Search Documents

By John Griffen

OF the western European countries, only England has made any extensive use of equipment developed initially by the coal preparation industry of the United States. About 20 years ago, the Chance sand flotation process for cleaning coal was introduced in England, and it has had a fairly wide adoption, particularly in the South Wales coal fields. In recent years, particularly since 1946, a considerable number of Denver flotation cells have been installed throughout the English coal fields for the cleaning of slurry. Until the advent of the Denver cells, the flotation of coal slurries in Western Europe had been done largely with the Mineral Separations cell or its modifications. Kleinbentik of Dutch State Mines had developed a cylindrical cell used in Holland and occasionally in Belgium and France. In England, the establishment of the National Coal Board to control the planning and operation of all coal production has retarded somewhat modernization of properties. A considerable period of study was required before definite long-range plans could be formulated. It was soon recognized that stopgap measures were needed in many cases to bridge the period until final plans could be developed and consummated. One of the stopgap problems in coal preparation was providing plants of small and medium capacity that could be used for a few years at one site and yet could be moved economically to another site so as to reduce depreciation charges per year and per ton. Such plants are being installed but the most satisfactory answer probably has not yet been found. One such installation uses a Norton Baum jig to wash 6 in. to 0. The equipment is in a steel structure rather than in a reinforced concrete frame with brick curtain walls, which is the normal structure for permanent plants. Since England has between 700 and 800 preparation plants for an output of 200 million tons per year, one of the long-range objectives is a consolidation of mine output which will require fewer coal

Jan 1, 1952

By Rudolf Gahl

Some time ago the Detroit Copper Mining Co. had to decide the question whether it would pay to re-treat slime-tailings, and several machines were tested in order to ascertain the type of construction which would give the greatest saving. In previous tests on the ore of this company, several tables proved far inferior to the Frue vanner, and for this reason they did not receive any serious consideration. In the late tests, however, one table was found to surpass the vanner in the percentage of saving made. The Frue vanner used in these tests had been adjusted approximately to the slope which the slime-vanners in the concentrator of the Detroit Copper Co. had at that time, about 2 in. between the inside of the wooden posts, or 0.272 in. per ft. It had not been determined, however, if this slope was the most economical one for treating the slime-feed in the mill, or for re-treating the tailings from the slime-vanners, and I was instructed to ascertain by test-runs, under different conditions, the best adjustments for the work to be done. In order to determine if a change in the adjustments of the machines would improve the results, it seemed sufficient to continue running the tests between the vanner and the table before mentioned, keeping the feed and all other conditions the same, but varying the adjustments of the vanner from run to run. I employed a vanner-man of long experience to operate these machines, who expressed the opinion that a slope between 28 and 2.5 in. between the posts (0.323 and 0.340 in. per ft.) would give the best results. Some runs made this way gave a considerable improvement. While for a slope of 2 in. (0.272 in. per ft.) the saving had been only 40.5 per cent. of that of the table, it was 49.2 per cent. for 2.5 in. (0.340 in. per ft.) slope. A decrease of

Jan 1, 1910

By Franz R. Dykstra, R. F. Tatnall

A ferroalloy is defined as: "An alloy of iron with some element other than carbon used as a vehicle for introducing such an element into the manufacture of steel. The element may alloy with the steel by solution or, as the carbide, -neutralize the harmful impurities, by combining with them and separating from the steel as flux or slag before solidification."a The most commonly used ferroalloys are: ferromanganese, ferrochrome, ferrosilicon, ferrovanadium, ferromolybdenum, ferronickel, ferrotungsten, ferrocolumbium, and ferrophosphorus. Concern here is with the sources and markets of the major metallic alloying elements. The discussion is further restricted to those - ferroalloy ores, the principal use of which is in the production of steel. Phosphorus, silicon, and tungsten, for example, are ferroalloys of some economic significance, but other uses dwarf their alloying applications. Thus, this discussion will deal with the ores of managanese, chromium, nickel, molybdenum, vanadium, and columbium. As shown in Table 14.1B.1 ferroalloys serve to- facilitate processing and impart to the finished steel such characteristics as tensile strength, ductility, low-temperature impact, hardenability, high-temperature strength, corrosion resistance, toughness, and abrasion resistance. In the steel-making process, ferroalloys may be added in the charge, in the molten bath near the end of the finishing period, in the ladle, or in the molds. Timing of the addition depends on the effect of the addition on the temperature of the molten metal, the formation and elimination of reaction products, and the protection of subsequent additions from oxidation. MANGANESE General Approximately 95% of the manganese ore sold is consumed by the steel industry, either as ferromanganese or as manganese metal. Manganese is the universal alloy, without which good steel cannot be made. It serves as a scavenger, removing phosphorus, sulfur and, to a degree, oxygen from the melt. As an alloying material it makes steel hard, tough, and resistant to wear. Approximately 6 kg of manganese is required for every ton of common steel produced by United States steelmaking practice. The remaining 5 % of the manganese ore consumed consists of special or so-called "chemical" ores, including high-grade pyrolusite ores, electrochemically reactive "battery ores," and a number of special varieties, as well as those otherwise regarded as "metallurgical ores."

Jan 1, 1976

By R. J. Wysor

J. S. UNGER, Pittsburgh, Pa.-On page 22 reference is made to 36 carloads .of dust shipped. Did the material in that last sample come from a; furnace running on pig iron, ferro alloys, or spiegel? R. J. Wysor.-Pig iron; we have not made any ferro alloys; or spiegel at Bethlehem in the last 3 years. J. S. UNGER.-DO you use domestic or foreign ores? R. J. WYSOR.-In regular practice, largely foreign ores. J. S. UNGER.-How much per unit does it cost to produce that? R. J. WYSOR.-You might say it does not cost anything; we do not change our blast-furnace practice at all to obtain the dust. Although it has been a profitable byproduct, I would rather not have it unless we could reclaim it on a large scale, as we would have better working stoves. J. S. UNGER.-Does the trade take it as readily as natural salts? W. J. WYSOR.-The fertilizer dealers have been anxious to get it. This did not happen, however, until the war started. J. S., UNGER.-They have been willing to take anything since the war started. R. J. WYSOR.-Yes. However, we could have sold the material before the war; in fact, about 4 years ago, we had a contract ready to sign, but we did not think it would pay us to bother with it then. W. H. Ross, Washington, D. C.-We of the Fertilizer Division of the Bureau of Soils have been particularly interested in Mr. Wysor's investigations on the possibilities of recovering potash from the blast furnace, and we look upon the results he obtained as among the-most important that have yet appeared on the subject of finding new sources of .American potash. About 5 years ago we undertook a corresponding investigation on the recovery of potash in the cement industry. Representative samples of raw mix and ground clinker were collected from the different cement plants in this country with a view to analyzing each sample for potash. With the data thus obtained and knowing the ratio between the raw mix and the cement produced and the output of the latter, we thought it possible to calculate approximately for each plant the quantity of potash that escapes daily from the kilns. After partly completing the work, however, it had to be abandoned for a time. It was again taken

Jan 4, 1917

By C. E. Lesher

Coal has been fighting a rear-guard action since the last World War. The battle against competitive fuels has been largely guerilla warfare with more sniping within the ranks than of organized opposition. Oil and natural gas are the fuels that over these twenty odd years have driven coal backward and out of many profitable markets. Now, somewhat timidly, the coal industry is trying a new weapon; namely, Research, or let us more properly say, Organized Research. Engineers have been designing this weapon for many years, supported by those interested in coal, including some coal producers. A part of this pioneer work has been Fundamental Research, the Ph.D. kind that is over the heads of most of us. Another part has been aimed at immediate objectives and realizable profits, the practical, man-in-the-street sort. That is Industrial Research. Enough has been accomplished to make a fair exhibit, but whether this new weapon will have sufficient fire power to rout the opposition, whether the industry will really go into production and use it, the next few years will tell. Need foR Coal Research To utter "Research" is to use the modern magic word; to conjure up the miraculous—rubber from weeds; radar; magnesium from sea water; yes, even gasoline from coal. Research is a very general term. It means something different to every man. What is the coal industry seeking with its research; or what should it seek? And, specifically, how is it going about the job; and is it taking the best way? There are many who say that Coal has been asleep at the switch, while Oil and Gas have been taking the energy business. In an organized way this is true. Large-scale, privatelyfinanced research is just started in the Pennsylvania anthracite industry, and it is still a dream for bituminous coal. What has been done so far collectively is purely defensive; as, for instance, to improve mechanical devices for burning coal so as to be able to recover markets for house-heating fuel long since abandoned to oil and gas. To appreciate just how seriously bituminous coal has slipped back in the national economy in the past 2 5 years, one has only to recall that, in the last war the Navy required for its operations all the high-grade, low-volatile coal that could be produced, and that anthracite was withdrawn from the middle and northwest markets to keep the eastern seaboard warm. All coal was "rationed" by zones, if not to individuals. Now the Navy, the Armed forces and the Merchant Marine are propelled by oil and gasoline. Gasoline and heating oil are rationed to individuals. Production of all coal in this country in 1918 reached the historic figure of 678,200,-000 tons, and in 1943, after 25 years, it is expected to reach a special wartime total of 660,000,000 tons. Meanwhile, production of crude oil this year may exceed 1 ,500,000,000 bbl., and like that of natural gas, reach four times the amount produced in 1918.

Jan 1, 1944

By C. E. Lesher

Coal has been fighting a rear-guard action since the last World War. The battle against competitive fuels has been largely guerilla warfare with more sniping within the ranks than of organized opposition. Oil and natural gas are the fuels that over these twenty odd years have driven coal backward and out of many profitable markets. Now, somewhat timidly, the coal industry is trying a new weapon; namely, Research, or let us more properly say, Organized Research. Engineers have been designing this weapon for many years, supported by those interested in coal, including some coal producers. A part of this pioneer work has been Fundamental Research, the Ph.D. kind that is over the heads of most of us. Another part has been aimed at immediate objectives and realizable profits, the practical, man-in-the-street sort. That is Industrial Research. Enough has been accomplished to make a fair exhibit, but whether this new weapon will have sufficient fire power to rout the opposition, whether the industry will really go into production and use it, the next few years will tell. Need foR Coal Research To utter "Research" is to use the modern magic word; to conjure up the miraculous—rubber from weeds; radar; magnesium from sea water; yes, even gasoline from coal. Research is a very general term. It means something different to every man. What is the coal industry seeking with its research; or what should it seek? And, specifically, how is it going about the job; and is it taking the best way? There are many who say that Coal has been asleep at the switch, while Oil and Gas have been taking the energy business. In an organized way this is true. Large-scale, privatelyfinanced research is just started in the Pennsylvania anthracite industry, and it is still a dream for bituminous coal. What has been done so far collectively is purely defensive; as, for instance, to improve mechanical devices for burning coal so as to be able to recover markets for house-heating fuel long since abandoned to oil and gas. To appreciate just how seriously bituminous coal has slipped back in the national economy in the past 2 5 years, one has only to recall that, in the last war the Navy required for its operations all the high-grade, low-volatile coal that could be produced, and that anthracite was withdrawn from the middle and northwest markets to keep the eastern seaboard warm. All coal was "rationed" by zones, if not to individuals. Now the Navy, the Armed forces and the Merchant Marine are propelled by oil and gasoline. Gasoline and heating oil are rationed to individuals. Production of all coal in this country in 1918 reached the historic figure of 678,200,-000 tons, and in 1943, after 25 years, it is expected to reach a special wartime total of 660,000,000 tons. Meanwhile, production of crude oil this year may exceed 1 ,500,000,000 bbl., and like that of natural gas, reach four times the amount produced in 1918.

Jan 1, 1944

By Arthur B. Cummins, Henry Mulryan

DIATOMITE is a hydrous or opaline form of silica, commonly known as diatomaceous earth, diatomaceous silica or kieselguhr. The term "infusorial earth" has lost its original meaning and today is incorrect in view of the distinctions between diatoms and infusoria. Various locality and variety names are obsolete but some retain local significance. Moler and Celite are trade names that have become associated with diatomite products from certain deposits in Denmark and near Lompoc, California. COMPOSITION Diatomite is essentially silica with some combined water (2 to 10 pct). Frequently it contains organic matter (from traces up to over 30 pct) and varying amounts of inorganic impurities such as sand, cryptocrystalline silica, clay, volcanic ash, calcium carbonate, magnesia and soluble salts. In the natural or crude state, diatomite contains from 10 to 65 pct or more of free water. Table I gives analyses of several diatomites from deposits of different types. PROPERTIES Pure varieties, either massive or stratified, are friable and porous, of low apparent density, and somewhat chalklike in appearance. Varieties containing organic matter vary from sedimentary oozes to peatlike materials. Impure varieties may be more or less claylike, sandy, calcareous or cherty. Compacted types approach porcellanite and silicified shales. COLOR-white, cream, gray, tan, brown, greenish to nearly black. HARDNES-light-weight varieties appear 1 to 1.5 because of porosity, but microscopic particles are 4.5 to 6.5. SPECIFIC GRAVITY-1.9 to 2.35. APPARENT DENSITY---dry block form, 20 to 40 lb per cu ft; dry powder, 5 to 16 lb per cu ft. CRYSTAL SYSTEM-generally amorphous (isotropic by X-ray diffraction) but frequently showing faint cristobalite pattern.67.68,70 MELTING POINT-1400° to 1650°C. STREAK-white. LUSTER

Jan 1, 1949

By Ronald J. Roman

Research pertaining to flow of solutions in leach dumps has generally been neglected. This technical note proposes a method for evaluating the flow patterns and incorporating the results into dump-leaching models. Three dump-leaching models1-3 have been proposed to scale up laboratory test data to expected field results. These models are based on the same physical picture in a dump and differ only in the importance of diffusion or surface chemical reaction rate. Selection of this rate-controlling phenomemon is based on type of ore (sulfide or oxide), physical dimensions of the particles being leached, and the leach heap itself. All three models are applicable to specific types of operations. The models are similar in the use of a size distribution analysis for the dump material and the assumption that the leach solution flows around each particle. Transport of the leaching agent to the interior of the particle takes place by diffusion [(Fig. 1)]. However, normal dumps are of a higher bulk density than the material in a laboratory column used to generate the scale up data. How does this difference in bulk density affect the scale up equations? Increasing the bulk density can be expected to give more particle-to-particle contact; therefore, individual particles will be blinded by each other. As blinding increases with bulk density increase, the particles will behave like larger particles with a coarser apparent size distribution. The extreme will occur when the bulk density reaches that of the undisturbed rock, the entire dump behaving as a single particle with the dimensions of the heap itself. Harris4 alluded to this phenomenon in his paper. An alternative method of describing the same phenomemon is to consider the flow paths of the solution. At high bulk densities leach solution no longer surrounds each particle, but flow paths are separated by several particles and channeling is said to take place. Instead of the particle radius being the maximum distance through which the leaching agent must diffuse, the maximum distance is half the separation distance of the solution flow path. Particle size distribution must then be replaced in the models by the concept of channel separation distribution. Like size distribution, channel separation distribution specifies the cumulative percentage of the rock in the dump situated less than a specified distance from a solution channel. Thus, [ ] Distribution of the solution channels is a function of how the dump was built (among other things), and therefore it cannot be determined in the laboratory. Accordingly, it becomes necessary to determine a range for d and a in existing operations or measuring these parameters before leaching starts. Howard5 gives a clue to one possible technique of measuring solution channel distributions. When his paper was published little was known about the phenomemon of leaching; the importance of this type of data was not recognized. [Fig. 2] is a Y-Y log for one hole drilled

Jan 1, 1978

By C. A. Queener, W. L. Mitchell

In recent years bismuth telluride has received considerable attention, primarily due to its value as a thermoelectric material. Since there seems to be little dependence of thermoelectric effect upon crystal orientation1 many of those who have previously worked with this material have been unconcerned with knowing its crystallographic angles to any degree of accuracy. However, when one studies deformation modes, lattice stresses, or the aniso-tropy of mechanical properties of a material, knowledge of the interplanar angles and their relationships as depicted in a stereographic projection becomes essential. Lange2 originally published crystallographic data which described the structure of bismuth telluride as rhombohedral with the space group A more recent work by Francombe3 presented data which corroborated and refined the original findings of Lange. In addition, Francombe established that there is no coexistence of rhombohedral and hexagonal lattices in bismuth telluride as was suggested by Vasenin and Konovalov,4 and that the structure can be treated as a pseu do hexagonal structure with an axial ratio, c/a, of 6.95 for convenience of presentation and study. The interplanar angles and standard projections for several unalloyed hexagonal metals have been previously published,5-9 but the present work appears to be unique in that it presents data for a rhombohedral compound in pseudohexagonal form. As a pseudohexagonal structure, this material has an extremely large axial ratio as compared to the usual range of approximately 1.5 to 1.9 for the hexagonal metals. Since the interplanar angles are a function only of c/a, the angular relations between various planes for Bi,Te3 will be grossly different

Jan 1, 1965

By George C. Stone

The stack gases from regenerative furnaces lare very seldom utilized for the production of steam. If the temperature of the gases is not higher than 300" C. (572" F.) there is no economy in their use for this purpose, as the amount of available heat is very small and the temperature is so little above that of the steam that the interchange is too slow. With higher temperatures of the waste gases, however, good results can be obtained. At the plant of the New Jersey Zinc Co. (of Pa.) at Palmerton there are a number of return tubular boilers, each 6 ft. in diameter and 20 ft. long, with 96 3.5-in. tubes, which are heated by the waste gases from the spelter furnaces. These furnaces have continuous regenerators heating the air only and the stack gases reach the boilers at a temperature of about 450". The gas producers for one of these furnaces require 14 tons of anthracite (a mixture of Nos. 2 and 3 buckwheat), and the waste heat from the furnace gives a little more than 42 h.p. in steam. The boilers are not well adapted for the purpose, as they are much too large for the amount of heat going to them and the area of the tubes is not sufficient to take the gas from two furnaces without causing an objectionable amount of back pressure. The plant was built without any idea of using waste-heat boilers, and it was impossible to place the latter as close to the furnaces as they should be. Furnace and boiler are connected by an underground brick flue in which the temperature of the gas drops about 100°, losing 40 per cent. of its available heat. If the boilers were close to the furnaces the horse power of each would be 70 instead of 42. Even under these unfavorable conditions the boilers have been very advantageous, as one boiler easily supplies the steam necessary for two batteries of producers. With such low gas temperatures the heating surface of the boilers is, of course, not as efficient and the flue areas need to be considerably larger than for coal firing.

Jan 1, 1914

By D. E. Wolfson, H. J. Gluskoter, M. R. Geer, John A. Harrison, H. F. Yancey, I. S. Latimer

When this chapter was prepared for the kst edition in 1942, continuous mining machines virtually were unknown, and hand loading in underground mines, which gave an opportunity to discard impurities, accounted for 55 percent of the production of bituminous coal and lignite as compared with the 1965 figure of 11 percent. Only 24 percent of the total production was cleaned mechanically, compared with the present (1965) figure of 65 percent. The amount of refuse discarded during preparation for the same period increased from 13 to 21 percent. Changes in the equipment used in the cleaning process were as follows: [ ] Unclassified nearly 8 percent. Data on the amount cleaned by flotation was not collected until 1960 when 1.8 million net tons was so treated. In 1965 this figure increased to 6.9 million tons. Although the great increase in mechanization and full seam mining has resulted in substantial increases in the impurity content of the raw coal as well as in a finer size consist, some phases of face preparation are still important, particularly the variability of the distribution and thickness of the interbedded impurities and the changes in the character of the roof and floor from place to place in the mine. Knowledge of these factors in relation to all phases of the mining operation, particularly selective mining, are still of importance to the treatment of raw coal in the preparation plant. The major characteristics of coal and impurities from the standpoint of mechanical cleaning are particle size composition, generally called size consist, density differences, the relative friability of the coal and of its associated impurities, hardness, and strength. Some of the other factors related to preparation are petrographic composition and rank. COAL PROPERTIES Rank Perhaps 95 percent or more of the coal cleaned mechanically is of bituminous rank. Only a very small tonnage is subbituminous and prac-

Jan 1, 1968

AT the Wednesday morning session on Mine Ven-tilation, D. Harrington's report of the committee on metal mine ventilation was presented. He said the only paper which had been received was one from Nevada, although a number had been promised. Mr. Harrington gave instances from his experience where it had cost less to operate ventilating fans during idle periods in mines than the expense of replacing timber, which was destroyed by fungus during the period when the mines were not ventilated. He referred particu-larly to a metal mine in Michigan and a copper mine in the Southwest where this condition had been found in parallel tunnels, one of which had been ventilated after work had ceased and the other had not been. Mr. Harrington also referred to the fumes after blasting operations in mines operating in large bodies of sul-fide ores. By installing mechanical ventilating devices, these conditions had been greatly improved. He re-ferred also to a recent instance where an ignition of sulfide ore-dust had resulted in an explosion which killed three men and burned a fourth severely. Methane had been found in some gold mines and also in tunnels for city water-supply, and as a result coal-mine inspec-tion methods had been adopted. In one instance the contractor had changed from 40 per cent gelatine ex-plosive to a permissible explosive. A daily gas sample was taken. Nitrogen had been found in some of the mines, and CO, gas had been found in some of the Cripple Creek mines where a fan had been installed to maintain pres-sure on the working faces. It was found by experiment that the oxygen was absorbed by the rock particles, which led to a relatively greater percentage of CO. Coal-mine splitting ventilating methods had been used in some places. Miners' consumption had been made compensable in Ontario, and there is a large threat-ened charge now standing against metal mine oper-ators in the Province of Ontario. Mr. Harrington re-ferred to some of the literature, especially the recent book on ventilation by W. S. Weeks of the University of California. He suggested, however, that a better title for the book would have been "The Physics and Mechanics of Metal Mine Ventilation," since it was especially valuable in this field.

Jan 3, 1927

By K. G. Davis, P. Fryzuk

VALUES for the equilibrium distribution coefficient, ko, are required for solidification studies. The procedure generally adopted1-3 is to progressively solidify alloy rods over a range of growth rates, under conditions where a high degree of convective mixing is present in the melt. The measured effective distribution coefficients are plotted as a function of growth rate, and the extrapolated value at zero growth rate is taken to be the equilibrium ko. The method is limited by the experimental difficulty in obtaining steady growth rates less than approximately 10-4 cm per sec. Extrapolation from rates greater than this can lead to inaccuracy. In the present investigation, an alternative method for determining ko, previously used by the authors for the Ag-Sn system,' was applied to alloy of thallium in tin. Specimens were grown under conditions where convective mixing was absent, and experimental concentration-distance curves in the region of the initial transient were compared with curves calculated for trial values of ko. The ko which gave the best fit was taken as the correct value. To obtain the calculated curves, a value for the diffusion constant in the liquid near to the melting point was needed. This was determined by the capillary-reservoir method. Diffusion Constants. Details of the experimental procedure used by the authors in the capillary-reservoir technique have been described in previous papers,5'6 the only variation being in the use of Tl204, a ß emitter, as tracer, in contrast to previous work where ? emitters were used. The activity of a ß-emitting sample, as measured in a Geiger counter, is proportional to the surface area. To measure the concentration of thallium along the capillary after diffusion had taken place, the solidified capillary (1 mm diam) was cut into 2.5-mm lengths and each length compressed between parallel steel plates to form a disc approximately 5 mm in diam. The discs were placed in a flat-bottomed dish, covered by a thin lead shield with a central aperture, and counted in a 0 counter with fixed geometry. Each disc was etched lightly in a dilute solution of nitric and hydrochloric acids a short time before counting, to eliminate sur-

Jan 1, 1968

By H. E. Doerr

The writer has been unable to find much information relative to tests made to determine the effect of forging on the specific density of steel. The opinion, however, among men engaged in the business, seems to be that forging greatly compresses or consolidates the steel. While such is doubtless the case with spongy or porous steel, the following experiments indicate that there can be little or no change in the density with steel initially free from cavities. Ten ingots of basic open-hearth steel cast as shown in Fig. 1 were used in the experiments. All the specimens were 0.53 carbon with all other elements the same, the analysis being determined from drillings taken midway between the center and outside of the upper end, as shown in Fig. 2. The specimens were selected from over one thousand ingots so that the tests could be comparative for the work done in forging only, but no two of the ingots were cast in the same heat. Each ingot remained in the mold approximately 30 min., when it was removed and sir-cooled. About 12 hr. later, when the temperature had been reduced to approximately that of the surrounding atmosphere, the head was discarded and the ingot heated in an oil furnace to approximately 2250" F. (1235" C). Approximately 1 min. was required to forge under the steam hammer to 1 1/4 in. (31.75 mm.), rough diameter, as shown by the dotted lines in Fig. 2. All ingots were allowed to air-cool after forging. Cylinders 1/2 in. (17.7 mm.) in diameter and 1/2 in. high were then turned from the forged and unforged parts of the ingots and numbered. The ten pairs of specimens were submitted to Louis E. Endsley, Professor of Railway Mechanical Engineering, University of Pittsburgh; A. N. Talbot, Professor of Applied Mechanics, University of Illinois; L. Z. Slater, chief chemist, Scullin Steel Co., St. Louis, Mo. NO information was furnished as to which specimens were forged or unforged and each laboratory used the same specimens, submitting the average of three independent determinations, a tabulation of which is shown in the accompanying table in which the laboratories are designated by the letters A, B, and C. While there is considerable difference in the individual determinations for a number of the specimens, the averages

Jan 1, 1920

The Gooseberry Mine is located 38 krn (24 miles) by road east of Reno, 13 km (8 miles) south of Interstate 80. The mine was originally discovered in 1906 and remained in the control of the Martin family of Fresno, who worked the-property with Mexican ranch hands for 68 years. Westcoast took over the property in 1976 from Apco Oil Corporation. During the time the Martins operated the mine, a 305 m (1,000 ft) inclined shaft was sunk with drifts developed on eight levels exceeding a total of 3,000 m (9,000 ft) in length. It is interesting to note that for over one -half century all development ore was stockpiled. West- coast, the United States mining subsidiary of Home Oil Company Ltd., Calgary, Alberta, completed sinking another vertical shaft to the 396 m (1,300 ft) level. Development work between 122 m and 305 m (400 ft and 1,000 ft) levels has proved the existence of a fine ore body over 300 m (1,000 ft) long. The silver-gold ore grade is fairly consistent in the vertical section, but copper, lead and zinc may show slight increases with depth. Average width of the ore bearing portion of the vein is 2.5 m (8.3 ft). Stoping is by cut-and-fill method. Average silver values within the ore zone have increased from the 152 m (500 ft) level to the 305 m (1,000 ft) level, although the gold values do show some decrease. It is not possible for the geological staff to predict the depth of the ore. However, several years of ore reserves have been proved in the existing mining areas. Important ore minerals are argentite, native gold, and electrum. Trace amounts of galena, chalcopyrite, and sphalerite are associated with the precious metal mineralization. The vein is mainly composed of calcite and quartz. Mine-run underground ore is dumped from the hoisting skip into a coarse ore bin followed by a jaw crusher, an impact crusher, and a 600 mt (650 st) fine ore bin. The mill has a capacity of 317 mt per day (350 st per day). Two-stage grinding is done by a rod mill followed by cyclones with the underflow sent to a ball mill in closed circuit with the cyclones. Cyclone overflow after conditioning receives a primary float in four 1.7 cu m (30 cu ft) cells and a second stage of conditioning ahead of 24 0.8 cu m (30 cu ft) secondary flotation cells. No cleaning stages are used. Flotation tailings are cycloned for a sand-slime separation with the sands used as underground stope fill and the slime portion to tailing dam storage.

Jan 1, 1981

By Stanley Herold

A FEW notes on the occurrence and significance of mud volcanoes in Colombia may be of interest at the present time, owing to the renewed activity in geological exploration of, the coastal regions bordering the Caribbean Sea. The best-known volcanoes are found a few miles from the seacoast. One is situated to the south of Puerto Colombia; the second, to the east: of Cartagena near the village of Turbaco; and the third, near the village of Puerto Escondido south of the Sinu River. Others. are reported in more inaccessible localities. Usually they stand 2 1/2 or 3 ft. (0.762 or 0.914 m.) above the surrounding ground at the crater, though several craters from 10 to 20 ft. (3.04 to 6.09 m.,) apart will often build up an extensive mound at low gradient. The shallow mound may cover 1/2 or 3/4 acre (0.2 to 0.3 ha.) with an elevation of 12 or 15 ft. (3.65 or 4.57 m.) at the center. The craters are formed of hardened blue clay; the inside diameters vary from 14 to 24 in. (35.56 to 60.96 cm.). The rim is continuous, except on one side where there is usually a cut 3 or 4 in. deep, thus allowing an overflow. The craters are filled to the rim-cut- with a thick mixture of blue clay mud and water, which is kept in agitation by escaping gas. Fig. 1 shows the bubble in the act of bursting and Fig. 2 the appearance of the surface of the viscous fluid a second or so later. The frequency of the explosions is determined by the weight of the column of fluid in the neck of the volcano, consequently, such explosions are not synchronous in a group of craters. Ordinarily, there are two or three explosions in about 3' minutes. The supply of gas is small but steady and sufficient pressure must accumulate before the bubble can enter the column of fluid. The water is derived from the surface and enters the sedimentary strata not` far distant from the volcano. During long dry seasons, as the supply of water fails the volcano dries and geyser action ceases.

Jan 7, 1919

Jerome L. Boyer, Reading, Chairman; William L. Sheafer, Pottsville, Secretary ; Levi Quier, Reading, Treasurer; Robert Allison, Port Carbon; James Archbald, Jr., Pottsville; William Atkins, Pottsville; D. P. Brown, Lost Creek; William McH. Boyer, Rending; Albert Broden, Reading; George Brooke, Birdsboro; Frank Carter, Pottsville; H. P. Cooper, Pottsville ; J. H. Carpenter, Reading; E. S. Cook, Pottstown; B. Halberstadt, Pottsville; Hakon Hammer, Pottstown; J. Hartshorne, Stowe; M. P. Janney, Pottstown; R. C. Luther, Pottsville; N. Muhlenberg, Reading ; W. H. Morris. Pottstown ; George L. Norris, Reading; G. H. Potts, Pottstown ; H. Potts, Pottstown; S. M. Riley, Ashland ; J. S. Robeson, Pottstown ; Jas. P. Roe, Pottstown; A. W. Sheafer, Pottsville; Heber S. Thompson, Pottsville; Bard Wells, Pottsville; E. C.Wagner, Girardville; N. B. Wittman, Birdsboro. Reception Committee.— George Brooke, Chairman; Robert Allison, J. H. Carpenter, Edgar S. Cook, R. C. Luther, W. H. Morris, H. S. Thompson. Hotel Headquarters.—The Neversink Mountain Hotel, near Reading, Pa. All sessions were held in the hotel. The opening session was held on Tuesday evening, October 11. Mr. Jerome L. Boyer, Chairman of the Local Committee, called the meeting to order, and introduced Mr. John F. Daniel], Jr., VicePresident of the Reading Board of Trade, who delivered an address of welcome, in the course of which the industrial and commercial importance of the city was effectively outlined by skilful use of the statistics of leading branches. From this statement the following particulars are condensed for preservation: The Board of Trade has about 300 members. The annual value of the manofttctures (taking mainly the figures of 1891) is as follows: Iron manufactures, about $16,000,000 (including boilers and flues, $323,000; hardware, locks and butts, $1,650,000; pig-iron, wrought-iron pipe and machinery, $8,400,000; beams, bridge-work and steel, $4,000,000; bolts, nuts, rivets, etc., $1,000,000; stoves, $659,000); silk and cotton goods, $1,725,000; boots and shoes (one concern only), $150,000; ropes and cordage, $600,000; fire-brick, terra-cotta and glass, $320,000; wool and fur hats, $3,000,000; cigars (105 millions), upwards of $3,150,000. The street and elec-

Jan 1, 1893

By David B. Rushmore

Torches were used by the early Romans for mine-lighting, and these were followed by open lamps or earthen jars filled with tallow or oil, and later by candles. In early coal-mining, explosive gases seldom occurred, and, if they were encountered, the danger of explosion was materially diminished by the absence of any ventilating-system and the consequent insufficient circulation of air to form with the methane an explosive mixture. As the art advanced, the danger of fire-damp became more apparent, and methods for testing the air were resorted to as early as in the fifteenth century. The method of testing consisted in lowering a dog in a basket down the shaft. As soon as he encountered fire-damp he would commence to howl, after which he was withdrawn, and a leafy bush was fastened to the end of the rope and run rapidly up and down the shaft. This so disturbed the accumulation of gas as to cause it to rise out of the shaft. Later this odd method of testing was improved upon through the discovery that a light inserted in a body of fire-damp Gould produce a blue flame. Candles were used for this purpose, and, when fire-damp was thus discovered, brushing or some other primitive method of fanning was resorted to for driving out the gas. In some instances the gas was burned away, regardless of the danger thereby incurred. A man, wearing a well-moistened coat and a mask with glass spectacles, descended in the mine a few hours before each shift. With a long stick, to which was fastened a burning torch or candle, he would crawl on the floor with the stick so raised that the light would sweep the roof and ignite the gas which it encountered. In this position the flame of the explosion would pass over him, after which he would retreat from the gases resulting from the combustion. The occurrence of serious accidents resulted in

Jan 1, 1913

By Emil Gathmann

Steel as it is poured, or teemed, into the mold for forming the ingot may be broadly separated into two divisions; i.e., effervescing or gassy steel, also termed evolution steel, and non-effervescing or killed steel, also termed solution steel. Between these primary divisions there are various types having the characteristics of both divisions but really nut belonging to either; such steels are termed semi-piping, rising, or wild, as the type may be. True effervescing steel should contain large volumes of gases, which are evolved while the metal is being teemed from the ladle nozzle into the mold, and continue to escape while the temperature of the steel is falling prior to its solidification the top of the ingot remaining liquid, due to the evolution of gases, until an ingot skin of considerable thickness has been formed. These gases consist principally of hydrogen, carbon monoxide, nitrogen, and ammonia. It is generally understood that nitrogen gases are the first evolved and these form the skin blowliolcs, troublesome at times, in the solidifying ingot. Ingots made of effervescing steel will always contain a large number of blowholes. Such blowholes are not deemed objectionable in certain products if they occur well inside the ingot where they will not be subjcct to oxidation upon cooling, reheating, and rolling or forging of the ingot. Very little top or bottom discard is taken from this type of ingot, as pipes, or large shrinkage cavities, at the upper portion of the ingot do not usually occur, the difference in volume between the liquid and the solid steel (6 to 10 per cent.) being compensated by the innumerable blowholes distributed throughout the body of the ingot. Of the 40,000,000 tons of steel made in the United States during the year 1919, at least 35,000,000 tons of ingots were made of gassy or semi-gassy steel. Killed, or solution, steel is termed true piping steel from the characteristic pipe or shrinkage cavity that usually occurs in the uppermost central portion of the ingot.

Jan 1, 1922

By Emil Gathmann

Steel as it is poured, or teemed, into the mold for forming the ingot may be broadly separated into two divisions; i.e., effervescing or gassy steel, also termed evolution steel, and non-effervescing or killed steel, also termed solution steel. Between these primary divisions there are various types having the characteristics of both divisions but really nut belonging to either; such steels are termed semi-piping, rising, or wild, as the type may be. True effervescing steel should contain large volumes of gases, which are evolved while the metal is being teemed from the ladle nozzle into the mold, and continue to escape while the temperature of the steel is falling prior to its solidification the top of the ingot remaining liquid, due to the evolution of gases, until an ingot skin of considerable thickness has been formed. These gases consist principally of hydrogen, carbon monoxide, nitrogen, and ammonia. It is generally understood that nitrogen gases are the first evolved and these form the skin blowliolcs, troublesome at times, in the solidifying ingot. Ingots made of effervescing steel will always contain a large number of blowholes. Such blowholes are not deemed objectionable in certain products if they occur well inside the ingot where they will not be subjcct to oxidation upon cooling, reheating, and rolling or forging of the ingot. Very little top or bottom discard is taken from this type of ingot, as pipes, or large shrinkage cavities, at the upper portion of the ingot do not usually occur, the difference in volume between the liquid and the solid steel (6 to 10 per cent.) being compensated by the innumerable blowholes distributed throughout the body of the ingot. Of the 40,000,000 tons of steel made in the United States during the year 1919, at least 35,000,000 tons of ingots were made of gassy or semi-gassy steel. Killed, or solution, steel is termed true piping steel from the characteristic pipe or shrinkage cavity that usually occurs in the uppermost central portion of the ingot.

Jan 1, 1922