Search Documents

By Ira B. Joralernon

THREATS of a coming metal famine in the United States have filled many columns in magazines and newspapers in the past three years. This asserted menace has diverted attention from the actual results of recent exploration. Because no one had bothered to look into the facts, the statistical experts assumed that little ore was being found. They often subtracted the staggering tonnage of metals produced during the war from earlier published reserves, and assumed that the difference was all we had left. Naturally, they shuddered, with all possible publicity. For their figures showed an imminent lack of nearly all the metals needed for an industrial civilization, as well as for mechanized war. They concluded that only wholesale imports and development and production of metals by Federal agencies could avert the famine.

Jan 1, 1948

By W. F. Rochow, W. C. Burke

Numerous designs of linings and accessories, including dams, lifters, and heat exchangers, contribute greatly to kiln efficiencies. Greater conductivity is achieved with basic brick than with fireclay and high-alumina refractories, depending largely upon the use of steel plates in radial joints between adjacent brick to increase heat transfer through the lining. Refractory lifters expose all portions of the load to radiant or convective heat and raise some portions to higher temperatures by cascading the load down through the path of the hot gases.

Jan 3, 1955

By V. J. Sikora, W. J. McGuire

Several years ago, we used an electric analogue computer to study the effect of vertical fractures on the productivity of wells in expanding fluid-drive reservoirs. The results of this work were used both as a guide to research and as a basis for the design of actual fracturing operations. In 1958, Dyes, Kemp and Caudle' published portions of the data from this study. The results were released in 1959 to service companies for use in fracturing guides. The purpose of this note is to discuss the experimental conditions and assumptions which were made to derive the information which is already partially a matter of public record. ASSUMPTIONS This study applies to fractures which extend in a vertical plane symmetrically from the well. For simplicity, we chose to study the case of a well in a square drainage area with its fractures extending toward two of its nearest neighbors. We have assumed no migration of fluid across the boundary of this area. The quadrant shown in Fig. 1 models this system. We made the usual assumptions that the reservoir is homogeneous and isotropic, that the fluid is homogeneous and that production is effected by fluid-expansion drive. We also assumed that the fracture extends from top to bottom of the reservoir. Of more practical interest is our assumption that the fracture does not change the size of the drainage area. This premise is appropriate if all the wells in the reservoir are fractured in the same way. But where a single well is fractured, its drainage area may be enlarged at the expense of its neighbors. This could be of economic importance. The assumption that the fracture will not extend beyond the established drainage area of the well also limits the application of the results. Such long frac- tures will yield benefits in excess of those predicted here. When we assume homogeneity, we disregard the frequently observed zone of damage in the vicinity of the well. Where damage is severe, the benefits resulting from by-passing it will far exceed those predicted by this study. All comparisons were made of systems producing in the semi-steady state. By this we mean that equal volumes contributed equally to flow (pressure was dropping at a uniform rate throughout the system) when the rate of flow was observed. EXPERIMENTAL SET-UP We used the pool unit of an electric analyzer' in this study. The squase drainage system of a well was rep-

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By H. J. Gerritsen

From presently available components a portable, rugged, reliable apparatus can be built which will be able to detect methane concentrations of 0.1% and lower in air. Sensitivity and design considerations of the apparatus are given. Ways to build even simpler and cheaper apparatus in the future are indicated. Traditionally the problem of detecting and monitoring the presence of dangerous gases present in small concentrations in air has been a difficult one. Whether canaries,' or sophisticated chemical or thermal conductivity methods are used, they seem to be either slow, cumbersome, or otherwise not completely satis factory. A seemingly natural way of gas detection is to measure the strength of absorption undergone by light of a wavelength that the gas to be detected absorbs. This method has been difficult to apply in view of the low power output over a narrow wavelength range in the infrared from traditional glow bar light sources. Besides, the apparatus to select such a narrow band of wavelengths is quite costly and complex. The use of a laser solves these problems simultaneously. Although a variety of lasers are available to detect a variety of gases (such as carbon monoxide or methane) whose early detection would be desirable, this paper deals exclusively with the use of lasers for methane detection. ABSORPTION SPECTRUM OF METHANE IN AIR The absorption spectrum of pure methane is very well known.2-4 There are four fundamental vibrations, all occurring in the infrared of which only two absorb strongly. They occur at 3.3 µ and 7.7 µ. The absorption spectrum is quite complicated due to the fact that the methane molecule can rotate in a variety of rotational quantum states. These rotational states are furthermore split by anharmonic forces such as the Coriolis force.4 When methane is present in air at atmospheric pressure, much of the very fine structure due to the anharmonic force is washed out since the pressure broadening is of the same magnitude as the splitting due to anharmonicity. For most of the spectrum at 3.3 µ, the rotational lines are typically separated by 0.01µ while the individual linewidth is 0.0001 µ. It is thus very important that the laser emit at a wavelength that coincides with one of these rotational lines. Before elaborating on the point that such a laser exists and how it performs, it is necessary for later discussion to point out that in the

Jan 1, 1967

By Oscar A. Glaeser

INDUSTRIAL relations in the United States Smelting Refining and Mining Company's Western operations covers the field of personnel and labor relations, and the principal aims are to render service to the employes of the Company and to its operating departments. Accident prevention Safety is a primary function. A safety engineer is employed at each operation. The wholehearted support of Company officials, staff, and the working force has been most successful in preventing accidents. Constant vigilance has been combined with a policy of building safety into all operating activities whether these are in the construction of a new facility, the developmnt of a mining system, or the direction of the working force. That this policy has produced results is attested to by the fact that the accident frequency rate at the Company's major mining operations in Utah has been reduced approximately 75 per cent in the ten-year period ending Dec. 31. 1946.

Jan 1, 1948

By G. H. K. Schenck, H. W. Robinson

Private weather forecasting services available on a contract basis can significantly reduce the uncertainty associated with weather-induced changes in mineral production and demand. Such services offer the mineral producer the opportunity for tactical and strategic response to weather conditions. There are at least 50 private meteorological consulting services as well as numerous individual meteorology consultants. Fees for services range from $150-$600 per day for one man to over $20,000 per month where a complex forecasting or modification program is undertaken.

Jan 1, 1971

AALL,Christian H.,(M '49), Asat.Research Dir , Phosphate Div Monsanto Chem.Co.,Monaanto, Tenn. AAMOT,Olav Crone, (M '29), Dir of Tech., Chromium Min. & Smelt. Co Ltd Box 6215, Hillyard, Spokane, Wash. AARING, Floyd Daniel, (J '48), Prod. Engr., Canadian Gulf Oil Co., 8035 - 102nd St., Edmonton, Alta., Canada AASE, Glenn D., (J '40), Met Engr Western Research Div. ,Amer. Smelt. & Refin. Co., Selby, Calif ABADIE, Henry G (M '43), Senior Prod Engr., Long Beach Oil Dev Co., 255 S Santa Clara Ave Long Beach 2, Calif. ABBOTT,Clarence E (M '04), Civil Engr., 901 Insurance Bldg., Raleigh, N.C. ABBOTT, John, H., (M '46), Resident Mgr., Hickman, Williams & Co., Rm 2205,230 N Michigan Ave., Chicago 1. I11.

Jan 1, 1952

By E. H. Rose

IN a year of sober reflection and stocktaking after the mineral-squandering spree of World War II, the role that beneficiation of low-grade must henceforth play in American mineral industry has become unmistakable. From the volume of research and development progress in mineral engineering during 1946, mineral dressers evidently have ample resoluteness to meet the challenge. Perhaps ,the most conspicuous trend of the year was the renascence of interest in gravity concentrating methods and more serious effort than ever before to make them effective in finer size ranges down to 200 mesh. This has been forced by the problem in iron ores where the low value of the product will not support a high flotation reagent cost, however good flotation pilot plant results may have been and however well the acute problem of variable feed may be met. The race is on between rabbit flotation and tortoise gravity methods and a surprising amount of betting money is being laid on the tortoise which already is showing previously unsuspected talent for speed. Mostly, however, a wait-and-see attitude prevails during the present preliminary heats. As evidence of the latter, two magnetic plants are now on the boards for magnetic taconites on the eastern Mesabi to establish a reprieve against the time when nonmagnetic taconites must be addressed. Incidentally, these operations will force the blast-furnace issue on preparation of fine material since a minus-100-mesh grind is contemplated.

Jan 1, 1947

By W. T. Swensen

The Anaconda Company, through its wholly owned subsidiary The Anaconda Company (Canada) I,td., has investigated, optioned and partially developed a large tonnage of iron ore amenable to magnetic concentration. The reserves are located in north central Ontario and occur within a twenty-two mile belt of layered and intricately folded metamorphic rocks, close to the north contact of an igneous complex of granite and pegmatite. There are two main ore deposits. Briarcliffe is a steep to vertically dipping body 100 to 500 feet wide and over a mile long. The Two Mile Lake deposit is flat dipping and confined to an open, asymmetrical syncline; it is approximately a mile wide and 250 to 4.00 feet thick. On its flat easterly plunge, it is saucer-like in shape and is amenable to open-pitting for an east-west distance of several thousand feet. Magnetometer surveys, confirmed by drilling, indicate at least a three mile eastward extension of this deposit. Location and Access: The property is located in the Kowkash Mining District of northwestern Ontario, roughly forty-four miles north of the community of Nakina on the main line of the Canadian National Railroad. (Fig. 1) Access during the exploration period was entirely by airplane from Nakina. (Fig. 2) More recently, Nakina itself was connected to the highway network in the Longlac-Geraldton area. The property is roughly 190 miles by existing and proposed railroad from the Great Lakes waterway system. The Trans-Canada pipeline moving natural gas from western to eastern Canada passes through Geraldton roughly 70 miles south of the property. Topography: The surface features in the area are typical of a sizeable portion of the Precambrian Canadian Shield area. Many lakes, low swampy areas, and glacial moraine-type features are common in this recently glaciated area. The average elevation is between 800 and 900 feet above sea level, and the relief is probably less than 100 feet with the greater portion of the area less than 50 feet. The topographic "highs" are formed either by outcrops that were resistant to glacial erosion or by moraines, eskers and drumlins which were deposited upon the recession of the glaciers. The better mineralized zones, composed chiefly of quartz and magnetite, commonly form ridges resistant to erosion and weathering. Previous Work: Because of the obvious outcrop of the magnetite-rich beds and knowledge gained from early developments within the general region, it is conceivable that the presence of the iron formations has been known for a good many years. The area is included in studies made by L. F. Kindle* in 1929 and 1930 for the Ontario Department *Kindle, L.F., Kowkash-Ogoki Gold Area, Ontario Department of Mines Annual Report, Vol. XL, Part IV, 1931; map 40f

Jan 1, 1961

By F. W. Lee

A GREAT CURTAILMENT of field activities among the geophysicists occurred last year, especially in prospecting for the common metals. In gold, however, an "outstanding achievement . . . was made by the engineers of Consolidated Goldfields. Here the suboutcrop of the Main Reef Series was traced from Middelvlei through properties of the westward area, a distance of from 30 to 40 miles. Here Drs. Reineche and Krahman prospected with the aid of a sensitive magnetometer and established the singularities of the various beds which heretofore had not been sufficiently appreciated. Several underlying shale beds were used to determine this suboutcrop under the dolomite. This area promises to be the equivalent of one-half the size of the present gold fields and to rank in value with the Far East Rand." The present temperature compensated magnetometers permit accurate field observations to less than 5 gammas. Since magnetic anomalies may have their origin due to a change of elevation as well as to the outcropping of a bed of another magnetically different material, intimate geological knowledge is of great assistance in the interpretation of these measurements. To what extent magnetic measurements reflect the basement when the material is homogeneous, consisting primarily of red granite, was determined by members of the Bureau of Mines and described by Dr. J. H. Swartz. Because of the diverse causes of magnetic anomalies, some of which were discussed and correlated by Stratton and Joyce upon known conditions, magnetometer measurements are often difficult to interpret.

Jan 1, 1933

IN the extra-mural service being built up by the Engineer-ing Societies Library as its finances permit, an occasional large total charge is incurred for exceptionally protracted services. A western steel company, for example; was charged the unusual fee of $500. They wanted complete informa-tion on transverse tests of steel, and asked the library to compile copies of all accessible records. Weeks -of search-ing and photoprinting produced three volumes of data. Two years afterward the company's chief engineer told the director of the library that the cost seemed high when the bill was paid but that the volumes had been in constant use. The information had been worth thousands of dollars. A client who wishes to pay no more than a moderate fee for services can state to what limit he is willing to go. Thus he may specify that he would like searches made on a particular subject but that he does not wish to exceed $5 or $30- for the information. The library is as willing to perform a small service as a large one.

Jan 3, 1928

By P. J. Closmann

Steam zone growth as a function of time has been calculated for the case of constant rate steam injection into a preheated reservoir. To simplify the calculation a linear temperature profile has been assumed in the cap and base rock at the start of steam injection. The results indicate that at early times augmentation of steam zone growth due to preheating should be greatest. At longer times the steam zone development becomes close to that calculated with no preheating. INTRODUCTION With the increasing application of thermal recovery processes to recover viscous oil, cyclic steam injection has become important in many large-scale projects. In this process, the cycle of steam injection followed by oil production is repeated a number of times. At the beginning of the second and later cycles, steam is injected into a reservoir that has already been heated but that has lost part of its heat both in produced fluids and by conductive heat loss away from the injection zone. In such a case, the temperature level of the injection zone and the temperature distribution of the surrounding rock will affect the growth of the steam zone developed during the subsequent steam injection. Knowledge of the size of steam zone developed is important in determining the amount of oil displaced and the extent of heating in the reservoir. It is also useful to be able to compute the size of the steam zone for cases where thief zones take most of the injected steam. This paper presents a fairly straightforward method of estimating the steam zone developed in a preheated formation, based on certain simplifying assumptions. Some cases of steam injection into a reservoir at its original temperature have already been considered elsewhere.1-3 Because it is difficult or impossible to obtain an accurate representation of the temperature distribution in the reservoir some time after initial heating has taken place, in this work, a linear temperature profile in the cap and base rock is assumed (Figs. 1A and 1B). The linear profile has the advantage of yielding heat flow equations that

Jan 1, 1969

NEW YORK SECTION J. E. Johnson, Jr., Chairman Edgar Rickard, Vice Chairman. D. M. Liddell, Secretary, 7 Wall St., New York, N.Y. C. A. Bohn, Treasurer John V. N. Dorr Lewis W. Francis. The annual meeting of the New York Section was held on Wednesday, June 6, with about 40 members in attendance. The treasurer re a brief summary of-the financial statement for the year, and the secretary's report was read. These reports were ordered placed on file together with the report of the auditors for the two previous years.

Jan 8, 1917

By Kenneth S. Ritchie

TOO often, many foremen; superintendents, managers, and executives, "The Bosses" of the oil and mining industries, do not fully realize: (1) How much personal actions '.on the job" may reduce their effectiveness in getting work done; and, (2) The importance of harmonious relations with their fellow men. Today. these qualities of personality in the people entrusted with the positions of responsibility are more important than ever with the shortages of labor so critical in vital war production. Likewise, many engineers do not fully realize that their work is essentially executive in character; i.e., other people do the actual labor. Without their help. the engineer's work would not be done. A clearer appreciation of this fact would increase their interest: (1) in the nontechnical aspects of their work. and, (2)in their relations with others, particularly the individuals in their own organization. Consequently, these engineers would be more successful in equipping themselves for greater responsibilities and increased remuneration.

Jan 1, 1944

By Enrique Touceda

FOR a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At -the outbreak of the war the firm decided to specialize in the manufacture f propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods f manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual -blade mold formed, the pattern is then rotated on the spindle to the position- for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this practice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface f each blade must be chipped too the templet and through this procedure chipped to such accuracy, as will be required for a static balance. Inasmuch as the' work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin f the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days f foundry work and about the same length of, time for the machining. Through the use f the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity, with any particular propeller-wheel design,

Jan 4, 1921

By C. H. Mathewson

UNFORTUNATE evasions of metals specifications recently brought to public attention through news items and editorials have caused executives of at least two great corporations to set up defensive procedures and to re¬affirm the patriotic purpose and conscientious effort of their plants in this battle of production. Whatever the exact conditions affecting these cases, in which the public interest has been safe-guarded by vigorous action, my reaction to such offenses in general is a feeling that they arise from the pressure and limitations that afflict our overextended war effort and that inevitably there will be more of them, doubtless more and more expertly conceived and less and less subject to detection as simple faked, or substituted analyses or tests. To the ladies, who doubtless are already beginning to ac¬quire a sense of painful resignation to a dry technical talk, may I say that the cookbook is full of specifications which customarily are varied within rather wide limits but it is generally recognized that the proof of the pudding is in the eating without regard to its exact composition or some scientific evaluation of its texture.

Jan 1, 1943

By AIME AIME

THIS journal is fully indexed-every issue, as soon as published-in a set of card?, which thus brings ready to your hand any article on any subject in this journal or in any one of 1700 other journals in all languages. This Engineering Index Service, instituted in January, 1928, is to be found in the Public Libraries of Newark, Cleveland, Bridgeport, Baltimore and the John Crerar Library, Chicago. Engineers in any field who live or work in New Jersey will find this mammoth index to the latest engineering literature in the Public Library of Newark, N. J.

Jan 1, 1929

By G. V. Smith, C. O. Tarr, R. F. Miller

Metallurgists have long recognized that the Fe3C type of carbide is not a stable phase in steel and that, given sufficient time, it will decompose with formation of graphite, at least at temperatures below about 205o°F.l This slow graphitization has never been of much concern to users of hypoeutectoid steels, for in such steels it occurs only during prolonged exposure at elevated temperature. In I935, Kinzel and Moore2 reported complete graphitization of the carbide of a 0. I5 per cent carbon steel that had been in service for about 26,000 hr. at a temperature of about IIOO° to 12oo°F. In discussing this paper, both Mathews and Sauveur reported graphitization of slightly hypereutectoid steels. In an extensive investigation of graphitization of high-purity iron-carbon alloys, Wells1 produced graphite at 7oo°C. (I29o°F.) in an alloy containing as little as 0.13 per cent carbon, and showed that graphite may precipitate either directly from austenite or from decomposition of Fe3C, also that the rate of graphitization tends to increase with increase of temperature, at least up to a certain point, and with the presence of graphite nuclei. Jenkins, Mellor and Jenkinson,3 studying the structural changes in carbon steels ranging from 0.17 to 1.14 per cent carbon during stress-rupture tests at elevated temperature, observed graphite in an aluminum-killed 0.40 per cent carbon steel after fracture in 4340 hr. under a stress of 17,900 lb. per sq. in. at 840°F. and in many of the steels after stress-rupture test at 12oo°F. Unstressed samples of 0.60, 0.86 and I.I4 per cent carbon steels graphitized almost completely in 360 hr. at I200°F., while samples of 0.90 and 1.10 per cent carbon steels were somewhat graphitized, and steels containing 0.24, 0.40 and 0.57 per cent carbon showed no sign of graphite. Their results indicate that graphite precipitates the more readily the higher the carbon content, though this tendency is influenced to some extent by deoxidation practice, and that graphitization is accelerated by plastic deformation. In a recent study of the graphitization of 0.4 and 0.6 per cent carbon steel strip, made by M. A. Hughes,4 it was found that at I2oo°F. graphite appeared after 72 hr. in aluminum-killed but not in silicon-killed steel, and that the rate of graphitization was increased by slow cooling from I6oo°F. and by cold-working prior to annealing. In creep tests of normalized 0.15 per cent carbon steel killed with 2.5 Ib. of aluminum per ton, at the U. S. Steel Corporation laboratory at Kearny, spheroidization and some graphitization were found after 3000 hr. at Iooo°F. under a stress as low as 1500 lb. per sq. inch. .

Jan 1, 1944

By C. O. Tarr, G. V. Smith, R. F. Miller

Metallurgists have long recognized that the Fe3C type of carbide is not a stable phase in steel and that, given sufficient time, it will decompose with formation of graphite, at least at temperatures below about 205o°F.l This slow graphitization has never been of much concern to users of hypoeutectoid steels, for in such steels it occurs only during prolonged exposure at elevated temperature. In I935, Kinzel and Moore2 reported complete graphitization of the carbide of a 0. I5 per cent carbon steel that had been in service for about 26,000 hr. at a temperature of about IIOO° to 12oo°F. In discussing this paper, both Mathews and Sauveur reported graphitization of slightly hypereutectoid steels. In an extensive investigation of graphitization of high-purity iron-carbon alloys, Wells1 produced graphite at 7oo°C. (I29o°F.) in an alloy containing as little as 0.13 per cent carbon, and showed that graphite may precipitate either directly from austenite or from decomposition of Fe3C, also that the rate of graphitization tends to increase with increase of temperature, at least up to a certain point, and with the presence of graphite nuclei. Jenkins, Mellor and Jenkinson,3 studying the structural changes in carbon steels ranging from 0.17 to 1.14 per cent carbon during stress-rupture tests at elevated temperature, observed graphite in an aluminum-killed 0.40 per cent carbon steel after fracture in 4340 hr. under a stress of 17,900 lb. per sq. in. at 840°F. and in many of the steels after stress-rupture test at 12oo°F. Unstressed samples of 0.60, 0.86 and I.I4 per cent carbon steels graphitized almost completely in 360 hr. at I200°F., while samples of 0.90 and 1.10 per cent carbon steels were somewhat graphitized, and steels containing 0.24, 0.40 and 0.57 per cent carbon showed no sign of graphite. Their results indicate that graphite precipitates the more readily the higher the carbon content, though this tendency is influenced to some extent by deoxidation practice, and that graphitization is accelerated by plastic deformation. In a recent study of the graphitization of 0.4 and 0.6 per cent carbon steel strip, made by M. A. Hughes,4 it was found that at I2oo°F. graphite appeared after 72 hr. in aluminum-killed but not in silicon-killed steel, and that the rate of graphitization was increased by slow cooling from I6oo°F. and by cold-working prior to annealing. In creep tests of normalized 0.15 per cent carbon steel killed with 2.5 Ib. of aluminum per ton, at the U. S. Steel Corporation laboratory at Kearny, spheroidization and some graphitization were found after 3000 hr. at Iooo°F. under a stress as low as 1500 lb. per sq. inch. .

Jan 1, 1944