Search Documents

By H. C. Howarth

This paper gives observations on ground movement and subsidence resulting from pillar drawing in the Lick Run section of Montour No. 10 mine of the Pittsburgh Coal Co. adjacent to solid coal owned by the U. S. Bureau of Mines at its Experimental mine in Snowden Township, Allegheny County, Pennsylvania. The investigation was planned by George S. Rice, chief mining engineer of the Bureau, who arranged the necessary cooperation with Dr. L. E. Young, vice president of the Pittsburgh Coal Co. Engineers of that company placed permanent monuments on the surface to establish the boundaries of the coal owned by the Bureau and to furnish fixed points to which all levels were referred. Engineers of the Experimental mine staff then covered the ground under observation with a checkerwork of monuments made of oak pegs set into the ground at 50-ft. intervals in two directions at right angles to each other. The level of these pegs was determined first from Dec. 16 to 30, 1929; again from May 25 to June 5, 1930, and finally from July 7 to 15, 1931. Observations were then discontinued because work had been stopped temporarily in this part on Montour 10 mine. General Conditions Fig. 1 is a plan of the part of the area under observation with which this paper deals. The mine is developed on a room and pillar system known locally as half advancing and half retreating. As Nos. 35 and 36 butt entries were advanced, rooms were driven from No. 36 and drawing of the room pillars followed their completion. When the entries reached the boundary, rooms were started from No. 35 butt beginning at that point, and all remaining pillars were drawn as rapidly as possible. The rib lines of Jan. 9 and June 13, 1930, were surveyed a week to 10 days after the first and second sets of levels were run, and there was some advance in that period. The rib line of July 15, 1931, agrees in time

Jan 1, 1934

RAYMOND M. Howe (author's reply to discussion*).-Dr. Unger states that magnesite will hardly supersede dolomite in fettling after a heat; that it is hard to believe a slag composed of oxide of iron containing about 6 per cent. of phosphorus is the active corroding, agent in a boil in a furnace; and that boiling cannot be said to be the result of the chemical action of a high-phosphorus slag on a basic bottom. These are well-established facts that no one would venture to question. The authors were misinterpreted in the statement that "in the summary, it is claimed that magnesite low in lime, or of greatest purity, ranks first in resistance to slaking," etc. On the contrary, the position has been taken throughout that while a low lime content is advantageous, the presence of several per cent. of iron oxide (an impurity), is necessary in order to confer the proper bonding and sintering properties in dead-burned grain magnesite to be used for furnace hearths. We cannot subscribe to the view that pure magnesia is no better fitted for a refractory than pure lime,' nor that the pure natural varieties of magnesite; such as Grecian or Washington, must necessarily be burned with silica and oxide of iron to produce a satisfactory material. On a small scale, pure magnesia has been satisfactorily used as a refractory in the form of crucibles. In the production of dead-burned grain magnesite from the Grecian or Washington mineral, iron oxide is added but the addition of silica is neither customary nor desirable. It is possible to manufacture brick of good quality from both the Grecian and the Washington material without adding either silica or iron oxide, providing they are burned at a sufficiently high temperature. This is regularly done on a commercial scale both in America and abroad when brick of. exceptionally high refractoriness or special purity are desired. The following analysis is of an English brick of Grecian magnesite which is extremely low in all impurities.1

Jan 6, 1919

By R. S. Hutton

WHEN I had the honor of receiving an invitation to give the-Institute of Metals Lecture, it occurred to me that it might be of interest to review the advances which have been made in refractories, considering how important these materials of construction are in the carrying out of many metallurgical operations and what a large factor they represent in our costs of production. Frankly, I can claim no recent contact with the refractories industry and what little work I myself have been concerned with has been rather unorthodox in character. However, perhaps in consequence of this, I can approach the review without bias and include some suggestions which may prove stimulating or provocative to some of you, who have a more intimate knowledge of refractories and their uses than I Possess. It is neither possible nor necessary for me to survey the progress of industrial refractories, for this has been so thoroughly undertaken by others1-7 in recent publications. Perhaps the best way to get a broad picture of this progress is to compare the Faraday Society Symposium on Refractory Materials 20 years ago8, containing a report on one of the first attempts at standardized testing, with the American Society for Testing Materials Committee Report of February 1935. Suffice it to say, lest my provocative remarks be misunderstood, that I do appreciate that great advances have been made, particularly by companies that have established their own research laboratories and by universities and cooperative research institutes working for the common weal of groups of manufacturers or for national and international progress. The scientific study of the constitution diagrams of binary and ternary refractory oxides, which American workers have been foremost in under-taking, ? led by the work of the Geophysical Laboratory at Washington, has laid a firm foundation for the whole subject. It should be remem-bered, however, that to a much greater degree than with the constitution of metal alloys, the equilibrium conditions are so sluggishly arrived at

Jan 1, 1937

E. A. Peretti (University of Notre Dame, Notre Dame, Ind.)—Mr. Deitz and Professor Halpern are to be congratulated on a fine piece of work which adds to our knowledge of precious metal—cyanide-solution reactions. I should like to offer the following comments: The authors state, "the rate plots were always linear, indicating a zero order reaction rate." This appears to conflict with the data of Fig. 6 which clearly show the rate to vary with the NaCN concentration. It seems to me that the rate curves are linear because of the experimental setup. The volume of solution is so large that over a three-hour period the change in NaCN concentration is very small. A rough calculation for the experiments of Table I where the initial NaCN strength was 0.0096 mol per liter show a change of NaCN concentration of about 0.0009 mol per liter at the end of three hours. In short, over the period of time that the experiment was in progress, the NaCN strength was practically constant; hence the rate of dissolution remained practically constant. Eq. 10, as written, specifies that 1 mol of H202 and 2 mol of hydroxyl ion are formed when 2 mol of silver react. Is this true? The effect of H,O2 on the rate was made in solutions having an oxygen pressure of 4.8 atm. Were any tests made in solutions containing hydrogen peroxide, but no oxygen? G. M. Willis (University of Melbourne, Melbourne, Australia)—The authors have shown that, under their experimental conditions of high O2 concentrations, the rate of solution of silver in aqueous cyanide solutions is controlled by diffusion of O2 or CN- to the metal surface. With diffusion control, it is generally not possible to obtain further information about the mechanism of a process.

Jan 1, 1955

By George J. Young

The recurrence of mine-fires in Nevada during the past decade is not only a matter of interest, but also one of considerable concern to engineers and mine-managers. The more important fires may be enumerated as follows: Forman Shaft fire, Gold Hill, April 21, 1903; shaft-house, machinery, and shaft destroyed; loss estimated at $50,000; cause unknown. Union Shaft fire, Virginia City, July 14, 1904; shaft-house, machinery,and shaft in part destroyed; loss estimated at $100,-000; cause of fire stated as the careless throwing of a match in the rope-house. Sutro Tunnel fire, Virginia City, Jan. 27, 1909; 700 ft. of tunnel-timbering destroyed, and direct damage of $10,000; cause " probably electric wires." Belcher Shaft fire, Gold Hill, Aug. 9, 1910; shaft-house destroyed, machinery ruined, and upper part of shaft damaged; damage, $25,000; no cause given. Belmont Mine fire, Tonopah, Feb. 23, 1911; fire started ill winze; 17 men killed. Giroux Mine fire, Kimberly, Aug. 23, 1911; fire originated in shaft-station from unknown cause; 7 men killed, and $34,-521 damage caused. (Note 1.—On June 11, 1912, some time after the present paper was written, a fire broke out in the pump-room on the 2475 station of the Ward shaft, Virginia City. This fire was caused by the short-circuiting and exploding of the starting-switch on No. 5 pump. The oil in the switch was scattered about and set fire to the timbers and lagging of the pump-room. The pump-man in charge notified the surface, and the electric current was shut off. A hose was then turned on the fire, but the dense smoke drove the attendant out. Inspection by the electrician and the shaft-foreman, equipped with oxygen-

Jan 1, 1913

By R. C. Thompson

THE lead-zinc mill of Phelps Dodge Corporation, Copper Queen Branch, Mines Division, Bisbee, Arizona, is about 3 miles from the main hoisting shafts of the Junction and Campbell mines at Lowell. All the ore treated in the mill is obtained from these two mines. The mill was designed for an all-flotation treatment of 450 tons of lead-zinc ore per day, and has been operated at that capacity since the start of milling operations on Nov. 17, 1945. An expansion program is underway whereby the mill capacity will be doubled, but this article describes only the original program and presents results of the 45o-ton operation. GENERAL DESCRIPTION The milling plant consists of an ore-receiving bin and three steel-constructed buildings housing, respectively, the primary crushing equipment, the secondary crushing equipment, and the ore-storage bins, grinding, flotation, and filtering equipment. The mill site is the one that was used for a previous copper-concentrating plant, which was operated over a period of years and then dismantled. There remained from this operation some milling equipment, a reservoir for mill-water supply, railroad tracks, tailings-disposal ponds, and a steel-constructed building, all of which were incorporated in the design of the present lead-zinc mill. The location plan of the plant layout is shown in Fig I. The flowsheet of the mill is based on the conventional scheme for lead-zinc treatment, however, several innovations were made necessary in order to utilize the existing building. Placing of equipment also was governed by the design of the building; thus making the mill unique in many respects. The following brief description of the mill building as adapted to the flowsheet points out the compactness of the installation and some of its unusual features. The first floor (Fig 2) houses the grinding equipment, with connecting conveyors for ore feeding, also an air compressor, two vacuum pumps, bins for lead and zinc concentrate storage with individual conveying systems for loading the two kinds of concentrates. Filtering of concentrates is done on the second floor, the concentrates discharging directly into the concentrate-storage bins. On this floor are the lead and zinc filters, two diaphragm pumps, sample-filtering equipment, sample-preparation room and a change room for the mill employees. The flotation machines are on the third floor, at elevations allowing a gravity flow of the lead and zinc concentrates to the thickeners. The annex to the building contains a freight elevator and provides space for all reagent mixing and feeding, also storage of reagents and grinding balls. All the water used for milling purposes is pumped from the Junction mine and

Jan 1, 1947

By Nicholas J. Grant, Robert F. Wilde

TAYLOR and Floyd's"" work in establishing phase diagrams based on the elements Ni-Cr-Ti-A1 has led to an understanding of the precipitation hardening mechanism in alloys based on these elements. Nordheim and Grant4 concluded that in simple alloys, and where the aluminum to titanium atomic ratio was such that less than three out of five aluminum atoms were replaced by titanium, the precipitate on aging is the face-centered-cubic Ni 3A 1 phase, called They further found that increasing amounts of hexagonal ? phase, Ni3Ti, precipitated from these alloys when the titanium content exceeded the solid solubility of both matrix and Ni3A1. For alloys of Ni-Cr-Ti-Al, in which the titanium and aluminum contents each ranged from 0 to 4 wt pct, the titanium-rich was superior for strengthening to either pure ?' or 7. It was also noted that the combined titanium plus aluminum content (atomic pct) was a direct measure of the high temperature strength and overaging temperatures for these alloys.4 The present investigation was undertaken to extend existing data on precipitation hardening in the more complex commercial alloys containing higher titanium plus aluminum, and with significant quantities of cobalt, molybdenum, and carbon. Experimental Procedure Reforging of As-Received Bar Stock—The alloys were received as ground, forged bar stock. Chemical analyses and the as-received bar diameters are shown in Table I along with the ASTM grain size after the various treatments. All stock except the Waspaloy was reforged to % in. diam to gain material and to facilitate machining of stress-rupture specimens. Forging was carried out at 2100°F, and discontinued when the bar temperature fell to 1800°F. Heat Treatments—For experixental simplicity it was desirable to heat treat all of the alloys at, the

Jan 1, 1958

By Walter L. Crow

MUCH has been published on highly technical phases of grinding. Very little has been written on how a mill man can improve his operations by determining the optimum size assortment of grinding balls that should be added as a makeup charge. This ball rationing is not to be confused with the ball ration used as an initial charge when the mill is started up. Ball rationing is considered for one or more of the following purposes: 1) to increase throughput of the mill, 2) to reduce the power required per ton of ore ground to the desired size, 3) to reduce steel consumption per ton of ore ground, 4) to improve product size, and 5) to lower retention time of ore in the mill.

Jan 7, 1957

By Ralph W. Smith

Development of the lime industry in Ste. Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there arc today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. Geology The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft, of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaCo3; 0.35 SiO2; 0.3 R2O3; 0.35 MgCO3; 0.3 SO3. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 1/2°. Thus the outcrops of the various sedimentaries run approximately north and south. A line running west from Ste. Genevievc crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 1/2° the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile wide. The early quarry and lime developments at Ste. Genevieve mere in this easily obtained surface rock of the Spergen outcrop.

Jan 1, 1938

By Ralph W. Smith

Development of the lime industry in Ste. Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there arc today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. Geology The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft, of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaCo3; 0.35 SiO2; 0.3 R2O3; 0.35 MgCO3; 0.3 SO3. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 1/2°. Thus the outcrops of the various sedimentaries run approximately north and south. A line running west from Ste. Genevievc crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 1/2° the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile wide. The early quarry and lime developments at Ste. Genevieve mere in this easily obtained surface rock of the Spergen outcrop.

Jan 1, 1938

By K. M. Myles

The vapor pressure of palladium over a series of Rlz-Pd alloys has been measured by the torsion-effusion method. The thermodynamic properties of the alloy system at 1575=K have been calculated from the vapor pressure data. The activities and the free energies of formation exhibit large positive deviations from ideal behavior. The enthalpies of formation are endother-mic. The entropies of formation are positive and larger than the ideal entropy of mixing. All of the thermodynamic properties suggest that a strong tendency toward phase separation exists in the solid solutions. The possible origin of the phase instability and the various factors that influence the thermodynamic properties are discussed. RECENT studies of the thermodynamic properties of alloys of palladium with nontransition elements have indicated that a significant contribution to the enthalpy of formation is related to the redistribution of the conduction electrons upon alloy formation.'-' The present work was undertaken to ascertain the importance of this contribution in Pd/transition-metal alloys. The Rh-Pd system was chosen for this investigation for several reasons: 1) The thermodynamics of the system were unknown. 2) Rhodium and palladium are completely soluble at high temperatures; below 1118OK the solid solution becomes immiscible.', 3) The difference in magnitude between the vapor pressures of rhodium and palladium permitted the use of an existing effusion apparatus. 4) Additional information was known about the alloy system that would facilitate the interpretation of the thermodynamic results. EXPERIMENTAL PROCEDURE The thermodynamic properties of the Rh-Pd alloy system were calculated from the vapor pressure of palladium over solid palladium and over several solid Rh-Pd alloys. The vapor pressure was measured by means of the torsion-effusion apparatus that has been described previously. In this method, an effusion cell is suspended from a tungsten filament inside a high-temperature furnace. Two orifices are located eccentrically such that the effusion of the vapor creates a rotational torque in the filament. The angle of rotation is directly related to the total vapor pressure within the cell. As the vapor pressures of rhodium and palladium are approximately five orders of magnitude apart," the total vapor pressure was considered to be effectively equal to the equilibrium vapor pressure of palladium. The effusion cells were made from high-purity alumina since auxiliary experiments indicated that essentially no reaction occurs between alumina and solid Rh-Pd alloys. Unfortunately, because the orifices were irregular, an accurate calculation of the Free- man-Searcy correction factors" could not be made. The constants were determined in an independent experiment where the vapor pressure of copper, as measured in the alumina cell, was compared with an accurate value of the vapor pressure, which had been determined previously.4 Depletion of palladium from the surfaces of the specimens was minimal as the deflection of the cell remained constant, for at least 15 minutes, at each of the experimental temperatures. Lattice parameter measurements of the postrun alloys also indicated that no changes in the composition of the surfaces had occurred. The alloys were prepared by arc melting the requisite amounts of the 99.99 pct pure elements. The four most palladium-rich alloys were remelted in a levita-tion furnace since complete melting of the components had not occurred in the arc furnace. All of the alloys were subsequently homogenized at elevated temperatures in sealed alumina thimbles. After heat treatment, the alloys were analyzed chemically and were in essential agreement with the nominal compositions. The thermal histories and nominal compositions of the alloys are given in Table I. Lattice parameters of the heat-treated alloys were computed, by means of the method described by Mueller et a1. ,I2 from X-ray diffraction powder patterns obtained with filtered copper radiation in a 114.6-mm-diam Straumanis-type Debye-Scherrer camera. The results, which are tabulated in Table I, exhibit a slightly greater negative deviation from Vegards' law than the values reported by Raub et al.13 The diffraction lines were sharp and well-resolved and thus indicated that the alloys were homogenous. RESULTS The logarithms of the individual values of the vapor pressure of palladium were fit, by the least-squares method, as a linear function of the reciprocal of the absolute temperatures. The constants of the equations are given in Table I along with the temperature range over which the data was accumulated. The latent heat of vaporization at 298.15"K for pure palladium, calculated by the third-law method,14 showed no systematic temperature dependence. The average value of 88,920 * 20 cal per g-atom agrees favorably with the average of the results obtained in the most reliable previous investigations.15"19 The activities of palladium were computed from the vapor pressure data at 1525', 1575", and 1625OK. Consistent with the mass spectrometric study of the atomicity of palladium vapor,lg the vapor was assumed to be monoatomic. The activities of rhodium were determined by integrating the Gibbs-Duhem equation with the aid of the a function.20 In the calculations, the activities of the pure solid metals were assigned the value of unity. From the activities, the partial and integral free energies, entropies, and enthalpies of formation at 1575° K were computed; they are assembled in Table 11.

Jan 1, 1969

By Thomas H. Leggett

In speaking of the mining and economic conditions prevailing at the present time on the Rand, it is not my intention to go into the details of the mining practice, since this has been already well described both in the Transactions' and elsewhere,2 but rather to take a more comprehensive view of the industry and its surroundings as a whole, marking its general development and the lines of its future progress. In a paper entitled Deep-Level Shafts on the Witwaters-rand, with Remarks on a Method of Working the Greatest Number of Deep-Level Mines with the Fewest Possible Shafts,' presented to this Institute in August, 1900, I drew attention to the great cost of sinking the very deep vertical shafts that were then being seriously proposed as necessary for the development of the deeper areas, pointing out the strong advisability of working this ground by means of inclines to be sunk from the existing shafts of from 3,000 to 4,000 ft. in vertical depth. In this paper it is stated (p. 975): '" In short, practice upon the Rand now tends towards fewer vertical shafts and more underground inclines, especially for the very deep mining about to be undertaken." In consequence, the 6,000-ft. vertical shafts, at one time so much discuesed, have never been started, and they do not now seem likely ever to be. The necessity of placing all deep shafts further apart in order to make them control and exhaust larger areas was also dwelt upon. This economy wae vitally necessary for both

Jan 1, 1909

By E. L. Mann

Asbestos is the generic name given to a group of fibrous mineral silicates found in nature. They are all incombustible and can be separated by mechanical means into fibers of various lengths and cross sections, but each differs in chemical composition from the others. The commercial grades of asbestos consist of a spectrum of lengths and sizes and are not definitive as are most organic fibers. It is generally recognized that there are two main groups of asbestos. The first only contains the fibrous serpentine called chrysotile and comprises about 94% of the world production of asbestos. The second group contains five minerals in the amphibole series-crocidolite, amosite, anthophyllite, tremolite, and actinolite. The latter two have no commercial importance. Properties Physical The structures of asbestos fibers have been studied intensively over a number of years. X-ray diffraction patterns have been used as a means of identification and classification. Low angle X-ray scattering techniques have shown that chrysotile fibers are "hexagonally close packed" and parallel to each other, having cross-sectional diameters varying from 18Å to 300 Å units, while the amphibole fibers are many times larger in cross section, have considerably smaller surface areas, and the fibers are less symmetrical than those of chrysotile. Electron micrographs of the more common types of asbestos are shown in Figs. 1-4. Fig. 1 illustrates the softness and flexibility of chrysotile which make it suitable for textile-type products. For a number of years there was considerable controversy over the exact nature of chrysotile fiber, but the photographic evidence in Figs. 5-7 clearly show that it is tubular in structure. The curvature is the result of the mismatch in the dimensions of the silica [Si2O5] and brucite [Mg(OH)2] layers which are on the inside and outside, respectively, of a double sheet. This curvature had been predicted by Pauling (1930) years ago based on the molecular dimensions of the two component structures. In contrast to this, the structure of the amphiboles consists of two ribbon chains based on Si4O11 units separated by a band of seven cations with two hydroxyl groups attached to

Jan 1, 1983

THE refining period of an open-hearth heat blends imperceptibly into the finishing period, during which final adjustments are made in slag composition, in bath action and temperature, and in composition of the steel, in order to prepare it for casting into ingots. Operations must be governed by the consideration that alterations in the character of the heat during the finishing period must be held to a minimum. In a broad sense, the finishing and deoxidation period of a heat may be said to begin when the action of the last ore addition has ceased, and to end when the teeming of the ingots is completed. INGOT STRUCTURES A survey of the relative advantages and disadvantages of different types of ingot structure is required because deoxidation treatments during the finishing period control the amount of gas evolved during solidification and consequently determine the type of ingot structure. Four classes of ingots are recognized, depending upon the degree of deoxidation to which the steel has been subjected. These types are killed, semikilled, capped, and rimmed; typical examples of their structures are represented by ingots 1, 2, 5, and 7, respectively, of Fig 9-1. The actual ingots from which these cross sections were sketched were all poured to the same height (indicated by the dotted lines) in the same type and size of bottle-top molds. The eight drawings of the figure represent selected types of ingot structure in a continuous series from "dead killed" to "wild," resulting from variations in the total quantity of gas evolved, from none at all to copious amounts, during solidification of the steel in the mold. Killed and semikilled steels are adjacent at the "quiescent" end of the ingot structure series where only small amounts of gas are evolved. The term "quiescent" describes the action of the molten metal during and subsequent to the teeming of killed and semikilled steels. Capped and rimmed steels are adjacent at the

Jan 1, 1951

THE refining period of an open-hearth heat blends imperceptibly into the finishing period, during which final adjustments are made in slag composition, in bath action and temperature, and in composition of the steel, in order to prepare it for casting into ingots. Operations must be governed by the consideration that alterations in the character of the heat during the finishing period must be held to a minimum. In a broad sense, the finishing and deoxidation period of a heat may be said to be- gin when the action of the last ore addition has ceased, and to end when the teeming of the ingots is completed. INGOT STRUCTLIRES A survey of the relative advantages and disadvantages of different types of ingot structure is required because deoxidation treatments during the finishing period control the amount of gas evolved during solidification and consequently determine the type of ingot structure. Four classes of ingots are recognized, de- pending upon the degree of deoxidation to which the steel has been subjected. These types are killed, semikilled, capped, and rimmed; typical examples of their structures are represented by ingots 1, 2, 5, and 7, respectively, of Fig 9-1. The actual ingots from which these cross sections were sketched were all poured to the same height (indicated by the dotted lines) in the same type and size of bottle-top molds. The eight drawings of the figure represent selected types of ingot structure in a continuous series from "dead killed" to "wild," resulting from variations in the total quantity of gas evolved, from none at all to copious amounts, during solidification of the steel in the mold. Killed and semikilled steels are adjacent at the "quiescent" end of the ingot structure series where only small amounts of gas are evolved. The term "quiescent" describes the action of the molten metal during and subsequent to the teeming of killed and semikilled steels. Capped and rimmed steels are adjacent at the

Jan 1, 1964

By Frank T. Wheby

The cost of tunneling is highly sensitive to the rock characteristics through which the tunnel is to be driven. These characteristics affect in a major way the rates at which tunnels and shafts can be driven and the degree to which the openings must be supported to maintain them in a permanent stable condition. Tunnel and shaft design and cost criteria have been computerized, permitting estimates of tunnel-shaft systems to be made directly from inputs of rock mechanics characteristics and other data. Curves of quantities of steel, rock bolts, and other rock support items as related to tunnel size and rock quality designation are presented. An illustrative example of the use of the program in calculating the cost of a hypothetical tunnel system is included.

Jan 1, 1971

By J. P. Denny

The constitution of the Ga-In system was determined by thermal methods. An experimentally determined metastable equilibrium line (an extension of the indium-rich liquidus) was obtained. The various alloys were studied metallographically using polished samples obtained by a casting method. These low melting alloys required a special dry-ice assembly to maintain a suitable temperature. RECENT interest in alloys that are liquid at room temperature has led to rather extensive investigation of gallium-base alloys. Widely distributed over the earth, gallium could be produced in substantially larger quantities than at present, if a significant demand existed.' One study' has established its presence in 12 out of 14 zinc blends, in all of 15 aluminum ores, in 4 out of 12 manganese ores, in 35 out of 91 iron ores, and in all of 7 magnetite ores. It occurs as a rule in minute amounts, however, leading to high extraction costs. Recent quotations run from $2.50 to $7.50 per g. During the course of the present investigation, portions of the system Ga-In have been redeter-mined, and the results of this study are presented herein. Thermal and metallographic methods have been employed. Lecoq de Boisbaudran, the discoverer of gallium, conducted the first investigation" on Ga-In alloys in 1885. The temperatures of incipient melting, and of completion of melting, were determined at four alloy compositions. In 1936, Hansen' constructed a eutec-tic-type phase diagram for the system Ga-In, based on . work. The existence of a Ga-In compound was regarded as improbable by Hansen, and subsequent investigations are in agreement. French, Saunders, and Ingle3 conducted a more complete study of the system in 1938, using thermal methods. Their phase diagram is a eutectic type, containing a unique concave-upward liquidus. The solid-solution range of gallium in indium was reported as 9.5 pct by weight, and that of indium as less than 1 pct, at the eutectic temperature. The eutectic composition, determined as being bracketed by the compositions showing a true horizontal at the eutectic temperature (16°C), was reported as 76 5-0.5 pct Ga and 24 i 0.5 pct In. Experimental Procedure The preparation of Ga-In alloys is simplified by the low melting points involved. Various compositions were prepared by melting in pyrex tubes, using a cover of distilled water or parafin to prevent the alloys from wetting the glass wall. In all cases, the melts were homogenized. by stirring. Where possible, both cooling and melting curves were determined. The extensive undercooling of gallium was found to prohibit a satisfactory cooling-curve analysis of gallium-rich alloys, however, and transition points on the gallium side of the eutectic could be determined only by melting curves. The inverse rate method of thermal analysis proved to be most satisfactory and was used to a great extent. Various heating and cooling rates were used, ranging from 0.2" to 5.0°C per min. Low temperature melting analyses were conducted within a constant temperature bath, maintained at about 70 °C. The alloys were solidified (under water or paraffin) within a pyrex tube, using dry ice; the tube was then sealed within a cold Dewar flask, the unit transferred into the constant temperature bath, and periodic temperature readings taken. The high temperature melting-curve determinations and all cooling-curve determinations were made in a vertical tube furnace. At near-eutectic compositions, the furnace was placed within a refrigerated room held at —20°C. Accordingly, the furnace on cooling approached —20°C asymptotically and permitted the determination of those phase transitions occurring below room temperatures. Temperatures were measured with a 30-gage iron-constantan thermocouple, immersed directly in the alloy. To prevent contamination of the melt, the leads and junction were coated with Lucite, applied by painting with a solution of Lucite in ethylene dichloride. Electromotive force measurements were made with a Leeds and Northrup precision potentiometer, type 8662. The couples were calibrated against the boiling point. of water and, at lower temperatures, against a calorimeter thermometer having a Bureau of Standards certificate. The melting points of gallium and indium used in the present investigation were determined as 29.-77° and 156.1°C, in good agreement with previously reported values of 29.78°C° and 156.4"C.' The spec-

Jan 1, 1953

By C. K. Leith

THE questions as to what grades of ore it pays to conserve for the future, and the valuation of low-grade reserves, are becoming immediate and definite as applied to individual ore deposits, and seem to call for some sort of quantitative answer. Both opinion and practice involving these questions differ widely. The number of variables in this problem is so large that final solution will perhaps never be agreed upon, yet there seem to me to be certain controlling factors which can be placed in quantitative relation and serve to reduce the number of variables which it is necessary to consider in a given instance. I assume that it will not pay either for the individual or for the State to conserve any ore when the present cost of conservation (by stock piling or otherwise), when compounded at 6 per cent. interest for the number of years which would elapse before this ore is used, will exceed the profit which the ore will yield when it is used. It may be urged that any loss to the individual may be made up in gain to the State. This might be true if there was any definite limit to the amount of iron ore, but when we remember that iron makes up .4 per cent. of all the rocks of the earth and the amount of rock carrying iron in excess of 20 per cent. is for practical purposes, unlimited, it is apparent that posterity is assured of its iron ore. The changes will be mainly in methods and cost of extracting the ore. Therefore, any expenditure of money or effort now, which when compounded will exceed the worth of the effort or money needed in the future to utilize the iron, is a net loss both to the individual and to the community.

Jan 2, 1914

By R. M. Keeney

Before the outbreak of the war in 1914, the only electric-furnace smelting plant operating on a commercial basis west of the Mississippi River was an electric pig-iron plant in California; rare metal ores were not smelted, concentrates of molybdenum, tungsten, uranium, and vanadium ores being shipped East for reduction. Practically no chrome ore was being mined, and only comparatively small amounts of manganese ore. Today there are two electric smelting plants in California, one in Washington, one in lowa, and four in Colorado; two plants are under construction in California, and one in Montana. Ores of manganese, chromium, molybdenum and tungsten are now smelted in the West, and although uranium and vanadium concentrates are still shipped to the East, they will probably be treated in western plants in a short time. The four electric-furnace plants in Colorado are listed in Table 1. Table 1.—Electric Smelting Plants in Colorado Capacity. Company Location KilowattB PRoductS Tungsten Products Co........... Boulder 800 Ferrotungsten, ferromo- lybdenum. Boulder Tungsten Production Co .. Boulder 400 Ferrotungsten. Ferro Alloy Co.................. Utah Junction 1200 Ferrochrome, ferrotung- sten. Iron Mountain Alloy Co......... Utah Junction 3000 Ferromanganese. Power for all of these plants is supplied by the Colorado Power Co. The plant of the Ferro Alloy Co., at Utah Junction, contains one 750-kw., three-phase furnace, to which power is supplied by three 250-lrw. transformers, connected /Y to give 129 volts on the furnace cables, the transformer ratio being 13,200 to 75 volts. The furnace operates with an actual voltage of 120 volts, and produces about 3 tons of ferrochrome per 24 hr. from 40-per cent. Cr2O3 ore. The furnace consists of a steel shell of circular cross-section, 8 ft. (2.43 m.) in diameter by 7 ft. (2.13 m.) deep, lined with magnesite, and having three vertical carbon electrodes 12 in. (30.48 cm.) in diameter. A 450-kw. furnace, of the same size as the 750-kw. furnace, is also operated on chrome ore. This furnace is three-phase in appearance, but operates electrically as a single-phase furnace. There are three vertical

Jan 1, 1920

By Paul Beck

IT is well known that the hardness of metallic single crystals, like that of polycrystalline metals, increases during deformation (hardening by cold-work). It is also known that, as a consequence of deformation, the metallic material acquires an evident thermodynamic instability, revealed, for example, by the fact that the increased hardness gradually decreases with time, especially at elevated temperatures (softening by annealing). The temperature at which the stabilizing process begins is different for various metals, and for any metal it depends on the amount of deformation. Such stabilization of deformed metals may proceed in two different ways: through recovery, and through recrystallization. The former process allows the unstable deformed metal body to approach stability gradually and without visible change in the grain structure; the latter process, like an allotropic transformation, yields directly the undeformed stable "phase" in the form of new undeformed crystals, which, starting out of a certain number of nuclei, grow into and' consume' the deformed hard material. The extent of stability attainable through recovery is limited, espe-cially if the deformation of the metal crystal or crystals involves not only the gliding along slip planes, but also the bending of the slip lamellae, or at any rate the bending of comparatively large parts of the crystal lattice. In such cases, for instance in bent single crystals or poly-crystalline metals subjected to any deformation, recovery will not as a rule be able to restore the "straight" undeformed lattice, and stability can be attained only by recrystallization; that is, by the consumption of the bent crystal lattice parts by new, undeformed crystals-a much more drastic process. It is evident that the part of the surplus free energy stored in deformed crystals, which is present in the form of the elastic energy of the bent lamellae, is in these instances not considerably involved

Jan 1, 1937