Search Documents

Page Foreword. By Edmund M. Wise..................... 3 A.I.M.E. Officers and Dircctors...................... 4 Institute of Metals Division Officers and Committees............ 7 Institute of Metals Division Annual Award Certificate............ 8 Institute of Metals Division Lectures and Lecturers............. 9 Photograph of E. H. Dix, Jr., Institute of Metals Division Lecturer...... 10 PAPERS Acceleration of the Rate of Corrosion by High Constant Stresses. By E. H. Dm, JR. (Institute of Metals Division Lecture, T. P. 1204).......... 11 Variation of Internal Friction with Grain Size. By Clarence Zener and R. H. Randall. (T.P. 1146, with discussion) .............41 Changes in Damping Capacity during Annealing of Alpha Brass. By John T. NoRton. (T.P. 1168, with discussion)................49 An Electron Diffraction Study of Anodic Films. By R. A. HarrinQton and H. R. Nelson. (T.P. 1158).....................62 Determination of Orientations by Etch Pits. By Charles S. Barrett .and L. H. Levenson. (T.P. 1171, with discussion).............76 Process of Precipitation from Solid Solution, I—A Crystallographic Mechanism for the Aluminum-copper Alloys. By Carl H. Samans. (T.P. 1186). . . 85 Age-hardening of Aluminum Alloys, IV — Discussion of the Theory. By WilTJam L. Fink and Dana W. Smith. (T.P. 1083, with discussion). . . 95 Structure of Aluminum after Compression. By Charles S. BaRREtt and L. H. evensonON. (T.P. 1104, with discussion)................112 Recrystallization Texture of Aluminum after Compression. By ChaRlEs S. BarRett. (T.P. 1141, with discussion)................128 Plastic Deformation and Recrystallization of Aluminum Single Crystals. By J. A. Collins and C. H. Mathewson. (T.P. 1145, with discussion) . . . 150 Recovery and Recrystailization in Long-time Annealing of 70-30 Brass. By S. E. Maddigan and A. I. Blank. . (T.P, 1166, with disonssion).....170 Correlation of Deformation and Recrystallization Textures of Rolled 70-30 Brass. By R. M. Brick. (T.P. 1144, with discussion).........193 Tensile Deformation of Critically Oriented Brass Crystals. By H. L. Burghoff. (T.P. 1149).............................214 Recrystallization of Lead. By Paul A. Beck. (T.P. 1101, with discussion). . 222 Simple Method of Thermal Analysis Permitting Quantitative Measurements of Specific and Latent Heats. By Cyril Stanley Smith. (T.P. 1100, with discussion).............................236 Metallographic Study of Internal Oxidation in the Alpha Solid Solutions of Copper. By Frederick N. Rhines. (T.P. 1162, with discussion). . . . 246

Jan 1, 1940

Page Foreword. By Edmund M. Wise..................... 3 A.I.M.E. Officers and Dircctors...................... 4 Institute of Metals Division Officers and Committees............ 7 Institute of Metals Division Annual Award Certificate............ 8 Institute of Metals Division Lectures and Lecturers............. 9 Photograph of E. H. Dix, Jr., Institute of Metals Division Lecturer...... 10 PAPERS Acceleration of the Rate of Corrosion by High Constant Stresses. By E. H. Dm, JR. (Institute of Metals Division Lecture, T. P. 1204).......... 11 Variation of Internal Friction with Grain Size. By Clarence Zener and R. H. Randall. (T.P. 1146, with discussion) .............41 Changes in Damping Capacity during Annealing of Alpha Brass. By John T. NoRton. (T.P. 1168, with discussion)................49 An Electron Diffraction Study of Anodic Films. By R. A. HarrinQton and H. R. Nelson. (T.P. 1158).....................62 Determination of Orientations by Etch Pits. By Charles S. Barrett .and L. H. Levenson. (T.P. 1171, with discussion).............76 Process of Precipitation from Solid Solution, I—A Crystallographic Mechanism for the Aluminum-copper Alloys. By Carl H. Samans. (T.P. 1186). . . 85 Age-hardening of Aluminum Alloys, IV — Discussion of the Theory. By WilTJam L. Fink and Dana W. Smith. (T.P. 1083, with discussion). . . 95 Structure of Aluminum after Compression. By Charles S. BaRREtt and L. H. evensonON. (T.P. 1104, with discussion)................112 Recrystallization Texture of Aluminum after Compression. By ChaRlEs S. BarRett. (T.P. 1141, with discussion)................128 Plastic Deformation and Recrystallization of Aluminum Single Crystals. By J. A. Collins and C. H. Mathewson. (T.P. 1145, with discussion) . . . 150 Recovery and Recrystailization in Long-time Annealing of 70-30 Brass. By S. E. Maddigan and A. I. Blank. . (T.P, 1166, with disonssion).....170 Correlation of Deformation and Recrystallization Textures of Rolled 70-30 Brass. By R. M. Brick. (T.P. 1144, with discussion).........193 Tensile Deformation of Critically Oriented Brass Crystals. By H. L. Burghoff. (T.P. 1149).............................214 Recrystallization of Lead. By Paul A. Beck. (T.P. 1101, with discussion). . 222 Simple Method of Thermal Analysis Permitting Quantitative Measurements of Specific and Latent Heats. By Cyril Stanley Smith. (T.P. 1100, with discussion).............................236 Metallographic Study of Internal Oxidation in the Alpha Solid Solutions of Copper. By Frederick N. Rhines. (T.P. 1162, with discussion). . . . 246

Jan 1, 1940

By Leonard Larson

Before direct or wet smelting of copper concentrate was adopted at the McGill smelter, in November 1932, actual furnace smelting tests had indicated the possibility of smelting between 400 and 500 dry tons of wet concentrate per furnace day. Under calcine smelting practice, solid charge up to 116; tons per furnace day had been smelted. It was realized that in order to smelt wet tonnage in equivalent amount per furnace day, a higher combustion rate and higher temperatures would be necessary within the furnace. The reverberatory furnace considered in the following history of wet-smelting developments is a unit rz7 ft. long and 28 ft. 8 in. wide, inside dimensions (Fig. I). This furnace was in operation through all the years from 1934 to date. During 1933, the first complete year of direct or wet smelting, the plant was on a curtailed copper-production basis and the available concentrate tonnage to be smelted was limited. The average coal-firing rate in the reverberatory for that year was 124 tons per furnace day. This rate was lower than the average for years immediately preceding under calcine smelting practice. With this coal-firing rate, an average of 391 tons of new metal-bearing material (N.M.B.M.) was smelted per furnace day. The following year, 1934, the coal-firing rate was increased to 139 tons and the smelting rate increased to 448 tons N.M.B.M. per fur- nace day. In succeeding years production required that either more tonnage be smelted in the one furnace or an additional furnace be placed in operation. With this situation confronting the smelting department, it was determined to continue the program of increasing the coal-firing rate and also to intensify the temperature in the smelting zone of the furnace. In order to accoinplish this, various improvements were made to aid combustion within the furnace. The burners were enlarged, increased primary air was supplied to the burners, and changes were made in the furnace to enlarge and streamline the outlet, thus increasing the furnace draft. The coal-firing rate was increased yearly until 1937 when the firing rate averaged 210 tons per furnace day. Thereafter the firing rate fluctuated according to character of charge and production requirements. In general, however, with the same character of charge the smelting rate increased in almost direct proportion to the increases in firing rate. Table I shows the average coal-firing rate, smelting rate, and other pertinent data for the direct-smelting years of 1933 to 1939 inclusive, the first fivc months of 1940 and May 1940. These figures show that the water evaporated in the waste-heat boilers was in almost direct proportion to the coal-firing rate. In making comparisons in the table, it should be borne in mind that the figures, except for May 1940, are yearly averages. Because of changes in character of charge or operating conditions, records for individual days or even months

Jan 1, 1944

By F. S. McNicholas, M. S. Walker, V. C. Rogers

During the year of 1944 and the first half of 1945, the Climax Molybdenum Co. made a study of some of the problems in block and panel caving, with the use of a scale model. The experiments dealt essentially with the type of rock and conditions at Climax, but some experiments were carried out to simulate conditions found in other mines. Most of the previous experiments on the caving characteristics of rock have dealt with sedimentary or broken igneous material. The series of experiments described here was designed to show the caving action of unbroken igneous rock. Con- siderable difficulty was experienced in duplicating unbroken material in the model. The results obtained are believed to be relatively correct, but verification must necessarily come from future mine operation. Observations in the mine and glory hole, together with statistical data, were used as criteria for creating similar conditions in the model. In 1913, George R. Lehman' experimented with broken material in a model for the Inspiration Consolidated Copper Co. and, more recently, P. B. Bucky2 experimented with broken material with a capping of mill tailings. Mr. Lehman's model represented a maximum ore height of 70 ft. capped by 55 ft. of waste. He varied the draw-hole spacing from 6¼ ft. to 8? ft. and 12½ ft. The material used graduated from fines to 30-in. maximum size. Some of his conclusions were: "(I) The less the distance between chute centers, the greater the extraction (Fig. I); (2) the higher the ore column, the greater the extraction; (3) the less the amount drawn at a time from each chute, uniformly, the greater the extraction of clean ore before the capping appeared, but not the greater the total extraction to a I per cent copper final product." (Fig. 2.) Professor Bucky concluded, in part: "(I) Drawing of ore may take place at any time from any finger and in any amount without affecting materially: (a)

Jan 1, 1946

By L. L. Handy

Solvent floods using slugs of solvent have been found to show continuity in behavior from the vapor pressure of the solvent to the critical pressure for the two-component driving gas-solvent system. In the pressure region between the solvent vapor pressure and the critical pressure for the gas-solvent system, the gar and solvent are only partially miscible. Although complete miscibility cannot be obtained at these pressures, complete oil recovery is possible in principle. In two-phase solvent floods the solvent is propagated tllrough the reservoir, primarily, in the vapor phase. The carrier gas requirements constitute a significant factor in the economics of the process. A qualitative theory is proposed for estimating the amount of dry gas required to move the solvent through the reservoir. The theory shows that for two-phase solvent floods the total gas needed is a minimum at the vapor pressure of the solvent and at the critical pressure for the gas-solvent system, and is a maximum at some intermediate pressure. The predictions of the theory are supported by experimental studies using methane, butane and decane or methane, propane and decane in a natural sandstone core. INTRODUCTION Previously, solvent slug processes have been found effective for oil recovery in two pressure ranges. First, conventional miscible displacements are possible at pressures greater than the critical pressure for the gas-solvent system. Second, Jenks, et al,' have shown that, at pressures slightly in excess of the vapor pressure of the solvent, a solvent slug can be propagated through a reservoir by a gas essentially insoluble in the liquid solvent. The solvent bank displaces the oil ahead of it. Both of these processes, at least ideally, are capable of recovering all of the oil in the swept regions. Slug processes for which the gas and solvent are partially miscible have not been considered; that is, those systems for which the solvent and driving gas form two equilibrium phases in which the vapor phase contains a significant amount of solvent and the liquid phase an appreciable amount of the driving gas. Welge and Johnson' have shown that the gas needed to movc a solvent slug through the reservoir increases with increasing pressure above the vapor pressure of the solvent. It will be shown that solvent slug processes can, theoretically, recover all of the oil at any pressure greater than the vapor pressure of the solvent. But the amount of gas required to move the solvent through the reservoir depends very much on the pressure and temperature. In the present study a maximum in the gas requirements was both predicted theoretically and observed experimentally. This result has not been reported previously, and would not have been predicted from the Welge and Johnson model. The gas requirements are a minimum at the pressures corresponding to the vapor pressure of the solvent and again at the critical pressure for the gas-solvent system, and are a maximum at some intermediate pressure. AN APPROXIMATE THEORY FOR TWO-PHASE SOLVENT FLOODING The differences and similarities between conventional solvent floods and two-phase solvent floods are best understood by referring to concepts developed for miscible displacement in which miscibility is generated in the reservoir. In Fig. 1(A), a ternary diagram is shown for a hypothetical gas-solvent-oil system. To be rigorous the three components should each consist of a single molecular species. The pressure for Fig. 1(A) is greater than the critical pressure for the binary gas-solvent system at the specified temperature. Diagrams of this type are the ones most frequently referred to in discussions of enriched-gas drive and miscible displacement. A limiting tie line is shown tangent to the two-phase envelope and intersecting the gas-solvent line at Point A. To obtain generated miscibility with this type system, others have shown that, for an oil of Composition D, a mixture of gas and solvent must be injected which is richer in solvent than that composition indicated by A. An oil repeatedly contacted with a gas phase richer than A changes toward a composition which would be at equilibrium with the injected mixture, that is, a composition lying on a tie line which passes through the injected-gas composition. Since no such tie line exists, the oil is enriched to the point at which it becomes directly miscible with the injected mixture. At pressures lower than the critical pressure for the gas-solvent system, other types of phase diagrams are observed. The ones of interest in this paper are for pressures greater than the vapor pressure of the solvent, but less than the critical pressure of the gas-solvent system. Such a ternary diagram is shown on Fig. 1(B). In this case, two-phase behavior is observed not only for gas-oil mixtures, but also for certain compositions in the gas-solvent system. If a gas of Composition A (a dew-point vapor) is injected, once again the original oil is enriched by successive

By C. A. Fothergill

An improved blotter model is described which makes use of a plastic sheet as base for the blotter field and pins to represent the input wells. The model is simple to construct and adapt and is particularly useful for demonstration purposes. Operational details are given. INTRODUCTION The blotter model was first applied to the investigation of oilfield problems by Wyckoff, Botset and Mus-kat,' primarily in order to demonstrate the flood patterns which could be expected from various arrangements of input and output wells in waterflooding projects. In recent years the model has been largely superseded for analog studies by the potentiometric and electric analog models which are more refined and versatile, since they can simulate the form, and, in certain cases, permeability variations which it is not possible to do with the blotter model. However, the latter is still used for analog studies where the reservoir can be represented as being uniform in thickness and permeability, and where a visual record of the flood advance is required. Ramey andNabor,2 for example, have applied the model to the investigation of areal sweeps in oil recovery by in-situ combustion. Because of its limitations, the blotter model can be used in general for only very simple arrangements of input and output wells, but within these limitations it has a definite advantage over all other types, in that it provides a picture of the advancing flood using the simplest and most easily constructed apparatus, by contrast with the gelatin model, for example, which requires more elaborate equipment. Moreover, the experiments can be quickly repeated and modified if necessary, whereas considerable time is required to prepare a gel field, compared with that required for the preparation of sheets of conducting blotting paper. For these reasons the blotter model can be very useful for demonstration and teaching purposes, enabling the student to experiment for himself with different arrangements of input and output wells. A model has been constructed for this purpose which is simple to operate and adapt. The model (Fig. 1) consists of a base platform or box, approximately 12-in. square, on top of which are screwed three lathes of 1/2 -in. square section to form three sides of a square 6 in. in length. This forms the support for a sheet of Cobex, transparent plastic, thickness .003 in., on which is carried the blotting paper representing the field. The plastic is flexible and relatively soft, and can be attached to the support by cellulose tape so that it can be easily removed when required. The input wells are represented by brass drawing pins pressed through the plastic sheet from the underside until the points are just projecting through the top; these are connected in the circuit as shown in Fig. 2. The sheet of blotting paper of required shape and size is saturated with a solution of 0.2 n-potassium sulfate to which has been added a saturated alcohol solution of phenol-phthalein at a strength of 10 cc/liter of stock solution. The surplus water is removed and the blotting paper placed in position on the plastic sheet making contact with the drawing pins and the sheet (which is an insulator). The anode consists of a second sheet of blotting paper cut as shown and saturated with the same solution. This is suspended from a laboratory stand, being connected to the conducting wire by means of a crocodile clip and making contact with the horizontal blotting paper at the projecting point. This is the method used by Ramey and Nabor and which permits the hydroxyl ions or colored front to reach the anode. As shown in Fig. 2, the electrical voltage used is 220-v DC and a shunt is placed across the terminals to step down the voltage as required. Further adjustment can be made as necessary using a lamp board in series with the shunt to obtain the

Jan 1, 1958

By Gerhard Derge

Metallurgists have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steel-making of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxi-dizer in rimming steels.' Likewise, the effectiveness of boron as an alloying agent has been demonstrated,2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron. Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B2O3 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. Experimental Procedure No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The must satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron.5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period Of time. However, by using the rotating technique, short runs could be made in

Jan 1, 1947

By Gerhard Derge

Metallurgists have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steel-making of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxi-dizer in rimming steels.' Likewise, the effectiveness of boron as an alloying agent has been demonstrated,2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron. Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B2O3 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. Experimental Procedure No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The must satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron.5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period Of time. However, by using the rotating technique, short runs could be made in

Jan 1, 1947

By S. D. Dahlgren

ORDERED G.P. zones having the cesium chloride structure were found to exist in the bcc iron-rich grains of an Fe-Au-Cu alloy that had been supersaturated with approximately equal atomic percentages of gold and copper, and aged at 400° and 350°C. Streaks and superlattice spots in electron diffraction patterns revealed the presence of the ordered zones in the aged material. The ordered Ll2 structure is commonly found for precipitates in fcc metals (e.g., Ni3A1 in nickelL7') but it is uncommon to find precipitates in bcc metals having the cesium chloride structure. The formation of the G.P. zones caused age hardening of the grains. Samples containing 3.8 at. pct each of gold and copper (with the remainder being iron) were annealed at 95@ or 1125°C in quartz capsules and were quenched by breaking the capsules under water. X-ray diffraction patterns revealed two solid solutions in the quenched samples. One solid solution was bcc and the other was fcc. The microstructure consisted of iron-rich grains of 0.3 mm diam surrounded by a yellow gold-copper-rich grain boundary network. The Au-Cu phase diagram %hows continuous solid solubility of gold and copper with ordered phases forming below 410°C. None of the ordered Au-Cu phases have the cesium chloride structure. Both Fe-Au and Fe-Cu phase diagrams3 show extended miscibility gaps and only terminal solid-solution phases. Consequently, it is reasonably certain the iron-rich grains consisted of an a-phase terminal solid solution, and the grain boundary network consisted of a gold-copper-rich terminal solid solution. Lattice parameters of the quenched solid solutions were consistent with the suggestion that the quenched phases were terminal solutions. The lattice parameter of the bcc phase (2.879A) obtained upon quenching from 950°C was higher than that (2.866A) for pure iron. The fcc phase in this sample had a lower lattice parameter than that for a 50 at. pct Au and 50 at. pci Cu solid solution, i.e., 3.866 compared to 3.877A. The lattice parameter for the 50 pct Au and 50 pct Cu solid solution was interpolated from data for Cu-Au solid solutions.4 More gold and copper were soluble in iron at 1125°C than at 950°C as indicated by a 0.012A increase in the bcc lattice parameter for a sample quenched from 1125°C. After the alloy had been quenched from 950° and 1125°C, the bcc lattice parameters were 2.879 and 2.891A1 respectively G.P. zones having the cesium chloride structure-which formed during low-temperature aging—were detected by electron diffraction and observed with electron transmission microscopy. In Fig. 1, the asymmetrical streaks parallel to ( 100) directions indicate that platelike G.P. zones had formed parallel to (100) planes of the matrix. The direction of streak asymmetry shows that the bcc unit cell of the G.P. zones was larger than the bcc cell of the matrix. The ordered cesium chloride structure is indicated by low-intensity superlattice spots at 010 positions which are nonallowed for bcc structures. The superlattice spots are streaked; therefore they are from the G.P. zones and are not caused by rel-rod effects of a thin matrix phase. The appearance and size of the zones observed in electron transmission microscopy and the appearance of the asymmetrical streaks in the electron diffraction patterns for the Fe-Au-Cu alloy were the same as those observed for a similarly treated Fe-Au alloy.' Ordered G.P. zones were detected also for an Fe-Au-Cu sample aged only at 400°C. The production of the ordered cesium chloride structure zones by low-temperature aging of super-

Jan 1, 1968

By W. F. Hosford, E. W. Kelley

Deformation studies have been conducted at room temperature on single crystals of magnesium and magnesium alloys with thorium and with lithium. Single crystals oriented to suppress shear on the easily activated basal slip systems were deformed by plane-strain compression. Compression along the C axis was accommodated by {1011} banding. Compression perpendicular to the unconstrained c axis activated {1012} twinning, and, after virtually complete twinning, deformation continued by {1011) banding in the twinned material. Compression perpendicular to the constrained c axis was accommodated by the simultaneous operation of (1012) twinning against the constraint and (1011 ) banding. Although this orientation was favorable for {1010)(1210) prism and {1011}(1~10) pyramidal slip, these modes were not observed in pure magnesium or in Mg-0.5 pct Th. However, {10i0)(1~10) prism slip was observed in crystals of Mg-4 pct Li during compression perpendicular to the constrained c axis. Fracture in all materials occurred parallel to (1124) or {l~il) depending on the orientation and composition of the specimen. THE mechanical behavior of the hcp metals is strongly anisotropic. Although several slip systems have been reported the slip is cpmmonly in the directions of closest packing, the (1210),' and this does not produce strains parallel to the c axis. Hence the inherent anisotropy. The deformation mode most easily activated in magnesium at room temperature is (0001)(1210)- basal slip. Also {1010}(1~10) prism slip and {1011)(1210) pyramidal slip have been reported, primarily at elevated temperatures.2"4 However, at room temperature the shear stresses to activate the prism and pyramidal modes are roughly a hundredfold greater than that required for basal slip.'j4 Thus prism and pyramidal slip may be expected only under special conditions of loading. Strains normal to the basal plane can be produced by twinning, however. Many twinning modes have been reported for magnesium,' with (1012) twinning the most common and relatively easy to activate. Magnesium can deform by (1012) twinning when stressed along the c axis jn tension, but not in compression. In contrast, (1011) twinning is activated by compression along the c axis and not by tension. In addition to primary twinning, secondary twinning or slip can occur within the reoriented material of primary twins.' In general at least five independent shear systems must be active to bring about an arbitrary shape change such as that in the individual grains of a deforming polycrystalline material.' Because basal slip can_ provide only two independent shear systems and (1012) twinning can only accommodate an extension of the c axis, other deformation modes must be active in magnesium for an arbitrary shape change to occur. The purpose of this investigation has therefore been to study the various deformation modes in magnesium at room temperature, with special emphasis on those modes that are less easily activated. The effect of the alloying elements, thorium and lithium, has also been investigated. In polycrystalline aggregates, unambiguous identification of deformation modes is extremely difficult and the direct evaluation of the resolved shear stresses to activate them is not feasible. On the other hand, uni-axial tension and compression experiments on single crystals may not activate some of the- deformation modes because basal slip and/or {1012) twinning cannot be suppressed in most orientations. However, it should be possible to activate all possible deformation modes using oriented single crystals and plane-strain compression. Identification of active deformation systems and evaluation of the resolved shear stresses required to activate them should be facilitated. Wonsiewicz and Backofen have recently completed an investigation of the plasticity of pure magnesium crystals at various temperatures utilizing plane-strain compression and selected crystal orientations. This technique has also been used in the present work. The seven orientations selected for study are indicated in Table I. Plane-strain compression along the c axis (orientations A and B) should activate some deformation mode _other than basal, prism, or pyramidal slip, or (1012) twinning. In orientations C and D, prism or pyramidal slip would be expected to take place. When the compressive load is applied perpendicular to an unconstrained c axis (orientations E and F) the three slip modes should be suppressed but not (10i2) twinning. In orientation G, basal slip should occur.

Jan 1, 1969

By A. L. Barnes, A. M. Rowe

A heat transfer study was made of hot gas injection into oil shale through wells interconnected by vertical fractures. This analysis involved the simultaneous numerical solution of a nonlinear, second-order partial differential equation that describes two-dimensional conduction heat transfer in oil shale and a nonlinear first-order partial differential equation that describes convection heat transfer in the fractures. Three nonlinear, temperature-dependent coefficients were used in this work; they are thermal conductivity, thermal capacity and retorting endothermic heat losses of oil shale. Vertical fractures were considered to be of finite height. Although vertical conduction heat transfer was not considered, an estimate of the error resulting from this limitation was made. The effects of injected gas temperature, injection rate, system geometry, cyclic injection and time upon retorting efficiency were investigated. Results from this study show that the rate of retorting oil shale is a direct function of both injection temperature and rate, and the theoretical producing air-oil ratio:(AOR) is an inverse function of temperature. Retorting rates are constant until "breakthrough" of the 700 F isotherm at the producing well, assuming constant injection parameters. Retorting rates for bounded systems are higher than the analogous unbounded systems and likewise AOR's are less. The use of an alternating injection-soak routine with high injection rates is less efficient than continuous injection at lower rates. These results indicate that injection temperatures on the order of 2000F or greater may give theoretical AOR's in the economic range. INTRODUCTION Over half of the known oil shale reserves are located in the U.S., and most of them lie in the Piceance Creek basin of Western Colorado. The Colorado oil shale outcrops on the edges of the Piceance Creek Basin. At the outcrops the shale beds are relatively thin, from 25 to 50 ft thick. In the center of the basin the oil shale is as great as 2,000 ft thick and is covered with 1,000 ft of overburden. It has been estimated that there are over 1,000 billion bbl of oil in shales having an oil content over 15 gal/ton in this basin. Oil shale does not contain free oil but an organic matter called kerogen. Kerogen yields petroleum hydrocarbons by destructive distillation. It must be heated to approximately 700F, at which temperature it decomposes into shale oil, gases and coke. The U.S. Bureau of Mines and, more recently, oil companies have conducted considerable research on surface retorting methods to economically recover oil from this shale. Another approach to exploit the oil shale deposits, in particular that portion having 1,000 ft of overburden, is to retort the oil shale in place and produce the liquid and gaseous hydrocarbons through wells drilled into the shale. Some research has been done on this approach.l,2 There are several variations to the in situ retorting approach. These variations fall into one of two groups, depending upon the geometry of the system: (1) retorting in a highly fractured or broken up matrix; (2) retorting from single fractures between production and injection wells. The latter is the group studied. Several investigators,3-6 using various assumptions, have studied flow of heat through horizontal systems. The objective of this work was to make a heat transfer study of in situ retorting oil shale by hot gas injection through wells interconnected by single vertical fractures of finite height. The oil shale thermal conductivity, thermal capacity and retorting endothermic heat losses were considered to be functions of temperature. A knowledge of the

Jan 1, 1969

By R. F. Domagala, D. J. McPherson

Iodide zirconium was combined with calculated amounts of ZrO2 or master alloys and arc-melted. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat treated specimens permitted construction of the binary phase diagram from zirconium to ZrO2. Oxygen additions to zirconium raise the transformation temperature as well as the melting point. Features of the diagram include the peritectic formation of beta, the formation of alpha directly from the melt, an intermediate phase ZrOB with a' range of homogeneity, and a eutectic between alpha and Zr02. PHASE relationships in the Zr-0 system were determined in the range 0 to 66. 7 atomic pct 0 (ZrO,). Arc-melted alloys were annealed at temperature levels between 600" and 2000°C. Determination of the phase boundaries was accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to determine solidus curves, and X-ray diffraction work was employed to study the lattice parameters of the a solid solution and the phase ZrO,. Experimental Procedures Westinghouse "Grade 1" iodide zirconium crystal bar (approximately 99.8 pct pure) was employed for the investigation. This material is substantially free of the impurity inclusions characteristic of most zirconium metal. Previous work has shown it to be the most satisfactory grade for phase diagram studies. The zirconium crystal bar, as-received, was coated with corrosion product from autoclave tests by which its grade designation is determined. The bars were sand blasted lightly, pickled for 1 min in a 20 pct HN0,-5 pct HF aqueous solution, rinsed in water and acetone, and dried. The bars were rolled to about 1/32 in. strip, cut into 10 in. lengths, and pickled again. The material was sheared to approximately Y4 in. squares, cleaned with acetone, and stored for use. Two pounds of specially prepared "chemically pure," and 100 grams of spectrographic grade ZrO, were obtained for the preparation of alloys. The "Specpure" ZrO, was obtained from Johnson, Mat-they Co.. Ltd.. and Titanium Alloy Manufacturing Div. of National Lead Co. supplied the other grade of oxide. The "chemically pure" material (henceforth referred to as C.P. ZrO,) was used for the preparation of all alloys employed in the determination of phase relationships. A limited number of alloys were prepared with the "Specpure" oxide to recheck certain phase boundaries. Analyses of the two grades of oxide are given in Table I. The C.P. ZrOI was received in powder form, not suitable for arc melting. Therefore, this material was compressed to wafers 1 in. in diameter and about Vn in. thick. These were segmented and stored for use. The "Specpure" material, in the form of small granules, was suitable for use in the as-received condition. A nonconsumable electrode arc-melting furnace was used to prepare alloys. A water-cooled copper crucible and tungsten-tipped electrode were employed. The material was placed in the crucible and rapidly melted under a protective atmosphere of helium gas by striking the arc on a tungsten stud and directing it upon the charge material. Details of operation, including drawings of this type furnace, have been published.'

Jan 1, 1955

By G. A. Vissac

The only fine coal washer with proved automatic controls, the feldspar jig is capable of good efficiencies even at low separating gravities, handles a variety of products, and treats 150 tph and over. IN continental Europe the feldspar jig is used almost exclusively for cleaning the fine sizes of coal; it operates with an artificial bed, made up generally of pieces of feldspar or of any other hard and heavy rock with good cleavages. A primitive form of this machine requiring close supervision was used in this country years ago, but output was small. The modern machines are generally air-pulsated Baum-type jigs, with capacities up to 150 tph, and treat sizes from % in. to 0, usually previously dedusted or deslimed. These jigs are equipped with very accurate and sensitive automatic controls insuring satisfactory operation even at low separating gravity and with feeds irregular in quality and quantity. This paper will deal more particularly with coal cleaning separation, but the technical studies apply equally to all minerals. Theory of the Feldspar Jig To understand fully the operation of the feldspar jig and to appreciate its potential value, it is necessary to measure and analyze the motion of small particles of various specific gravities, falling in various media, under various conditions. As no practical formulas were available for that purpose, the writer has developed new theories and established new sets of formulas, which cannot be demonstrated here. They are applicable to all minerals and to many problems of coal or mineral concentration. These formulas do not pretend to absolute accuracy, but results, tested by comparison with experimentally recorded data, are sufficient for practical purposes, as they give definite indications of trends, relative values, and order of magnitude of the many factors involved. For pulsating motions no earlier formulas are available. In the case of continuous currents or motions, such formulas as Rittinger's, Allen's, or Stokes', over a hundred years old, apply only to special shapes and sizes of particles, involve factors and coefficients difficult to measure or appreciate, and deal only with free motions. They are of little use in solving practical problems. Units used with the formulas presented here are in the CGS system. Lateral friction and suction have been taken into account according- to methods currently used in aerodynamics, and only hindered motion is dealt with. As the feldspar jig is primarily intended to create a fluid bed condition, the mixture of fluids and solids obtained is homogeneous, and the apparent specific gravity of the separating medium is calculated accordingly. For instance, if 20 pct of the volume is coal and shale, with an average of 1.60 sp gr, in a liquid of 1.10 sp gr, the actual specific gravity of the separating fluid is 0.80 x 1.1 + 0.20 X 1.6 = 1.20. The fundamental equations are as follows: The general motion of a particle falling in a medium of specific gravity equal to u, hindered motion. is dv/dt = g/Ls [ L (s-u) - u/g v2 [1] g = 981 cm per sec, acceleration of gravity, and L = thickness of the particle of specific gravity (s) and velocity (v). The initial acceleration dv/dt = g (1-u/s ) [2] is a function of the specific gravity of the particle, only for a given medium, and independent of its dimensions—an ideal separating condition. The terminal velocity Vt = gxL- (s-u)/u, [3] for a given value of u, is a function of s and L. Two particles, L, s, and L2 s2, are said to be equivalent if they have the same terminal velocity, and accordingly L1/L2=s2-u/s1-u. [4] Two such particles cannot be separated by continuous currents, in any concentrating device. Because the initial accelerated motion, which provides for efficient separation, is followed by a constant velocity, which has a limiting effect, it is essen-

Jan 1, 1956

By Ihor A. Kunasz

Introduction Lithium minerals occur predominantly in pegmatites which contain mineral assemblages derived from the crystallization of postmagmatic fluids or from the metasomatic action by residual pegmatitic fluids. They have been the traditional sources of raw materials for ceramic and chemical industries. With the discovery of Searles Lake, brines became new sources of lithium. Indeed, the 1960s may well be referred to as the "brine decade" because several brine bodies of significant economic importance were discovered. In the United States, the brines of Clayton Valley, Nevada, are presently exploited by Foote Mineral Co. The brines of the Great Salt Lake of Utah, the Smackover formation, and the Imperial Valley geothermal field, have been defined as important resources of lithium. In South America, new occurrences have been identified in Bolivia and Argentina. At the Salar de Atacama, Chile, new production capacity is scheduled for 1984. Following the termination of the AEC purchase program in 1959, several companies such as Maywood Chemical Co., American Lithium Chemicals, and Quebec Lithium Corp. were forced to close their operations. Nevertheless, with the development of new applications in glass ceramics, air conditioning systems, synthetic rubber, and metallurgy (aluminum potlines), the lithium industry grew steadily, and with the potential application of lithium metal in batteries and nuclear reactors, a healthy growth can be foreseen. New products and new applications are likely to stimulate exploration for expanded, reserves as well as the search for new sources from which lithium could be extracted economically. Geochemistry of Lithium Lithium is the third element in the periodic table. It is the lightest of all the metals, having an atomic weight of 6.938, an ionic radius of 0.68Å and a charge of +1. The geochemistry of lithium has been extensively studied and has been summarized by Rankama and Sahama (1950), Goldschmidt (1937), and Hortsman (1957). The distribution of lithium in igneous rocks is controlled by its size and its charge, and by the (MgO+FeO) / Li2O ratio. In the early stages of crystallization of a magma, that ratio is very large. Consequently, both magnesium and iron are removed by ferromagnesian minerals in preference to lithium which is then concentrated in the residual magma. This results in an enrichment of lithium in silicic rocks and pegmatites (Strock, 1936). Pegmatites are coarse-grained igneous rocks formed by the crystallization of postmagmatic fluids. Minerals within pegmatites may also form by metasomatism (Jahns, 1955). Genetically, the pegmatites are associated with neighboring intrusives. Mineralogically, granitic pegmatites contain feldspar, quartz, and mica as the main constituents and a variety of exotic elements such as lithium, beryllium, tantalum, tin, and cesium, which may or may not occur in economically significant concentrations. Detailed studies by numerous investigators (Cameron et al., 1949, 1954; Hanley et al., 1950; Jahns, 1953, 1955; Page et al., 1953) indicate that pegmatites often exhibit an internal zonal arrangement, with each zone containing a specific suite of minerals. The lithium minerals are usually found in the intermediate zones, and although as many as 13 zones have been recognized by Cameron, et al. (1949), a complete zonal arrangement is rarely found. Zoning of pegmatite bodies has also been observed on a regional basis. The regionally zoned pegmatite sequences exhibit mineral assemblages and complexity according to their re-

Jan 1, 1983

By N. S. Stoloff, R. G. Davies

The annealing behavior of a heavily cold-worked FeCo-V alloy has been studied at temperatures both above and below Tc, the critical temperature for ordering. It was found that re crystallization and grain growth can take place below Tc in the ordered state and that, in agreement with results for fcc alloys, order retards grain growth. The activation energy for pain growth is -55 kcal per mole in the disordered condition; it was not possible to assign a value to the activation energy for grain growth below Tc because the degree of order is changing rapidly over the temperature interval investigated. Precipitation of an fcc y phase was observed upon annealing the cold-worked alloy at temperatures of 675°C and below. SINCE it is known that diffusion constants are greatly affected by long-range order,' it is not unreasonable to anticipate that order will influence the diffusion-controlled phenomena of recrystallization and grain growth. In the course of a study of strain aging of ordering alloys around the composition Ni3Fe Vidoz, Lazarevic, and cahn2 noted that a disordered cold-worked alloy annealed at a temperature T1 just below Tc will order but not recrystallize; Tc is the critical temperature for order. The same alloy annealed at a temperature T2 just above Tc, or an alloy of different (nonordering) composition annealed at either T1 or T2, will recrystallize after equivalent amounts of cold work. Initially Selisskii and coworkers,3,4 who examined a series of cold-worked and annealed bcc Fe- Co alloys, reported that alloys forming the B2 FeCo super lattice could not be recrystallized below Tc. However in a later paper5 it was shown that FeCo ordered alloys could be recrystallized below Tc. Thus the first question to be answered by the present investigation was whether or not a heavily cold-worked Fe-Co-V alloy could be recrystallized below Tc. When it was found that the alloy would indeed re-crystallize below Tc, the influence of long-range order upon subsequent grain growth was studied. EXPERIMENTAL PROCEDURE The grain-growth measurements were made upon FeCo-2 pct V wire of 0.031 in. diam; the alloy was the same as that used in an earlier study of the mechanical properties of FeCO-v.6 The wire was produced by cold swageing and drawing a rod 0.125 in. diam that had been quenched into iced brine from 850°C to disorder the alloy; the initial grain size was 0.05 mm. Rates of grain browth were measured after isother-mally annealing the wire in the temperature range 675° to 825°C; T, is -720°C. Grain diameters were measured on the transverse cross section of the wires. The line-intercept method of determining the grain diameter was used; conventional light photomicrographs were taken when the grain size was greater than 10 . Carbon replicas were produced and examined in the electron microscope if the grain size was less than Dislocation configurations after recrystallization anneals were studied by electron transmission microscopy of foils produced by cold rolling a 0.125-in.-thick strip of the quenched material to 0.012 in. The foils, after heat treatments similar to the wire samples, were thinned by electropolishing in a chromic-

Jan 1, 1967

By W. S. Stahmann, F. W. Bowdish

Previously published experimental data showing that both collectable and non-collectable sulfide films may be formed on chrysocolla were analysed, and chemical mechanisms were proposed for the formation of the films. A special technique was developed by which the quantity of sulfur adsorbed was determined for samples sulfidized under different conditions of pH and soluble sulfide concentration. The data on sulfur adsorption were used together with the expression for the equilibrium constant for the proposed reaction to indicate the validity of the chemical mechanism theory. A recent paper 1 about contact angle studies on chrysocolla reported the effects of pH value and sodium sulfide concentration during sulfidization upon the character of the surfaces produced. In each experiment the surface of a specimen of chrysocolla was prepared by grinding it with fine abrasive and washing it in tap water. The specimen was then placed in the sulfidizing solution for 10 min, rinsed in tap water, treated for 15 min in a solution containing 30 mg of potassium amyl xanthate per liter, rinsed in distilled water, and tested for air adhesion in a contact angle apparatus. The results, when plotted as in Fig. 1, showed an island representing conditions giving air adherent or collectable surfaces surrounded by conditions giving non-collectable surfaces. Particular interest may be attached to the region of non-collectability to the right of and above the island in Fig. 1, and to the boundry curve separating these two regions. It is apparent that at any pH from 4.0 to 6.0, where a collectable surface may be produced, a sufficient increase in the sulfide concentration results in a non-collectable surface. Thus it appears that too much soluble sulfide has a depressing effect upon the mineral, just as it has in sulfide flotation. This paper presents some speculations regarding the chemical mechanisms by which the collectable and non-collectable sulfide films may be formed and reports on a physical-chemical study intended to support these speculations. THEORETICAL CONSIDERATIONS The experimental results presented in the previous paper were analysed in several ways in an attempt to understand better the chemical mechanisms involved. For several points on the boundary to the right of the region of contact in Fig. 1, molar concentrations of H+, OH-, HS-, and S= ions, as well as various ion concentration products, were calculated. Following the reasoning of Wark and Cox, 2,3 no single kind of ions may be credited with causing depression of the surface because none of them have a constant con-

Jan 1, 1968

By Nicholas J. Grant, H. C. Chang

Microscopic observations during creep tests were made on AI-20 pet Zn, 80 pet Ni-20 pet Cr, and 25 and 3S aluminum specimens. All these materials failed in an inter-crystalline manner under certain stress and temperature conditions. Particular atten-tion was given to the initiation and propagation of intercrystalline cracks in coarsegrained AI-20 pct Zn specimens. The geometry of the grains and grain boundaries in these specimens was known before the tests. On the basis of the observations and a knowledge of the interaction between grains and grain boundaries, a mechanism of intercrystalline fracture and propagation of the fracture has been proposed. METAL, and alloy fracture occurs essentially in two ways: transcrystalline and intemrystalline. In the past most of the work done in this field was centered on the determination of stress criteria for fracture. The specimens used for these studies were tested under varying conditions of stress state, temperature, and strain rate. Unfortunately, very little attention was given to the initiation and propagation of the fracture, whereas the nature of fracture was examined closely only after failure. Several extensive reviews of these studies have been published by Orowan, Smith, Barrett, and Petch.1, 4 It is well known that a material which exhibits a ductile and transcrystalline fracture can be made to exhibit a brittle and intercrystalline fracture by modifying its composition and by heat treatment. This modification may or may not result in microscopically observable precipitation in the grain boundaries." In the creep of any one alloy the transition of transcrystalline to intercrystalline fracture is a function of stress, strain rate, and temperature." The tendency for intercrystalline fracture to occur increases as the strain rate decreases and the testing temperature increases. Extensive work on high purity aluminum (99.995 pet) under creep conditions showed the importance of the interaction between grains and grain boundaries, and the different responses of grain and grain boundaries to the variables: stress, strain rate, and temperature.7, 8 It was also shown that grain boundary deformation necessarily has to be accommodated in the grains by various deformation means as. for example, fold formation. The type of fracture resulting from the creep of high purity aluminum was invariably found to be transcrystalline. On the other hand, 2S and 3s aluminum were, under certain conditions, found to fracture in an intercrystalline manner." One reason given for this was that the grains could accommodate to a lesser extent the deformation of the grain boundaries.19 It was decided to examine this line of reasoning in greater detail and to investigate the particular interactions between grains and grain boundaries that result in the incidence and progression of inter-ct,ystalline fracture. It is also the purpose of this paper to show where and how intercrystalline cracks start and how they propagate to result in fracture. Several alloys—Al-20 pct Zn, 80 pet Ni-20 pet Cr, 2S and 3s aluminum-— were used for this study, but attention was paid mainly to the behavior of an A1-20 pet Zn alloy, since its general creep behavior has been established." From the results of this study a mechanism of intercrystalline fracture is proposed. Experimental Procedure The experimental procedure was similar to that used in previous work and has been detailed elsewhere.' Two parallel flat surfaces were milled from an originally round specimen, giving a gage portion which was 1x0.09X0.17 in. Some round specimens, 1/4 in. round by 1 in., were also tested. The A1-20 pet Zn specimens. which were annealed at 1030°F for 24 hr, showed two to four grains across the width of the test bar, and most of the grains occupied the whole thickness of the specimenu. Before some of the specimens were subjected to creep, the grain arrangement was mapped out in a development drawing, Fig. 1. The initiation and

Jan 1, 1957

By P. T. Carter, A. B. Murad, H. B. Bell

The distribution of manganese and oxygen between molten iron and FeO-MnO-SiO2 slags not saturated with SiO2 has been determined and used to calculate activities of MnO and SiO2 in MnO-SiO2 slags. These were found to be intermediate between the corresponding activities in FeO-SiO2 and CaO-SiO2 slags. THE equilibrium constant for the reaction between molten iron containing manganese and slags containing FeO and MnO, namely: FeO(slag) + Mn = MnO (slag) + Fe(1iquid) is most conveniently represented by: (MnO) Kmn== (FeOHMn] [Fe] is omitted, since for dilute solutions of manganese in iron, afe is approximately constant. When activities are used for (MnO), (FeO) and [Mn], Kmn is a true equilibrium constant and will apply to all types of slags, but when weight percentages are used, the values obtained for Kmn for different slags vary considerably. The equilibrium between iron containing manganese and relatively pure FeO-MnO slags has been investigated by several workers;1-4 the most recent investigation reported is that of Chipman, Gero, and Winkler.4 Their results, corresponding to slags containing up to 4 pct SiO2, were represented by the equation: 6440 log KMn = +2.95 In this case both slag and metal may be assumed to be ideal solutions, therefore the values of Kmn so derived represent the true constant for the manganese reaction. As the molecular weights of MnO and FeO are almost equal, weight concentration of these oxides may also be used in the above expression. Acidic oxides such as SiO2 and P2O5 affect the activities of FeO and MnO differently, so that when total concentrations by weight of FeO and MnO are used in the above expression for Kmn the values obtained are no longer constant. These will be denoted by K'mn. Körber and Oelsen5 investigated the manganese reaction using silica-saturated iron-manganese-silicate slags and found: 7940 logK'mn =3.172 This corresponds to Kmn values much higher than those obtained for pure oxide slags. The results of Körber and Oelsen, and Chipman, Gero, and Winkler are summarized in Table I. In the present investigation it was decided to study the manganese reaction using iron-manganese-silicate slags not saturated with silica, and which fell mainly between the orthosilicate join 2FeO . SiO2 - 2MnO.SiO2 and the FeO-MnO side of the ternary system FeO-MnO-SiO2. It has been shown" that the phases present in solidified slags of this part of the diagram are (FeO, MnO) and (2Fe0.Si02, 2Mn0-SiO,) solid solutions. Such an investigation would be of interest in deoxidation and also gives information on activities in liquid slags. This equilibrium has not as yet been investigated successfully. Hilty and Crafts7 attempted to examine this reaction in a rotating crucible furnace, but were unable to obtain suitable slag samples. In the present investigation one series of experiments was carried out in a rotating crucible furnace, because the success of Taylor and Chipman8 with such a furnace in their study of oxygen distribution between molten iron and (CaO, MgO) — FeO-Si0, slags suggested that it would minimize contamination of the slag by the crucible material. A second series was carried out using a wire-wound resistance furnace. Rotating Crucible Furnace Experiments In all cases the metallic charge consisted of 800 to 1000 g Armco iron containing 0.02 pct C, 0.03 pct Mn, and traces of Si. Manganese and silicon additions consisted of electrolytic manganese (99.9 pct)

Jan 1, 1953

By Matti J. Saarivirta

The relative machinabilities of the precipitation-hardenable Cu-0.9 pct Cr, Cu-0.25 pct Zr, and Cu-0.9 pct Cr-0.25 pct Zr alloys are improved from 18 to 80 pct by 0.75 to 1.25 pct Pb. The Lead also improves the tensile strength, hardness, ad resistance to softening of the Cu-Cr and Cu-Cr-Zr alloys. When the alloy containing 0.7 to 2.2 pct Cr, 0.10 to 0.25 pct Zr, 0.75 to 1.25 pct Pb, and balance copper is solution-annealed at 1000°C (1830°F) and then aged at 525°C (Y75°F), tensile strength of 65,000 psi, 16 pct elongation, 62Rb hardness, and 84 to 87pct IACS electrical conductivity are obtained. The copper base Cu-Cr, Cu-Zr, and Cu-Cr-Zr alloys have high electrical and thermal conductivities, high strength and resistance to softening at elevated temperatures, but their machinability is poor, i.e., close to that of the pure copper. In the manufacture of various components such as welding electrodes or electrical and thermal conductors it is ofter desirable that the alloy have good machinability for high production rates and long tool life. Thus, alloys that combine these properties may be used not only for existing applications, but for new ones where good machinability is a requirement. This investigation was undertaken to improve machinability without impairing other desirable characteristics of the Cu-Cr, Cu-Zr, and Cu-Cr-Zr alloys. These commercial alloys contain about 0.4 to 1.2 pct Cr, 0.10 to 0.25 pct Zr, and balance copper. Lead was selected as an element that should improve the machinability and possibly other characteristics of the alloy. WORK PROCEDURE This investigation began with a study of the effect of lead on the hardness, tensile strength, electrical conductivity, and machinability of the binary alloy containing 0.10 to 1.30 pct Cr and balance copper. This was followed by an investigation of the effect of lead on the Cu-0.1 to 0.4 pct Zr and Cu-Cr-Zr alloys. The alloys were made from initially oxygen-free copper and for comparison some castings were made from phosphorus-deoxidized Lake Copper. Commercially pure chromium, zirconium, and lead were used for alloying. In melting the chromium was added to molten copper at 1400°C (2550°F), the heat held for 15 min at temperature, and the temperature then lowered to 1350°C (2460°F) when the other elements were added. The alloys were held for 15 min at this temperature and cast into a cast-iron mold. One-kilogram, 3-in.-diam castings were made. An argon cover was maintained during melting and casting to prevent oxidation. The chemical compositions of the alloys are shown in Table I. The micro structure and properties of the alloys were studied in the cast and wrought conditions prior to and after various solution-annealing and heat-treating cycles. The relative machinability was determined as a function of the lead content and compared with the free-machining Cu-lpct Pb alloy. To determine the machinability, 13/16-in.-diam cast specimens were cut by a machine hack saw using a constant cutting speed of 50 fpm, a fixed feed force, and a new blade for each alloy specimen. Molybdenum highspeed steel saw blades, 0.032 in. thick with 14 teeth per in., were used in all tests. No cutting fluid was used. Five tests were made on each specimen and the average elapsed time per test was taken as a measure of the relative machinability for that alloy. The variation of cutting time for each alloy was less than 110 pct.

Jan 1, 1969

R. F. WOOD,* Sandusky, Ohio.-I made a few tests of gun-metal specimens, after I noticed the results on quenching -reported by the Bureau of Standards. The data of one such test are given herewith. The bars were heat treated and quenched before they were machined, and in all cases they were brought up to 700° or 800°. They became extremely brittle,, showed almost no elongation, except such as was caused by the failure of the pieces to fit together after they were pulled, and the tensile stength was reduced from around 35,000 to about 13,000 lb. per sq. in. In addition, the weakening effect of the quenching seemed to be almost as marked when the bar was allowed to slowly air-cool from red to black, and then quenched, as it was by quenching directly from the red heat. Test Bars.-Rough size, 9/16 in. diam. over test section, grips 13/16 in. diam. Cast two in a flask, one on each side of a block 8 by 4 by 1 in. and fin-gated thereto from the grips but not from the test section. Poured with flask in inclined position, with gate to lower end of block and riser from upper end of each test bar. Bars were machined to ½ in. over the test section, after heat treatment. Casting the Bars.-Charge of 1500 lb. consisting of 400 lb. of new metals and 1100 lb. of G turnings and scrap was melted in open-flame oil furnaces and then poured into a 1-ton ladle. From the ladle 150 lb. was poured into a preheated No. 50 crucible, land from this the flasks of test bars were poured. The six flasks are indicated below by the numbers 1 to 6 and the bars in each flask by the letters a and b, thus 4a and 4h, for instance, were the two bars in flask No. 4.

Jan 12, 1919