Search Documents

By M. D. Hassiallis

The claim is made in a number of patents1'2'3'4 that some compounds of the class known as aryl sulphides have collector properties. One of these patents generalizes the claim to include all aryl sulphides, whose generic formula is R-S2-R' (where x = 1,2, . . . ), with the restriction that if the aromatic radicals R, R' contain substituent groups these groups may not contain nitrogen or oxygen. Moses, Hess, and Perkins cite as evidence for their claims the results of flotation tests on Anaconda and Miami copper ores using diphenyl sulphide, ditolyl disulphide and dinapthyl disul-phide as collectors. The use of alkyl sulphides as collectors has also been reported5 with the conclusion that the alkyl sulphides are better collectors than the corresponding aryl sulphides. The experimental work cited appears to confirm this contention. In order to test these claims with respect to diphenyl sulphide, a sample, purchased from the Eastman Kodak Co., was tested against Anaconda ore. The procedure followed. was that of Moses, Hess, and Perkins. A sample of ore weighing 500 • grams was placed in a laboratory ball mill. To this was added 220 grams of water, 0.06 grams of commercial diphenyl sulphide (1/4 lb. per ton of ore), and 0.8 grams of lime (3 lb. per ton of ore). The material was ground until 93 per cent passed a 65-mesh screen. This pulp was diluted to 16 per cent solids. A sample of the diluted pulp was placed in a Minerals Separation type of laboratory flotation cell. After a a-min. agitation period, pine oil was added and the froth collected for a period of 15 min. This test recovered 68 per cent of the copper, with a ratio of concentration of 6.8:I. The tailing assay was 0.3 per cent Cu. Moses, Hess and Perkins attained a recovery of 75 per cent, with a ratio concentration of I2:I. Although these results do not compare too well with those of Moses, Hess and Perkins, subsequent tests showed an improvement, as judged by vanning of the tails. It is concluded, therefore, that the patent results are confirmed. Contact-angle Tests In order to study the response of the various minerals, found in Anaconda ore, to commercial diphenyl sulphide, some contact-angle tests were made. Polished particles of bornite, chalcodte, chalco-pyrite, pyrite and quartz were conditioned for 15 min. in a suspension of diphenyl sulphide in water. The concentration of this suspension was 0.284 grams per liter, this being the concentration of this reagent in the ball mill. The conditioned particles were rinsed with water (not rubbed with filter paper or boiled linen) and then tested against an air bubble in the bubble machine, with the following results: born-

Jan 1, 1943

By J. S. Aronofsky, J. P. Heller

This paper presents a mathematical analysis of the fluid mixing which occurs during flow through porous media. The analysis is based on the well-known diffusion equation with mass transfer term. It is pointed out that the use of this equation is justified by a single general assumption which does not specify any particular mechanism for the mixing process. Formulas are given for tracer fluid concentrations for two different boundary and initial conditions. Calculated numerical values compare closely with some published results of experiments in which no viscosity or density difference existed between displaced and displacing fluids. INTRODUCTION A phenomenological theory of the mixing and diffusion process is presented for the flow in a porous medium of two miscible liquids of equal viscosity and density. This is based on the classical diffusion equation which has been used to explain such processes as Brownian motion and heat conduction. More recently, this same differential equation has been derived (in a manner analogous to the work in this paper) for the problem of heat transfer during fluid flow in porous media.' The purpose of this paper is to show that the available experimental evidence justifies the use of this simple diffusion equation. The recent data of Koch and Slobod' and of von Rosenberg' are used to test this diffusion model by comparing concentration curve shapes and calculating "effective diffusion coefficients". The same differential equation for miscible displacement, as well as some experimental confirmation, has been published in Japan by K. Yuhara,4 and recently in this country by Day.5 Yuhara arrives at his con-clusions through analogy with turbulent diffusion, de- scribing the microscopic velocities in terms of "eddy motion" — although unlike the ordinary eddies of hydraulics. Day proceeds directly from Scheidegger's6 concept of the dispersion of velocities. After a very clear description of Scheidegger's theory, he applies it to calculate the motion first of a drop and then of a thin layer of brine into a bed of sand. For the latter case, Day derives and solves the same differential equation as Eq. 1. In our presentation no detailed assumptions are made as to the mechanism of displacement. In fact, several microscopic processes may well be involved—the only general assumption made is that their cumulative microscopic effect may be described by the addition of a second-order term to the differentirl equation of continuity. DERIVATION OF EQUATIONS Let us consider the displacement in one spatial dimension of Liquid A from a sample of porous media by Liquid B. A and B are assumed completely miscible and of the same viscosity and density. Both fluids are also assumed to be incompressible and it is specified that the total flow is the same for any cross section. It is evident that the rate at which Liquid B would be carried across such a section would be given by the product of the fluid velocity, u, and the concentration, C, of B in the fluid mixture assuming the constancy of u and C over the cross section. Since the volume of Fluid B is conserved, this leads to the one-way wave equation - u ?C/?x = ? ?C/?l where x increases in the direction of u—the "Darcy velocity", Q/A (or velocity flux per unit area), and 9 is the fractional porosity. Consider the case where fluid B is displacing Fluid A and the concentration distribution is represented by a step funcLon (with a vertical discontinuity). The solution of Eq. 1 predicts no mixing

Jan 1, 1958

By R. T. Keyes, R. B. Clay, L. L. Udy, V. O. Cook, M. A. Cook

Based on compressibility and stress wave velocity in rock, initial explosive loading conditions, the thermochemistry of the explosive and reasonable description of the pressure-distance relations behind the shock front, the distribution of energy between the products of detonation and the burden are estimated as a function of time for various loading conditions. These include 'powder factor', loading density A (fraction of borehole occupied by explosive), and the explosive itself. Factors responsible for rock fragmentation are discussed in terms of: 1) 'release wave fracturing', 2) 'shear wave fracturing', and 3) 'release of loading fracturing' or 'rock bursting'. Release wave fracturing appears to occur only in the immediate vicinity of free faces, and shear wave fracturing only adjacent to the borehole under normal blasting conditions. Rock bursting is thus considered to be the most important means of rock fracturing in blasting. Means for maximizing it are considered. The most important factors to consider include maximum available energy A, explosive density p1, loading density A and 'powder factor'. Maximum efficiency is attained in general by maximizing the A . p1 product. This is achieved by using high density explosives at a loading density of unity (A = 1.0). Ways for achieving this condition are discussed. The bulk-handled aluminized slurry blasting agents have the desired properties for achieving optimum conditions for high blasting efficiency based on the theory outlined herein. Factors considered most important in the blasting of rock are: 1) The maximum available energy A, determined by the heat of explosion Q and the mechanical efficiency ?, a factor intimately associated with the mode of application (A = Q at highest gas concentrations). 2) The 'borehole pressure', pb, or the maximum pressure developed in the borehole after passage of the detonation wave and before the burden has had time to move or become compressed appreciably. (Owing to the short duration of the detonation wave at any particular point in the borehole, the fact that the explosive may not always fill the borehole completely and the further fact that the burden may not actually see the detonation pressure, the borehole pressure is considered more significant than the detonation pressure p2 as a performance factor in borehole blasting.) The borehole pressure is determined by the explosion or adiabatic pressure, p3 , and the loading density, A, or the fraction of the borehole filled by explosive. 3) The physical conditions important in the application of the explosive are: a) The 'powder factor,' (We/Wr), or the ratio of the wt of the explosive to that of the rock being blasted expressed as lb per ton or more generally in lb/cu yd. b) The bulk density, p1 ?. c) The 'burden' or 'line of least resistance,' the spacing between boreholes, the geometry of the borehole pattern and sequence of firing. d) The physical and chemical properties of the rock, most significant of which are possible heterogeneties, such as faulting, prefracture, and greater than micro-scale chemical heterogeneities. (This factor is not considered here but deserves a great deal of careful consideration.) All of these factors need to be carefully considered in the most economical engineering of a blast. Here is considered firstly an outline of the present status of dynamic rock mechanics, particularly as it pertains to blasting. The factors pertaining to the most efficient application of blasting agents are also considered, followed by a discussion of methods of application to achieve optimum explosives performance. ROCK MECHANICS Dynamic rock mechanics is currently a rapidly developing science contributing greatly to a better understanding and consequently the more effective application of explosives in blasting of rock.1-22 Basic to the development of the science of dynamic rock mechanics were the advances of Goransen23 and the Los Alamos and NOL groups24-28 concerning rock and stress wave phenomena and the transmission and reflection characteristics of stress waves at interfaces between different media. Basing considerations on this new knowledge as well as new experimental methods of study (ultra-high speed streak and framing cameras and electronic timers) the theory of fracture and failure of solids under impulsive loading by stress waves developed rapidly.14,16,27-29 Also the

Jan 1, 1967

EARLY this year the Board of Directors announced that, through the generous gift of past-president W. L. Saunders, a gold medal to be awarded for distinguished achievement in mining had been estab-lished. At the December meeting of the Board the medal committee reported that it recommended that the first medal be awarded to David William Brunton for "development and exposition of the principles and prac-tice of ore sampling; for systematic daily mapping of mine geology; for the Brunton mining compass; and for engineering achievements in connection with great tunnels." The formal presentation of the medal will be at the din-ner, on Feb. 16, in connec-tion with the annual meet-ing. Mr. Brunton, like several other prominent Institute members, was born in Can-ada, and came to the United States when he was twenty-four years old. He had then been in civil en-gineering work for three years and after a year more of it, deciding that mining was more attrac-tive he spent two years at the University of Michigan doing advanced work in geology a n d chemistry. His first mining engage-ment was with the Dakota and San Juan Mining Co., at Mineral Point, Ouray County, Colo. That was in June, 1875, and the young engineer had to travel 230 miles by trail from the then nearest railroad station at Pueblo. Having to come out because the company did not get in enough supplies to last through the winter he became metallurgist for the Hunt, Douglas & Stewart Co., at Georgetown, Colo. When the Hunt and Douglas plant proved a success, H. A. Taylor, the father of Mr. Brunton's later partner, Frank M. Taylor, engaged him to build the Clear Creek Reduction Works. Eighteen months later he built the Native Silver Mining Co. mill at Caribou and a year later a mill at Silver Peak, Nev., that was so successful that the principal owner shut it down to freeze out the minority stockholders. The winter of 1879 found him at Leadville where he did engineering work for the Robert E. Lee, Duncan, Wolftone, A. Y. & Minnie, and Dinero mines, eventually becoming manager of the Colonel Sellers. In 1886 he was called in on apex-side-line litigation at Aspen with the result that he went there to develop the mines for economic and legal pur-poses, and later became the manager of three of them. His most notable piece of work there was the driving of

Jan 2, 1927

By John Mathews

IT is twenty years since the writer made his first molybdenum steels and others were making them commercially five years earlier but the prevailing opinion seems to be that molybdenum steels are new; from time to time the daily press speaks of important discoveries in Europe and intimates that American steel makers have much to learn in regard to alloy steels. The earlier experiments were largely confined to the use of relatively high percentages of molybdenum in tool steels and permanent magnet steels. Recent developments deal with the types of alloy structural steels used for airplane, automobile, and other engineering requirements; in these, the molybdenum content is usually less than 1 per cent. The earlier types generally have been unsuccessful commercially, but the newer types of steels are becoming of increasing importance. The war showed our dependence on foreign sources for alloying metals; molybdenum alone is widely distributed in the United States and seemingly abundant. Many deposits are not now of commercial interest, owing to location and relatively small amount of ore available, but other deposits are being developed and a stable source of supply seems well assured. In tool and magnet steels, it was early found that 1 part of molybdenum was equivalent to from 2 to 2.5 parts of tungsten. The permanent magnet steels investigated by Madame Curie,1 in 1898, contained from 3.36 to 4.05 per cent. molybdenum; in 1902, Dr. E. L. French and the writer thoroughly tested steels containing from 2:0 to 4.0 per cent. These steels gave satisfactory tests for permanence, but were low in residual density and much more sensitive to hardening than the corresponding tungsten products. We discontinued work with them, therefore, and have no advice that such steels have been used commercially here or abroad.

Jan 2, 1921

By M. D. Hassialis

THE claim is made in a number of patents1,2,3,4 that some compounds of the class known as aryl sulphides have collector properties. One of these patents generalizes the claim to include all aryl sulphides, whose generic formula is R-S¬R[=]-R’ (where x = r,2, . . . ), with the restriction that if the aromatic radicals R, R' contain substituent groups these groups may not contain nitrogen or oxygen. Moses, Hess, and Perkins cite as evidence for their claims the results of flotation tests on Anaconda and Miami copper ores using Biphenyl sulphide, ditolyl disulphide and dinapthyl disulphide as collectors. The use of alkyl sulphides as collectors has also been reported5 with the conclusion that the alkyl sulphides are better collectors than the corresponding aryl sulphides. The experimental work cited appears to confirm this contention. In order to test these claims with respect to diphenyl sulphide, a sample, purchased from the Eastman Kodak Co., was tested against Anaconda ore. The procedure followed was that of Moses, Hess, and Perkins. A sample of ore weighing 500 grams was placed in a laboratory ball mill. To this was added 220 grams of water, 0.06 grams of commercial diphenyl sulphide (1/4 lb. per ton of ore), and 0.8 grams of lime (3 lb. per ton of ore). The material was ground until 93 per cent passed a 65mesh screen. This pulp was diluted to 16 per cent solids. A sample of the diluted pulp was placed in a Minerals Separation type of laboratory flotation cell. After a 2-min. agitation period, pine oil was added and the froth collected for a period of 15 min. This test recovered 68 per cent of the copper, with a ratio of concentration of 6.8: 1. The tailing assay was 0.3 per cent Cu. Moses, Hess and Perkins attained a recovery of 75 per cent, with a ratio concentration of 12: 1. Although these results do not compare too well with those of Moses, Hess and Perkins, subsequent tests showed an improvement, as judged by vanning of the tails. It is concluded, therefore, that the patent results are confirmed. CONTACT-ANGLE TESTS In order to study the response of the various minerals, found in Anaconda ore, to commercial diphenyl sulphide, some contact-angle tests were made. Polished particles of bornite, chalcocite, chalcopyrite, pyrite and quartz were conditioned for 15 min. in a suspension of diphenyl sulphide in water. The concentration of this suspension was 0.284 grams per liter, this being the concentration of this reagent in the ball mill. The conditioned particles were rinsed with water (not rubbed with filter paper or boiled linen) and then tested against an air bubble in the bubble machine, with the following results: born-

Jan 1, 1943

C. A. HANSEN (communicated appendix*).-Since the above paper was written, tests have been conducted with a view to securing a sounder basis for discussing the effects of temperature on the behavior of the zinc cell. The following data, while making no pretense to great accuracy, are still reasonably close. Cells were operated with the same feed solutions, but at varying temperatures, the latter being controlled by means of immersed steam coils. Current efficiencies obtained indicate that the corrosion rate

Jan 11, 1918

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by plotting [So = ooT as a function of eo =o] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors? It was shown that the true physical behavior of the material in the tension test could best be represented by plotting the average true stress, [S = P] as a function of [e = q' = log A-le = log Lo] where P, A, L, S, [e], and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941

By Walter E. Duncan

THE ores treated at the concentrating plant largely come from the blanket replacement deposits of the northeastern part of Hardin County, Illinois, and consist of complex mixtures of galena, sphalerite and fluorspar in a gangue of quartz, limestone and sandstone. The several minerals are so intimately intergrown that they are not liberated at the sizes usually treated by gravity concentration in the usual fluorspar plant. For this reason, an all-flotation method of concentration was developed in cooperation with the station of the U. S. Bureau of Mines at Rolla, Mo.1 This flotation separation made possible the commercial production of four concentrates: (I) lead concentrates, (2) zinc concentrates, (3) acid-grade fluorspar concentrates and (4) metallurgical-grade fluorspar concentrates.2,3 Although fluorspar had been floated in Canada in 1921 4 and a plant at Rosiclare had been floating fluorspar since March 1929, fluorspar flotation was given considerable impetus by the Mahoning developments, since some features of the separation were quickly adopted by other fluorspar companies. The Bureau of Mines5 reports that in the 10 years preceding 1938 only 50,552 tons of fluorspar flotation concentrates were produced in the United States. The rise from this almost nominal figure to 153,750 tons (largely acid grade) in one year (1944)6 is indicative of the activity in fluorspar flotation occasioned by the war. The industry thus proved to be in a position to expand and keep up reasonably well with the requirements imposed upon it by such developments as occurred in high octane aviation gasoline alkylation, in the use of Freon as a refrigerant and as carrier in the Aerosol "bug bomb," and in the atomic bomb project as well as in the expansion of other activities requiring hydrofluoric acid; such as, for example, the aluminum industry. Despite the fact that the greater portion of acid-grade fluorspar produced in the last few years went directly into war uses, the future of the acid-grade field still appears bright. As a result of the activity in fluorine chemistry during the war, it seems likely that in the relatively near future almost every phase of human endeavor will find some fluorine compound involved. The other three concentrates produced deserve some attention in these introductory remarks. The lead concentrates first produced contained both zinc and fluorspar but these did not interfere with their marketing. As will be pointed out later, the quality has steadily improved until today it is a relatively high-grade product. Although some zinc smelters accept concentrates containing limited quantities of fluorspar, it is a very objectionable impurity. Since flotation methods fail in the complete removal of the fluorspar, chemical methods were developed for

Jan 1, 1946

By Frank Woolley, John F. Elliott

The high-temperatzrre solulion calorimeter has been modified and an extension dynamic analysis of i/s transient behavior has provided an improved basis for interpretation of the experimental data. The partial molar heats of mixing, Him, of aluminum, copper, and silicon in the corresponding binary liquid-iron alloys haz,e been measured directly at 1600°C. The resulls in kcal per g-alom are: THE high-temperature1,2 solution calorimeter was planned and designed to obtain directly the partial molar heat of solution of solute elements in a variety of liquid metals that might serve as solvents. Results obtained in the temperature range of 1000° to 1200°C were described in the two earlier publications. However, a long-term goal in the program has been to obtain measurements at 1600°C of the heats of solution of elements in liquid iron. Hence, subsequent to the work last reported,2 and based on the experience of the first two studies, the calorimeter system has been modified and operated at 1600°C to obtain measurements on the Fe-Si, Fe-A1, and Fe-Cu systems. This paper reports the results of the work. THE MODIFIED SYSTEM It was clear from the earlier results that the most precise measurements can be obtained with the high-temperature solution calorimeter when the solution time is less than approximately 30 sec. This can be achieved only when the bath temperature, Tb, is above the melting (liquidus) temperature of the solute material being dropped. A second point of importance is that the refractories used earlier liberated considerable water so that, although the oxygen potential of the atmosphere in the system was satisfactory for work with nickel and copper, it was too high for work with iron, silicon, and so forth. Third, for work at 1550" to 1650°C, an improved temperature-sensing unit is needed. The modified calorimeter in its latest form is shown schematically in Fig. 1. The refractory brick and the Kanthal-Super heating elements which formed the furnace for heating the solute addition have been replaced by a smaller resistance-heated tube furnace which is insulated with bubble-grain alumina. A more elaborate gas purification system was installed to maintain a satisfactorily low oxygen potential in the atmosphere of the calorinieter chamber and of the solute addition furnace. As was the case in the earlier work, at the beginning of a run the calorimeter chamber is evacuated and then filled with purified argon so that a total pressure slightly in excess of 1 atm is maintained during the run. When either of the furnaces within the enclosure attains a red heat, 6 pct H2 is added to the atmosphere. Throughout the run, gas from the calorimeter is circulated through a de-oxidation system at the rate of approximately 5 standard liters per min; the changeover time for the gas within the calorimeter enclosure is approximately 1 hr. The essential stages of the deoxidation system are: a copper furnace at 600°C, a drying tube of anhydrite, and a titanium furnace at 800°C. The oxygen potential of the gas stream in the purification system can be monitored at several points by a stabilized zirconia oxygen cell. This cell is invaluable in detecting the development of leaks in the container vessel and the gas circulating system. The installation of the solute-addition furnace allowed either of two types of temperature-sensing units to be mounted on a water-cooled probe. The first was a small optical device using a silicon diode that was

Jan 1, 1968

By T. G. Digges, M. R. Achter

ALTHOUGH zone melting has found favor in recent years because of its convenience and its faster rate of production of single crystals, the older technique of strain annealing still has a number of advantages. It has been reported1 that the lattice of a crystal prepared in this manner has fewer defects than one grown from the melt and, of course, the control of the external geometry is easier. Also, the diameter of the crystal which can be grown by zone melting has a theoretical limit determined by the surface tension, thermal conductivity, and specific gravity of the material, while the size of that which can be grown in the solid state is limited only by practical considerations. In a program for the study of the structure-sensitive properties of niobium and its alloys it was desirable, for ease of handling, to have available single crystals of large diameter. This requirement dictated the choice of the strain-anneal technique. Induction heating was chosen in the present work in preference to other methods because of its deep penetration of large-diameter sections. A five-turn coil, powered by a motor generator operating at 10,000 cps, is contained in a vacuum chamber. The work is lowered through the coil for both the recrystallization and the crystal-growth steps. Starting with electron-beam melted material, the bars are cold-swaged, recrystallized, strained in a tensile machine, and then subjected to the growth step. Single crystals have been grown under the following conditions: Reduction in area during swaging— 79 to 99 pct, recrystallization temperature—1500o to 1667°C at the rate of 1.25 in. per hr, strain—1.0 to 2.5 pct, growth temperature—1600o to 2400°C at rates from 0.15 to 1.25 in. per hr. Starting grain sizes achieved after the recrystallization step varied from 0.6 to 1.55 mm. The starting grain size was found to be critical; if it is too fine and has any residual cold work, as shown by the presence of a fiberlike texture, a single crystal cannot be grown. Using this technique niobium single crystals have been grown from 0.250 in. diameter and 12 in. long to 1.00 in. diameter and 5 in. long as shown in Fig. 1. The 1-in. crystal is the largest to be reported for a refractory metal as compared to 0.500 in. for molybdenum grown by zone melting.2 As with zone melting, control of orientation is possible by the use of special procedures. Other investigators, see for example Williamson and Smallman,3 have reported that orientation control may be achieved by a bending technique. In the present work the strained rod is partially lowered through the coil to start the growth of the crystal. Then it is removed and bent at a point ahead of the interface between the single and polycrystalline portions. Finally, it is returned to the chamber and growth is continued "around the corner". The amount of bending which can be imparted to the rod is limited by coil geometry which up to now has been 10 deg. However, by repeating the bending and growing operations it should be possible to attain any desired orientation. The perfection of these single-crystal specimens as a function of process variables is being measured by X-ray and metallographic techniques and the results will be reported in a forthcoming paper. This work was partially supported by the Advanced Research Projects Agency.

Jan 1, 1964

By S. C. Sun, John A. L. Campbell

Objective of the ittvestigation was to determine the electrokinetic differences, if ally, of anthracite lithotypes and thus establish the feasibility of making a coqlstituent separation by froth flotation or other surface-dependent processes. The elec-trokinetic properties were determined by streaming potential methods. In addition, chemical and physical analyses of the lithotypes were made to establish nonsubjec-tive parameters for their diflerentiation. Electrokinetic results indicate a difference in the characteristics of the lithotypes. The isoelectric points of 4 anthracites and 12 lithotypes were obtained. It was suggested that the relative flotation rates of the lithotypes were pH dependent and that the maximum flotation rate of anthracite occurs in an acidic circuit. Although there has been an increased interest in the electrokinetic properties of coal,' research on the subject is still in an early stage of development."' To the authors' knowledge, no electrokinetic studies have been made on coal lithotypes, particularly anthracite litho-types. This paper presents the results of an investigation of the double layer properties displayed at the anthracite/water interface (whole coal and lithotypes) as determined by streaming potential methods. It is hoped that this investigation and related future investigations will provide correlations from which the surface properties of any coal can be predicted and then related to surface-dependent processes such as froth flotation and flocculation. Another aspect of this research, undertaken to determine the physical and chemical parameters necessary for anthracite lithotype differentiation, was previously published.? The number of parameters involved, lithologic, organic and inorganic, and the wide divergence of these parameters within an individual coal limits the practical utilization of the results; however, the result? are of value and of interest in guiding theoretical developments. Keeping the limitations in mind, the results are analyzed in terms of their application to froth flotation processes and are used to indicate the feasibility of making a lithotype separation by flotation. Experimental Procedure Prior to discussing the experimental work per se, it would be of value to establish an understanding of anthracite lithology. Anthracite Lithology: Coal seams display two different modes of variation, rank and type. A coal's position in the continuous series ranging from peats through anthracites determines its rank. The rank of the material under consideration is anthracite. The different bands of coal which constitute a coal seam are distinctly contrasted in regard to physical properties and chemical composition. These megascopic bands are the coal types and are termed lithotypes., A megascopic examination of 11 anthracites revealed three distinct, homogeneous, lithotypes. The classic description of bituminous coal lithotypes as proposed by Stope" was found to be quite adequate for recognizing the three lithotypes in anthracite, namely vitrain, durain, and fusain. The term vitrain describes the brilliant constituent of coal; durain describes dull coal; and fusain is the term applied to fossil charcoal. The anthracites studied were generally found to contain 60-80% vitrain, 10-30% durain, and 1-10% fusain. A complete description of the physical characteristics and chemical composition of the studied lithotypes can be found in a previous publication.' Sample Preparation: Nine of the anthracites used in the investigation were from Pennsylvania, one was from Russia, and one from Wales. Table 1 shows the various designations and sources of the employed anthracites. The letter V, D, or F added to the whole coal designation indicates respectively the vitrain, durain or fusain lithotype of that coal. The samples were carefully collected to avoid contamination. To insure against oxidation, the samples were obtained as fresh as possible and stored under nitrogen or water. Generally a representative sample of the seam and samples containing high concentrations of one or another of the petrographic constituents were secured for each coal. Pure lithotypes were prepared by manual separation and selection. The pure lithotypes and representative samples were ground to —35 mesh and screened to 35 x 48 mesh. The 35 x 48-mesh fraction was then passed over a magnet to remove iron contamination, washed with doubly

Jan 1, 1971

By J. B. Wagstaff

The raceway in front of the tuyere of the blast furnace has been studied quantitatively and a correlation obtained for the penetrastudiedtion of the blast. Some evidence is presented for the height and width of the raceway which suggests that all the raceways of a ffurnace overlap. The size of the coke in this zone has been measfurnaceoverlap.ured photographically during normal operation and results are given for the various areas. IN an earlier paper,' it was shown that a raceway exists opposite each tuyere of a blast furnace. This raceway is formed by the jet effect of the air emerging from the tuyere and consists essentially of a turbulence in which coke particles are recir-culated at high speed. Its presence was deduced originally from observations on movies taken with a high-speed camera through the tuyeres of various furnaces and was confirmed by experiments made on a model. In the model described,' this raceway was shown as operating in a vertical plane only, although there was a suggestion in the motion-picture film exhibited at that time that the raceway was three dimensional, unless artificially restricted. There was also some doubt then about the factors influencing its size. This paper describes the next steps in the investigation. Since the size of the raceway is obviously of importance in the operation of the furnace, it seemed worth while to study the subject more carefully. It is probably in this region that about half the coke in the furnace is consumed, so that the movement of the stock column may well be controlled by raceway behavior. Furthermore, there is some evidence to suggest that the coke is packed densely in the center of the furnace to form the "dead man" and more loosely above the raceway. It is therefore probable that the bulk of the gases passing up the stack flow from the top surface of this raceway. Clearly then, a knowledge of this critical zone is of interest to the blast furnace operator, and the first half of this report is devoted to a quantitative discussion of the subject. A further topic of interest among operators is the degree of breakdown of coke in the furnace, with which is inseparably linked the importance of a strong coke. Indeed, the whole question of the optimum size and type of coke may be as dependent on the condition of the coke in the bottom of the blast furnace as at the top. Attempts have been made from time to time to obtain samples of coke from the tuyeres and other furnace openings but they all suffer from the fact that the coke is filled to a varying degree with metal and slag and is probably broken up by the very act of taking the sample. It has proved difficult to make any reliable studies of coke size by these methods. However, it did seem possible to use the highspeed movies mentioned earlier1 to estimate the size of the coke. These movies provide an accurate record of individual coke particles so that, in theory at least, it should be possible to measure the size of the particles one by one and to obtain, for the first time, information on the coke being blown around the raceway under actual operating conditions while the furnace is performing normally. Such a study has been made and is discussed in the second half of this paper. The results obtained enabled the blast furnace data to be correlated with the model results given in the first half. Raceway Size In order to make a quantitative study of the size of the raceway it was necessary to devise some apparatus of laboratory scale, which could be handled quickly and easily. This focused attention on models, which in turn means that the laws of similarity governing this particular process must be ascertained. Method of Procedure: Since the work was to be carried out on a smaller scale than the blast furnace, the linear dimensions of the model became unimportant provided that the scale was known; it is only important to insure that the container does not affect the raceway being observed. The studies therefore were carried out in a glass-sided box, 11 in. high x 7 in. wide x 3 in. deep, using air jets ranging

Jan 1, 1954

By V. K. Grotzky, F. J. Fraikor

A number of investigators have noted the importance of various precipitation reactions on the properties of commercial-purity beryllium.1-5 Carrabine, for example, has demonstrated the interaction of iron and aluminum on the mechanical properties of hot-pressed polycrystalline beryllium.6 He considered the determining factor on elevated-temperature properties to be a reversible AlFeBe, precipitation reaction which could be directly related to the Fe/Al impurity ratio of the beryllium. Any aluminum in excess of the stoichio-metric amount required to form A1FeBe4 was presumed to remain primarily in the grain boundaries. We have observed, by transmission electron microscopy, such a grain boundary effect after various heat treatments of beryllium sheet. The starting material in this investigation was bare-rolled beryllium ingot sheet (0.001 to 0.005 in. thick), in contrast to the hot-pressed powder utilized by Carra-bine. It should be noted from the ingot sheet analysis shown in Table I that the Fe/Al weight ratio was near unity which would provide some free aluminum although the total aluminum and iron content was still small. Fig. l(a) shows some aluminum or aluminum-rich precipitates in the grain boundaries of a beryllium foil which had been quenched from 1200°C into brine at -TPC. Similar grain boundary precipitates were found, particularly at grain boundary intersections, in other samples quenched from 1100° and 1000°C. The length of annealing time at these elevated temperatures did not appear to substantially alter the amount of grain boundary precipitates, thus attesting to their relative insolubility. No matrix precipitates were observed other than the normal BeO and Be2C inclusions. A microprobe analysis of the larger precipitates at

Jan 1, 1968

By Walter E. Duncan

The ores treated at the concentrating plant of the Mahoning Mining Co. at Rosiclare, Ill., come largely from the blanket replacement deposits of the northeastern part of Hardin County, Illinois, and consist of complex mixtures of galena, sphalerite and fluorspar in a gangue of quartz, limestone and sandstone. The several minerals are so intimately inter-grown that they are not liberated at the sizes usually treated by gravity concentration in the usual fluorspar plant. For this reason, an all-flotation method of concentration was developed in cooperation with the station of the U. S. Bureau of Mines at Rolla, Mo.1 This flotation separation made possible the commercial production of four coyentrates: (I) lead, (2) zinc, (3) acid-grade fluorspar and (4) metallurgical-grade Auorspar.2-3 Although fluorspar had been floated in Canada in 19214 and a plant at Rosiclare had been floating fluorspar since March 1929, fluorspar flotation was given considerable impetus by the Mahoning developments, since some features of the separation were quickly adopted by other fluorspar companies. The Bureau of Alines5 reports that in the 10 years preceding 1938 only 50,552 tons of fluorspar flotation concentrates were produced in the United States. The rise from this almost nominal figure to 153,750 tons (largely acid grade) in one year (1944)6 is indicative of the activity in fluorspar flotation occasioned by the war. The industry thus proved to be in a position to expand and keep up reasonably well with the requirements imposed upon it by such developments as occurred in high octane aviation gasoline alkylation, in the use of Freon as a refrigerant and as carrier in the Aerosol "bug bomb," and in the atomic bomb project as well as in the expansion of other activities requiring hydrofluoric acid; for example, the aluminum industry. Despite the fact that the greater portion of acid-grade fluorspar produced in the last few years went directly into war uses, the future of the acid-grade field still appears bright. As a result of the activity in fluorine chemistry during the war, it seems likely that in the relatively near future almost every phase of human endeavor will find some fluorine compound involved. The other three concentrates produced deserve some attention in these introductory remarks. The lead concentrates first produced contained both zinc and fluorspar but these did not interfere with their marketing. As will be pointed out later, the quality has steadily improved until today it is a relatively high-grade product. Although some zinc smelters accept concentrates containing limited quantities of fluorspar, it is a very objectionable impurity. Since flotation methods fail in the complete removal of the fluorspar, chemical methods were developed for

Jan 1, 1948

By Walter E. Duncan

The ores treated at the concentrating plant of the Mahoning Mining Co. at Rosiclare, Ill., come largely from the blanket replacement deposits of the northeastern part of Hardin County, Illinois, and consist of complex mixtures of galena, sphalerite and fluorspar in a gangue of quartz, limestone and sandstone. The several minerals are so intimately inter-grown that they are not liberated at the sizes usually treated by gravity concentration in the usual fluorspar plant. For this reason, an all-flotation method of concentration was developed in cooperation with the station of the U. S. Bureau of Mines at Rolla, Mo.1 This flotation separation made possible the commercial production of four coyentrates: (I) lead, (2) zinc, (3) acid-grade fluorspar and (4) metallurgical-grade Auorspar.2-3 Although fluorspar had been floated in Canada in 19214 and a plant at Rosiclare had been floating fluorspar since March 1929, fluorspar flotation was given considerable impetus by the Mahoning developments, since some features of the separation were quickly adopted by other fluorspar companies. The Bureau of Alines5 reports that in the 10 years preceding 1938 only 50,552 tons of fluorspar flotation concentrates were produced in the United States. The rise from this almost nominal figure to 153,750 tons (largely acid grade) in one year (1944)6 is indicative of the activity in fluorspar flotation occasioned by the war. The industry thus proved to be in a position to expand and keep up reasonably well with the requirements imposed upon it by such developments as occurred in high octane aviation gasoline alkylation, in the use of Freon as a refrigerant and as carrier in the Aerosol "bug bomb," and in the atomic bomb project as well as in the expansion of other activities requiring hydrofluoric acid; for example, the aluminum industry. Despite the fact that the greater portion of acid-grade fluorspar produced in the last few years went directly into war uses, the future of the acid-grade field still appears bright. As a result of the activity in fluorine chemistry during the war, it seems likely that in the relatively near future almost every phase of human endeavor will find some fluorine compound involved. The other three concentrates produced deserve some attention in these introductory remarks. The lead concentrates first produced contained both zinc and fluorspar but these did not interfere with their marketing. As will be pointed out later, the quality has steadily improved until today it is a relatively high-grade product. Although some zinc smelters accept concentrates containing limited quantities of fluorspar, it is a very objectionable impurity. Since flotation methods fail in the complete removal of the fluorspar, chemical methods were developed for

Jan 1, 1948

By J. F. Havard

Gypsum is a useful industrial mineral found abundantly on the earth's crust. It is inexpensive to mine and process, and its calcined products have a wide range of readily controllable properties such as strength, density and setting time. It has proven to be such a useful material indeed, that ten American companies, operating some 57 calcining plants in 25 states in 1958, produced or imported in that year a total of 13,649,000 tons of the crude mineral valued at $39,361,000, which they then converted into manufactured products with a value of $329,070,000. Gypsum (CaSO4.2H2O) is calcium sulfate with two molecules of combined water, which are responsible for most of its useful properties. It is closely associated in most deposits with anhydrite (CaSO4), which contains no combined water and has limited commercial value in the United States. Man has long recognized the useful qualities of gypsum. It was utilized by the Egyptians in the construction of the pyramids and, later, by the Romans for important structures. Many of the ancient peoples prized gypsum for artistic and ornamental purposes, carving statuary from alabaster and making casts with plaster. The tabular variety, selenite, was used for windows, and the light transmitted through these windows reminded people of light from the moon (selene), hence the name selenite. The use of gypsum continued through the Middle Ages and into modem times. Benjamin Franklin was a famed exponent of gypsum because he applied ground gypsum to clover fields in the form of large letters which later read, in the more luxuriant growth, "land plaster used here." Gypsum is still used as an effective conditioner for some soils, but in recent decades, particularly in North America and Europe, it has become much more important as a major material for the building industry. Description Gypsum and anhydrite are closely associated minerals. Gypsum is found in a number of forms: massive rock gypsum, alabaster, selenite, satin spar, and gypsite. Anhydrite is found as massive rock or as smaller bodies or isolated crystals included in gypsum. Massive Rock Gypsum comprises most of the commercial gypsum and occurs as a sedimentary rock, interbedded in most places with shale, limestone or dolomite. This rock is soft and crystalline. Its color is white or shades of gray, pink, yellow, brown or other colors. Alabaster is a pure, compact and fine-grained variety suitable for use in sculpture or turning into artistic forms; it may be white or selected for attractive coloration. Selenite is gypsum crystallized in flat, transparent, flexible foliated plates, found in clays or in surface vugs in gypsum. Satin Spar is a fine silky fibrous variety with the axes of the crystalline fibers perpendicular to the vein or joint in which it has formed. Gypsite is an earthy mixture of gypsum with clay and sand in secondary formations; it is sometimes useful as a soil conditioner and has been used in making base-coat plasters. Pure gypsum contains 20.9 pct combined water, 46.6 pct sulfur trioxide (SO3) and 32.5 pct lime (CaO). Standard specifications (American Society for Testing Materials Designation C 22-50) read that minimum purity for material to be called gypsum is 70 pct CaSO4.2H20. Most of the commercial gypsum is 85 to 95 pct pure as produced. Impurities in

Jan 1, 1960

By James A. Barr

Phosphate rock is a natural rock containing one or more phosphate minerals usually calcium phosphate, of sufficient purity and quantity to permit its use, either directly or after beneficiation in the manufacture of commercial products.1 The principal minerals in phosphate rock have the apatite structure which may be represented by the type formula: Ca10(X2) (PO4)6 where X represents the hydroxyl group (OH), chlorine or fluorine, either singly or collectively. The calcium may be partly replaced by sodium, magnesium, and other positive ions such as manganese, strontium, lead, uranium, cerium, yttrium and other rare earths. The PO4 radical may be partly replaced by small quantities of UO4, AsO4, SiO4, CO3, SO4, or Vo4. A typical commercial rock is usually a calcium phosphate containing 3 to 4 pct fluorine, the major impurities being limonite or other iron oxides, clay, aluminum phosphates and silica as quartz sand. A little vanadium is present in most of the domestic rock deposits (except the Tennessee Brown Rock), according to Jacob, Hill, Marshall and Reynolds! A little uranium occurs in the Florida leached zone, as will be brought out later. The chemical analyses are reported as P205, or tricalcium phosphate Ca3(PO4)2, the latter often designated by the trade name BPL (bone phosphate of lime). Commercial analyses usually report iron and alumina as oxides, lime as CaO and silica or insoluble. Colony3 examined many samples of apatite, staffelite, dahlite and American phosphorites and concluded that all have identical X-ray diffraction patterns. The phosphates in the phosphate rock have very minute crystalline structures. The mineral apatite Ca3(F.Cl) (PO4) 3 is the principal primary source of the element phosphorus, and occurs widely distributed in igneous rocks but rarely in a minable mass. Only about 12 pct of the world production of phosphate rock comes from primary apatites; the remainder is derived from secondary phosphorites. These phosphorites have been formed by the alteration of sediments by solutions containing phosphoric acid. Such solutions have come from the weathering or leaching of igneous rock containing apatite, bone deposits of prehistoric animals, marine life or guano deposits. These phosphorites are mostly alterations of phosphatic limestones. The sedimentary phosphate deposits are of marine origin and may have been enriched by subsequent solution of the more soluble calcium carbonate by waters containing carbon dioxide, by physical concentration by wave action, and by redeposition of the dissolved phosphate ions. Uses of Phosphate Phosphorus is the spark of life and is the structure builder and one of the main elements of plant food (fertilizer). Without phosphorus, life cannot exist. A "complete" plant food[t] in addition to phosphorus compounds contains potash, which acts as a catalyst to convert nutrients to useful forms, nitrogen to supply the growth element and many minor elements. The cycle of supply of phosphorus is from the apatite to solution and soil, absorption of plant life, decay and return to the soil or by animal life feeding on the plants. With insufficient supply of phosphorus in vegetation, life is not prolific. If crops are removed from

Jan 1, 1960

By J. G. Eenink, R. A. Cunningham

One phase has been completed of a laboratory invesrigation of formations with relatively high permeability under conditions of overburden, formation and mud coltrmn pressures. The following statements are based on these tests within the limitations described. Drilling rate decreased when mud column pressure was greater than formation pressure. The decrease was primarily due to a layer of cuttings and mud particles held to the hole bottom by the difference in pressure. Much of the force of the bit was wasted in this layer and was unavailable for penetrating virgin formation. Adequate jet velocities helped clean the filter cake and chips away and resulted in increased drilling rate — the higher the jet velocity the faster the drilling rate. Drilling rate increased slightly when formation pres sure was greater than mud column pressure. The i11(reuse resulted from cleaning the hole bottom as formarion fluid flowed into the borehole. Overburden pressure had practically no effect on drilling rate. INTRODUCTION Some formations are difficult to drill in a wellbore hole but are easily drilled under atmospheric conditions in the laboratory. The reasons for this apparent difference in drillability are not fully understood. An increase in formation compressive strength causes a reduction in drilling rate. It has been shown by Griggs1, Handin2 and others3-1 that formation strength increases under conditions of high hydrostatic stress. Based on these results, a decrease in drilling rate would be expected with increased drilling fluid pressure in formations of low permeability having low formation fluid pressure. Such a decrease has been shown by Murray. et a1 and Eckel" This effect holds even when using nitrogcn under high pressure as the drilling fluid (unrc-ported tests from the Hughes laboratory). Poor bottom-hole cleaning may account for decreased drilling rates. Even though it may not be easily explained, evidence of poor cleaning can easily bc seen. One evidence is the increased drilling rate that accompanies decreased balling obtained with addition of oil in some muds used to drill shales.4,7,3 Many variables can affect drilling rates. These may include mud composition and properties, formation properties, bit types and operating conditions, formation fluid, mud column and overburden pressures. These must be studied a few at a time under carefully controlled conditions which simulate actual conditions as closely as possible. The purpose of this work was to investigate effect of overburden, formation and mud column pressures on drilling rates in permeable formations. These tests were suggested by conditions shown in Fig. I. Represented is a borehole drilled into a formation with relatively high permeability. In the vicinity of the hole bottom there exists a mud column pressure, P a formation fluid pressure, P and an overburden pressure, The mud has low water-loss properties and sufficient weight to more than overbalance the formation pressure. Laboratory investigation included a range with formation pressure greater than mud column pressure. NOMENCLATURE Pm mud column pressure = pressure of drilling fluid or mud at hole bottom Pf, formation pressure = pressure of fluid in intersticies of formation

By D. E. Mikkola, G. E. Poquette

X-ray diffraction was used to study the growth of antiphase domains in quenched (or "disordered&apos;? Cu3Au annealed in the range 300" to 385°C. Measurements of the long-range order parameter indicate that a high degree of order is established rapidly at these annealing temperatures. Average domain sizes obtained by Fourier analysis of the superlattice peak profiles show that antiphase domain growth is analogous to classical metallurgical grain growth (i.e.,fol-lows a D2 US kt relation). The activation energy for the growth process, 44 kcal per mole, indicates diffusion control. The anisotropy in the observed effective domain sizes from seven different superlattice peaks can be best accounted for by a configuration involving antiphase domain boundaries on {100 } and (111 ) planes, where the (100) boundary is the low-energy type, {lOO} Type I. The disappearance of the (111) antiphase domain boundary during domain growth is dif-fusion-controlled with an activation energy of 48.5 kcal per mole. On the other hand, the behavior of the parameter representing the amount of (100) Type I boundary indicates that there may be a conversion of the higher-energy boundary types to (100) Type I boundary during the growth process. THE order-disorder transformation in the alloy Cu3Au has been the subject of numerous experimental investigations over the past 40 years, most of which have involved measurements of convenient physical properties such as resistivity and hardness as a function of heat treatment. The interpretation of these data is difficult because measurements of this type have the disadvantage that they yield total changes resulting from several different atomic processes which may be occurring simultaneously. The present study was undertaken to establish by means of X-ray diffraction the kinetic behavior of one of these atomic processes, namely antiphase domain growth. In the completely ordered state Cu3Au has an L12 structure which can be described as an fcc type arrangement of atoms in which the gold atoms occupy the corner sites and copper atoms the face-centered sites. Three other equivalent unit cells can be formed by allowing two gold atoms to occupy opposite face-centered sites and copper atoms to occupy the remaining corner and face-centered sites. These four different unit cells are crystallographically related by a shift of 1/2<110>. Quenching from above the critical temperature (392°C) to room temperature retains the "disordered" structure-a "random" arrangement of copper and gold atoms having the fcc structure. Annealing the disordered alloy below the critical temperature causes ordering to occur through the nucleation and growth of ordered regions at different points throughout the crystal. These small ordered regions, each based on one of the four types of unit cell, grow by consuming the disordered material until they impinge to form a domain structure in which the domains are antiphase by a shift of 4(110). The boundaries between domains are called antiphase domain boundaries (APDB) and they have been found to lie primarily on &apos; {100} planes in highly ordered Cu3Au. Two types of APDB can occur on ( 100) planes. An example of an (001)1/2[110] shear type APDB is shown in Fig. I. Because of the layer of copper atoms separating the domains in this case, there are no near-neighbor violations across the boundary and it has a low surface ener This type of APDB will be referred to as {lOO} Type I. Fig. 2 shows an (001): [011] climb type APDB, (100) Type 11. This type of APDB can be described as resulting from removal of a (200) plane followed by a shift of 1/2<110> to bring the separated regions together. Near-neighbor violations across (100) Type I1 APDB make it a high-energy boundary. There are numerous other possible APDB configurations; however, it is only worth noting that shear type APDB can be produced on the (111) plane by motion of a normal fcc dislocation with Burgers vector 1/2<110> through the ordered structure. A (111); [110] shear type APDB is shown in Fig. 3. Again, because of the near-neighbor violations this type of APDB has a higher energy than the (100) Type I APDB.

Jan 1, 1970