Search Documents

Organization Place _ Date 1919 American Iron and Steel Institute New York, N. Y. May National Fire Protection Association Ottawa Can. May 6-8 American Zinc Institute :.. St. Louis, Mo. May 12 American Association of Engineers Chicago, Ill. May 13-14 Natural Gas Association in America Cleveland, 0. May 20-23 American Institute of Electrical Engineers.... Lake Placid, N. Y. June 24-27 American Society for Testing Materials Atlantic City, N. J. June 24-27 American Institute of Min. and Met. Engineers Chicago, Ill. - Sept. 22-27 American Steel Treaters' Society, First Annual Convention Chicago, Ill. Sept. 22-27 National Safety Council Cleveland, U. Sept. 29-Oct. 2 American Foundrymen's Association Philadelphia, Pa. Sept. 29-Oct. 4 Institute of Metals Division, A. I. M. E Philadelphia, Pa. Sept. 29-Oct. 4 American Ry. Bridge and Building Association Cleveland, 0. Oct. 21-23 Geological Society of America Boston, Mass. Dec. 29-31

Jan 5, 1919

By J. H. Zimmerman

JET-PIERCING experiments were first conducted over ten years ago underground at the Soudan mine of the Oliver Iron Mining Co. Results were successful enough to encourage further research. The next field tests were made on the Reserve Mining Co. property at Babbitt in 1941. These tests showed that blastholes could be produced in taconite ore by the use of a flame and proper fluxing agents. The war put a stop to the experimental program shortly after these tests. Extensive field tests were resumed at Babbitt in 1946. In these tests nominal 6-in. blastholes were produced at an average rate of 10 ft per hour. Rates as high as 17 ft per hour were obtained for short periods. The experimental equipment used resembles a portable rotary-drill rig mounted on a truck. The standard steel mast has been extended to 46 ft to accommodate a blowpipe capable of producing holes over 30 ft deep. All auxiliary equipment including winch for raising and lowering the blowpipe, drive motor for the rotary table, pumps and tanks for process fluids, electric power plant, and control instruments are mounted on the truck. The jet-piercing process consists of

Jan 1, 1948

By Geo. W. Goetz

The following tables show the analyses of ores from nearly all of the mines which will produce over 10,000 tons of ore each during the season of 1890. There are many small mines now in the course of development, some of which may become large producers. Many of the mines produce several different grades of ore, but the analyses given in the tables are fair averages of ore such as the respective mines can deliver. Most of these analyses were obtained from the agents of the respective ores, and are averages of the season of 1889. One can state positively that over 75 per cent. of all the iron-ores of the Lake Superior district will average over 60 per cent. of metallic iron. During the past 34 years this region has produced about 48,137,421 tons of ore, the different districts contributing about as follows: Marquette District,. 29,754,057 Menominee " .10,415,859 Gogebic " . 6,622,194 Vermilion " . 2,342,991 Miscellaneous,. .. .. 2,320 In the year 1889, the product of all the districts was nearly '1,300,000 tons. The product of the entire region for the season of 1890 may exceed 9,000,000 tons. This large amount of ore is shipped to the lower lake ports, from Escanaba, Marquette, Two Harbors and Gladstone.

Jan 1, 1891

By Charles W. Merrill

IF we follow the threads of the mining problems, upon which I have touched, we find them all leading to one great fundamental desideratum. The people of this State, of this Nation, and of this world must be brought to a better understanding of the basic nature of our industry-must be made more mineral-minded. It is my belief 'that there is not a man present among this earnest gathering of those interested in the mining industry, who has not a deep-seated and heartfelt desire that the existing unprecedented welfare and prosperity of the whole mass of American people be maintained not merely through our own generation but through the generations of our children and their children. In the decades to come there can be no question of the keenness of the foreign competition which we are doomed to meet, and in this great international contest that Nation which has the best balanced program of development and that broadness of vision in its governmental direction, which recognizes the necessity of a sympathetic attitude toward the upbuilding of such a broad pro- gram will be the Nation which will maintain and pre- serve that welfare of all of its people.

Jan 1, 1929

By I. N. Knapp

Introduction.-The special object of these notes is to describe the mixing, testing, and use of mud-ladened water for rotary drilling in such a way as to make them helpful to the driller, the operator, or the engineer in solving his own special drilling problems. The structures, apparatus and tools used are indicated in a general way. No attempt is made to describe the art of rotary drilling; only such description as are necessary to make plain the use of mud are given. The information is the result of actual experience in drilling in Coastal Plain formations. The materials encountered in the wells drilled were unconsolidated sands, gravels, and clays, in which thin layers of sandstones, shell conglomerates, and shales began to appear at about 1,200 ft. in depth, although one well was drilled to 3,018 ft. without encountering any cemented or indurated materials. Unusual Conditions.-The general surface of the ground where the drilling was done being hardly a foot above mean tide, and the daily tidal variation being about 15 in., it was found necessary to plank over the sod surface with 3-in. plank to work from. A 30 by 30 ft. planked area was sufficient to carry the derrick with equipment and 2,500 ft. of 4-in. drill pipe stacked in it. The derrick was set up 3 ft. on cribbed blocking arranged to spread the load over the planking. The engine, boilers, and pipe yard were also carried on 3-in. planking. Drilling Outfit.-This consisted of a derrick, 20 by 20 ft. and 84 ft. high, two 35 h.p., "oil country" boilers, one double 8 ¼ by 10 in. reversible engine, two 10 by 6 by 12 in. duplex mud pumps, one 15-in. rotary, "hoisting works" with chain drive, hoisting block with line, crown block with pulleys, rotary' jetting swivels, hose, complement of tools, pipes and connections, and. a mud mixer, with engine.

Jan 12, 1914

By Fred D. Rosi

Introduction There is probably no field in which materials research has played a greater role than that of electronics. However, to trace present and future patterns of materials research in electronics is not an easy assignment, since this industry has a high degree of dynamism in its growth, and is busily engaged today in the scientific improbabilities of only recent yesterdays. On the other hand, this task seems especially appropriate since electronics is a truly frontier industry - one whose place in American industries has advanced from 50th prior to World War II to 6th in 1967, with sales of more than $22 billion. And this growth has been associated with the equally rapid progress of science and technology over the period - in particular with the emergence of materials science as a vital force in underscoring this progress. For several reasons this parallel growth is not too surprising. First, by its very definition electronics is a science that essentially deals with the nature, behavior, detection, generation, control and utilization of electrons in solids or at their surfaces. Second, in the electronics industry, systems are made of an integration of components, and these components with their interconnections are made of materials. Thus, the basic building blocks of systems are materials; and it has been largely the advances in materials research and technology that have led to new and improved devices and systems. It follows, therefore, that the broadening of the frontiers in electronics through the exploration of new territories is tantamount to scientific discovery and materials innovation to a degree found in no other major industrial activity. But to put this in the proper perspective of present and future materials trends, it would be appropriate first to survey historically the progress in electronics by pointing out major scientific discoveries and associated materials research patterns that have led directly to its tremendous growth. Then from this base we can consider recent trends in materials research that could form the basis for future progress in the electronics industry. In my review I shall examine the areas most familiar to me, so I must acknowledge at the outset that this survey is not all-inclusive.

Jan 1, 1971

By J. Murray Riddell

The method of treating hazards wherein value is decreased, is cited by R. D. Parks. Quite properly, the theory of probabilities is made use of when multiple hazards are under consideration. E. F. Fitzhugh, Jr. $ deals with the enhancement phase graphically and uses percentage of expectancy as derived by a study of conditions and the selection of a chance factor. It is believed that both of the authors referred to fully recognize the part which human judgment plays, and as coupled with experience, training, and the application of the theory of probabilities; in that respect the composer of this paper is in accord. Within the past year, the task of arriving at a mathematical method for handling the enhancement phase, and, additionally, coupling the negative and positive phases, was explored. In citing the hazard, or negative phase, reference is made to the text by Parks. Types of Items far Consideration On the hazard, or negative, side some of the common items to be considered are: 1. Subsidence and resulting damage. 2. Flo wage of water above that anticipated. 3. Geological. (a) Decline in quality of probable ore, and/or (b) Decline in quantity of probable ore. 4. Depressed economic conditions. 5. Litigation. Similarly, on the enhancement, or positive, side common items to be considered are: 1. Flo wage of water below that estimated. 2. Geological. (a) Increase in quality of probable ore, and/or (b) Increase in quantity of probable ore. 3. Elevated economic conditions. 4. Litigation. 5. Technological advance in the art. Tn all of the above items no consideration is given to placing a value on, or giving consideration to, possibilities. For example, referring to Table 1, the estimated normal present value (Vp) of a property, exclusive of risk consideration, is taken as $100,000. If subsidence affects the usefulness of the shaft, the present value of the property will decrease to $60,000, and it is judged that there is a 1 in 4 chance that the shaft will be impaired;, consequent.ly, if subsidence took place, the present value would be reduced ($100,000-$60,000) $40,000, but since the chance is 1 in 4, the allowable reduction would be only one-fourth of $40,000, or $10,000, or a discount of 10 pct (hazard factor) of the original value; the related safety factor is taken as unity minus 0.10, or 0.90. Thus, the original Vp, $100,000, multiplied by the safety factor ($100,000 X 0.90) gives $90,000, which is the adjusted present value of the property in this single instance. Additionally, there is a water hazard, which, if encountered, will reduce the present value to $85,000. The chance is 1 in 3. Following through with the same reasoning as shown above, the derived safety factor will be 0.95. To arrive at a single multiplying factor which will express the combined risks, the two safety factors are multiplied together, 0.90 X 0.95 = 0.855. That factor when multiplied by the origirial Vp will give the adjusted, and

Jan 1, 1950

By P. J. Conroy, E. A. Curth

INTRODUCTION In June 1962, the first attempt at longwall mining in Illinois was initiated by Old Ben Coal Company in their No. 21 Mine. Longwalling was continued intermittently using various supports until April 1970. During this period, longwall mining techniques were used on separate occasions at six faces within Mine No. 21. However, due to various problems that developed at each location the faces were eventually terminated. The most significant problems concerned the support systems and roof conditions that were present in the mine during each attempt. Between 1965 and 1972, similar conditions were met by Freeman Coal mining Company during four attempts at longwall mining in their Orient No. 5 and Orient No. 6 mines. In 1975, the U.S. Bureau of Mines and Old Ben Coal Company entered into a cost-sharing agreement to demonstrate the application of longwall mining in Illinois. The first phase of the demonstration was to conduct a premining investigation to review previous attempts at longwall mining, perform rock mechanics tests, and establish support requirements based on the lnvestigation results. The information obtained during the demonstration at Old Ben's No. 24 has been utilized to optimize subsequent face equipment and panel geometry. Mining of the first panel began in September 1976 and was successfully completed in May 1977, and two additional panels were mined under the cooperative agreement. Currently, Old Ben Coal Company is the only longwall mining operator in Illinois. In addition to the face in Mine No. 24, five longwall faces are being operated in four other mines.

Jan 1, 1981

By E. E. Barker

ALTHOUGH flotation was known to be a successful process prior to 1912, Utah Copper Co.'s ores were not entirely treated by this process until 1923. Experiments had been conducted, of course, prior to that time, and in February, 1917, the first unit of the Arthur plant was changed over from gravity concentration to flotation. On May 16, 1918, the entire Arthur plant was on flotation, excepting the coarse concentrate which was tabled prior to fine grinding. The reasons for the delay in adopting flotation at these plants were, first, that it was decided to await the outcome of the litigation with the Butte & Superior Mining Co., which began with an injunction served on Oct. 3, 1911. This litigation continued for years. Then the demands on the plants in the war years 1916, 1917 and 1918, really precluded any further drastic changes during that period, as all efforts were bent on maximum tonnage, and the cry of tonnage, rather than of recovery, was the major issue. The postwar depression followed these years of intensive production, so that it was not until 1922 that the Magna plant was equipped to use this process. Excepting, then, the amount of coarse concentrate that was tabled, 1923 was the first year when the Utah Copper Co.'s ores were on, a full flotation basis. EFFECT OF FLOTATION ON ORE RESERVES The object of this paper is to point out the effect that flotation has had on the operations of the Utah Copper Co. In 1905, when D. C. Sackling began making history in copper, the ore reserves were 34,000,000 tons, with a grade of 2 per cent. copper and a mill capacity of 700 tons daily. The point of cut-off between nonprofitable and profitable grades was 1.2 per cent. A few years later the capacity was increased to 6000 tons, when 1.1 per cent became the point of cut-off. Ore reserves had climbed to 80,000,000 tons, having a grade of 1.9 per cent. In 1911 there was an ore reserve of 300,000,000 tons, with a grade of 1.5 per cent and a cut-off of 1 per cent.; in 1918 the ore reserve was approximately 400,000,000 tons, and a grade of 1.38 per cent., and point of cut-off 0.95 per cent., based on normal costs and prices. Up to this

Jan 1, 1928

LUTHER B. EAMES, Pueblo, Colo. (written discussion*).-In reading Mr. North's interesting paper, several points have been noted that appear to warrant discussion. With a feed all through 20 mesh, I feel inclined to question the use of steel balls as large as 2 in. in a tube mill. I have seen balls as small as-3/4 in. used for the dry grinding of cement clinker, and surely many more points of contact would result from smaller balls. This would seem to be desirable in a mill as short as 6 ft. The heavy load in the classifiers would also indicate a high proportion of returned pulp. I hope that some discussion by Mr. North -and others may develop this point. The flow sheet on page 1181 shows the solution returning from the dam valued at 40 c. per ton being added to the last decantation tank. Theoretically, this solution should not be added to that of a lower value. As I calculate it, if this solution were added to tank X the solution finally discharged from tank Z would be reduced in value by nearly 4 c. per ton.

Jan 10, 1919

By BERNARD PLANNER

PRODUCTION COSTS, profits, and quality are the primary factors in the peacetime production of iron and steel. In a war emergency, as high production rates and as complete utilization of readily available raw materials as possible, consistent with securing passable quality, become the most important factors. In this connection a discussion of some of the recent developments in the German iron and steel industry, where the problem of scarcity has naturally always been more acute than in the U.S.A., maybe of interest. To get more pig iron out of the existing blast furnaces it was necessary to obtain the maximum efficiency from the iron-bearing raw materials. This was achieved by eliminating all "excess baggage," chiefly by beneficiating the ore. The preparatory work for this was done by various methods which are effective when the ore either is too poor or contains too many impurities or too much gangue. Some of the beneficiation methods are well known, some are combinations of wet-mechanical, magnetic, roasting, sintering, and other treatments.

Jan 1, 1942

By Richard M. Foose

FIVE miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. GEOLOGY Lower Cambrian Antietam quartzite and the Montalto quartzite, stratigraphically older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65° to vertical. The clay crops out at an elevation of about 1000 feet. ORIGIN AND CHARACTER The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about l00 ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: Si02, 67.05 per cent; A1203, 22.27; Fe203, 0.40; CaO, 0.00; Ti02, 1.05; MgO, 0.52; Na20, 0.04; K20, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1944

By F. R. Cattoir, R. W. Kimball, C. T. Anderson, V. V. Donaldson

THIS paper is the second of a series on the effect of various elements on hot-working characteristics of Fe-C alloys to be issued by this laboratory. The investigations being conducted at the Ferroalloy Research Branch of the U.S. Bureau of Mines, Redding, Calif., involve fundamental research on the effects of various alloying materials and impurities on the physical properties of high purity Fe-C alloys. This paper deals with the determination of the limit of forgeability of steels containing varying amounts of manganese and sulphur. A paper discussing the hot-working characteristics and the physical properties of the forgeable alloys is being prepared. One of the principal impurities in all steels is sulphur.. The phenomenon, hot-shortness, commonly attributed to sulphur, has long been a source of expense and inconvenience to both the maker and user of steels. In steelmaking practice, this effect of sulphur has been overcome by the addition of manganese which, apparently, acts as a desulphurizer. Manganese is also used as a deoxidizer and alloying material. The critical and strategic position of man- ganese gives added importance to research which may contribute to its conservation and more effective utilization. It is not the purpose or intention in the present paper to give any explanation of the mechanism of either hot-shortness or its prevention but rather to report the results of forging high purity Fe-C alloys of the range of compositions near the limit of hot-forgeability. Temperatures for each phase of reduction were duplicated within 20" to 30°F for all tests. The starting material was sponge iron, which, after melting and purification, gave a high purity iron containing about 0.001 pct each of silicon and phosphorus. Scrap iron was not considered suitable because of its high percentage of contaminants and wide variation in analyses. The sponge iron was melted and refined for melting stock in a three-phase, direct-arc, size ST, Moore Rapid Lectromelt furnace with a 500 kva rating as described in the preceding paper. Additives were carefully selected to avoid addition of contaminants. The sulphur was added as resublimed flowers of sulphur or purified roll sulphur of analytical grade. The manganese used was dehydrogenated high purity electrolytic material produced by the Bureau of Mines plant at Boulder City, Nev. High purity aluminum in the form of wire was used for deoxidation. The limestone was obtained locally and had the following analysis: CaO, 53.7 pct; MgO, 0.8; ignition loss, 42.4; R2O3, 0.2; SiO2,3.0; and P2O5, 0.014.

Jan 1, 1955

By Harrison Souder

MAGNETITE mining and milling in the Eastern States showed continuing improvement during the year. Some of the smaller mines remained idle, but the larger operations responded promptly to the improved situation in the iron and steel industry. The output of ore for 1936 was over twice that for 1935. A number of improvements were made in mine plant and equipment, and operating forces were increased and maintained at near normal. The coming year should see additional mines started up and production increased at the larger properties.

Jan 1, 1937

By H. E. Doerr

THE writer has been unable to find much information relative to tests made to determine the effect of forging on the specific density of steel. The opinion, however, among men engaged in the business, seems to he that forging greatly compresses or consolidates the steel. While such is doubtless the case with spongy or porous steel, the following experiments indicate that there can be little or no change in the density with steel initially free from cavities: Ten ingots of basic open-hearth steel cast as shown in Fig. 1 were used in the experiments. All the specimens were 0.53 carbon with all other elements the same, the analysis being determined from drillings taken midway between the center and outside of the upper end, as shown in Fig. 2. The specimens were selected from over one thousand ingots so that the tests could be comparative for the work done in forging only, but no two of the ingots were cast in the same heat. Each ingot remained in the mold approximately 30 min., when it was removed and air-cooled. About 12 hr. later, when the temperature had been reduced to approximately that of the surrounding atmosphere, the head was discarded and the ingot heated in an oil furnace to approximately 2250° F. (1235° C). Approximately 1 min. was required to forge under the steam hammier to 1 ¼ in. (31.75 mm.), rough diameter, as shown by the dotted lines in Fig. 2. All ingots were allowed to air-cool after forging. Cylinders ½ in. (17.7 mm.) in diameter and ½ in. high were then turned from the forged and unforged parts of the ingots and numbered. The ten pairs of specimens were submitted to Louis E. Endsley, Professor of Railway Mechanical Engineering, University of Pittsburgh; A. N. Talbot, Professor of Applied Mechanics, University of Illinois; L. Z. Slater, chief chemist, Scullin Steel Co., St. Louis, Mo. No in-formation was furnished as to which specimens were forged or unforged and each laboratory used the same specimens, submitting the average of three independent determinations, a tabulation of which is shown in the accompanying table in which the laboratories are designated by

Jan 1, 1919

By Sheldon P. Wimpfen

EVERYWHERE in mining circles the talk is of this new development of hard faced or insert bits which hints of many changes to come in mining practice and rock drill equipment. In the past fifteen years new equipment has appeared in rapid succession which brought one change after another in rock breaking practice. Detachable bits were an innovation which met with wide success. Blasthole diamond drilling has proven itself. Only recently, fusion piercing was announced as a possible solution to the problem of breaking taconite ores. For several years this interest in new methods has been growing and various experimental usages of tungsten carbides in rotary type rock drilling bits have been partially successful. American experts in rock drilling have been concerned with the subject for ten years but actual commercial practice was begun by European manufacturers and mining companies. At this time nearly every manufacturer of rock drilling bits is working on some type of an insert bit. On the Rand, European manufacturers are testing out various types of insert bits. The problems relating to rock drilling in South Africa vary greatly from ours. The bulk of the drilling there is limited to the 31/2-ft holes that are drilled for breaking the gold bearing reef ore. Rock drilling in most mines is far more diversified. Both drifting and ore breaking call for holes varying in length from 4 ft up to as much as 50 ft and more.

Jan 1, 1947

By Carl Beal

THE most important factors that should be given consideration in valuation of oil land are: (1) the amount of oil the property will produce; (2) the amount of money this oil will bring (based upon the future prices of oil) ; (3) development and production costs; (4) the rate of interest on the investment; (5) the retirement or amortization of invested capital; and (6) the salvage or "scrap" value of the equipment when the property is exhausted. These factors are of varying importance, and some of them may not enter all valuation problems, but most of them should be given consideration in any valuation even though only a rough estimate of the value of the property is desired. The value of a property may be changed over-night by the completion of important test wells, by the sudden water flooding, or by a change in the price of oil. The best a petroleum engineer can give is the value of the property under the conditions existing at the time the appraisal is made with a fair forecast of future action of the wells and of the price of oil. Our experience in the scientific valuation of oil lands is not broad and there is very little published information on the subject; it, therefore, becomes necessary in studying such problems to form comparisons with the factors involved in the valuation of mines-the closest parallel. One of the reasons for the lack of substantial progress in oil-land valuation methods has been the necessity of making an estimate of the future production of the oil property to be valued. Oil men and accountants have not generally conceded that such estimates could be made with any degree of accuracy. It has been shown, however, in several recent publications that with certain data available reasonably close estimates can be made. The accuracy of an appraisal depends chiefly on the accuracy of the estimates of future production and of the future price of oil. The accuracy of the former is sometimes necessarily based on geological inferences. Geology is not an exact science and geological data in connection with oil production cannot always be mathematically evaluated.

Jan 9, 1919

By M. R. Todd, J. Szekely

THE mechanism of carbon oxidation in steelmaking processes has attracted considerable attention in recent years. The generally accepted model postulates that the reaction between carbon and oxygen occurs at the surface of CO bubbles that originate at the suitable nucleation points and subsequently rise through the metal bath.1-4 Although this model describes adequately the behavior of open-hearth type operations, it is not a satisfactory representation of carbon oxidation in oxygen steelmaking processes since it cannot account for either: i) the very high rate of oxidation per unit bath area,or ii) the commonly reported shapes of the curves showing the dependenie of the oxidation rate on the carbon concentration. The very high decarburization rates commonly encountered in oxygen steelmaking processes need no further elaboration; some typical plots of the rate of carbon removal against carbon concentration, taken from a publication by Li, Dukelow, and smith,' are reproduced in Fig. 1. It is seen from the curves that the decarburization tends to decrease from a peak or a plateau once the carbon concentration falls below a certain value; in the experiments reported, this critical value ranged from 1.2 to 0.2 wt pct C. The apparent dependence of the decarburization rate on the carbon concentration indicates that within this region phenomena associated with the transfer of car- bon must play an important if not predominant role. Since the concentration of oxygen in molten iron at steelmaking temperatures (removed from the immediate impact zone) is only about 0.1 wt pct,6 it is clear that simple simultaneous diffusion of carbon and oxygen to the surface of CO bubbles could not account for the rate of carbon transfer being the controlling step at carbon concentrations as high as 1.0 wt pct. The purpose of this communication is to present an alternative model which may explain at least qualitatively the apparent anomalies mentioned and may stimulate further experimental work. The Physical Model. It is suggested that the principal mechanism of decarburization is the reaction between CO bubbles and an emulsion consisting of molten iron and molten iron oxide particles in the vicinity of the "slag-metal interface9'.* This mech-

Jan 1, 1968

By S. W. Parr, A. R. Powell

FOUR general methods have been used in the study of the decomposition of coal. The first has been directed toward the processes of coal formation, the second has been by means of microscopic studies, the third from the data of destructive distillation, and the fourth has made use of various solvents. Applying these methods to the sulfur of coal, it has been found that the organic sulfur of plant and animal life enters into the formation of coal and remains in organic combination in the final product. The inorganic sulfur is almost entirely combined as iron pyrites and marcasite. The infiltration of hydrogen-sulfide waters is doubtless a large factor in these combinations. Sulfates are found in very small quantities except where free oxygen has entered the coal strata. The mechanical mixing of detritus with the early coal material is another source of sulfur. In this case the sulfur is distributed in microscopic particles throughout the mass. In destructive distillation, a part of the sulfur comes off as hydrogen sulfide and various thiophen compounds, but this furnishes little information as to the nature of the sulfur compounds in the coal itself. The use of solvents has given valuable data concerning the sulfur compounds in coal. Fremyl and later E. Guignet2 noted the action of alkaline solutions on coal after treatment with nitric acid and Anderson and Roberts3 showed the presence of large quantities of organic sulfur in the extract so obtained. In a study of the phenol extract of coal, Parr and Hadley4 found organic sulfur in the soluble organic material. These investigations proved the presence of organic sulfur in coal in addition to the inorganic forms, such as iron pyrites and sulfates. T. M. Drown6 attempted the analysis of the pyritic and sulfate sulfur as distinct from the organic forms by means of sodium hypobromite; no definite proof of

Jan 1, 1920

By T. M. Girdler

INDUSTRIAL progress and development in this country from the earliest daps to the present has proceeded at an ever-quickening pace. Yet during recent decades the nature of our industrial progress and development has undergone a change of great significance. The earlier days were a period of tremendous expansion. Population was increasing by leaps and bounds. Vast areas of new land were being .2 opened to settlement. And almost boundless new sources of timber, coal, oil, ores, and power were being opened to ever-expanding markets. Today, however, that picture has al- most completely changed. Today, with population increase tapered way off and the opportunity for free expansion into western frontiers gone, the great industrial development of our country continues on a vastly different front. Industrial progress and development today rest on a foundation of technology. The key- stone is research. Our frontiers to- day are frontiers of sciencec

Jan 1, 1939