Search Documents

Particles of a complex nickel sulphide concentrate (containing pyrite, pyrrhotite, pentIandite, and violarite as the major mineralogical constituents) were entrained in a stream of hot gas the temperature of which was varied from 500 to -1000°C. Chemical analysis of the particulates collected from the furnace was used to detect the rapid change in sulphur content which accompanied the ignition temperature jump. X-ray diffraction analysis was used to characterize the oxidized material.These techniques showed that ignition was dependent on the mineralogical composition and occurred over the temperature range 500-900°C. Pyrite ignited first in the range 500-600°C; pyrrhotite was the least reactivemineral and required temperatures in excess of 800°C for ignition. The nickel minerals <pentIandite and violarite decomposed before ignition and ignited at temperatures intermediate to those required for the pyrite and pyrrhotite. The ignition temperature for the pyrite was found to be independent of particle size and concentration of oxygen in the atmosphere.Ignition temperatures determined by the simulated flash smelting method were compared with the results of differential thermal analysis (DTA) measurements performed on the same concentrate. Temperaturesdetermined in the DTA test as corresponding to the start of exothermic activity were shown to be at least 100°C below those determined by the simulation test.

Jan 1, 1978

By Parkhurst D. H

It is shown that a differential colorimetric technique can be used as a routine method for the estimation of titanium in beach sands, and their ore dressing products. The method will tolerate the presence of most of the other elements usually found in beach sands. The accuracy is shown to be within the limits of ±0ò31 per cent for concentrates containing more than 95 per cent titanium dioxide and ±1 per cent for tailings containing 0ò2 per cent titanium dioxide. The method is described for use with a Hilger "Spekker" absorptiometer.

Jan 1, 1957

By B Murphy

Traditionally comminution optimisation has been focused on energy minimisation, whereas flotation optimisation has been focused on recovery improvement. One of the largest, if not the largest, operating cost over the life of a flotation circuit is electrical energy. With increasing pressure on operators to lower production costs and the cost of energy increasing, reducing the energy consumption of the flotation circuit can be beneficial to site economics. This paper reviews the use of energy by mechanically agitated flotation machines and discusses the measurement and benchmarking of energy consumption in modern flotation concentrators. Opportunities for improving flotation energy efficiency are also identified.CITATION:Murphy, B, 2013. Flotation energy consumption and opportunities for improvement, in Proceedings MetPlant 2013 , pp 399-412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

Techniques Used and Problems Encountered in Normal and Reverse Circulation Drilling at the Mt Roseby Project, Cloncurry, North West Queensland

Sep 13, 2010

By P Craig, M Holden, C Zhang, D Foster, J Oh, S Saydam, J Liu, H L. Ramandi, S Akdag

High stress in rock masses can cause significant instability problems such as squeezing deformation in soft rock and rock bursts in hard rock. The support system applied in burst-prone areas in high-stress conditions is required to be able to carry high load and accommodate large deformation of the rock mass without experiencing any serious damage. Yielding support systems are promising to provide support for both squeezing and burst-prone rock mass encountered in mining or tunnelling at depth. They are ideally strong and stiff initially and then ductile after yielding (Potvin and Hadjigeorgiou, 2020). With respect to support design, a ground support system has to create a safe working environment under both static and dynamic loading conditions by providing the functions of reinforcing, retaining, holding and connecting elements (Cai and Kasier, 2018). Rigid rock bolts and cable bolts perform reinforcing and holding functions of a ground support system. In highly fractured ground or with large excavation spans (eg at roadway intersections or in caverns), unstable ground depth can exceed the length of typical rigid rock bolts (ie greater than ~3.0 m). In such cases, flexible cable bolts are needed to tie the reinforced and retained rock mass back to deeper and more stable rock. The flexibility of cable bolts allows anchor lengths greater than the tunnel opening that would otherwise restrict rigid bolts. Cable bolts also offer higher strength to weight ratio, with tensile strengths 2–3 times that of standard rebar bolts. This high strength comes at the cost of lower strain tolerance, typically around 5–7 per cent at break. Despite the lower strain tolerance, cable bolts are often used as dynamic support in demanding burst-prone ground conditions. The lower strain tolerance is compensated by allowing sufficient free length for stretching or incorporating a yielding device. There are a number of dynamic cable bolts available on the market and a number of testing campaigns have been undertaken to quantify the dynamic performance of these cable bolts. This paper reviews the existing range of dynamic cable bolts and discusses the potential areas for improvement and further research.

Nov 29, 2022

By P Goblet, S A. Séguret, E Cordier, A Galli

In salar-type deposits, lithium grades can be measured by bailers introduced at different elevations in the drill holes at locations where, later, the brine will be pumped out to recover the metal. When they are duplicated, these a priori rudimentary measurements may show large differences without indicating whether this is due to the procedure itself or to some physical causes linked to the dynamic behaviour of the salar (seasonality, rainfall, underground flow etc). In the reservoir presented in the paper, the problem is complicated by the double lack of stationarity of the lithium grades: the grades not only increase importantly with the depth but at the same time their fluctuations decrease, making it necessary to use non-stationary geostatistical techniques to simulate them. Reservoir simulation is developed in two steps: first, geostatistical simulations of the lithium grade create possible realisations of the reservoir; then, each geostatistical simulation is followed by a pumping simulation that calculates, at each drill hole of a given extraction scenario, the lithium produced each year over 40 years. For the set of 100 simulations produced in this way, a scenario reduction is made to choose the five most representative simulations where more complex calculations will be carried out (for example, changing hydrogeological parameters such as porosity and permeability, or the elevation of the filters, the number and the location of the pumping and the reinjection drill holes etc). The paper first presents an analysis of the geostatistical model sensitivity to the grade uncertainty when measured by bailer. Among the 100 measurements at our disposal covering the future production domain, 50 per cent are duplicates measured at the same place but at different times. They are randomly sampled to produce five subsets of 75 values, which will constitute the future 3D conditioning points for the geostatistical analysis and the simulations. For each subset, trend, standard deviation and variogram models are fitted, leading to five sets of 20 geostatistical simulations of grades. In this way, the reliability of the different parameters involved in the procedure is evaluated, as well as its impact on the pumping results. Then, a reconciliation study is conducted between the non-stationary nugget effects encountered in the 3D variograms of the lithium grade and a pure statistical analysis of 25 duplicates measured at different locations and/or different times. The result is that if the nugget effect reaches 20 per cent, which is the case of three conditioning subsets out of five, the reconciliation is good and the nugget effect of the variogram model represents the bailer uncertainty, ie the measurement error. Since the geostatistical simulation incorporates a nugget effect, it handles the bailer uncertainty and the impact on the produced metal is included in the evaluation. The final conclusion is that, after the hydrogeological pumping simulations, the initial differences between the five geostatistical models do not influence the final results: lithium grades measured by bailers can lead to a robust evaluation of the extractable resources, a conclusion that conflicts with conventional wisdom.CITATION:Séguret, S A, Goblet, P, Cordier, E and Galli, A, 2017. Bailer uncertainty evaluation in a lithium salar deposit, in Proceedings Eighth World Conference on Sampling and Blending , pp 395–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By J G Bastias

It is sometimes necessary to resort to extremes in order to call attention to something that is pertinent to safety in mining. When some of the experts in occupational safety talk about this topic, they usually refer to a 'regulation' established by the Romans which stated that, due to the health hazards, usually death, no Romans but only slaves should work in mining. Since the time of the Roman Empire, a lot of ground has been covered in the field of mine safety. Nowadays, it can be said that occupational safety is being seriously addressed, with the result that the number of mining accidents has reduced dramatically, fatalities in this industry are less frequent, and the rate of accidents compared with other activities, such as construction or fanning, is low. This achievement has been possible initially through government legislation and by procedures established by the mining companies themselves. However, the dilemma for government is whether to regulate and if so, how much. It is pleasing to observe that most companies are establishing working procedures which conform with new government legislation, placing strong emphasis on the duty of care for mine employees. There will always be some regulatory aspects of legislation, and perhaps the best example of this is in the use of mine hoists where there are no international or Australian standards, and the regulations applied are of an empirical nature that err on the side of safety.

Jan 1, 1994

By M Graham, R Brunning, C Andringa-Bate, S Westergren

In 2010, Rio Tinto Iron Ore’s operations commenced the planning and design of a sampling and analysis system for the new 50 Mt/a Cape Lambert Port B (CLB) facility. Current sampling systems at the ports consist of automated robotic, mass-based sampling protocols employed at Dampier, and semi-automated, time-based sampling systems operating at Cape Lambert Port A.The new sampling system at CLB has brought together a fully automated sampling and analysis system utilising time-based sampling, with the capacity to sample ore products of medium quality variation as defined in ISO 3082 (ISO, 2009). The CLB system is required to sample at shiploading rates from 6000 t/h to 13 440 t/h and provide full load-port analysis. The sampling approach is to proportionally extend primary increments (of varying mass relative to shiploading rate) to a standard length using variable speed aero-belt conveyor systems. This enables a fixed number of secondary cuts to be achieved for all primary increment masses and to be delivered to the automated cell. The cell is required to be capable of concurrently processing four individual shipments, each containing multiple cargoes.Achieving the target sampling precision for all export cargo sizes has culminated in the planning, design and construction of the largest automated iron ore port laboratory in the world. The CLB sampling and analysis cell was commissioned in Q3 and Q4 2013. This paper discusses the sampling philosophy and commissioning outcomes.CITATION:Brunning, R, Andringa-Bate, C, Graham, M and Westergren, S, 2014. Cape Lambert Port B shiploading, sampling and analysis, in Proceedings Sampling 2014 , pp 79–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By M Lee, J F. Carswell, G Reitsema

"The increased costs of underground mining have continually challenged engineers to identify opportunities for alternatives to common approaches to underground development. Considerations to the design of horizontal and vertical development at the Dugald River mine targeted inclined raise boring to reduce horizontal development, not only to reduce cost, but to allow development activities to focus on other areas of the mine.The mine plan consists of 50 raise bored ventilation shafts, of which 17 have been mined to date with diameters ranging from 3.1 m to 5 m and lengths from 30 m to 200 m. The expected performance and stability of these shafts has been determined using methodologies proposed by McCracken and Stacey (1989) and further refined by Peck, Coombes and Lee (2011). Actual raise performances have been collated and compared to a database of raise bore performances across Australia as presented by Coombes, Lee and Peck (2011), and form a database of raise bore performance specific to Dugald River.Opportunities to further optimise the mine plan and reduce costs have seen the introduction of large diameter-inclined raise bored ventilation shafts to minimise the required lateral development to connect the ventilation circuits. Large diameter inclined shafts ranging between 3.1 m and 4.5 m in diameter have been successfully mined with dips down to 70°, reducing the cost of lateral development by more than $1 million over the next two years.Both technical and operational challenges were overcome in the mining of large diameter-inclined raise bores, including modification of: existing methodologies of assessing shaft wall stability for inclined raises. These included variations of the McCracken and Stacey method and the utilisation of the modified stability number (N’) previously developed for stope performance (Potvin, 1988). both the collar and toe development profiles, including the general set-up of the raise bore drill rig to reduce the operational risks associated with angled raises.Due to their success, inclined raises have been designed for subsequent stages of the life-of-mine ventilation system at Dugald River. This has resulted in significant capital cost savings for the mine.CITATION:Carswell, J F, Reitsema, G and Lee, M, 2017. Vertical and inclined raise bore performance at Dugald River mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 313–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By S Liu, N M. Rana, A Take, N Ghahramani, D Clohan, S McDougall, S G. Evans, H J. Chen

Tailings dam breaches have caused significant life loss, social, economic and environmental damage in recent years. The term "tailings-flow" refers to various forms of tailings outflow movement resulting from the breach of a tailings dam. These flows, comprising a mixture of tailings, water and dam materials, can take different forms, ranging from a debris flood to a flowslide, and can travel long distances and impact large areas. The inundation extents depend on the failure mechanism, tailings dam height, total released volume, sediment concentration (associated with the rheological behaviour of the flow) and downstream conditions (including topography, land cover and presence of a water body). Numerical runout modelling of tailings dam breaches is important for predicting the dynamics and extent of tailings-flows, which are crucial steps in tailings dam consequence analysis and risk management. This paper presents a comparison of numerical simulations of the 1994 Merriespruit tailings dam breach using three numerical models: DAN3D, FLO-2D and MADflow3D. Using compiled site condition information and data from the literature and public domain, model performance was evaluated primarily based on comparisons between the observed and simulated inundation extents. The main purpose of this preliminary model benchmarking exercise was to help us evaluate the capabilities and limitations of each model, and to identify opportunities for future model improvements as part of a broader research initiative known as CanBreach. This exercise also highlights the inherent complexity of tailings-flows and the importance of using judgement to interpret model input and results.

Jul 1, 2021

By Edwards A. B

Occasional, sporadic and small occurrences of lollingite in the Broken Hill lode have been described,(l) mostly in the garnet sandstone in the foot-wall and under-wall of the Broken Hill lode. The lollingite contains appreciable percentages of cobalt and nickel and is regarded as an early mineral in the development of the lode; and, with the incoming of the sulphides, it has suffered considerable replacement by arsenopyrite. During the conversion of iron arsenide into the iron sulpho-arsenide, ilie nickel and most of the cobalt are removed in solution and are inferred to reappear in niccolite and other minerals that have been recorded among the later minerals of the Broken Hill lode. As a result of observations of the officers of ilie Broken Hill South Ltd., an occurrence of cobaltite can now be recorded which has developed by an analogous type of replacement.Cobaltite has previously been recorded from the Australian Broken Hill Consols lode in the vicinity of the rich deposits of silver, though not in contact with them. Cobaltite has been found in the northern extremity of the No. 2 lens of the Broken Hill lode at the 1,480 feet level of the Broken Hill South...

Jan 1, 1944

By A Remes, A Dennis, M Talikka, T Kotiranta, S Horn

A mine project combines vast amounts of information from various disciplines including but not limited to geology, mining, metallurgy, technology, environment and economics. In many cases, all relevant information is not fully shared between all disciplines. Thus, project performance (technical, economical and sustainability) may be evaluated on basis of insufficient information resulting in non-optimal decisions, project execution and risk management. Advances in computing power and simulation software enable various data sets to be incorporated in a single digital platform enabling more efficient and transparent data sharing. In addition, linked data sets and simulation can support assessment and optimization of the project as a whole rather than focusing on optimization of individual events. CITATION:Horn, S, Remes, A, Kotiranta, T, Talikka, M and Dennis, A, 2018. Evaluation of sustainability of copper production value chain from ore to metal using advanced simulation, in Proceedings Life-of-Mine 2018, pp 87–89 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By B Wu, C Zhao, B Lei

At present, the friction factor is calculated by measuring pressure drop and airway configurations. However, the workload of on-site measurement is heavy, and the measurement results are easily disturbed by the external environment. In order to meet the need of intelligent ventilation to quickly and accurately obtain the friction resistance of roadway. Based on the important of roughness in Atkinson friction resistance formula, in this paper, fractal theory is used to characterise the 3D rough surface, and a method based on fractal dimension to describe the roughness of roadway surface and calculate the friction resistance was proposed. A computational model of friction resistance for fractal characterisation of roadway 3D rough surface was established. The parameters of the model were deduced and verified by using Nikuradse experimental data. The fractal dimension of roadway surface was calculated by 3D laser scanning data of Kailuan roadway, the established friction resistance calculation method was compared with the field resistance measurement results. It is considered that the calculation method of friction resistance based on fractal theory is reliable and can well represent the influence of 3D rough surface characteristics of roadway. The result show that the new established friction resistance formula compared with the traditional Atkinson formula in Nikuradse experimental, the average relative error is 6.874 per cent, and compared with the measured results of ventilation resistance in Kailuan experimental roadway, the relative error is 6.667 per cent. Comprehensive evaluation and analysis suggest that the new formula can well reflect the influence of 3D rough surface on friction resistance, combined with 3D laser scanning technology, the friction resistance of roadway can be calculated quickly and accurately. This research provided a reference for the key technology and theoretical development of intelligent ventilation parameter measurement.

Oct 12, 2022

By J Pan

In this paper, the technology of producing fluxed pellets by using hydrated lime as binder instead of bentonite was carried out. The properties of the two types green balls (0.8 per cent bentonite and 2.0 per cent hydrated lime) were as follows: drop numbers of 4.8 - 5.0 times/0.5 m, compressive strength of 19.7 - 24.2 N/pellet and thermal shock temperature of 280° - 385°, respectively, under the same conditions of 1.5 per cent coke, 1.45 basicity and balling at 8.5 per cent moisture for 13 min in disc pelletiser. Comparing with bentonite as binder, the compressive strength of fired pellets with hydrated lime is elevated by 13.8 per cent and climbs up to 3113 N/pellet under the following conditions: preheating at 1050°C for ten minutes and fi ring at 1300°C for 15 min. In the mean time, the hydrated lime also improves the metallurgical performance of fired pellets. The reduction index was enhanced from 68.6 - 70.6 per cent, RDI+3.15+ increased from 90.1 to 98.8 per cent and reduction swelling index dropped from 22.4 - 7.4 per cent, respectively. The mineral compositions and microstructure of fi red pellets shows that the fired pellets containing 2.0 per cent possess more calcium ferrite and magnesium ferrite and compact microstructure, leading to the higher compressive strength.

Jul 11, 2011

By Clifford C. E

The Black Star and Racecourse orebodies below 15 level contain a major portion of the primary silver-lead-zinc ore reserves of 56 million tonnes at 150 g/t Ag, 6.4% Pb and 6.5% Zn at Isa Mine. Extraction from this area is scheduled to begin in the early 1980's. Mining in this block will be quite com- plicated as the ore is contained in a dozen separate orebodies varying in width from 3 m to 20 m with only narrow barren pillars between them in some cases. Mining objectives which consider metal recovery, costs, environmental and safety factors, operating requirements and rock mechanics are used to compare proposals. The planning work involved in formulating mining proposals considers disposition of reserves, scheduling factors, sequence of extraction, extraction methods, haulage set-up and ventilation requirements.

Jan 1, 1979

This paper examines some of the fundamental economics of mining - in particular, for optimisation studies, for production rate determination and for reserve estimates.It includes introductory discussion on the principles as to how economics drives mining investment decision-making, applicable to the optimising of pit shapes and production, or truck fleets, or any other part of the mine.The main part of this paper looks at the decision to start-up a mine and why the 'optimum' production rate to start-up a mine is not the point of lowest cost according to traditional discounted cash flow (DCF) analysis. The optimum production rate is usually substantially less than this rate. The paper recognises the difference between typical mining investments and investments in other industries that do not have the unique characteristics of mining and the problem of uncertainty resolution. It examines the marginal revenue effects, the marginal cost of capital and the value of a real option to expand pending uncertainty resolution as determinants of optimum initial production rates.The final part of this paper looks at applying these principles to renewable and non-renewable resources. It examines mine life and reserve estimates from an economic perspective.

Dec 6, 2010

By D Craw, C E. Martin, C Smith, C Rufaut

Wangaloa Coal Mine opened in 1945, and by the time of its closure in 1989, had produced 750 000 tonnes of coal and disturbed an area of 75 ha. The original mining licence required land rehabilitation to exotic forestry, however the current owner, Solid Energy, has worked with Crown Minerals and local councils to write a new rehabilitation objective. The site is now being stabilised and replanted with native species, and may be available for public use before the coal mining licence expires in 2007. Site discharge permits expire in 2017, and by that time, it is anticipated that discharge water chemistry will be similar to background levels. MWH are currently contracted for management of the mine rehabilitation project. The Kaitangata coal unit mined at Wangaloa is sulfurous lignite with associated pyrite. Kaitangata coal contains 3.2 wt per cent sulfur, which is higher than most New Zealand coals. Initial analyses at Wangaloa indicate low pH (2.56.2) values in soil, groundwater and surface waters as a result of acid rock drainage (ARD) processes, leading to increased metal mobility and challenging conditions for vegetation. Pilot studies indicate pinus radiata needles contain up to 67 mg/kg boron, and elevated As, Cu and Zn concentrations in surface waters. The main lake at the site has a pH of approximately 4.9, despite lime dosage in 2002. There is a real need for a complete geochemical model of the Wangaloa coal mine. Such a model could be applied to similar restoration projects, and would assist by pinpointing geochemical processes and toxic metal relationships most harmful to the receiving environments. Using this model, rehabilitation in the future will be targeted and more efficient. This project is part of a larger scheme to characterise and model the Wangaloa mine site restoration, including waters, soil, vegetation, geology and invertebrates.

Jan 1, 2003

By J Furtney, W Fu, D Nutakor, A Brose

Rock blasting outcomes are often a shared responsibility of both the mine operations group and the mine geotechnical group. From an operational logistics and planning perspective, blasting concerns include optimal fragmentation for subsequent crushing, ensuring the blast is energetic enough to allow easy digging, and understanding the effect of muck from a previous blast on the current blast. From a geotechnical perspective, wall damage and catch bench capacity are the primary concerns. Other concerns for both teams include damage to mine infrastructure by fly rock or blast-induced vibrations, and the stability of open stopes under the pit. This work presents two blast modelling applications (or ‘apps’). The basic app instantly gives fragmentation and wall damage predictions for a given generic blast design. The advanced app loads the current pit contours, reads the blast design from a spreadsheet, and calculates the expected vibration magnitude and peak frequency. The apps have been developed specifically for the Rio Tinto Borates and Lithium Mine in California and are used to support blast design between the operations group and geotechnical group. The basic app instantly gives fragmentation and vibration predictions given a blast design by combining the Kuz-Ram fragmentation model with the scaled distance model for vibrations. The advanced app uses the signature hole method. Blasting outcomes at the mine have improved since using the apps.

Jun 22, 2022

Fire suppression systems are now recognised by both NFPA 502 and PIARC as legitimate tools for both life protection and asset protection. The effectiveness of these tools for life protection demands extremely rapid and accurate incident detection coupled with rapid response. This rapid response must be integrated with other emergency systems such as emergency ventilation. The March 2007 fatal Burnley Tunnel incident in Australia graphically illustrates the potential of effectively integrated fixed suppression systems to protect people from harm and save infrastructure from damage. Despite the raft of technology available in that instance to the operator it was the human operatorÆs ability to effectively control the emergency equipment and not the equipment itself which so positively influenced the threat to life and property.

Jan 1, 2008

Treatment of Gold-Bearing Oxide High-Clayish Ores The analysis of modern state of treatment technologies of gold-bearing oxide high-clayish ores showed that the main method applied both in Russia and abroad is sorption leaching and heap leaching with preliminary granulating. The use of any of these processes depends on many factors including average gold grade, site and area of a deposit, clay content and etc. The two processes are often used at the same deposit. In this case, rich ores are treated according to a plant technology, poor ores and ores with cut-off grade are treated with heap leaching. Both technologies possess their own advantages and disadvantages. A plant technology is characterised by high recovery with higher capital and operating costs at the same time. Lower recovery during heap leaching can be attributed to an unstable quality of ore granulating due to both technological and weather conditions. In case of poor high-clayish ores, the use of a combined ore treatment is possible and profitable. It includes the ore disintegration and a clayish fraction treatment by using a heap leaching. In this case, capital and operating costs reduce in comparison with a plant technology and the recovery increases in comparison with heap leaching. Sometimes it reaches a plant recovery. These ores possess special features. As a rule, gold is associated with ore fraction, so it liberates readily from the association with ore ore-forming minerals even with relatively coarse grinding explain their high solution velocity in a hydrometallurgical cycle. Clayish ores are characterised by high sorption activity to gold cyanide complexes as well as extremely low velocity of filtration and thickening of slimic pulps at the same time. The paper describes the options of oxidised high-clayish ores treatment, such as, a plant technology (PIP and CIP process), heap leaching and a combined technology (disintegration, heap leaching of a crystalline fraction and sorption cyanidation). The obtained results were used when selecting a treatment technology and during construction of a plant for oxidised high-clayish ores treatment.

Sep 13, 2010