Search Documents

By I. A. Lesk

The various materials utilized in the construction of integrated circuits, and the resultant materials interfaces, are discussed with emphasis on a materials system that is compatible with all types of integrated circuits and minimizes the number of different interfaces. Problems with interfaces may originate in the silicon, on its surface, and between other materials within the integrated-circuit package independent of the silicon. ThE difference between integrated-circuit theory and practice may generally be spelled out in terms of the difficulties in fabricating a desired structure. There are, of course, problems in forming the requisite materials, of the necessary composition and geometry, where needed. A distinct class of problem, however, is associated with interfaces— generally between different materials, but occasionally between regions of the same material. We require that each interfacial system perform its proper electrical, mechanical, and thermal function, and do so in an unchanging manner with time under the most severe operating conditions. In a practical sense, we deal in nonideal systems, such that it is generally not possible to form an interface exactly the way it was intended, even if we allow for a knowledge of the practical limitations of the fabrication system. Another way of looking at this situation is to realize that, when we form a group of interfaces under apparently the same experimental conditions, there are often differences of important consequence between them. Very high-magnification pictures, such as are obtained by an electron microscope, reveal fine structure that often differs over the area of a given sample, as well as from sample to sample. Low-magnification pictures look better, but don't eliminate the problem. The trend towards integrated circuits, and away from circuits fabricated utilizing separate components, is very strong in many areas of electronics. A typical silicon monolithic integrated circuit, still in place in the wafer on which it was fabricated, is shown in Fig. 1. The increased reliability which is being experienced through the use of integrated circuits can, to a large extent, be credited to the reduced complexity of the interface system that is present in the electronic system. A glance at Fig. 1, however, with all of its epitaxial and diffused p-n junctions, and interconnect system, shows that interfaces have been far from eliminated. Fig. 2, depicting a schematic cross-sectional view of a (partial) typical integrated circuit, illustrates in detail the numerous interfaces that occur in this type of structure. Besides the individual circuit elements, there are interfaces for isolation, and, Fig. 3, even a crossover requires a series of interfaces. What has been accomplished, however, irrespective of whether or not the total number of interfaces in the circuit is increased or decreased, is that the variety of interfaces is very much reduced. This is because there are fewer materials involved. Since the expense incurred in an R & D program to improve reliability is pretty much directly proportional to the variety of interfaces involved, it is economically advisable to work with integrated circuits for highest reliability. That is not to say that circuits built using standard components could not be made as reliable as integrated circuits, but that the expense involved because of the more complex over-all interface system would be much greater. Although electronic performance utilizing integrated circuits with all silicon elements (i.e., transistors, diodes, resistors, capacitors) is adequate for many applications, there are numerous instances where thin-film passive elements must

Jan 1, 1965

By H. A. Wentworth

THE Huff electrostatic plant of the United States Smelting Company operated in conjunction with its wet concentrator at Midvale, Utah, was the second plant of substantial size installed using the Huff process, and the first plant to be put in operation on the so-called Western complex ores. In spite of the machinery being of early design and consequently embracing many of the mechanical weaknesses incident to a pioneer plant the mill has operated steadily and uniformly since the summer of 1909, about five years now, without any material change other than some re-arrangement of the machinery for better handling of the sizes. The ore, at present coming almost entirely. from the company's mines in Bingham, is of practically the same composition as that upon which the plant was first put in operation. The crude ore, consisting of the sulphides of copper, lead, zinc, and iron, and containing small amounts of gold and silver, is brought by train and delivered to the hoppers of the wet concentrator, where by jig and table treatment, there are produced a shipping lead concentrate, a tailing and a middling product, the latter being conveyed in push cars to the adjoining electrostatic mill. The crude ore delivered to the wet concentrator contains from 6 to 9.5 per cent. zinc. At times the plant is used also for the treatment of custom ores from the Bingham district and elsewhere, and at such times the results of the plant vary according to the material in use, but as by far the larger portion of the product is that from the company's own mines, the results given below are fairly indicative of the general work obtained. The accompanying diagram illustrates graphically the flow of the ore through the electrostatic mill. The middling coming from the wet mill containing from 15 to 18 per cent. moisture is hoisted while on the cars by an elevator, and delivered from the top of the elevator to a hopper over the drier. The drier first installed was of too low capacity to take care of the moisture present in the tonnage to which the mill was later

Jan 8, 1914

By Clarence A. Seyler

The technical difficulties of cutting thin sections of coal for examination by transmitted light have hitherto restricted the investigation of the important subject of the microstructure of coal to the few possessed of the requisite skill and time. Apart from this, the method fails with anthracites and other coals rich in carbon, owing to the opacity of the material. Occasional use of the method of polishing a surface, with or without etching, has been made, but it was not until Winter' published an account of his results that attention was seriously directed to the method. In May, 1923, a specimen of dull anthracite came into my hands; I tried Winter's method on it and the presence of megaspores and other vegetable structures became clearly visible. A preliminary notice was published by me;2 but I soon abandoned the use of Schulze's solution, having found that a mixture of chromic and sulfuric acids gave far better results. In the meantime Turner and Randall, in America, had independently developed the method of flame etching, as applied to anthracite, with great success. I have spent a year studying the method of chromic etching, which gives excellent results with bituminous coals and camels, as well as with anthracite. For anthracites, I have used the chromic method and Turner's method of flame etching, whichever was the more convenient or as a check one on the other. The polishing is done, according to metallurgical practice, by the use of a polishing machine and successively finer emery paper, followed by polishing on cloth moistened with a suspension of levigated green oxide of chromium, and a final rubbing on "selvyt" (a cotton velvet polishing cloth) moistened with alcohol. The polished sample is examined by reflected light with a 2/3 and 1/6 in. objective. Bituminous coals usually show considerable structure, and even anthracites show it faintly in places. The sample is then etched by immersion in a boiling solution made by adding 10 c.c. of concentrated sulfuric acid to 30 C.C. of a saturated solution of chromic acid; enough water is then added to dissolve

Jan 1, 1925

By E. P. Mathewson

THE experiments described in this paper were made at the Washoe Reduction Works, Anaconda, Mont., for the purpose of determining the relative speed of elimination of the iron, sulphur and arsenic during the process of bessemerizing copper-mattes. The samples were taken from a horizontal "barrel" converter, 8 ft. in diameter and 12 ft. 6 in. long, having an average charge of 9 tons of matte, and blown with a 16-1b. air-pressure. All samples were taken with the blast on, turning the converter from its normal blowing-position to nearly verti¬cal, so that a conical mold, with a long handle attached to a horizontal rod, could be introduced from a platform above the converter into the mouth of the converter and a sample taken. The difficulties of taking a sample with the blast on are appar¬ent, and the irregularities of the lines in Figs. 1, 2 and 3 can be readily accounted for by the amount of slag in the samples. On the whole, the plotting of the results gives comparatively uniform lines, considering the conditions. The samples were taken by the regular sampling-force of the works at 10-min. intervals, as shown in Tables I., II and III, which also give the chemical analysis of the samples so taken. The test shown in Table I. was made with a new converter; that of Table II with a converter that had made three charges and had been cleaned out; that of Table III with a converter that bad blown one charge to white metal, and had then been " washed " out and used for the test. In plotting these results, it was necessary to take, as a basis, the percentage of copper in the samples. This basis does not exactly represent the true condition, since the volume is constantly decreasing and a certain quantity of copper passes into the slag, but it is as near as can be obtained in practice. Take, for instance, in Table I., the sample No. 5, which shows : Cu, 59.9;

Jan 1, 1907

By H. W. Paxton, C. C. Busby

IT has been shown previously' that strain aging can markedly improve the tensile properties of low carbon martensites, especially the yield-tensile ratio, without seriously affecting the ductility. In view of interest in high strength steels, an investigation has been made of the effect of strain aging following tension or rolling on the tensile properties of A1S1 4340 in an attempt to obtain a tensile

Jan 1, 1957

By W. Barbarowicz, H. E. Uhland

AT the Noralyn mine and mill of International Minerals & Chemical Corp. in Bartow, Fla., process instrumentation has been incorporated in three departments-mining, flotation, and preparation. Use of the dragline is the most difficult aspect of the mining operation to control automatically. At the Noralyn mine there are two draglines, a Bucyrus-Erie 1250-B with 29-yd bucket and 235-ft boom and a Bucyrus-Erie 1150-B with 21-yd bucket and 215-ft boom. These are equipped with a minimum number of instruments, but further instrumentation would increase the operator's efficiency.

Jan 7, 1957

By R. L. Stone

None of the currently used methods of testing bentonites as binders for strengthening iron ore pellets is entirely adequate by itself. Since more knowledge was needed about 1) which properties of bentonite most affect pellet strength, and 2) the precise mechanism by which strengthening is produced, attention was paid to possible new techniques for rating bentonites. With the structural nature of bentonites — in particular, the montmorillonite component — the possibility of rating bentonites on the basis of zeta potential was investigated. These bentonites were also rated by conventional tests and measurements, including colloid content, barrel yield, pH, chemical analysis and physical tests on green and dry pellets. A mechanism for pellet bonding based on electro-kinetic forces between the bentonite and the iron ore concentrate appears to be feasible. In pelletizing, from 6 to 18 lbs of bentonite is added per ton of concentrate to give strength to the green and dry pellets. In some operations even more bentonite than is required for strengthening purposes must be added for moisture adsorption to pennit balling of the concentrate. Since bentonite is thus a major item in pelletizing, more knowledge about the way in which bentonites act as binders and better ways of rating this ability would help in the difficult job of selecting the right bentonite for a given concentrate. The fact of the matter is that although several methods are in current use for testing bentonites, none of these methods are consistently foolproof. For example, a given bentonite may rate high by several standard tests yet turn out to be a poor binder, and of course the reverse also occurs. Actually, more knowledge is needed about 1) which properties of bentonite most affect pellet strength, and 2) the precise mechanism by which strengthening is produced. In this study attention is therefore paid to possible new techniques for rating bentonites. With the structural nature of bentonites as a starting point, we investigated the possibility of rating bentonites on the basis of the zeta potential, i.e., the electrokinetic ootential on the montmorillonite colloids — the main component of bentonite binders. The zeta potential technique was applied to a range of commercial bentonites from several areas in the U.S. and abroad. These bentonites were also rated by conventional tests and measurements, including:

Jan 1, 1968

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth, W. L. Finlay

Titanium with up to 7.5 pct Al forms single-phase a alloys that are work hardening, not heat treatable, and ductile as welded. The high aluminum Y phase alloys are not usefully ductile, despite their low hardness, but they have excellent oxidation resistance and hot hardness. LITTLE has been published on the effect of aluminum on the mechanical properties of titanium, despite the fact that two of the first four commercial alloys released by titanium alloy producers contained aluminum as an important alloying ingredient. These were both a-ß type alloys, one containing 4 pct A1 and 4 pct Mn and the other containing 3 pct A1 and 5 pct Cr. However, neither of these alloys reflects the true alloying nature of aluminum, since each contains important amounts of the ß-stabilizing addition, manganese or chromium. In a previous publication on the constitution of Ti-A1 alloys,' the authors showed that aluminum had a high solubility in a titanium and was strongly a stabilizing in nature. About 25 wt pct A1 is soluble in a titanium at room temperature. With as little as 5 pct added aluminum, the a transus temperature is increased from 882" to 970°C, and the correspond- ing ß transus to 995°C. The first intermediate phase in the Ti-A1 system is the ordered face-centered tetragonal TiAl phase, which extends from 34 to 46 wt pct Al. The present paper presents hardness data over the entire titanium-rich region of the system, through the TiAl phase, and mechanical property data on the alloy range capable of being fabricated. Methods of Investigation The materials used and general preparation of alloys, as well as experimental techniques used in the investigation of Ti-A1 alloys, have been adequately described.' Briefly, the preparation consisted of arc-melting the desired amount of high purity aluminum (99.99 pct purity) and iodide titanium (maximum hardness 100 Vickers, as deposited) together on a water-cooled copper hearth under a partial pressure of argon. The resulting button ingot was of such form that it could be fabricated without further treatment. All work was done using ingots weighing 10 to 15 g, which were hot-rolled to strip form whenever possible. Tensile samples were 3.25 in. long, 0.5 in. wide, and 0.040 in. thick, with a reduced section 1.25 in. long by 0.250 in. wide. The gage length used was 1 in. Electrical strain gages mounted on the

Jan 1, 1954

By George H. Eldridge

The existence of phosphate of lime within the State of Florida has been known for over a decade; but until the spring of 1887, the extent and value of its deposit.;, possibly with one exception, were unsuspected. In that year Col. T. S. Moorehead, induced by a statement made by Mr. J. F. Le Baron, examined the gravels of the Peace river, recognized the importance of the deposits, acquired such tracts as were regarded as desirable, and established the pebble-phosphate industry, making his first shipment in May, 1888, to the Scott Manufacturing Company, of Atlanta, Ga. The establishment of the pebble-phosphate industry upon Peace river was followed, a year later, by the discovery in Marion county of an entirely different class of phosphate, now commonly known as hard-rock phosphate. This discovery was made early in June, 1889, by Mr. Albertus Voght, in a well which he was sinking upon his place near the site of the present town of Donnellon, about 20 miles southwest of Ocala. To it, more than to any other cause, is due the rapid and remarkable development of the present great industry of the State. It was, however, Mr. John F. Dunn, of Ocala, who turned to advantage the accidental discovery of Mr. Voght. After acquiring a knowledge as to the chemical composition and value of the material, Mr. Dunn and hid associates purchased several thousand acres of land and organized the Dunnellon Phosphate Company for active operations. From Dunnellon as a center, prospecting rapidly extended in all directions, until at the present day important mines have been opened over a well-defined tract more than 200 miles long and about 6 miles wide. This tract lies par-

Jan 1, 1893

By George R. Mansfield

Interest in the reserves of phosphate rock in the United States and their proper conservation has recently been aroused by hearings held in different parts of the country by the "Joint Committee to investigate the adequacy and use of phosphate resources of the United States." This committee was appointed within a few days after a Presidential message to Congress on the same subject, dated May 20, 1938, and began to function almost immediately. Hearings were held in Washington, D. C., Pocatello, Ida., Wilson Dam, Ala., Knoxville, Tenn., and Lakeland, Fla. The resulting testimony, when published, comprised a volume of 1182 pages.l At the earlier hearings held in Washington and Idaho the seeming disparity between the great reserves of the West and the smaller reserves in the East led to some suggestions as to the desirability of curtailing or even prohibiting the exportation of phosphate rock so that eastern producers, becoming alarmed, cooperated in making available for the use of the committee information hitherto closely guarded. This information has provided an opportunity for new studies by official agencies, for a restatement of the reserves of Florida and Tennessee, and for some modification of figures for the Western States. The writer, representing the Federal Geological Survey, was given free access to the Florida material and has prepared for publication a report,² some features of which are summarized in this paper. The Tennessee material was studied by Dr. G. I. Whitlatch,³ of the Tennessee Division of Geology. Prof. J. Stewart Williams,* of the Utah State Agricultural College at Logan, has published a recent study of the phosphate resources of Utah and the writer has given some further study to reserves of western phosphate from the viewpoint of including material of lower grade than that hitherto considered. Technologic advances in the phosphate industry must be credited with a large share in the expansion of reserves by making available for

Jan 1, 1942

By George R. Mansfield

Interest in the reserves of phosphate rock in the United States and their proper conservation has recently been aroused by hearings held in different parts of the country by the "Joint Committee to investigate the adequacy and use of phosphate resources of the United States." This committee was appointed within a few days after a Presidential message to Congress on the same subject, dated May 20, 1938, and began to function almost immediately. Hearings were held in Washington, D. C., Pocatello, Ida., Wilson Dam, Ala., Knoxville, Tenn., and Lakeland, Fla. The resulting testimony, when published, comprised a volume of 1182 pages.l At the earlier hearings held in Washington and Idaho the seeming disparity between the great reserves of the West and the smaller reserves in the East led to some suggestions as to the desirability of curtailing or even prohibiting the exportation of phosphate rock so that eastern producers, becoming alarmed, cooperated in making available for the use of the committee information hitherto closely guarded. This information has provided an opportunity for new studies by official agencies, for a restatement of the reserves of Florida and Tennessee, and for some modification of figures for the Western States. The writer, representing the Federal Geological Survey, was given free access to the Florida material and has prepared for publication a report,² some features of which are summarized in this paper. The Tennessee material was studied by Dr. G. I. Whitlatch,³ of the Tennessee Division of Geology. Prof. J. Stewart Williams,* of the Utah State Agricultural College at Logan, has published a recent study of the phosphate resources of Utah and the writer has given some further study to reserves of western phosphate from the viewpoint of including material of lower grade than that hitherto considered. Technologic advances in the phosphate industry must be credited with a large share in the expansion of reserves by making available for

Jan 1, 1942

By E. P. Mathewson

The experiments described in this paper were made at the Washoe Reduction Works, Anaconda, Mont., for the purpose of determining the relative speed of elimination of the iron, sulphur and arsenic during the process of bessemerizing copper-mattes. The samples were taken from a horizontal a barrel" converter, 8 ft. in diameter and 12 ft. 6 in. long, having an average charge of 9 tons of matte, and blown with a 16-lb. air-pressure. All samples were taken with the blast on, turning the converter from its normal blowing-position to nearly vertical, so that a conical mold, with a long handle attached to a horizontal rod, could be introduced from a platform above the converter into the mouth of the converter and a sample taken. The difficulties of taking a sample with the blast on are apparent, and the irregularities of' the lines in Figs. 1, 2 and 3 can be readily accounted for by the amount of slag in the samples. On the whole, the plotting of the results gives comparatively uniform lines, considering the conditions. The samples were taken by the regular sampling-force of the works at 10-min. intervals, as shown in Tables I., 11. and III., which also give the chemical analysis of the samples so taken. The test shown in Table I. was made with a new converter; that of Table 11. with a converter that had made three charges and had been cleaned out; that of Table 111. with a converter that had blown one charge to white metal, and had then been " washed " out and used for the test. In plotting these results, it was necessary to take, as a basis, the percentage of copper in the samples. This basis does not exactly represent the true condition, since the volume is constantly decreasing and a certain quantity of copper passes into the slag, but it is as near as can be obtained in practice. Take, for instance, in Table I., the sample No. 5, which shows: Cu, 59.9;

Jan 1, 1908

By M. E. Fine

IN the apparatus for measuring internal friction shown in fig. 1, a modification of that described by Kê,1,2 the parasitic energy loss or background is equivalent to a Q-1 of approximately 4x10-5. This low value of background was obtained by using a jeweler's collet of appropriate size for the upper support, eliminating lateral motion without immersing the bob in oil, and designing the bob to reduce air resistance. The pendulum is supported on the frame through a snug fitting, sliding rotary joint (fig. I-B). A slight twist of the top imparts essentially pure torsional motion to the pendulum. No evidence of energy loss in the sliding joint has been observed. In the bob (E) steel balls are used in the torsion arm, and the bottom is filled with lead giving a total weight of 94 g. A lighter bob may be used for small diameter specimens. Another bob was a solid disc with provision for adding discs to change the frequency. The oscillating image of the filament is recorded on a revolving drum camera (fig. 1-3) driven by a synchronous motor. This allows use of frequencies higher than can be measured visually on a glass scale. Samples varying in diameter from 0.020 to 0.075 in. have been measured, the frequencies have ranged from 1 to 12 cps, and the maximum strain varied from 0.5 to 10x10-5. With appropriate modification the sample may be placed in a thermostat. The apparatus may also be used to measure the shear modulus. In the examples of measurement given in table I the internal friction of Permendur and the 46.8 Ni-Fe alloy are due, for the most part, to magneto-mechanical hysteresis8 (elastic hysteresis accompanying stress-induced magnetostriction) which depends on strain amplitude and increases with annealing. The internal friction of most materials decreases with annealing. References IT. S. K6: Physics Review (1947) 71, 533. 2 T. S. Kê: Transactions AIME (1948) 176, 448; Metals Technology (June 1948) TP 23703. 3 R. Becker and W. Döring: Ferromagnetismus. 365 (1939). J. Springer.

Jan 1, 1951

By C. F. Cockrell, K. K. Humphreys, H. E. Shajer

It is quite conceivable that the question of using coal or an alternate fuel in the future by large industrial consumers may be decided on the basis of possible profitable utilization of flyash. Accordingly, the Coal Research Bureau at West Virginia University has been attempting to develop new uses for this waste material. This effort has resulted in the development of a process for producing flyash-based face brick and other structural materials which generally exceed published specifications for competitive clay-based materials. These structural materials, containing up to 97% waste coal ash, can be produced from flyash derived from most coals without regard to the physical or chemical properties of the coal ash. Preliminary production cost estimates indicate that face brick can be manufactured at a rate of 9000 brick per hr or more with a resultant gross profit of over $24.00 per thousand brick. Plant payout time for a plant of this size would be only about 1.2 years assuming a market price of approximately $55.00 per thousand, a well established figure for comparable clay brick. With flyash production expected to more than double in the next 15 years, there is an increasing need for a practical and Profitable method for the utilization of large tonnages of this material (see Table I listing total flyash production of utilities in each state of the U.S.). Present industrial and governmental physical and chemical restrictions, particularly for use as a lightweight filler or pozzolanic material, have limited the use of flyash considerably. For those ashes which have met the required standards, utilization is not always assured because of lack of promotion and poor public acceptance. Less than 6% of the total flyash production in the U.S. was sold in 1962. The remainder was dumped in disposal areas at costs as high as $2.42 per ton.' It is quite conceivable that in the near future the question of using coal or an alternate fuel by large industrial consumers may be decided on the basis of the possible utilization of flyash. To help insure future coal demands, the Coal Research Bureau at

Jan 1, 1968

By Philip D. Anderson, Ralph Hultgren

Heat contents of extremely pure iron were measured over the range 300"to 1433"K, using a diphenyl ether calorimeter. Results from three samples containing widely differing impurities agreed with one another and with Previously reported results at higher temperatures (1184 ° to 1809°K) by Olette and Ferrier. From these data a table of heat contents of iron has been Prepared which is believed to be more accurate than those previously available. CP values have been derived which are consistent with these heat contents, with the best experimental Cp data, and with the thermodynamic conditions of equilibrium between bcc and fcc iron. The opinion is expressed that low-temperature extrapolations of presently known Cp values for y-Fe are not reliable. It would seem that the thermodynamic properties of iron, which is by far our most important metal, should have been well established long ago. This is not the case, however. As discussed by Olette and Ferrier,' there is objection to every earlier heat content measurement. While the best true Cp determinations agree well at temperatures below the Curie point, there is wide divergence at higher temperatures. Several investigators have examined available data and attempted to calculate thermodynamic functions for iron that are consistent with the two equilibrium temperatures of bcc and fcc iron. The two primary efforts were those of Austin' in 1930 and Darken and smith3 in 1948. The recommended values differ considerably; integration of Austin's Cp values leads to a heat content at 1100°K which is 300 cal per g-atom higher than the value recommended by Darken and Smith. The compilation of Fisher4 in 1949 was based on the selection of Austin. In 1956, Weiss and Tauer obtained yet another set of values by resolving Cp values into components due to dilation, lattice vibration, electronic excitation, and magnetism. The magnitude of contribution by each component and its dependence on temperature was estimated by semiempirical means. Their values are not self-consistent in that they do not form smooth curves when plotted vs temperature; moreover, their calculations cannot easily be repeated since they do not give the values of some of the parameters used. Clearly, experimental values for iron were in a most unsatisfactory state. The presently described measurements of the heat content of iron were therefore undertaken, covering temperatures as high as 1433°K. While the work was in progress, the high-temperature (1193" to 1789"K) heat content measurements of Olette and Ferrier' were published; in the region of temperature overlap the present results agree with Olette and Ferrier well within experimental accuracy. It is believed that the present results, combined with those of Olette and Ferrier, provide for the first time a reliable set of heat contents of iron from room temperature to the melting point. From these data, guided by available Cp measurements, it proved possible to derive Cp, entropy, and free energy function values for @-iron from room temperature to the melting point, and for y- iron in the temperature region of its stability. Exhaustive study led to the conclusion that extrapolations of y-iron functions to room temperature were not reliable enough to be useful; hence these have been omitted from the tables. EXPERIMENTAL Materials. Three samples of extremely high purity iron from different sources, containing widely different impurities, were measured. The first of these, designated "Chipman", was kindly supplied by Dr. K. K. Kelley of the U. S. Bureau of Mines from a lot which was made many years ago by Dr. John Chipman of the Massachusetts Institute of Technology. The second, designated6'Teddington", was supplied by the National Physical Laboratory, Teddington, England, from a lot zone-refined by them. The third sample, designated "Irsid", was supplied by the Institute de Recherches de la

Jan 1, 1962

By Takeyasu Ito, Mayumi Someno, Kazuhiro Goto

SINCE the pioneering work by Kiukkola and Wagner,1 many experiments have been reported on solid electrochemistry at elevated temperatures. However, the studies have been confined to experiments under isothermal conditions. One may conceive many situations under nonisothermal conditions. With two different temperatures T1, and T2 at the two electrodes, the electromotive force, E of a Galvanic cell will be expressed by the following equation under a steady state heat transfer in solid electrolytes of zirconia-lime and thoria-lime. E = ^ $ l&-dGO2+a(T2-Ti) [1] where tO2- is the transference number of oxygen ions in the electrolyte, Go, is the chemical potential of oxygen, and a is the coefficient of the thermoelec-tromotive force due to the temperature difference. The objective of the present study was to evaluate the coefficient of the thermoelectromotive force for zirconia-lime and thoria-lime under isobaric condition. The physical meaning of this coefficient is out of the scope of the present communication. The experimental cell assembly is schematically shown in Fig. 1. The zirconia-lime electrolyte tube and thoria-lime electrolyte tube were 8.0 mm OD and 5.0 ID, from commercial sources with chemical analyses of 94.8 wt pct ZrO2, 3.85 pct CaO, 0.83 pct SiO2, 0.25 pct TiO2, and 0.05 pct Fe2O3; and 95.0 pct ThO2, 4.0 pct CaO and rare earth metal oxides, respectively. The specific gravity was 5.5 g per cu cm for zirconia-lime and 9.8 g per cu cm for thoria-lime. Original powder size before shaping and sintering the tube was several microns for both electrolytes. The distance separating the two electrodes was 4.0 or 5.0 cm. Platinum wire of 0.5 mm diam was used for the electrodes. The temperature gradient was controlled by heating one electrode with a small heating coil of nichrome wire. The temperatures at the two electrodes were measured with two calibrated Pt-13 pct Rh:Pt thermocouples, directly contacting the two platinum electrodes. The atmosphere was either air or pure oxygen. The partial pressure of oxygen in air was considered equal at the vicinities of the two electrodes, with negligibly small thermal segregation in the gas phase. The difference of the chemical potential of oxygen was controlled only by the temperature difference at the two electrodes and not by the oxygen pressure difference. The temperature ranges were 600" to 1200°C for zirconia-lime and 850" to 1200°C for thoria-lime electrolytes. Fig. 2 shows the relation of the measured electromotive force and the difference of the oxygen chemical potential at the two electrodes for zirconia-lime and thoria-lime electrolytes. The electromotive forces in the figure were measured by a *0.05 mv potentiometer. The chemical potential difference was calculated by the following equations.'

Jan 1, 1970

By Alberto J. Terrones L.

THE classical papers on contact metasomatic deposits by Lindgren on the Clifton-Morenci district,1 by Barrel1 on Marysville, Mont.,2 and by Goldschmitt on the Oslo district, Norway,3 laid the foundation for understanding of the importance of separating the metamorphic process from the subsequent metasomatic stage. Knopf4 made a big step forward by recognizing that sulfide ore minerals are invariably younger than silicates and by further stressing the importance of structural control5 ore finding. Some years later Harrison Schmitt6 fought the idea that contact metasomatic deposits are erratic, irregular, bunchy, economically marginal, and of small size, concluding that these descriptions have little factual basis. He emphasized the importance of detail mapping and careful geological study as fundamental requirements for a better understanding of these deposits. This article presents a comparative description of the structural features at the Magistral, Antamina, Morococha, Vilca, Ferrobamba, Katanga (Quibio), Tintaya, and Huarca contact deposits (Fig. 1). Further, it will describe how these structural features controlled the emplacement of the intrusives, their shape, distribution of metamorphic and metasomatic halos, and sulfide deposition in post-skarn structural channelways. Finally, the modifications introduced by a superimposed hydrothermal stage recognized at some localities will be discussed.

Jan 3, 1958

By J. Spotts McDowell

Preparation and Use.-Magnesite is an important refractory in open-hearth, heating, and electric furnaces for steel-making and in many of those employed in the metallurgy of copper and lead. It is sold in the form of brick, finely ground "furnace magnesite" for brick-laying, and dead-burned grains for making and repairing furnace bottoms. The latter are a mixture of granules varying in size from pieces of about 5/8 in. (1.6 cm.) diameter to very fine but sandy particles. Dead-burned magnesite results from calcining 'the crude or lightly burned mineral at a temperature that will not merely drive off practically all the CO2, but will also cause sintering of the particles. During this process the pieces shrink considerably and become hard, dense, and inert to atmospheric moisture and C02; under-burned material, on the other hand, will hydrate on exposure to the air. A small percentage of ferric oxide seems to be necessary for the production of a satisfactory sinter; from 4.5 to 8 per cent. in the dead-burned grains is considered the most desirable amount. Dolomite has been little used for brick-making in the United States, but it is prepared for use in the granular condition calcined or "double-burned" and is the principal ingredient of several materials offered for sale under various trade names for refractory purposes. Dolomitic refractories are almost wholly confined to the open-hearth and electric furnaces, where they are used for fettling and as substitutes for magnesite. Much more magnesite and dolomite are used for basic open-hearth steel-making than for all other refractory purposes. The hearth of the furnace is usually built up of magnesite brick and dead-burned grain magnesite so laid that the brick base is protected by a working bottom of the granular material. The latter is sintered into place in layers 1 to 2 in. (2.5 to 5 cm.) thick to a total depth of 12 to 18 in. (30 to 45 cm.) at the center of the furnace. After each heat, burned dolomite is thrown against the banks as high as it will stick, and all holes in the bottom are filled. At most plants such holes, at the end of each week, are also

Jan 2, 1919

By Mungo Park, C. Baring Horwood

This paper is intended, in the light of recent investigations, to call attention to some of the essential features of good practice in sampling and mine-valuation. Mine-sampling may be divided broadly into two classes: (1) development-sampling and cornputatioll of ore-reserves; and, (2) stope-sampling and estimation of stope-values. Development-Sampling. It is with development-sampling only that this paper deals— the term development being taken to mean the opening-up of a mine by cross-cuts, drives, connections, etc., preparatory to actual extraction of the ore for milling. In development-sampling the work of the sampler and the consequent estima-

Jan 1, 1909

Jan 1, 1952