steelmaker, the plants of Stewarts and Lloyds (Aust.) Pty. Ltd. and their associate company, British Tube Mills, Rylands Bros. (Aust.) Pty. Ltd. and the Newcastle and Kembla plants of John Lysaghts (Aust.) Pty. Ltd. make substantial contributions to the Australian shipbuilding industry, principally by way of boiler tubing and wires for welding rods and sheet steel, including special silicon lamination sheet for electrical motors.THE MAKING OF STEELThe making of iron and steel began as an accident, slowly developed as an art and has not yet become an exact science. The iron age dawned on the day when, by chance, man's primitive ancestor built up the wall of his fire with ironstone. In the ashes of the fire he found pieces of sponge iron from which he hammered out the first sample' of wrought iron. For many centuries iron ·was manufactured in bloomeries and occasionally, when the temperature was excessive, the iron combined with some carbon and steel was produced. But it was not till '1740 that steel was manufactured under controlled conditions. In that year Huntsman invented the crucible process which held undisputed sway for over a 100 years until in 1856 the invention of the Bessemer process revolutionised the whole industry.From then on, rapid progress was made. The Siemens...

Jan 1, 1951

By J J. Grobler

The George Fisher Underground Mine at Mount Isa applies the long hole open stoping methodology. During the reconciliation process of transverse stopes in the George Fisher North mine it was identified that excessive underbreak was regularly experienced, with the major contribution coming from the toe area inside the stope.While over break and the resultant dilution was well investigated and well understood, limited work was done on underbreak improvement. It was decided that a re-engineering process would be followed in an attempt to improve results. The prevailing stoping practices were scrutinised and the possible causes were listed.Some of the identified causes were design, drilling accuracy, equipment condition, mucking practices and direction of firing. It was identified that in most instances the underbreak was initiated in the slot area of the stope during the first firings. Once this happened, it was impossible to get good recoveries on the rest of the stope. The slot area was carefully scrutinised and the blasting practices were changed individually.During the following two years several different strategies were trialled to increase the toe recoveries. The results indicated an overall improvement of six per cent reduction in underbreak on average, by ensuring drilling accuracy and changing the direction of firing. The economic significance of these results outweighed the time and additional work load expended to establish the cause of the problem. This paper outlines the continuous improvement process undertaken to identify and rectify the major contributing factors to the problem. It also presents a set of recommendations to be followed in order to achieve positive results.

Mar 21, 2011

By P Sha

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Elaine Dorothy Cu-Au (REE-U) skarn deposit in the Mt Isa Inlier, Queensland, Australia is characterised by extensive metamorphic calc-silicate hornfels long before hydrothermal skarn and complicated deformation history. The deposit is hosted by the Corella Formation (1780–1740 Ma) and exhibits two phases of skarn formation in the study area – banded fine-grained diopsidic hornfels (Phase 1) and coarse-grain pyroxene skarn (Phase 2). Phase 1 skarn is predeformation and is interpreted to have been caused by the 1743–1734 Ma Burstall Magmatic Suites, whereas the coarse-grained pyroxene skarn (Phase 2 skarn) postdates the deformation and peak metamorphism events. Phase 2 skarn consists of prograde pyroxene, less garnet and titanite, retrograde epidote, REE-allanite, amphibole, biotite, and later sulfides, carbonate, quartz, anhydrite and chlorite. It hosts most of the copper mineralisation, with the REE elements occurring mostly in allanite. Titanite coexisting with allanite and Cu-Fe sulfides in Phase 2 skarn has been dated by laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) at 1524 ± 9 Ma (207Pb/206Pb). The ages are similar to Williams-Naraku Batholiths, which outcrop approximately 40 km to the east in the Eastern Fold Belt. In Elaine Dorothy, the isotopic compositions for calcite cluster around 12.2‰ d18O and -3.7‰ d13C. It probably resulted from a mixing processes between marine sourced carbon-oxygen (ca 20‰ d18O and -0.5‰ d13C) and other distinct geochemical reservoirs, eg magmatic C-O. These features indicate that Phase 2 skarn and Cu-Au (REE-U) mineralisation may be related to unexposed intrusions at deeper levels.CITATION:Sha, P, Spandler, C and Chang, Z, 2015. Elaine Dorothy Cu-Au (REE-U) skarn deposit, in Proceedings PACRIM 2015 Congress, pp 445–450 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By J Theiler, B Beamish

The presence of reactive metal sulfide minerals in waste rock contributes to the hazard of spontaneous combustion in dumps, as these minerals react with air and water entering the dump at ambient temperatures to form various mineral products and significant heat. This reaction series can also be an initiator of self-heating of carbonaceous material present in the waste rocks if sufficiently high temperatures are reached. Characterisation of these reactive minerals has primarily been to assess the risk of acid mine drainage, which is not necessarily an indicator of spontaneous combustion risk. No systematic testing procedure has been adopted by industry to assess the spontaneous combustion propensity of the waste rock. As a consequence, the principal management strategy for spontaneous combustion has been a reactive approach of dealing with events as they arise.Recent advances in adiabatic oven-testing have enabled more definitive assessment of the spontaneous combustion propensity of coals, including the quantification of the accelerating influence of reactive pyrite (Beamish and Beamish, 2011, 2012; Beamish, Lin and Beamish, 2012). This same test procedure has been used to assess the self-heating performance of metal concentrates and is therefore amenable to assessing the metal sulfide oxidation process from low ambient temperatures. The data obtained from such testing can be used to quantify the more prone waste rock sequences of a mineral deposit in advance of mining. This enables appropriate management planning for emplacement and long-term storage of waste rock in dumps.CITATION:Beamish, B and Theiler, J, 2016. Characterising the spontaneous combustion propensity of waste rock, in Proceedings Life-of-Mine 2016 Conference , pp 93–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Smallnone P, Walker B

Mining of the AKI lamproite pipe at the Argyle Diamond Mine (ADM) commenced in 1985. Originally designed to mine ore at a rate of 3.6 Mt per annum, the project has gone through two major plant expansions to a designed production rate of 8.7 Mt

Jan 1, 1998

By D Shuen, R Sales, D La Rosa

Semi-autogenous grinding (SAG) mill control is complex and depends on many dynamic process variables. Good control strategies ensure that a mill is operating as close to optimal as possible, resulting in significant economic benefits to an operation. Pueblo Viejo, a gold mine in the Dominican Republic, has been actively improving their control strategies since start-up in 2012, and one of these initiatives was to install an acoustic monitoring system on the SAG mill. The data from the system is used to optimise the mill’s performance by limiting the time the mill is either running too quiet or too loud. The lower limit is an indication that the charge in the mill is too high for efficient breakage or that the mill speed is too low and grinding media are not striking the toe of the charge. Conversely, when the acoustic emissions from the mill are too high, this can indicate that the balls are striking above the toe of the charge, resulting in inefficient grinding and excessive liner and lifter wear. Adjusting mill operating conditions to keep acoustic emissions in the ‘sweet spot’ between these limits results in more efficient grinding.Pueblo Viejo installed a Metso SmartEar™ to monitor the acoustic emissions of their SAG mill in January 2013. This system has been installed on many mills around the world and is specifically designed for optimising SAG mill control. One system output is the impact counter which measures steel-on-steel impacts on the mill shell. The impact counter uses both frequency and time domain analysis to approximate the number of ball impacts per minute. This method of analysis excludes parts of the sound signal not associated with steel-on-steel impacts and gives an accurate measure of this critical control parameter. After the acoustic system was installed, Pueblo Viejo collected data to determine the upper and lower limits for the impact count variable. The live data is available to the mill operators and it is used as one of the key operating variables to control the mill.Through continuous improvement and the use of advanced technologies like SmartEar™, Pueblo Viejo are improving the control and operation of their SAG mill, resulting in reduced liner wear, more efficient mill performance and optimised energy consumption. This paper discusses the installation of the system, and the measureable benefits obtained by using acoustic monitoring to control their SAG mill.CITATION:Shuen, D, Sales, R, Wortley, M and La Rosa, D, 2014. The benefits of using SmartEar™at Pueblo Viejo, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

The basic make-up of the majority of currently produced bulk explosives has changed little in the last 20 years. These explosives would be described as mature in a life cycle analysis. Therefore these explosive products and the practical rules for their use are well understood and well established. In recent years there has been interest in low density explosives, predominantly due to ammonium nitrate shortages and the associated increase in the cost of explosives. In the use of low density explosives some of the practical rules for the more commonly used bulk explosives do not apply. Therefore a shift in the thinking among users is required. At a number of mines low density explosives have been trialled or are being used, utilising the practical rules that apply to bulk explosive products. This has led to poor blast results in many situations. These poor blast results have often then led to a reduction in the use of low density explosives at the mine. This reduction does not acknowledge the advantages that can be gained from this product in the area of reduced cost of mining. This paper looks at low density explosives and discusses how and why these products work. Included in the paper are some practical ideas and examples of how low density explosives can be effectively used at the mine site.

Jan 1, 2007

This paper talks about the experiences of groups we have worked with over the last few years in the Asia-Pacific region (Australia, Canada, New Zealand and Papua New Guinea) and the ways that they have worked to bridge the divide between traditional and introduced structures, governance at a regional level and the introduction of traditional values into monitoring and evaluation practices. In doing this these groups have created structures and processes which have helped them engage both more effectively with external stakeholders while maintaining the legitimacy of their own operations with their own constituents. These are important ideas for those involved in the mining industry that could provide a number of very tangible benefits to mining firms and their engagement with these kinds of groups.

Jan 1, 2009