Search Documents

G. W. TRAER (author's reply to discussion*).-Prof. Parr's discussion develops two points, upon which it seems desirable to comment. First, as to putting through a large enough tonnage to secure economic operation. At each manipulation of each oven 1500 1b. (680 kg.) of coal will be charged and the resultant coke discharged from a like amount of coal. . Sixteen slabs will be discharged at each manipulation, each approximately 5 ½ in. by 11 in. by 6 ft. (14 cm. by 28 cm. by 1.8 m.). The operating schedule of a commercial plant, based upon our observations and calculations, indicates a "through put" of at least 12 tons of coal per day for each oven. We have made these figures conservatively and feel confident of materially exceeding them in a fully developed operating system. Our oven plant, with containers, will not cost as much as high-temperature plants of the same capacity. They do not require container equipment; but this is much more than offset by the cost of the great basal heat regenerative flues. Our operating requirements are quite susceptible to the application of mechanical devices and we believe our labor cost will be well within the necessary limit. Second, as to Fig. 1 in my paper, showing the specific gravity' of the tar. It Was not intended to show that the specific- gravity of -the tar rises With decreasing heat, since of course the contrary is the fact. One of the curves shows the relation between temperature and specific gravity and the other the relation between temperature and- yield. Our consulting engineer prepared the chart according to his customary method for showing two dimensions.

Jan 1, 1919

By F. C. Oliphant, George H. Fancher

Two samples of drilling mud from the Hastings oil field, Texas, were tested, and the solids in each were separated into small fractions of a limited range in particle size. The mineral composition of each fraction by X-ray analysis is reported, and the results are interpreted in relation to other measured quantities, such as the physical properties of the original samples and the density of the various fractions. It was found that only 7 to 8 per cent by weight of the solids was of colloidal dimensions and that neither of the samples contained montmorillonite but did contain illite. Considerable calcite was also found. These data should be useful to the geologist interested in the origin and history of sedimentary strata as well as to the petroleum engineer. Introduction The questions, What is good drilling mud? What constitutes bad drilling mud? are pertinent, because the proper use and control of drilling fluids has been a factor of great importance in the successful drilling and completion of oil wells since the days of Captain Lucas. Adequate control of the characteristics of drilling fluids has assumed greater significance comparatively recently because of the problems introduced by caving formations in deep wells, costly blowouts and impressive mud bills. Much is known about the solution of some of the problems but, despite extensive research directed toward a better understanding of the physical and chemical properties of clay suspensions, it is difficult to define precisely a drilling mud, and much more difficult to say what constitutes a good mud. It is generally believed that the smaller particles of a drilling mud greatly affect its physical properties. In fact, it is customary to blame the colloids in a mud for nearly everything that goes amiss, because colloidal properties have effects out of all usual proportion on viscosity, filtration rate and reaction to electrolytes. It is germane to know whether drilling muds possess colloids and if so, the quantity and kind. Source oF Samples Two drilling muds from the Hastings oil field, Brazoria County, Texas, were selected because it is generally agreed that in this oil field good natural muds made solely from formations penetrated by the drill can be used until the well is nearly ready for completion. Customary drilling procedure in this field is to spud in with water, set a protective string of pipe, drill to 2500 ft. and set the surface casing. Drilling is continued to 5500 ft. with no treatment of the drilling fluid other than addition of water to

Jan 1, 1943

By F. C. Oliphant, George H. Fancher

Two samples of drilling mud from the Hastings oil field, Texas, were tested, and the solids in each were separated into small fractions of a limited range in particle size. The mineral composition of each fraction by X-ray analysis is reported, and the results are interpreted in relation to other measured quantities, such as the physical properties of the original samples and the density of the various fractions. It was found that only 7 to 8 per cent by weight of the solids was of colloidal dimensions and that neither of the samples contained montmorillonite but did contain illite. Considerable calcite was also found. These data should be useful to the geologist interested in the origin and history of sedimentary strata as well as to the petroleum engineer. Introduction The questions, What is good drilling mud? What constitutes bad drilling mud? are pertinent, because the proper use and control of drilling fluids has been a factor of great importance in the successful drilling and completion of oil wells since the days of Captain Lucas. Adequate control of the characteristics of drilling fluids has assumed greater significance comparatively recently because of the problems introduced by caving formations in deep wells, costly blowouts and impressive mud bills. Much is known about the solution of some of the problems but, despite extensive research directed toward a better understanding of the physical and chemical properties of clay suspensions, it is difficult to define precisely a drilling mud, and much more difficult to say what constitutes a good mud. It is generally believed that the smaller particles of a drilling mud greatly affect its physical properties. In fact, it is customary to blame the colloids in a mud for nearly everything that goes amiss, because colloidal properties have effects out of all usual proportion on viscosity, filtration rate and reaction to electrolytes. It is germane to know whether drilling muds possess colloids and if so, the quantity and kind. Source oF Samples Two drilling muds from the Hastings oil field, Brazoria County, Texas, were selected because it is generally agreed that in this oil field good natural muds made solely from formations penetrated by the drill can be used until the well is nearly ready for completion. Customary drilling procedure in this field is to spud in with water, set a protective string of pipe, drill to 2500 ft. and set the surface casing. Drilling is continued to 5500 ft. with no treatment of the drilling fluid other than addition of water to

Jan 1, 1943

By D. M. Buck

greatly restricted and every effort is being made to do away with it where possible, and to substitute a lead-base babbitt or a babbitt with 50 per cent,. tin. The amount of solder having the composition 50 lead, 50 tin, used by the Pennsylvania Lines East, during 1917, was approximately 100,000 lb., but there is reason to believe that a large portion of this can be replaced by a 60-lead, 40-tin solder with satisfactory results, and instructions have been issued to this effect. Inregard to the quantity of new tin used, it is not possible to give the amount, except approximately and from calculations based on the 1917 consumption of bearing metals by the Pennsylvania Lines East only, it is estimated that about 770,000 Ib. of new tin were required in a total of about 21,380,000 lb. of all kinds of bearing metals turned out by the foundry or purchased in the market. No change has been made in the specifications for bearing metals for some years, as the metals used have been satisfactory. A large proportion of the bearing metals are made up from old material re-melted and brought to standard composition by some addition of new metal, and every effort is being made to utilize old material to the best advantage and reduce the amount of new metal of all kinds purchased. For a number of years no tin has been used in the lining metal of either passenger or freight car journal-bearings, except such small amounts as come in from re-melting old linings. No change has been made in phosphor bronze used for rod bushings, as we should expect some trouble from bushings pounding out of shape if a phosphor bronze were used which contained less tin or more lead than the present specifications call for. In this, as well as in the case of all other bearing metals, we expect to use our utmost endeavors to economize and to substitute for tin wherever possible. The Tin-plate Industry D. M. Buck,* Pittsburg, Pa.—During the first 5 months of 1918, approximately 11,000,000 Ib. per month of pig tin were consumed in the United States. Solder, bearing metals, bronzes, etc, used about 5,500,000 lb.; collapsible tubes a little more than 250,000 lb.; tin-foil about 500,000 lb.; and the tin- and terne-plate industry somewhat less than 5,000,000 Ib. In an effort to reduce this consumption and thus conserve our tin supplies, several methods of procedure suggest themselves: 1. Salvage. The most careful and systematic collection and re-use of tin and tin-bearing materials is economically important, in that we thus

Jan 1, 1919

By D. W. Mitchell

While pure magnesium does not corrode rapidly the presence of even very small quantities of certain other metals accelerates corrosion remarkably. Because magnesium is such an electropositive metal (E° = +2.34 volts)' the presence of substances that permit galvanic activity is extremely undesirable. It is stated that as little as 0.017 pct of iron in magnesium causes a marked increase in the corrosion rate.2 Magnesium and its alloys are commonly melted in iron or steel pots; consequently the commercial metal has the opportunity to pick up iron if it has that tendency. Quantitative data on the solubility of iron in magnesium are of practical as well as of academic interest. Some magnesium alloy castings tend to have large grain size unless suitable treatment is given to the liquid metal just prior to casting. One method of grain refinement consists of "superheating" the metal just prior to casting. "Superhcating" is heating to a temperature 100 to 200°C above the casting temperature and holding for a short period of time. Superheated metal has a much finer grain than unsuperheated metal. A satisfactory explanation of this phenomenon has not been forthcoming. One hypothesis attributes the grain refinement in the superheated metal to precipitation of some phase that is mis-cible at the temperature of superheat but not miscible just below the casting temperature and which is thought to provide nucleating centers for crystallization. This phase, if the foregoing hypothesis is correct, would probably be a metal or an intermetal-lic compound. Of the metals likely to be found in magnesium alloys, iron is one of the most likely candidates for the role of grain refiner for iron occurs in small quantities in all commercial magnesium and magnesium alloys. A. Beck³ states that magnesium, in either the liquid or the solid state, cannot dissolve iron and that iron exists as a finely divided suspension which does not settle out because of its extreme fineness. Beck also presents a micrograph showing a large iron dendrite in magnesium but does not comment on the crystallization of iron from a solution supposed to contain none. It is doubtful that dendrite formation from suspended iron -would be possible. This suspension theory is the basis of patents4 covering the removal of iron from magnesium by allowing the iron particles to act as nuclei for the formation of primary magnesium crystals which can be separated by segregation. Also covered by patents is the removal of iron by the addition of another metal to form an intermetallic compound with the iron which, because of its increased particle size, is able to settle out of the molten metal. Here, too, quantitative information on the extent of iron solubility in liquid magnesium is of more than theoretical interest. M. Hansen,5 in his critical collection of the data on binary alloys, states that iron is not soluble in liquid magnesium. W. R. D. Jones% ho studied the physical properties of low iron magnesium alloys observed a 57°

Jan 1, 1949

By F. C. Dyer, H. E. T. Haultain

There has been much written on ball-mills, but no small amount of the literature is simply the expression of individual opinion without sufficient data. This is no doubt due to the complexity and obscurity of the phenomena involved. The outstanding paper is by E. W. Davis,I superintendent, School of Mines Experiment Station, University of Minnesota, which is based on a large amount of data from careful experiments with full-size apparatus, together with some mathematical philosophy. The entire philosophy is summed up in the equations given; but the present writers question the foundation upon which this philosophy is based. Encouraged by the work of Davis, the authors of this paper continued work they had been doing along this line. At first, photographs were taken of the ends of rods in a small laboratory rod mill. The mill was tilted slightly toward the feed end and the discharge end was removed. The rods remained in the mill long enough to permit good observation and good photography. Later, a mill 24 in. inside the stepped lining was constructed. It consisted of two sheets of plate glass, 1/2 in. apart, set in a cast-iron ring. It was driven by a variable speed motor and was connected to an accurate speedometer (magneto and voltmeter type). In place of balls or rods, cast brass disks were used. These were 3/8 in. thick and varied in diameter from 2 in. down to 3/4 in. Four small projections on each side prevented the disks sticking to the glass when water was used; sometimes steel balls % in. in diameter were added to the load of disks. There was also constructed a 6-in. mill with corrugated linoleum lining and containing a dry load of various sizes of steel balls. The mills were so connected to the motor that the small mill made two revolutions to one of the large mill. Many runs were made with a great variety of materials, including crushed marble, seeds of many kinds, and many mixtures (some wet and

Jan 1, 1923

By F. C. Dyer, H. E. T. Haultain

There has been much written on ball-mills, but no small amount of the literature is simply the expression of individual opinion without sufficient data. This is no doubt due to the complexity and obscurity of the phenomena involved. The outstanding paper is by E. W. Davis,I superintendent, School of Mines Experiment Station, University of Minnesota, which is based on a large amount of data from careful experiments with full-size apparatus, together with some mathematical philosophy. The entire philosophy is summed up in the equations given; but the present writers question the foundation upon which this philosophy is based. Encouraged by the work of Davis, the authors of this paper continued work they had been doing along this line. At first, photographs were taken of the ends of rods in a small laboratory rod mill. The mill was tilted slightly toward the feed end and the discharge end was removed. The rods remained in the mill long enough to permit good observation and good photography. Later, a mill 24 in. inside the stepped lining was constructed. It consisted of two sheets of plate glass, 1/2 in. apart, set in a cast-iron ring. It was driven by a variable speed motor and was connected to an accurate speedometer (magneto and voltmeter type). In place of balls or rods, cast brass disks were used. These were 3/8 in. thick and varied in diameter from 2 in. down to 3/4 in. Four small projections on each side prevented the disks sticking to the glass when water was used; sometimes steel balls % in. in diameter were added to the load of disks. There was also constructed a 6-in. mill with corrugated linoleum lining and containing a dry load of various sizes of steel balls. The mills were so connected to the motor that the small mill made two revolutions to one of the large mill. Many runs were made with a great variety of materials, including crushed marble, seeds of many kinds, and many mixtures (some wet and

Jan 1, 1923

By R. B. Haagensen, E. Martinez, V. Kudryk

The sample under investigation contained approximately 16% BaSO, and was 80% -325 mesh. Established methods for floating barite did not produce concentrates of satisfactory grade or barite recovery because of low barite content and the presence of 6% calcite in the feed. By using a new long-chain sulfosuccinamate collector in combination with relatively high concentrations of sodium silicate, a barite concentrate was produced that would be acceptable as an oil-drilling mud using a simple rougher-cleaner circuit. No desliming of the fine-ground feed was necessary. Barite recovery was over 80% and the concentrate produced had a specific gravity higher than 4.3. During the course of the investigation, a procedure was developed to obtain semiquantitative determinations of barite, calcite, quartz, and feldspar in test samples using an infrared spectrophotometer. Samples were also analyzed in a thermobalance for determination of the calcite content. The use of these instruments made it possible to obtain quick mineralogical assays and proved to be of invaluable assistance in guiding the flotation testing.

Jan 1, 1976

By W. M. Dressel, A. Visnapuu

The Bureau of Mines, U.S. Department of the Interior, has upgraded high-iron domestic chromite concentrate to high-chromium concentrate by a laboratory carbonyl process. The chromite concentrate product has a chromium-to-iron ratio in excess of 3:l compared with the starting concentrate ratio of 1.6:1. The high-iron chromite was first reduced to convert the iron oxides to the metal, and then treated with carbon monoxide at elevated pressures and low temperatures to convert the metallic iron fraction to iron pentacarbonyl. Carbonylation was accelerated by the addition of hydrogen sulfide in small quantities. A constant flow of carbon monoxide swept the iron pentacarbonyl formed in the reactor out through a pressure-reducing valve. The mixture of carbon monoxide and iron pentacarbonyl at atmospheric pressure was then passed through a heated section to decompose the iron pentacarbonyl to carbon monoxide and iron, whereupon the latter plated out on the heated surface. Carbon monoxide pressure, temperature, and promoter trends for enhanced carbonylation are presented.

Jan 1, 1984

By Jack C. Bokros, Philip C. Rosenthal

DEVELOPMENT of the autoradiographic method in metallurgical research has been directed mainly toward gaining higher resolution, i.e., toward being able to locate segregation of a radioactive isotope on a finer scale. In the investigation reported, the liquid emulsion autoradiographic technique' used in the biological science was adapted to the autoradiography of metals. The distribution of carbon-14 in pure iron after various treatments was studied using this technique. Amorphous carbon uniformly labelled with carbon-14 at a specific activity of 6.95 microcuries per millimole was obtained from Tracerlab Inc. Carbon-14 emits P particles having a maximum energy of 157 kev and an average energy of about 50 kev. These ßs have a maximum range of about 30 mg per cm' and a half-thickness of about 3 mg per cm2. The iron used was spectroscopically pure electrolytic iron prepared by the Oak Ridge National Laboratory. Unhardened nuclear track emulsion, type NTB, was kindly supplied by the Eastman Kodak Co. This emulsion contains approximately 80 pct Ag halide,

Jan 1, 1957

By C. O. Ensign

Results of the application of geo1ogic knowledge to grade control have been remarkable. Grade reduction from dilution has been diminished from greater than 9% at the time of the program's beginning to about 2% at present. This has resulted in an increase of about 1.8 lb of copper per ton of ore mined and has made a substantial contribution to earnings at White Pine during the past two years. Even more improvement is expected in the future. The White Pine orebody, situated in the southwestern portion of the Keweenaw peninsula of upper Michigan, is a gently dipping stratiform or bedded deposit. Copper distribution is stratigraphi-cally controlled with higher values being confined to specific beds in the ore column. Room-and-pillar mining is practiced. Mining technique and geologic characteristics present a special array of problems in controlling the grade of ore. A routine program of grade control was started in the White Pine mine in August 1961. The program is based upon development and application of geologic knowledge to assist mine operating personnel to increase the grade of ore, primarily by accurate stratigraphic control and selection of areas for development on the basis of grade distribution trends. Geologists work closely with mine supervisors to offer the necessary geologic guidance. STRATIGRAPHIC POSITION OF COPPER The important rock series in the White Pine area is comprised of three formations of late Precambrian age. In descending order they are the Freda sandstone, Nonesuch shale, and Copper Harbor conglomerate. The Nonesuch shale is about 600 ft thick. Economic copper concentration occurs only in the lowermost 20 to 25 ft of the formation; however, within a restricted area along the southwest side of the mine the uppermost 1 to 7 ft of the Copper Harbor conglomerate (lower sandstone) contain sufficient quantities of copper to be included in the ore column. The ore consists primarily of chalcocite with subordinate native copper disseminated in shales, siltstones, and sandstones. MINE BOUNDARIES AND STRUCTURE The mine area is bounded on the west by the sub-outcrop of basal Nonesuch at bed rock surface and on the southwest by the White Pine fault (Fig. 1). The south and southeast limit of the orebody is reasonably well delineated by thinning or pinch-out of favorable host beds. Northern, northeastern, and eastern limits have not been established. The White Pine fault is actually a wide zone of shearing which strikes approximately N 40° W. It is downthrown on the southwest side and dips steeply to the northeast. Maximum vertical displacement is about 1500 ft.

Jan 1, 1964

Jan 1, 1946

By Charles H. MacDowell

Up to 1909 the American public had little knowledge of, or interest in, potash. Some remembered that it had to do with soft soap and sore throat,, but further they knew not. In 1909-10, the German-American potash war, and the publicity attending hostilities, brought home to America the knowledge that potash was an important article of commerce; that Germany monopolized its production and distribution, and exercised all the prerogatives attending complete control. The present war, with its transportation embargo, has again directed attention to Germany's strength as a potash producer and her present unfortunate situation as a distributor. As a consequence, the search for potash takes on new life and it again becomes a subject of general interest. My first knowledge of potash came from a study of the German potash exhibit at the World's Fair in 1893. This investigation led to the recommendation that Armour & Co. engage in the manufacture of commercial fertilizers and the fertilizer branch was organized early in 1894. From then to now " potash " has been a live subject. Two and eight-tenths per cent. of the earth's crust consists of potassium oxide. It is an important constituent of feldspar, granite, and other igneous rocks. Potash is valuable commercially in a water-soluble form. In igneous rocks it is locked in so tight that it is of little value and no utilization in a commercial way has been made of these insoluble forms. Potash in water-soluble form is found in large deposits in Germany; in smaller deposits in Austria and Spain; and in brines in some of our Western arid basins. The deposits in Germany, Austria, and Spain are concentrations from sea waters containing potash derived from the decomposition of potash-bearing rocks. It has been found that the amount of potash remaining in decomposed rocks is not the same as that in the original rock. For instance, granite containing originally 5.58 per cent. potash contained only 1.49 per cent, in the decomposed rock. Syenite containing 6 per cent. in the original

Jan 1, 1915

By G. Y. Chin, M. T. Dolan, W. L. Mammel

The least work analysis of constrained deformation, first proposed by Taylor and recently modified by Chin, Hosford, and Mendorf to include twinning, has been applied to the problem of axisynmetric flow. Calculations were made, for the case of (111}(110) slip and {111}(112) twinning applicable to fcc deformation. The solutions were obtained by linear programming techniques and with the aid of computer methods. The results show that in axisymnzetric tension the onset of twinning tends to decrease the plastic strength anisotropy as compared with the case of defortnation by slip alone. In compression, however, the strength anisotropy is increased as a result of twinning. The [100] and 11111 orientations and their vicinity are unfavorable for twinning in tension and compression, respecticely. With slight modifications, the present results may be applied to bcc metals deform ing by {110}(111j slip and (112} (111) twinning. Implications of present results to wire texture development of low stacking fault energy fcc materials arc discussed. PREVIOUSLY we' have applied linear programming techniques to obtain solutions to Taylor's least work analysis2 of constrained deformation of single crystals undergoing axisymmetric flow, such as occurs in an axially loaded polycrystalline aggregate. These solutions yielded values of the parameter M = o/.r = Y/w which relates the external stress-strain (u-c) curve to the shear stress-shear strain (7-y) curve for the crystal. The value of M is dependent on crystal orientation and hence enters significantly in texture strengthening considerations.3'4 Recently the Taylor hypothesis was modified by Chin, Hosford, and Mendorf' to include mechanical twinning. The latter has now been applied to the problem of axisymmetric flow and the results are reported in this paper. Calculations have been made for {111 )( 110) slip and {111 )(112) twinning applicable to fcc crystals. With minor changes in the indices of the slip and twin systems, the present results are also applicable to bcc crystals which slip on (110) (111) and twin on {112)(111) systems.

Jan 1, 1970

By J. W. Spretnak, G. Sachs

The: iron-rich iron-nickel alloys have attracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are the base of many alloys with various outstanding properties. The iron-nickel alloys, therefore, have been investigated extensively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,l and will be discussed in some detail in the sections of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to 10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis," which is not dependent upon the rate of cooling and persists even with very slow rates of cooling.3 Honda4 and Merica4 have therefore resigned themselves to proposing a diagram (Fig. I) for practical use, illustrating the structural relations under commercial conditions instead of attempting to establish the true equilibrium diagram. Marsh is less pessimistic and suggests an equilibrium diagram (Fig. 2) which conforms approximately to the facts known about this system. Recent X-ray investigations by Owen-Sully5 and Bradley-Gold-schmidt6 on powdered alloys indicate that the previous work on the iron-nickel system yielded very incomplete results. These investigators agree (Figs. 3 and ,+) that alloys in the powdered form containing more than 8 per cent and up to about 35 per cent Ni decompose into a stable heterogeneous mix-

Jan 1, 1941

By G. Sachs, J. W. Spretnak

The: iron-rich iron-nickel alloys have attracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are the base of many alloys with various outstanding properties. The iron-nickel alloys, therefore, have been investigated extensively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,l and will be discussed in some detail in the sections of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to 10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis," which is not dependent upon the rate of cooling and persists even with very slow rates of cooling.3 Honda4 and Merica4 have therefore resigned themselves to proposing a diagram (Fig. I) for practical use, illustrating the structural relations under commercial conditions instead of attempting to establish the true equilibrium diagram. Marsh is less pessimistic and suggests an equilibrium diagram (Fig. 2) which conforms approximately to the facts known about this system. Recent X-ray investigations by Owen-Sully5 and Bradley-Gold-schmidt6 on powdered alloys indicate that the previous work on the iron-nickel system yielded very incomplete results. These investigators agree (Figs. 3 and ,+) that alloys in the powdered form containing more than 8 per cent and up to about 35 per cent Ni decompose into a stable heterogeneous mix-

Jan 1, 1941

By G. R. Speich

The distribution of carbon and the type of substructure in iron-carbon martensites containing 0.02 to 0.57pct C has been studied in the as-quenched condition and after tempering at 25" to 700°C by using electrical resistivity, internal friction, hardness, and light and electron microscope techniques. in marten-sites containing less than 0.2 pct C, almost 90 pct of the carbon segregates to dislocations and to lath boundaries during quenching; in martensites containing greater than 0.20 pct C, appreciable amounts of carbon enter normal interstitial positions located far from defects. Tempering martensites with carbon contents below 0.20 pct at temperatures below 150°C results in additional carbon segregation to dislocations and to lath boundaries but no carbide precipitation whereas -carbide precipitation occurs in martensites with carbon contents exceeding 0.2 pct. Above 150°C, a rod-shaped carbide (either Fe3C or Hagg) is precipitated in all cases. At 400°C, spheroidal Fe3C precipitates at lath boundaries and at former aus-tenite grain boundaries. At 400" to 600"C, recovery of the martensite defect structure occurs. At 600" to 700°C, recrystallization of the martensite and Ost-waW ripening of the Fe3C occur. The effects of the carbon segregation that occurs during quenching and the subsequent substructural changes that occur during tempering on martensite tetragonality, hardness, and precipitation behavior are discussed. A mathematical analysis of carbon segregation during quenching is presented. RECENT studies of the strength of low-carbon martensitel-4 emphasize the importance of carbon segregation to the martensite lath boundaries and to the dislocations contained between them during quenching. Unfortunately, very few studies of the tempering of low-carbon martensites have been conducted, so the exact nature of this segregation is poorly understood. In fact, most early tempering studies5,6 were restricted to carbon contents greater than 0.20 pct. Moreover, these studies did not determine the amount of carbon segregated to the martensite substructure during quenching so that the initial state of the martensite was not established. Aborn7 studied the precipitation of carbide in low-carbon martensite during quenching but did not establish whether carbon segregation occurs prior to carbide precipitation, nor did he study the subsequent tempering sequence in detail. In the present work we have used electrical resistance and internal friction measurements, supplemented by electron transmission microscopy to establish the carbon distribution in as-quenched specimens. Specimens thin enough to avoid carbide precipitation (but not carbon segregation) were employed. The redistribution of carbon on subsequent tempering below 250°C was followed by measurements of elec- trical resistance. Additional studies were made on specimens tempered at 250" to 700°C to elucidate the overall tempering behavior of low-carbon martensites, including the formation of cementite and recrystalli-zation of the martensite. EXPERIMENTAL PROCEDURE Eight iron-carbon alloys with 0.026, 0.057, 0.097, 0.18, 0.20, 0.29, 0.39, and 0.57 wt pct C were prepared as 8-lb ingots by vacuum melting. Typical impurities in wt ppm were 40 Si, 20 Mn, 30 S, 10 P, and 10 N. These alloys were hot rolled to 3 in. plate at 1095°C) (2000°F). The hot-rolled plates were surface ground to remove scale and the decarburized layer, then cold rolled to 0.010 in. sheet. Specimens cut from the sheet were austenitized for 30 min at 1000°C (1830°F) in a vacuum tube furnace in which the pressure did not exceed 2 x 10-3 torr. Chemical analysis of specimens after austenitization indicated no decarburization at this pressure. Immediately before quenching, the furnace was filled with prepurified helium. The specimen was then pushed rapidly through an aluminum foil gasket, which sealed the bottom of the furnace, into an iced-brine bath (10 pct NaC1, 2 pct NaOH). The quenching rate at the M, temperature is about 104'c per sec for 0.010 in thick specimens, as calculated from Newton's law of heat flow2 using a heat transfer coefficient of 25 ft-'. This quenching rate is sufficiently high so that all the alloys transformed completely to martensite throughout the entire 0.010 in thickness and no carbide precipitation occurred in the martensite. All specimens were immediately transferred to liquid nitrogen after quenching and stored there until needed. Tempering below 250°C (480°F) was done in silicone oil baths thermostatically controlled to *;"C. Tempering above 250°C was done in circulating air furnaces or lead pots with the specimens contained in evacuated silica capsules. Electrical resistance was determined by measurement of the potential drop across both a standard resistance and the specimen, connected in series. All resistance measurements were made in liquid nitrogen (77K, -196°C) to minimize thermal scattering of electrons and thus maximize the contribution of impurity scattering to the resistance. Specimen dimensions were 5.10 by 0.19 by 0.025 cm. Although the precision in the electrical resistance measurements was +0.1 pct, the electrical resistivities could only be measured with an accuracy of +5 pct because of uncertainty in the specimen dimensions. Internal friction measurements were performed in an inverted pendulum apparatus at vibration frequencies of either 1.9 or 66 Hz. The specimen dimensions were 5.10 by 0.375 by 0.025 cm. Hardness measurements were made with a Leitz-Wetzlar microhardness machine with loads of 100 g. Specimens were examined by light microscopy after etching in 2 pct Nital and by electron transmission microscopy after preparation of thin sections by electrolytic thinning in a chromic-acetic acid solution.

Jan 1, 1970

By F. C. Sturges

For some time mining engineers have been interested in the possibility of using small diameter shafts, sunk by core drilling, as aids to ventilation and as emergency escapeways. The possibilities are interesting to contemplate, but new methods involve unknowns, and interest tends to remain passive until these unknowns are, solved. Recently we have completed two 36-in. diam core drilled shafts, and wish to make the data on these available to the industry. Both shafts were drilled for the McLain Fire Brick Co., one at its Buckeye mine and the other at its Colonial mine. Both mines are in the fireclay underlying the Lower Kittanning coal. Both mines have been in operation for a number of years and have required expensive maintenance work on return airways. It was decided that considerable savings could be effected by short-circuiting the air to the surface through small shafts. It was also realized that these holes, located near the present workings, would be of added value as emergency escapeways. Originally, 48-in. diam shafts were considered, but actual computations showed 36-in. diam shafts were more than ample at both mines. The shaft at the Buckeye mine is 240 ft deep, and that at the Colonial mine 258 ft deep. Both holes were started in the lower part of the Conemaugh formation and penetrated Conemaugh and Allegheny strata. The holes were started through the unconsolidated materials overlying bedrock by constructing a concrete collar with a wall thickness of 8 in. Then the shafts were drilled by the shot-core drill method. An annular groove was cut in the rock by the abrading action of chilled steel shot run under the shoe of the core barrel. The drilling was done in stages, the core barrel drilling the groove for a certain distance depending on conditions encountered, and then the cores broken off and taken out in sections. The core barrel had a 36-in. o.d. and the finished diameter of the shaft measured almost 37 in. The major questions that could not be answered until the completion of the first shaft were, (I) how much ground water would be encountered, how would it hinder the drilling, and how difficult would it be to seal off, and, (2) how would the walls of the hole stand up. The holes of course could .be cased or lined, but that is considerable added expense in any shaft.

Jan 1, 1949

IN welcoming the attending members of the Ameri-can Zinc Institute's Ninth Annual Meeting to St. Louis on April 18, the president of the Chamber of Commerce stressed the notable progress that had been made during nine years, marked by many price de-pressions and internal dissensions, while controversies between miners and smeltermen threatened to wreck the organization, prices dropped, and consumption grew languid for want of organized publicity and research. The reports and recommendations of Percy B. Butler, chairman of the Adjustment Committee, and F. C. Wallower, chairman of the Galvanizing Committee, might well be adopted as the institute's objectives. In reply to the speeches of welcome to St. Louis, Arthur Thacher reminded the delegates that the cor-ner stone of progress in the mineral industries was laid by the formation of the American Institute of Mining Engineers in Wilkes-Barre, Pa., in 1871, and the dedication of that organization to the exchange of ideas and methods of the winning of metals and non-metals from their crude state. The activities of the American Zinc Institute constitute, he said, a valuable phase of that work. Mr. Thacher forecast the treat-ment of 1 per cent zinc ore. After the reading of the report of the board of directors, in which Scott Turner and Louis Boschern were named as honorary members of the institute, a survey of world zinc conditions by A. J. M. Sharpe of London was presented. He held pres-ent conditions in China responsible for much of the present depression in zinc. World stocks on, April 1, 1927, were estimated as 52,900 metric tons. Adolph Boldt's paper on "Solidarity in Industry" was followed by a survey of the Tri-State district by Otto Ruhl, who emphasized the importance to the dis-trict of the organization of the Tri-State section of the A.I.M.E., which already has 135 members and asso¬ciates. He also mentioned .that flotation in the Tri¬State field is adding 1500 tons of concentrate to the weekly production. "Mining Economics" was the subject of Julian D. Conover, secretary of the Tri-State Zinc and Lead Ore Producers Association. He gave a detailed report on the costs of mining and milling in the district.

Jan 5, 1927

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments, and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table 1 are reported the compositions of the core and cladding alloy for the material used for the experiments. [ ] In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion.1-7 Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R301 varies with the gauge, as shown in Table 2, several gauges were investigated. [ ] MATERIAL AND PROCEDURE The material used was sheet of the following gauges: 0.025, 0.040, 0.064, 0.102, 0.170. Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: 910°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After 200 min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1945