Search Documents

By F. S. McNicholas

IN the writer's opinion the term "block caving" has been rather loosely applied to a general principle of mining, and therefore detailed classification of caving methods and draw, together with the characteristics required for each method, will fill a desired need. Selection of caving method should be made only after a study of all governing conditions, such as size of orebody, lateral and vertical extent of ore-body, attitude, treatment demands, possible resultant pressures, and cost and profit comparison of methods. Successful caving methods can be classified under six main headings: (1) Full-protected block caving, (2) semi-protected block caving, (3) unprotected block caving, (4) full-panel caving, (5) half block-panel caving, (6) block-panel caving. The methods and factors governing choice of method are shown in Table I. Full-protected Block Caving Full-protected block caving consists of develop-ing, undercutting, and drawing to exhaustion a block of ore of predetermined size without coordination of mining or draw with adjoining areas. The block is mined and drawn as an independent unit (Fig. 1). Full-protected block caving demands that mining and draw cannot be done against unconsolidated capping in adjoining caved and exhausted blocks. Two sides of block are against solid. Caved capping must be allowed to consolidate for a suitable period, usually not less than one year. Pillars may be left in lieu of consolidated capping (Fig. 2). The advantages of full-protected block, caving are: (1) A definite area is developed, mined, and drawn as a unit so that all work may be completed, the block drawn to exhaustion in the minimum length of time, and the area then abandoned. (? Production is not restrained because of coordina1, on with adjoining areas. (3) Records of draw and caved reserve of ore are good. Upon abanwnment of the block, accountability for production is closed out with no carry-over to adjoining areas. The disadvantages of full-protected block caving are: (1) Side dilution from the draw adjacent to the consolidated capping may be serious, particularly where capping does not consolidate sufficiently in the allotted time. (2) Boundary weakening is needed on the solid sides of the block except in weak rocks. (3) Maximum cantilever and compression effect to aid caving and fragmentation may not be secured since the draw should proceed from the solid to the consolidated capping to minimize side dilution. However, undercutting from the loose (caved capping) to the solid with a slight initial draw in the same manner will develop cantilever effect. (4) A period of at least one year, more is usually desirable, must be allowed for caved capping ,to consolidate before mining the adjoining block, depending upon the characteristics of the capping. (5) Capping may not consolidate sufficiently in the time that can be allowed. Full-protected block caving is indicated where: (1) The ground is weak and heavy and workings

Jan 1, 1952

By T. W. Smoot

Bentonites are composed chiefly of montmorillonites which are clay minerals generally distinguished from other clay minerals by their surface activity and extremely fine particle sizes. The uses of bentonite are many and varied, depending principally on one or more of the following characteristics: 1) Thixotropy, 2) Dispersion, 3) Plasticity, 4) Swelling, 5) Surface area, activity, ab- and adsorbtive properties. Some of the major uses of bentonite are briefly reviewed as are the mineralogical and physical properties. The uses of X-ray diffraction, differential thermal analysis and other tests for physical properties are reviewed as to their uses in evaluation. In the past 40 years, the industrial uses of bentonite have grown to include many applications. The physical and chemical properties of bentonites are such that they can be used as catalysts, adsorbants, plasticizers, binders, drilling muds, and pelletizers. Not all bentonites, however, can be used for all of these purposes and some are probably of little or no value for any use. The purpose of this paper is to briefly review the mineralogical, physical, and chemical characteristics and variations of bentonites. The determination of these characteristics and their uses in industry are also reviewed so that these determinations can be used as guides for evaluation. DEFINITION OF BENTONITE The word bentonite, as used in this paper, refers to a clay material, usually (but not necessarily) the result of the in-place-weathering of volcanic ash. Its mineralogical composition is dominated by the clay mineral montmorillonite and generally carries other clay minerals and silica minerals as the major 'impurities'. For this discussion, such a definition is justified since most of the economic uses of bentonite~ depend upon the physical and chemical characteristics of the montmorillonite minerals involved. The terms montmorillonite and bentonite have been used almost interchangeably in industry although the latter is much more commonly used. Therefore, where montmorillonite is discussed, it should be understood that the major feature of a bentonite is the subject. STRUCTIJRE OF MONTMORILLONlTE The economic importance of bentonites is generally based on one or more of the following characteristics of montmorillonite: 1) high-thixotropy and easy dispersion in water, 2) high-plasticity, 3) swelling properties, 4) large surface area/unit mass, 5) high surface activity, and 6) adsorptive properties. To understand these properties, an appreciation of the structural scheme of montmorillonite is helpful. Montmorillonite IS one of the three-layer clay minerals composed essentially of hydrous aluminum silicates. The essential building blocks of these layered silicate:; are: 1) silica tetrahedron composed of a silicon atom surrounded by four oxygen atoms, and 2) aluminun (iron, magnesium, etc.) octahedral unit that, ideally, has one of these atoms surrounded by six hydroxal units. Fig. 1 is a diagrammatic sketch of the montmorillonite structure. In the montmorillonite structure, the tetrahedron are pointed inward and attached to the octahedral units so that the O= atoms replace the hydroxal units where they are bonded; hence two-thirds of the hydroxal units

Jan 1, 1962

By V. A. Phillips, M. Safdar Ali

The tensile properties of Cu-0.20 pct Al, Cu-0.45 pct Mg, Cu-0.27 pct Cr, and Cu-0.22 pct Be solid-solution alloys were studied at -196°, 18°, 2509 and 500°C on wires internally oxidized at 900°and 1000°C. Internal oxidation produced marked increases in yield strength relative to pure copper, particularly at low temperature. The yield strength decreased with increase in temperature to a much greater extent than predicted by current theories of dispersion hardening. The strengthening effect of internal oxidation persisted throughout the entire stress-strain curve, but since a marked loss of ductility occurred at all test temperatures, only modest increases in tensile strength were realized. INTERNAL oxidation involves the preferential oxidation of a baser solute in a relatively noble solvent by diffusion of oxygen into the solid. Since the process is diffusion controlled, it is expedient to carry it out at a high temperature often approaching the melting point. The amount of solute is limited and the oxidation conditions adjusted so that oxygen diffuses inwards to meet the solute causing reaction to progress inwards and form subscale instead of only sur face scale. The reaction can be made to occur throughout the thickness of thin material producing a fine dispersion of oxide inside the metal. C. S. Smith1"3 appears to have been the first to recognize the true nature of the process of internal oxidation. Although extensive kinetic and metal-lographic studies followed by Rhines and coworkers,4-5 Chaston7 andMeijering and Druyvesteyn8 working independently were the first to report hardening effects due to internal oxidation. These results prompted detailed studies of the effects of internal oxidation on the hardness, tensile, creep, and fatigue properties of a number of alloys by G. C. Smith and coworkers9-12 in England, on hardness by Gottardi13 in Italy, and on hardness and tensile properties by wood14 in the U.S.A. Publications dealing with other aspects of internal oxidation will not be reviewed here. Internal oxidation of solutes having a high affinity for oxygen provides a means of obtaining very fine dispersions stable in a suitable atmosphere at temperatures well above those at which most age harden ing precipitates coalesce. The process therefore offers a method of producing thin sheet and wire of possibly outstanding creep resistance. The size limitation might be overcome by internally oxidizing porous powder compacts made from alloy powder before final sintering. PREPARATION OF ALLOYS The alloy ingots, which were approximately 5 1/2 in. long by 1 in. diam, were made up in a high-frequency furnace, using as raw materials OFHC copper, 99.99 + pct Al, high-purity magnesium, and master alloys of Cu-4.19 pct Be and Cu-10 pct Cr. The alloys containing aluminum and magnesium were melted ii closed high-purity graphite crucibles and solidified in the crucible which was lowered partly Out of the coil to give a hot-top effect. The alloys containing beryllium and chromium were made by melting in vacuo in alumina-lined sillimanite crucibles. The magnesium, chromium, and beryllium

Jan 1, 1960

By E. H. Crabtree, Neil S. Parker

THE custom milling plant of the Eagle-Picher Mining and Smelting Co. is at Sahuarita, Arizona, approximately 20 miles south of Tucson. It is connected by a 2-mile railroad spur to the main line of the Southern Pacific Railroad between Tucson and Nogales. The capacity of the plant is 500 tons per day. The mill is conventional except perhaps in the rather wide variety of ores treated. These vary from straight copper ores, from which only one concentrate is produced, and lead-zinc or copper-zinc ores from which two concentrates are produced, to complex gold-silver-copper-lead-zinc ores, which require the simultaneous production of three or four concentrates. Custom ores are received in lots varying in size from a few truckloads to several carloads. Similar ores, after crushing and sampling, may be commingled, or individual lots may be milled individually. The ores are first dumped either into one of two 200-ton railroad bins, or into one of the two 75-ton truck bins. From these bins the lot of ore is individually crushed in a 24 by 16-in. jaw crusher to 3-in. size, and then to 1/2-in. size in a 3-ft Symons shorthead crusher. After crushing to 1/2-in., the ore is conveyed to the automatic sampling plant. This consists of three Vezin samplers in series, each successively cutting out 10 pct, to pct and 5 pct of its feed. After No. 1 sampler, the material passes through a mixing barrel and is then crushed to 1/4-in. in a set of rolls before passing to No. 2 sampler. Between No. 2 and No. 3 samplers, the ore is again mixed in a mixing barrel. The final sample, consisting of one pound per ton of ore, is taken to the laboratory, where it is further crushed to 1/8-in. in a coffeemill, and then riffled down to the size required for grinding in a pulverizer. The capacity of the crushing and sampling plant is up to too tons per hour, depending upon the character of the ore. After sampling, the ore is stored in five ore-storage bins, consisting of four 200-ton bins and one 175-ton bin. Each of these bins is discharged by means of belt feeders and conveyor to the ball mills, so that ores may be composited for milling in any required ratio, or milled separately by themselves. Fine grinding is done in one 6 by 4-ft Allis-Chalmers ball mill and one 8-ft by 36-in. Hardinge mill. These two mills both discharge to one 54-in. Akins Simplex Highweir classifier. The classifier sands can be returned to either or both mills, so that flexibility in grinding for different ores is easily obtained. Flotation equipment consists of four 66-in. Fagergren machines for copper-lead roughing and six similar machines for zinc roughing. Lead-copper bulk concentrate is cleaned and recleaned in eight No. 18-S Denver machines, and zinc concentrate is cleaned in three 66-in. Fagergrens. Copper-lead differential separation

Jan 1, 1947

By F. E. Streigert, J. H. Mallery, A. H. Geisler

The existing data on precipitation in Cu-Be alloys have been reconciled with some new data to present a more complete and rational analysis of the atomic rearrangements involved in the process. Two different coherent precipitates were proposed. Each is responsible for a type of diffuse X-ray diffraction effect. THE nature of the atomic rearrangement involved in the precipitation of the compound y-Cu-Be from supersaturated solid solutions of the copper-base alloys has been the subject of two extensive investigations.'-" he precipitate in this alloy system has a rather simple structure; at equilibrium it has a body-centered cubic unit cell with copper atoms on the corner sites and beryllium atoms on the center site. While a simple mechanism would be expected to obtain for the precipitation process, those which have been proposed do not adequately explain all of the reported data. The purpose of the present report is to rationalize some of the previous observations and to contribute new data on the subject obtained by the usual techniques of structure analyses. The Cu-Be system of alloys represents one of the most extensively investigated precipitation systems, so a detailed review of the pertinent literature on structure is in order. Striations: Since one of the important features of the mechanism—the habit plane—is determined by microscopic examination, microstructural features that have been observed should be considered at this time in order to assess their role in the precipitation process in Cu-Be alloys. One of the most prominent features appears as regularly oriented markings or stripings (ripples or striations) across the crystals on a suitably polished and etched sample of the aged alloy. These have been observed and interpreted by many workers. Masing and Dah14 observed striations in both the a and /3 phases of a 2.5 pct Be alloy, and attributed them to the beginning of the precipitation of very fine y crystals along favored planes of the a matrix and to the local decomposition of the £ crystals into a plus y. These markings were apparent in both the a and /3 phases of the micrographs given by Smith5 for a 2.75 pct Be alloy, while Moore" detected them in the a matrix phase using polarized light. Desch7 attributed the markings to fine precipitate particles lined up on a family of matrix planes like Masing and Dahl had done, and he identified the planes as those of the (111) family, the slip planes of the matrix. The striations were presumably the structure which Northcott- eferred to as "martensitic." He found that this structure was present in samples that had been aged under widely different conditions with hardness values ranging from 160 to 400 VHN. Later Guinier and Jacquet' also found striations in both the a matrix and secondary /3 phase. Their analyses showed that the striations were along (110) planes of the matrix phase, apparently in contradiction of the results of Desch. They found that the striations were developed during aging on the surface of a specimen that had been polished prior to aging.' On this basis they concluded that the striations represented mechanical deformation by slip along (110) planes of the matrix resulting from precipitation stresses.'" Similar but fainter striations were observed in the same manner on an A1-Cu alloy sample, in which the change in volume was much less than for Cu-Be alloys and

Jan 1, 1953

By D. H. Woodard, G. W. Geil, W. D. Jenkins

In a series of papers, the authors and their associates have shown the influence of four important factors on the technical cohesion limit.3-l6 By "technical cohesion limitv is meant the technically determin-able resistance to fracture. The four importarlt factors are the stress system, plastic deformation, temperature, and the strain rate, The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. The previously mentioned series of papers contains ample evidence that plastic extension increases the fracture stress of any polycrystalline metal, In a recent paper of the series,l5 moreover, it has been shown that the effect of plastic deformation on the fracture stress cannot be attributed to reorientation of internal flaws but is a work-strengthening effect, similar to the effect on the flow stress, $ Plastic deformation of steels, however, may not only cause work hardening, but may result in additional hardness because of strain aging. Some evidence that strain aging affects not only the flow stress but also the fracture stress, has been presented in a recent paper.14 In that paper, a study is made of the influence Of Plastic deformstion at room temperature on the fracture stress of ferritic steels at -188°C. The study is based on the results Of two-stage tests. In the first stage each specimen was extended a predetermined amount at room temperature; in the second stage the specimen was tested to fracture in liquid air. In most Of these tests the specimen remained in the testing machine during the interval of about one hour between the first and second stages, it was kept under a tensile load of about 500 lb and maintained at liquid air temperature. The effects of various amounts of .plastic deformation on the fracture stress were thus determined and curves were obtained to represent the influence of plastic deformation at room temperature on the stress at brittle fracture in liquid air.14 Two specimens Of ingot iron, however, were removed from the testing machine at the end of the first stage and several days elapsed before the specimens were tested to fracture in liquid air, As shown in Fig 8 of that paper," the points representing fracture of these specimens are far above the curve representing the results of two-stage tests without a rest interval between the stages. The evidence thus indicated that the fracture stresses of these two specimens were increased not

Jan 1, 1949

By G. W. Geil, D. H. Woodard, W. D. Jenkins

In a series of papers, the authors and their associates have shown the influence of four important factors on the technical cohesion limit.3-l6 By "technical cohesion limitv is meant the technically determin-able resistance to fracture. The four importarlt factors are the stress system, plastic deformation, temperature, and the strain rate, The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. The previously mentioned series of papers contains ample evidence that plastic extension increases the fracture stress of any polycrystalline metal, In a recent paper of the series,l5 moreover, it has been shown that the effect of plastic deformation on the fracture stress cannot be attributed to reorientation of internal flaws but is a work-strengthening effect, similar to the effect on the flow stress, $ Plastic deformation of steels, however, may not only cause work hardening, but may result in additional hardness because of strain aging. Some evidence that strain aging affects not only the flow stress but also the fracture stress, has been presented in a recent paper.14 In that paper, a study is made of the influence Of Plastic deformstion at room temperature on the fracture stress of ferritic steels at -188°C. The study is based on the results Of two-stage tests. In the first stage each specimen was extended a predetermined amount at room temperature; in the second stage the specimen was tested to fracture in liquid air. In most Of these tests the specimen remained in the testing machine during the interval of about one hour between the first and second stages, it was kept under a tensile load of about 500 lb and maintained at liquid air temperature. The effects of various amounts of .plastic deformation on the fracture stress were thus determined and curves were obtained to represent the influence of plastic deformation at room temperature on the stress at brittle fracture in liquid air.14 Two specimens Of ingot iron, however, were removed from the testing machine at the end of the first stage and several days elapsed before the specimens were tested to fracture in liquid air, As shown in Fig 8 of that paper," the points representing fracture of these specimens are far above the curve representing the results of two-stage tests without a rest interval between the stages. The evidence thus indicated that the fracture stresses of these two specimens were increased not

Jan 1, 1949

By Hans Allenius, R. T. Hukki

This paper describes in quantitative terms the effect of sharpness of classification on the performance of the closed grinding circuit. The analysis is based on a large number of laboratory experiments designed to simulate the two most common industrial closed grinding systems. The experimental results show quantitatively the degree of improvement achievable by more efficient classification. In an earlier paper1 the senior author has presented a trend showing qualitative analysis of mill and classifier performance in tile closed grinding circuit. According to this analysis, the master key to a major improvement appeared to be effective removal of finished fine material from the classifier sands, or in other words, improved sharpness of classification, leading simultaneously to a substantial reduction of the circulating load. One purpose of this paper is to present the results of a quantitative investigation of the closed grinding circuit. Another is to set forth the essential pertinent variables revealed by the quantitative experiments carried out by the junior author. In the two most common systems of closed-circuit grinding, (1) feed to the circuit is introduced into the grinding unit, normally the ball mill, operating in closed circuit with the classifier; or (2) feed to the grinding circuit is introduced into the primary grinding unit, normally the rod mill, discharging into the classifier in closed circuit with the secondary grinding unit, normally the ball mill. In the following discussion, these two systems are analyzed separately in the indicated order. BALL MILL - CLASSIFIER CIRCUIT The Test Apparatus and Procedure: The test appara- tus included: (1) a F 195 mm x 220 mm laboratory ball mill rotated at a speed 77% of the theoretical critical speed, and a 7-kg batch of F 20 mm-F 50 mm steel balls; (2) a conventional 65-mesh test sieve and a Ro-Tap sieve shaker serving as a classifier; and (3) a Permaran instrument manufactured by Outo-kumpu Co. for surface area determinations by the permeability method. As no continuous closed-circuit experiments could be brought about on a laboratory scale, the process was broken down into alternating grinding and sizing steps in such a way that the new feed plus the returning sands always formed a batch of 1000 gm. For each selected grinding period and for each selected sharpness of classification the basic steps were repeated six times. Steady-state conditions were then reached. Crystalline vein quartz was used as a test material. Feed to the process consisted of -10-mesh fraction of this quartz crushed in rolls. This fraction included 15% of-65-mesh material. Experimental Results: The general flowsheet is shown in Fig. 1. Table I gives the essential data obtained representing steady-state conditions under the indicated set of variables. The table is based on 110 grinding experiments, 440 screen analyses and an equal number of specific surface area determinations. Fig. 2 shows the relationship between the cumulative net energy consumption and the cumulative number of mill rotations as evaluated by separate experiments. Note that this relationship is not linear but is instead represented by a slight curve. The data given in Table I are presented in graphical form as follows: Fig. 3 shows the produced -65-mesh material in grams per minute vs. time of grinding in minutes; the sharpnesses of classification at 65 mesh were 100%, 75% and 50%. It is clearly indicated that the highest-capacity figures call for relatively short grinding times and for the sharpest possible classification. Fig. 4 presents the specific surface area on the final -65-mesh product in square centimeters per gm vs. time of grinding in minutes. In conventional mineral dressing processes, a final product characterized

Jan 1, 1969

By R. C. Earlougher, F. G. Miller, T. D. Mueller, H. J. Ramey

There are many studies of flow in radial systems that can be used to interpret unsteady rerervoir flow problems. Although solutions for systems of infinite extent can be used to generate solutions fur finite ow systems by superposition, application is tedious. In this paper a step is made toward simplifying calcu1ations of such solutions for finite flow systems. Superposition is used to produce a tabulu-lion of the dimension1e.s.s pressure drop function at several locations within a bounded square that has a well at its center. The square system provides a useful building block that may be used to generate flow behavior for any rectangular shape whose sides are in integral ratios. Values of the tabulated dimensionless pressure drop function are simply added to obtain the dimensionless pressure drop function for the desired rectangulm system. The rectangular system may contain any number of wells producing at any rates. Furthermore, the outer boundaries of the rectangular system may be closed (no-flow) or they may he at constant pressure. Mixed conditions also may be conyidered. Tables of the dimensionless pressure drop function for the square system are presented and various applications of the technique are illustrated. Introduction In 1945, van Everdingen and Hurst' published solutions for the problem of water influx into a cylindrical reservoir. Since this problem is mathematically identical with the depletion of a cylindrical reservoir with a well at the origin, the van Everdingen-Hurst solution may be used to study the depletion problem. In their analysis, they assumed that the fluid had a small, constant compressibility such that flow was governed by the diffusivity equation For a constant production rate q starting at time zero, van Everdingen and Hurst showed that the unsteady pressurc distribution for both finite and infinite systems could be expressed in terms of a dimensionless pressure 'Sabulations of the dimensionless pressure drop for a unit value of r, were provided by van Everdingen and Hurst,' and later by Chatas.' Others also presented values in graphical or tabular form." If the radius of the well becomes vanishingly small, r,+ O, the line source solution may be used for Eq. 2 when infinite systems are considered. Eqs. 5 and 6 are excellent approximations for Eq. 2 under certain conditions: In 1954, Matthews, Brons and HazebroekV emonstrated that solutions such as Eq. 5 can be superposed to generate the behavior of bounded geometric shapes; i.e., the behavior of a bounded single-well system can be calculated by adding together the pressure disturbances caused by the appropriate array of an infinite number of wells producing from an infinite system. These wells are referred to as image wells. Matthews, Brons and Hazebroek considered systems containing a single well producing at a constant rate. This superposition can be represented analytically as

Jan 1, 1969

By Stirling Huntley

With the threatened falling off in production of the lighter oil pools of the Tampico embayment in Mexico, a general search of that country for oil-producing regions has resulted in renewed activity in the region of the Isthmus of Tehuantepec, one of the first districts exploited in Mexico. Since the drilling of the first well in the San Cristobal section by the Pearson interests in 1902, drilling has been continuous, except during 1917-1921, when practically all development was stopped by the revolutionary activity. Early in 1921, a drilling campaign was inaugurated for the purpose of testing out the known salt-dome poolfi on the flanks of the salt masses, rather than on their tops where previous tests had been located. On Dec. 7, 1921, the Aguila Co., with which are consolidated the Pearson interests and which has been the only company active in developing this region, unexpectedly drilled into a sand horizon at 3015 ft. with its Conception well No. 18. The hole was unable to handle the production, as a 1400-ft. string of 121/2-in. casing was hanging in the hole, a salt-water horizon drilled through at about 800 ft., was not cemented off, and 3000 ft. of 4-in. drill stem with rotary bit was in the hole. This well's potential capacity was never determined, but it made 7000 bbl. of 25" Bé. oil through the bit and Pin. drill stem, in one of its sporadic flows before sanding up, and thus proved itself capable of the largest potential production of any well on the Isthmus. The well showed salt water before caving and sanding up with the drill stem still in the hole, and will probably never be used for production. Wells Nos. 22 and 23, drilled nearby, have proved disappointments after making good showings of oil. In the spring of 1922, Ixhuatlan wells Nos. 28 and 29, deep tests supposedly on the flank of the known salt cores in that field, went into solid salt; No. 28 at 2250 ft. and No. 29 at 2400 ft. No. 28 was continued in the salt for 1000 ft. before operations were stopped. Later comple-

Jan 1, 1923

By Stirling Huntley

With the threatened falling off in production of the lighter oil pools of the Tampico embayment in Mexico, a general search of that country for oil-producing regions has resulted in renewed activity in the region of the Isthmus of Tehuantepec, one of the first districts exploited in Mexico. Since the drilling of the first well in the San Cristobal section by the Pearson interests in 1902, drilling has been continuous, except during 1917-1921, when practically all development was stopped by the revolutionary activity. Early in 1921, a drilling campaign was inaugurated for the purpose of testing out the known salt-dome poolfi on the flanks of the salt masses, rather than on their tops where previous tests had been located. On Dec. 7, 1921, the Aguila Co., with which are consolidated the Pearson interests and which has been the only company active in developing this region, unexpectedly drilled into a sand horizon at 3015 ft. with its Conception well No. 18. The hole was unable to handle the production, as a 1400-ft. string of 121/2-in. casing was hanging in the hole, a salt-water horizon drilled through at about 800 ft., was not cemented off, and 3000 ft. of 4-in. drill stem with rotary bit was in the hole. This well's potential capacity was never determined, but it made 7000 bbl. of 25" Bé. oil through the bit and Pin. drill stem, in one of its sporadic flows before sanding up, and thus proved itself capable of the largest potential production of any well on the Isthmus. The well showed salt water before caving and sanding up with the drill stem still in the hole, and will probably never be used for production. Wells Nos. 22 and 23, drilled nearby, have proved disappointments after making good showings of oil. In the spring of 1922, Ixhuatlan wells Nos. 28 and 29, deep tests supposedly on the flank of the known salt cores in that field, went into solid salt; No. 28 at 2250 ft. and No. 29 at 2400 ft. No. 28 was continued in the salt for 1000 ft. before operations were stopped. Later comple-

Jan 1, 1923

ANNUAL MEETING OF THE NEW YORK SECTION - The annual meeting of the New York Section was held at the Machinery Club, May 7. While the dinner, at which fifty attended, was in progress, the names of the nominees for next year's officers were posted. The result of the election was as follows: Chairman, E. P. Mathewson; vice-chairmen, William Y. Westervelt, R. M. Atwater, Jr.; treasurer, Wilber Judson; executive committeemen, Lucius W. Mayer, Edwin S. Berry. The subject for the evening was "Organization and Campaign in France of the 27th Engineers." Colonel O. B. Perry described the many difficulties surmounted, for it was necessary to work with untrained men ALLEN H. ROGERS WALTER S. DICKSON CHAIRMAN OF NEW YORK SECTION SECRETARY OF NEW YORK SECTION and shortage in supplies. He described the unusually fine character and physique of his officers, which made it possible to make the untrained men most efficient. He described in some detail the work of building bridges over the Meuse River and the bringing up of supplies to the first army base, in particular at the Argonne-Meuse sector; General Pershing gave a personal commendation of the work undertaken by this regiment. The Colonel described the methods of operating the transportation of ammunition and supplies to the "army dumps," by which at the time of signing the armistice there had been brought up 600,000 tons of equipment for use in the projected campaigns. An interesting item was that 3,600,000 sand bags had been provided, in case the Germans should be able to turn the line of the American troops. Captain Edwin S. Berry described the methods of sending materials to the front lines and gave figures to indicate the huge quantities required, adding that the order of preference was troops, ammunition, food, and engineers' supplies. The speakers then answered several questions given by the members present. WALTER S. DICKSON, Secretary.

Jan 6, 1919

By R. J. Teitel

FOUR or five years ago an investigation was initiated to study and develop basic information on llquid metal fuels for future power nuclear reactors. The objective was to find fluid forms of uranium (solutions or dispersions) in low melting alloys. A summary of the different fuels was presented in a recent article by Teitel, Gurinsky, and Bryner.' The combination of uranium and bismuth, with its low thermal neutron cross section and low melting point, is of basic interest to the development of these fuels. Most of the previous effort on the U-Bi phase diagram was done under security regulation. Ahmann and Baldwin' reported their findings on the U-Bi system in 1945. Their results indicated that the phase diagram had at least two compounds and possibly one more. UBi, and UBi were established by chemical analyses of residues after high temperature centrifugation of alloys. UBi, decomposed peritectically at1980°C and there were signs of another reaction above that. UBi melted at a very high temperature, and there were also signs of a monotectic at high temperatures in high uranium alloys. The solubility of uranium in liquid bismuth has received attention by three groups of authors: Bareis,X ayes and Gordon,' and Ahmann and Baldwin.' The latest and most widely accepted data is that of Bareis, and it is included in Fig. 1 along with new data at higher temperatures. Brewer et al." and Ferro"'' have used X-ray diffraction to determine the number and crystal structure of the compounds. Brewer identified the structure of UBi to be a simple NaCl cubic structure having a cell edge of 6.364A. The density of the compound was calculated to be 11.52 g per cu cm. Two other unindexed patterns were presented as possibly belonging to two other compounds. Ferro agreed with Brewer on the crystal structure of UBi and identified the structure of UBi, and U,Bi,. The intermetallic compound UBi, has a tetragonal cell with a = 4.445A and c = 8.908A. The density of the compound was determined and the number of atoms per cell (six atoms) was calculated. The X-ray density reported was 12.35 g per cu cm. The compound UsBir was treated in a similar way and it was reported to have a cubic structure 9.35A on an edge and to contain 28 atoms per cell. The density was given as 12.59 g per cu cm. Teitel reported that there was a compound UaBi, and no UBi, compound. (The difference in the compositions is 3.3 pct U.) This conclusion was based upon the extrapolation of some 20 tie lines in the

Jan 1, 1958

By W. W. Smeltzer

The linear formation rates of wustite films have been determined over the temperature range 590° to 1030°C using a vacuum microbalance technique. These rates are dependent directly on the partial pressure of carbon dioxide, Activation energies for film and scale formation in carbon dioxide and oxygen atmospheres are equivalent to either the dissociation energies of carbon dioxide and oxygen, or the activation energy for the diffusion of cation vacancies in wustite. Of the metals, iron is the most widely used basic constituent of durable alloys despite its intrinsic property of converting at a relatively rapid rate to the oxides from which it is derived. This property has accounted partially for many investigations on the oxidation of iron at low and high temperatures. Interpretation of the results have been complicated by formation of multilayers containing the various oxide phases. To aid in elucidation of the oxidation kinetics, measurements have been carried out in this investigation on the growth of the wustite surface layer. There are several studies directly related to the objective of this investigation. The growth of multilayer scales has been demonstrated to be diffusion controlled in oxygen at atmospheric pressure over the temperature range 450" to 1200°C by Davies, Simnad, and Birchenall.' To gain an insight into the diffusion mechanism, Himmel, Mehl, and ~irchenall' determined the self-diffusion coefficients of iron in wustite, magnetite, and hematite. These results were used to evaluate the oxidation rates of iron and its oxides, taking as a basis the theoretical parabolic rate equation developed by Wagner., The evaluations were compared to experimental data and were shown to provide essential confirmation of this theory. Fischbeck, Neundeubel, and salzer4 have demonstrated that the oxidation of iron in carbon dioxide and other atmospheres at high temperature obeys a linear relationship. Because the Arrhenius temperature coefficients of the reaction rate constants changed at the A, point they concluded that the passage of iron into the oxide controlled the reaction. This viewpoint has been accepted by Benard and ~albot' to explain the occurrence of linear rates in oxygen before the onset of diffusion-controlled parabolic oxidation. This basic premise of a rate-controlling reaction at the iron/oxide interface has been questioned recently by Hauffe and Pfeiffer.' Since the formation of wustite may follow a linear or parabolic relationship depending on the pressure of the gaseous re-actant, they propose that linear oxidation is determined by a chemisorption reaction while parabolic oxidation is controlled by diffusion. As confirmation of this viewpoint, Hauffe and pfeiffer6 and Pfeiffer and ~aubmeyer' have established that the linear scaling constants of wustite formation at 1000°C in carbon-dioxide or low-pressure oxygen atmospheres

Jan 1, 1961

By Leonard D. Jaffe, Donald C. Buffum

THE importance of temper brittleness in alloy steels has long been realized in Europe, In the United States recognition of its importance has developed within the last several years. Many brittle failures encountered in parts made of alloy steel are undoubtedly attributable, wholly or in part, to temper brittleness. These failures have occurred particularly at low temperatures, under shock loading, and in the presence of notches, restraints and combined stresses. It has been almost universally accepted that plain carbon steels are not susceptible to temper brittleness. As a result, considerable effort has been expended in attempts to discover the manner in which alloying elements introduce temper brittleness. It is desired to raise the possibility that plain carbon steels are not only susceptible to temper brittleness, but are much more susceptible than alloy steels, in the sense that they embrittle much more rapidly. It is suggested that previous views, (that plain carbon steels are not susceptible), are based upon an erroneous interpretation of the experimental results. INTERPRETATION OF PREVIOUS DATA For many years the standard criterion for susceptibility of a steel to temper brittleness consisted of comparison of the energy absorption, in a notched-bar impact test at room temperature, of specimens that had received two heat treatments.1 One specimen (or group of specimens) was quenched, tempered, and quenched from the temper. The other specimen (or group) differed only in having received an embrittlement treatment, which might consist of a slow cool from the tempering temperature, or of an isothermal hold in the range 450-550°C subsequent to quenching from the temper. If the energy absorption of the specimen receiving the embrittlement treatment was lower than that of the specimen not given this treatment, it was said that the steel was susceptible to temper brittleness, If the energy absorptions were the same, it was said that the steel was not susceptible. Several investigators2,3 found that plain carbon steels showed negligible difference in energy absorption in such tests (at least when their manganese content was below 0.60 pct), and concluded that plain carbon steels are not susceptible to temper brittleness. Recently the deficiencies of the criterion mentioned above have been pointed out.4-6 The criterion now generally used for susceptibility to temper brittleness retains the heat treatments used in the earlier scheme, but instead of the notched-bar impact tests being made only at room temperature, they are made over a range of temperatures, covering the transition from ductile to brittle fracture, If the transition temperature of the specimens receiving the embrittlement treatment is higher than those

Jan 1, 1948

By A. Rosenzweig, M. M. Karnowsky

The generalized binary diagram of the Au-Sn-Pb system is presented. The chief characteristic is the pseudobinary between lead and AuSn. On the high-gold side of the pseudobinary, four reaction isotherms were found at 363°, 274°, 225°, and 204°C. On the low-gold side of the pseudobinary, three reaction isotherms at 277°, 205°, and 176°C were found. A vertical section from the eutectic solder composition to gold was developed from the isothermal sections generated. METALLURGICAL problems arising from the intentional or accidental formation of Au-Sn-Pb alloys in soldering applications have indicated a need for information on the phase equilibria in this ternary system. The literature indicates that a complete diagram presenting this information has not been prepared. Even the recent excellent work by prince' entitled "The Au-Pb-Sn Ternary System" actually extends only to the AuSn or 50 at. pct Au range. There are more events in the 50 to 100 at. pct Au than in the less than 50 at. pct range. This article by Prince furnished much guidance in preparing this report. Initial efforts with the isopleth from the eutectic solder composition 61.9 wt pct Sn-38.1 wt pct Pb and 0 to 90 wt pct Au indicated that extensions of the work to the whole of the diagram (even if in less detail) were necessary to understand this system. In undertaking the construction of such a diagram, this study used differential thermal analyses (DTA) and metallography with verification and identification of phases by electron microprobe analyses. EXPERIMENTAL PROCEDURE The procedure began with the development of a cell which would be unreactive with lead, tin, and gold, retain its strength to 1100°C, exclude oxygen, and also furnish a suitable well for insertion and protection of a thermocouple to monitor temperature changes in the material. Such a cell would make it possible to reuse the sample should a repetition of determination be desired. Fig. 1 is a photograph of two such quartz cells as finally developed. The specimens have been run many times. The cell is made up of an inner sample bucket and an outer capsule with a thermocouple well which the sample surrounds. The DTA unit was an assembly devised from available instrumentation. The sample holder was a 3-in.-long cylinder of nickel, 2 1/2 in. in diam, fitted securely in a vertical tube furnace. Two holes 7/8 in. in diam were symmetrically located to receive the quartz cells. A dummy cell with nickel powder was used as the reference. The absolute temperature was recorded with a Pt/Pt 10-pct Rh thermocouple with an automatic Kaye ice bath compensator. (Calibration indicated the compensator to be accurate to better than ±0.5° over the 100° to 1000°C range.) The absolute temperature was measured in the sample and recorded on an L&N mul-tirange recorder with a full-scale display of 1 mv and automatic ranging of 99 mv. The differential signal between the sample temperature and the reference temperature was amplified with an L&N microvolt amplifier and recorded on an L&N Speedomax G recorder. Since two charts were obtained, the chart speeds were equalized and each event was noted on the differential chart, and the temperature at that time was obtained from the temperature record.

Jan 1, 1969

Discussion of the paper of CHARLES H. MACDOWELL, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 103 to 114. GEORGE S. RICE, Pittsburgh, Pa.-I am especially interested in the mining side of this important question. In 1911, when in Europe investigating mining matters, giving special attention to subsidence clue to mining, for there is a very big problem of that kind, as many of you know, in the Pennsylvania anthracite region, I visited Stassfurt, which is one of the chief centers of potash mining, and which was pointed out as the place to see surface subsidence. We found the town much askewsome of the streets having sunk from 15 to 30 ft., leaving many ancient buildings pitching at various angles. One old church, 500 or 600 years old, has been sunk about 20 ft., cracking it badly. I understand that this condition came about because in early mining clays they were careless about leaving proper supports and used no filling or packing. The Stassfurt mines work along a buried anticline the sides of which pitch at 45° on the average. Through this careless mining they had a break of the hanging wall which let in water from the overlying marls and sands. The water rapidly dissolved the salts in the pillars, and spreading through the entire chain of mines, caused their complete loss, with serious trouble for the old city. They had to start new mines some distance away, and take care to prevent roof caves. The packing system is of interest. They were driving large rooms into the rock-salt foot wall and using the rock salt as dry filling. The application of hydraulic filling, using a saturated solution, was under contemplation at some plant nearby. Whether 6r not the plan was carried out I do not know. I was reminded of the plan by Mr. MacDowell's remarking on the use of a saturated salt solution in the core drilling. His reference to the apparent breakdown of the potash syndicate raises an interesting question. We have had the German system of syndicates pointed out as perhaps one means of solving our troubles in the soft-coal mining industry due to overproduction. It seems to have worked out admirably in the case of the Westphalian coal-mining syndicate and also in the syndicate of Upper Silesia; but apparently the syndicate plan did not work in the potash industry. .

Jan 5, 1915

By F. Weinberg, E. H. McLaren

Dilute binary alloys have been solidified under controlled thermal conditions, and solute distributions, temperatures during freezing and melting, and the position and morphology of the solid-liquid interfaces have been examined. Binary Zn, Sn, and Pb based alloys were investigated with solute additions of AgU°, AU°, Sb'24, TlZo4, snH3, and Zns5. Approximately 150 cc of metal was used in each ingot. Appreciable solute segregation occurred in most of the ingots, depending on the solute concentrations, distribution coefficients. and freezing conditions of the alloys. Measurements were made of the general solute distribution by sectioning layers of material from the ingot circumference and counting the activity of each layer. Local segregation was detected by autoradiographic techniques. Freezing and melting curves for the same alloys were obtained by precision resistance thermometry. These curves are related to the corresponding measured solute distribution curves and those calculated from theoretical expressions. The position and morphology of solid-liquid interfaces during freezing were determined by both decanting and quenching techniques. The results indicate the manner in which freezing and remelting occurred under the conditions investigated. If an isomorphous dilute binary alloy is solidified or melted under equilibrium conditions, the concentration of solute in both solid and liquid would be uniform at all stages in the freezing process. The solute concentrations during freezing could be determined from the phase diagram of the alloy, and the freezing curves would have an alloy slope defined by the solidus and liquidus points. In practice, however, solidification under equilibrium conditions rarely, if ever, occurs, primarily because of low rates of diffusion in the solid and incomplete mixing in the liquid. As a result, the solute distribution and the shape of the freezing and melting curves obtained in a given system depends on a number of factors. These include, in addition to the extent of diffusion and mixing, the initial solute distribution and concentration, the distribution coefficient, the rate of freezing or melting, supercooling of the liquid, the morphology of the solid-liquid interface, and the effect of annealing. The purpose of the present investigation was to determine, experimentally, actual solute distributions and thermal curves for a series of dilute binary alloys, using tracer techniques to determine the solute distributions and precision resistance thermometry for the temperature measurements. In addition, observations were made of the positions and morphologies of the solid-liquid interfaces during freezing and remelting. The distribution of solute in a dilute alloy, assuming complete mixing in the liquid, and negligible diffusion in the solid, is given by1 where Co is the mean solute concentration of the alloy, C, is the solute concentration in the solidg is the fraction of the ingot solidified, and ko is the equilibrium solute distribution coefficient (assumed to be independent of concentration for dilute alloys). For the case of partial mixing, ko can be replaced by an effective distribution coefficient k. If solute transport in the liquid is assumed to be entirely due to diffusion, with negligible diffusion in the solid, then the solute distribution in the solid is given by Tiller et a1.' as where R is the rate of advance of the solid-liquid interface, D is the solute diffusion coefficient in the liquid, and x is the position of the interface from the start of freezing. The temperature at the interface TI is related to the solute concentration of the solid at the interface C, by the expression where Tm is the freezing temperature of the pure solvent and ml is the slope of the liquidus for the binary alloy being considered. Accordingly, by relating TL to the actual temperatures measured in the present experiments, solute distributions can be deduced from the temperature measurements. Using the above expressions, the measured solute distribution of a given alloy may be compared to the theoretical distributions, as well as to the distribution calculated from the observed freezing curve. EXPERIMENTAL The solvent materials used in making up the binary alloys were C. P. New Jersey zinc (99.999 pct), Vulcan Extra Pure Tin (99.999 pet), and Tadanac lead (99.998 pct). The solute elements were of 99.99 pct purity or better, and were activated in the

Jan 1, 1963

By C. F. Weinaug

In recent years, several methods have been proposed for correlation of physical properties and behavior of hydrocarbon systems. These correlations were found to be unsatis. factory for predicting differential gas liberation and shrinkage data now obtained experimentally. To achieve the desired accuracy, methods were developed to adjust the correlations with two experimental pieces of data. The required data are the saturation pressure at reservoir temperature and the specific volume or density at these conditions. The saturation pressure is used to adjust the vapor-liquid equilibrium-ratio correlations. The density measurement is used to determine the apparent density of liquid methane. With these adjustments, differential gas liberation and shrinkage are predicted within the experimental error. EQUILIBRIUM RATIOS Equilibrium ratios published by the National Gas Assn. of America' were used as a basis for the calculation. The convergence pressure for the sample was determined by using a hypothetical binary system, with methane as one component and the remainder of the system lumped together to form the other component. For the critical temperature of the heavy constituent, the weight average of the critical temperatures of the ethane and heavier components was used. The correlation of pseudo-critical temperature, density and molecular weight of Matthews, Roland and Katzl was used in this calculation for the hexane and heavier fractions. Points for the critical properties of methane and the hypothetical heavy constituent were placed on a chart of the critical loci of hydrocarbon systems. A critical loci for the hypothetical binary system was drawn, and the critical pressure of this system was determined at the reservoir temperature. This critical pressure became the convergence pressure for which equilibrium ratios were read from the NGAA4 charts. The NGAA equilibrium constants for C, through C, were used for the C,; through C, fractions since they were separated on the bases of normal paraffin boiling points. The correlation of Hoffman, Crump and Hocott5 as used to estimate the equilibrium constant for the C fraction. The NGAA eauilibrium-ratio charts are based primarily on paraffin systems and have to be corrected for the presence of naphthenes and aromatics. The correlations in the literature proved too unsatisfactory for determining these corrections. EXperimental data, the saturation pressure, is used with the correlation of Soloman2 to make this adjustment. The correction factors of Soloman were cross-plotted so that the factors for ethane and heavier components were made a function of the factor for methane. a2 = 0.7927 at + 0.1646 .........(1) where a, = correction coefficient for for methane NGAA equilibrium ratio, and a2t = correction coefficient for ethane and heavier NGAA equilibrium ratios. This equation and the equation for the bubble point are solved simultaneously for the correction coefficients. The bubble-point equation is anKnXn = 1.0 . . . . (2) The equilibrium constant for the saturation pressure at reservoir temperature is used. This procedure not only corrects for the relative volatility between components, but also assures that the results will be directly related to the experimental saturation pressure. METHANE DENSITY After determining a set of equilibrium ratios, the apparent density of condensed methane at 60°F and 14.7 psia was estimated. This was found to be necessary because the correlations of Standing3 ere found to be unsatisfactory. The law of additive volumes was employed to make this calculation.

By R. P. Carreker, J. G. Leschen, J. H. Hollomon

The external appearance of a crystal which has undergone plastic flow suggests that adjacent blocks of the crystal have glided bodily past one another along the slip planes. However, the great discrepancy between the shear stresses calculated to effect such a movement and those actually observed has for many years stimulated searches for more satisfactory interpretations of the slip process. Appreciable success in these efforts has been realized by assuming the presence in the crystal of various sorts of imperfections and by considering the consequences of the presence of these flaws when stress is externally applied. The theory that has received the most attention recently—that of dislocations—postulates the occurrence of small, mobile imperfections or dislocations which move through the crystal along the slip direction, each dislocation being attended by a local shear displacement of one interatomic distance. Thus only that portion of the crystal through which the dislocation has passed may be said to have slipped. Since each dislocation produces a displacement of only one interatomic distance, an avalanche or train of many dislocations would be necessary to account for the observed displacements of several hundred or thousand interatomic distances. The salient point of the theory of dislocations is the concept that a slip band does not suddenly appear in its entirety. On the contrary, it grows progressively across the slip plane as the individual dislocations successively appear and advance in a train through the crystal. However, the concept of growth is not intrinsic only to the theory of dislocations, since atomistic mechanisms other than that postulated by the dislocation theory can quite probably also describe the growth of a slip band. For instance, a slip band might resemble a disc-like interface that appeared and then grew continuously from a small size, producing a displacement that increased with the size of the disc. Whatever the precise mechanism, the concept of growth is in itself consistent both with the observed low values of critical shear stress and with the experimental observation that slip bands frequently do not traverse the entire crystal. The likelihood that slip bands grow implies that they must first be nucleated and that the initiation of slip can therefore be analyzed in terms of the general concepts of nucleation. Indeed, this suggestion was advanced1 several years ago, but the matter does not appear to have been further pursued. Recent advances in the theory of nucleation 2,3,4 have encouraged such a treatment of the slip process. As will presently be demonstrated, this approach to the problem not only accounts successfully for the incubation periods that have been observed 5,6 to precede slip but also predicts certain transient effects in the deformation process. The existence of these transients apparently has not hitherto

Jan 1, 1949