Search Documents

Jan 1, 1931

By G. H. Bruce, C. E. Williams

The trend toward deeper drilling, together with the attcndant increase in power requirements for circulation of the drilling fluid, has emphasized the need for a critical examination of the factors affecting the removal of bit cuttings from the hole by the drilling fluid. The ability of drilling fluids to lift cuttings is called their carrying capacity. A series of laboratory and field experiments has been conducted to determine the minimrim annular velocity necessary to remove cuttings, and to investigate the effects of properties of drilling fluids on their carrying capacities. Consideration of the results of these experiments led to the following conclusions: 1. Turbulent flow in the well annulus is most desirable from the standpoint of cutting removal. 2. Low viscosity and low gel are advantageous in removing cuttings. 3. Increase in mud weight is effective in increasing carrying capacity. 4. The carrying capacity is higher when the pipe is rotated than when it is not. 5. If turbulent flow can be maintained, an annular velocity slightly higher than the slip velocity of the largest cuttings to be transported should keep the bore hole clean. This implies velocities of 100 to 125 ft per minute rather than the presently used 175 to 225 ft per minute. INTRODUCTION Power Savings by Reduction of Annular Velocities A large portion of the power expended in drilling operations is consumed in circulating the drilling fluid. An important factor in establishing the rate of mud circulation is the minimum velocity in the annulus necessary to remove bit cuttings. Empirically, it has been found that average annular mud velocities of about 200 ft per minute will remove cuttings. It was not definitely known, however, whether annular velocities of about 200 ft per minute were just above the minimum necessary to remove cuttings, or whether such velocities could be materially reduced without sacrifice of the ability of the mud to remove cuttings. It is apparent that if annular velocities could be reduced without impairment of cutting removal, a considerable saving in power requirements would result. Need for Research on Carrying Capacity The ability of a drilling fluid to transport cuttings is called its carrying capacity. Although it has been recognized that the carrying capacity of a mud is affected by mud properties such as viscosity and density1,2,3,4 there have been various views in the industry as to the effects of these mud properties on carrying capacity. The economic importance of the problem of carrying capacity and the scarcity of information on the subject indicated that research on the problem was needed. THE FACTORS AFFECTING CARRYING CAPACITY Qualitative Determination of Factors The mechanism of cutting transport is closely related to that involved in the separation of material by settling processes. A considerable amount of research has been done on settling problems, and discussions of sedimentation theory can be found in standard texts.5,6 Consideration of the information available from these sources, together with consideration of the mechanism of cutting transport, leads to the conclusion that the factors affecting carrying capacity are the dimensions of the system, the physical properties of the cuttings. and the physical properties of the drilling fluid. system Dimensions and Their Effect The dimensions of the fluid circulating system of importance to carrying capacity are the bore hole size, drill pipe size, pump capacity, and pump speed. These dimensions determine the annular velocity of the drilling fluid. Physical Properties and Their Effects The physical properties involved in the interaction between mud and cuttings are the density and shape of the cuttings and the density, viscosity and gel strength of the drilling fluid. The effect of the density factor on carrying capacity is fairly obvious; high density difference between cuttings and fluid results in a low buoyant force and therefore decreases carrying capacity. The effect of cutting shape is less obvious. Although

Jan 1, 1951

By C. E. Williams, G. H. Bruce

The trend toward deeper drilling, together with the attcndant increase in power requirements for circulation of the drilling fluid, has emphasized the need for a critical examination of the factors affecting the removal of bit cuttings from the hole by the drilling fluid. The ability of drilling fluids to lift cuttings is called their carrying capacity. A series of laboratory and field experiments has been conducted to determine the minimrim annular velocity necessary to remove cuttings, and to investigate the effects of properties of drilling fluids on their carrying capacities. Consideration of the results of these experiments led to the following conclusions: 1. Turbulent flow in the well annulus is most desirable from the standpoint of cutting removal. 2. Low viscosity and low gel are advantageous in removing cuttings. 3. Increase in mud weight is effective in increasing carrying capacity. 4. The carrying capacity is higher when the pipe is rotated than when it is not. 5. If turbulent flow can be maintained, an annular velocity slightly higher than the slip velocity of the largest cuttings to be transported should keep the bore hole clean. This implies velocities of 100 to 125 ft per minute rather than the presently used 175 to 225 ft per minute. INTRODUCTION Power Savings by Reduction of Annular Velocities A large portion of the power expended in drilling operations is consumed in circulating the drilling fluid. An important factor in establishing the rate of mud circulation is the minimum velocity in the annulus necessary to remove bit cuttings. Empirically, it has been found that average annular mud velocities of about 200 ft per minute will remove cuttings. It was not definitely known, however, whether annular velocities of about 200 ft per minute were just above the minimum necessary to remove cuttings, or whether such velocities could be materially reduced without sacrifice of the ability of the mud to remove cuttings. It is apparent that if annular velocities could be reduced without impairment of cutting removal, a considerable saving in power requirements would result. Need for Research on Carrying Capacity The ability of a drilling fluid to transport cuttings is called its carrying capacity. Although it has been recognized that the carrying capacity of a mud is affected by mud properties such as viscosity and density1,2,3,4 there have been various views in the industry as to the effects of these mud properties on carrying capacity. The economic importance of the problem of carrying capacity and the scarcity of information on the subject indicated that research on the problem was needed. THE FACTORS AFFECTING CARRYING CAPACITY Qualitative Determination of Factors The mechanism of cutting transport is closely related to that involved in the separation of material by settling processes. A considerable amount of research has been done on settling problems, and discussions of sedimentation theory can be found in standard texts.5,6 Consideration of the information available from these sources, together with consideration of the mechanism of cutting transport, leads to the conclusion that the factors affecting carrying capacity are the dimensions of the system, the physical properties of the cuttings. and the physical properties of the drilling fluid. system Dimensions and Their Effect The dimensions of the fluid circulating system of importance to carrying capacity are the bore hole size, drill pipe size, pump capacity, and pump speed. These dimensions determine the annular velocity of the drilling fluid. Physical Properties and Their Effects The physical properties involved in the interaction between mud and cuttings are the density and shape of the cuttings and the density, viscosity and gel strength of the drilling fluid. The effect of the density factor on carrying capacity is fairly obvious; high density difference between cuttings and fluid results in a low buoyant force and therefore decreases carrying capacity. The effect of cutting shape is less obvious. Although

Jan 1, 1951

By H. K. Najarian

This paper describes recent development work on the Wheaton-Najarian Vacuum Condenser for Zinc at Josephtown Zinc Smelter, wherein, to dissipate the heat of condensation, the "airlift" action of gases bubbling through the molten zinc in the condenser is utilized to circulate the zinc through an outside "cooling well" and cooling it continuously. AN earlier paper1 gave an account of initial development of the Wheaton-Najarian Vacuum Zinc Condenser at the Josephtown Zinc Smelter of the author's company. This paper is a progress report of further development work over the years directed toward improving the efficiency and increasing the capacity of the condenser. In this type of zinc condenser, zinc vapor with accompanying noncondensable gases from electro-thermic zinc smelting furnaces is passed upwardly through a mass of molten zinc confined in a refractory-lined U-tube. The zinc vapor condenses in the molten zinc and the noncondensable gases are drawn out of the condenser by suction applied over the surface of the molten zinc. The heat of condensation of zinc, amounting roughly to 1000 Btu per lb of zinc condensed, is absorbed by the molten zinc and, in turn, is dissipated continuously to keep the temperature of molten zinc in a range to permit effective condensation. At the time of publication of our first paper, we had at Josephtown Smelter five units of 69-in.-bore metal furnaces and one larger metal furnace having 96-in. bore. Each 69-in. metal furnace had a condenser with 22-ft overall length. The 96-in.-bore furnace had a condenser with overall length of 31 ft. Condensers were of circular cross section, with corrugated steel outer shell and carborundum lining. Diameter of these condensers was 32 in. inside the refractory lining. Molten metal in the con- denser was kept cool by spraying cold water on the outside of the condenser shell. Under good operating conditions, 22-ft condensers produced some 12 tons of metal per day; and the 31-ft condenser, about 22 tons. When the furnaces produced zinc vapor at higher rates, invariably the condenser temperature would rise to levels where excessive blue powder would form and accumulation of accretions in the condenser would be accelerated. We found that, with the system of cooling in use, we had to provide heat-exchange surface of some 150 sq ft to condense 1000 lb of metal per hr with reasonable efficiency. The wall of the condensers was made up of 5/8-in.-thick corrugated-steel shell having next to it several layers of mica and inner refractory lining of special carborundum shapes to fit the corrugation in the steel shell, and having a minimum thickness of about 2 in. Relatively low rate of heat transfer through the thick condenser wall and slow internal circulation of the molten zinc limited the rate of heat exchange between hot metal within the condenser and the cold water flowing over the outer steel shell. The thickness of the condenser wall was about minimum that we considered suitable for continuous operation. As we learned to operate the electrothermic furnaces with higher power input, producing zinc vapor at higher rates, it became apparent that we needed condensers having larger heat-exchange surfaces. Our 96-in.-bore furnace had 6 single-phase power circuits with transformers rated at 500 kva each and normally good for power input of 3000 kw.

Jan 1, 1959

By R. Fawley, M. A. Quader, R. A. Dodd

Stacking fault energies and annealing twin frequencies have been measured for austenitic stainless steels having a) constant 20 wt pct Cr and varying nickel contents, and b) constant 20 wt pct Ni and varying chromium contents. The effect of nitrogen has also been studied and, to a lesser extent, so has the effect of carbon. All measured stacking fault energies plot linearly against the corresponding annealing twin frequencies, suggesting that, for constant prior deformation and grain size, twinning frequency can be used to estimate stacking fault energy. Compositions low in nickel possess the lowest fault energy, while the maximum fault energy within the investigated composition range occurs mound 20 pct Cr-20 pct Ni. Nitrogen has practically no effect on stacking fault energy when increased from 0.005 to 0.05 wt pct, although Planar dislocation glide is associated with higher nitrogen contents; this may be a short-range order effect. Carbon may raise the stacking fault energy a little, and causes pronounced dislocation tangling in deformed alloys. The basically different dislocation structures promoted by nitrogen and carbon, respectively, are not associated with large variations in stacking fault energy, and the reason for the difference remains unknown. INTEREST in the dislocation configurations developed in plastically deformed alloys arises principally from a desire for an understanding of mechanisms of plastic deformation and fracture. Comparatively little basic work has been concerned with austenitic stainless steels, although considerable interest has developed in the fundamental aspects of deformation of these alloys since the suggestion that those compositions deforming essentially by planar glide are particularly prone to transgranular stress corrosion cracking.' Certain facts are well-established. An 18 Cr-8 Ni steel (type 304) has a low stacking fault energy which is increased by higher nickel contents, and the structure of these steels when moderately plastically deformed changes concomitantly from planar to less planar to distinctly tangled dislocation configurations. These changes are thought to relate to changes in stacking fault energy, and considerable effort has been expended in measuring stacking fault energies of austenitic stainless steels through the determination of node curvatures2"4 even though the method has limitations due to formula approximations,5 an upper limit of measurement of 50 erg cm-2 at the most,5 and the necessity of an extremely meticulous experimental technique. Therefore, it is not surprising that only qualitative agreement between different investigators is generally to be found.'-' At high energies where node radius measurements are inappropriate, some use has been made of annealing twin frequencies to estimate relative stacking fault energies, although a recent critical evaluation of the method suggests that it should be used cautionsly with due regard to effects of grain size and prior deformation.6 Finally, there is a question as to whether the structures of some deformed steels are due to ordering effects. In particular, the role of nitrogen in promoting planar dislocation motion has been suggested to be due to ordering,' but similar suggestions have been made for steels having low interstitial contents.4 EXPERIMENTAL Small ingots of austenitic stainless steels (-50 g) were prepared from components exceeding 99.99 pct purity, the nickel and chromium being Johnson Matthey "Specpure" metals. Carbon was added as pure graphite, and nitrogen as CrN. The components were accurately weighed, and it was assumed that the final composition was the same as the nominal composition

Jan 1, 1969

By H. C. Lukens, E. V. Potter

The volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.² Both sets of data show a minimum solubility between 500' and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. Therefore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. Apparatus and Method The apparatus and method were essentially the same as those described in the previous work,' as shown in Fig. I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transi- . tion points determined under such conditions were less accurate. Absolute Solubility Procedure ad Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1947

By E. V. Potter, H. C. Lukens

The volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.² Both sets of data show a minimum solubility between 500' and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. Therefore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. Apparatus and Method The apparatus and method were essentially the same as those described in the previous work,' as shown in Fig. I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transi- . tion points determined under such conditions were less accurate. Absolute Solubility Procedure ad Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1947

By E. V. Potter, H. C. Lukens

THE volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.2 Both sets of data show a minimum solubility between 500° and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. There- fore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. APPARATUS AND METHOD The apparatus and method were essentially the same as those described in the previous work,1 as shown in Fig, I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transition points determined under such conditions were less accurate. ABSOLUTE SOLUBILITY Procedure and Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1946

By Wilbur I. Duvall, Wilson Blake

The microseismic method of detecting instability in underground mines was developed by the U.S. Bureau of Mines (USBM) in the early 1940's. ,3 The method relies on the fact that as rock is stressed, strain energy is stored in the rock. Accompanying the buildup of strain energy are small-scale displacement adjustments that release small amounts of seismic and acoustic energy. These small-scale disturbances, which can be detected with the aid of special geophysical equipment, are called micro-seisims or self-gene rated rock noises. It was further determined that as failure of rock is approached, the rate at which rock noises are generated increases. Thus, by monitoring a rock structure at intervals and plotting rock noise rates vs. time, a semi quantitative estimate of the behavior and stability of the structure can be made. Since sufficient use of the microseismic method is still being made by various mining and construction companies, USBM undertook a comprehensive review of the method and a study of the fundamental properties of rock noises. As all prior work on rock noises has been done with resonant-type geophones, which prevented any analysis of their vibration records, it was necessary to develop the instrumentation and field techniques in order that their properties could be investigated, such as their frequency spectrum and absorption characteristics, and to determine if both P and S-waves are generated by a rock noise. The aim of this program is the design of microseismic instrumentation which can be better utilized as an engineering tool than the presently available microseismic equipment. This new design, based on the basic properties of rock noises, should allow better utilization of these phenomena in the study and location of zones of incipient instability in both underground and open-pit mines. EXPERIMENTAL PROCEDURE To study the waveform of rock noises, it was necessary to develop a microseismic system with a broad bandwidth. To achieve high sensitivity and broad frequency response, commercial ceramic accelerometers were used. The present broad-band microseismic system consists of accelerometers as geophones, low-noise preamplifiers, high-gain amplifiers, and an FM magnetic tape recorder. This seven-channel system has a flat frequency response from 20 to 10,000 Hz, a noise level of less than 2.0 kv, and a dynamic range (including manual set attenuation) of greater than 100 db; it can detect signals with acceleration levels as low as 2 ug. The entire system is solid state and hence battery operated and portable (Fig. 1) Analysis procedures consist of playing back the 30-in-per-sec (ips) magnetic tape recordings at 1 7/8 ips to expand the time scale of a recorded rock noise event and then recording this on a high-speed direct-writing oscillograph. The oscilIographic records are then digitized and run through Fourier integral analysis computer programs to determine the frequency spectrum of a rock noise event. The oscillographic records are also examined visually to determine if both P and S-waves can be recognized in a rock noise waveform. Broad-band microseismic recordings have been made at field sites in a wide variety of rock types and in both underground and open-pit mines. Sites include the Kimbley Pit, Ruth, Nev.; the Galena Mine, Wallace, Idaho; the Colony Development Mine. Grand Valley, Colo.; the Cliff Shaft Mine, Ishpeming, Mich; and the White Pine Mine, White Pine, Mich. DATA AND DISCUSSION Analyses of the recorded data have shown that rock noise frequencies are very broad. Fig. 2 and 3 show typical rock noise events and their frequency spectrums. In addition, it is evident from these figures that the wave form of a rock noise is very complex. The wide frequency variation, 50 to 7500 Hz, is due to many variables; the effect of travel distance is the only one examined in this study. The higher frequency components of the wave are rapidly absorbed with distance or increasing travel time. Fig. 4 shows the change in waveform resulting from an additional travel distance of 195 ft. From these data, it is apparent that a resonant-type microseismic geophone cannot respond to all frequencies generated by a rock noise, and in spite of the fact that the tuned geophone is more sensitive at resonance, a geophone with less sensitivity but broader band width is much more effective in detecting rock noises. In addition, a study of broad-band microseismic records shows that both P and S-wave arrivals are easily detected, as shown in Fig. 5. All records analyzed to date show that most of the energy is in the S portion of the wave; hence, microseismic geophones should be well

Jan 1, 1970

By Walter Miller

Crude oil stocks were some 10,000,000 bbl higher on June I, 1947, than at any time during 1946 but the extremely heavy refinery runs the last half of 1947 cut crude inventories to approximately the 1946 closing level of 225,000,000 bbl. Many refiners were seriously short of crude oil during the year. This shortage was reflected in numerous advances in the posted price of crude, justified in part as an incentive for more production but more generally due to competitive bidding. Some purchasers of crude, endeavoring to keep their plants running, resorted to the payment, either directly or indirectly, of premiums above the posted price. Another common practice employed by some suppliers of crude oil was to demand refined products in exchange or trade for their raw material. The refined products picture has darkened in spite of record throughputs. Stocks of gasoline and light and heavy fuel oils were uncomfortably low at the beginning of the year and were in general still lower at the close. The rationing of some products, principally gasoline, to dealers and stations? initiated during the year, gained momentum as stocks continued to diminish. The emphasis placed by the manufacturers of oil-burning equipment on the convenience and economy of heating with oil, together with the tight situation in coal, has developed a tremendous demand for burning oils. Consumption of liquefied petroleum gas for domestic and household fuel had more than doubled in 1946 over 1943, and the demand seems to be limited only by the ability of the equipment builders to furnish necessary storage. transportation, and burning equipment. The supply situation is likely to become more acute in 1948. Demand for petroleum products is being pushed to new heights not only by the unprecedented domestic market but by a sudden and drastic upswing in estimates of military and governmental requirements. Additionally, oil exports are running far below the volume requested, amounting to less than forty percent in a recent quarter, and export licenses are reportedly being approved on the basis of urgent need *only. AX recent White House release sees little likelihood that estimated requirements of the sixteen nations participating in the proposed Marshall Plan can be met in full over its projected life—1948 to 1951. Present demand dictates maintenance of refinery operations at the highest possible level and the Bureau of Mines has forecast daily average crude runs in 1948 of 5,265,000 bbl. The Economics Advisory Committee of the Interstate Oil Compact Commission recently estimated the 1948 demand for petroleum products at nearly 6 pct above 1947. They further estimate daily average crude runs of 5,375,000 bbl in 1948, some 2 pct higher than forecast by the Bureau of Mines. Projected demand exceeds supply to the extent that Capitol Hill is reportedly investigating ways of enabling oil companies to act in concert without danger of antitrust prosecution, such as elimination of crosshauls, pooling of products, and lowering of octane.

Jan 1, 1948

By Walter Miller

Crude oil stocks were some 10,000,000 bbl higher on June I, 1947, than at any time during 1946 but the extremely heavy refinery runs the last half of 1947 cut crude inventories to approximately the 1946 closing level of 225,000,000 bbl. Many refiners were seriously short of crude oil during the year. This shortage was reflected in numerous advances in the posted price of crude, justified in part as an incentive for more production but more generally due to competitive bidding. Some purchasers of crude, endeavoring to keep their plants running, resorted to the payment, either directly or indirectly, of premiums above the posted price. Another common practice employed by some suppliers of crude oil was to demand refined products in exchange or trade for their raw material. The refined products picture has darkened in spite of record throughputs. Stocks of gasoline and light and heavy fuel oils were uncomfortably low at the beginning of the year and were in general still lower at the close. The rationing of some products, principally gasoline, to dealers and stations? initiated during the year, gained momentum as stocks continued to diminish. The emphasis placed by the manufacturers of oil-burning equipment on the convenience and economy of heating with oil, together with the tight situation in coal, has developed a tremendous demand for burning oils. Consumption of liquefied petroleum gas for domestic and household fuel had more than doubled in 1946 over 1943, and the demand seems to be limited only by the ability of the equipment builders to furnish necessary storage. transportation, and burning equipment. The supply situation is likely to become more acute in 1948. Demand for petroleum products is being pushed to new heights not only by the unprecedented domestic market but by a sudden and drastic upswing in estimates of military and governmental requirements. Additionally, oil exports are running far below the volume requested, amounting to less than forty percent in a recent quarter, and export licenses are reportedly being approved on the basis of urgent need *only. AX recent White House release sees little likelihood that estimated requirements of the sixteen nations participating in the proposed Marshall Plan can be met in full over its projected life—1948 to 1951. Present demand dictates maintenance of refinery operations at the highest possible level and the Bureau of Mines has forecast daily average crude runs in 1948 of 5,265,000 bbl. The Economics Advisory Committee of the Interstate Oil Compact Commission recently estimated the 1948 demand for petroleum products at nearly 6 pct above 1947. They further estimate daily average crude runs of 5,375,000 bbl in 1948, some 2 pct higher than forecast by the Bureau of Mines. Projected demand exceeds supply to the extent that Capitol Hill is reportedly investigating ways of enabling oil companies to act in concert without danger of antitrust prosecution, such as elimination of crosshauls, pooling of products, and lowering of octane.

Jan 1, 1948

Using 5-p Ni powder and 0.018 ,u A1203, oxide dispersion strengthened nickel alloys were prepared by mechanical mixing of powders, followed by compaction, sintering and extrusion. Processing variables such as cooling of the powder during mixing, electrostatic discharging, mixing time, amount of oxide, and so forth, were studied to determine the effects on room-temperature tensile and high-temperature creep-rupture properties and on the reproducibility of alloys. MECHANICAL mixing of metal and metal oxide powders provides one of the simplest and most inexpensive methods for preparing dispersion strengthened metal-metal oxide alloys;" however, because of large differences in specific gravity, powder particle diameters and other variables, difficulties have been encountered in reproducing alloys and alloy properties. Using 5-p Ni powder and 0.018 p A1203, the following variables were investigated: a) Blending techniques b) Blending time c) Volume fraction of oxide for the selected pow- ders d) Sintering of compacts before extrusion Cooling of Powders During Blending— Cremens and Grant had indicated that dry ball milling of the powder mixture gave superior results over other procedures. When ultra-fine metal and oxide powders became available and comminution was unnecessary or offered little gain, the use of dry mixing in a Waring Blendor gave optimum results.' In the current study, observations of the powder mixtures indicated that considerable heat was generated due to the high speed of the Waring Blendor (15,000 rpm). This heating appeared to produce some degree of clustering and pelletizing. To minimize such agglomeration, a Pyrex cooling coil was installed in the mixing vessel. A double coil, water cooled, proved to be quite satisfactory, providing a fair degree of cooling along with good erosion resistance. Discharge of Electrostatic Charge—Electron-microscopy showed that agglomeration was minimized by the cooling procedure but was not entirely eliminated. It appeared that some of the ag- glomeration had to be explained on the basis of an electrostatic attraction due to the high-speed blending operation. These charges had the effect of promoting the growth of alumina clusters. At the end of the blending procedure such clusters had an effective size which was as much as 50 times that of the individual powder particles and were very tightly bunched. Several methods were utilized to try to discharge the electrostatic forces to minimize the clustering. One successful method, utilized in alloy 17, involved continuous exposure during blending to a radium source of 50 millicuries at a distance of 1.5 ft from the container. A number of other methods were noted to work equally well. Fig. 1 shows the more open oxide structure which results from such a treatment, permitting the matrix metal to penetrate into the cluster more effectively. The combination of powder cooling and discharging led to noticeably improved structures. Fig. 2 shows a cross and a longitudinal section in alloy M-17, one of the best alloys, illustrating the marked decrease

Jan 1, 1961

By C. L. Meyers, A. V. Levy, G. Y. Onoda, R. J. Kotfila

This paper presents the hypothesis that solid-solution hardening of regions in the order of tens of angstroms thick along grain boundaries is the most important mechanism controlling the ductile -brittle transition behavior of poly crystalline bcc refractory metals. Further, a physical model is developed and a general equation is derived to describe the dependence of the solute concentration at grain boundaries on temperature, nominal impurity concentration, thermal treatments, vain size, and prior plastic deformation. Analytical curves of the solute concentration at grain boundaries us temperature, calculated by means of the derived equation, are found to have the same general form as curves of ductility us temperature plotted from experimental data. Senziquantitative relationships between the transition temperature and metallurgical variables can he determined by using the physical model. The room-temperature brittleness of the poly-crystalline refractory metals (tungsten, molybdenum, and chromium) is a result of their high ductile-brittle transition temperatures. Recently studies on single crystals have revealed that, when sufficiently pure, these crystals have much lower transition temperatures than polycrystalline specimens of similar purity.'-3 For example, the transition temperature (measured by reduction in area in tensile tests) for very high-purity tungsten crystals has been reported to be as low as -50°F whereas polycrystalline specimens of similar purity had a transition temperature near 400" ~.' These results suggest that the ductile-brittle transition behavior of these polycrystalline metals can be attributed principally to the influence of grain boundaries on plastic flow and fracture. This paper contains a discussion of the manner in which grain boundaries influence the ductility of the poly-.crystalline bcc refractory metals and proposes that the segregation of impurities to grain boundaries is the most important mechanism for controlling the ductile-brittle transition behavior of these metals. Further, this paper contains an analysis of the effect of the compositional and structural variables on the grain boundary-ductility relationship, and introduces a semiquantitative model that can provide a foundation for more theoretical treatment to describe the influence of these variables on ductile-brittle transition behavior. PHYSICAL MODEL FOR PREDICTING DUCTILE-BRITTLE TRANSITION BEHAVIOR Grain Boundary Segregation of Impurities. Based on their own observations and on theoretical grounds, numerous investigators have suggested that impurities segregate to the grain boundaries. Such segregation would be expected because regions exist where both large and small foreign atoms fit with less strain than within the undistorted crystal structure. Therefore, the concentration of impurities should be higher at boundaries than within the grain body. TO estimate the degree (i.e., the ratio of grain boundary to nominal bulk concentration) to which an interstitial solute tends to segregate at boundaries within a solvent metal, the solubility rather than the size misfit could be used as a guide because solubility expresses the joint effect of both elastic and electronic factors.5 The solubilities of interstitial elements such as carbon, hydrogen, nitrogen, and oxygen are low in the group V-A metals and very low in the group VI-A metals.6 These low solubilities suggest that segregation to grain boundaries should occur for each of these solutes in both refractory metal groups. The difference between the ductility of single-crystal and polycrystalline bcc refractory metals can be described in terms of two distinct effects.4 The first of these is the general observation that grain boundaries hinder slip within grains and slip transfer between grains, and the second is that deformation is more complex in each grain of a polycrystalline specimen than it is in a single crystal. Mc Lean has pointed out, furthermore, that strong slip-hindrance effects at grain boundaries should occur in metals having strong segregation of impurities to grain boundaries. Therefore, the effect of grain boundaries on the hindrance of slip is expected to be the dominating influence on the ductile-brittle transition behavior of these polycrystalline refractory metals. cahn5 has suggested that temperature and solute mobility should influence solute equilibrium segregation at grain boundaries, and Fig. 1 illustrates

Jan 1, 1965

By Philip Morse

THE Australian lead-smelting plants began to use charges carrying high zinc percentages somewhat earlier than was common with American plants. When lead smelting first started in Australia the immense deposits of oxidized lead at Broken Hill were available but later these oxidized ores became exhausted and were replaced by sulfides. This was before the days of flotation and these sulfides when concentrated carried about 1 per cent. of zinc to 6 per cent. of lead. The works of the Sulphide Corpn. at Cockle Creek was perhaps the pioneer in high-zinc slags but the Port Pirie plant of the Proprietary Co. was a close and very able second and has continued the work to the present time. The Cockle Creek lead furnaces remained in operation until shortly after the war when most of the Broken Hill companies combined and took over the Port Pirie plant to treat their concentrates. As it was the practice both at Cockle Creek and Port Pirie to carry 20 per cent. or more of lead on the charge, it was found that under these conditions of large amounts of zinc in the charge, good roasting was absolutely necessary and matte production was unwise. The Huntington-Heberlein system of roasting was introduced and later the Dwight & Lloyd process. In this way, by roasting the sulfide portions of the charge as thoroughly as possible and making no matte, a method of smelting was developed where the slag over long periods carried as high as 20 per cent. ZnO without serious furnace troubles, and slags carrying even up to 33 per cent. ZnO have been reported. The zinc slags were not very different in appearance from the ordinary slags produced in American practice except that they gave off more smoke and fume on tapping. The slag usually ran hot and freely, coming from the tap in a full stream. Normally there was little crust on the sides' of the furnace and the tuyeres gave no trouble though they were always rather dark.

Jan 1, 1929

By F. A. Crossley

The key to disagreements between Blackburn's findings and mine is the word equilibrium". My work attempted to define the equilibrium diagram of the titanium-rich end of the Ti-A1 system. It can readily be shown that Blackburn's conclusions are based primarily on the examination of structures substantially removed from equilibrium. The diagram presented in Fig. 16 is properly labeled a "phase diagram". However, it appears that Blackburn either does not understand or does not accept the difference between "phase diagram" and "equilibrium diagram" as defined in the Metals Handbook.17 The conflict lies not in Blackburn's data but in his interpretation of it, and his use of "transformation", "phase diagram", and "equilibrium diagram" as synonymous terms. I share his view that the light microscope is much inferior to the transmission electron microscope for the study of transformations; but this fact does not render the light microscope useless or untrustworthy. The difficulties experienced with the Ti-A1 system have not been due to the limitations of the light microscope, but rather to the extreme sluggishness in achieving equilibrium at temperatures below 1000° C. Were it not for the light microscope employed with polarized light, the twin phase syndrome' might still be unrecognized and, as a consequence, still adding to the confusion of Ti-A1 investigations. (Ref. 1 should read ... Contract No. N161-25952 ... vol. 236.) Other, more sophisticated techniques, including electron transmission, simply confirm the erroneous tentative conclusions drawn from observations of structures due to the twin-phase syndrome. By the standards of most of the investigations of the Ti-A1 systems, seven of the fifteen compositions investigated by Blackburn were seriously contaminated with oxygen. The writer has found that 0.1 wt pct 0 shifts the a + Ti3A1 boundary to 1 at. pct lower A1 content at 700°C. At constant aluminum content, this corresponds to a temperature shift of the boundary of +25°c.18 Blackburn advises that the first group of alloys contained 0.1 to 0.15 wt pct 0, bur he does say whether the analyses were performed on as-received material or on specimens in their final state of heat treatment. This is especially important considering the 20-mil-thick starting materials. If specimens had been annealed in the two-phase a + 6 region it would have provided an indication of the final degree of oxygen contamination since up to about 12 at. pct A1 the boundaries of this region are well-defined for low-oxygen alloys. Blackburn questions the capability of light microscopy in determining phase boundaries in the Ti-A1 system. I submit that the a/a + Ti3A1 boundary in Fig. 1 of Ref. 1 over the composition range from 10 to 18 at. pct A1 was determined by dilatometry and supported by electron diffraction. Specimens of alloys containing 8, 10, 12, and 14 at. pct A1 were aged at 550°C for 1000 hr (under stress of 5000 psi to accelerate the tendency to equilibrium) and then fractured in tension at room temperature. Collodion was applied to the as-fractured (unetched) surface and, when stripped, carried away particles identified by electron diffraction as Ti3A1. Perhaps Blackburn will explain why these electron diffraction data were ignored. At this time, a technique for revealing or indicating

Jan 1, 1969

By Milton F. Goodrich

The idea of using water-only cyclones to scalp clean coal from the feed to other devices has recently been gaining in popularity. 1,2,6 An indication of this popularity is that water-only cyclone scalping is already employed in a few commercial plants. Water-only cyclones scalp the feed to a heavy media vessel in the Warwick plant,3 to Deister tables in the Rowland plant,4 and to a heavy media cyclone circuit in the Amherst Coal Company's McGregor plant.5 Despite this trend, we found surprisingly little information in the literature on the performance of water-only cyclone scalping. Therefore, we undertook a study of its technical merits, limiting our investigation to a water-only cyclone scalper in conjunction with heavy-media cyclones. We felt this to be a reasonable combination of equipment, since both processes operate well on the same size coal. First, we developed simple mathematical relationships revealing general characteristics of the system. Next, we compared the clean coal yield and quality obtainable by the system on four different coals with that obtainable by heavymedia cyclone circuit alone and water-only cyclones middlings recirculation circuit alone. This was done by using computer program to simulate the operation of the three systems. Finally, we considered the effect that implementation of the system would have on a typical preparation plant circuit. The System The system chosen for study [(shown schematically in Fig. 1)] comprises two stages: a primary stage (PI) consisting of water-only cyclones, and a secondary stage (P2) consisting of heavy media cyclones. The water-only cyclones separate raw coal at a low specific gravity, producing a relatively small amount of high quality clean coal and a refuse containing much good coal. This refuse is then recleaned in the secondary stage, where the sharper separation of heavy media cyclones, operated at a higher specific gravity, reclaims additional clean coal. Finally, the clean coal from both stages is combined as the system's clean coal, while the refuse from the secondary stage becomes the system's refuse output. Theoretical Analysis Two assumptions lie behind the following theoretical analysis. The first assumption is that partition curves can represent not only the performance of each stage but also the performance of the system as a whole. These curves show partition number as a function of specific gravity, where partition number is either the percent or fraction of a raw coal with a given specific gravity reporting to clean coal. The second assumption is that these curves are independent of the raw coal characteristics. At any specific gravity the system's partition number is solely a function of the partition numbers of each stage. For convenience, we use the following variables in describing this relationship: g = specific gravity, PS(g) = the partition number of the system at specific gravity g, P1(g) = the partition number of the primary stage at specific gravity g, P2(g) = the partition number of the secondary stage at a specific gravity g. For this system, we can show algebraically that the relationship is: [Ps (g) = PI (g) + (1- P1(g)) P2 (9)(1)] With this equation the system's partition curve can be determined if the partition curves of each stage are known. By definition, the partition numbers P1(g) and P2(g) must each be less than, or equal to, one. Placing these constraints on Eq. (1), we arrive at the relations: [Ps(g) % P1(g) and Ps(g) % P2(g)(2)] Thus, at any specific gravity the system's partition number is always greater than that of both stages. [Figure 2] shows typical partition curves. Curve I represents the primary stage, which consists of water-only cyclones operating at a separating gravity of 1.3. (The separating gravity or the

Jan 1, 1979

By F. R. Scauzillo

Equilibrium data which should be useful in the design and/or evaluation of glycol dehydration units were prepared from an analysis of various published data and the correlation of these data by the use of the thermo-dynamic equilibrium ratio. The equilibrium ratios of water are used to solve the glycol absorber problem; such solutions are necessary to define the number of trays and the glycol circulation rate needed to meet drying requirements. Activity coefficients were obtained which relate directly to the equilibrium ratios of water in the water-TEG-natural gas system. These activity coefficients have been used to calculate the equilibrium dew points for aqueous TEG concentrations of 60 to 99.9 weight per cent for the temperature range of 40° to 120° F. They also provide a means of calculating equilibrium ratios for water in the water-TEG-natural gas system; this applies to any desired TEG concentration and to the temperature range from 40° to 120°F. INTRODUCTION During the last several years, the drying of natural gas with aqueous triethylene-glycol (TEG) solutions has become very prominent. Most users of TEG as a drying agent have been satisfied with the performance of TEG solutions at the conditions used; however, there always has been some discussion of the drying ability of TEG solutions at conditions not commonly encountered such as temperatures below 50° or 60°F, but more particularly temperatures above 100°F, and pressures above 1,000 psia. Today, when higher wellhead temperatures such as 120°F are more commonly encountered many are skeptical of TEG's ability to dry sufficiently well to provide dew points around 32°F, which is generally the maximum tolerable when attempting to dry a gas to contract specifications of 7 Ib/MMscf. These views probably have evolved to some extent from the days when suppliers would not guarantee dew-point depressions in excess of 65° to 75 °OF. Also, the feelings about TEG drying may have arisen from the lack of information about the equilibrium relation of water in the drying operations. Porter and Reid' have reported equilibrium data for a 95 per cent TEG solution, while Townsend2 reported equilibrium data for 95, 98 and 100 per cent TEG solutions. Townsend also presented a calculational method which obtains activity coefficients in the liquid phase and, subsequently, the equilibrium water content of a saturated gas over glycol from published3 atmospheric dew points. Wise, Puck and Failey' presented activity data for the water-TEG system at atmospheric pressure. In the past, the equilibrium ratios published for water in a 95 per cent by weight aqueous TEG solution have been used indiscriminately by many for all concentrations of TEG encountered in gas drying operations. Since essentially all such gas operations require the use of more concentrated TEG solutions, a study was undertaken to correlate the existing equilibrium data for aqueous TEG and gas systems and to provide some means of calculating the equilibrium ratio of water in the natural gas-water-TEG system where TEG concentrations were other than 95 per cent. The data presented herein consider only the equilibrium drying ability of the TEG solutions and do not consider the effect of temperature and pressure on the tray eficiency of contactors. In other words, this paper is concerned primarily with the development of the equilibrium relationship between water in the dried natural gas and the water in the lean TEG entering the top tray of the absorber. BASIC EQUILIBRIUM RELATIONS A relationship which relates the K value of water in the natural gas-water-TEG system to the vapor pressure of water at the system temperature, the total pressure of the system and the activities of the liquid and gas phases has been evaluated. It is well known that, for any component of a mixture at equilibrium between a gas phase and a liquid phase,

By P. A. Flinn

ALTHOUGH many physical properties of superlat-tices have been studied intensively, relatively little attention has been paid to their mechanical properties until recently. Even for the well-known transformation in 0 brass, the effect of the transformation on plastic behavior has only lately been extensively investigated.''' A partial analysis of dislocation structure in superlattices has been given by cottrel13 and his theory agrees well with the experimental results on CU3AU.4,5 His analysis, however, is implicitly limited to low-temperature effects, since it does not include the behavior of dislocations at temperatures high enough for diffusion, and hence climb, to occur. The work of Herman and Brown2 on the creep of 0 brass indicates that important effects occur under such conditions, and consequently, the theory should be extended to include them. Such high-temperature effects cannot be observed in Cu3Au, since it disorders below the temperature at which diffusion occurs at a reasonable rate. There are materials of the same structure, however, such as Ni3A1, which retain their order up to, or close to, the melting point. GEOMETRY OF THE COMMON SUPERLATTICES The two best-known ordered structures are the 0 brass type, B2, shown in Fig. 1, and the Cu3Au type, Ll2, shown in Fig. 2. In the B2 structure the (000) and (1/2, 1/2, 1/2) sites are different in that they are occupied by different types of atoms. The symmetry of the structure is then lowered from a body-centered cubic, A2, in which the sites are equivalent, with atoms located randomly in the sites, to simple cubic. This lowering of symmetry has the consequence that two types of regions may occur within a crystal: regions where A atoms are in the (0, 0, 0) sites, and regions where they are in (1/2, 1/2, 1/2) sites. The boundary between two such regions will contain bonds between like atoms, and be a surface of higher energy. These regions are known as antiphase domains and the boundary as antiphase boundary. In the B2 structure, boundary formed during the ordering process should disappear as a result of domain growth, since any domain growing to the boundary of two others will join one and engulf the other.' In any well annealed crystal, only a single domain should exist, with antiphase boundary present only in connection with dislocations, as discussed below. The L1, structure is related to the A1 (face-centered cubic) in much the same way as the B2 is to the A2. The face-center sites are occupied by A atoms, and the corner sites by B atoms. The symmetry is again lowered to simple cubic, and antiphase domains can exist. In this case, however, there are four initially equivalent sites in the unit cell: (0,0,0), (0, 1/2, 1/2), (1/2,0, 1/2) and (1/2, 1/2, 0). In the ordered structure any one may be occupied by a B atom and the other three by A atoms. Thus four types of antiphase domains can occur in this structure. This is sufficient to permit a metastable "foam structure" to exist within a crystal.''7 Antiphase boundaries along three different planes are shown in Figs. 3, 4, and 5.* *The presence of a layer of disordered material between antiphase domains, as suggested by Jones and Sykes8 does not seem likely. Such a layer would be a region of unnecessarily high energy which could readily be reduced by the formation of the type of boundary discussed here.__________________________________________________________ The notation (111) [110] means a boundary lying along a (111) plane between antiphase regions related by a 1/2 [I10] translation. It may be seen in Figs. 3 and 4 that an antiphase boundary usually results in incorrect nearest neighbors (shown connected by braces). However, as pointed out by Wilson, a boundary of the (001) [I101 type can exist

Jan 1, 1961

By R. W. Raymond

Franklin Guiterman was born March 7, 1856, in Cincinnati, Ohio, where his father, William Guiterman, was at that time engagcd in the wholesale dry-goods business. Both of his parents were natives of Bavaria, but the inspiration of America was upon them, as they gave to their son a peculiarly American name, symbolizing thrift, individualism and scientific knowledge. Franklin Guiterman received his general education in the grammar schools and the Hughes High School of Cincinnati. He finished the latter course in the early 70's of the last century, when the great demand for mining and metallurgical experts in this country naturally led his parents to direct his further studies in that direction. Accordingly, he went to Europe, and studied at the Royal Saxon Mining Academy of Freiberg, where he completed the course in 1877, at the age of 21, and returned to the United States to engage in mining and metallurgical practice. Going to Colorado, he became assayer for the Terrible mine, at Georgetown, and in 1878, for the Little Chief mine at Leadville. The position of assayer, particularly at that period and in that region, was the door to much valuable knowledge of mines and ores. Besides learning the nature and value of the different classes of ore from the mines of his own company (if he was employed by a company) the assayer, had the first chance, through his outside customers, of seeing and testing the specimens brought by prospectors, and thus learning of important new discoveries. Moreover, if he possessed metallurgical knowledge, he might advance to the position of a metallurgical manager. Guiterman stayed in Leadville four years, and during that period was assayer or chemist for several different companies. Then for about a year he superintended copper-mining operations at Hartville, Wyo. In 1884, he had charge of sampling works at Silverton, colo.—an admirable opportunity for gaining wide knowledge of the varied ores of the San Juan country. In 1885, he was Superintendent of the Mingo plant of the Pennsylvania Lead Co., at Sandy, near Salt Lake City, Utah. The foregoing list of employments, each occupying not more than a year, certainly looks like the history of a rolling stone, gathering no moss. But the cause of these frequent changes was not inefficiency in each new position. In that time and period, a man who lost his place for such a reason was not likely to get another in the same neighborhood might away. And as for gathering "moss," the kind of "moss" that

Jan 1, 1918

By P. T. Bail, J. E. Bobek

In reservoirs containing soft shales interbedded with oil-producing sands, it is possible to have water movement from the shales into the sands during reservoir depletion. This paper presents the results of scaled flow-model tests performed to investigate the efficiency of oil displacement by this vertical influx of water into oil-producing sands. In these model tests, the effects of rate of influx and rock wettability were considered. Oil recoveries by shale-wafer influx and by water flooding were cornpared after 0.4 hydrocarbon volume of water entered the producing sand. This comparison was made for water-wet and oil-wet systems. In water-wet sand, shale-water influx produces slightly less oil than conventional water flooding; in oil-wet sand, shale-water influx produces about one-half as much oil as conventional water flooding. In another type of comparison, it was found that shale-water influx followed by water flooding recovers less oil than water flooding alone. This is true for both water-wet and oil-wet sands. A comparison of tests run at different rates of shale-water influx shows that oil recovery is insensitive to rate in water-wet sand; in oil-wet sand, oil recovery decreases with decreasing rate of influx. INTRODUCTION Localized subsidence of the earth's surface has accompanied the depletion of some oil reservoirs, particularly in California,1, 2 along the Texas Gulf Coast,3 4 and in the Bolivar Coastal fields of Venezuela. Subsidence occurs when fluid withdrawals reduce the pressure in the reservoir. The reasons for subsidence accompanying a reduction in reservoir pressure are not known with certainty.10° However, there is considerable evidence that compaction of soft shale beds adjacent to producing oil sands can be a major cause of this subsi-dence.3, 6, 10-12 When the shales compact, a limited amount of water moves from the shales into the producing sands. A schematic illustration of this oil-producing mechanism is shown in Fig. 1. As the pressure in the sand declines due to oil production, a predominantly vertical pressure gradient develops at the sand-shale boundary. This causes water to move from the shale into the sand as indicated by the solid arrows. This paper reports the results of scaled flow-model tests to investigate the efficiency of oil displacement by the vertical influx of shale water into producing sands. The model tests were not performed with the aim of duplicating the recovery behavior of any specific reservoir. The primary purpose of the tests was to obtain a better understanding of oil displacement by shale-water influx. A knowledge of the oil- and water-production characteristics of even a simplified reservoir system should be of value to engineers estimating the performance of reservoirs where shale-water influx is occurring in conjunction with other production mechanisms. The following limitations and assumptions apply to the model work. 1. The sand of the prototype reservoir is homogeneous and horizontal. 2. The shale-water influx is uniformly distributed along the top and bottom of the sand member being studied. 3. No effects of edge-water drive or dissolved-gas drive that might accompany shale-water influx are considered. PROTOTYPE RESERVOIRS Scaled-model tests were performed to study oil displacement from three prototype reservoir sections. The reservoir sections modeled consist of single sand layers out of a sequence of -sand and -shale layers, as illustrated in Fig. 1. Each prototype represents a homogeneous, high-permeability, unconsolidated sand layer. In the field, the prototype is oriented in such a manner that one end is at the radius of drainage of a producing well and the other end is pointed toward the producing well (Fig. 2). The sand and fluid properties and the dimensions of the three prototypes are given in Table 1. The capillary pressure relationships for the three prototypes are presented in Figs. 3, 4 and 5. The oil-water per-