Search Documents

By R. N. Dokken, J. F. Elliott

A high-temperature solution calorimeter was used to measure directly the partial molar heat of mixing of nickel in the Cu-Ni system, 0 to 15 at. pct Ni and 1200°C; of silver in the Cu-Ag system, 0 to 50 at. pct Ag and 1100°C; and of cobalt in the Cu-Co system, 0 to 6 at. pct Co and 1200°C. The heats of fusion of copper and silver were also detervnined directly. The results of these investigations are as follows: Cu-Ni: HM = [2.64 + 0.25Xm JXNiXCy kcal/g-U~OI Cu-Ag: HM =[4.00 + 0.31XAglXAgXCu kcal/g-atom Cu-Co: HF~ = [8- 5X~,]X& kcal/g-atotn Cu, AH, = 3290 * 275 cal/g-atom Ag, AH, = 2890 * 250 cal/g-atom The performance of the calorimeter was enhanced by improving the operational and control procedures, particularly the temperature-wieasuren~ent method and the solute-addition practice. The interpretation of the experimental data was improved by developing machine computational techniques that increased the speed, flexibility, and accuracy of the treatment of the data. THIS paper reports further measurements of the heats of solution of liquid metals with the high-tem- perature solution ca1orimeter.l Measurements were made of the partial molar heats of mixing in the following liquid alloys: Cu-Ni, Cu-Ag, and Cu-Co. In addition the heats of fusion of copper and silver were also determined. The apparatus and the experimental procedure were essentially those of Benz and Elliott.2 Several modifications in the experimental method and the means for interpreting the data were incorporated in this study to improve the results. The operation of the calorimeter and its characteristics will be described only briefly here. The

Jan 1, 1965

By R. M. Rose, D. P. Ferriss, J. Wulff

Single crystals of tantalum, tungsten, and the binary alloys thereof were grown by electron-beam zone melting and tested in tension between 77° and 373°K. The ductile-to-brittle transition temperature increased sharply with solute concentration, for both tungsten-rich and tantalum-rich alloys; apparently, the maximum transition temperature exists near the 50 pet concentration. Twinning was observed to be a consequence of cleavage-crack propagation. Cleavage occurred on(100)planes, and extensive tearing and "river markings" were present. The onset of brittleness could not be associated with any change in deformation mode, the yield point phenomenon, or the large rise in yield stress with decreasing temperature. Cleavage was observed to initiate at either the specimen surface, or subgrain boundaries. The observation was made that the grain boundaries of Polycrystalline materials are probably even better as nucleation sites for fracture, and are responsible for brittleness at high temperatures and lower solute concentrations than those of the corresponding single crystals. TUNGSTEN and tantalum, the two high-melting neighbors in the third transition period of the periodic table, present striking contrasts. Although both are bee, tungsten has far higher elastic moduli, and the highest ductile-to-brittle transition (DBT) of all the pure metals.' Tantalum, however, is ductile at liquid helium temperatures. Large strain aging and yield point phenomena are observed in tantalum,2,3 but only to a lesser extent in tungsten.4 Tungsten work-hardens at a high rate,5 whereas this effect is negligible in tantalum.' Since the mutual solid solubility of these two metals is complete,7 and no ordering has yet been reported in the binary system, the possibility of depressing tungsten's DBT by tantalum additions was considered. Also, tungsten additions to tantalum could produce hard, high-melting alloys which might be ductile at room temperature. Such alloys offered excellent bases for complex alloy development, particularly with regard to the effect of rhenium on Group VI metals.8"10 In addition, there was the opportunity to examine flow and fracture modes in the vicinity of the DBT, with particular emphasis on the correlation between brittleness and fundamental deformation mechanisms. Myers11 has reported that recrystallized alloys with up to 10 pet W in tantalum are ductile at room temperature, but alloys with 20 pct W could not be swaged at temperatures as high as 500°C. The whole spectrum of Ta-W alloys has been surveyed by Braun, Sedlatschek, and Kiefferl2 using sintered powder compacts. In addition to some physical properties they reported a maximum hardness at about 50 at. pet W, dropping to much lower hardness levels for the pure components. They were able to cold work tantalum-base alloys with as much as 30 pet W and to warm work tungsten-base alloys with up to 20 pet Ta by procedures similar to those used for pure tungsten. EXPERIMENTAL In order to study deformation modes and to keep the impurity concentrations at a minimum, electron-beam zone melting was used to prepare single crystals of high purity. The electron-beam zone melting apparatus is similar to that described by Calverley, Davis, and ever" and incorporates a grid control rectifier to maintain control of emission current. Pure metals were refined by making three zone passes at 4 mm per min up the rod. Alloys were prepared by melting together wire of one constituent on a previously melted rod of the major constituent. Subsequently, two zone passes were made in opposite directions to level the composition after the manner suggested by pfann.14 Purification of the starting materials was accomplished by evaporation of the several impurities, and the degree to which this was accomplished is indicated in the chemical analyses of Table I. The uniformity of composition along a zone levelled rod was within the i 1 pet accuracy of the fluorescent X-ray technique used to determine composition. Crystallographic orientation of the

Jan 1, 1962

By L. S. Darken

Measurements of the electrical conductivity, the thermal electromotive force, and the deviation from stoichiometry by thermogravimetry were made on ferrous oxide (wüstite) single crystals as well as on poly-crystalline samples in the temperature range of -900" to 1330°C. In the region defined by T 2 1000°C and 1.05 5 O/Fe 5 1.10 the electrical conductivity was shown to be proportional to the sixth root of- the oxygen partial pressure and to be linearly dependent on the deviation from stoichiometry. The absolute Seebeck coefficient of single and polycrystalline wüstite was shown to be independent of temperature in the above region and a p to n transition of the Seebeck coefficient was observed at O/Fe = 1.09 in polycrystalline wüstite. Analysis of the results showed that the predominant defects in wüstite in the above region were doubly ionized cation vacancies. The analysis also ruled out the existence of complexes of the type postulated by Roth, except that below 1000°C there is some evidence of 'association of defects. Of the three oxides of iron (FeO, Fe3O4, Fe2O3) only FeO (wüstite) can exist within a wide range of the ratio O/Fe. This has been shown by several investigations of the phase diagram using for instance chemical analysis of quenched samples'-4 or thermogravimetric measurements. 5,8 Darken and Gurry's1 data for example in the temper- ature range 1100o to 1400°C show that the lowest O/Fe ratio obtainable for FeOl +. is about 1.045 and that the existence range extends to O/Fe = 1.20 at 1400oC. On the basis of detailed analysis of thermogravimetric measurements made by Vallet and Raccah6 the existence of three varieties of wüstite at elevated temperatures was suggested by these authors and by Kleman. It is well-established that wüstite has a NaCl structure with vacant cation sites.3, 8 From a neutron-diffraction study of wüstite samples quenched to room temperature Roth9 concluded that defects in wüstite are mostly complexes composed of two cation vacancies and one interstitial cation in a tetrahedral site. The atomic arrangement in the vicinity of such a defect is similar to that in magnetite, where each occupied tetrahedral site is surrounded by four vacant octahedral positions disposed at the corners of a tetrahedron, so arranged that each vacancy is shared by two tetrahedral cations. Thus there is an average of two vacancies per interstitial. Recent X-ray diffraction measurements made by Smuts10 on quenched wüstite samples confirmed the results of Roth's neutron-diffraction experiments. Roth's model of defects in FeO can be regarded as a solid solution of Fe3O4 in FeO; salmon1' used this defect model to calculate the activity of Fe3O1 in FeO at high temperature and claimed good agreement with the results obtained experimentally by Darken and Gurry.' Each missing cation in wüstite is accompanied by two trivalent cations, thus preserving charge neutrality. The "holes" which differentiate between the Fe 2+ and Fe3' states of the ions in octahedral positions can overcome the attractive field of the cation vacancies, and are then free to move through the crystal as charge carriers. A similar picture holds for COO, NiO, andMnO.l2, 13 Localization of the charge carriers in transition

Jan 1, 1968

By D. S. Tannhauser, I. Bransky

Measurements of the electrical conductivity, the thermal electromotive force, and the deviation from stoichiometry by thermogravimetry were made on ferrous oxide (wüstite) single crystals as well as on poly-crystalline samples in the temperature range of -900" to 1330°C. In the region defined by T 2 1000°C and 1.05 5 O/Fe 5 1.10 the electrical conductivity was shown to be proportional to the sixth root of- the oxygen partial pressure and to be linearly dependent on the deviation from stoichiometry. The absolute Seebeck coefficient of single and polycrystalline wüstite was shown to be independent of temperature in the above region and a p to n transition of the Seebeck coefficient was observed at O/Fe = 1.09 in polycrystalline wüstite. Analysis of the results showed that the predominant defects in wüstite in the above region were doubly ionized cation vacancies. The analysis also ruled out the existence of complexes of the type postulated by Roth, except that below 1000°C there is some evidence of 'association of defects. Of the three oxides of iron (FeO, Fe3O4, Fe2O3) only FeO (wüstite) can exist within a wide range of the ratio O/Fe. This has been shown by several investigations of the phase diagram using for instance chemical analysis of quenched samples'-4 or thermogravimetric measurements. 5,8 Darken and Gurry's1 data for example in the temper- ature range 1100o to 1400°C show that the lowest O/Fe ratio obtainable for FeOl +. is about 1.045 and that the existence range extends to O/Fe = 1.20 at 1400oC. On the basis of detailed analysis of thermogravimetric measurements made by Vallet and Raccah6 the existence of three varieties of wüstite at elevated temperatures was suggested by these authors and by Kleman. It is well-established that wüstite has a NaCl structure with vacant cation sites.3, 8 From a neutron-diffraction study of wüstite samples quenched to room temperature Roth9 concluded that defects in wüstite are mostly complexes composed of two cation vacancies and one interstitial cation in a tetrahedral site. The atomic arrangement in the vicinity of such a defect is similar to that in magnetite, where each occupied tetrahedral site is surrounded by four vacant octahedral positions disposed at the corners of a tetrahedron, so arranged that each vacancy is shared by two tetrahedral cations. Thus there is an average of two vacancies per interstitial. Recent X-ray diffraction measurements made by Smuts10 on quenched wüstite samples confirmed the results of Roth's neutron-diffraction experiments. Roth's model of defects in FeO can be regarded as a solid solution of Fe3O4 in FeO; salmon1' used this defect model to calculate the activity of Fe3O1 in FeO at high temperature and claimed good agreement with the results obtained experimentally by Darken and Gurry.' Each missing cation in wüstite is accompanied by two trivalent cations, thus preserving charge neutrality. The "holes" which differentiate between the Fe 2+ and Fe3' states of the ions in octahedral positions can overcome the attractive field of the cation vacancies, and are then free to move through the crystal as charge carriers. A similar picture holds for COO, NiO, andMnO.l2, 13 Localization of the charge carriers in transition

Jan 1, 1968

By Robert Y. Grant

This study outlines the history of metal mining in Japan and the characteristics of the industry as they existed from 1925 to 1945. Mining and milling operations are described together with the role of the Japanese Government. A description of post-hostilities conditions and the present state of the industry is included. MANY of Japan's larger and better known mines date back to the early centuries of the Christian Era. The first stimulus to mining in Japan came through the growth of Buddhism, A. D. 600 to 700, and the attendant need for copper and other metals for temple ornaments and statues. During the Feudal period, 1333 to 1568, mine operations were expanded to meet the demand for ornament metal and for financing of campaigns. After removal of the seat of government from Kyoto to Tokyo, about 1600, the Tokugawa Shogunate placed great emphasis on mining, and many new mines were opened, some of which are still operating. Toward the end of the Tokugawa period, mining had declined sharply from its earlier peak. The easily worked, high grade portions of the orebodies had been exhausted, and the mining techniques then available could not exploit the deeper, lower grade ores. Similarly, extraction of metal from the sulphide ores presented a major problem. With the Meiji Restoration in 1868 and the rapid opening of the country to western ideas came a rejuvenation of the mining industry. Mining, milling, and smelting processes were greatly improved, resulting in the extension of development work into hitherto inaccessible portions of orebodies. The demand for metal during World War I stimulated activity throughout the industry; copper mining, particularly, expanded to a point where Japan ranked second among world producers.* During the depression following the war, mining underwent a severe contraction in activity, recovering slowly during the late 1920's only to undergo a further setback in the worldwide depression which started in 1929. Mineral output declined in 1930, but the beginning of Japanese expansion, 1931 to 1932, brought about an increase in the output of mine products starting between 1932 to 1934. Production continued to rise, the peak output being attained 1939 to 1943 in virtually all commodities. The greatest production of iron ore, chromite, and manganese was not experienced until 1944 when blocked imports, coupled with strong demands for steel, provided the needed incentive. Through necessity, Japan produced much of her mineral needs from her own mines at high cost during World War 11. Taking the 1932 to 1936 period as an average, however, Japanese mines produced only 16 pct of the iron available to industry, 8 pct of the lead, 33 pct of the zinc, and 68 pct of the copper. Nearly all of Japan's output of gold, silver, copper, lead, and zinc between 1925 and 1945 came from 30 to 49 pct of the mines for which production data are available; for example, 66 of 174 gold-silver mines accounted for 98 pct of the output of this group. Further analysis of mine output indicates that a large part of Japan's metal output was derived from a few large mines; about 10 gold-silver, 15 copper, 3 lead-zinc, 5 manganese, and 2 iron mines account for most of the production. Many of these mines have been operated for 200 to 400 years. With the

Jan 1, 1952

By P. Chaudhari, Michael B. Bever

The heat of solution at infinite dilution of selenium in bismuth, the heat of mixing of selenium and bismuth, and the limit of solubility of selenium in bis~rzuth have been determined at 573, 623; and 663°K by metal solution calorimetry. The heat of forrrzation of the compound Bi2Se at these temperatures has been determined from the heat effects associated with the precipitation of the compound from a saturated solution oj selenium and bismuth. The published information on the thermodynamic properties of the system Bi-Se is limited. The heat of solution at infinite dilution of selenium in bismuth at 623°K has been measured.' The heat of formation at 273 K1 and room temperature2 and the heat capacity at 80 K3 of the compound Bi2Se3 have been reported. An estimate of the heat of formation of the compound BiSe at room temperature has been published.2 Information on the phase relations in the system Bi-Se is available.' In the investigation reported here the following quantities have been determined at 573", 623", and 663°K: 1) the heat of solution at infinite dilution of selenium in bismuth, 2) the heat of mixing of selenium and bismuth in bismuth-rich solutions, 3) the limit of solubility of selenium in bismuth, and 4) the heat of formation of the compound BizSe. These quantities were determined by the addition of selenium to bismuth-rich solutions in a metal solution calorimeter. The determination of the heat of formation at the tem- perature of the calorimeter bath involved the precipitation of the compound from a saturated solution in the calorimeter. 5,6 This method differs from that commonly used which requires the addition of the compound and of a mechanical mixture of its components and yields the heat of formation at the temperature from which the additions are made (273 K EXPERIMENTAL PROCEDURE AND CALCULATIONS The solution calorimeter has been described in detail.' Pure bismuth (99.999+ pct) was used as the bath at the start of a run. The calorimeter was calibrated with small amounts of bismuth added from 273°K; the differences of the heat contents of bismuth at 273°K and the temperatures of the baths are listed in Table I. After the calibration, additions of hexagonal selenium (99.999+ pct) were made. Loss of selenium by evaporation was negligible. No unusual experimental difficulties were encountered.9 The differences in the heat contents10 of selenium at 273°K and the temperature of the bath, listed in Table I, were subtracted from the measured heat effects to give the "adjusted heat effects". The methods by which the heat of solution at infinite dilution, the

Jan 1, 1968

By E. T. Hayes, A. H. Roberson, M. H. Davies

R. F. Dornagala and D. J. McPherson (Armour Research Foundation, Chicago)—I should like to compliment the authors for a workmanlike job in determining the partial phase diagram of a system comprised of two rnetals which are certainly not easy to work with. We are completing work at Armour Research Foundation on an Atomic Energy Commission-sponsored project for the determination of eight zirconium binary diagrams. Work on the Zr-Cr system has been completed and should be published within the next year. For our work, Westinghouse Grade 3 iodide crystal bar served as the zirconium melting stock. Johnson-Matthey, electrolytic chromium, specially treated for oxygen removal, was employed. The overall constitution of the system determined at Armour Research Foundation is in very good agreement with the present work. We found a eutectic at 18 pct Cr and 1280 °C, somewhat lower than the value reported. This temperature was confirmed by thermal analysis, incipient melting studies, and regular isothermal anneals. The eutectoid was located close to 1 pct Cr and 835°C by metallographic analysis of annealed specimens. Maximum solubility of chromium in /S zirconium was 4.5 pct at the eutectic temperature. Chromium solubility in a zirconium was less than 0.28 pct at all temperatures. We found the compound at 53 pct to melt around 1700°C, with an open maximum, but determined its crystal structure to be hexagonal close-packed (MgZn, type). The lattice parameters were in excellent agreement with those determined by Wallbaum in 1942. The diagrams are in substantial agreement, and .part of the differences are undoubtedly due to the use of different zirconium melting stock. M. K. McQuillan (Birmingham, England)—I read this paper with a great deal of interest, as it covered the same field as some work of my own.' There are a number of points in the present paper on which I would like to comment. First, I should say that I, too, used zirconium prepared by magnesium reduction of the tetrachloride and electrolytically prepared chromium, and melted the alloys in a Kroll-type arc furnace. The purity of my alloys should, therefore, be comparable with the purity of those of the present authors, and any differences in our observations would not be expected to be attributable to this cause. The differences between my observations and theirs concern the presence of the eutectic, the temperature of the eutectoid, and the melting point of the compound. I would be very much interested in any further evidence the authors may have for the occurrence of the eutectic at 1380°C. During the course of my work I noted that a number of my alloys containing 60 to 90 pct Zr melted at about 1400 °C, and for a time assumed that a eutectic occurred at this temperature as described in the paper. On further investigation, however, I found that the structures of the as-melted alloys could not be made to fit in with this interpretation of the system. If a eutectic exists in this region of the system it would be expected that the as-melted alloys would show the usual type of cast structure, i.e., dendrites of the compound plus eutectic. This, however, does not occur, as may be seen from Fig. 9. The compound seen there is not dendritic in form, and the remaining material is by no means certainly eutectic. It may be argued that a compound such as ZrCrl would not form dendrites but would tend to crystallize in geometric shapes. In this case, however, I have evidence to the contrary, as on the chromium side of the compound, where a eutectic occurs at about 1545"C, the compound formed from the liquid takes on a conventional dendritic form, and the eutectic is observed in the interdendritic spaces in the usual way. There is no reason to suppose that the compound would behave differently in an alloy lying on the zirconium side of the compound composition if a eutectic existed there too.

Jan 1, 1953

By J. C. Yannopoulos, N. J. Themelis

Ah electronic thermogravirnetric balance was used to measure the veductioiz rule o single cirpric oxide particles suspended in a stream of hydrogen. Very jzne thermocouples embedded in lie center and at the surface of the sphere recorded the variation of terw perature during reduction. In contrast to iron oxide reduction, where in most instances the rate of interface reactiokl is controlling, the heat- and mass-transfer phenotnena play a predolrinant role in the reduction of cupric oxide. The correlation of experitnental data or tnass lransfev lhrough the boundary layer at Reynolds nunlber 0-4 50 was as jollocs: ThE reduction of cupric oxide by hydrogen is represented by the equation: It is a highly exothermic reaction and the amount of heat released varies only slightly with temperature (-21,430 cal per g-mole at 400°C). Most of the published studies on this system have been conducted at temperatures in the range of 34 to 280c.l-&apos; The concensus of opinion has been that at temperatures below 200°C the reaction is preceded by an induction period during which there is very little or no reduction. The length of this period diminishes as the temperature of the reaction is increased1l5 and aseawa found that at 280°C reduction starts practically immediately when the oxide is exposed to hydrogen gas. The existence of an induction, or incubation, period has led experimenters to believe that the reduction of CuO by hydrogen is catalyzed by metallic copper.&apos; Boldurev and rmolaev found that mechanical additions of powdered copper to oxide did not affect its reduction, although metallic copper produced during the reduction seemed to have a catalytic effect. At least three other authors2&apos;5&apos;7 have reported that addition of copper had no effect on the rate of reduction. Pease and alor&apos; observed that water vapor had a strong inhibiting effect on the reduction at 1503C, but its effect was greatly diminished at 200 C. Pavlychenko and Rubinchik5 studied this reaction at 159 to 235 C and found that, once the reaction had been initiated, there was no inhibiting effect due to the introduction of water in the hydrogen stream; at temperatures above 183°C there was no inhibiting effect due to water vapor, either before or during reaction. The same authors noted that the rate of reduction was independent of pressure in the range of 200 to 700 mm Hg. aseawa investigated the kinetics of the CuO-Hz system at 160 to 280°C and estimated the apparent activation energy at 14,000 cal per g-mole. A similar value (13,500 1200 cal per g-mole) was reported by ond&apos; in the temperature range 148 to 216°C. Bond also reported that there was no incubation period and that water vapor had no inhibiting effect on reduction at temperatures above 190 C. The above studies have been conducted at temperatures below 280°C and the physical configuration of the system under investigation has not been defined adequately. However, it is well-known that the mechanism of gas-solid reactions depends on a number of in series physical and chemical rate prcesses.&apos;&apos; It is, therefore, essential to include among the experimental factors the geometry of the solid system and the mass-transport characteristics of the reducing gas. Scott studied the reduction of packed beds of cupric oxide cylinders by Hz-He streams of very low hydrogen concentrations at temperatures 400 to 600 C, pressure of 10 to 30 atm, and gas velocity from 0.18 to 5.8 ft per sec (3 < Rep < 30). The reduction rate was found to be mainly controlled by diffusion through the boundary layer and through the pores of the reduced copper phase. The following correlation was proposed: Scott in an earlier work studied the reduction of fixed beds of cupric oxide wire and found that the rate of flow of the gas stream through the bed had a controlling effect on the rate of reduction. The same mass-transfer phenomenon was observed by Bond and clark13 on a similar reduction system. The analogy between mass and heat transfer through the boundary layer which exists between a solid surface and the bulk stream stems from the similarity of the differential equations representing these phenomena

Jan 1, 1967

By G. G. Hancock, H. H. Johnson

Hydrogen gas at atmospheric pressure is shown to cause substantial embrittlement in a martettsitic high-stretzgth steel. Subcritical crack growth is observed at very lom stresses and with high growth rates. It is suggested that an adsorbed layer of hydrogen atoms at the crack-tip surface provides the damaging hydrogen. Oxygen in small quantity, as little as O.7 pct by volume, is shown to eliminate subcritical crack growth in gas environments caused by hydrogen or water vapor. However, dissolved oxygen in water has little or no influence upon crack-growth rates. Oxygen-stopped cracks may be restarted by water, or by hydvogen or water vapor if oxygen is removed from the environment. These observations are interpreted in terms of preferential adsorption of oxygen at the crack tip and the formation of an oxide barrier. RECENT investigations1-3 have demonstrated that environmental factors are frequently responsible for delayed failure in martensitic high-strength steels. The environment causes crack initiation from preexisting cracklike flaws at unexpectedly low stresses, often far below the uniaxial yield strength. The crack then propagates at a rate controlled by the environment and the crack-tip stress-field intensity; during this period crack propagation will cease if either the stress or the aggressive environment is removed, and this may be considered a definition of subcritical crack growth. Fracture occurs when the crack has grown to a critical length, such that the fracture toughness of the steel is exceeded. Several liquids are known to cause delayed failure, but water and water vapor are the most severely damaging of the environments investigated to date.&apos;-3 It has been suggested that hydrogen produced during corrosion reactions may be the actual embrittling agent2 The severe embrittlement caused by water vapor inevitably raises the question as to whether other gas environments are damaging. Previous work4&apos;5 has demonstrated that high-pressure hydrogen (2250 psi or greater) is an effective embrittling medium, as measured by such criteria as reduction in area, notch tensile strength, and time to failure. Moreover, the embrittlement was eliminated by the addition of small quantities of air or oxygen to the high-pressure hydrogen, but it was not influenced by additions of nitrogen or argon.4 In the present study attention is focused upon gas environments at atmospheric pressure, in particular hydrogen and oxygen. The influence of these constituents upon the initiation and growth of a crack from a pre-existing cracklike flaw in a high-strength steel was determined directly by the electric-potential method of monitoring crack growth. MATERIALS AND PROCEDURE The H-11 steel was supplied by the U.S. Naval Research Laboratory as 3 by 12 by 0.065 in. sheet specimens with 1-in. transverse center slots. The slot tips were finished by Elox machining to a radius of 0.001 in. or less. The yield strength was 230,000 psi; chemical composition and heat-treatment schedule are given in Table I. The experimental apparatus, precracking procedure, and incremental loading sequence have been described previously.3 In the only significant change, precracking was sometimes carried out by a hydrogen embrittlement and baking technique. All experiments were conducted at room temperature; the hydrogen gas environment was purified by a commercial palladium purifier. Crack initiation and propagation were followed by the electric-potential method,&apos;-3 using a calibration that has been recently dicussed. Stress-field intensities at the crack tip were computed by the conventional Irwin frmula; the plasticity correction was negligible and therefore not included. EXPERIMENTAL RESULTS A striking brittleness associated with molecular hydrogen at atmospheric pressure is demonstrated by the data in Table I1 and Fig. 1, which indicate that subcritical cracks in hydrogen initiate at lower stress-field intensities and propagate more rapidly than in fully humid argon. Ki and Kf are the crack-tip stress-field intensities at initiation and termination of subcritical crack growth, respectively. Termination, of course, corresponds to fracture. In both hydrogen and humid argon Ki is less than Kf

Jan 1, 1967

By D. H. Shaffer, W. F. Harris, W. M. Hickam, M. H. Loeffler

Experiments have been performed on the quantitative addition to niobium of enriched isotopes 018 and 017 at the 0.1 - 40 micro-gram level and their subsequent recovery. A measured quantity of molecular oxygen of known isotopic concentration is added to niobium metal by oxidation. Recovery of the enriched isotopes as carbon monoxide is by the vacuum fusion technique. Quantitative determinations of the enriched isotopes are made in standard volumes at constant temperature using accurately calibrated micromanometers and the mass spectrometer as pressure measuring instruments. THE presence of low concentrations of nonmetallic impurities in metals can often adversely affect the physical properties of the metal. The increase in hardness and the embrittlement of refractory metals due to oxygen is well known. In metallurgical studies dealing with the diffusion rates or the effect of oxygen on the physical properties of refractory metals, it is often necessary to add small quantities of oxygen to the metal and later recover the total quantity present. It is desirable, therefore, to establish the accuracy with which microgram quantities of oxygen can be added to niobium and recovered by vacuum fusion. The successful addition of microgram quantities of oxygen to metals by the usual manometric techniques and the subsequent recovery by vacuum fusion is difficult because of the uncertainty in the accurate determination of the quantity of oxygen originally present in the metal and because of the chance of contamination by atmospheric oxygen. In order to minimize these uncertainties earlier workers have added quantities of O16 at levels much higher than the oxygen concentrations that are of interest.&apos;-3 In order to eliminate the uncertainty associated with the O16 additions to metals at low microgram levels, experiments have been performed on the quantitative addition of oxygen highly enriched in O17 and O18 at the 0.1 to 40 pg level to niobium and the subsequent quantitative recovery of the isotopes by vacuum fusion. Since the natural abundance of O17 is 0.04 pct and of 0" is 0.2 pct this enriched oxygen provides a uniqueness from interference not achieved in earlier work.&apos;-= A measured quantity of molecular oxygen of known isotopic concentration is diffused into the metal. Recovery of the isotopes in the form of carbon monoxide is by vacuum fusion. The total quantity of gas is determined in standard volumes at constant tempera- ture using accurately calibrated Consolidated Electrodynamics micromanometers and the mass spectrometer for pressure measurements. The molecular and isotopic composition is determined mass spectrometrically. APPARATUS A schematic of the oxygen addition apparatus is shown in Fig. 1. Take-offs are provided for the attachment of the isotope container and for sample bulbs which are used to transfer samples to the mass spectrometer. Metal valves are used throughout the system including the sample bulbs in order to achieve a vacuum of 10"6 mm Hg. Evacuation is accomplished with a 3-stage oil-diffusion pump backed by a mechanical pump. A liquid nitrogen trap is used to remove condensables and to prevent oil vapor from entering the system. A micromano-meter is used for pressure measurements. The furnace assembly is shown in Fig. 2. It consists of a quartz tube joined to the apparatus through a 40/W joint with Apiezon W low-pressure wax. The furnace cap, also a 40/W pyrex joint, is provided with a pyrex hook. The sample is suspended from this hook with a platinum wire. The total volume of the furnace section is 435 ml. All volumes were determined by expanding a known volume of gas at a known pressure into the evacuated system and re-measuring the pressure. Both the micromanometer used on the oxygen addition system and the micromanometer used on the mass spectrometer were compared to a precision

Jan 1, 1961

By W. Vickers

Single-point rotating cantilever fatigue tests have been carried out at 550" to 650°C on beryllium produced by a variety of fabrication routes. All the specimens gave similar plots of stress against number of cycles to failure but failure occurred at a lower stress range in the hot-pressed material than in the extruded material. A discontinuity or "kink" appears to exist in the curves and this is considered. A true endurance limit was not evident up to 10 cycles. When Brush hot-pressed warm-extruded beryllium was tested at 600oC a relationship where Nf = number of cycles to failure, ?ep = plastic strain range, and c = constant, was shown to be applicable for values of ?ep > 6.3 x 10-4. Further for this moterial and temperature and for frequencies between 150 and 4500 cycles per min, the variation of number of cycles to failure with frequency obeyed the expression N = Af0.44 where N =number of cycles to failure, f = frequency, and A = constant. Examination of the fracture surfaces indicated that they were generally intergranular and in all cases the higher the stress the more irregular was the fracture. Microexamination has shown that grain boundary cavities and fine intergranular cracks were associated with the fractures. REVERSING or cyclic stresses set up in fuel elements can lead to failure by fatigue. Fatigue stresses may be developed by instability of the fuel element in the coolant flow leading to rattling against the channel wall or fin vibration. Thermal cycling also sets up reversing stresses due to differential expansion of fuel and can. Fatigue resistance is of some importance therefore in the evaluation of canning materials. At the time the work described in this paper was initiated, beryllium was being considered for the can and endcaps of an advanced gas-cooled reactor fuel element. With this in mind, beryllium obtained from different manufacturing routes was tested on single-point rotating cantilever fatigue machines at temperatures the same as those envisaged in the reactor to obtain appropriate fatigue data. The results obtained indicated a discontinuity in the S-N curves coinciding with the yield stress in the specimens. Although in some cases the data is insufficient to warrant a detailed quantitative analysis, a qualitative analysis of this effect was thought to be justified. 1) EXPERIMENTAL DETAILS The materials used are given in Table I together with the production route and available analyses. The specimen shape is shown in Fig. 1. The fatigue specimens were machined slightly oversize, after which they were given a stress-relieving anneal of 1 hr at &apos;750° C in vacuum. This was followed by an etch in sulfuric-phosphoric-chromic acid mixture down to the finished dimensions given in Fig. 1. Etching served to remove the interference colored oxide film formed on the surface during annealing and very small recrystallized surface grains too. The specimen was mounted in the grips of a cantilever machine and rotated inside a furnace controlled at the testing temperature. The specimen was loaded in increments as the speed was increased until the required load was applied at 5000 cycles per min. A revolution counter was used to record the total number of cycles.

Jan 1, 1964

By Joseph G. Franzone, Alan K. Kuhn, Jerry J. Oliver

INTRODUCTION Tailings produced by many uranium milling operations consist of fine sands with some silt and slimes. When fine sandy materials are placed by hydraulic methods behind an impermeable dam, they are deposited in a loose state and some portion remains saturated. These saturated, loose fine sands are highly susceptible to liquefaction, the phenomenon in which a monotonic or cyclic disturbance causes excess pore water pressure and, concurrently, a total loss of strength in the sand. Once liquefied, the fine sand flows, causing collapse of supported structures. The potential for such a liquefaction failure was identified and successfully treated at Sohio Western Mining Company&apos;s L-Bar Uranium Operations near Seboyeta, New Mexico. The Sohio tailings dam is an earthfill starter dam with tailings raises constructed upstream of the starter dam crest. Beginning with the start of mill operations in 1976, tailings were deposited hydraulically in the impoundment behind the starter dam. As the tailings level approached the crest of the starter dam, beached tailings were excavated and placed in lifts by a dozer to form two raises above the crest of the starter dam. As the impoundment has gradually filled with tailings, the decant water pond level has risen. Correspondingly, the water level in the tailings dam, upstream of the chimney drain, has also risen. By August 1980, the phreatic surface was above the crest of the starter dam and stability analyses indicated that the tailings dam did not have the safety factor of 1.0, under static loading with liquefaction, implicit in the 1980 New Mexico State Engineer&apos;s requirements. The problem related directly to the high phreatic surface in the loose sandy tailings behind a dam structure that was not capable of resisting failure which might develop in liquefied tailings. Two methods of stability enhancement were considered for the Sohio dam. One method was reinforcement of the dam using a clay buttress placed against the downstream slope. The other method was installation of horizontal drains through the starter dam to drain decant water and lower the phreatic surface. Either method would increase the stability of the dam. However, the comparative analysis of the methods indicated that horizontal drainage offered significant advantages in cost and could provide a more direct remedy of the source of the problem, the saturated section of tailings. In addition, a drainage system would be more amenable to modification and more quickly installed than a buttress. On the other hand, a clay buttress could be more directly controlled, would involve routine earthwork, and has successful precedent. Therefore, the buttress approach would involve less risk. After weighing the advantages of both methods and the costs versus risks, the horizontal drainage approach was selected. Consequently, a horizontal pipe drain system was recommended and designed (D’Appolonia, 1981a). This paper describes the design and installation of the drainage system and its initial performance. PIPE DRAIN SYSTEM DESIGN Design Criteria and Parameters To increase the stability of the dam to acceptable levels, the drainage system had to lower the phreatic surface behind the dam to the level calculated to give a minimum safety factor of 1.0 under conditions of liquefaction. In addition, the system needed to be essentially self-operating, easy to maintain, and economical. To accomplish these objectives, the following design criteria were established: 1. The pipe drains must lower the phreatic surface at least 4.3 m (14 ft.) at the midpoint along the dam (the deepest section) and by proportionately smaller amounts toward the abutments to satisfy safety factor requirements.

Jan 1, 1982

By R. A. Wattenbarger, H. J. Ramey

A systematic study has been made of the application of the real gas pseudo-pressure m(p) to short-time gas well testing. The m(p) function can be used in real gas flow problems to account for the variation of viscosity and z-factor with pressure. A mathematical model was solved numerically to generate solutions of various real gas flow problems. The effects of turbulence, formation damage and wellbore storage were included in the model. The analysis of simulated well tests showed that the interpretation methods normally used for liquid flow are generally accurate when the m(p) is used. For practical rates without turbulence, the solutions are not rate-sensifive, and the flow capacity.. kh and skin effect can be determined accurately from either a buildup or a drawdown test. However, the kh calculated from a drawdown test can be significantly low when turbulence is present. A case was simulated in which this error wa.s 36 percent. Turbulence does not affect the determination of kh from buildup tests. The proper determination of kh from p and pa buildup and drawdown plots is developed by analyzing their relationship to the m(p) method. A simple equation is given that can be used for long-range gas well performance forecasting. This expression is compared with a method pre-sended by Russell et al." Introduction The formation flow capacity and wellbore damage condition can be determined for liquid-producing tests by means of buildup and drawdown tests. These tests make use of short-time pressure transient data rather than stabilized flow tests that are often used for gas well testing. Tracy&apos; presented a method of gas well testing that was based on ideal gas equations and utilized p2 buildup plots. This method was shown to be good for low pressure wells. MatthewsZ suggested plotting p and using an average slope and average gas properties. This method was more successful on high pressure wells. Al-Hussainy, Ramey and Crawfordh howed that variation in gas properties could be simplified by using the real gas pseu do-pressure m(p). Some cases showed that the use of the m(p) function Original manuscript received in Society of Petroleum Engineers office Aug. 8. 1967. Revised manuscript received June 11, 1968. Paper (SPE 1835) was presented at SPE 42nd Annual Fall Meeting held in Houston Tex., Oct. 1-4. 1967, and at SPE 4th Annual Eastern Regional ~eetin$ held in Pittsburgh. Pa., Nov. 2-3. 1967. 0 Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. &apos;References given at end of paper. provided an accurate method of interpreting buildup and drawdown tests. Because the work of Al-Hussainy et al. included only a few actual cases, there was a need to explore the use of the m(p) method for a greater variety of flow conditions. The occurrence of turbulent flow around the wellbore often is an important factor in gas well testing. Swift and Kiel,&apos; and Carter et a1.&apos; treated turbulence in gas well testing, but did not consider the variation of viscosity and z-factor with pressure. This paper presents the results of an investigation of the application of the m(p) method to buildup and drawdown testing. Vhe investigation included the effects of turbulence, formation damage and wellbore storage. Gas Flow Equations To formulate the mathematical model, many of the assumptions usually used in well testing theory are applied. The system has radial geometry with a closed outer boundary and is composed of a horizontal porous formation that has uniform and isotropic rock properties and uniform thickness. Allowance is made, however, for a radial region of reduced permeability near the wellbore. This region represents formation damage. The geometry of the system is shown in Fig. 1. Darcy&apos;s law does not always apply to gas flow. A more general expression is needed for non-Darcy, or "turbulent" REGION OF DAMAGED PERMEABILITY SEALED BOUNDARIES ClRCULAR WELL BORE Fig. 1—Radial flow model. AUGUST, BT7

Jan 1, 1969

By T. J. Bosworth

The effect of hydrogen pretreatment of alumina, magnesia, and zirconia crucibles on reduced oxygen levels in iron charges has been studied. Hydrogen treatment of commercial high-purity magnesia crucibles was observed to produce as high as 70 pct reduction in oxygen content in iron melts. Hydrogen treatment of the commercial high-purity grade zirconia crucibles produced a 25 pct reduction in oxygen levels in iron melts. An average reduction of Knoop hardness of 47 pct was recorded on the iron charges melted in hydrogen-treated crucibles. On the basis of the experiments and the free-energy diagram, it appears that the major source of reducible oxygen to the iron charge is the suboxides and impurity oxides rather than the major oxide of the crucible. Suitable pretreatment of the crucibles to reduce and remove these oxides yields low oxygen levels in iron melted in the crucibles. DURING the last decade, attempts to produce more pure and uniform alloyed metals have brought about the development of many new melting techniques. Notable among these are vacuum-induction melting, inert and consumable-electrode melting, the cold-mold technique, and numerous techniques for removal of impurities by chemical reaction. However great the achievements in this field, metals must still be melted in contact with media of varying reactivity; i.e., gas, ceramic, and slag. Studies have been made to attain an understanding of the reactions that take place during melting, including slag-metal reactions and equilibria, equilibrium of hydrogen and water vapor, and carbon dioxide and carbon monoxide with oxygen in molten iron. These reactions have been treated quite thoroughly. There is one condition, however, that has been widely overlooked, and, to the author&apos;s knowledge, only cursive investigation has been made of it. This is the reaction between the ceramic crucible material and the iron charge. In recent years, Hadley and Bianchi&apos; made a series of studies on hydrogen deoxidation of iron in magnesia crucibles. Bianchi2 studied crucible-FeO equilibria in the temperature range 1525°to 1650°C in high vacuum with, however, inconsistent results. Richardson and Jeffes3 in their series of articles on thermodynamic reactions in the making of iron and steel refer to Wentrup and Hieber&apos;s4 work on iron and aluminum deoxidation. Their pork included melting iron in alumina crucibles and measuring the aluminum and oxygen content in the iron. Because of the low values obtained, question has arisen of their analytical accuracy.3 Dastur and chipman5 obtained values on hydrogen-oxygen equilibrium in molten iron contained in alumina crucibles similar to those obtained in experiments in the present program. Hochmann6 studied removal of impurities in chromium irons in high vacuum. His results with respect to oxygen level in chromium-iron melted in magnesia crucibles are consistent with results we have obtained.

Jan 1, 1959

By William Hurst, A. F. van Everdingen

For several years the authors have felt the need for a source from which reservoir engineers could obtain fundamental theory and data on the flow of fluids through permeable media in the unsteady state. The data on the unsteady state flow are composed of solutions of the equation Two sets of solutions of this equation are developed, namely. for "the constant terminal pressure case" and "the constant terminal rate case." In the constant terminal pressure case the pressure at the terminal boundary is lowered by unity at zero time, kept constant thereafter, and the cumulative amount of fluid flowing across the boundary is computed, as a function of the time. In the constant terminal rate case a unit rate of production is made to flow across the terminal boundary (from time zero onward) and the ensuing pressure drop is computed as a function of the time. Considerable effort has been made to compile complete tables from which curves can be constructed for the constant terminal pressure and constant terminal rate cases, both for finite and infinite reservoirs. These curves can be employed to reproduce the effect of any pressure or rate history encountered in practice. Most of the information is obtained by the help of the Laplace transformations, which proved to be extremely helpful for analyzing the problems encountered in fluid flow. The application of this method simplifies the more tedious mathematical analyses employed in the past. With the help of Laplace transformations some original developments were obtained (and presented) which could not have been easily foreseen by the earlier methods. INTRODUCTION This paper represents a compilation of the work done over the past few years on the flow of fluid in porous media. It concerns itself primarily with the transient conditions prevailing in oil reservoirs during the time they are produced. The study is limited to conditions where the flow of fluid obeys the diffusivity equation. Multiple-phase fluid flow has not been considered. A previous publication by Hurst&apos; shows that when the pressure history of a reservoir is known, this information can be used to calculate the water influx, an essential term in the material balance equation. An example is offered in the literature by Old² in the study of the Jones Sand, Schuler Field, Arkansas. The present paper contains extensive tabulated data (from which work curves can be constructed), which data are derived by a more rigorous treatment of the subject matter than available in an earlier publication.&apos; The application of this information will enable those concerned with the analysis of the behavior of a reservoir to obtain quantitatively correct expressions for the amount of water that has flowed into the reservoirs, thereby satisfying all the terms that appear in the material balance equation. This work is likewise applicable to the flow of fluid to a well whenever the flow conditions are such that the diffusivity equation is obeyed. DIFFUSITY EQUATION The most commonly encountered flow system is radial flow toward the well bore or field. The volume of fluid which flows per unit of time through each unit area of sand is expressed by Darcy&apos;s equation as where K is the permeability, the viscosity and aP/ar the pressure gradient at the radial distance r. A material balance on a concentric element AB, expresses the net fluid traversing the surfaces A and B, which must equal the fluid lost from within the element. Thus, if the density of the fluid is expressed by p, then the weight of fluid per unit time and per unit sand thickness, flowing past Surface A, the surface nearest the well bore, is given as The weight of fluid flowing past Surface B, an infinitesimal distance 6r, removed from Surface A, is expressed as

Jan 1, 1949

By A. F. van Everdingen, William Hurst

For several years the authors have felt the need for a source from which reservoir engineers could obtain fundamental theory and data on the flow of fluids through permeable media in the unsteady state. The data on the unsteady state flow are composed of solutions of the equation Two sets of solutions of this equation are developed, namely. for "the constant terminal pressure case" and "the constant terminal rate case." In the constant terminal pressure case the pressure at the terminal boundary is lowered by unity at zero time, kept constant thereafter, and the cumulative amount of fluid flowing across the boundary is computed, as a function of the time. In the constant terminal rate case a unit rate of production is made to flow across the terminal boundary (from time zero onward) and the ensuing pressure drop is computed as a function of the time. Considerable effort has been made to compile complete tables from which curves can be constructed for the constant terminal pressure and constant terminal rate cases, both for finite and infinite reservoirs. These curves can be employed to reproduce the effect of any pressure or rate history encountered in practice. Most of the information is obtained by the help of the Laplace transformations, which proved to be extremely helpful for analyzing the problems encountered in fluid flow. The application of this method simplifies the more tedious mathematical analyses employed in the past. With the help of Laplace transformations some original developments were obtained (and presented) which could not have been easily foreseen by the earlier methods. INTRODUCTION This paper represents a compilation of the work done over the past few years on the flow of fluid in porous media. It concerns itself primarily with the transient conditions prevailing in oil reservoirs during the time they are produced. The study is limited to conditions where the flow of fluid obeys the diffusivity equation. Multiple-phase fluid flow has not been considered. A previous publication by Hurst&apos; shows that when the pressure history of a reservoir is known, this information can be used to calculate the water influx, an essential term in the material balance equation. An example is offered in the literature by Old² in the study of the Jones Sand, Schuler Field, Arkansas. The present paper contains extensive tabulated data (from which work curves can be constructed), which data are derived by a more rigorous treatment of the subject matter than available in an earlier publication.&apos; The application of this information will enable those concerned with the analysis of the behavior of a reservoir to obtain quantitatively correct expressions for the amount of water that has flowed into the reservoirs, thereby satisfying all the terms that appear in the material balance equation. This work is likewise applicable to the flow of fluid to a well whenever the flow conditions are such that the diffusivity equation is obeyed. DIFFUSITY EQUATION The most commonly encountered flow system is radial flow toward the well bore or field. The volume of fluid which flows per unit of time through each unit area of sand is expressed by Darcy&apos;s equation as where K is the permeability, the viscosity and aP/ar the pressure gradient at the radial distance r. A material balance on a concentric element AB, expresses the net fluid traversing the surfaces A and B, which must equal the fluid lost from within the element. Thus, if the density of the fluid is expressed by p, then the weight of fluid per unit time and per unit sand thickness, flowing past Surface A, the surface nearest the well bore, is given as The weight of fluid flowing past Surface B, an infinitesimal distance 6r, removed from Surface A, is expressed as

Jan 1, 1949

By K. P. Gupta

In ternary systems containing silicon and transition elements, silicon was found to stabilize the a phase.1 At 1000°C a broad a-phase region was found in the Cr-Mn-Si system,1 which extends very close to the Mn-Si binary line (within about 3 at. pct Cr). Later investigation showed that, if chromium was replaced by small amounts (3 to 5 at. pct) of v,1 Ti, Nb, Ta, Mo, or w,1 the a phase or the R phase was again stabilized. Whether stabilization of complex crystal structures is possible by small additions of iron, cobalt, or nickel to Mn-Si is not known. Investigation of the Co-Mn-Si system4 shows the presence of several ternary phases, but at cobalt concentrations higher than 10 at. pct. In the present work the ternary systems Fe-Mn-Si and Co-Mn-Si were investigated at low iron and cobalt concentrations (< 7 at. pct Fe or Co) in search of phases of complex crystal structure. Experimental Procedure. The alloys were pre-pared by induction melting Co (99.8 pct), Si (99.9 pct), electrolytic Fe (99.88 pct), and Mn (99.9 pct) in recrystallized alumina crucibles under an inert atmosphere of argon gas. The alloy specimens were wrapped in molybdenum foil, sealed in argon-filled (at 1/2 atm) silica capsules and annealed for 72 hr at 1000" 1°C, and water-quenched. The use of argon-filled capsules was found to reduce the losses during annealing and the molybdenum foil prevented reaction of the manganese with silica. The total weight loss due to annealing and melting was found to be less than 1 pct for each alloy. The alloys were not analyzed chemically. A part of each annealed specimen was polished and examined metal-lographically using etching solutions, a) 0.1 to 0.5 pct oxalic acid solution in water, or b) 0.5 pct HNOs in methyl alcohol. Even though the etching solutions were quite dilute, the specimens were heavily etched and stained if the etching time exceeded more than 5 sec. Etching times found suitable were usually 1 to 3 sec. For X-ray diffraction work, a part of each annealed specimen was powdered by crushing after the exposed surface was ground off. X-ray diffraction patterns were taken with powder specimens using a 20-cm-diam asymmetrical focusing camera and Fe K radiation. These powder patterns were found quite satisfactory for the purpose of phase identification. However, X-ray diffraction patterns of single-phase alloy powder specimens were also taken using a Siemens diffractometer and filtered Cr-Ka radiation for greater resolution of the diffraction lines. Results and Discussion. In the Fe-Mn-Si system a new ternary phase was found at 1000°C between the p manganese and the MnsSi phase regions. The approximate phase relationships in this region of the 1000°C isothermal section are shown in Fig. 1. The new ternary phase, designated as the K phase, was found to occupy a narrow region about 1 at. pct in width and extending from Fee.oMn74.5Silg.5 to Fe.Mn.Silg.. At the high-iron content region, the K phase was found in equilibrium with the p manganese and the MnsSi phases but, at the low-iron content end of the K-phase region, the phases in equilibrium with the K phase were the p manganese phase, the MnsSi phase, and another new phase, designated in Fig. 1 as the v phase. The v

Jan 1, 1964

By L. W. Holm, G. G. Bernard

Laboratory experiments were conducted to determine the effect of foam on gas flow in porous media. Previous studies have indicated that foam may be applicable as a restrictive agent in influencing underground gas flow. Foam was found to be exceedingly effective in reducing the permeability of porous media to gas. Consolidated and unconsolidated sands with specific permeabilities of 100 to 146,000 md had, in the presence of foam, gas permeabilities that were less than 1 per cent of the specific permeability; in many cases the gas permeability was practically zero. Foam reduced the gas permeability of loose sand to a much greater degree than that of a tight sand. For example, the permeability of a 125,000-md sand was reduced to 3 md while the permeability of a 4,000-md sand was reduced to 7 md. This effect should cause, to some degree, selective plugging of high permeability channels in various oil displacement processes. The presence of oil in a porous medium decreased the effectiveness of foam in reducing gas permeability; apparently oil acts as a foam depressant. However, it was found that certain foaming agents were very effective in reducing permeability even. in the presence of oil. Also, continuous injection of other foaming agents increased their effectiveness, when oil was present. The effect of foam on permeability of porous media to gas was studied as a function of foaming agent concentration and injection rate, absolute permeability, total pressure, pressure gadient, length of porous system, brine concentration and time. INTRODUCTION The use of surface active agents in flood water to increase the recovery of oil has been studied in the laboratory and in the field for decades, with rather limited success. In recent years a new approach to the problem was proposed. Instead of using an aqueous solution of surfactant as an oil recovery agent, Bond and Holbrook2 proposed that the oil recovery agent be a mixture of surfactant solution and gas. In their method, a water-soluble surface active agent with foam-producing characteristics is injected into an underground formation as an aqueous slug. This slug is followed by gas to produce a foam within the rock. Foams are defined as "agglomerations of gas bubbles separated from each other by thin liquid films&apos;! A foam is fundamentally an unstable system. The foam process for oil recovery has since been studied by other investigators. Fried 1 has shown that foam can displace from porous structures oil that normally is unrecoverable by conventional water or gas drives. This superior oil displacing action is believed to be the result of several factors: (1) foam introduces into the reservoir many resilient interfaces of various sizes and curvatures, which increase the probability that a proper combination of forces for oil displacement will be created; (2) foam has appreciable viscosity which improves mobility ratio and contact efficiency; (3) foam accentuates the trapped gas effect because high gas saturations are possible without producing high gas/oil ratios. Deming4 studied the effect of various foam properties on the displacement of liquid. He found that (1) high foaming ability favors high displacement efficiency; (2) high foam stability is not necessary for high displacement efficiency; (3) displacement efficiency decreases with increase in plasticity of foam and (4) displacement efficiency is unaffected by surface tension of foaming agent solution. One of the important aspects of this oil recovery process is the effect of foam on gas permeability. The simultaneous flow of gas and liquid in porous media has been studied by numerous investigators and a large amount of literature exists on the subject. In this previous work, gas and liquid have generally been considered as essentially independent phases, whose flow characteristics are related through the saturation parameter. Foam, however, is a material with properties that are considerably different from those of its components; for example, the viscosity of a foam is greater than either of its components. Gas flow in a porous medium in the presence of foam should be considerably different

Jan 1, 1965

By J. S. Kennedy, G. L. Simard, A. A. Lefrew, C. M. Judson, R. B. Booth

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from these laboratories.&apos;* These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pct Zn for ZnS); and the quartz from Klondike, Mo., analyzed as 99.97 pct SiO,. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from SS supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1953

By J. S. Kennedy, A. A. Lefrew, C. M. Judson, R. B. Booth, G. L. Simard

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from these laboratories.&apos;* These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pct Zn for ZnS); and the quartz from Klondike, Mo., analyzed as 99.97 pct SiO,. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from SS supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1953