Search Documents

Jan 1, 1890

By A. B., Sabin

THERE are many who know The Lucky Tiger and will remember the 35-mile road from Esqueda, a station on The Nacozari Railroad in northern Sonora, Mexico. They will remember the box canyons of the Agua Caliente Mountains which are scarcely wide enough for two cars to pass; the Bavispe River which one hour may be a lazy trickle and the next a sweeping torrent, and the tortuous road up Tigre and Espuela canyons, now following the wash, now hugging some gigantic red cliff. It is still the same. From camp the view of the distant blue-gray mountains is the same. But one thing a visitor of a former day might miss: The hundreds of pack mules and burros, loaded with concentrates from the mill, which used to take most of the road and show up at the most inopportune places, have almost disappeared, replaced of course by the auto truck.

Jan 1, 1929

PHILIP D. WILSON,* Warren, Ariz. (written discussiont).-Mr. Tovote's idea of attempting to classify according to their broad geologic relations the ore deposits and prospects of the Southwest is an admirable one. Attempts have been made to evolve some comprehensive scheme of classification that would be of practical assistance in determining the possible value of prospects, but the ore deposits are too varied in type, form, genesis, and distribution to lend themselves readily to any definite, scientific pigeon-holing. The classification Mr. Tovote recommends, combining the age of the mineralization with the type of the rock supposed to be its source, is open to criticism even on the evidence he presents. The age of many deposits is not nor can be definitely determined because of the absence of sedimentary rocks in their vicinity. Furthermore, the character of the mineralizing solutions has, in a large majority of cases, no relation to the composition of the associated igneous rock. While the solutions may have originated in the same magma, they were usually a much later manifestation of it, often appearing after the intrusive rock had completely solidified and been subsequently crushed and fractured, and in many cases the chemical difference is very marked. It is true that igneous activity in the Southwest is definitely related to-certain geologic periods. The statement, however, that no ore deposits can unmistakably be referred to periods earlier than late Cretaceous is not supported by fact. The bonanza copper orebodies of the Jerome District are definitely pre-Cambrian. As suggested by J. R. Finlay,1 they are probably post-Beltian or late Algonkian in age, perhaps related to the same great mountain-making period as the copper deposits in the Keweenawan series of Lake Superior and the Sudbury, Porcupine, and Cobalt deposits of Ontario. The proof that they are pre-Paleozoic may be summarized as follows: 1. The pre-Cambrian complex in which they occur is overlaid by a great thickness of Paleozoic sediments with the Tonto or Tapeats sandstone at their base. The only primary mineralization in these sediments is an economically unimportant one connected with very recent basalt. 2. In the United Verde Extension mine, the gossan over the great orebody extends to the old pre-Cambrian surface where it is directly

Jan 2, 1919

By W. A. Backofen, D. L. Holt

Push-pull fatigue tests have been carried out at 4.2°K, 77oK, and room temperature on two poly crystalline materials of widely different stacking-fault energy (?): pure copper (? - 70 ergs per sq cm) and the Cu-8 wt pct A1 alloy (? - 2.8 ergs per sq cm). Constant stress-amplilude was imposed and measurement was made of the plastic-strain amplitude (ep) at saturation. Lives extended from 104 to 106 cycles. Designating lives at the various temperatures by NRT, N77, and N4.2. the ratios N77/NNT and N4.2/N77 ranged from 3.5 to 18 under the condition of common Ep . Metallo-graphic examination revealed different crack morphology in Cu-8 Al fatigued at room temperature, and at 77" and 4.2oK. At room temperature, cracks lay in or near grain and lain boundavies; at 77o and 4.2oK. cvacks were transcrystalline. Tests on single crystals of Cu-8 A1 showed that such a change in the cracking mode in polycrystallitle material accounted for a factor of- about 3.25 in N77/NRT . The longer life at lower tewperatztre (conslant cp) has heels attributed to two deuelopinents: a reduced production of the dislocation tangles and subgrain boundaries which serve as paths of rapid cracking, and suppression of oxygen chetni-sorption at the crack tip It was concluded that in both materials the luller accounted for an extension of the life at 4.2oK beyond that at room temperature by a factor of 15. XV ECENT experiments on the fatigue of Cu-A1 alloys in the so-called high-cycle range (greater than lo4 cycles) have emphasized the importance of stacking-fault energy (y) as a quantity affecting crack propagation rate and fatigue life.1,2 It was found in comparisons at essentially fixed plastic-strain amplitude that crack growth rate decreased by a factor of about 5 over the composition range from copper (? - 70 ergs per sq cm) to Cu-8 wt pct Al (? - 2.8 ergs per sq cm). The argument was made that, when stacking-fault energy is high, cross slip and climb are favored, so that dislocation tangles and/or subgrain boundaries form more readily under cyclic loading. Since the boundaries and tangles act as paths of rapid crack propagation ,3, 4 life is shortened as a result. However, when stacking-fault energy is reduced (as by alloying), cross slip and climb become more difficult, with the result that substructure formation is retarded and growth rate is also reduced. A purpose of the present work was to investigate the substructure effect in relation to temperature. As temperature is lowered, ? is varied only slightly (if at all), but decreased thermal activation can interfere with cross slip and climb. Thus substructure formation could be curtailed and life increased. Fatigue life in the high-cycle range is also known to be strongly influenced by environment. Working with copper, Wadsworth and Hutchings observed that life in a vacuum of 10-8 mm Hg exceeded life in air by a factor of 20.5 They isolated oxygen as the agent that furthered cracking. While the details are still unclear, a requirement in any mechanism of oxygen-accelerated cracking is that there be chemisorption at the crack tip. That could prevent welding on the compression half cycle,= interfere with reversal of slip,1, 6 or aid in breaking metal-metal bonds at the crack tip.5'7 In the work being reported here, temperature was lowered by immersion in liquid nitrogen and helium, which also served to reduce both the oxygen concentration and chemisorption rate. A possible effect upon life, i.e., a lengthening, had to be recognized. Several researchers have determined fatigue lives at low temperatures presenting their results in the form of stress amplitude (S) vs cycles in life (N) curves.8-11 Such curves reflect, primarily, the fact that metal is strengthened by lowering temperature; effects of substructure and changing environment tend to be masked. The difficulty can be overcome by comparisons based on identical plastic-strain amplitudes, and in the present work the dependence of life on both plastic strain and stress amplitude was established. EXPERIMENTAL Materials. The principal materials were polycrystal-line copper (? - 70 ergs per sq cm)" and the Cu-8 wt pct Al alloy (? - 2.8 ergs per sq cm),I3 the latter being near the limit of solubility of aluminum in copper and having, therefore, the lowest stacking-fault energy in the CU-Al system. Specimens were machined from 0.118-in.-diam cold-swaged rods of high-purity (99.999 pct) copper and the Cu-8 Al alloy, the latter produced initially in a graphite boat by induction vacuum melting a mixture of 99.999 pct Cu and 99.99 pct Al. The machined specimens were annealed to produce mean grain diameters of about 0.070 mm in copper and 0.190 mm in the alloy. Specimen dimensions are given in Fig. 1. Values of the tensile yield stress, ultimate strength, uniform strain (determined by the Considgre construction), and reduction of area, for both materials at 4.2oK, 77oK, and room temperature, are listed in Table I. The tensile apparatus in which these results were obtained has already been described.14 Apparatus. Specimens were fatigued in push-pull with a machine that is illustrated schematically in Fig. 2. The specimen is first soldered into the top grip (1) with Woods metal, and the grip is then screwed into the inner tube (2) which is connected to the drive rod of the Goodmans vibration genera-

Jan 1, 1968

By J. B. Clemmer, P. E. Churchward, C. Rampacek

A cyclic method for processing manganese ores using sodium sulphate as the basic reagent is described. Sodium sulphate is electrolyzed in a diaphragm cell to give an anolyte-containing agentisdescribed.Sodiumsulphuric acid and a catholyte-containing iselectrolyzedincaustic soda, a part of which is carbonated in a cyclic manner to form soda ash. The reduced ore is leached with the anolyte to dissolve the manganese and the impurities are precipitated by addition of catholyte. Manganese in the pregnant todissolvethemanganeseandtheimpuritiessolution is precipitated as synthetic rhodochrosite with a carbonated catholyte, and sodium sulphate is regenerated. Calcining the manganese carbonate gives a high grade product and the carbon dioxide is returned to the carbonation step. The results of laboratory tests using cells equipped with synthetic-fiber diaphragms and permselective membranes, which permit transfer of anions or cations during electrolysis, are described. A METHOD which has been considered for pro-cessing manganese ores under emergency conditions to recover a product suitable for smelting to ferromanganese involves reductive roasting of the ore for leaching with dilute sulphuric acid followed by precipitation of the manganese from the purified pregnant solution with sodium carbonate. Although the process is operable and involves no novel or untried steps, it is noncyclic in regard to reagents. Research seemed warranted to determine if a cyclic process could be developed by electrolyzing the sodium sulphate formed during precipitation of the manganese with soda ash to regenerate sulphuric acid and sodium hydroxide. Reduced ore would be leached with acid anolyte to dissolve the manganese. The iron, alumina, and other dissolved impurities would be precipitated with the caustic catholyte, and the manganese in the purified pregnant solution would be precipitated as artificial rhodochrosite with carbonated catholyte to regenerate simultaneously sodium sulphate for electrolysis. Waste boiler gas and CO, from calcining the manganese precipitate would be recycled for carbonation of the caustic catholyte. There is a surprising lack of data in the technical literature on diaphragm electrolysis of sodium sulphate. One of the more comprehensive papers, by Atwell and Fuwa, describes the problem involved in electrolyzing byproduct sodium sulphate from the viscose process with particular regard to the design and operation of asbestos diaphragm cells. Frisk' also investigated electrolysis of sodium sulphate from viscose-spinning baths to recover caustic soda and sulphuric acid. The objective in these investigations was to produce, by electrolysis and evaporation, a concentrated caustic-soda solution and a sulphuric-acid solution low in sodium sulphate. Because of these requirements, the process was not too attractive despite a favorable yield of caustic and acid with a reasonable power consumption. Because strong acid and base are not required for processing manganese ores and nonelectrolyzed sodium sulphate is not objectionable in either reagent, the present problem was somewhat simpler than that of these investigators. The purpose of this report is to summarize briefly the results of laboratory electrolysis of commercial sodium sulphate in diaphragm cells of different types and the application of the acid and caustic for processing manganese ores in a cyclic manner. Electrolysis in Permeable Diaphragm Cells The principal problem in electrolyzing sodium sulphate in a permeable diaphragm cell is to prevent mixing of the acid and base formed in the anode and cathode compartments. It is not enough to separate the anolyte and catholyte by a single diaphragm. A three-compartment cell in which the sodium-sulphate solution is fed to the center compartment and flows through the permeable diaphragms to the anode and cathode compartments is more efficient electrically. Diaphragms should be porous enough to allow flow of solution to outer compartments but tight enough to prevent gross mixing of the anolyte and catholyte. In addition to being resistant to acid and alkali, the diaphragms should offer minimum resistance to the flow of current. It is also important that the electrolyte contain a high concentration of sodium sulphate to furnish an abundance of sodium and sulphate ions and thereby decrease the current carried by hydrogen and hydroxyl ions. A practical limitation of sodium-sulphate concentration is imposed by the decreased solubility of sodium sulphate with decreasing temperature. At 20°C, a concentration of 200 g per liter sodium sulphate can be maintained. Little is gained in conductivity by using a concentration greater than 200 g per liter. The small-scale continuous electrolysis tests were made in a 12x12 in. open-top bakelite cell equipped

Jan 1, 1956

By Chung Yu Wang, Guy C. Riddle

There are found in nature upward of II2 minerals containing antimony, but only a few of them, listed in Table I, can be considered as antimony ore-forming minerals. Stibnite (Sb2S3), antimony sulphide or glance, is the principal ore of antimony. The oxide ores—cervantite, kermesite, valentinite, sernarmontite—occur sparingly in nature. Dry methods are generally adopted for the extraction of the metal. Electrometal-lurgical methods have had much attention in America and Germany and have not yet found, on economic grounds, practical or extended application, except in a few places. During recent years, treatment of the poor grades of the ore, especially sulphide, by ore-dressing methods, has commanded some attention and been adopted at a few plants. The impure sulphide of antimony, resulting from the liquation process, is called lLneedle," "liquated" or "crude" anti- mony, and the refined metal itself is called antimony "regulus." The different processes for the treatment of antimony ores are shown in the diagram of Fig. I. Liquation of Crude Antimony The first step in the smelting of antimony is a simple one, the process of LLliquation," which produces crude or needle antimony. Ores containing $ 50 per cent Sb are used in the liquation process for the production of crude. The temperature required for liquation is between 550' and 600°C. Ores to be liquated are broken to about walnut size. If the pieces are larger than this, the low heat used will not penetrate' effectively, and if they are smaller the ore tends to pack too closely for adequate penetration. A packed charge also prevents the free escape of the fused sulphide. Intermittent Liquation in Crucibles The unique type of furnace that is in use in China for smelting is not highly efficient but is simple in construction and operation. The furnace is generally built

Jan 1, 1944

By V. J. Decarlo, J. J. Gilman

POLISHING pure zinc differs somewhat from polishing less reactive metals. The problem is not that of finding a suitable reagent, but rather of producing the polish in such a way that the surface remains polished after it is removed from the polishing bath. In other words., the anodic film that is vital to the polishing mechanism' must be tightly adherent and nonporous. It is usually desirable that it be thin. Polishing solutions consist of proper proportions of an acid and a strong oxidizing agent. In electro-polishing, the external circuit acts as the oxidizing agent. The proportions are critical because the essential surface film must be maintained at approximately constant thickness during the polishing process. In the case of zinc, chiefly two oxidizing agents, chromic and nitric acids, have been used. The simplest polishing reagent is concentrated nitric acid. However, it has certain disadvantages. It tends to pit: an excessive amount of heat is evolved during polishing; and the oxide film that it produces is not very stable, so that the polished sur-

Jan 1, 1957

By Frank J. Markewicz, William Lodding

Greensand, greensand marl, and green earth are names given to sediments rich in the bluish green to greenish black mineral known as glauconite by the mineralogist. The word glauconite is from the Greek word glaukos, meaning bluish green. The term "greensand" as a rock name for a glauconite-bearing sediment is more appropriate than "greensand marl," a term that has been doggedly perpetuated in the literature. Because of its potash and phosphate content, greensand was dug and marketed as a fertilizer and soil conditioner for more than 100 years. The advent of prepared fertilizers with adjustable nutrient ratios led to the decline of green- sand for agricultural application. The material has since been recognized for use in water treatment. Unfortunately, in spite of large reserves and worldwide distribution, the mineral has not been utilized to any significant commercial extent because no major application has been found for a substance with its chemical composition and properties. This lack is probably due to a paucity of research on its potential commercial application. Extraction of potash received considerable attention during and just after World War I. Because of relatively high extraction costs and generally low potash content (up to 8%), glauconite lost its appeal as a source of this commodity. Historical Background Greensand was used as a fertilizer in New Jersey in the latter part of the 1700s. During the early 1800s its use became more common; applications of up to 100 tons per acre were sometimes made, although recommendations for agricultural use suggested 20 to 50 tons per acre (Tedrow, 1957). Many crops, especially the forage type, were said to improve with greensand application; however, because of slow release of potash, large quantities were required. Certain greensands that contain sulfur and sulfide minerals are harmful to plant growth, and these were classified as "poison," "burning," or "black marls." The availability of higher-grade potash salts from other mineral sources, and the manufacture of prepared fertilizers, displaced the agricultural use of green- sand during the later 1800s. During the mid-1800s the domestic greensand industry, centered in a small section of the eastern United States, grossed more than $500,000 per year. Toward the end of the century, annual production had dwindled to less than $100,000. By 1910 there were only six or eight greensand producers, grossing less than $5000 (Tyler, 1934). There was a small revival in the industry during World War I because of the curtailment of foreign potash, especially from Germany. During the later 1940s and early 1950s greensand was again recommended as a food nutrient for plants and farm crops. Agronomic studies discussed its potential as a soil additive that gradually releases potash and many trace- element nutrients essential for plant growth (Tedrow, 1957). Greensand was sold with the idea that it would condition soil and absorb and hold water while its base-exchange properties would release trace elements. For a short time glauconite was utilized in certain parts of New Jersey as a binding additive in the brick industry, and in the 1800s for making green glass (Cook, 1868). In the early 1900s the base-exchange property of glauconite was recognized for water treatment, and the mineral gained acceptance as a water softener. Mansfield ( 1922) does not mention base-exchange; however, the base ex-

Jan 1, 1975

By K. J. McGrew, J. W. Murphy

Introduction Maximization of profit consistent with environmental protection is the principal goal of new applications development for any conventional or in situ mining technique. Efficient evaluation of all the parameters that contribute to mining costs and production hinges on proper design and evaluation of testing programs and data. The program discussed uses several field and laboratory procedures to estimate ore deposit characteristics and optimize lixiviant compositions. Ore characteristics and lixiviant compositions are then used in a long path leaching test (stream tube test). Stream tube test data are analyzed by mathematical models with computer assistance to predict such wellfield rate parameters as target metal production, lixiviant consumption, and restoration. When these predicted rates are combined with market values for target metals, capital expenditures, prices of lixiviant chemicals, and other economic variables (labor costs, power rates, and licensing fees), an assessment of the relative feasibility of various proposed mining plans is possible. The flowsheet in Fig. 1 illustrates this process. [ ] Field and Laboratory Procedures In general terms, the procedures followed in the evaluation of an in situ leaching application aim at accomplishing: •rapid leaching and maximum recovery of the target metal in a marketable form, •low consumption of lixiviant chemicals, •unquestionably satisfactory restoration of the mined aquifer, and •minimization of capital and operating costs for the above through development of an optimum mine plan. Keeping these goals in mind, the following minimum test program is generally recommended. Geology •Estimate of ore reserves and their variability. •Average disequilibrium value for uranium deposits. •Ore thickness, depth to ore, water level, degree of confinement, and consolidation. •Characterization of quality and quantity of other ore deposit constituents (e.g. sulfide minerals, ion exchange parameters). Hydrology •Single well pump and injectivity test. •Downhole vertical permeability test to compare flow rates of barren and mineralized formations. •Groundwater quality as it may affect licensing, hydro metallurgy, and restoration. Hydrometallurgy • Flask or autoclave tests for optimization of lixiviant parameters and determination of specific reaction rate constants. • Flask or autoclave tests for assessing amenability of lixiviant solutions with ore, consumption of lixiviant, stability of metal in solution contacting ore, and environmentally important species mobilized. • A long-path leach test for modeling the behavior of the lixiviant solution flowing through a long mineralized streamline (stream tube testing). •Metal recovery tests from lixiviant solutions (ion exchange, electrowinning, etc.). •Lixiviant regeneration tests. •Environmental restoration tests.

Jan 1, 1985

By J. Szekely, P. Tarassoff, N. J. Themelis

In a copper converter air enters the bath in the form of turbulent jets. The interaction of these jets with the molten matte is fundamental to the converting process. In the present study, an equation is derived to describe the trajectory of a gas jet in a liquid. Calculated and experimental results for air jets injected into water are in good agreement. The trajectories of air jets in copper matte are predicted. THE air injected through the tuyeres of a Peirce-Smith copper converter emerges into the bath of molten matte in the form of a highly turbulent jet. The air jets affect a number of chemical and physical processes occurring in the converter: i) Converting Rate. It is generally recognized that the production capacity of a converter is limited by the flow of air which can be injected through the tuyeres and by the oxygen efficiency. In turn, the air flow is limited by pressure drop considerations or by the amount of splashing within the converter. ii) Oxygen Efficiency. This depends on the dispersion of the air jet in the liquid bath, and its trajectory through the bath. iii) Mixing. The jets act as mixing devices by transferring momentum energy to the bath; in this way the heat generated by the converting reactions occurring in the jets is distributed through the bath. iv) Refractory Wear. The proximity of the jets, which are centers of heat generation, to the refractories in the tuyere zone may have an important effect on refractory life. Mixing conditions in the bath will also influence refractory erosion. v) Splashing, and Accretion Build-Up. The energy of the jets is not dissipated entirely in mixing the bath. particles of liquid are carried out kith the gas above the surface of the bath in the form of liquid spouts and droplets. These result in the undesirable build-up of accretions on the converter mouth, and dust losses in the flue gas. Despite the importance of the interaction of the air jets and the matte in a converter, very few studies of the fluid dynamics of converting have been reported in the literature. Metallurgists in the USSR appear to have been more concerned with the subject than their Western counterparts. Deev et al.1 studied the interaction of an air jet with aqueous solutions in a converter model and qualitatively determined the tuyere air velocity and tuyere inclination which produced the most favorable results with respect to good mixing in the bath, and minimum splashing. Shalygin and Meyer-ovich2 also examined the air-matte physical interaction both in models and in industrial converters; they concluded that in conventional converting practice, there was no significant penetration of the air jets into the matte layer, and consequently the converting reactions occurred mainly in a zone adjacent to the tuyeres. The behavior of air jets in a converter bath, and the aerodynamic characteristics of tuyeres are discussed at length in a monograph on converting by Shalygin.3 However, the description of the phenomena occurring in the converter bath is largely qualitative. The side-blown Bessemer converter for steelmak-ing is very similar to the Peirce-Smith copper converter. Among the few investigations of the behavior of air jets in the bath of a Bessemer converter are those of Kootz and Gille4 who studied splashing in the course of an investigation on the effect of blowing conditions and converter shape on nitrogen pick-up in Bessemer steel. They found that during blowing standing waves were formed on the surface of the bath; the amplitude of the waves increased with the depth and angle of tuyere immersion until the whole bath moved backwards and forwards causing heavy splashing. Kazanstev5 used a model of a Bessemer converter to obtain correlations between the axial velocity of a gas jet and distance from the tuyere orifice and the Froude number of the jet. shalygin3 used these results to calculate the horizontal penetration of an air jet in a copper converter; the penetration was defined as the distance in which the axial jet velocity decreased to 10 pct of its initial value. However, the rising trajectory of the jet was not taken into account. In the absence of quantitative information on the fluid dynamics of converting, the design of copper converters has been based mainly on operating experience. Such experience tends to vary widely from smelter to smelter., This is reflected in Table I which is based on data compiled by Lathe and Hodnett.6 Aside from a rough, and perhaps obvious correlation between the total air flow and converter volume, Fig. 1, no pattern emerges from the data. For example, tuyere throat air velocities vary from 215 to 465 ft per sec in converters of the same size, for little apparent reason. The air jet energy input per cubic foot of converter volume, which may be taken as a measure of the amount of mixing in the converter bath, also varies greatly. A recent analysis of converter data by Milliken and Hofinger7 has also revealed unexplained variations in operating parameters. It is believed that by gaining a better understanding of the fluid dynamics of converting a more rational basis may be provided for the design of converters. In particular, it is proposed that if one takes into account the desirable criteria of a high converting rate, high oxygen efficiency and long refractory life, there should be an optimum configuration of tuyere air flow for a converter of a given diameter. The present investigation is concerned with the form and trajectory of an air jet in a converter bath. The general theory of turbulent jets has been expounded by Schlichting8 and Abramovich.9 However, most experi-

Jan 1, 1970

By A. F. Buddington

INTRODUCTION EVER since a genetic connection between many ore deposits and magmas began to be widely recognized, some two-score years ago, there has been much discussion of the complex and intricate problem of the genetic association of specific kinds of mineralization with specific kinds of igneous rocks. General discussions of the latter problem and pertinent data have been given by S. F. Emmons, Kemp, Lindgren, Niggli, Rastall, Spurr, Vogt, and others. In this paper no attempt is made to deal with mineral deposits genetically associated with volcanic rocks, but only with those presumed to be related to exposed intrusive masses. The writer is indebted to E. S. Bastin, F. F. Grout, Edward Sampson, and to the members of the committee in charge of the preparation of the volume, for a critical reading of the manuscript and many worth-while suggestions.

Jan 1, 1933

By Frank C. Kelton

A method is outlined for the analysis of large cores, developed primarily for the purpose of obtaining reliable data on fractured or vugular limestones. Porosity and fluid saturations are determined by a modified Dean-Stark extraction after initially bringing the samples to 100 per cent liquid saturation by a vacuum-pressure method. Horizontal permeabilities on the whole samples are determined in two directions, parallel and perpendicular to the di-rection of principal fracturing. Results are presented for various types of formations. A comparison is made between data obtained by this special method and the method of conventional analysis, and discussion is given of the relative advantages and limitations of each. In view of this comparison a modified method for the analysis of fractured and vugular formations is proposed, which method retains the advantages of the previously outlined techniques but gives promise of speeding up the analysis. INTRODUCTION For many years the greater part of the production in the Permian Basin was from formations of Permian and Pennsylvanian age. While production from these formations is still the predominant production. deeper prospecting has brought to light older formations with oil productive characteristics. Attempts to core these deeper horizons were at first usually characterized by poor recovery. The old rule of thumb, "good core recovery — poor well" was originated and remained in effect until recently. With the advent of diamond coring and the increased efficiency in drilling and coring operations. the old adage has lost its significance. Formations of Devonian. Silurian and Ordo-vician ages were successfully cored with varying degrees of recovery. The cores thus obtained were surprising and in some case; disappointing. Good recovery from these formations led to speculation as to the feasibility of analysis and the meaning of data obtained from conventional analysis. Commercial laboratories were engaged to analyze these cores. and their results indicated that data obtained by conventional methods would be of little value. From visual inspection it was apparent that in many cases the effective porosity for storage of hydrocarbons. and permeability. were contained largely in fractures and solution cavities rather than in the primary crystalline structure of the formation. In other cases the solution cavities augmented the effective porosity of the primary crystalline structure, or fractures enhanced the permeabiilty of the latter so that the formation might respond favorably to acidization and become commercially productive. Since the spacing of the cavities and fractures was often comparable to the core diameter, it was evident that the entire core should he analyzed instead of small fragments. On the basis of these observations, commercial laboratories were requested to devise a system of analysis which would yield data of practical value. Pro- cedures have accordingly been developed which seem to meet this requirement, and to date nearly 12,000 large core samples have been analyzed. It is the purpose of this paper to describe the methods used, to present typical results for several fractured formations and to compare the data obtained by this special analysis with that obtained by conventional analysis. Certain modifications and alternative procedures are finally suggested to speed up the analysis. CORE ANALYSIS PROCEDURE Fluid Saturations and Porosity The core sample, in segments up to 15 in. in length. is marked, weighed and examined under ultra-violet light to determine the presence of oil saturation. If present, the approximate quantity of oil and its location on intercrystalline, fracture or vugular surfaces is noted. This information is carefully recorded. The degree of fracturing and/or vugular development is also noted. The sample is then placed in a pressure cell and the air evacuated with a high speed vacuum pump. This evacuation is continued only long enough to reduce the pressure to approximately the vapor pressure of water in order not to remove excessive amounts of water. Water is admitted to the cell and allowed to penetrate the sample under atmospheric pressure, filling the pore space initially occupied by air and replacing the small amount of water removed by evacuation. Pressure up to 200 psi is applied to force water into the smaller capillaries, and the sample is left sub-

Jan 1, 1950

On August 22, 1966, just 20 months after writing sales agreements with Japanese steel mills, Hamersley Iron Pty Ltd made its first contractual shipment of 52,000 tons to Yawata Iron and Steel Co Ltd. As world news, the event was not spectacular. But to mining men it represented an astonishing achievement. Twenty months of feverish effort and the expenditure of more than $100 million had created a large open-pit iron ore mine, a crushing plant, storage and load-out facilities for sized ore, and a supporting township at Mt Tom Price; a 182-mile standard gauge railway; and port and loading facilities for a nominal loading capacity of 6000 tph as well as a port town, Dampier, on King Bay. The project was executed in the sparsely inhabited, arid, dissected-plateau country of the Hamersley Range in the northwest sector of Western Australia. Hamersley, 60% owned by Conzinc RioTinto of Australia Pty Ltd and 40% by Kaiser Steel Corp, holds sale contracts for ore and pellets valued at $770 million. The main contracts are with the Japanese, who are to be supplied with 65.5 million tons of ore during the 16 years from August 1966 to August 1982 and 18 million tons of pellets over a 10-yr period beginning in early 1968. Of lesser importance at this time, but presaging trends, are contracts for a total of nearly 1.5 million tons to be shipped to England and Western Europe during the years 1966-68. A pellet plant with a capacity of 2 million tpy is now under construction at Dampier and is to be on stream early next year. Another interesting project for which the plans are set, is a desalination plant for sea water to supply industrial requirements and potable water for the town of Dampier.

Jan 5, 1967

By Carl R. Christiansen

Since the first pay hole in Missouri's "New Lead Belt" was drilled in 1955, this district has become one of the world's leading sources of lead. The belt extends from north of Viburnum in a southerly direction to near Eminence, a distance of about 35 miles. The St. Joseph Lead Company was the discoverer and first to develop new mines in the Viburnum area. Since the discovery of the New Lead Belt, many companies have engaged in exploration programs and several major companies have become active in development of new mines. These include Cominco American, Inc., which operates a joint venture with Dresser Industries; Ozark Lead Company, a subsidiary of Kennecott Copper Company; and Missouri Lead Operating Company, a joint venture of Arnax and Homestake. St. Joseph Lead Company, with over 100 years of experience in the Old Lead Belt, has served as a leader in development of equipment and mining techniques, making its properties some of the most efficient mining operations in the world. The new producers give the district the benefit of fresh viewpoints, as their engineers are mostly from outside of Missouri and their previous experience has been considerably different from conventional lead belt practices. While all operations are similar in that they are room-and-pillar, the diverse experience of the operators has produced a group of mines that employ a variety of equipment and mining techniques to give increased efficiency

Jan 1, 1970

By F. Pošepný

Part I.—General Facts and Theories. PAGE 1. Systems of Classification Employed Hitherto, . . 199 2. Standpoint and View of the Present Paper, . . . 206 3. The Xenogenites in General, ...207 4. The Subterranean Water-Oirculation, . . . 212 A. The Vadose Underground Circulation, . . . 213 Filling of Open Spaces Formed by Vadose Circulation, . . 217 B. The Deep Underground Circulation, . 220 Ascending Waters Encountered in Mines, , 222 Related Phenomena near the Surface, . 225 Mineral Springs at the Surface,. . 230 Chemical Constitution of Mineral Waters, . 232 Minute Metallic Admixtures in Mineral Waters, . . . 238 Alterations Produced by Mineral Springs, . 240 Structural Features of the Deposits of Mineral Springs, . . 244 5. Origin of Ore-Deposits in the Deep Region, . . . 247 Manner of Filling of Open Spaces in General, . . . 254 Part II.—Examples or Classes of Deposits. 1. Ore-Deposits in Spaces of Discission, .. 264 General Features and Illustrations, a. Ore-Veins in Stratified Rocks, .. 269 Clausthal, 269; Andreasberg, 270. b. Ore-veins in the Neighborhood of Eruptive Masses, 271 The Erzgebirge, 271; Przibram, 272. c. Ore-Veins Wholly Within Large Eruptive Formations, 274 Hungary, 274; Dacian Gold-field. 275; Verespatak, 276; Vulkoj, 276 ; Comstock lode, 278.

Jan 1, 1894

By E. R. Morgan, J. C. Shyne, V. F. Zackay

NITROGEN used as an alloying element in steel has received increased attention in recent years. Its merit as an austenite stabilizer and hot strengthener has long been recojinized, particularly by European investigators.' Recent work' indicates that nitrogen contents of 1/2 pet or more allow the addition of several percent of ferrite-forming hot strengtheners, such as molybdenum, without subsequent austenite decomposition at elevated temperatures. The room temperature properties of such alloys are characterized by high yield and tensile strengths with excellent ductility, even after cold working, as shown in Tables I and 11. The 1350°F creep-rupture properties of Cr-Mn-Mo-N steels are comparable to those of commercial alloys such as Timken's 16-25-6, containing 16 pct Cr, 25 pct Ni, and 6 pct Mo, as shown in Table 111. Cr-Mn steel containing 1/2 pet N must be made under pressure if ingot gassing is to be avoided. However, there are difficulties attendant to this practice. Pressure melting restricts the ingot size, and the equipment required is costlier and more complicated than comparable air melting facilities. An effort was made, therefore, to determine more economical methods of adding nitrogen. The pressures generated in centrifugal casting usually range from 5 to 10 atm and are sufficient to prevent the gassing of high nitrogen Cr-Mn steels. A centrifugal casting was made of an alloy containing 16 pct Cr, 18 pct Mn, 2 pct Mo, and 0.73 pct N. A risk, 8 in. diam and 11/2 in. thick, was cast at 1000 rpm. It has been calculated that a pressure of 9 atm was developed at the periphery of the disk at this speed. Metallographic inspection of specimens taken from the disk revealed no gas holes or other defects. The elevated temperature properties of radial and circumferential specimens taken from this casting are given in Table IV. The creep-rupture life of this cast nickel-free austenitic steel was equivalent to that of the wrought Cr-Mn-Mo-N steels. Although centrifugal casting appears to lend itself to the manufacture of high nitrogen austenitic steels, its applicability is limited to relatively small sizes. A process applicable to the production of large ingots of high nitrogen steels is suggested by low carbon rimming steel practice. Gas holes formed during ingot solidification are not detrimental so long as they weld shut during hot rolling. An economic advantage of gassing ingots is the increased ingot-to-slab yield, especially if the ingots are mechanically capped. Also, it is probable that higher nitrogen levels can be achieved with mechanically capped ingots than with hot-topped ingots. A series of gassy heats was made under both atmospheric and higher pressures, as indicated in Table V. Several of the air melted ingots were mechanically capped by chilling the molten ingot tops with a steel plate. The ingots were allowed to freeze in steel molds without hot-tops unless otherwise indicated. A comparison of Table 111 with Table V shows no significant difference in the creep-rupture properties of the gassy and the nongassy ingots after hot work- ing nor between the gassy ingots produced under different conditions. References 1 F. Rapatz: Application of Stainless and Heat Resisting Steels Alloyed with Nitrogen. Sinhl and Eisen ( 1941) 61, pp. 1073-1078. 'V. I?. Zackay, J. F. Carlson, and P. L. Jackson: High Nitrogen Austenltlc Cr-Mn Steels. Trans. ASM 119551 48, PP. 509-523.

Jan 1, 1957

By F. S. Young, K. E. Gray

Drilling tests with a 11/4-in. diameter roller bit were performed on Berea and Bandera sandstones and Leuders limestone using water and two conventional drilling muds as circulating fluids to evaluate the influence of dynamic filtration on penetration rate. The muds possessed widely differing API fluid-loss properties. Mud filtrate was constrained to flow beneath the bit; no filtrate flowed radially through the borehole wall. Rock pore pressure at three different locations ahead of the bit, cumulative filtrate volume, borehole pressure and bit location were monitored during drilling. The rock samples, cored in three orientations with respect to bedding planes, possessed a wide range of liquid permeabilities. and were drilled at borehole-to-formation pressure differentials of 0, 250, 500 and 1,000 psig. The effect on penetration rate of API fluid loss, borehole pressure and rock permeability was studied. Rock permeability damage and pore pressure gradients beneath the bit were evaluated. The importance of borehole-to-formation pressure differential was illustrated for each drilling fluid and rock permeability combination. Penetration rates decreased with increased borehole pressure and reduced fluid loss. The observed penetration rate reduction due to changing fluid Ioss was attributed to decreased filtrate flow and improved mud cake plastering hy the low fluid-loss mud. The reduction in filtrate flow could not be related to spurt-loss phenomena. Rock permeability influences penetration rate through particle invasion ahead of the hit, which damage leads to high pressure gradients. Penetration rate variance with sample orientation was evident for water-drZled samples but less obvious for mud-drilled rocks. Permeability damage beneath the bit ranged from 1 to 3 cm. Maximum damage occurred in the first 0.1 cm. Pressure gradients varied with API fluid 10.s.s and could be correlated with penetration rate. The pressure gradient was found to influence penetration rare in rocks of all permeabilities tested. INTRODUCTION Early microbit and small-scale drilling experiments proved to be invaluable contributions to understanding the mechanics of drilling at depth. For example, the effect of borehole-to-pore pressure differential on drilling rate was demonstrated conclusively by Murray and Cunningham', Eckel' and others .' However, the effects of various drilling fluid properties on drilling rate, particularly filtration, have not been studied extensively on a laboratory basis. Microbit correlations of penetration rate with different viscosity and API fluid-loss muds led EckelV o conclude that viscosity and density. more than API fluid loss, were the most important fluid properties in controlling drill bit penetration rates. Ferguson and Klotz6 studied filtration beneath the bit and stated that the maximum amount of filtrate which could conceivably flow beneath a drilling bit could be described by a potential function associated with flow from a moving disc source. and be characterized by a depth-of-filtrate invasion. Invasion depth is a function of penetration rate, formation porosity and permeability, flooding efficiency, pressure difference between borehole and formation and borehole radius, assuming that no filtrate flows through the borehole walls. Electric analog and experimental measurements were obtained, assuming no plugging of the formation pores. Theoretically, filtrate invasion was predicted to extend from 1- to 15-hole radii beneath the cutting surface; experimental results indicated that the extent of invasion was only Y2 in. Comparing these data with results of core-plugging experiments by Norwak and Krueger' led Ferguson and Klotz to state that the drilling operation apparently contributes to higher filtration rates than are observed in nondrilling core filtration tests in which the core face is jetted and scraped. Glenn and Slusser: in describing a linear filtering system in which a rotating bit continuously scraped mud cake from the surface but did not penetrate Alundum cores, stated that mud-solids invasion and permeability damage of the cores were most severe in the first 2 to 3 cm. The filtrate flow rate through the core was found to stabilize after sufficient time had elapsed for the formation of an internal mud cake whose effective permeability was estimated to be 50 to 300 times as high as that of bulk filter cake. Krueger and Vogel reported core permeability damage depths up to 12 in. during a 5-day exposure period in which filter cake buildup was prevented. Havenaar pointed out that the discrepancy between reported and calculated values of filtrate volume obtained in the experiments of Ferguson and Klotz was due, among other things, to failure of the reported API fluid loss to truly represent filtration beneath the bit. Williams," Pro-koplz and others"" have shown that dynamic filtration tests (where a flow of fluid parallel to the filter surface continually erodes the deposited filter cake until a dynamic equilibrium between wall-shearing forces and normally directed compaction forces is attained) yield higher filtration rates than do static tests. Cunningham and Goinss reported results of drilling tests in impermeable shales. They found that by reducing

By G. L. Oldright, Henry de Rycker, S. F. Ravitz

The upper limit of richness of concentrates that can be smelted by means of the blast furnace without added diluents is fixed by the operation of sintering. A sinter feed with normal gangue constituents, containing more than about 50 per cent of lead, tends to fuse; as a result, air does not come sufficiently into contact with the sulphides at roasting temperatures, and sulphur elimination is poor. Since most lead concentrates now contain 55 to 80 per cent lead, it is necessary to add diluents to lower the grade of such sinter feed to about 50 per cent or less. This not only entails the expense of providing barren diluents when adequate diluents containing precious metals are not available but also appreciably lowers the capacity of the blast furnace to produce lead and increases slag losses. Attempts to desulphurize rich lead concentrates by methods other than sintering have not proved successful. Flash roasting, for example, converts much of the lead sulphide to lead sulphate rather than to oxide. However, this suggested the possibility that deliberate flash roasting of the concentrates to sulphate, followed by sinter roasting of the resulting product, might prove promising, particularly inasmuch as the elimination of sulphur from lead sulphate requires heat alone and not contact with atmospheric oxygen. The sintering of lead sulphate products has additional interest because important amounts of such products are now treated by lead smelters. Considerable quantities of lead sulphate are present in rich lead flue dusts and other by-products; lead-chamber sulphuric acid plants and other

Jan 1, 1944

By J. W. Furness

Before attempting any discussion of the importance of tariff enactments as applied to exhaustible resources, certain basic factors should be emphasized. First, it must be remembered that minerals differ from organic substances in that they are irreplaceable, and when once taken from the earth's crust enter into uses which ultimately dissipate them, so . that they cannot be recovered for future use. A second factor entering into the problem is the unequal distribution of the mineral deposits of the world. No industrial nation has within its political confines a sufficient quantity of all the minerals necessary for the maintenance and advancement of present civilization; hence international exchange of these commodities is inevitable. As minerals are essential to modern industry, the supply available to any given nation constitutes a factor which limits its ambition to advance industrially. A nation which has this ambition endeavors to secure not only a supply of minerals sufficient for its current needs, but also sources which will assure it expansion. Should mineral raw materials be withheld from such a nation by enactment, it seems inevitable that every effort will be made to obtain them, and that, should the nation deem itself sufficiently powerful, its ultimate recourse will be force. Thus the importance of tariff enactments, not only from the standpoint of industrial prosperity but from the standpoint of international peace, can be appreciated.

Jan 1, 1932

By John E. Latz

QUICKSAND far below the surface, stopped two attempts by the Potash Co. of America to sink a third shaft to a potash bed that lies 1000 ft below the southern New Mexico desert. Virtually all methods of grouting were employed in the two failures without any indication of consolidation of the flowing sand. Sinking the South Shaft at the Carlsbad potash mine seemed an almost insurmountable task, until freezing was employed as a final resort. This process that proved to be the answer may be defined as "the sinking of a shaft by freezing, consists of the formation, in the water-bearing strata, of a large block of frozen ground in which it is possible to sink a shaft without danger of an influx of water, providing the ice-wall between the water outside and the shaft itself is strong enough to resist the hydrostatic pressure." Freezing Method Used Extensively in Europe Successful frozen ground shaft sinking projects had been completed in Europe, and Russel G. Haworth, resident manager of the Potash Co. of America, went abroad in search of the know-how needed for the New Mexico undertaking. The freezing process, with a history of two failures at the time, was first successfully employed by Poetsch in 1885 at the Houssu Collieries near Haine St. Pierre, Belgium. Poetsch contracted to sink the remaining 64 ft of an uncompleted shaft through water laden strata from a depth of 190 ft to a depth of 254 ft. This work was in progress until 1887. The freezing and sinking consumed more than two years. As a result of early failures, the process was not favorably received until soon after the turn of the century. The accurate prediction of success in a given application was made possible by the concerted effort and study of a group of European engineers. Means of accurate deviation measurement and control were devised, the nature and properties of frozen water laden soil (the ice wall) were investigated, a thorough and rational basis of refrigeration load calculation developed, and concurrently the efficiency and dependability of refrigeration machinery was greatly advanced. Numerous shafts in Germany, Belgium, France, and England today testify to the reliability and economical surety of the freezing method. Applied to the South Shaft, which is circular in cross-section and 15-ft diam, the freezing method consisted of drilling holes 350-ft deep, through the water bearing strata into impervious ground-the freeze hole pattern being concentric with the shaft and 31-ft diam. The holes were cased with pipe closed on the bottom end. Smaller tubes were placed inside these casings and connected to a header supplying chilled brine from a refrigeration plant. The brine descended in the tubing to the bottom of the hole and ascended through the annular space between the two pipes to the top of the casing; flowed into the return header and back to the refrigeration plant. Under these conditions, each of the freeze hole casings became surrounded by a cylinder of ice

Jan 1, 1952