Search Documents

OFFICERS AND DIRECTORS (The Officers are the President, 6 Vice-Presidents, the Treasurer, and the Secretary) President and Director HENRY DEWITT SMITH' Past President and Director LEO F. REINARTZ President-elect and Director C. E REISTLE, JR

Jan 1, 1955

By F. V. Lenel

Resistance sintering under pressure is a method of hot pressing in which a powder compact is subjected to pressure and simultaneously heated by passing a low voltage high amperage current through it. Equipment for this process is described. Its basic characteristics such as resistance requirements for powders and compacts, temperature distribution in compacts, and gas reactions during resistance sintering are discussed. Examples of the sintering process in compacts made of a single metal or an alloy powder and in compacts made of mixtures of powders are presented. Potential commercial applications of the process are evaluated. THE usual sequence of operations in commercial powder metallurgy is to compact metal powders in a die at room temperature and sinter the compact subsequently without applying pressure while the compact is in the sintering furnaces. In hot pressing, on the other hand, the compacting and the sintering are combined. The loose powder, or in many cases a cold formed compact, is inserted into the die which is held at the hot pressing temperature, the compact is left in the die until it attains its temperature, and then pressure is applied and maintained for a given length of time. The die may be heated by surrounding it with a suitable furnace, by high frequency induction heating, or by passing current through the die. In hot pressing, compacts of high density and good mechanical properties can be produced in a relatively short time. One of the principal difficulties in hot pressing is the lack of suitable die materials which will have adequate strength at the hot pressing temperature. This difficulty can be overcome at least partially by heating only the material to be hot pressed without heating the die directly. This can be done by passing a low voltage high amperage current through the material and simultaneously subjecting it to pressure. Either loose powders or compacts can be hot pressed by this method in which the desired temperature is produced by the power dissipated in the metal powder. This method of hot pressing has been termed "electrical resistance sintering under pressure." The most significant differences between this operation and conventional hot pressing are: 1—The sintering times are very short, usually a fraction of a second and at most a few seconds. 2—The powder and die are initially cold. 3—Heat is generated within the powder itself and not conducted in from the die. 4— The pressure used is high. 5—Cooling following sintering is rapid, amounting to a quench. Resistance sintering of metal powders under pressure has been suggested repeatedly. In 1933, G. F. Taylor' proposed an apparatus which consisted of an insulating tube made of glass, or a ceramic filled with the powder to be pressed, and plungers above and below the powder. The powder was to be heated by passing an electric current through it and pressure was then applied. The apparatus was intended principally for hot pressing cemented carbides. Although the principle of resistance sintering under pressure is clearly shown in this patent, few details are given. A sintering period of a second or a fraction of a second, which is terminated by the operation of an inertia switch, is mentioned but no values for current density are mentioned. Low pressures, such as atmospheric pressure or a somewhat higher pressure exerted through a lever, are suggested. W. D. Jones' discussed electrical resistance sintering under pressure and proposed using resistance welding apparatus for this purpose. In a patent issued in 1944, G. D. Cremera described a method of electrical resistance sintering under pressure using resistance welding apparatus which was to be applied mostly to nonferrous metals such as copper, brass, bronze, and aluminum. Current densities of 400,000 amp per sq in., sintering times of 1 and 2 cycles of 60 cycle current, and pressures of 5 to 10 tsi are proposed. Cremer suggested using an

Jan 1, 1956

By W. B. Triplett, H. I. Aaronson, G. M. Andes

THE morphology and mechanism of the proeutectoid a and the eutectoid reactions have been recently investigated in some detail in an iodide-base Ti—7.22 pct Cr alloy.' These studies have now been extended to an iodide-base Ti—10.8 pct Cr alloy in order to evaluate the effects of composition on the proeutectoid and eutectoid transformations in titanium-chromium alloys. The alloy used in this investigation had the following composition: 10.8 Cr, 0.0327 0, 0.011 N, 0.0063 H, and 0.011 pct C. Specimens of this alloy were heat treated in evacuated and internally get-tered Vycor capsules. The specimens were solu-

Jan 1, 1959

By Charles White Merrill

Mankind's progress is measured in minerals. Man's emergence from prehistory is marked by passage through a Stone Age and a Bronze Age and into the present era, sometimes called the Iron Age or the Age of Metals. With the evolution of civilization and the development of a modem industrial economy, minerals become more and more important. Structures, roads, and machines are built largely of minerals; the energy to heat the structures and to drive the machines is mostly mineral; agricultural fertility is maintained by mineral fertilizers and water; and military strength is provided by fortresses, armaments, and munitions, largely of mineral origin. Thus in the material world, in the productivity of the economy, access to minerals has paramount importance. Every evidence indicates increasing dependence on minerals in the modem economy, particularly on the mineral fuels as energy sources to provide the power base for advancing industrialization. Both the total and the per capita consumption of almost every mineral is increasing in the industrialized nations. Moreover, nations with predominantly agrarian economies call themselves underdeveloped and universally strive to industrialize. Most mineral consumption trends in the more advanced economies have been greatly exceeding population growth-which itself has been advancing at an accelerating rate-and sometimes have surpassed the growth in real income. Some minerals have only recently been adopted or grown to importance in use. Titanium metal did not appear as a commercial product until 1948, and even coal seriously displaced wood as a source of heat less than two centuries ago. On the other hand, minerals have always played an important role in construction. The prehistoric megaliths that form the dolmens of Salisbury Plain are stone; the pyramids are andesite faced with limestone; and many other ancient structures are built of mineral materials. In modem times the whole course of architecture has been redirected by new building materials, mostly mineral. Most conspicuous is the sky-

Jan 1, 1964

By Donald L. Katz, Leo B. Bicher

A correlation is presented for predicting the viscosities of light paraffin hydrocarbon mixtures such as natural gases for temperatures from o° to 4o0°F. and for pressures fro1 atmospheric to I0,000 lb. per sq. in. The correlation is based on the viscosity data for the methane-propane system and requires only a knowledge of the molecular weight of the naturaI gas. The viscosities of natural gases reported in the literature up to 2500 lb. were reproduced by the correlation with an average deviation of 5.8 per cent. Introduction The viscosity of a natural gas is required whenever calculations are made of the pressure drop that occurs while the gas flows through pipes or porous media. Methods of predicting the viscosities of gases at the present operating pressures are not available. This paper presents a simple method of predicting the viscosity of a natural gas in the single-phase region from its molecular weight, temperature, and pressure. Viscosity oF Methane-propane Mixtures The viscosity of methane, propane, and four of their binary mixtures, 20,40, 60, and 80 mol per cent, have been determined for pressures from 400 to 5000 lb. per sq. in. and temperatures from 77" to 437 F., with an experimental accuracy of 3.2 per cent.2 The apparatus used in the investigation was a modification of that employed in previous studiesaJ4 on the viscosity of normal paraffin hydrocarbons. It consists of a viscosimeter of the rolling-ball, inclined-tube type,5>k7 with auxiliary equipment for making up and charging binary mixtures into the viscosimeter.~ The viscosity data on the methane-propane mixtures have been plotted as a function of molecular weight with lines of constant pressure, charts of constant temperature in Figs. I to 3. These charts are extrapolated at temperatures below 77°F. and at pressures above 5000 lb. per sq. inch. Prediction OF Viscosity from Molecular Weight of a NaturaI. Gas At atmospheric pressure the viscosity of light hydrocarbon gases increased with increased temperature, contrary to the change of viscosity of liquids with temperature. The atmospheric viscosities of the normal paraffin hydrocarbons have been determincd by several investiga-tors 3,4,9,10,12,15,16,17,19 and are plotted in Fig. 4 as a function of molecular weight, with extrapolation to 896'F. and to 220 molecular weight. Data for isopentane and normal pentane show less than 2 per cent difference in viscosity, indicating that Fig. 4 can be used for isomeric parafin hydrocarbons with an accuracy of approximately 2 per cent. Trautz and Sorg'7 determined the atmospheric viscosities 01 methane-propane mixtures and showed that they are proportional to the molecular weight. The viscosities of these mixtures

Jan 1, 1944

By Leo B. Bicher, Donald L. Katz

A correlation is presented for predicting the viscosities of light paraffin hydrocarbon mixtures such as natural gases for temperatures from o° to 4o0°F. and for pressures fro1 atmospheric to I0,000 lb. per sq. in. The correlation is based on the viscosity data for the methane-propane system and requires only a knowledge of the molecular weight of the naturaI gas. The viscosities of natural gases reported in the literature up to 2500 lb. were reproduced by the correlation with an average deviation of 5.8 per cent. Introduction The viscosity of a natural gas is required whenever calculations are made of the pressure drop that occurs while the gas flows through pipes or porous media. Methods of predicting the viscosities of gases at the present operating pressures are not available. This paper presents a simple method of predicting the viscosity of a natural gas in the single-phase region from its molecular weight, temperature, and pressure. Viscosity oF Methane-propane Mixtures The viscosity of methane, propane, and four of their binary mixtures, 20,40, 60, and 80 mol per cent, have been determined for pressures from 400 to 5000 lb. per sq. in. and temperatures from 77" to 437 F., with an experimental accuracy of 3.2 per cent.2 The apparatus used in the investigation was a modification of that employed in previous studiesaJ4 on the viscosity of normal paraffin hydrocarbons. It consists of a viscosimeter of the rolling-ball, inclined-tube type,5>k7 with auxiliary equipment for making up and charging binary mixtures into the viscosimeter.~ The viscosity data on the methane-propane mixtures have been plotted as a function of molecular weight with lines of constant pressure, charts of constant temperature in Figs. I to 3. These charts are extrapolated at temperatures below 77°F. and at pressures above 5000 lb. per sq. inch. Prediction OF Viscosity from Molecular Weight of a NaturaI. Gas At atmospheric pressure the viscosity of light hydrocarbon gases increased with increased temperature, contrary to the change of viscosity of liquids with temperature. The atmospheric viscosities of the normal paraffin hydrocarbons have been determincd by several investiga-tors 3,4,9,10,12,15,16,17,19 and are plotted in Fig. 4 as a function of molecular weight, with extrapolation to 896'F. and to 220 molecular weight. Data for isopentane and normal pentane show less than 2 per cent difference in viscosity, indicating that Fig. 4 can be used for isomeric parafin hydrocarbons with an accuracy of approximately 2 per cent. Trautz and Sorg'7 determined the atmospheric viscosities 01 methane-propane mixtures and showed that they are proportional to the molecular weight. The viscosities of these mixtures

Jan 1, 1944

By Joseph C. Buchen

In principle, productiorl of salt from sea water is a simple operation. The sun and wind cause evaporation of sea water trapped in ponds, and what is left is principally salt. Commercial production, however, requires consideration of many factors. First is a high consistent annual rate of evaporation, as well as large areas of suitable low-lying ground close to economical shipping facilities. The south end of San Francisco Bay has these requisites. Large ponds are built, by using clamshell dredges to build up levees to a height of approximately 3 ft. on ground usually lower than sea level, so that the water may be taken in through tide gates without pumping. Ponds are divided into extremely large concentrating ponds and smeller crystallizing ponds. Approximately ten times more area is required for concentrating than for crystallizing. The concentrating ponds are irregular in shape and size but the crystallizing ponds are rectangular and fairly regular in size, to aid in harvesting. The ocean water is taken into the first of a series of concentrating ponds and gradually moved forward from pond to pond as it increase:: in density, reaehing the crystallizing area as a saturated brine. This brine is pumped into the crystallizer at the beginning of the net evaporating season, usually in May, and further evaporation causes its sodium chloride content to deposit on the bottoms of the ponds. The brine must be drawn off and a fresh supply added from time to time to prevent other undesirable salts from depositing with the sodium chloride. Harvesting usually begins near the end of August and now is accomplished almost entirely by mechanical means. After harvesting, the salt is stored in large sbockpiles until required for shipping or refining. The greatest amount is used for industrial purposes and is shipped without any processing other than screening, but all salt for domestic use produced by the Leslie Salt Co. is refined by the racuum process, giving a produet consistently testing over 09.9 per cent sodium chloride.

Jan 1, 1938

By Joseph C. Buchen

In principle, productiorl of salt from sea water is a simple operation. The sun and wind cause evaporation of sea water trapped in ponds, and what is left is principally salt. Commercial production, however, requires consideration of many factors. First is a high consistent annual rate of evaporation, as well as large areas of suitable low-lying ground close to economical shipping facilities. The south end of San Francisco Bay has these requisites. Large ponds are built, by using clamshell dredges to build up levees to a height of approximately 3 ft. on ground usually lower than sea level, so that the water may be taken in through tide gates without pumping. Ponds are divided into extremely large concentrating ponds and smeller crystallizing ponds. Approximately ten times more area is required for concentrating than for crystallizing. The concentrating ponds are irregular in shape and size but the crystallizing ponds are rectangular and fairly regular in size, to aid in harvesting. The ocean water is taken into the first of a series of concentrating ponds and gradually moved forward from pond to pond as it increase:: in density, reaehing the crystallizing area as a saturated brine. This brine is pumped into the crystallizer at the beginning of the net evaporating season, usually in May, and further evaporation causes its sodium chloride content to deposit on the bottoms of the ponds. The brine must be drawn off and a fresh supply added from time to time to prevent other undesirable salts from depositing with the sodium chloride. Harvesting usually begins near the end of August and now is accomplished almost entirely by mechanical means. After harvesting, the salt is stored in large sbockpiles until required for shipping or refining. The greatest amount is used for industrial purposes and is shipped without any processing other than screening, but all salt for domestic use produced by the Leslie Salt Co. is refined by the racuum process, giving a produet consistently testing over 09.9 per cent sodium chloride.

Jan 1, 1938

By Homer Griffield Turner

The nature and comparative features of anthracite and bituminous coals have been discussed by the writer in two previous papers.' Although this paper is offered as a further contribution to the subject, it seems desirable at the outset to repeat some of the descriptive matter of the early works in order to show the actual connection between various constituents of both coals and the new photomicrographs and other physical and chemical properties. Structure of Anthracite and Bituminous Coals A lump of bituminous coal (Fig. 1) is readily seen to be composed of layers differing from one another in texture, luster and thickness. There are, in general, three kinds of layers, although only two are usually seen. One is deep black, very compact, and has a bright luster; another is grayish black, has a duller luster and is less compact; the third is black, dull and porous in appearance, but because of its thinness is not often seen except on parting surfaces. This last material is charcoal. American students of coal morphology use the names anthraxylon, attritus, and fusain to designate these three constituents of laminated coal. Anthraxylon refers to the brightest bands, attritus to the duller layers, and fusain to the charcoal. Close examination of a lump of bituminous coal shows the brightest deep black layers to be embedded in the duller grayish black laminae. These deep black layers are lens-shaped and vary in thickness from thin sheets to over half an inch. They are often so continuous through the lump that their tapering terminae are not noticeable. On careful examination the duller grayish black laminae (Fig. 7) are seen to contain many very thin sheets of this very bright black material. The charcoal

Jan 1, 1930

By William M. Brewer

Until quite recently, in fact within the past two gears, but little attention has been given to the outcrops on the west coast of Vancouver Island, and their copper-contents. During the past few months the writer has been engaged in examining and developing some of these prospects. In many respects he has found characteristics associated with these prospects which, in his experience, are unique. In the first place, nearly all the outcroppings which overlie chalcopyrite-ore along the west coast of the island are composed of a high-grade magnetite. The magnetic qualities of some of these outcrops arc so pronounced that the magnetite possesses polarity. Although the writer hinlsclf had no analyses of this magnetite made, yet from its appearance he can readily believe that analyses made for other parties, which show a yield' of 62 or 63 per cent. of metallic iron, with only traces of phosphorus and silica, are correct. At a very shallow depth, masses of chalcopyrite, yielding in some instances as high as 32.6 per cent. of copper, occur associated with the magnetite; and in one instance, which recently came under the writer's observation, a solid body of high-grade chalcopyrite, fully 4 feet in thickness, occurs Within 6 feet of ; the surface. Usually this solid sulphide-ore carries low values in gold. Probably ail average of' $2 per toil would be fairly representative. But in some instances development has determined the occurrence of narrow stringers of pyritous quartz, associated with the sulphide-ores, which yield by assay more than $20 per ton in gold. In the districts examined by the writer, the country-rock is usually crystalline limestone, with dikes of igneous rock as intrusions. Sometimes the outcrops of magnetic iron-ore are

Jan 1, 1900

A. W. TRACY' AND D. H. THOMPSON (presented in written form).-Messrs. Ed¬munds, Anderson and Waring are to be commended for their excellent work in so painstakingly reducing to constants, the variables believed to be associated with these types of stress corrosion. An ammonia stress-cracking apparatus similar in many respects to the one described has been assembled. Certain aspects of its construction may be of interest. Tensile loading of the specimens, which are usually Y8-in. diameter wires, is accomplished by springs acting in compression in compact, portable, tubular assemblies weighing less than 10 lb. The lower end of each assembly contains the test specimen and is passed into the test chamber for exposure to the moist ammoniacal atmosphere. There is considerable convenience in being able to load the specimens in a portable unit, which may be warmed to prevent condensation, and then thrust instantaneously into the test chamber. Spring loading obviates the use of weights, but it has the disadvantage of allowing some relaxation of the load if the specimen elongates during corrosion. The maximum loss in load found so far was 20 per cent. The air supplied to the test chamber is humidified by passing it through thermo¬statically controlled water. The air is dispersed into fine bubbles by being forced through a porous ceramic filter at the bottom of a tank containing about 10 liters of water. The temperature of the water is controlled independently of the tempera¬ture of the test chamber. Thus, with the

Jan 1, 1945

By Francis R. Conley, John A. Sievert, John N. Dew

A brief review is presented of the past performance of a number of large, thin, highly permeable reservoirs with low dips in the Bolivar Coastal fields of Venezuela. The performance of these reservoirs indicates that the fluids are segregated vertically within the sand section by gravity. With this assumption, equations are developed which describe the performance under pressure maintenance operations. Methods of solving these equations and results of simple example calculations are presented. Example calculations indicate that under pressure maintenance conditions injected gas tends to {tow preferentially along the top of the sands and that encroaching water has a tendency to flow preferentially along the bottom. The expected performance of segregated fluids is discussed and compared with that of fluids which are uniformly distributed in any sand section. INTRODUCTION The field performance of a number of reservoirs described herein indicates that the fluids are segregated vertically within the sand section by the force of gravity. Thus, it was felt that any method used to predict the future performance of these reservoirs should consider the effects of segregation in the sand sections. A study of the available information on some of the reservoirs suggests that increased recoveries may be expected if the reservoir pressure is maintained by either crestal gas injection or flank water injection. To predict future performance of reservoirs under pressure maintenance operations, a method of analysis was needed which would account for segregation of fluids in the sand sections. Several methods of analysis have been developed to take into account the segregation of fluids in the reservoir as a whole1,3 To our knowledge no method considers segregation of the fluids within sand sections in the manner indicated by the past performance of several reservoirs in the Mara-caibo Basin. This paper outlines part of the work done in studying some of these reservoirs and contains a description of their performance characteristics. The analysis presented is restricted to pressure maintenance conditions, since space limitations prevent a full discus- sion of the development of the mathematical relations and the various methods of solving them. Only a sketch of the development of the mathematical relations is given. The various methods of solving these relations are pointed out, but the actual determination of solutions to various problems are omitted except for one example. It is felt that these results may aid in the study of reservoirs outside the Maracaibo Basin. Some concepts on which the present analysis is based are outlined by D. N. Dietz. However, the analysis presented herein includes several factors not considered by Dietz: (1) variations in permeability and in the cross section, (2) various shapes of the cross section, and (3) the production of fluids. Also, the mathematical development presented by Dietz differs considerably from our corresponding analysis. RESERVOIR CHARACTERISTICS The reservoirs under consideration, large and thin, with low dip and high permeability, are large to the extent that they contain from 0.5 to over four billion bbl of oil initially in place. The section thicknesses vary from 100 to 400 ft and the lengths from 10,000 to 40,000 ft. Thus, a length-wise cross section of the producing formation appears to be long and thin. The dip angles vary from 0 to 6 degrees and the average permeabilities vary from 0.5 to over three darcies. The reservoirs contain from 20 to 50 per cent shale inter-laminated with the productive sands. Most shale breaks within the major sands do not correlate from one well to the next, and correlation is often difficult, even between wells drilled from the same location. However, it is often possible to correlate the shale breaks between major sands for some distance. Herein we are concerned with the performance of reservoirs containing oil of gravities over 20" API. Past reservoir performance indicates good pressure communication and, in cases where pressure sinks have developed, large amounts of fluid migration have occurred. Few of the reservoirs have had initial gas caps, but also, few have been found to be highly under-saturated. Due to gravity segregation, secondary gas caps usually form before the pressure has been reduced more than 25 per cent of its initial value. The effect of gravity has not only been apparent on a reservoir-wide basis, but has also caused segregation of the reservoir fluids in productive sections. Proof of this is found from the results of selective well tests, workovers, and electric and various other types of logs. Evidence that

By H. D. Dahl, Roger C. Parsons

In order to improve roof stability, Continental Oil Co.'s research program, initiated in 1969, was directed toward defining the geological parameters that affect the severity of roof conditions in any particular area of the mine. In addition, the program was seeking to define why roof falls in the Humphrey No. 7 mine (and in northern West Virginia-southwestern Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. Conclusions and recommendations from this study of roof fall orientation are given.

Jan 1, 1973

By D. W. Rudd, D. W. Vose, S. Johnson

The permeability of Mo-0.5 pel Ti to hydrogen was investigated over a limited range of temperature and pressuire (709° to 1100°C, 1.i and 2.0 atm). The resulting permeability, p, is found to obey the The experimental data justifies the permeation mechanism as a diffusion contl-olled pnssage of Ilvdrogen atoms through the metal barrier. 1 HE permeability of metals to hydrogen has been investigated by a number of workers and their published results have been tabulated by Barrer' up to 1951. Since most of the work on the permeability has been accomplished prior to this date, the compilation is fairly complete. Mathematical discussion of the permeability process has been reported by Barrer, smithells, and more recently by zener. From these efforts several facts are observed. First, the permeability of metals to diatomic gases involves the passage through the metal of individual atoms of the permeating gas. This is evidenced by the fact that the rate of permeation is directly proportional to the square root of the gas pressure. Second, the gas permeates the lattice of the metal and not along grain boundaries. It was shown by Smithells and Ransley that the rate of permeation through single-crystal iron was the same after the iron had been recrystallized into several smaller crystals. Third, it has been observed that the rate of permeation is inversely proportional to the thickness of the metal membrane. Johnson and Larose5 verified these phenomena by measurirlg the permeation of oxygen through silver foils of various thicknesses. Similar findings were noted by Lombard6 for the system H-Ni and by Lewkonja and Baukloh7 for H-Fe. Finally, it has been determined that for a gas to permeate a metal, activated adsorption of the gas on the metal must take place. Rare gases are not adsorbed by metals, and attempts to measure permeabilities of these gases have proved futile. ~~der' found negative results on the permeability of iron to argon. Also, Baukloh and Kayser found nickel impervious to helium, neon, argon, and krypton. From what was stated above concerning the dependence of the rate on the reciprocal thickness of the metal barrier, it is seen that although adsorption is a very important process, at least in determining whether permeation will or will not ensue, it is not the rate determining process for the common metals. A case in which adsorption is of sufficient inlportance to cause abnormal behavior has been noted in the case of Inconel-hydrogen and various stainless steels.'' APPARATUS The apparatus used in this study is shown in Fig. 1. The membrane is a thin disc (A), but is an integral part of an entire membrane assembly. The entire unit is one piece, being machined from a solid ingot of metal stock. When finished, the membrane assembly is about 5 in. long. Two membrane assemblies were made; the dimensions of the membranes are given in Table I. The wall thickness is large compared to the thickness of the membrane, being on the average in the ratio of 13 to 1. There exists in this design the possibility that some gas may diffuse around the corner section of the membrane where it joins the walls of the membrane assembly, If such an effect is present, it is of a small order of magnitude, as evidenced by the agreement of the values of permeability between the two membranes under the same temperature and pressure. A thermocouple well (B) is drilled to the vicinity of the membrane. The entire membrane assembly is then encased in an Inconel jacket and mounted in a resistance furnace. The interior of the jacket is connected to an auxiliary vacuum pump and is always kept evacuated so that the membrane assembly will suffer no oxidation at the temperatures at which measurements are taken. The advantages of this configuration are: 1) there are no welds about the membrane itself, so that the chance of welding material diffusing into the membrane at elevated temperatures is remote. 2) It is possible to maintain the membrane at a constant temperature. Since the resulting permeation rate is very dependent upon temperature, it is advisable to be as free as possible from all temperature gradients. 3) It is possible to obtain reproducible results using different specimens. The only disadvantage to this configuration is the welds (at C) in the hot zone. The welding of molybdenum to the degree of per-

Jan 1, 1962

By Jerome J. English, Gordon W. Powell

An experimental investigation and mathematical analysis of the thermal-dilation behavior of the titanium alloy Ti-7Al-3Cb have shown that the linear dimensional changes associated with the polymorphic transformation need not be isotropic. The absolute magnitude of the linear dimensional change, which may be either positiue or negative, associated with the cr-p transformation is dependent upon the relutzve volumes of different orientations of the transformation product. It is hypothesized that the dilation irregulati-ties that have been observed during the polymorphic transformation of pure, coarse-grained titanium and other titanium-base alloys can be explained in the same manner. When titanium is heated above about 165O°F, the hcp a structure transforms to bcc 0. Thermal-dilatioh measurements have shown that the transformation is accompanied by a decrease in length of 0.16 pct.' Such dilation behavior would be expected because the volume of the hcp unit cell is about 0.3 to 0.4 pct greater than that of the bcc unit cell. A recent investigation2 of the thermal-dilation behavior of an experimental a-p* titanium alloy, Ti- 7A1-3Cb, containing 0.06 wt pct 0 showed that its dilation behavior during the polymorphic transformation differed substantially from that reported for unalloyed titanium. The first time the alloy was cycled through the transformation, the dilation curve closely duplicated that of unalloyed titanium. However, upon repeated cycling through the transformation temperature range, both the magnitude and the sign of the dimensional change associated with the transformation were observed to vary with each cycle. This investigation was undertaken to obtain additional data on the dimensional changes associated with the polymorphic transformation in the Ti-7A1-3Cb alloy and to determine the cause of the dimensional irregularities. After testing, the specimens were examined metallo-graphically. In addition, Laue back-reflection patterns were obtained from selected sections taken perpendicular to the specimen axes to determine the a orientations present in these sections. White radiation from a tungsten target and a 0.1-mm-diam collimator were used to produce the diffraction patterns. RESULTS Dilation Curves. Three types of thermal-dilation curves were obtained when the a-8 titanium alloy was heated and cooled through the transformation temperature range. These three types of curves are illustrated in Fig. 1. The type I curve represents what is considered normal behavior, because the dilation change is what would be expected on the basis of the volumes of the unit cells of a and p. The Type I1 curve is the inverse of Type I. Normal behavior is characterized by an expansion on cooling through the transformation, whereas a contraction takes place in the Type 11 curve. With Type ni behavior, no clearly distinguishable length change occurs during the transformation. No other anomalies that might be indicative of other phase transformations were observed in the dilation curves at lower temperatures. Apparently, the cooling rate was low enough for equilibrium to be reached during the 0 to a transformation. Table I lists the types of dilation curves observed during the polymorphic transformation as a function of the direction of measurement and cycle number. The A1 value was determined by extrapolating the low-temperature (a + 5 pct p) and high-temperature (100 pct p) segments of the dilation curves to a common temperature and measuring the difference in the or-dinates at that temperature, see Fig. 1. The transformation occurs over a temperature range in this alloy, so the magnitude of A1 is not an absolute value but depends on the choice of temperature. A mean temperature, T,, within the transformation temperature range was selected for the measurement. T, on cooling occurred about 100°C lower than T, on heating. The first time each of the three dilation specimens was heated to above the temperature, that is, Cycle 2, normal Type I behavior was observed. In Cycle 3, two deviations from normal behavior occurred. First, during cooling of the longitudinal specimen, a substantially larger expansion, +0.21 pct, was measured as 0 transformed to a compared with +0.03 pct in Cycle 2. Second, the thickness specimen was observed to undergo a contraction instead of the anticipated expansion on cooling. Continued cycling of the three specimens from room temperature to 2500°F produced additional changes in the dilation behavior. These changes did not seem to be related to the fabrication direction of the alloy because the values of a1 for the longitudinal, transverse, and thickness specimens varied unpredictably in magnitude and sign. Furthermore, both the longitudinal and transverse specimens showed all three types of dilation curves at least once during the six cycles that they received. Fig. 2 is a sketch of the transverse specimen after

Jan 1, 1967

By W. R. Ingalls

ThE following chronology presents the history of lead-mining in the United States in a brief form and is a useful reference in connection with the statistics of production: 1621.. Lead was mined and smelted near Falling Creek, Va., to supply the local demand for bullets and shot. This was the first mining and .smelting of lead in what is now the United States. 1632. In a report made on the minerals of New England, lead-ore is mentioned. (Bishop, I., 470.) 1650. Supposed beginning of mining by Jesuits in Pima county, Ariz. 1651. Grant of lead-mine at Middletown, Conn., to Gov. John Winthrop. 1682. Lead-ore supposed to have been discovered in Wisconsin by Nicholas Perrot. (K. D. Irving, Mineral Resources of Wisconsin, Trans., viii., 498.) 1700 Discovery of lead in Missouri by Penicaut, one of Le Sueur's party. Tile same expedition discovered lead near the southern boundary of Wisconsin in August of the same year. 1712. Grant by Louis XIV. of the Crozat patents, with special privileges respecting the discovery and operation of mines in the then territory of Louisiana. Little or no mining was done under this patent until about 1720. 1717. Transfer of Crozat patents to the Mississippi Co., promoted by John Law, which prepared for active mining. 1719. First attempt to mine and smelt lead in Missouri, made by Sieur de Lochon, in behalf of the Mississippi Co., near Meramec river. Results unsuccessful.

Jan 1, 1908

By Walter Weeks

THE process of cooling air by allowing it to expand and do work in an engine is well known, but the theory of obtaining cold air by free expansion without the aid of an engine operating with cutoff has been little discussed. CASE I If compressed air is allowed to expand to the atmospheric pressure through an orifice in an air line that is supplied by a running compressor, no cooling results except the negligible one due to the Joule-Thompson effect, which will not be considered in this discussion. The effect of moisture will also be neglected.

Jan 1, 1937

By C. W. Volek, J. E. Chappelear

The injection of a hot liquid into initially cool porous media, saturated with the same liquid and surrounded by two impermeable but heat conducting media (cap and base rock), has been studied both experimentally and theoretically. The temperature dependence of the viscosity was included in the theoretical model, but it was assumed that the specilic heats and densities of the various materials were independent of the temperature. Solutions to the theoretical model were approximated by numerical methods. Both theoretical and experimental results indicate that center-line temperatures are significantly higher than boundary temperatures. Comparison of experimental and theoretical results with a cold/hot viscosity ratio 01 19:1 were in reasonable agreement. Theoretical calculations show that the effect of the temperature dependence of viscosity was very significant at ratios of 100:l to 1000:1, which are typical of those that occur when injecting hot water to flood heavy oil reservoirs. INTRODUCTION We consider the problem of prediction of fluid flow and temperature distribution in an initially cold-fluid-filled reservoir on the injection of the same hot liquid by the use of mathematical and physical models. The results reported are for a two-dimensional rectangular section of the reservoir, as shown in Fig. 1. The injection and withdrawal faces are assumed to be equipotentials for fluid flow. The ultimate purpose of such models would be to predict hot-water injection performance. However, we note that in the work presented here, one of the most significant aspects of the problem — the instabilities resulting from two-phase, water and oil flow — is not included. We will not give a historical review, but refer instead to the paper of Spillette and Nielsen,1 which contains a rather complete bibliography and critical discussion. The physical problem is exactly the same as Spillette and Nielsen, except for certain simplifications in our assumptions. The mathematical details are somewhat different, and we will present the details of our method here. The mass flow equation, which is elliptic in character, is handled by successive overrelaxation. The heat flow equation, which is parabolic in character, is handled by a straightforward explicit approximation. Some difficulty arose in the over-all heat balance due to small errors in the solution of the mass flow equation, and we feel that a different formulation of the heat flow equation would be desirable for future work. In addition to the mathematical solutions for the temperature distributions in a porous medium due to the injection of hot liquids, experimental data are presented to check the validity of these solutions. A schematic diagram of the model is shown in Fig. 2. Certain qualitative physical conclusions were obtained from our numerical and experimental results. These are: 1. Assuming high (infinite) conductivity normal to the bedding plane in the reservoir is a poor approximation, and may lead to overestimates of the total heat losses (to cap and base rock) of as much as 50 percent. 2. More heat is retained in the reservoir (per unit of heat injected) for higher viscosity changes. 3. Any particular temperature isotherm moves more rapidly along the center line for higher viscosity changes. Consequently, the approximation of temperature independent viscosity is not suitable for obtaining quantitatively correct results. MATHEMATICAL MODEL Our mathematical model is that of a reservoir of thickness 2h. The problem is idealized from that of a linear hot-water drive, and we imagine that the input face is sufficiently far away from the injection wells that the stream lines enter it normally. Similarly the production wells are far enough from the outflow face that the flow lines leave it normally. The reservoir and surrounding cap and base rock

Jan 1, 1970

Do not write until you have something to say. Think first; then write. In order to be understood, you must know what you wish to say. Clear writing is the consequence of clear thinking. Therefore consider your subject well before you begin to write; ruminate on it; marshal the salient facts in your mind; saturate yourself with the ideas you wish to express and with cognate ideas; then express yourself deliberately. If you are bubbling over with your subject the words will come, but you might as well expect to sail without a breeze as hope to give life to words without the living thought. Here I may advert to the fact that among the uneducated it is a common expectation to acquire the knack of writing without taking the trouble to study the art of literature. I overheard a woman in a suburban train remark to her neighbor: "I'd like to be able to write well without stopping to think about it". She was one of many that would like to do a thing well without the trouble of thinking; but it cannot be done in respect of anything to which thought is essential. The possession of a good voice does not justify a person in expecting to sing successfully to a large audience; before singing in public one has to master the technique of singing; one has to learn first how to breathe properly, how to enunciate, and many other things. The successful singer is an artist, not a megaphone. Most of us would regard a man or a woman without any training in the art of singing as a fool or an impostor if he or she were to give a public concert, yet we do not recognize the equal foolishness and imposture of persons that write books before they have studied the technique of writing. That is why so many books are unreadable, and why many books by clever men are difficult to read. They start to write books before

Jan 1, 1931

By W. L. Phillips

The plastic properties of lithium fluoride and magnesium oxide under compression were investigated in the temperature range 25° to 1000°C. At the higher test temperatures, the critical resolved shear stress and the rate of work-hardening of both materials decreased. At the same time, the number of stress lines decreased and the individual stress lines became wider. The density of dislocations decreased for a given strain the higher the test temperature for lithium fluoride. The decrease in the critical resolved shear stress as a function of temperature could be fitted by the equation 7 = Toe-KT. THE influence of temperature on the stress-strain curves of a variety of metal single crystals has been studied for a wide range of temperature.1"5 In general, it has been found that both the critical resolved shear stress and the rate of work-hardening decrease rapidly with increasing temperature and fall to a value of essentially zero well before the melting point is reached. AS the test temperature is increased, the density of slip lines has been found to decrease, while the width of the individual lines increases. Recently, Gallagher,' Graf et al.,7 and Pate1 and Alexander8 have found that single crystals of germanium and silicon, which have a covalent bond, can be plastically deformed at elevated temperatures. In compressing germanium it has been found that the strain-hardening coefficient decreased very rapidly as the temperature was increased. The coefficient did not tend to zero, however, as the melting point was approached. The plastic properties of ionic crystals at elevated temperatures have not been extensively investigated. In the only work previously reported Tamman and salge9 and Theile10 have shown that the yield point of sodium chloride single crystals tested in tension and compression decreased slowly with increasing temperature, falling to zero at the melting point. As the temperature was increased, they found a substantial increase in the amount of plastic deformation that could be sustained before fracture; and at temperatures above 400°C in tension tests there was an obvious necking which produced local extensions of up to 3000 pct. The purpose of the present work is to extend the knowledge of high-temperature deformation to the ionic crystals, lithium fluoride and magnesium oxide. The following were investigated: 1) The gross shape of the stress-strain curve at several temperatures. 2) The change in the critical resolved shear stress as a function of temperature. 3) The appearance of slip bands and the density of dislocations as a function of strain and temperature. EXPERIMENTAL TECHNIQUES The lithium fluoride and magnesium oxide used in this investigation were purchased from the Harshaw

Jan 1, 1961