Search Documents

By Lawrence H. Van Vlack

The energy of the y-iron grain boundary was determined to be 850 ergs per cm2 at 1105°C. The a/a and the a/y boundaries possess somewhat less energy. The microstructures of several iron alloys are discussed in terms of the interfacial energy relationships. THE dependence of the shape of liquid interfaces upon their energies has been studied for some time.1"3 Recently, Smith' concluded that many of the microstructures observed in metals may be attributed to the energies of the interfaces between the grains and phases. While the energies of liquid surfaces have been measured by numerous different methods: only two attempts have been made to determine experimentally the energy of surfaces involving crystalline solids. Udin, Shaler, and Wulff8 used a procedure introduced by Berggren7 to measure the surface tension of solid copper. It consisted of determining the load required on a thin copper wire so that the surface tension was counteracted, and no net strain resulted. Bailey and Watkins8 sed a different technique and were able to determine both the surface tension of copper and the tension of the copper grain boundary. They measured the contact angle which liquid lead makes against a copper surface. They then calculated the above energies from the surface energy of liquid lead by using the Pb vs. Cu/CuY dihedral angle and the surface groove angle formed during thermal etching. They obtained a value of 1800 dynes per cm for the surface tension of clean copper and approximately 640 dynes per cm for the tension of copper grain boundaries. The former value was somewhat higher than Udin's value of 1500 dynes per cm. This paper includes a determination of the energy of the y-iron grain boundary. In addition, the micro-structural relationships of several other metallic and nonmetallic phases with iron were examined and an attempt was made to interpret the observed structures in terms of interfacial energy relationships. Theoretical Considerations In a three-phase material containing a solid and two liquids, there may be two solid/liquid interfaces, one liquid/liquid interface and one inter- granular interface. Liquid/liquid interfacial energies can be measured directly. Therefore, by determining the energy of such an interface and by measuring the required interfacial angles: the energies of the interfaces involving solids may be obtained.10 They may be shown schematically as in Fig. 1. The above procedure requires the following assumptions: 1—The interfacial energies are, in general, unaffected by boundary orientation, and 2— the shapes of the interfaces are unaltered between annealing and sectioning for microscopic examination. The first assumption is good to a first approximation as shown by Dunn and Lionetti11 except for a few critically orientated boundaries. Two conditions may alter the shape of a boundary upon cooling: 1—Precipitation of dissolved material upon one side of the interface, and 2—a change in volume during the transition from one phase modification to another. The former must be detected by microscopic observation. The latter may become appreciable in systems containing an interface between two liquids which solidify after annealing. However, possible movement of the two-liquid interface may be checked in the system diagrammed in Fig. 1 by measuring 8, for example, and comparing it with its value as calculated from the other interfacial angles by: tan8, C11 05 COS- o- + cos 8, cos- The choice of a suitable pair of liquids is limited by several factors. The relative values of the several

Jan 1, 1952

DEVELOPMENT of a chemical process for the extraction of pure metals from mill concentrates or metal scrap has progressed beyond the pilot plant stage and may prove an important adjunct to present smelting and refining methods if initial commercial operations prove economically successful. Developed by the Chemical Construction Corp., the new process involves the treatment of oxide and sulphide ore concentrates by chemical methods, instead of the usual smelting and refining techniques. Several of the many applications are now scheduled for commercial use. Refiners using the new process will prepare ore concentrates by standard flotation methods, introduce the concentrate as a slurry into an autoclave along with water and an acid or ammonia. From the resulting leach solution, recovery of individual metals is made by use of suitable reducing agents. By varying conditions during treatment, different metals in the ore are produced separately as pure powders, which may be pressed into forms ready to market, or in the case of copper, extruded as rods or pipe. The reagents are generally recovered. By manipulating the variables during reduction, selective separation of nickel, and/or cobalt, and/or copper can be made simultaneously. The separation is a continuous operation. Low metal prices are not immediately in view because of the tremendous demand at this time. However, reduced metallurgical treatment costs will allow economical mining of orebodies with lower metal content, permitting increased production to meet demand. Although the practical horizon for use of the new process appears to be limitless, one factor may enter into its employment. Just how low grade a concentrate can be economically used is unknown. In addition, for present practical considerations, only metal below zinc in the electromotive series may be processed. Each commercial application requires specific technique adaptation and pilot-plant data for engineering design. A nickel-cobalt-copper process has been researched and piloted in collaboration with Sherritt Gordon Mines, Ltd., for the firm's Lynn Lake properties. In addition, processes were tailored for cobalt concentrates of Howe Sound Mining Co., and National Lead Co., in view of the urgent need for this specific metal. Major General William N. Porter, president of Chemical Construction, says of the new process, "piloting experience has shown that production cost, from ore concentrates to pure metals should be considerably below current costs." Other savings may be realized by cutting transportation and personnel costs, and by reducing the time lag between mining and pure metal from months to a matter of hours. First commercial use of the process will start sometime this summer. Chemico is slated to finish building a $2.5 million cobalt refinery for Howe Sound Mining near Salt Lake City. The plant is expected to raise world cobalt production by 40 pct. The plant will process 35 tons of 20 pct cobalt concentrates from Howe Sound's Blackbird mine near Cobalt, Idaho, daily. Yearly production is expected to reach 2000 tons of pure metal, about one half of U. S. consumption in 1950. Steps in the Howe Sound application of the process are: 1. Acid oxidation leach. 2. Filtration (residues thrown away are insoluble compounds-gangue, iron, arsenic). 3. Cementation (for Cu removal because Cu content is too low for recovery). 4. Reduction from ammoniacal solution. 5. Separation of Co and Ni as mixed metals (95 pct Co and 5 pct Ni). 6. Recovery of ammonium sulphate. Under construction at the Fredericktown, Mo., mine of National Lead is a $5 million refinery sched- [ ]

Jan 1, 1952

By R. W. Olson, A. L. Benham

Viscous fingering was studied as it occurred in an open Hele-Shaw model (1 ft x 4 ft x 1/16 in.); it was also studied in the same model packed with 80-mesh glass beads during miscible displacements under unfavorable viscosity ratio conditions. It was determined that the lengths of 20 elements of the front were distributed normally around the average position of the combined elements under all conditions. Represented by the normal distribution, the length of the viscous fingers grew linearly with the distance traveled from the point of finger formation, increased with displacement velocity, and increased with increasing mobility ratio. Results obtained during the first few inches of displacement were of little or no use in predicting finger growth and/or finger length throughout the 4-ft model since the point of finger initiation cannot be predicted and would often occur several inches from the point of injection with either positive or apparent negative coordinates. The fingering occurring during a miscible slug displacement was much greater than would be predicted based upon the actual mobility ratios between in-place fluid and slug and between slug and following fluid, using the results described above for miscible displacement in the absence of a slug. Many of the experiments in the packed model showed that the rate of growth of the viscous fingers was diminishing toward the end of the displacement in the 4-ft long model, indicating that microscopic mixing, such as diffusion or dispersion, was decreasing the viscous fingering effect. INTRODUCTION Viscous fingering is a manifestation of a finger-shaped interface between displaced and displacing fluids occurring during typical miscible displacement projects for oil recovery. Its cause may be traced to the instability of a viscous fluid being displaced by a more mobile fluid. Viscous fingering takes on important significance in the miscible slug process 1.2 where it may be a dominant factor in determining minimum slug size. Experimental1-3 and theoretical4-7 studies of viscous fingering have been made by other investi- gators. However, an exhaustive study of the variables affecting viscous fingering had not been made. The present study was undertaken in an effort to determine the effects of some of the more obvious variables—such as mobility ratio, displacement velocity, distance displaced, and packing—upon viscous finger length and growth in a small laboratory model. It does not necessarily follow that conclusions reached by studying the results of this model study may be applied to the field. Future studies would have to evaluate the effect of model size on extension of these results. EQUIPMENT AND EXPERIMENTAL PROCEDURES A flow diagram for the equipment used in this study is shown in Fig. 1. Basically, it consisted of (1) a constant-rate pump for the injection of displacing fluid into (2) a model made up of two flat transparent plates spaced a small distance apart and (3) provisions for the production of fluid into a calibrated graduate. The displacing fluid contained a dye which allowed visual observation of finger spacing and length. The pump performed at rates from 2.5 cc/hr to 480 cc/hr, while pumping a light mineral oil into a bladder in a closed glass container holding the displacing fluid. The model was made up of two plates of 1-in. Plexiglass with dimensions 1-ft wide by 4-ft long. These were spaced 1/16 in. apart so that the internal model dimensions were 1-ft wide x 4-ft long x 1/16

By J. Lohrenz, C. R. Clark, B. G. Bray

Procedures to calculate the viscosities of in situ reservoir gases and liquids from their composition have been developed and evaluated. Given a composition expressed in methane through heptanes-plus, hydrogen sulfide, nitrogen and carbon dioxide together with the molecular weight and specific gravity of the heptanes-plus fraction, the procedures are capable of calculating the viscosity of the gas or liquid at the desired temperature and pressure. The procedure for reservoir liquids was developed using the residual viscosity concept and the theory of corresponding states, and was evaluated by comparing experimental and calculated results for 260 different reservoir oils ranging from black to highly volatile. The average absolute deviation was 16 per cent. This is the first known procedure for calculating the viscosity of reservoir liquids from their compositions as normally available, i.e., including the heptanes-plus fraction. The procedure for reservoir gases uses a sequence of previously published correlations. Evaluation of the procedure was accomplished by comparison of 300 calculated and experimental viscosities for high-pressure gar mixtures in the literature. The average absolute deviation was 4 per cent. The calculations are useful for (I) determining viscosities in compositional material balance computations and (2) predicting the viscosity decrease which occurs when gases, LPG, or carbon dioxide dissolve in reservoir oils. INTRODUCTION Methods to predict viscosities of reservoir fluids from the normally available field-measured variables have been presented. Beal,1 Standing,2 and Chew and Connally3 orrelated oil viscosities with temperature, pressure, oil gravity and gas-oil ratio. Carr, Kobayashi, and Burrows4 and Katz et al.5 have presented correlations for reservoir gas viscosities as a function of temperature, pressure and gas gravity. Lie all intensive physical properties, viscosity is completely described by the following function: Eq. 1 simply states that viscosity is a function of pressure, temperature and composition. These previous correlations1- hay be viewed as modifications of Eq. 1, wherein one assumes more simple functions may be used. The assumptions are practical, because the composition is frequently not known. Further, the assumptions are sufficiently valid so that these correlations are frequently used for reservoir engineering computations. In compositional material balance"' computations, the compositions of the reservoir gases and oils are known. The calculation of the viscosities of these fluids using this composition information is required for a true and complete compositional material balance. For reservoir gases, Carr, Kobayashi and Burrows4 have presented a suitable compositional correlation. For reservoir oils, no correlation is available, and data from reservoir fluid analyses have been used7-9 for compositional material balance calculations.* From a theoretical point of view, this is entirely invalid. The reservoir fluid analysis, whether flash, differential, or other process, does not duplicate the compositions which occur during the actual reservoir depletion process, therefore the viscosities measured during reservoir fluid analysis are not those which occur in the reservoir. From a practical point of view, the "error" of using viscosities from reservoir fluid analysis is of varying and unknown significance. One can say qualitatively that the error is greatest where compositional effects are greatest, i.e., for volatile oil and gas condensate reservoirs and pressure maintenance operations. The first requirement to obtain a quantitative estimate of the significance of the error is to develop a reliable compositional correlation for the viscmities of reservoir oils. No such correlation has been available. Consistent with this requirement, the objective of this study was to develop a procedure to predict the viscosity of reservoir fluids from their compositions. Normally, the compositions of reservoir fluids are available expressed as mole fractions of hydrogen sulfide, nitrogen, carbon dioxide and the hydrocarbons methane through the heptane-plus fraction, with the average molecular weight and specific gravity of the latter. The final correlation was to use the composition in this form. While the more challenging objective of the study was the development of a correlation for the viscosities of reservoir oils, the viscosities of reservoir gases were also studied. The end result of the study was a procedure to calculate the viscosities of reservoir gases and liquids suitable

Jan 1, 1965

By C. J. Frosch, J. A. May, H. G. White, C. D. Thurmond

Gallium phosphide epitaxial layers were grown from the vapor phase on undoped single-crystal galliurn arsenide substrates in silica tubes by an open-tube wet-hydrogen process. The epitaxial layers were grown over a range of water pressures at three substrate temperatures. Excess donor concentrations were determined by surface barvier capacitance measurelrzents without removing the layers from the substrates. The excess dmlor concentration, ND-NA, is fo~ind to vary approxilnately inversely with the pressure of water added to the hydrogen carrier gas. This is the relationship that would be expected for singly ionized silicon donors on gallium sites in extrinsic galliunz phosphide, with the silicon coming from the SiO generated by the reaction of hydrogen with the silica tube. An increase in the partial pressure of water in the hydrogen stream decreases the SiO pressure. The results indicate that ni, the intrinsic hole and electrmt concentration for gallium phosphide at the three substrate temperatures, is smaller than the concentration estimated from available data for the density of states effective masses and the energy gap. Mass-spectrographic measurements confirm that the dono?, introduced into gallium phosphide is silicon. The equilibrium concentrations of silicon in vapor-flown gallium Phosphide have been estimated from available thernzodynamic information that includes the solubility measurements of silicon in gallium phosphide in equilibrium with a gallium-rich liquid phase. Satisfactory agreement with the measured silicon concentrations is obtained. FROSCH1 has described an open-tube process for growing single-crystal Gap from the vapor phase by a GazO transport mechanism. The method depends upon the reaction of H20 in an H2 carrier gas with a heated source of polycrystalline Gap which provides the necessary vapor species. When the temperature of these vapor species is lowered, super saturation occurs and single-crystal Gap will deposit on a suitable substrate. Unintentionally doped single crystals of Gap grown by the wet H2 process in silica tubes are n type. Evidence is presented to show that the donor introduced is silicon, and that a qua si-equilibrium model accounts for the inverse dependence of the donor concentration on the water partial pressure and predicts the magnitude of the donor concentrations. Ainslie et al. experimentally showed a similar inverse relationship between the carrier density and oxygen pressure for GaAs. Emission-spectrographic analyses showed a decrease in the silicon concentration with increasing oxygen overpressure for GaAs. Cochran and Foster suggested the theoretical possibility of suppressing silicon contamination by using Ga20 generated by the reaction of gallium with water vapor. 1) EXPERIMENTAL The apparatus and procedures are essentially the same as those described by Frosch.' The apparatus consists of a 25-mm-ID SiO2 tube extending through a controlled high-temperature flat zone for the location of the polycrystalline Gap source and a downstream temperature gradient falling at a rate of about 14°C per cm. The latter provides the region of super saturation for the location of the single-crystal substrate. The partial pressure of water in the inflowing hydrogen stream, pA2, O was controlled by mixing me-tered proportions of dry H2 with H2 saturated with H2O vapor at 0°C. The total gas flows were about 200 cu cm per min in all experiments. The Gap sources were prepared by pulverizing boat-grown polycrystalline ingots to pass a 20-mesh sieve. The substrates were cut from an undoped single-crystal boat-grown GaAs ingot purchased from Monsanto. This ingot had a carrier concentration of about 1015 atoms per cu cm, a resistivity of about 5 ohm-cm, and a mobility of about 5000 sq cm per v sec at 25°C. Substrates with dimensions of 1 by 1 by 5 x lo-' cm were employed. The growth faces were chemically polished (111) arsenic faces. Epitaxial layers, at least 7.5 x 10-3 cm thick, were grown,. This required from 1 to 24 hr depending upon the Pii2Q values and the temperatures. In all of the runs, the source temperatures were 50°C higher than the substrate temperatures. Samples were prepared

Jan 1, 1968

By Henry M. Howe

SECTIONS 1. INTRODUCTION.—In this investigation the meltingpoint and the specific heat of certain artificial silicates were determined by the method of mixtures, using a large platinum-ball pyrometer. The silicates were placed in platinum crucibles on the hearth of a small regenerative gas-furnace (Figs. 1 and 2), and the platinum ball was placed between them. The temperature of the furnace was usually raised very slowly, the behavior of the silicates being observed as they gradually grew hotter; and their temperature was ascertained indirectly from time to time by determining that of the platinum ball, which to that end was temporarily withdrawn from the furnace and immersed in a known weight of water in a calorimeter. The weight and specific heat of water and of platinum ball being known (the specific heat of the latter approximately), it mas possible to calculate the temperature of the platinum ball, which was assumed to have been substantially that of the silicates which surrounded it in the furnace. The specific heat of the silicates also was determined by the method of mixtures. Their temperature having been determined as just described, one of them was dropped into a known weight of water in a calorimeter, whose rise of temperature was then noted. Knowing the weight and initial temperature of the silicate, its specific heat was wily calculated. The reults obtained, especially as regards the melting-point, must be regarded as first approximations. The technical difficulties encountered were so serious as to raise doubts, now from one cause, .now from another, as to the accuracy of most of the results: hence I give but a few, those which were reached without mishap, and with proper observation of the various precautions. The difficulties encountered are referred to again in Section 6. The investigation was carried out in the metallurgical laboratory of the Massachusetts Institute of Technology, and part of. The

Jan 1, 1890

By A. J. Teplitz, J. K. Rodgers, E. M. Pohoriles

This note is presented in order to call attention to a newly developed laboratory apparatus that appears to have interesting possibilities for the study of lost circulation of the pressure-parting type, for a more realistic evaluation of sealing materials for this type of loss, and for investigation of other aspects of hydraulic fracturing. A study of lost circulation, conducted jointly by operating divisions of the Gulf Oil Corp. and the Gulf Research & Development Co., has been in progress for the past few years. Earlier phases of the study dealt with mechanical factors contributing to loss of returns in laminar type sediments.' One aspect of this type of loss which has been widely discussed in the literature and elsewhere concerns the geometry of the fractures into which such losses occur. This subject is not merely a philosophical one, but has an important bearing on procedures for combating lost circulation difficulties and on other well operations. The further course of the collaborative studies previously mentioned has produced some information on this subject which, though limited in amount, is believed to be significant. In several typical cases of lost circulation in laminated shale and sand formations, the wells have been surveyed with instruments2,3 capable of detecting the points of loss with considerable accuracy. These wells were located in the Gulf Coast of Texas and Louisiana, in the Texas Panhandle, and in the Rocky Mountain area. In each of these instances the loss was shown to be occurring at some distance removed from the bottom of the hole and sharply confined to a very narrow interval, less than 1 ft in thickness. It is rather difficult to imagine that fractures of a vertical nature' would be of the limited extent indicated by the surveys in these wells. Furthermore, the high rates of loss at relatively low pressure differentials observed in some of these instances together with the narrow intervals involved would appear to require the radial flow pattern which would be associated with a more or less horizontal fracture plane. In view of the foregoing observations and records of successful squeeze cementing operations, in attempting to construct a laboratory apparatus For simulating pressure induced lost circulation, it was decided that the design should be based on a horizontal type of fracture. It was realized that5,6 Vhe production of horizontal fractures in a formation with non-penetrating fluid requires some mechanism for transmitting vertical components of the hydraulic forces to the plane of parting. This was accomplished, as will be evident in the description of the apparatus that follows, by providing recesses in the wall of the borehole which are believed to be representative of wellbore configuration found in Gulf Coast wells. The possible influence of such borehole irregularities on both pressure fracturing and the treatment of lost circulation appears to have been neglected in many studies of these subjects. It is believed that the present apparatus, incorporating features that take into account some of the factors mentioned, will provide means of gaining a further understanding of pressure induced fracturing and possibly for more realistically evaluating the numerous sealing agents, particularly the non-time-setting materials employed in treating the pressure-parting type of loss. DESCRIPTION OF APPARATUS The test cell used in the laboratory investigations is shown in Fig. 1. A schematic diagram of the entire system is shown in Fig. 2.

Jan 1, 1956

By J. S. Kennedy, A. A. Lerew, C. M. Judson, G. L. Simard

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from. these laboratories." These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that, are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren, machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as. the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite. flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the. selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pet Zn for ZnS) ; and the quartz from Klondike, Mo., analyzed as 99.97 pet SiO2. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from S82 supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1952

By C. W. Phillips, D. N. Frey

A commercial Ti-Fe-Cr alloy, Ti-150, exhibits a martensitic transformation on cooling and two nucleation and growth reactions, one above and one below the Mg-Mf region, on isothermal holding below the single-phase ß temperature range. The reactions were followed by metallographic, X-ray diffraction, and microhardness methods. THE rapidly expanding engineering application of titanium and its alloys makes increasingly urgent an adequate knowledge of the effect of heat treatment on this material. The work herein reported is an attempt to determine certain aspects of the behavior of a commercially available alloy, Ti-150, during heat treatment. The alloy, with a nominal composition of 2.7 pct Cr, 1.3 pct Fe, 0.25 pct 0, 0.02 pct N, and 0.02 pct C, was received in the as-rolled condition as a 3/4 in. round. Slugs 0.11 to 0.12 in. thick were cut under a coolant using a silicon carbide wheel. Preliminary work established that the alloy consists of two phases, a (hexagonal close-packed) and /3 (body-centered cubic), at temperatures below 1750" to 1775"F, and of only /3 phase at higher temperatures. The slugs were heated for 1 hr in air at 1800°F to form a single-phase /3 matrix, then transferred to molten tin (1250° to 1650°F) or lead (1150°F and below) for isothermal holding. Holding temperatures ranged from 700° to 1650°F, times from 0.001 to 23 hr. The treated slugs were then sectioned, one part for metallographic examination and diamond pyramid hardness, the other, after deep etching to remove the high oxygen surface,' for comparative lattice parameter determination and X-ray phase identification. Hardness measurements were taken on the lightly etched surfaces of the metallographic specimens; a 1000 g load on a 136° diamond pyramid was used. Five impressions on each sample were made and the average of the hardness calculated. The use of microhardness measurements to follow the course of an isothermal transformation reaction is undesirable because of the possibility of wide differences in microconstituent hardness.' They were used in this case, however, because of the small amount of material available. At the higher transformation temperatures, where the above-mentioned objection was apparent, the readings were proportioned to correspond to the estimated ratio of transformed and untransformed constituents present. At lower temperatures, resulting in much finer microconstituents, the microhardness measurements were more uniform. The standard deviation of the mean of five impressions calculated from these latter values was 4.2 DPH. Employing 2a limits (probability 0.95) the experimental error of the hardness measurements averages was 8.4 DPH. The etchant used was composed of one part glyc-erol and one part 48 pct hydrofluoric acid." Of a number of etches tried, this one appeared most satisfactory. All micrographs were taken at 500X magnification and with oblique lighting to permit easier identification of the acicular structure resulting from rapid cooling. No advantage was gained by using polarized light for metallographic examination. Phase identification and lattice parameter measurements were made with a North American Philips high angle spectrometer in conjunction with a recording potentiometer. Considerable difficulty was encountered with some of the lattice parameter measurements because of the extreme broadness of the few diffraction lines obtained from samples consisting mainly of strained, untempered, quenched structures.

Jan 1, 1953

Jan 1, 1893

By J. Chipman, N. J. Grant, J. H. Walsh, T. B. King

WITH the development of adequate sampling and analysis techniques, much information has been obtained concerning the behavior of hydrogen in the steel bath during the course of steelmak-ing operations. From studies of this type it has become clear that the slag has an important role to play in determining the hydrogen content found in commercial products. A knowledge of the behavior of hydrogen in slags is necessary to round out our knowledge of hydrogen in steelmaking practice; with this information we are better able to assess practical methods of control. In this paper a method developed for analyzing slags for hydrogen content, studies of the solubility of hydrogen in synthetic slags, and studies of the variation of hydrogen content in slag and steel in industrial heats will be described. Previous Work—While very little has been done in the past to determine the hydrogen content of metallurgical slags, measurements have been made on such slag-like materials as geologic magmas and glasses. Goranson as made extensive studies of the solubility of water in natural and synthetic granites. Many workers have investigated the solubility of gases in synthetic and commercial glasses, but the recent work of Russell" is the most extensive. Russell found that the solubility of water in glass was proportional to the square root of the water vapor pressure in water vapor-oxygen mixtures. It was found that the solubility could either increase or decrease with temperature depending on the glass composition. Wentrup, Fucke, and Rief,' and Piper, Hagedorn, and Backes' have extracted hydrogen by holding a slag at 1300" and 800°C respectively in vacuum. Wentrup et al. reported hydrogen and water vapor as evolved together while Piper et al. passed the evolved gases from the hot extraction treatment over hot ferromanganese to reduce the evolved water vapor to hydrogen and, therefore, reported the analyses in terms of total dissolved hydrogen. Yavoiskii has reported hydrogen and nitrogen analyses on steelmaking slags. Dobrokhotov, Povol-skii, and Khan have studied the hydrogen content of basic open hearth steel under slags of varying viscosity. These authors reported that the hydrogen content of the steel bath increased as the fluidity of the slag was increased by the addition of bauxite. They recommended that a viscous slag be used and the steel tapped without deoxidation in the furnace to ensure a low final hydrogen content. Analysis of Slags for Hydrogen Development of Apparatus—The vacuum fusion analysis equipment described by Shields, Chipman, and Grant" was modified for the analysis of slags." This method depends upon the reduction of water in the slag to hydrogen, which is readily determined by the method used for hydrogen in steel. Preliminary experiments were made with a eu-tectic ferrosilicon melt as the reducing agent. Other experiments included the use of graphite and molybdenum crucibles. The ferrosilicon alloy bath was found to produce a thick coating on the furnace tube which could adsorb hydrogen. Graphite produced CO by the reduction of FeO, MnO, and SiO2 in such quantities that analysis for hydrogen was virtually impossible. Molybdenum, while giving a low blank value, could reduce the slag sufficiently to produce a volatile oxide which again was found to adsorb hydrogen. The arrangement finally adopted is shown in Fig. 1. The molybdenum sheet served as the induction-heated susceptor, and was separated from the escaping gases by alumina guide tubes. An outer jacket of alumina protected the quartz furnace tube, and alumina and quartz stools completed the assembly. The falling sample is shown wrapped in aluminum foil, 0.002 in. thickness, which acted as the reducing agent' This foil was careful'~ washed in acetone and an d and then dried in hot air before wrapping the weighed slag sample for charging into the apparatus. Investigation of the hydrogen content of the aluminum foil itself showed that a small quantity of hydrogen was released in vacuum, but had no relation to the weight of the aluminum charged. This quantity of hydrogen was

Jan 1, 1957

By James M. Stapleton

IT has long been recognized by blast- furnace men that correct top distribution of materials is very important in efficient and economical furnace operation. Thousands of experiments on top design, filling, sizing, and other operations have been carried out to improving furnace performance by securing uniform distribution. Many of these experiments have worked out satisfactorily and have been passed along to the industry. Many of them have been discarded and forgotten. It has been the custom to judge the results of such experimentation by the results shown in improved or lowered furnace efficiency. While the effect on furnace practice will have to continue to be the final criterion of experimental changes, it has always been a desire of blast-furnace men to ascertain the reason for failure or success. Efficiency in the blast furnace approaching the maximum can be measured in several ways: (I) by actual operating results as revealed in the coke rate and tonnage figures, and (2), in the degree to which the top gas approaches the limiting ratio of CO/C02 for the reduction of iron oxide by CO gas. This ratio is shown in the equilibrium curve in Fig. I for the system Fe-O-C and CO2-CO-C. The closer the top gases approach this limiting ratio (set at 1.08 by Martin1 because of the effect of limestone calcination) the more efficiently we may expect a furnace to operate. The fact that low CO/C02 ratios parallel eficient operating performance caused us to investigate the cause of good or poor distribution and the effect of filling and other changes on furnace operation. Heretofore it has been possible to take a sample of furnace gas (usually from the dust catcher) and from it determine how closely the reducing gases were to the ideal or limiting value as set by the equilibrium diagram. However, to find just where in the top area the distribution was distorted and the top-gas CO/CO2 ratios were distant from equilibrium values has been a difficult and expensive investigational procedure. In an effort to overcome this difficulty, apparatus was designed to take gas samples and temperatures across the top radius of the furnace. It was hoped that with the aid of this apparatus traverse sampling of the ascending gases could be simplified, and the cost of sampling substantially lowered. Routine experimenting could then be maintained and results checked with furnace operation. It must be emphasized that a traverse sampling is necessary for a true picture, as single samples at any one point are unreliable. This statement can be verified by an examination of Tables 3 to 6, showing results obtained at our furnaces in a large number of tests. APPARATUS The design of the equipment for taking the samples was governed by the need for providing a simple, routine test that could be performed fairly quickly without adversely affecting normal furnace operation.

Jan 1, 1943

By T. E. Scott, R. P. Zerwekh

The charactevistics of the deformatiotz of fcc thorium were examined between 78 and 473 K. Activation energy, actiuation volume, and the temperature dependence of the flow stress were determined and conlpared uith several theories for the rate-controlling mechnnistn of the tempemture-dependent component of the flou~ stress. It was established that the Cottrell-Stokes law does not hold, even approximately, for thorium. Through consideration of the above factors and other parameters, it was concluded that the vandom solute barrier theory proposed by Friedel demonstrates the best agreement with experimental observations of the deformation of thorium below ambient temperature. THORIUM, the first metal in the actinide series of rare-earth elements, is interesting and important from two points of view. In the more practical vein, it is a potential reactor fuel. As such, it is important to know its properties. Of specific interest here are the mechanical properties of thorium. Second, no detailed information concerning the deformation characteristics of the actinide elements has been gathered to date. In view of the interesting physical and chemical properties of these metals, their mechanical behavior might reveal characteristics which could improve our understanding of the mechanisms controlling deformation of the more common metals. For example, it has been shown1 that thorium exhibits a yield point which is greatly enhanced by interstitial solute elements such as carbon. This is not a normal occurrence in fcc metals. The goal of this investigation, therefore, was to characterize the deformation of polycrystalline thorium. MATERIAL AND PROCEDURES Thorium, made by the magnesium intermediate alloy process described by Peterson et al.,2 was rolled and swaged to 0.065-in.-diam wire. The metal analysis is given in Table I. After preparation, the oxygen and nitrogen contents had risen to 308 and 60 ppm, respectively. The 0.065-in.-diam wires were cut into 2-in. lengths and annealed in a vacuum of lo-' Torr at 750°C for 1 hr, producing a grain size of 2735 grains per sq mm. The ends of the 2-in. sections were masked off so that a 1-in. gage length could be electropolished. Specimens were polished at 35 v in a solution of 6 pct perchloric acid in methanol which was maintained at 0°C . The gage diameters after polishing were about 0.0625 in. The tests were run on a screw-driven tensile machine at a constant crosshead speed corresponding to a strain rate of 0.005 min-'. The strain rate was changed rapidly after each 0.01-in. extension between 0.005 min-' and one of three higher strain rates which were selected in order to achieve strain-rate ratios of 5, 10, and 20. Tests were run at several temperatures from 78" to 473°K; most were tested at 423", 300°, 215", and 78°K. EXPERIMENTAL RESULTS Flow Stress vs Strain and Temperature. Typical true stress-true strain curves for thorium are shown in Fig. 1 for several temperatures over the range 473" to 78°K. The curves for 78", 215", 300") and 423°K were obtained from strain-rate change tests using the lower (0.005 min-') or base strain-rate values of stress. Additional tests, using the same base strain rate at different strain-rate ratios, gave curves which virtually superposed on those shown, indicating that strain-rate changes did not materially influence the work-hardening characteristics at the base strain rate. The curves for 273") 373") and 473°K were standard tensile tests at 0.005 min-'. The behavior of the flow stress with temperature is

Jan 1, 1968

By B. B. Zavoico

After showing continued and very satisfactory progress until the close of 1931, the oil industry of the Soviet, Union experienced very great difficulties, and since 1932 has not only failed to complete its assigned quotas but has fallen farther and farther behind them, and in fact during 1932 and 1933 Russian production has been below production in 1931. In 1934 the total crude oil production of 169,200,000 bbl. exceeded that of the former peak year, 1931, when 156,100,000 bbl. were produced. The production during 1934 amounted to 78.65 per cent of the plan. The failure to complete the plan has been due to the inability of the oil trusts to develop new fields; the fields that have been producing since 1917 still account for between 75 to 80 per cent of total production. The failure of the Soviet Government to develop new fields has been due to unsatisfactory organization of the geological work, to the extremely slow drilling of wells and their exploitation, and to the very much delayed development of the few areas that have been discovered. The official overestimation of the proven reserves of the country has undoubtedly been an important factor in giving the Soviet industry too much confidence when actually such reserves have been small. The official Soviet estimate of proven reserves of Russia is now placed at 21,000,000,000, bbl., while in fact such reserves, if estimated on a conservative basis, do not exceed 4,200,000,000 bbl., as will be shown later in this review. The refinery branch of the industry also showed unsatisfactory results with a recovery of gasoline, both straight-run and cracked, of only some 16 per cent of the total runs to stills. In fact, the showing of the refineries has been so unsatisfactory that the exports of gasoline have been greatly curtailed from 1933 to 1934, dropping to 10,000,000 bbl. in 1934 from 12,230,000 bbl. in 1933. With the indicated increase in domestic demand, together with but slightly increased refining capacity, the volume of available gasoline for export probably will be reduced to about 6,000,000 bbl. during 1935. The geographic distribution of constructed refineries has been unsatisfactory and the crude oils from Baku had to be transported by tankers

Jan 1, 1935

By R. H. Fillnow, D. J. Mac

IT has been demonstrated that alloys in systems structurally analogous to steel undergo reactions during heat treatment similar to those of steel, and yet very little work has been done on such systems, particularly from the standpoint of isothermal transformation. The literature shows that most of the isothermal work has been done on copper-alu-minum alloys.'-3 One paper has been reported on a eutectoid copper-silicon alloy,' and one on iron-nitrogen alloys.' There are no published reports of previous investigations on the isothermal transformation of a eutectoid beryllium bronze. At least two papers have been reported on isothermal age-hardening phenomena in beryllium-copper alloys of lower beryllium content.5,6 No information on eutectoid transformations in this alloy is given in Rimbach's book, "Beryllium." ' This paper reports the results of an investigation on the isothermal transformation characteristics of a eutectoid beryllium bronze. Materials Used and Procedure The eutectoid beryllium bronze used in this investigation was centrifugally cast at the Ampco Metal Co., Inc.. Milwaukee. Wis. A master beryl-lium-copier alloy, purchased from the Brush Beryllium Co., was used to make the beryllium addition to the copper. The alloy was melted under a protective carbon cover and Centrifugally cast into a graphite mold preheated to 920°F. Some trouble with segregation of beryllium in the melt was encountered but was eliminated by violent stirring during melting and pouring. Since very thin .specimens were used for the various heat treatments, only one casting of the four prepared was necessary for the complete isothermal study, thus eliminating any discrepancies caused by a change in composition. The analysis of this casting was 94.035 pct copper and 5.965 pct beryllium. A slight trace of iron was found. The castings were sawed into specimens approximately 3/32 in. in thickness. The specimens were first given an "austenitizing" heat treatment at 788°C, well within the single phase beta region, in a vertical tube furnace. The specimens were then quenched individually into an adjacent molten salt bath and held there for a definite time, after which they were quenched into water at room temperature. Temperature was held to ± 2°C in the salt bath. No homogenizing treatment was given the specimens other than the soak at 788°C. Despite the fact that this was a cast alloy, no evidence of segregation or coring was found in the microstructure of any specimen, either as cast or as heat-treated. Upon completion of the heat treatment, the speci-mens were subjected to metallographic examination

Jan 1, 1951

By J. H. Smith, H. W. Paxton

ALTHOUGH many structural and kinetic investigations have been made for alloys of iron and nickel, only meager data exist from thermodynamic investigations. The purpose of this note is to estimate the free energy of the Fe-Ni solid solutions from thermodynamic data available for ternary alloys containing iron and nickel. The lack of a description of the thermodynamic behavior for the Fe-Ni system has required the structural and kinetic analyses of the system to assume some form of solution behavior, usually regular, e.g., the mar-tensite transformation analysis of Kaufman and Cohen, 1 consistent with the limited thermodynamic data. Indications that this system could exhibit ideal solution departures might have been suggested by the large deviations from additivity rules observed in the density and lattice-parameter measurements of Jette and Foote2 who interpreted this in terms of possible solute-solvent interactions. Later Turkdogan et al. 3 and more recently Ward and wright 4 found a minimum in the graphite solubility in liquid Fe-Ni solutions near the concentration of FeNi3 with deviations from linearity persisting at all concentrations. This was interpreted by Ward and wright4 to indicate negative heats of solution and was suggestive of short-range ordering. The infinitely dilute activity coefficient of carbon (?oC) was also observed by smith5 to pass through a maximum near the FeNi3 concentration in Fe-Ni solid solutions. Recent investigations of the liquid solutions over the entire concentration range by Zellars et a1.' and Speiser et a1.," using vapor-pressure determinations, revealed both negative departures from Raoult's law and a nonregular solution behavior. The solid alloys have been studied by Oriani 8 and Kubaschew-ski and von Goldbeck6 employing gaseous H2/H2O equilibria with Fe and FeO. Both investigations were in substantial agreement, indicating very small departures from ideality. However, Oriani observed the formation of Fe3O4 (instead of FeO) at XFe= 0.441 which severed the equilibrium and precluded experimental investigation of the nickel-rich alloys. Heat-capacity and heat-content measurements have been evaluated by Montgomery10 and found generally unsatisfactory for gleaning thermodynamic information. This is due to the unknown final states of the alloys caused by the interference of the martensite transformation on cooling iron-rich concentrations and superlattice formation, magnetic transformation, and the varied heat treatments used by investigators of nickel-rich concentrations. As an alternative to the experimental difficulties, indirect estimates of the solid-solution behavior have been made by Fleischer and Elliott11 and Smith et a1.12 From their measurements of the solubility of Fe-Ni alloys in liquid lead, Fleischer and Elliott calculated the nickel activity (aNi) (and integrated for aFe) by assuming: 1) liquid lead has no solubility in solid Fe-Ni alloys, 2) Henry's law is obeyed throughout the liquid lead-rich phase (0— 12 at. pct Nil, and 3) Henry's law constant is independent of relative iron and nickel concentrations. The estimate of Smith et a1.12 was obtained

Jan 1, 1964

By H. W. Imholz

Active interest in the North Central Texas area centered in the development of the Palo Pinto limestone-producing zone, near the town of Avoca, in the northeast part of Jones County. This producing horizon was discovered in 1937, in the Iron Mountain Oil Company's well No. 1 Olander, in sec. 196, B.B.B. & C. survey, at 3238 to 3250 ft. During the development of this pool, it was generally referred to as the Avoca pool. As a second pool has been discovered in the same producing zone, also near the town of Avoca, the writer has taken the liberty of changing the name of the original Avoca pool to Avoca-Olander pool. Forty producers had been drilled in the Avoca-Olander pool by the end of 1938; their initial ranged from 28 to 300 bbl. per hour. Stimulus was given to the interest in the development of the Palo Pinto limestone when the Ungren-Frazier No. 1 Griffin, in sec. 199, B.B.B. & C. survey, Jones County, found the limestone from 3225 to 3250 ft., with an initial production of 931 bbl. per day. (This new pool has been given the name of Avoca-Griffin pool, by the writer.) The best well to be completed, up to the present time, is the Bert Fields No. 1 Taylor in sec. 199, B.B.B. & C. survey, which had an initial production of 748 bbl. in 3 hours. The Owen-Snebold No. 1 McKeever in sec. 158, B.B.B. & C. survey, in northwest Shackelford County, added to the interest in the Palo Pinto limestone when it extended the Ivy pool with a well in the Palo Pinto limestone from 3145 to 3183 ft., and was estimated good for 6,000,000 cu. ft. of gas and 6000 bbl. of oil per day. During 1938, Stonewall County obtained its first commercial producer when the Stonewall Oil Co. in No. 1 Parriott discovered the Palo Pinto limestone saturated from 5169 to 5176 ft. and tested 371 bbl. per day. Two new producing horizons were discovered about 2 miles east of the old Noddle Creek pool, Jones County; the first, the Humble Oil & Refining Co. No. 1 Irvin, in sec. 48, block 18, T. & P. R. R. Co. survey, which had saturated limestone from 2550 to 2567 ft. and was good for 100 bbl. per day; the second, in the Humble No. 1 Horton, sec. 40, which

Jan 1, 1939

By H. W. Imholz

Active interest in the North Central Texas area centered in the development of the Palo Pinto limestone-producing zone, near the town of Avoca, in the northeast part of Jones County. This producing horizon was discovered in 1937, in the Iron Mountain Oil Company's well No. 1 Olander, in sec. 196, B.B.B. & C. survey, at 3238 to 3250 ft. During the development of this pool, it was generally referred to as the Avoca pool. As a second pool has been discovered in the same producing zone, also near the town of Avoca, the writer has taken the liberty of changing the name of the original Avoca pool to Avoca-Olander pool. Forty producers had been drilled in the Avoca-Olander pool by the end of 1938; their initial ranged from 28 to 300 bbl. per hour. Stimulus was given to the interest in the development of the Palo Pinto limestone when the Ungren-Frazier No. 1 Griffin, in sec. 199, B.B.B. & C. survey, Jones County, found the limestone from 3225 to 3250 ft., with an initial production of 931 bbl. per day. (This new pool has been given the name of Avoca-Griffin pool, by the writer.) The best well to be completed, up to the present time, is the Bert Fields No. 1 Taylor in sec. 199, B.B.B. & C. survey, which had an initial production of 748 bbl. in 3 hours. The Owen-Snebold No. 1 McKeever in sec. 158, B.B.B. & C. survey, in northwest Shackelford County, added to the interest in the Palo Pinto limestone when it extended the Ivy pool with a well in the Palo Pinto limestone from 3145 to 3183 ft., and was estimated good for 6,000,000 cu. ft. of gas and 6000 bbl. of oil per day. During 1938, Stonewall County obtained its first commercial producer when the Stonewall Oil Co. in No. 1 Parriott discovered the Palo Pinto limestone saturated from 5169 to 5176 ft. and tested 371 bbl. per day. Two new producing horizons were discovered about 2 miles east of the old Noddle Creek pool, Jones County; the first, the Humble Oil & Refining Co. No. 1 Irvin, in sec. 48, block 18, T. & P. R. R. Co. survey, which had saturated limestone from 2550 to 2567 ft. and was good for 100 bbl. per day; the second, in the Humble No. 1 Horton, sec. 40, which

Jan 1, 1939

By A. S. Grove, C. T. Sah, E. H. Snow, B. E. Deal

A summary of- several recent investigations in to the properties of the metal-oxide-silicon system is presented. A major portion of these studies makes use of the MOS capacitance-z)oltage method of' analysis. The particular areas of investigation which are reported include: 1) a general survey of the electvical properties of thermally oxidized silicon surjbccs; 2) a study of ion migration through silicon dioxide films ; 3) measurements of electron and hole mobilities in surface inversion layers; 4) a study of impurity redistribution due to thermal o.ridatiotz; and 5) measurements of the rates of oxidation oj-heavily doper7. silicon. THE importance of the metal-oxide-semiconductor (MOS) system in the semiconductor industry is well-known. In addition to its importance in the "planar" device technology,' the MOS structure is now also used in the fabrication of active solid-state devices. Consequently, extensive efforts have been made recently to obtain a better understanding of the characteristics of this system. A summary of some studies of the MOS system conducted in our laboratories during the past year is presented. For the most part these studies used silicon as the semiconductor, along with silicon dioxide and aluminum as the other two components of the system. Since the MOS capacitance-voltage method of analysis was used extensively in these studies, we will first briefly describe its nature and consider some of the possible causes of deviation of experimental observations from the simple theory. We will then outline the various related areas of investigation carried out in our laboratories and will briefly indicate some of the results. It should be noted that the purpose of this paper is merely to provide a brief summary of MOS studies. More detailed discussions of the various areas of investigation are given in the references cited. PRINCIPLES OF THE MOS C-V METHOD OF ANALYSIS' A sketch of the MOS structure is shown in the upper portion of Fig. 1. In this case the insulating film is Si02 and the semiconductor p-type silicon. If a large negative bias is applied to the metal field plate, holes are attracted to the silicon surface. The silicon then behaves much like a metal and the capacitance measured is that of the oxide layer alone, Co. If a small positive bias is applied to the aluminum, holes are repelled and a region depleted of majority carriers is formed at the silicon surface. This depletion I-egion adds to the width of the dielectric and the measured capacitance begins to drop. With increasing positive bias, the width of the electrical depletion region increases. At some large positive bias an inzevsion regiotr is formed at the surface and additional charges induced in the silicon appear in the form of electrons in this narrow inversion region. Thus the depletion-region width approaches a maximum value and, consequently, the capacitance reaches a minimum value and then either levels off or rises again depending on the measurement frequency and the rate of equilibration of the minority carriers in the inversion layer.3 Band diagrams, along with the corresponding charge distributions, are shown in Fig. 1 for the above bias conditions. If minority carriers cannot accumulate at the surface to form an inversion region, the depletion-region width continues to increase with increased positive bias and the capacitance drops toward zero as in a reverse biased p-n junction. The effect of a work-function difference $hs between the metal and the silicon, and of surface charges per unit area Qss located at the oxide-silicon interface, is simply to attract charges in the silicon much like the applied bias. It can be shown that this results in a parallel shift of the capacitance-voltage characteristic along the voltage axis by an amount corresponding to AV = -$bIs + Qss/Co. Theoretical curves have been calculated4 giving the capacitance of the MOS structure C normalized to the oxide capacitance Co vs the quantity VG here VG is the voltage applied to the metal field plate. In Fig. 2 such calculations are shown as points for a particular oxide thickness and bulk impurity concentration for a p-type semiconductor. (For an n-type semiconductor the curves would be mirror images of these.) All three cases, i.e., low frequency. high frequency, and depletion, are indicated. Also shown in the figure are recorder tracings of the characteristics of actual devices. These characteristics have been shifted along the voltage axis to compensate the effect of surface charges and work-function difference. It is evident that agreement between experiment and theory is good. The nature of this shift along the voltage axis is

Jan 1, 1965

By E. Buehler, J. E. Kunzler

High-pu.1-ity molybdenum has been heat treated, melted, and zone refined and the physical and chemical changes that are produced by these processes have been studied by making resistance ratio measurements. Pronounced effects are observed that are associated with recrystalliza-tion at about 1200°C and with melting. Melting alone is found to result in a substantial purification by the evaporation of impurities such as iron. Zone refining is found to be reasonably effective with four passes producing a three-fold decrease in resistance ratio and a minimum ratio of 0.0003. With the aid of low temperature measurenzents, it has been shown that the build-up of a deposit of the material being zone refined on the radio frequency coil used for heating can lead to contamination of the sample. CONSIDERABLE interest in high-purity refractory metals for the study of mechanical properties has developed during recent years. Also the need for highly pure metals in certain fundamental studies, such as electronic band structure, has become quite widely appreciated. Molybdenum can now be produced with sufficiently high purity to make it attractive for such investigations. The most suitable measure of chemical purity of metals used for many of these studies is its resistance ratio, R,.,o,/Ro, During the purification of molybdenum by zone refining and its subsequent evaluation by this technique, a number of informative observations were made. These observations concern the effectiveness of zone refining, the volatilization of impurities at the melting point, and the recrystallization of molybdenum and appear to be pertinent to other refractory metals. Also, the usefulness of low-temperature resistance measurements as an analytical tool for evaluating the presence of chemical impurities and physical defects in metals is again illustrated. Samples of high-purity molybdenum of known mechanical history were heated to various temperatures between 800°c and their melting point. Resistance ratios of the samples were measured after they had been given a specified treatment. The data were used, along with mass spectrographic analysis, as an aid in interpreting the nature of the processes that occurred in conjunction with each treatment. Changes in the concentrations of chemical impurities and physical defects are typical of things that effect the low-temperature resistivity. SAMPLES The starting material was obtained from Westing-house Corp., Bloomfield, N.J. It was in the form of molybdenum rods, usually 1/8 or 3/16 in. in diameter. These had been previously processed from bars, 5/8 in, in diameter, originally reduced from 4 in. diam arc-cast ingots, by hot swaging at about 1300°c. In the final step, the temperature was lowered to about l lOO°C which resulted in the production of elongated grains. Typical grains were about 0.03 mm thick and 0.6 mm long. The molybdenum was quite pure as is indicated by the results of mass spectro-scopic analysis1 given in Column 2 of Table I. Other nongaseous elements not listed in the table were not detected. ZONE REFINING AND THERMAL TREATMENT OF SAMPLES Several sample rods, 8 to 10 in. long, were zone refined or were heat treated at several temperatures. Both types of operations were performed using 3 me-

Jan 1, 1962