Search Documents

Fine Gravity Separation in the Reflux Classifier, Exploiting a High Shear Rate, Laminar Flow Mechanism The Reflux Classifier is used in the gravity separation of particles over a broad range of particle sizes. The device consists of a fluidised bed zone, with a system of parallel inclined channels above. The inclined channels provide a significant hydraulic advantage over conventional fluidised beds via the so-called Boycott Effect (Boycott, 1920). This paper describes a new advance in fine gravity separation based on the high shear rate and laminar flow profile that arises when closely spaced inclined channels are deployed. As reported recently (Galvin et al, 2009a), a powerful density based separation mechanism develops from this arrangement, suppressing the effects of particle size. In this paper we focus on two areas, firstly the application of the separator in the laboratory for batch fractionation of particles of varying size and density to determine the grade recovery curve and hence the liberation, and secondly the step change in separation performance achieved on a continuous steady state basis when closely spaced inclined channels are used. The variation in the separation density with particle size decreases significantly, and the Ecarte Probable Error (Ep) remains at low levels over a broad size range.

Sep 13, 2010

By D J. Bradshaw, E M. Wightman, C L. Evans, B Triffett

During the commissioning phase of Prominent Hill, periods of reduced recovery were experienced with higher-grade ore blends. This was unexpected and as part of the process to identify the cause, surveys were conducted in May 2009, with two different ore blends (copper grades: 1.94 per cent Cu (blend 1) and 2.49 per cent Cu (blend 2)). Metallurgical performance was assessed in terms of rougher recovery and grade with consideration of both pulp and froth effects. In addition, hydrodynamic measurements (gas hold up, bubble size, superficial gas velocity) as well as measurements of bubble load and top-of-froth grade were taken during the surveys and full mineralogical assessment of selected streams completed to characterise the nature of the differences. The metallurgical results showed that the lower performance was obtained with blend 2 which contained the higher amount of chalcocite and was higher-grade. Analysis of the survey data showed that for both ore blends more than half of the copper loss occurred in the +38 ¦m size fractions. Almost 30 per cent of the copper in the +38 ¦m fractions that reported to the rougher tails during processing of blend 2 was liberated compared to less than five per cent for blend 1. Additionally almost 60 per cent of the copper in the +38 ¦m fraction of blend 2 was chalcocite compared with approximately 20 per cent in blend 1. This paper discusses the sensitivity of the chalcocite-to-surface chemistry effects causing marked reductions in recovery either through reduced pulp recovery or froth phase (detachment) effects. The reagent suite and operating conditions were subsequently changed and the recoveries increased substantially and the sensitivity to ore changes eliminated. It should be noted that subsequent optimisation work, which focused on recovery improvement, has led to copper recoveries of over 90 per cent being achieved.CITATION:Bradshaw, D J, Wightman, E M, Evans, C L and Triffett, B, 2012. Characterising the reasons for the difference in performance of two ore blends in early processing at OZ Minerals Prominent Hill Operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 273-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By S McKnight, L Koroznikova, S Hall

Mineral sands represent an important new resource being developed in the Murray Basin, including parts of western Victoria. This paper will outline a simple methodology for mineral sands characterisation, developed as part of the AMIRA-managed project P777 æThe Development of Heavy Suspension Techniques for High Density Separations (Replacement of ClericiÆs Solution)Æ. This project is currently sponsored by three multinational mining companies (De Beers Consolidated Mines, Iluka Resources Limited and Rio Tinto Limited) and is developing an innovative laboratory mineral characterisation procedure that will allow the replacement of the currently employed highly-toxic chemicals.Mineral sand resources almost always contain more than one valuable (and relatively heavy) mineral. Titanium minerals are found with a large range of titanium contents, giving rise to density variation and often subjective mineralogical descriptions. Companies tend to rely on laboratory heavy liquid separation in the evaluation of samples arising from exploration, mining or metallurgical processes. Unfortunately, there are only a limited number of high density (æheavyÆ) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilised at relative densities (RD) up to 3.0. However, beyond this value currently only organic liquids can be used. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used; however, this presents significant health and safety hazards. Mixtures of thallium formate and thallium malonate were found in the early 1900s by Clerici to provide liquids having specific gravities between 4.0 and 5.0, hence æClericiÆs solutionÆ. For the characterisation of the heavy components of mineral sand deposits (eg anatase sg 3.9, rutile sg 4.2, ilmenite sg 4.4 û 4.7 and zircon sg 4.6 û 4.8) there is currently no heavy liquid alternative to ClericiÆs solution. ClericiÆs solution is highly toxic and testing is now conducted by very few laboratories worldwide with costs reflecting the chemical costs (though extensive efforts are made to recover and reuse the liquid, plus the requirement of its removal from the mineral samples), the infrastructure costs and health and safety regimes (eg blood testing of exposed staff, inventory management). A simple laboratory technique of density fractionation is being developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstate (LST) solutions, that can replace ClericiÆs solution in the evaluation of fine mineral sands samples (eg -250+150 microns). The developing methodology that can achieve low-cost, low-toxic separations at relative densities above 5.0 will be outlined and the comparison of results with ClericiÆs solution presented.

Jan 1, 2006

The key to the successful debt funding of a new mining project, whether in economically established or developing nations, is the submission of a comprehensive feasibility study. The feasibility study forms the basis from which the resource banker can construct financial models which govern the amount of available funds, the conditions which control the supply of such funds and the time period over which the loan may be repaid. The bank will wish to ensure that the feasibility study is the best representation and confirmation of reality possible because this model is the basis of the loan security package. Thus the study will be vigorously interrogated by independent experts in all its elements including the ore reserve, mineability, metallurgy, operating and capital cost profile, environmental factors and management. A well constructed feasibility study, undertaken by well recognised and respected independent consultants can save the client company a great deal of real and opportunity costs especially in relation to project timing. Once constructed and operating, the mining project may face one or more completion tests in relation to the loans provided. The genetics of such tests often relate to either the ability of the operating company to become solely responsible for the repayment of the loan or to be rewarded by lower interest rates or some other mechanism. Strong professionalism, accessible records, good checking procedures and high quality, competent site management will greatly assist the client company passing these tests. A record of well established technical competence with its bankers may well assist a company in the establishment of a mezzanine loan for the early development of its next project, thus allowing an earlier return of dividends to shareholders.

Jan 1, 1995

This backgrounds the methods, and technical terminology, of digital image processing techniques used to write out remote sensing imagery.

Jan 1, 1983

Mine Dewatering for reoccupation of a flooded mine requires rehabilitation and recommissioning of shaft and sane level functions to provide safe efficient access, services and logistics, as well as securing connections with all exposed workings. The objective is the earliest secure reoccupation of the target depth horizon for minimum water pumping, consistent with an appropriate investment and optimum schedule of operating inputs to the dewatering, redevelopment, services and consolidation processes. Strategy must focus on recommissioning of relevant functions in the shaft and at stage pumping horizons, advance of logistics close to pumping and rehabilitation, management of the secured exposed workings. The progress must be systematic, sustained and integrated, and must be secured against risk and uncertainty. There must be a strategic capability to respond effectively, and manage interruptions to processes, conditions requiring higher or different resources, and contingencies which affect schedule, budget or risk profile for the continuing programme. Planning must aim to reduce or contain risk or uncertainty elements and contingencies, limit interruption frequency and severity, identify and provide the capability for efficient responses. It is appropriate to model and simulate the reoccupation analogous to a mine initial development production programme. Only minor changes to relationships and relativities of models for Capital works, Operations (Production and Development) and Services/Logistics are needed but the model for management of workings is more relevant than that for depleted workings in an operating mine because of the water and other transfers. An important difference is the unsteady state of operations which requires probabilistic modelling of availability and utilization of equipment and processes.

Jan 1, 1988

By A Deakin

It has been almost a decade since the release of the International Council of Mining and Metals (ICMM) Health and Safety Critical Control Management: Good Practice Guide (2015a). During this time the ICMM member companies, along with many others across industry, have been busy designing, deploying and enhancing their own critical control management (CCM) programs. So, what have we learnt? This paper discusses the scope, application and learnings from the implementation of CCM within the mining industry. What’s going well? What are the common challenges? What are the opportunities to strengthen the approach? What are the threats to successful implementation? The paper draws on the author’s experience as one of the key contributors to the development of the CCM Good Practice Guide and an adviser to many mining companies, including six of the ICMM members. The paper focuses on the practical (operational) application of CCM and the cycle of identifying, defining, implementing, verifying and improving critical controls at the frontline. The paper also includes a discussion on the safety performance of the ICMM member companies over the past decade and provides a recommendation for how CCM can be incorporated into a more proactive model to measure safety performance. The paper concludes with practical recommendations that mining companies, regardless of their CCM maturity, can consider as they look ahead. They are supplemented by three additional recommendations for consideration at the industry level.

Apr 16, 2024

By A R. Penney

Since mining-induced seismicity first became apparent at the Beaconsfield Gold Mine in 2002, there has been an ongoing program of geotechnical investigations to understand the phenomenon and allow for the development of strategies to manage the risks it posed to personnel, the business and the community at large. Studies resulting from a seismically induced rockfall on Anzac Day 2006 have been extensive, and have advanced the understanding and management of seismicity at the mine. Enhancement of the mineÆs seismic array, implementation of extensive monitoring of ground behaviour, improved ground support and reinforcement design, and ongoing numerical modelling provide a technical framework for the management of seismicity. In addition, extensive involvement of the workforce in risk assessment and the development of standard work procedures (SWPs), has contributed to a æbest practiceÆ approach to manage seismic hazards at the mine.

Jan 1, 2008

By R Thompson, J Miedecke, D Handel, E Tomicek, D Tulloch

"The Mine Haul Road Optimisation Alliance (HROA) is a unique Australian industry–academia collaboration that has been developed to support mine haul road operators. The alliance integrates industry, end-user service providers and academic research expertise in mine haul road design, construction and operation to identify, quantify, implement and monitor the various equipment, materials and road management strategies and solutions required to drive haulage productivity improvements.Initially, a broad overview of the university–industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis internationally. This insight places into context the opportunity that strategic collaborations present, to drive productivity and efficiency in mining, while also delivering innovative technology solutions.Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry collaborations can deliver a more robust and needs-driven solution to mine haul road design, performance and management, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service providers alike form the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and practical, implementable solutions.The paper concludes with examples of how the alliance collaborations work in practice to deliver focused mine haul road research outcomes, together with the mechanisms used to ensure industry needs are met through end-user driven research solutions for enhanced operational performance.Citation:Handel, D, Miedecke, J, Thompson, R, Tomicek, E and Tulloch, D, 2016. Driving Haulage Productivity Improvements through Industry–Academia Collaboration, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 243–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

An investigation into the causes of variable sulphur content in blast furnace metal produced at No. 4 blast furnace at the Port Kembla works of Australian Iron and Steel Pty. Ltd. was carried out. Theprogramme included an extended and detailed experimental study of a great number of the operating variables of the furnace, on a cast-bycast or four-hourly basis, over fourteen days.Possible causes of the variation were found in irregular operation due to sinter variability, and it was also clearly shown that slag conditions were most important in controlling sulphur contents of pigiron. Some decrease in sulphur variability was achieved, arising partly from this investigation, and it is hoped to try magnesia additions to modify slag conditions for better desulphurizing.INTRODUCTIONSulphur in pig iron is a problem common to many blast furnace operators throughout the world, but the direct causes and means of overcoming them are functions of the available raw materials, and are hence more particular to each plant and its operating practice. Sulphur in hot metal influences the steel-making operations, the rolling operations and the quality of the finished steel. The main problem associated with high sulphur in steel is "hot shortness", which leads to cracking of ingots and billets in rolling, to poor surface finish and to poor welding properties in the finished steel. On the other hand, sulphur is sometimes a desired additive to steel in order to promote free machining properties.Normal means of controlling sulphur A small degree of control of sulphur in steel is available to open hearth operators by alteration of slag volumes and basicity, but any large degree' of sulphur elimination is...

Jan 1, 1961

By D S. Collins, Z Hosseini, I Pinnock, Y Toya

Microseismic monitoring is regularly used in the mining and geotechnical industries to provide detailed information about rock mass response to operational activities. This paper implements a variable 3D velocity model (VM) at a North American hard rock mine with the aim of further improving the accuracy of seismic event locations. A collapsing method is also used to help analyse two individual seismic event clusters at another North American hard rock mine. In the first case study, the location accuracy of events is shown to improve by moving from a conventional single VM to a variable 3D VM that accounts for voids and different geological domains. The modal average for the event location accuracy improved from 14 m to 5 m when the 3D VM was used. Additionally, the single VM failed to locate 26 per cent of the seismic events that were located by the 3D VM. In the second case study, the distribution of seismic events was further enhanced by using a collapsing method that highlighted planar structures. The collapsing method was performed on two large event sequences that occurred in close proximity and identified different seismic event distributions. One aftershock sequence aligned along a plane, suggesting an activated structure, while the other large event sequence had a more 3D distribution of events, suggesting a complex stress redistribution on smaller structures.CITATION:Pinnock, I, Collins, D S, Toya, Y and Hosseini, Z, 2016. Large event sequence analysis and 3D velocity models for seismic event location accuracy, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 879–884 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

An Integrated Solid Waste Management Method for Western Macedonia, Greece

Sep 13, 2010

Spreadsheet Based Modelling of Liner Wear Impact on Charge Motion in Tumbling Mills

Sep 13, 2010

Efficacy of Enhanced Gravity Separator in Processing Indian Iron Ore Slime The slime sample was subjected to concentration using Falcon concentrator for their enrichment. The effects of three important variables, eg bowl rotation frequency, back water flow rate and per cent solid were studied on the process performance. Increasing the rotation of the Falcon bowl, enable more material to the underflow by increasing the yield, whereas, the iron content decreases steadily with increasing the rotation of the bowl. The increase in the back water flow effectively removes the clay materials from the underflow at the expense of the yield. Similarly, increasing the per cent solid concentration in the feed produces a better product both in terms of yield and Fe content. Results show that EGS/Falcon can be used for processing Indian iron ore slime and producing pellet grade concentrate.

Sep 13, 2010

It is no longer adequate when starting a new mine to simply select the best equipment. Today's competitive international commodity markets demand superior efficiency which requires systematic involvement of people in continual improvement of production and commercial processes. True Total Quality of Management (True TQM) principles provide an operating philosophy for maximising productivity and minimising unit costs of output. The presentation will show the practical and successful use of these principles. This paper will introduce the case study and provide background material on True TQM.

Jan 1, 1995

By S C. Dominy

This contribution examines the effect of feedstock sampling before the sorting stage of polyethylene terephtalate (PET) bottle recycling. Batches of waste PET bottles may contain non-PET bottles which need to be removed by sorting. Any residual presence of PVC is detrimental for the quality of products manufactured from recycled PET. The maximum tolerated concentration of PVC in cleaned PET is extremely low, which places high demands on the recovery of PVC achieved by sorting. To be confident of attaining the desired PET quality after sorting, acceptance sampling of truckloads of PET bottles may take place prior to sorting. It is shown that accounting for sampling uncertainty requires that the sorting process achieves a consistently high recovery of PVC bottles.CITATION:Glass, H J and Dominy, S C, 2017. Plastics recycling and sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 129–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Laboratory-Scale Magnetohydrostatic Separator for High Resolution Density Analysis of Plastic and Other Wastes Recycling and reuse of different plastic wastes is still a current problem to solve for process engineers and it is true for seeking industrial applications as well as for smaller laboratory-scale, where a given waste sample, plastic or even metallic, has to be precisely separated into narrow density fractions to gain data for industrial design or for scientific research. The principle of magnetohydrostatic separators are known even there are industrial size machines but our primary aim was the development of a laboratory-scale separator for analysis of particles of densities up to 6 kg/L and sizes up to 8 mm. Main parts of the built experimental equipment are the ferrite core with two high power coils. The shape of the ferrite core at the two sides of the separator channel was specially designed to produce isodynamic magnetic field. In these places the ferrite core was constructed from laser cut ferrite sheets. The development of the high power electric supply for the two coils was a real challenge because the high voltage and current (400 V, 30 A) and because it had to be precisely regulated for being able to set discrete relative forces on the particles. Two separator channels were made from transparent plastic. The magnetic fluid is circulated by a centrifugal pump, fresh feed is supplied by a vibrated feeder and products can be taken by built in samplers. The velocity profile in the separator channel is measured by an ultrasonic Doppler velocity meter. Paper reports about the development and itself of the magnetohydrostatic separator and about some fundamental and applied laboratory experiments with different reference particles and wastes from used cars and electrical appliances.

Sep 13, 2010

By P Wigley

New methods of analysing and modelling flotation circuits have been developed as part of the AMIRA P9 mineral processing research project. A study using these techniques was conducted on the Olympic Dam copper flotation circuit to provide the following outcomes: an estimate of the flotation cell hydrodynamic properties and froth performance characteristics, and identification of potential areas for improvement; an estimate of the feed floatability parameters for basic model development; and identification of potential flotation circuit improvement opportunities. A flotation circuit model of the Olympic Dam copper concentrator was developed using the data collected from mass balanced site surveys, along with hydrodynamic data, froth performance data and numerous laboratory batch flotation tests. The simulator that has been developed from the model has the ability to estimate the influence of selected changes (such as circuit changes) on flotation circuit performance. Several stream destination simulations were conducted to provide guidance for further testwork and possible circuit improvements. The results from these simulations are presented.

Jan 1, 2003

Maximising margins in today's competitive international commodity markets demands superior productivity. This requires more than simply selecting the best equipment. It requires efficient production and commercial processes together with management systems recognised as international best practice. This paper introduces an integrated way of working that includes management systems for successfully changing work practices and attitudes, developing managers and increasing accountability. It provides an improvement methodology that includes systematic involvement of people in true continuous improvement of processes for maximising productivity and safety while minimising costs. Even though the principles are proven in all industry sectors worldwide, they are not always used correctly. This paper provides examples of traditional performance measurement systems to show how managers miss opportunities to control and improve both production and supporting service processes. It also describes the basic methodology for correct use of the principles and provides examples of correct implementation of modem systems in mining. The charts from actual mining case studies will be elaborated upon in the conference presentation. This paper's main aim is to provide background material for the presentation by introducing integrated principles for building best practice management systems for superior productivity and safety - for higher margins.

Jan 1, 1996

By D Mcleod, S Brindley, S Green

The design and engineering of flotation circuits is driven by numerous inputs, including (in no particular order) testwork outcomes, site considerations, type of separation required, energy sensitivity of the flotation response, personal experience and preference for flotation machines, maintenance access requirements, operability, level of automation and capital constraints.This paper discusses these and other issues in the Australian context and covers the flotation of copper/gold ores and polymetallic (copper/lead/zinc) ores. The paper discusses aspects of the following: how should testwork be done and what are the important inputs and outcomes? how should testwork results be interpreted and how does this impact on equipment selection? what processes can have a critical impact on flotation circuit performance, eg thickening and regrind? what options are available with the typical æflatÆ Australia site? how do you minimise capital cost and what impact can this have on flotation circuit operation and maintenance? how should circuits be controlled and operated? Particular focus is placed on some practical aspects of process design and engineering and the potential impact that engineering decisions can have on flotation plant operation.

Jan 1, 2005