Search Documents

By M. J. GAVEN

COMING over from the plant on the Denver and Rio Grande yesterday afternoon I was an interested listener to a smoking-room conversation that had to do with the experimental plant near Rifle. The people who were talking didn't know me and I didn't know them, but I learned quite a little. I understood that the plant would never operate; that it was not intended to operate; that the "oil trust" would keep it from operating; that our tramway had eaten up all our money and still was not working and would not work; that the plant was run by a bunch of kids, and that the superintendent was probably the biggest kid of the bunch. I plead guilty to the latter. But the people who were talking were misinformed. The plant is producing oil. The first sample of oil that came from our unit at the Bureau of Mines experimental plant at Rifle, Colo., was produced on Sept. 18, the first that came out of the condenser, and it is still coming. This sample of oil may mean to the United States what the first oil produced from the first well meant.

Jan 1, 1926

By N. A. Gokeen, M. Ohtani

EFFECT of elements on the solubility of carbon in liquid iron is useful in calculating and correlating a number of thermodynamic properties as shown elsewhere in detail.' Kitchener, Bockris, and spratt2, and later Turkdogan and Hancock3 have investigated the effect of sulfur on the solubility of carbon at various temperatures and concentrations. For any chosen sulfur concentration, the solubility of carbon reported by Kitchener et al. is considerably lower than that by Turkdogan and Hancock. It was therefore felt that a reinvestigation of this problem was necessary. EXPERIMENTAL METHOD An alloy of Fe-C-S .was prepared with electrolytic iron and ferrous sulfide melted by induction in a graphite crucible, 4 in. high 1 1/2 in. ID under a CO-atmosphere. The temperature, held at 1500" ± 5°C in all experiments, was measured with a Pt-Pt + 10 pct Rh thermocouple immersed into the melt. In order to assure saturation with carbon, the melt was stirred with a graphite rod. After approximately 1 hr at 1500 °C, a sample was obtained by sucking the melt into a silica tube, 4 mm ID. The sample was then analyzed for carbon and sulfur by usual methods. RESULTS The results are presented in Table I and plotted in Fig. 1 with the individual values of Turkdogan and Hancock.3 Scattering in the data is equivalent to 3 pct or less in carbon analysis. The broken line represents the empirical equation obtained by Kitchener et al. from their data. It is evident that the present data are in good agreement with those of the former investigators but in disagreement with the latter. The cause for this discrepancy cannot be readily offered since the experimental methods in the three investigations were nearly identical. Additional evidence corroborating the author's results may be presented in the following manner. The difference between the solubilities of carbon in the ternary Fe-C-X melt with a small concentration of any element X, and in the binary Fe-C melt is %?C = %CIII-%CII [1] where %?C is the change in solubility, and %CIII and %CII are the solubilities in the ternary and the binary systems respectively. The value of %Cii

Jan 1, 1961

By Robert D. Pehlke, Weldon L. Daines

The reduction of manganese oxide from a basic slag by silicon dissolved in liquid iron at steelmaking temperatures was studied to determine the rate-controlling step for the process. The experiments were carried out under an argon atmosphere in a resistance-heated vertical-tube furnace. The two liquid phases, slag and metal, were held in zirconia crucibles. Sampling and chemical analysis of the slag phase led to time-concentration curves for the system. Results obtained by varying parameters such as temperature, stirring rate, concentration, and melt geometry defined the limiting reaction mechanism. The reduction of manganese oxide by silicon is a fast reaction and reached equilibrium within 90 min. The rate of stirring has a marked effect on the reaction rate, while, on the other hand, the effect of temperature is very small. This identifies the rate-controlling step as diffusion rather than interfaciul chemical reaction. The variation of other parameters revealed that a) diffusion of manganese in the iron phase is the slow step, b) the value of D/6 for manganese in iron at 1550°C is 7x 10-4 cm per sec, c) the energy of activation for the apparent rate constant is 7 kcal per mole, and d) increasing the amount of silicon in the iron decreases the diffusion coefficient of manganese. THE equilibrium relations pertinent to the reduction of manganese oxide from a steelmaking slag by silicon dissolved in liquid iron have been studied, but little is known about the mechanisms that control the rate of the process. The purpose of the present investigation was to study the rate of reduction by silicon and to determine the rate-limiting step. The effects of stirring rate, temperature, composition, and melt geometry were investigated as a means of identifying the controlling step. On the laboratory scale, relatively little work has been done in the area of slag-metal kinetics, primarily because of the problems confronted in attempting to contain liquid slags and metals in laboratory crucibles at steelmaking temperatures. Since graphite is an ideal material for a crucible, several investigations have been carried out on the reduction of various oxides from a slag by carbon in graphite-saturated iron and on the transfer of sulfur between a slag and graphite-saturated iron. Most of this work has been performed in induction furnaces. Studies where the container was not graphite are extremely limited. A single kinetic study of manganese transfer between molten iron and basic slags was carried out by Sano, Shiomi, and Matsushita.' These investigators prepared calcium oxide and titanium oxide crucibles to contain the two-phase system. Only a few experiments were carried out and the results had to be treated qualitatively. Despite the paucity of kinetic data, a large quantity of information is available in the literature concerning the thermodynamics2-12 and physical properties'3-21 of the slags containing manganese oxide and the dilute liquid iron alloys containing manganese and silicon which were involved in this research program. EXPERIMENTAL METHOD A vertical-tube resistance-heated furnace was used in this investigation to study the slag-metal reaction Although most previous slag-metal studies were carried out in induction furnaces, a resistance furnace has several advantages including better control of temperature and stirring rate. Hence, a resistance furnace was selected for this study, and its design is shown schematically in Fig. 1. Slip-cast, fine-grained, low-porosity, lime-stabilized cubic zirconia crucibles were used for the kinetic experiments. The crucibles were 4 1/2 in. high and 2 1/8 in. OD with a 1/16-in. wall. The crucibles were only slightly

Jan 1, 1969

By D. Harrington

One of the main functions of the United States Bureau of Mines is to obtain and disseminate information that will promote safety in and around mines, and the health and safety of employees engaged in mining. Serious health and safety conditions arising out of contamination of air in metal mines by dust, fumes from explosives and fires, and absorption of oxygen by timber and other causes, led the Bureau of Mines to cooperate with the United States Public Health Service in the study of dust occurrence and ventilation in metal mines in various parts of the country. A. J. Lanza, of the U. S. Public Health Service, and Edwin Higgins, mining engineer of the U. S. Bureau of Mines, in 1915, made a detailed study in the mines around Joplin, Mo.; their reports1 are now available. In 1916, 1917, and 1918, a similar study was made in the Butte, Mont., region by Doctor Lanza and D. Harrington, mining engineer of the Bureau of Mines; the reports of this investigation will be available soon. In 1919, the study was continued in some of the Arizona mines by D. Harrington, of the Bureau of Mines, and G. E. McElroy and R. A. Koronski, of the U. S. Public Health Service, the underground work being completed in June, 1920; these reports are now being prepared for publication. In the spring of 1920, the scope of the work was extended, with D. Harrington in charge as supervising mining engineer, and short studies were made in the mines of the Coeur d' Alenes in Idaho and around Oatman, Ariz. It is hoped soon to extend the work into mines of California, Nevada, Colorado, Michigan, and Minnesota, and ultimately to other states should the mining companies be willing to coöperate. While the coöperation of the mining companies is necessary, the companies are put to practically no expense other than supplying a guide to accompany the investigators underground, the length of time spent

Jan 1, 1922

[ ]

Jan 1, 1938

By Paul Tyler

STRATEGICALLY situated in almost the heart of the leading fertilizer-consuming area of the United States, Tennessee long has ranked second only to Florida as a phosphate-producing state. Since 1932 its share of the national output of phosphate rock has increased steadily, and in 1937 its production mounted to an all-time record. More significant even than the increase in tonnage are the forward strides in technology. The Tennessee Valley Authority's research program has led to quasicommer-cial operations using hydroelectric power to manufacture concentrated phosphatic fertilizer that is used to further the farmer education program designed to streamline the fertilizer business and halt the appalling waste of farm land by soil erosion. Even more stimulating to chemically minded imaginations is the production of elemental phosphorus by a private company that not only has succeeded in extracting it from the phosphate rock in electric furnaces but actually has contrived to capture it and to transport it safely in tank cars. New values have been created for low-grade phosphate deposits, and the economic life of reserves has been lengthened while the waste of former years goes back into the mills for recovery of its values by modernized methods. Tennesse's phosphate-mining industry dates from the discovery of blue rock in Lewis County in December 1893. Its known reserves are of the order of 101,500,000 tons, which compares with the production of 825,099 tons in 1937; that is, 21 per cent of the phosphate-rock output of the whole nation. The total output reported from 1894 until July 1, 1938, was approximately 19,000,000 tons. Official estimates of reserves are overly conservative and evidence submitted before a joint Con-gressional committee in November 1938 places "probable" reserves at more than 6,000,000,000 tons.

Jan 1, 1939

By William Greenawalt

The Greenawalt electrolytic copper extraction process is applicable to suitable oxide ores, sulfide ores and concentrates, and low-grade matte. The process is self-sustaining in acid on sulfide ores or concentrates, on mixed ores, on high-grade oxidized ores; and on low-grade oxidized ores the amount of acid to be purchased or manufactured is greatly reduced. The ferric iron is under easy control, and copper may be effectively deposited from solutions of any acid or iron content likely to be used in copper leaching. From 60 to 75 per cent. of the copper may be removed from the solution in passing through the electrolytic department, before returning the solution to the ore. The amount of copper requiring chemical precipitation, from the waste and foul solutions, is only about 5.0 per cent, of the total copper produced, and this 5.0 per cent. is converted into the electrolytic metal in the regular operation of the process. The entire process can be made practically automatic, and can be carried out mechanically. There is no uncertain departure of any kind in the application of the process; no unusual or unproved apparatus is used. EVER since electrolytic copper refining gave promise of success, about a half century ago, efforts have been made to apply the idea to the extraction of copper from its ores. The methods of attack have, usually, been to leach with a dilute acid and then to deposit electrolytically the copper from the resulting solution with the simultaneous regeneration of the solvent used in the process. Many efforts have been made, and many patents have been taken out, both in the United States and abroad, to give this idea practical application, but only within the past few years have the difficulties been surmounted. Leaching and electrolysis, as applied to copper ores, are among the most promising fields in modern metallurgy. New conditions are arising, which will bring the wet methods into prominence; while high freight rates and increasing cost of fuel will tend to limit smelting to highly favored localities. The possibilities offered by the installation of hydro-electric plants and the greatly enlarged range of power transmission will greatly widen the field of electrolytic methods.

Jan 1, 1924

Jan 1, 1969

Jan 1, 1969

By F. W. Bowdish

A theoretical and experimental laboratory study has shown that the rate of breaking of oversized particles in a ball mill is proportional to 1) the concentration of such particles, and 2) the area of the balls, provided that the balls are larger than a certain size relative to the particles. If all undersized material were removed as formed, the rate of breaking would be almost independent of the quantity in the mill. Rate equations are given which are similar to those for zero, first, and second order reactions. Deviations of small balls from the equation for a second order phenomena are quantified by a factor called "nipping efficiency." Some data are correlated by a dimension-less equation, which is used to estimate nipping efficiencies from data not in the correlation. The investigation described here was undertaken after a literature survey revealed that little was known concerning the mechanism of breaking of particles within a ball mill and the effect of this mechanism upon grinding rates. One paper, by Roberts1 , offered a theory concerning the mechanism of breaking, and a rate equation for the breaking of particles larger than some size to particles smaller than that size. That paper provided the starting point for a theoretical and experimental investigation of grinding under carefully controlled conditions. THEORETICAL CONSIDERATIONS In his paper on the probability theory of ball mill grinding, Roberts theorized that "... a given expenditure of power leads either to a certain number of point to point blows per bp-hr or to a certain distance of line contact per hp-hr ..." He assumed that the balls touch each other during each blow or during moving contact. Then he said that a volume of pulp, dependent upon the size being considered, would be covered per minute within which all oversized particles would be crushed to particles smaller than that size. Naturally, the higher the concentration of oversized particles in the pulp, the higher the rate of which they would be broken. From this reasoning Roberts obtained the differential equation -dC/dt = k hp/ton C (1) where k is a constant for any size of particle, density of particle, and moisture content of pulp. C is the percentage of oversize in the material to be ground, t is the time, and hp/ton is the power input per ton of material in the mill. He then integrated the equation to log Co/Ct = k/2.3 hp/ton t , where Co and Ct are the percentage of oversize at time zero and t respectively. By always using the same quantity of material in a mill and assuming that it required constant power to run the mill, he was able to combine the horsepower per ton factor with the other constants to give an equation for a first order rate.

Jan 1, 1961

By G. T. Engel, W. G. Gruzensky

Jan 1, 1960

By George Comstock

IT seems a common opinion among metallographists that all light-gray inclusions seen with the microscope in polished sections of steel are manganese sulphide. Examples of this belief are continually appearing, as for instance in the paper by Dr. Henry Fay on manganese sulphide as a source of danger in steel rails,1 and in Lieutenant-Commander Cook's paper on Metallography of Steel for U S. Naval Ordnance.2 Slate FIG. 1-TRANSVERSE VIEW OF THE EDGE OF A SMALL HOT-ROLLED STEEL ROD. ETCHED WITH PICRIC ACID. X 200. colored inclusions are considered to be silicates, and dove-gray inclusions, manganese sulphide. To show the danger in the latter unqualified assumption, it should be sufficient to examine the edge of any piece of steel that is covered with a fairly thick scale, and that has been polished in such a way as to prevent the scale from breaking away entirely below the polished surface. This can be done by protecting the scaled edge of

Jan 12, 1916

By Wilhelm Borchers

IN all special branches of the chemical and metallurgical industries, in which large electric furnaces became necessary for carrying out new processes or for the improvement of old ones, the development of the electric furnaces took place on much the same lines. The endeavors to make a success of a new idea brought forth many ingenious designs, which, however, almost without exception, furnished the proof that the safest and shortest way to practical success is the utmost simplicity of construction of the necessary apparatus. Our knowledge of the qualities of materials for building electric furnaces and of the constituents of the furnace-charges, especially their electric conductivity and their chemical affinity . towards one another at high temperatures, is still far from being complete, and from this fact we must conclude that the smaller the number of elements in the construction of a furnace, the fewer the number of unreliable factors both in the construction and in the operation of the electric furnace. This conclusion deserves special attention when an electric furnace for making steel has to be chosen from the constantly growing number of inventions, inasmuch as the chief con¬stituent of steel, the element iron, is a substance which in its liquid phase has so great an affinity fir those elements which are to be removed from the charge, that it is very difficult to comply with the following conditions: 1, to beat the refining-slag to the highest point of its chemical activity ; to prevent the iron from entering the slaw, or, where this cannot be done, to make it enter so that it finally appears in the end-product

Jan 1, 1910

By G. B. Pryde

IN laying out a new mine, provision should be made for the ultimate recovery of as much coal in any given bed as is consistent with safety and economic mining. Though each mining district, if not each individual mine, has problems that make the adoption of any hard and fast rule impossible, certain basic principles are adapted to practically all conditions. One of the most vital is the provision for barrier pillars of ample dimensions to protect all haulage and permanent airways during the life of the property. Where conditions permit, room or butt entries should be driven on the strike or slightly to the raise and rooms turned at right angles to said entries. The width of rooms and room pillars is governed by conditions prevailing in the mines under consideration. A safe rule is: In advancing, extract not more than 25 to 35 per cent. of the entire seam; in exceptionally thick seams, considerably less than 25 per cent. should be taken. Rooms usually vary in length from 250 to 350 ft. (76 to 106 m.) with a barrier pillar of not less than 80 ft. between the last crosscut in rooms, and entry and room crosscuts should be driven on sights; room crosscuts should be driven at right angles to the direction of the rooms. In mines under excessively heavy cover or where roof conditions are bad, rooms should be driven narrow and a barrier pillar left at every fifth to tenth room. This barrier should be of such dimensions that one or more rooms, with pillars of usual dimensions, may be turned through it when the barrier is no longer required. Two of the advantages of such a barrier are the protection of the panel against peaking of roof load during pillar extraction and the easy closing of the entry in case of fire.

Jan 2, 1921

By J. Geertsma, F. de Klerk

During the hydraulic fracturing treatment of an oil or gas well the liquid pressure in the borehole is increased until tensile stress in the surrounding rock exceeds tensile strength. Once a tensile fracture is initiated, it is penetrated by liquid from the borehole and fracture propagation under continuous hydraulic action takes place. The fracturing liquid carries a propping agent to ensure a highly permeable flow channel after pressure release. Field results range from failure to obtain increased production to outstanding success. In all cases, however, it unfortunately remains uncertain whether the values chosen for the operational parameters, such as injection rate, pumping time and fluid viscosity, were in fact the ideal ones. Though experience provides a lead, a more satisfactory way to predict results would seem to be to subject the fracture propagation process to a theoretical analysis that (1) makes the maximum use of the relevant physical information and (2) so simplifies the resulting calculations that the field engineer gets practical data that he can handle comfortably. We are attempting here to do this in connection with the prediction of fracture width and areal extent before pressure release. What remains of the fracture afterwards depends on the distribution of the propping agent between the fracture walls, and that is a separate story. Idealization of the Problem To keep the problem tractable, a number of simplify- ing assumptions have had to be made: 1. The formation is homogeneous and isotropic as regards those of its properties that influence the fracture-propagation process. 2. The deformations of the formation during fracture propagation can be derived from linear elastic stress-strain relations. 3. The fracturing fluid behaves like a purely viscous liquid; i.e., any peculiar flow behavior due to the addition of gelling agents or other additives is neglected. Moreover, the effect of the propping agent distribution on the distribution of fluid viscosity in the fracture is not taken into account. 4. Fluid flow in the fracture is everywhere laminar. 5. Simple geometric fracture-extension patterns are assumed — either radially symmetrical propagation from a point source (Fig. 1A) or rectilinear propagation originating from a line source (Fig. 1B). In the first case the periphery of the fracture is circular, in the second case it is rectangular. 6. A rectilinear propagation mode can be accomplished only by injection over a large perforated interval, thus forming a line source. Such a rectilinear fracture must therefore be located in the vertical plane. A circular propagation mode might be expected from injection through a narrow band of perforations. This forms a point source. Because gravity effects are excluded from our considerations, the fracture propagation plane may in this case assume any angle with respect to the wellbore as far as the

Jan 1, 1970

By F. F. Skiba, P. J. Root

A mathematical model has been used to investigate crossflow effects in a stratified reservoir during an idealized displacement process. A process in which one incompressible fluid displaces completely another incompressible fluid of the same density and viscosity was considered. The reservoir was assumed to be composed of homogeneous layers which are discrete but interconnected. Approximate five-spot flow geometry was simulated by arranging two pie-shaped cylindrical (two-dimensional) wedges in series. Some of the common production methods rely, for their effectiveness, on the fact that the formation consists of isolated strata. This is particularly true of selective plugging and single-zone production-injection methods. The effectiveness of these techniques for several cases in which adjacent strata are in communication has been evaluated. The usual production-injection schemes for fluid injection processes involve using the same completion interval in both the production and the injection wells. The efficiency of this, as well as alternative productioz-injection procedures has been examined for some cases involving communicating strata. INTRODUCTION The performance of many fluid injection projects is marred by early breakthrough and by production of a high percentage of the displacing phase after breakthrough. This channeling effect, if it occurs in reservoirs which have large permeability variations, is often explained on the basis of a model composed of discrete, isolated strata. Corrective or preventive measures based on this same model are also common. The behavior of stratified models has been the subject of considerable study. An excellent review of the early literature was given by Seba.1 Studies of the depletion performance have since been made for continuous, unrestricted communication between strata2-4 and for production from one permeable bed in continuous but restricted communication with an adjacent permeable bed.5,6 Model studies of displacement processes in stratified systems with crossflow also have been reprted.7-12 Finally, methods which account for crossflow have been developed for computing displacement behavior in stratified systems.13,14 Most methods for controlling or preventing channeling involve some change in the interval open to production and/or injection. Although many variations of the selective completion problem have been studied in regard to the depletion of a reservoir, little attention has been given to the behavior of a displacement process under similar conditions. Sebal used a resistance network model to study the performance of a process in which one incompressible fluid displaces an identical fluid from a linear, stratified reservoir. He investigated the possibility of improving the vertical coverage by limiting the completion interval of the production well. This investigation deals with techniques in which selective completion of the production and/or the injection wells is used in an attempt to control channeling. At one extreme, selective plugging and single-zone isolation (assuming perfect execution) should be successful if the reservoir is actually made up of independent strata. At the other extreme, they can hardly be expected to be successful if the channeling is caused by a mechanism in which stratification effects are negligible even though there are extreme variations in the formation permeability and/or the injectivity profile of the wells is not uniform. By contrast, it is difficult to anticipate the effect that the amount of communication between the beds of a stratified system will have on the efficiency of selective completion techniques. The objective of this study is the quantitative determination of the effect of communication on the behavior of some particular stratified systems which will at least lead to qualitative conclusions.

Jan 1, 1966

By Edna A. Dancy, Gerhard J. Derge

Jan 1, 1963

By T. S. Blair

I feel a certain sense of responsibility in bringing before you the subject of the direct process in iron manufacture. I am aware that, in such a body as I have now the honor of addressing, there are few who are not already so well informed upon its past history that it would be a weariness to them to listen to anything else than an account of practical success. Yet, to claim that success involves so much that, if I do not make good my claim, I deservedly expose myself to severe criticism. The whole literature of the art, so far as it relates to the direct process, is, up to this time, but a history of failure. It is safe to say that more money, time, and talent have been fruitlessly spent in the pursuit of this object than in all the other unsuccessful efforts in the whole line of iron metallurgy. A distinguished authority in patent law has remarked that " the invention records of the United States and of foreign countries are filled with the waifs and abandoned relics of these abortive struggles." Dr. Percy, whose great work may be taken as an epitome of all that was worth mention, whether useful or curious, in pig-iron metallurgy, up to the date of its publication (1864), after giving elaborate accounts of various attempts at the direct process, condenses his own opinion of all that had been then effected, into a brief but summary comment upon a pamphlet of one of the sanguine inventors who had said: "It is evident that the present mode of working iron

By E. W. Pehrson, J. W. Furness

NONMETALLIC MINERALS, exclusive of fuels, may be divided into three groups: Building materials, fertilizer minerals, and miscellaneous minerals. Building materials, such as sand, gravel, slone, lime, and the ingredients of cement and clay products, occur widely in nature and are thus available near consuming centers at relatively low prices. Cost of transportation over great distances deters any' substantial movement in world trade. On the other hand, fertilizer minerals, such as phosphate rock, potash, nitrates, sulfur, and pyrite, and the miscellaneous nonmetallic minerals, such as long-fiber asbestos, mica, graphite, fluorspar, and china clay, do not have such widespread occurrence and consequently contribute the major part of the world's commerce in such minerals. The U. S. Bureau of Mines has prepared charts showing the inter-

Jan 1, 1936