Search Documents

By H. W. Ahrenholz

Seven weeks of 1971 were devoted to a nationwide coal walkout resulting in lost production of some 70 million tons and leaving 1971 coal production at about 550 million tons. Compounding the problem, consumption of coal in 1971 by electric utilities rose by about 5% to 336 million tons. In the mean- time, numerous contracts were awarded for coal R&D including $24.8 million given by the Office of Coal Research to Bituminous Coal Research for the construction of a coal-to-gas pilot plant using the BIGAS process. Exports declined mainly due to Japan's decrease in steel production and to that country's increase in coal imports from Canada and Australia. The advances in equipment design and mining procedures made 1971 a noteworthy year. Introduction of the variable pitch I dipper, the trend toward wheeled vehicles, the greater use of scrapers in reclamation and battery-operated vehicles and oscil-mining, and the increased activity in the areas of ventilation and dust control were given widespread approval. There were also strides made in computerization, longwall mining, roof bolting, rock dusting, mine haulage and methane detection.

Jan 2, 1972

By Charles H. Moore

When lime and magnesia are used as fluxes in the smelting of titaniferous ores fluid, digestible slags low in iron oxide and high in titanium dioxide are produced. The mineral phases present in such slags are (Fe,Mg)O.2TiO2, CaTiO3, and minor amounts of silicate glass (or its devitrification products). The flux additions are added to the ore in relative amounts to crystallize a ratio of (Fe,Mg)O.2TiO2 to CaTiO2, of near the eutectic proportions of 60 pct (Fe,Mg)0.2TiO2 and 40 pct CaTiO3. FeO-Ti02 (ilmenite) remains present in the slag until the FeO content is reduced to approximately 8 pct. Op- timum slag composition is obtained by reducing the FeO content to between 2 and 6 pct. Continued reduction shifts he (Fe,Mg) 0.2Ti02 to oxygen deficient structures classified as MgTi30e and MgTi204. Further reduction yields titanium oxycarbides and freezes the melts.

Jan 1, 1949

By E. O. Jones

DURING the heating of cold-worked nickel silver, the tendency of the material to crack is well known. The present research deals with this question, and may conveniently be divided into the following sections: Changes in these alloys during heating and cooling, determination of the temperature at which cracking occurs, effect of grain size, quenching cracks, methods of overcoming annealing cracking. The work is far from complete, in particular the influence of impurities on this tendency has not been investigated, but the results so far obtained lead to certain definite conclusions, which are of theoretical and practical importance. CHANGES IN ALLOYS DURING HEATING AND COOLING During the annealing of many metals at a temperature just below that at which recrystallization sets in, there is evidence of some change, the effect of which is to harden and embrittle the material. This effect has been most clearly demonstrated in the cases of aluminum, copper, brass, and nickel silver, and appears to be a common property of cold-worked metals and alloys, or, at any rate, the non-ferrous ones. The effect would obviously offer an explanation for certain types of annealing cracking, but the trouble is so much more common in the nickel silvers than in the other alloys that some special cause should be looked for. There is, however, fairly good reason for believing that similar cracking may occur in some of the brasses; D. Bunting suggests that the a brasses toward the saturation limit are subject to a transformation closely allied in nature to that known to occur in the nickel silvers at around 320° C. Although the existence of this critical temperature range was known, it did not necessarily follow that this transformation was responsible for the trouble under investigation, so the first portion of this paper deals with the attempts made to determine whether other critical changes might not occur in these alloys. There were already reasons for the belief that such would prove to be the case, as the mechanical properties of the nickel

Jan 7, 1925

By Thomas R. Mager

An in.t!estigation has been made of the equilibrium conditions at 1200°C in the reaction between hydrogen sulfide gas and sulfur dissolved in Fe-Si alloys From this the equilibrium constant, activity coefficient, and activity of sulfur in solution were calculated. A number of studies of the equilibrium of sulfur with iron and iron alloys have given closely agreeing results from which the activity and free energy of the dissolved sulfur may be found. Sherman, El-vander, and chipman1 discussed the significant researches of dilute solutions of sulfur in liquid iron prior to 1950, and the results of this study indicated that the relationship between the ratio of PH2S/PH2 in the environment and the percentage of sulfur in solution is not a linear one. Morris and williams2 studied the equilibrium conditions in the reaction between hydrogen sulfide gas and sulfur dissolved in liquid iron and Fe-Si alloys, and reported that silicon dissolved in iron has a pronounced effect on the equilibrium conditions. They found that the activity of sulfur in iron is increased by the addition of silicon. At a silicon content of 4 pet the activity coefficient of sulfur was about twice that for sulfur dissolved in pure iron. Sherman and chipman3 investigated the chemical behavior of sulfur in liquid iron at 1600°C through the study of the equilibrium: H2 + S = H2S; K = PH2S/PH2 . 1/as [1] From the known equilibrium constant of the reaction between H2, H2S, and S and the experimental data, the activity of sulfur in the melt was determined. They found that the activity coefficient of sulfur defined as fs = as/%s is increased by silicon and decreased by manganese. Morris4 and Turkdogan5 also reported that manganese decreases the activity coefficient of sulfur in liquid iron and iron-base alloys. A recent technique of sulfur analysis developed by Kriege and wolfe6 of the Westinghouse Research Laboratories permits an accurate sulfur analysis of 0.5 * 0.2 ppm in the range of 0.1 to 3 ppm, whereas in the range of 3 to 50 ppm the accuracy is ±1 ppm. This technique of sulfur analysis was utilized in this experiment. Previous unpublished data reported that sulfur analysis by the combustion technique was not accurate below 20 ppm. EXPERIMENTAL PROCEDURE Five 5-lb ingots of high-purity Fe-Si were prepared. Three of these ingots were prepared without the addition of manganese but with a variation of silicon contents from 2 to 4 pet. The remaining two ingots contained 3 pet Si with the addition of manganese. Ingots were made at each of three silicon levels: 2, 3, and 4 pet. No alloys were made with less than 2 pet Si since below approximately 1.8 pet Si the binary alloy exhibits a to ? transformation. The two additional ingots of 3 pet Si-Fe were made at each of two manganese levels: 0.20 and 0.50 pet. To minimize the effects, if any, of impurities on the activity of sulfur on Si-Fe, the best metals available were used for melting. All ingots were vacuum-melted in magnesium oxide crucibles. After obtaining samples for chemical analyses, the ingots were processed. This consisted of hot rolling and subsequently cold rolling the alloys. Each ingot was hot-rolled at 1000°C, reheating between every pass to minimize grain growth. All heating was done in a protective argon atmosphere. The slabs were hot-rolled to strips 50 mils thick. After hot rolling, all the material was pickled to remove the scale formed on the surface of the strip during hot rolling. The material was then cold-rolled to 12-mil strips. Single strips of the material used in this experiment were hydrogen-annealed at 1200°C for 16 hr in an alumina tube. Chemical analyses of strips M-1, M-3, M-4, M-7, and M-8 are given in Table I. Sulfur, silicon, and manganese analyses were made from the millings from the cold-rolled 12-mil strips. The oxygen analyses were made from slugs of the as-cast material. The hydrogen sulfide used in these experiments was supplied from cylinders containing a mixture of argon and 1 pet hydrogen sulfide. The parts per million of hydrogen sulfide were determined from the analysis of the exit gas of the annealing furnace during each anneal. The flow rate of hydrogen was approximately 1 liter per min in all anneals. The

Jan 1, 1964

By Gail F. Moulton

In spite of an increase of 7 cents per barrel in the posted price of oil for the Panhandle field effective June 16, 1943, there was less drilling during 1943 than ir, any of the several previous years. The drilling statistics are compiled as Table 2 and show the material increase in the percentage of the total number of field wells completed as dry holes. This increase suggests that the productive area of the field is largely drilled up on the well-spacing pattern now followed and that new discoveries will be required to permit any important new activity in the area. The fact that only four wildcats were drilled in the area during the year indicates that some new prospecting technique or some ncw point of view is required to stimulate exploration. No new producing areas were discovered during 1943 and no additions to oil reserves were made through extensions or discovery 'of new pays. Accordingly, the proven reserves in the area declined by the amount of the production, or nearly 31 million barrels. These results of drilling are similar to those obtained during 1942, whcn no new oil areas were discovered as a result of wild-catting, a total of five wildcat wells in 1942 resulting in four failures and one gas-fieid discovery of undetermined merit. sion. The number of oil-producing wells reported by the Commission increased during the year by 163 to a total of 5576 as of December.

Jan 1, 1944

By Gail F. Moulton

In spite of an increase of 7 cents per barrel in the posted price of oil for the Panhandle field effective June 16, 1943, there was less drilling during 1943 than ir, any of the several previous years. The drilling statistics are compiled as Table 2 and show the material increase in the percentage of the total number of field wells completed as dry holes. This increase suggests that the productive area of the field is largely drilled up on the well-spacing pattern now followed and that new discoveries will be required to permit any important new activity in the area. The fact that only four wildcats were drilled in the area during the year indicates that some new prospecting technique or some ncw point of view is required to stimulate exploration. No new producing areas were discovered during 1943 and no additions to oil reserves were made through extensions or discovery 'of new pays. Accordingly, the proven reserves in the area declined by the amount of the production, or nearly 31 million barrels. These results of drilling are similar to those obtained during 1942, whcn no new oil areas were discovered as a result of wild-catting, a total of five wildcat wells in 1942 resulting in four failures and one gas-fieid discovery of undetermined merit. sion. The number of oil-producing wells reported by the Commission increased during the year by 163 to a total of 5576 as of December.

Jan 1, 1944

By O. Mellgren, A. M. Gaudin, P. L. De Bruyn

The adsorption density of ethyl xanthate on pyrite was determined as a function of xanthate concentration. Surface preparation of the mineral appears to have asafunctionsome effect on the subsequent adsorption process, A monolayer of xanthate on the surface is exceeded only in presence of oxygen. The effect of OH- , HS- (and x and CN- S=)and on the amount of xanthate adsorbed was investigated. Competition between OH- and X- (xanthate) ions for specific adsorption sites is indicated over a wide pH range. IN the flotation of sulfide ores, xanthates are most commonly used to prepare the surface of the mineral to be floated so that attachment to air takes place. The quantity of agent required to make the mineral hydrophobic is usually very small, of the order of 0.1 to 0.25 lb per ton of mineral. Details of the mechanism of pyrite collection are for the most part unsettled. Adsorption of collector has long been believed to involve an ion exchange mechanism as demonstrated for galena' and for chalcocite.2 In the work on chal-cocite it was also demonstrated that a film of xanthate radicals unleachable in solvents that dissolve alkali xanthates, copper xanthate, or dixanthogen was formed at the surface of the mineral. The unleachable product increased with increasing addition of xanthate up to a maximum corresponding to an oriented monolayer of xanthate radicals. Pyrite is extremely floatable with xanthate if its surface is fresh.9 ut the floatability decreases rapidly as oxide coatings increase in abundance. Pyrite shows zero contact angle when in contact with ethyl xanthate solution at pH higher than about 10.5;4 at neutrality, a contact angle of 60" is obtained at a reagent concentration of 25 mg per liter. Alkali sulfides and cyanides are pyrite depressants. In this study of pyrite collection the writers have sought to relate measured xanthate adsorption to the method used in preparing pyrite, to the presence or absence of oxygen, to concentration of hydroxyl, hydrosulfide, sulfide, and cyanide ions. The principal experimental tool has been radioanalysis," " using xanthatcx marked with sulfur 35. Experimental Materials Pyrite: Unlike most sulfides, pyrite is a poly-sulfide. The structure given by Bragg7 resembles that of sodium chloride, the iron atoms corresponding to the position of sodium and pairs of sulfur atoms corresponding to the position of chlorine. The edge of the unit cell in pyrite is 5.40 A and in halite 5.63 A. The S-S distance in pyrite is 2.10 A; the Fe-S distance, 3.50 A: and the Fe-Fe distance, 3.82 A. Natural pyrite from Park City, Utah, was used in this investigation. Pyrite 1 was obtained by hand picking pure crystals. Pyrite 2 and Pyrite 3 were obtained from finer textured crystalline material containing inclusions of silicates. The same cleaning technique was utilized for the preparation of Pyrite 2 and Pyrite 3, whereas a different cleaning technique was used for Pyrite 1. Pyrite 1 was prepared as follows: The crystals were ground in a porcelain ball mill and the 200/400 mesh fraction was separated by wet screening with distilled water, followed by washing for 1 hr with deoxygenated distilled water acidified with sulfuric acid to pH 1.5. The acid was removed by rinsing with deoxygenated distilled water on a filter until a pH of 6.0 was reached in the effluent. This filtration was carried out under nitrogen. The sample was then dried in a desiccator under nitrogen. The period of time for which this pyrite sample was in contact with water containing oxygen was about 4 hr. The specific surface as determined by the BET gas adsorption method was 582 cm2 per g. Final material assayed 53.12 pct sulfur and 46.5 pct iron (theoretical, for FeS,: S, 53.45 pct; Fe, 46.55 pct). After crushing, Pyrite 2 and Pyrite 3 were washed with 1 M HCl. rinsed, and fed to a laboratory shakinq table to remove the small amount of silicates. The concentrate obtained was ground in a laboratory steel ball mill. The 200/400 mesh fraction was separated by classification in a Richards hindered settling tube. This fraction was then given a final wash with 0.1 M HCl and deoxygenated water was filtered through the sample. The final effluent showed a conductivity equivalent to that of a solution having a salt concentration of 0.3 ppm. Aqueous hydrogen sulfide solution was then added to the sampln (about 100 ml saturated H,S solution to about 1000 g pyrite under a few hundred milliliters of water) which was stored wet under nitrogen. The sample stored in this manner showed no indication of formation of iron oxides, whereas iron oxides appeared

Jan 1, 1957

By N. D. Shutler

This paper describes a numerical mathematical model of the steamflood process that depends on fewer restrictive assumptions than models previously reported. The solution, however, is obtained economically. Example calculations are presented that, on comparison with experimental results, tend to validate the model. Results that expose certain process mechanics are discussed. The model describes the simultaneous flow of three phases — oil, water and gas — in one dimension. It includes the effects of three-phase relative permeabilities, capillary pressure, and temperature- and pressure - dependent fluid properties. Interphase mass transfer of water-steam is allowed, but the oil is assumed nonvolatile and the hydrocarbon gas insoluble in the liquid phases. The model allows heat convection in one dimension and two-dimensional heat conduction in a vertical cross-section spanning the oil sand and adjacent strata. The hydrocarbon-steam gas composition is tracked, but the effect of gas composition on water-steam phase behavior is neglected. The model is solved numerically in three separate stages. The three-phase mass balances are solved simultaneously using Newtonian iteration on nonlinearities occurring in the accumulation terms. The energy balance is solved separately by noniterative application of the alternating-direction implicit procedure. Separate solution of the composition balance is accomplished by straightforward solution of the finite difference equations. The method of effecting nonsimultaneous, stable solution of the mass and energy balances is the key to the success of the model. INTRODUCTION Mathematical tools as well as laboratory and field experiments are necessary to help us understand the complex steamflood process. A mathematical model can expose process mechanics and show the relative importance of process variables, but this ability is often limited by restrictive assumptions. Most known models of steam processes,l-5 with the exception of the model of Gottfried,6 are "simplified" in that they involve analytic approximations and require many restrictive assumptions. The primary utility of these methods lies in the routine use as an aid in engineering design. By contrast, the comprehensive model presented here is numerical and requires far fewer restrictive assumptions. It finds its primary utility as a research tool. It serves as an aid in understanding the nature of the process, in interpreting laboratory experiments and in evaluating and developing simpler mathematical models for engineering design. The major reason why previously presented models have been confined to the "simplified" class is evidenced by the one published exception. In 1965, Gottfried6 presented a numerical model for the combustion process of which the steam process is a subset. The result is a comprehensive tool (though it neglects capillarity and two-dimensional heat conduction) that is troubled with convergence problems and that requires 2 to 3 hours of IBM 7094 time to complete a calculation. Though our present model does not simulate combustion, it does consider capillarity and two-dimensional heat conduction and it overcomes the convergence and computer-time problems. MATHEMATICAL DESCRIPTION OF STEAMFLOODING FLUID FLOW The equations employed to describe three-phase fluid flow are of a familiar form. Darcy's. law provides expressions for the velocities of the three phases (oil, water and gas), which, when combined with oil, water and gas mass balances, give the partial differential equations governing flow of the

Jan 1, 1970

Albin, B. R. Billings, Mont. 28 Amster, Nathan L 25 Broad St., New York, N. Y. '28 Bache, Jules S. 42 Broadway, New York, N. Y. 28 Barrett, C. P. 5338 Harper Ave., Chicago, 111. '28 Baum, Frank G., Cons. Hydro-Electric Engr Cassel, Shasta Co., Cal. '28 Bayless, William S. Russ Bldg., San Francisco, Cal. '28 Bean, Louis H.60 E. 42nd St., New York, N. Y. '28 Beatty, Roes J. 1105 First National Bank Bldg., Chicago, Ill. '28 Benwell, Oswald F. Hold Mags. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Blumenthal, Hugo 44 Pine St., New York, N. Y. '28 Boettcher, Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H. Iola, Kan. '28 Brown, Colvin B. Chamber of Commerce, Washington, D. C. '28 Bart, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1932

By E. O. Jones, E. Whitehead

During the heating of cold-worked nickel silver, the tendcncy of the material to crack is well known. The present research deals with this question, and may conveniently be divided into the following sections: Changes in these alloys during heating and cooling, determination of the temperature at which cracking occurs, effect of grain size, quenching cracks, methods of overcoming annealing cracking. The work is far from complete, in particular the influence of impurities on this tendency has not been investigated, but the results so far obtained lead to certain definite conclusions, which are of theoretical and practical importance. Changes in Alloys During Heating and Cooling During the annealing of many metals at a temperature just below that at which recrystallization sets in, there is evidence of some change, the effect of which is to harden and embrittle the material. This effect has been most clearly demonstrated in the cases of aluminum, copper, brass, and nickel silver, and appears to be a common property of cold-worked metals and alloys, or, at any rate, the non-ferrous ones. The effect would obviously offer an explanation for certain types of annealing cracking, but the trouble is so much more common in the nickel silvers than in the other alloys that some special cause should be looked for. There is, however, fairly good reason for believing that similar cracking may occur in some of the brasses; D. Bunting1 suggests that the a brasses toward the saturation limit are subject to a transformation closely allied in nature to that known to occur in the nickel silvers at around 320" C. Although the existence of this critical temperature range was known, it did not necessarily follow that this transformation was responsible for the trouble under investigation, so the first portion of this paper deals with the attempts made to determine whether other critical changes might not occur in these alloys. There were already reasons for the belief that such would prove to be the case, as the mechanical properties of the nickel

Jan 1, 1926

By G. Gutierrez, M. C. Fuerstenau, J. D. Miller

The response of pure goethite and two natural iron ores to flotation with potassium octyl hydroxamate is presented. The ores contained 12.5% and 39.7% iron; concentrates containing 69.5% and 61.5% iron, respectively, were obtained with additions of 0.4 lb/ton hydroxamate. Selective flotation of iron oxides from associated gangue minerals has proven difficult in the past with standard collectors, such as sulfonates and fatty acids. As a result, recent work has been directed toward silica flotation with calcium activation after the iron oxide surfaces have been blinded with certain starches.& The results obtained with this technique are encouraging. This method, however, involves depressing a mineral that would normally float under the conditions employed. A preferable method would involve floating the iron oxide because quartz is naturally depressed until activated. Earlier work involved this approach, but in view of the results obtained, collectors that exhibit greater specificity for iron are needed. During an investigation of chrysocolla flotation with potassium octyl hydroxamate, a metal chelate former, it was observed that pyrite floated well with low additions of collector.3 This phenomenon suggests that hydroxamate has a rather strong affinity for iron, and that other iron-bearing minerals should also respond to flotation with octyl hydroxamate. The object of this paper is to determine this response. The experimental work was divided into areas, the first of which involved microflotation experiments with pure goethite with an apparatus described previously.4 Goethite was selected because of the ease

Jan 1, 1968

By T. A. Simpson

The search for ore continued at its relentless pace throughout 1967. Canada, South Africa and Australia plus a few scattered localities on the globe reported minerals finds of significant importance. Many of the reported finds were not high grade ore, but they nonetheless will assist in sup- plying a highly industrialized, mineral hungry world. No longer does inaccessibility and remoteness close an area to mineral exploration and development. The communication and transportation systems of today have closed the gap and, moreover, the demand for essential mineral commodities is causing price shifts which encourage exploitation of deposits heretofore considered uneconomical.

Jan 2, 1968

By W. C. Leslie

The textures of cold-rolled and of annealed iron are compared with those of an iron-0.8 pct copper alloy in which the amount of precipitation after cold rolling was controlled. Previously published pole figures -for cold-rolled and for annealed iron are confirmed. The effects of precipztatiotz after cold rolling are to retain the cold-rolled texture after annealing, to inhibit the formation of the usual allnealing texture, and to produce elongated recrys-tallized ferrite grains. It is suggested that the inhibition of new textures by precipitation after cold rolling is a general phenomenon. A great deal of attention has been paid to the development of texture during the secondary or tertiary recrystallization of ferritic alloys, but very little work seems to have been done on the control of texture during primary recrystallization. If such control were attained, it might be possible to simplify the processing of oriented materials or to change the characteristics of current cold-rolled and an-nealed products. From previous experience, it seemed likely that texture could be controlled by recrystallizing a supersaturated solid solution. Green, Liebmann, and Yoshidal found that the formation of preferred orientation in aluminum (40 deg rotation about <111> relative to the deformed matrix) was inhibited when iron was retained in supersaturated solid solution in the strained aluminum. The authors attributed this inhibition to iron atoms in solid solution. There is, however, an alternative explanation. Green et al, took a highly supersaturated solution of iron in strained aluminum and heated it to an unspecified temperature for recrystallization. It is probable that precipitation occurred prior to and during recrystallization, and it is proposed that the inhibiting agent is this precipitate, rather than the iron atoms in solid solution. It is important to note that precipitation before cold work is ineffective; the effective precipitate is that formed after cold working and either before or during recrystallization. The location and distribution of the precipitate are critical. Precipitation in such a manner has been found to have profound effects upon kinetics of recrystallization and the microstruc-ture of the recrystallized alloys.2-4 It would be surprising, indeed, if this were accomplished with no change in texture. Because of the relative simplicity of the system, and because of previous experience,4-7 it was decided to determine the effect of precipitation on texture in an alloy of iron and copper. Bush and Lindsay5 found an unspecified change in texture in cold-rolled and annealed low-carbon rimmed steel sheets when the copper content exceeded 0.1 pct. MATERIALS In earlier work, the rate of recrystallization of a low-carbon steel was greatly decreased by 0.80 pct copper, and, after the proper treatment, the recrystallized ferrite grains were greatly elongated.4 Accordingly, it was decided to investigate the effect of precipitation on texture at this level of copper content. The iron and the iron-copper alloy were made from high-quality electrolytic iron and OFHC copper, vacuum-melted in MgO crucibles, cast, hot-rolled to 0.2 in., then machined to 0.150 in. The compositions are given in Table I. The plates were heated to 925°C and brine quenched, twice. This produced a ferrite grain size of ASTM 0 in the iron and ASTM 1 in the Fe-Cu alloy. Disk specimens were cut from the heat-treated plates, repeatedly polished and etched, then used to determine (110) and (200) pole figures by reflection. Despite the complication of large grain size, these pole figures strongly indicated a random texture. PROCEDURES The copper content in solid solution in ferrite before cold rolling and recrystallization, and hence, the amount that could precipitate during the recrys-tallization anneal, was controlled at three levels by heat treatment. The specimens as quenched from 925° C were presumed to have all the copper, 0.80 pct, in solid solution. Other samples of the quenched alloy were aged 5 hr at 700°C to retain about 0.5 pct Cu in solid solution.6 A third set of quenched specimens was reheated to 700°C, then slowly cooled in steps, to reduce the amount of copper in solid solution to a very low level. All specimens were cold-rolled 90 pct, from 0.150 to 0.015 in. thick. The rolling was done in one direction only, i.e., the strip was not reversed between passes, with a jig on the table of the mill to keep the short specimens at 90 deg to the rolls. The rolls were 5 in. in diameter and speed was 35 ft. per min. Machine oil was used as a lubricant. In a supersaturated alloy, the maximum effect of the copper precipitate on microstructure and on recrystallization can be developed by a treatment at 500°C, after cold rolling and before recrystallization.&apos;

Jan 1, 1962

Meeting of May 22, 1914.-President Thayer. announced the appointment of the following Committee on Arrangements for the San Francisco meeting of 1915: Charles W. Merrill, Chairman; F. W. Bradley, Abbot A. Hanks, S. B. Christy, and H. C. Hoover. President Thayer announced the appointment of the following Committee on Organization for the Utah-Nevada Local Section: R. C. Gemmell, Chairman; C. D. Blood, Lafayette Hanchett, Ernest Gayford; Duncan MacVichie, and George W. Riter. The President of the Institute offered $100, to be known as the "President&apos;s Prize," to be used as prizes for the best papers submitted by members of the Affiliated Student Societies, to be divided as follows: First Prize, $50; Second Prize, $30; Third Prize, $20. A committee, consisting of J. F. Kemp, Chairman; W. L. Saunders, and T. T. Read, was appointed to report on the conditions to govern the award. The President announced the appointment of the Committee on Mining and Milling Methods, the personnel of which is shown on a subsequent page of this Bulletin. The following were appointed on the Advisory Committee to the U. S. Bureau of Standards, to represent the manufacture of the various non-ferrous metals as indicated: Copper, F. L. Antisell; Nickel, David H. Browne; Lead, H. O. Hofman; Aluminum, J. W. Richards; Zinc, G. C. Stone. It was voted to hold a meeting of the Institute under the auspices of, the Iron and Steel Committee, the Committee on Petroleum and Gas, and the Committee on Coal and Coke, in Pittsburg, Pa., Oct. 8, 9, and. 10, 1914.

Jan 7, 1914

By Elliot Rexford

The quality of aggregate materials is of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 3, 1950

By Robert Bakish

VARIOUS aspects of structure-sensitive corrosion of single crystals and polycrystalline aggregates of Cu,Au have been presented in papers by the author, in association with W. D. Robertson. Prompted by some observations in the course of these studies, a new approach to the problem was undertaken. Results of these new experiments are reported here. Thin slices, less than 2 mm thick, were prepared from single crystals 3.5 mm in diam grown by the Bridgman technique. The crystals were homogen- ized for 300 hr at 850°C. Crystals with no deformation, crystals deformed in tension to the yield point, and crystals deformed 20 pct in excess of the yield point were used. Crystals of several different orientations were studied. Slices were immersed for one month in 2 pct aqueous solution of FeCl3 and, subsequent to this immersion, were subjected to bending. Immersion and bending were carried out at room temperature. The size and geometry of the crystals did not permit accurate data on the loads involved. A most unexpected result was obtained in the process of bending these slices of Cu3Au crystals normal to the (110) plane. Completely brittle be-

Jan 1, 1958

By L. O. Howard

THE CHAIRMAN (WALTER DOUGLAS, New York, N. Y.).--I presume, gentlemen, that Mr. Howard&apos;s experience with the Great Falls basic-lined converter has been as regards the tonnage produced from a single lining, perhaps, a world&apos;s record. About 6 months ago Mr. Howard shut down and tore out what was left of the first basic-lining which was installed at the Old Dominion, the lining having produced something over 70,000,000 lb. of copper. This was due probably not only to the very excellent grade of the matte which was produced by the smelter there,

Jan 12, 1916

By J. J. Scott

During 1967 wage settlements and strikes ran at a high rate and it has been estimated that union gains of 4 ½ % to 5% per year have been attained in many instances. When these events are coupled with the need to operate on lower grade and deeper deposits the need for technological advances in underground mining becomes obvious. Emphasis has been on ways to reduce the number of manshifts required per ton of product. Most significant advances have been made in rapid advance of primary mine openings, development of mobile, rubber-tired, front-end loaders and hauling units, high-speed drilling with rotary and rotary percussive units and a serious look at nuclear devices to break large volumes of ore cheaply. Boring Developments in bit manufacture and metallurgy have allowed continuous boring-type machines to be used on harder formations than was deemed feasible in the past. Hecla Mining Co. has been using raise boring equipment for drilling 9 7/8 in. diam pilot holes in raises which are later reamed in an upward direction to 48 in. diam. The machine used is a J. S. Robbins model 42R raise borer which has been used successfully to drill two relatively long 48-in. diam holes. The first was 520 ft in length at a dip of 76º, and the second was a 785-ft vertical hole.

Jan 2, 1968

By R. J. Mellen

In a chloridizing roasting and cyanida-tion plant treating a manganese-silver ore, certain experiments pointed out the way to an improvement in roasting conditions by a change in the degree of crushing. The following short article is simply a description of the various changes that were necessary throughout the plant and of the results obtained. There is nothing unusual in these changes but they are of some interest in that they constitute a good many of the alterations usually resorted to in increasing production. In the beginning, the changes were brought about by an experiment that was not successful, but which clearly pointed to means of improving the operation, and is an example of the fact that often experimental work may result in failure and still be of value in arriving at correct fundamentals. This experiment also shows how far a metallurgist can get out of line in his deductions, particularly in a field with which he is not thoroughly familiar. The ore at the plant of Compania Minera Kildun y Anexas is crushed through a 13-in. gyratory, a 3-ft. standard Symons cone crusher and a set of 16 by 42-in. rolls, the latter in closed circuit with two Tyler type 400 screens. The crushed ore is then conveyed to two fine-ore bins. These provide storage and feed for two 6 by 90-ft. kiln roasters, which discharge directly to coolers. The coolers in turn discharge to a 6 by 12-ft. ball mill, where the ore is ground for cyanidation. Laboratory and pilot-plant tests previous to the mill construction had indicated that minus ¼-in. crushing was satisfactory for roasting, although results did not vary greatly with some coarser or considerably finer crushing. The plant was designed for a capacity of 300 tons per day on this basis. After a few months operation, the initial operating problems were overcome and the anticipated milling rate was reached but the results being obtained were not really good. The plant seemingly did not have much excess capacity in any department but the roasting operation was the most critically limiting factor both as to tonnage and the results obtained. If this could be improved there seemed some possibility of improving the total tonnage rate to some extent. Segregation of the calcine into various screen sizes showed that the coarser sizes were not giving the expected recoveries. In all of the laboratory and pilot-plant testing, any limiting conditions as to the percentage of salt used, temperatures, feed rates, etc., had affected the fine material more than it had the coarse, and even in making laboratory tests at this time the mill conditions could not be exactly duplicated. Further laboratory testing indicated that a segregation of the rushed Ore into a coarse and fine product for roasting might result in some improvement in roast-

Jan 1, 1947

By R. J. Mellen

In a chloridizing roasting and cyanida-tion plant treating a manganese-silver ore, certain experiments pointed out the way to an improvement in roasting conditions by a change in the degree of crushing. The following short article is simply a description of the various changes that were necessary throughout the plant and of the results obtained. There is nothing unusual in these changes but they are of some interest in that they constitute a good many of the alterations usually resorted to in increasing production. In the beginning, the changes were brought about by an experiment that was not successful, but which clearly pointed to means of improving the operation, and is an example of the fact that often experimental work may result in failure and still be of value in arriving at correct fundamentals. This experiment also shows how far a metallurgist can get out of line in his deductions, particularly in a field with which he is not thoroughly familiar. The ore at the plant of Compania Minera Kildun y Anexas is crushed through a 13-in. gyratory, a 3-ft. standard Symons cone crusher and a set of 16 by 42-in. rolls, the latter in closed circuit with two Tyler type 400 screens. The crushed ore is then conveyed to two fine-ore bins. These provide storage and feed for two 6 by 90-ft. kiln roasters, which discharge directly to coolers. The coolers in turn discharge to a 6 by 12-ft. ball mill, where the ore is ground for cyanidation. Laboratory and pilot-plant tests previous to the mill construction had indicated that minus ¼-in. crushing was satisfactory for roasting, although results did not vary greatly with some coarser or considerably finer crushing. The plant was designed for a capacity of 300 tons per day on this basis. After a few months operation, the initial operating problems were overcome and the anticipated milling rate was reached but the results being obtained were not really good. The plant seemingly did not have much excess capacity in any department but the roasting operation was the most critically limiting factor both as to tonnage and the results obtained. If this could be improved there seemed some possibility of improving the total tonnage rate to some extent. Segregation of the calcine into various screen sizes showed that the coarser sizes were not giving the expected recoveries. In all of the laboratory and pilot-plant testing, any limiting conditions as to the percentage of salt used, temperatures, feed rates, etc., had affected the fine material more than it had the coarse, and even in making laboratory tests at this time the mill conditions could not be exactly duplicated. Further laboratory testing indicated that a segregation of the rushed Ore into a coarse and fine product for roasting might result in some improvement in roast-

Jan 1, 1947