Search Documents

By S. Grinsfelder

Although wildcatting was hampered by the general overproduction and low price of crude, several developments, worthy of note in the history of the petroleum industry in the Rocky Mountain region, were made in 1927. This district records production from six new fields, two of these having been heretofore productive of gas. Deeper pay horizons were found in two other oil fields. In order to facilitate transportation from fields, six new oil pipe lines were completed or in the course of construction at the end of the year, and one line is proposed for 1928. Four gas lines were completed, one was under construction, and one was proposed for 1928. The total production in 1927 in the Rocky Mountain district was 29,591,379 bbl.,' a decrease of 7,771,991 bbl., or 21 per cent., fro111 the previous year. This was occasioned by natural decline and the general curtailment of production and drilling. A review of the development by states follows. Colorado Production from horizons in the Morrison and Sundance at Craig and at Ilrs Dome, and the bringing in of the deepest producing well in the Rocky Mountain district on North McCalluin anticline (Waltlrn) in Jackson County are the outstanding developments for the year in Colorado. In March the Midwest Refining Co.'s Parkinson 21 SD, SW SE, Sec. 22 T p. 4 N R 92 W, Iles Domr, Moffat County Colorado, found gas in sands in the Morrison estimated at 15,000,000 cu. ft., and at 3242 ft. an oil sand was encountered in the Sundance. Initial production from this horizon was 2575 bbl. in this well. This structure previously was only productive of water in the sands of the Dakota group but has been producing shale oil from horizons in the Benton. The second well completed by the Midwest Refining Co., No. 18 SD in Sec. 23 was also productive of gas in the Morrison and made an initial of 300 bbl. from sands in the Sundance. By the end of the year three other wells wrrc nearing the completion stage but none of them indicate that they will be as big producers as the discovery. To date the productive area has

Jan 1, 1928

By Edwin R. Phelps, Charles W. Porterfield

BACKGROUND OF SURFACE MINING Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal were mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-year periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to in- crease. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu yd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu yd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining. 4) Surface mining normally recovers a much higher percentage of the coal reserve than can be recovered by underground mining. 5) Some coal measures can best be extracted by surface mining

Jan 1, 1981

Jan 9, 1951

By J. O. Glanville, L. H. Haley

Ice frozen from a dilute chemical solution is mechanically weaker than ice frozen from pure water. This phenomenon is the basis of a practical method for reducing the strength of a mass of frozen coal. If a chemical additive is applied to moist coal prior to its shipment during freezing weather, the resulting frozen coal can be more easily broken than in the absence of the chemical additive. This greatly expedites the unloading and handling of coal during winter. There has been considerable research into the nature and mechanical strength of ice frozen from various solutions. In this paper, literature relating to this process as well as literature relating to the chemical treatment of coal and mineral particulates is reviewed. Some important articles are discussed and speculations made about the nature of the ice-weakening process. A laboratory evaluation of the effects of chemical additives on the mechanical strength of ice and frozen coal has been made. An apparatus designed for this purpose is described, and some results obtained with it are discussed.

Jan 1, 1983

By W. O. Philbrook. K M Goldman, M. M. Helzel

RADIOACTIVE calcium has been used to learn whether calcium can be detected in iron saturated with carbon after it has been melted under CaO- A12O3- SiO2 slags similar to those used in the iron blast furnace. It was hoped that the radioactive tracer technique might make possible a general study of steelmaking reactions in which calcium or calcium oxide are involved. No calcium could be found in the metal under conditions which were favorable for the reduction of calcium, and it has been concluded that the calcium content of the iron was less than 6 x 10 - pct. Some of the problems encountered have been instructive with regard to pitfalls and limitations of tracer methods. Calcium oxide occurs in almost all iron- and steelmaking slags, and it is essential to the success of all commercial basic steelmaking processes. Calcium alloys are sometimes used in the deoxidation of steel and for the innoculation of gray iron. The element calcium is therefore almost as ubiquitous in the steel industry as are carbon and oxygen, but calcium has been thought to be completely immiscible with iron in both the liquid and the solid states.' It does not seem entirely unreasonable to Suppose, however, that some low concentration of calcium might exist in liquid iron under a basic slag with other conditions being favorable, just as silicon and other elements can be introduced into iron by reduction of their oxides from slags under appropriate circumstances. The radioactive tracer technique offered a more sensitive method than chemical analysis of testing this supposition. The reasons for interest in this investigation were strong enough to justify a recognized risk of failure. On the theoretical side, information on the distribution of calcium between liquid iron and a slag and the rate at which the equilibrium distribution is approached would contribute strongly to the general theory of slag-metal interface reactions. Furthermore, any evidence on the presence of calcium in liquid iron might provide a vital clue to the mechanism of the desulphurization of iron by slags. All of the reactions which have been proposed to explain desulphurization postulate that the sulphur ultimately becomes fixed in the slag as calcium sulphide, but the mechanism by which sulphur

Jan 1, 1951

By Edward H. Robie, E. J. Jr. Kennedy

his volume records the "clay symposium" that featured the geology side of the Annual Meeting of the Institute at St. Louis, February 19-22, 1951. The symposium consisted of four sessions held under the joint sponsorship of the Geology Subdivision and the Industrial Minerals Division AIME and the Society of Economic Geologists. Its main purpose was to define or outline certain problems of clay and laterite genesis, and the papers herein, which were presented at the first three sessions, deal for the most part with individual deposits or special problems. The fourth session was a seminar concerned almost wholly with a discussion of "problems." The discussion follows the papers in the volume. The clay symposium was not the work of an appointed committee. It was thought up and inspired by John J. Collins, who so ably supervised and co- ordinated the mining, geology, and geophysics program for the 1950 annual meeting of the Institute. After requesting Dr. A. F. Frederickson to get material together on clay and laterites for the St. Louis meeting, Mr. Collins visited Dr. Frederickson and discussed this project with him in greater detail. By that time their interest and enthusiasm had spread to others in the field. The Geology Subdivision, the Industrial Minerals Division, and the Society of Economic Geologists by common consent turned over the organization of the program to Dr. Frederickson. Mr. Collins continued in active touch with Dr. Frederickson and gave him every assistance. Dr. E. C. Harder and Dr. W. D. Keller read all the material comprising the symposium, and their comment was made available to Dr. Frederickson, who did much to put papers and discussion in final shape for publication. To the Karl Eilers Memorial Fund--one of the Funds that enables the Institute to publish books of this kind, to the authors of the various papers, to the contributors to the discussion, and to Messrs. Collins and Frederickson the Institute and readers of this book are indebted.

Jan 1, 1952

By Michael Perch, Charles C. Russell

Nearly 7 5 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1943

By Michael Perch, Charles C. Russell

Nearly 7 5 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1943

By W. S. Ayres

THE boiler from which these stay-bolts have just been obtained was that of the locomotive Catasauqua, Lehigh Valley Railroad, built at the company's shops, South Easton, Pa., in 1864. The iron is Lowmoor, and has been in use nearly ten years. The stay-bolts have become highly crystallized from some cause, and are very brittle, only requiring three blows of an ordinary machinist's hammer to break them. On the other hand, when annealed they are remarkably tough, as shown by the doubled sample. The majority of the broken bolts were found to be along the curve of the shell from a to c, Fig. 6. All of them were broken just inside the shell, and in no case next the fire-box. The fractures seen to have been of slow procedure, beginning at the top of the bolt, gradually working deeper and deeper until the pressure of steam overcame the tenacity of the remaining parts. Unequal contraction and expansion of the parts of the boiler seems in this case to be the only existing cause for a fracture. We cannot, from the data obtained, prove to an absolute certainty the manner in which the combined forces generated by the unequal contraction and expansion of the parts have arrived at their resultant work ; but we can, from these data and from existing circumstances, arrive at what seems to be a fair supposition, and thus at least anticipate the truth. The contraction and expansion in locomotive boilers has a large range between its extremes, and is very variable, both with reference to time and to their component parts. The shell and fire-box do not, perhaps, at any time, contract and expand at the same rate, nor proportionally ; but, on the contrary, owing to the great changes in temperature that take place both in the atmosphere around the shell, and in the fire in the fire-box, their condition is often changed suddenly, and widely from that which they just previously had. This racking tendency produces strains in the different parts, and it is fair to suppose that the continual motion of the two

Jan 1, 1874

By W. S. Ayres

The boiler from which these stay-bolts have just been obtained was that of the locomotive Catasauqtia, Lehigh Valley Railroad, built at the company's shops, South Easton, Pa., in 1864. The iron is Lowmoor, and has been in use nearly ten years. The stay-bolts have become highly crystallized from some cause, and are very brittle, only requiring three blows of an ordinary machinist's hammer to break them. On the other hand, when annealed they are remarkably tough, as shown by the doubled sample. The majority of the broken bolts were found to be along the curve of the shell from a to c, Fig. 6. All of them were broken just inside the shell, and in no case next the fire-box. The fractures seem to have been of slow procedure, beginning at the top of the bolt, gradually working deeper and deeper until the pressure of steam overcame the tenacity of the remaining parts. Unequal contraction and expansion of the parts of the boiler seems in this case to be the only existing cause for a fracture. We cannot, from the data obtained, prove to an absolute certainty the manner in which the combined forces generated by the unequal contraction and expansion of the parts have arrived at their resultant work ; but we can, from these data and from existing circumstances, arrive at what seems to be a fair supposition, and thus at least anticipate the truth. The contraction and expansion in locomotive boilers has a large range between its extremes, and is very variable, both with reference to time and to their component parts. The shell and fire-box do not, perhaps, at any time, contract and expand at the same rate, nor proportionally; but, on the contrary, owing to the great changes in temperature that take place both in the atmosphere around the shell, and in the fire in the fire-box, their condition is often changed suddenly, and widely from that which they just previously had. This racking tendency produces strains in the different parts, and it is fair to suppose that the continual motion of the two

By L. W. Holm

Laboratory flooding experiments on linear flow systerns indicated that high oil displacement, approaching that obtained from completely miscible solvents, can be attained by injecting a small slug of carbon dioxide into a reservoir and driving it with plain or carbonated water. Data are presented in this paper which show the results of laboratory work designed to evaluate this oil recovery process, particularly at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi. Under these conditions CO2 exists as a dense single-phase fluid. It was found that a bank, rich in light hydrocarbons, was formed at the leading edge of the CO? slug during floods on long cores. Formation of this bank is probably due to a selective extraction by the C02 and, it is believed, partially accounts for the attractively high oil recoveries. In crddition to the efficient displacernerlt of oil from the pores of the rock by this process, the favorable rnobility ratio related to a C0 2-water flood also contributes to high oil recovery. A further advantage of this process is noted on limestone and dolomite rock, in that the CO1 reacts with the porous medium increasing its permeability. Flooding experiments were conducted on sandstone and vugular dolomite models. The results of this experimental work show the effect on oil recovery of type of porous medium, pore geometry, flooding length, and flooding pressure. The porosity of the cores and rilodels varied from 16 to 21 per cent and their pern~eabilities ranged from 100 to 200 md. A reconstituted West Texas reservoir oil, a West Texas stock tank oil, an East Texas stock tank oil and Soltrol were used to represent reservoir oils in this study. Oil recoveries ranging from 60 to 80 per cent of the original oil in place in these cores were obtained by CO2,-carbonated water floods at pressures between 900 and 1,800 psi, compared with conventional solution gas drive and water-flood recoveries of 30 to 45 per cent on the same cores. Oil recoveries greater than 80 per cent resulted frorn f1oods at pressures above about 1.800 psi. There high recoveries were noted from both the sandstone and the irregular Porosity carbonate cores. In all floods, additional oil was recovered by a solutiorr gas drive resulting from blowdown following the flood. Oil recoveries of 6 to 15 per cent of the original oil in place were obtained during this blowdown period. This additional recovery was found to be a function of oil remaining after the flood, decreasing with decreasing oil saturation. It was also noted that highest oil recoveries by blowdown were obtained when carborlated water rather than plain water followed the CO, slug. INTRODUCTION Miscible phase or solvent flooding processes, which are designed to increase oil recovery -from petroleum reservoirs, involve the injection of small quantities of a petroleum solvent into the reservoir, followed by an inexpensive scavenging fluid which is miscible with the solvent. Essentially complete displacement of oil from the pores of reservoir rock has been obtained by this technique. CO,, although not completely miscible with most reservoir oils at moderate pressures, is highly soluble in these oils at pressures above about 700 psi; there is appreciable swelling and reduction in the viscosity of oil when CO, is dissolved in it. Therefore, CO, could be expected to perform similarly to other oil solvents as a displacing agent. CO, is also highly soluble in water at elevated pressures, so water should be a satisfactory material to drive a slug of CO, through an oil-bearing reservoir. A favorable mobility ratio would be obtained through the reduction in viscosity of the oil and the use of water as a final displacing agent. A number of investigations of the use of CO, to improve oil recovery have been reported in the literature.2,3,4,5,6 These studies, however, have been conducted on uniform porosity sandstone at relatively low temperatures and pressures. The behavior of CO1 as a flooding agent at temperatures above its critical temperature could not be predicted adequately from these studies, particularly for the case of non-homogeneous rock. The purpose of this work was to evaluate the oil recovery efficiency of a process involving the injection of a CO2 slug followed by carbonated water, at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi, and to compare this process with conventional water flooding. The investigations were primarily designed to provide information on the efficiency of the process in irregular porosity carbonate rock. The effects of flooding path length, the presence of free gas, the type of oil to be recovered, and the amount of solvent required were also determined. The essential results of static phase behavior studies and experimen-

Elected Died 1895 ABBOTT, AI ATTHUR 1908 1882 ABBOTT, ARTHUR V 1906 1905 ABE, MASAYOSHI 1909 1903 ADAMS, CHARLES C. 1905 1906 ADAMS, JOHN C. 1913 1905 ADAMS, WILLAMS 1909 1903 ADAMS, W. EDWARDS 1910 1884 ADDY, MATTHEW 1896 1906 AFFLECK, WILLIAM A. 1911 1889 AKERS, WILLIAMS A. 1906 1905 ALABASTER, RUPPERT C. 1911 1899 ALBERGER, LOUIS R. 1911 1894 ALLEN R B 1896 1905 ALLEN, R. SCOTT 1906 1886 ALLISON, ROBERT 1916 1874 AMIOT, H. 1892 1886 AMSLER, CARL 1894 1898 ANDRSON, JOHN W 1905 1895 ÅNGSTROM, CARL 1901 1887 ARCHBALD, JAMES 1910 1900 ARLETT, GEORGE H 1906 1895 ARMSTRONG, JOHN F 1898 1905 ARNOLDS, LEO F. 1917 1882 ARNOLDS, HUGO 1886 1875 ASHBURNER, CHARLES A 1889 1872 ASIIBURNER, WILLIAM 1887 1883 ATKINS, C M , JR 1885

Jan 1, 1923

By D. A. Martin, Laird Crocker, W. I. Nissen

The Federal Bureau of Mines has developed a process for removing SO2 from stack gases. The process comprises absorption of SO2 in an. aqueous solution of sodium citrate, citric acid, and sodium thiosulfate, followed by reaction of the absorbed SO2 with H2S to precipitate sulfur and regenerate the citrate solution for recycle. A pilot plant was operated at The Bunker Hill Co. lead smelter in Kellogg, Idaho, to assess the feasibility of using the process for flue gas desulfurization. Nominal capacity of the pilot plant, which treated .tail gas from the lead smelter sintering furnace, was 1699 standard meters cubed per hour (15 degrees celsius) of 0.3- to 0.7-percent-SO2 gas yielding about 272 net kilograms of sulfur per day. The pilot plant was operated for about 4500 hours and produced more than 45 net tonnes of sulfur. The operation demonstrated that (1) more than 95 percent of the SO2 could be removed from the lead smelter sintering furnace tail gases, (2) regeneration of the citrate solution with H2S and precipitation of sulfur in conventional stirred vessels was readily controlled and highly efficient, (3) the precipitated sulfur could be continuously recovered as a 99.5-percent-pure product by kerosine flotation and melting, and (4) the 77- to 79-percent-H2S gas used for sulfur precipitation could be readily produced from pilot plant product sulfur, natural gas, and steam. Projected operating costs, including capital charges, for a citrate plant, installed at a 118 000-tonne-per-year lead smelter and treating 49 271 standard meters cubed per hour of lead smelter sintering furnace tail gas, are estimated to be $384 per tonne of sulfur.

Jan 1, 1976

Jan 1, 1949

By Oliver Bowles

Dimension stone is a term applied to stone sold in blocks or slabs of specified shapes and usually of specified sizes, contrasted with crushed, broken and pulverized stone covered in another chapter. Dimension stone includes cut stone, rough building stone, ashlar,* rubble, monumental stone, paving blocks, curbing, flagging, and many types of ornaments and novelties carved from stone. Riprap-large, irregular blocks used for shore protection-is classed with crushed and broken stone. Composition, Varieties, and Properties Dimension stones are of many kinds. The principal varieties are granites, trap rock (diabase, basalt, and gabbro), sandstone, limestone, and marble. Slate is covered in a separate chapter. Granite is a visibly granular crystalline rock consisting essentially of feldspar, quartz, and mica or hornblende. The basaltic rocks are darker in color than the granites. They contain little or no quartz and consist largely of plagioclase feldspar, augite, pyroxene, and hornblende. They are classed commercially as black granites. Limestone consists essentially of calcium carbonate. Dolomites and magnesian limestones used as dimension stone are classed with the high-calcium limestones. Marble is a crystalline form of limestone, but in the trade, any carbonate rock which will take a polish is called a marble. Many limestones which are fossiliferous but which will take a polish are sold as a decorative stone for lobbies of hotels and office buildings. Sandstone consists essentially of silica in the form of sand grains cemented into a coherent mass. Although rock occurrences are numerous and widespread, the exacting requirements of use condemn all but a small fraction of them for commercial use as dimension stone. No deposit that has closely spaced joints or planes of weakness can be used because sound blocks of moderate to large size are demanded. Uniform texture and grain size, constant and attractive colors or color pattern, and freedom from impurities that may cause stains or deterioration usually are demanded. Hardness is a variable property. Granites and diabases are as hard as or harder than steel, while limestones and marbles may be scratched with a knife. The hardness of sandstone depends upon the degree of cohesion of the grains. Workability depends to a considerable extent on hardness, but the degree of hardness has little influence on use except where stones are subjected to abrasion as on steps or floors. "Texture" as applied to stone relates to the arrangement, uniformity, and size of the constituent grains. Stones are of many colors and thus can satisfy a variety of tastes. For monumental stone, a marked contrast between polished and tooled surfaces is preferred in order that inscriptions may be read easily. Strength requirements usually may be disregarded because any sound structural stone suitable in other respects is almost invariably many times as strong as would be required for any ordinary use. The pressure on the base course of the Washington Monument, Washington, D. C., is less than 700 psi, and highgrade granites, limestones, sandstones, and marbles will sustain a crushing load of 10,000 to 25,000 psi. A structure made of stone with a crushing strength of 15,000 psi would have to be nearly 21h miles high before crushing of the lower courses would occur. However, stone disintegrates more readily under severe

Jan 1, 1960

By C. Stansfield Hitchen

The paper describes the application of the logarithmic wedge sector method of quantitative spectrography to the estimation of commonly occurring minor impurities in crude and refined tin. Both arc and spark methods of emission were employed and with the former a new device was used to overcome difficulties arising from the low melting point of the metal. The impurities investigated included antimony, arsenic, bismuth, copper, iron, lead, and zinc, their concentrations lying, in general, between 0.01 and 0.50 per cent. The results obtained show that the method may be usefully employed for the estimation of bismuth, copper, iron, lead, and zinc, in amounts ranging from 0.50 per cent to well below 0.01 per cent. Arsenic and antimony, however, could not be estimated in amounts less than 0.03 and 0.07 per cent respectively. Out of a total of 116 estimations by arc and spark emission, in 96 the errors were less than 5 per cent of the total quantity of the element present, whereas in the remaining twenty, the errors lay between 5 and 25 per cent. Spectro-analytical data for the several impurities studied are given in the form of tables, and curves correlating line-intensity with concentration have also been included. DISCUSSION (R. G. Waltenberg presiding) D. M. Smith, London, England (written discussion).—I am interested in Dr Hitchen's account of his investigations on the application of spectrographic methods to the assay of tin and congratulate him on his valuable contribution to the literature on the subject of quantitative spectrum analysis. Some of the results obtained in the course of investigations carried out for the British Non-Ferrous Metals Research Assn., although obtained under somewhat different experimental conditions, may be of interest in connection with this paper. Arc and spark spectra of standard samples of tin containing various known amounts of antimony, bismuth, cadmium, copper, lead, silver and arsenic have been investi-

Jan 1, 1933

By F. L. Bosqui

A. L. BlomFIeld, Denver, Col. (communication to the Secretary.*) — Mr. Caldecott says on p. 67: "The Dorr thickener shown, while a useful device when crushing with cyanide solution for removing surplus solution from slime pulp prior to air-lift agitation or vacuum filtration, is not adapted to effect as complete a separation of water from settled slime as the ordinary intermittent settlement and decantation." This statement might have passed muster in this country several years ago when. the Dorr thickener was a new device, but its use in hundreds of mills in the United States has demonstrated that as thick a product is being discharged from it as was obtained from the intermittent settling which it has supplanted. • It is interesting to note that recent investigation, especially the work of 11. 6. Coe and G. H. Cleveilger,' in the March Bulletin of the Institute, under the title: Laboratory Method for Determining the Capacities of Slime Settling Tanks, has developed the general theory of settlement and explains the results obtained in practice. Just as free settlement is a function of surface area, so thickening after the zone of free settlement is passed is a function of time. The time required is obtained by the capacity or volume provided in the settler for this thickening zone. Each pulp is a problem in itself, both in regard to free settlement and to time required to reach a commercially finished thickness. Some pulps require 48 hr. and more to reach a density of 40 per cent. solids; others no coarser to the screen test reach a density of 65 per cent.' solids in a fraction of that time. In thickening any pulp a point is reached where the increase in density is so slow as to be commercially unprofitable. When any part of the pulp has reached this point it should pass on for treatment—its place in the thickener should be occupied by pulp which has not yet reached the commercial limit. By doing this the whole volume of the settling tank is kept in active use. Thus the continuous thickener keeps the whole tank at work to its commercial limit, while the intermittent settler has much of its volume occupied at times by pulp which is either quite finished thickening or at least thickened past the commercial point. The mechanical efficiency of the continuous thickener can be the only argument for limiting this statement. In my own experience I have never

Jan 1, 1916

By W. D. Ludemann, J. E. Dor, L. A. Shepard

Recovery of the creep resistance of 99.99 pct pure Al was studied at temperatures 540°, 573°, 600°, and 611°K. Poly-crystalline specimens crept under a stress of 950 psi to a strain of 5.5 pct were allowed to recover for periods of from 1 min to 16 days under a residual stress of 4.4 psi. Increased creep rates upon reapplication of the 950 psi stress evidenced softening of the material. The activation energy for the recovery process was found to be 64,000 cal-per mol. THREE major observations have clearly revealed that the creep of polycrystalline aluminum above about 510°K is controlled by the rate of climb of jogged edge components of dislocations past the barriers impeding their motion: 1) Extensive polygonization, characteristic of climb, takes place during creep.'9' 2) The activation energy for creep equals the estimated activation for self-diffusion. 3) The stress law for creep coincides with theoretical predictions based on the climb mechanism.4,5 The decreasing rate during the primary stage of creep must be ascribed to the introduction of additional barriers to the glide of dislocations. During secondary creep the density of barriers must remain constant, the rate at which new barriers are formed being equal to the rate at which they recover. For this reason the nature of the barriers, and their rates of formation and recovery, are significant to a complete understanding of creep. It is proposed here to study the kinetics of the recovery of barriers to creep of high-purity polycrystalline aluminum in the climb range. The technique will consist of creeping a series of tensile specimens under a prescribed stress to given state following which the specimens will be recovered for various times and temperatures under approximately zero stress. The amount of recovery will be determined by comparing creep curves following the recovery. EXPERIMENTAL PROCEDURE The material used for this investigation was a 99.99 pct pure Al supplied by the Aluminum Co. of America in sheets of 0.001-in. thickness having an H-18 temper. The spectroscopic analysis of impurities gave Cu-0.004 wt pct, Fe-0.002 pct, Si-0.001 pct, others-0.000 pct. Creep specimens were machined with their tensile axes in the rolling direction of the sheets. Annealing in a molten potassium nitrate-potassium nitrite bath for 1 hr at 686K, followed by air-cooling, resulted in a grain diameter of from 0.22 to 0.27 mm. Creep machines were equipped with constant stress lever arms of the type suggested by Fullman, Carreker, and Fishher,' which maintained the applied stress to within 0.04 pct of the reported value of 950 psi. Creep strains were calculated from extensions over a 6-in. gage section to the nearest 3 X 10"5. The temperatures of testing, 540°, 573", 600°, and 611°K, were obtained by immersing the specimen and extensometer assembly in a molten KNO2-KNO3 bath. Temperatures during the periods of creeping could be maintained constant to within better than ± 1°K. Correlation of creep data at different temperatures of testing demanded the use of an appropriate temperature-compensated time 8. Previous investigations have shown that the creep of pure metals at temperatures above about 0.55 of their melting temperatures can be correlated by the functional relationship3" e=f(0), s= const. [1] where e = total plastic strain during creep f = a function that depends on stress a = stress 6 = te-Q/RT = a temperature-compensated time t = time under test Q = 35,500 cal per mol = activation energy for creep R = gas constant, and T = absolute temperature In the present series of tests all of the creep was conducted under the same stress of 950 psi. To provide identical initial conditions for the recovery all specimens were first crept to a temperature-compensated time of = 47 X 10-14 min which resulted in a creep strain of 0.055 + 0.005 regardless of the creep temperature. During recovery, a small stress (4.4 psi) was permitted to remain upon the specimens to maintain tautness in the pulling assembly and to prevent mechanical damage to the soft specimen. After each recovery period, the full stress was reapplied and

Jan 1, 1961

By E. P. Klier, V. Weiss

IN studies of the X-ray diffraction line geometry of iron with chromium radiation using techniques aimed at minimizing the background intensity, Kp and Ka emission satellites* were resolved with three techniques. These satellite lines are present with sufficient intensity to lead potentially to erroneous structure analysis, if not properly interpreted. The techniques used were: 1) film technique with un-filtered radiation and polycrystalline specimen, 2) film technique with unfiltered radiation and single crystal, and 3) counter technique with unfiltered radiation and single crystal. An example of results obtained with technique 1 is given in Fig. 1.

Jan 1, 1958

Jan 1, 1890