Search Documents

By J. E. Burke, Y. G. Shiau

Several attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealmg. Two fundamentally different hypotheses have been advanced, with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary. The theory of Jeffriesl that grain size and grain size contrast control growth is an example. The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary. The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely. The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration. A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel.³ Although it is generally stated that grain growth does not precede recrystallization, several workers4-5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some grain boundary migration. The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that can be introduced by mechanical deformation. An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used. It was also planned to determine the effect of such deformation on the rate of growth in a specimen which would show growth in the unstrained condition. Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures. French7 has reported that at deformations less than 17 pet it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under condition~ of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a Small extent. Experimental Procedure The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1949

By J. P. Hirth, A. H. Clauer

A simple graphical method is presented for the determination of climb forces on dislocations exerted by uniaxial stresses. In conjunction with standard stereographic projections, the technique is applicable for any crystal system. Climb forces on glide dislocations in bcc crystals are determined as an application. In connection with a study1 of elevated temperature creep of molybdenum single crystals, a detailed analysis of the climb force on a dislocation was necessary. In general, such forces can be calculated for an arbitrary dislocation segment from the Peach-Koehler equation2 (or one of its variants3"6) where Fk are the components of the force per unit length of dislocation line, ?i of the unit sense vector tangent to the line, ojl of the stress tensor, bl of the dislocation Burgers vector, and is the Einstein permutation operator with components ?123 = ?231 = ?321 = —?132 = — ?321 = —?—213 = unity, and all other components zero. It is understood in the suffix notation of Eq. [I.] that repeated indices are to be summed over 1, 2, and 3. For the most general coordinate system, the matrix manipulations required to solve Eq. [I] are fairly complex. However, a simplification can be achieved by specifying a coordinate system based on the dislocation in question. The pertinent system involves cartesian coordinates xi, x;, xi, with attendant unit vectors e'i; ei being parallel to the Burgers vector b, and e'3; being parallel to the climb directions (b x ?), i.e., normal to the slip plane. In this coordnate system b = (bi, 0, 0) and ? = (?'1,?'2, 0). Hence, Eq. [I] yields for the climb force per unit length F3 = ?'2s'11b'1—?'1s'12b'1 [2] The first term on the right side of Eq. [2] is the climb force on the edge component of the dislocation, while the second is the (cross-slip) force normal to the glide plane acting on the screw component. Thus, the problem of determining the climb force reduces to that of resolving the stress components —il and s'12 in the xi coordinate system. Several authors7- l0 have shown, for the glide case, that such stress resolution can be performed most readily by graphical methods. Therefore, we present a similar method for the climb case. Of the suggested methods, we follow that of Hartley and Hirth,9 which can be performed directly with a standard stereographic projection for the crystal system in question. We treat the case of simple tension, or compression, this being the most common creep test in which climb is important. A set of cartesian coordinates (x1, x2, x3) is fixed with x3 parallel to the specimen axis. This set is connected to the x'i set by the factors defined in Table I. A perspective view of the coordinate systems relating them to the glide ellipse, is given in Fig. 1, while a stereographic projection of the coordinate systems is presented in Fig. 2. The transformation matrix connecting the xi and xi coordinates is x'i =aijXj [3] where an a11 a13 aij = a21 a22 a23 a31 a23 [4] s The corresponding transformation for the stresses is i [5] The only nonzero component of okl for the simple tension case is s33,. Hence, using Eqs. [4] and 151, we find that Eq. [2] becomes F3 = b'1s33 sin2 cos ?[cos ? sin a - sin ? cos a] [6] = m1b'1s033 sin a- rn2b's33 cos a where sin a = 5: and cos a = ?i, with a the angle measured from b to ?, i.e., a polar angle in the x1, x2 plane. The same equation with a sign change applies for compression. A graphical plot of the "Schmid" factor m1, relating to the climb force on the edge component, is presented in the stereographic projection of Fig. 3. In this projection the glide plane normal points toward the top of the page and the glide direction points normal to the plane of the page. To use the graph, one

Jan 1, 1970

[ ] TUNNELS TO BINS. Originally designed for tunnel work, the strong lightweight liner plates used to construct this 30-ft diameter, 31-ft high, aggregate storage bin have several advantages. Bins and conveyor to tunnels can be quickly erected in any season, for permanent service, or to be salvaged and reused. Armco Steel Corp. (16) ROLLER CHAIN: Engineering Data Book No. 2457 published by Link-Belt Co. is a comprehensive 148-page volume on roller chain and its application. Detailed engineering information covers installation, maintenance and lubrication of chains for drives, conveyors, and sprocket wheels. The book covers selection of drives to meet both standard and special installations. (17) LABORATORIES: The Fisher Scientific Co's. line of 21 basic units of standardized steel laboratory furniture is described in catalog no. 25. The Unitized line was designed to combine the advantages of custom installation with the convenience of selection, delivery and continued flexibility that goes with ready-made units. (18) PUMPS: Two similar, but functionally different types of vertical centrifugal wet-pit pumps; a heavy duty bilge pump for handling solids-free liquids and drainage; and a screenless sewage ejector, constructed to handle sewage and solids carrying liquid; are illustrated in a bulletin from Yeomans Bros. Co.

Jan 1, 1952

NEW MEMBERS The following list comprises the names of those persons Who became members during the period July 10, 1918, to Aug. 10, 1918. ARCHER, EUGENE G., assayer and Chem., Granby Cons. Min. Smelt. & Power Co.,Anyox, B. C., Canada. BAKER, ROBERT C Mech. Engr. and Draftsman, Moctezuma Copper Co., Nacozari, Son., Mexico. BARNES, EDWARD A Supt., Fort Wayne Works, General Electric Co., Fort Wayne, Ind. BARNHART, EDWIN Engr. of Tests, Bethlehem Steel Co., Sparrow's Point, Md. BENSLEY, MAURICE D Pres. and Mgr., Frontier Brass Foundry, Inc., Niagara Falls, N. Y. BRADLEY, JOHN C Met., The American Brass Co., Waterbury, Conn. BRAGG, C. T Works Mgr., Michigan Smelt. & Refin. Co., Detroit, Mich. BRYMER, GEORGE W Min. Engr., 922 Union National Bank Bldg., Scranton, Pa. CHIVVIS, NORMAN Met. Engr., More-Jones Brass & Metal Co., 3144 North Broadway, St. Louis, Mo. CRAWFORD, R. D Prof. of Mineralogy & Petrology, Univ. of Colorado, Boulder, Colo.

Jan 9, 1918

By Robert Glass Cleland

WALTER DOUGLAS succeeded his father, Dr. James Douglas, as president of Phelps Dodge in 1916. Before assuming office, the new president had been assayer at Bisbee, superintendent of the Copper Queen, general manager of all the Phelps Dodge mining interests, and altogether had spent a full quarter of a century in various phases of the company's business. Energetic and imaginative, experienced and courageous, he had need of all these qualities before he surrendered the direction of affairs into younger hands, fourteen years later. For the period of his administration was one of sudden ebb apd flow, flush production, drastic curtailment, quick recovery, and near-disaster. In 1917, soon after Walter Douglas became president, Phelps, Dodge & Co., Inc., which had been formed in 1908 as a holding company, went through an internal reorganization for the purpose of simplifying the structure and changing it from a holding company to an operating company. The Copper Queen Consolidated Mining Company, which had the necessary charter power and authority to carry on the business of any and all the subsidiary com-

Jan 1, 1952

By R. S. Shoemaker, F. W. McQuiston

CAMPBELL RED LAKE MINES Balmertown, Ontario 1974 Operating Data MINE LOCATION: Balmertown, in Red Lake mining area of Ontario TYPE OF MINE: Underground mine developed by vertical shaft to 4300 feet. Mining active above 3000 ft depth. ORE DESCRIPTION: Gold and minor silver.. Sulfur content about 1.3%. Ar senopyrite , pyrite, pyrrhotite, and stibnite. CAPACITY IN TONS124 HRS: 825 ASSAY: 0.66 oz Au per ton heads MILL PROCESS: Amalgamation, flotation, roasting of concentrate and separate treatment of calcines and flotation tails by cyanide. PLANT BUILDING: Mine mill and service facilities all housed in insulated and heated buildings POWER: Total consumption, mine and mill - 100 Kwh/T WASTE DISPOSAL: Impoundment of tailings. Arsenic to sealed underground storage EMPLOYEES: Total of 300 men on payroll. Housing in Balmertown and nearby communities.

Jan 1, 1975

By A. Mitchell, M. Etienne

VARIOUS'-3 reports on the electroslag remelting process refer to the "thin skin of slag" existing around the slag pool and the solidifying ingot, but none considers the various mechanisms by which this layer forms and thus influences the surface quality of the ingot. A vertical section4,5 of the Cao-CaF2-Al2O3 diagram is shown in Fig. 1 between CaF2 and 6Al2.CaO3 From this, it is seen that a typical "70:30" CaF2:A1a3 slag will solidify to produce 6Al2O3.CaO primary phase in a eutectic matrix. The commercial slags contain sufficient CaO to produce* this composition by both the

Jan 1, 1969

By George S. Rice

The extremely valuable papers and discussions on coal-cluat explosions by Bache,' Eavenson, Shurick, Mannakee,* and Raymond are of unusual interest to me, since it has been my duty to carry on investigations on this and allied subjects for the Technologic Branch of the United States Geological Survey during the past year, and to make a series of coal-dust tests in the explosion-gallery at Pittsburg during a short periocl when its use could be diverted from the pressing work of testing explosives. In several of the discussions mentioned, it has been assumecl that the Technologic Branch of the Survey mas not paying attention to certain phases of the general problem, or to the specific question of temperature and humidity of mine-air in its effect upon the explosibility of coal-dust. This assumption is not correct, since from the time of the establishment of the " Mine-Accident Division," with its subdivisions of explosives, rescue-work, and mine-investigation, the mining engineer.; of the last-named section have made the subject one of chief consideration. Their general duties, including mine-sampling for governmeilt purposes, emergency-calls for rescue-work, and esplosion investigations, have prevented undivided attention, but all of them have been supplied with instruments for such determinations, and special report-forms have been in use and a great many observations made in mining-districts to which the mining engineers have gone. With the idea of obtaining a uniform system of reporting these data, and in the hope that the work may be of service to mining engineers in the field, the collecting blanks in use are shown in Forrns 1 and 2.

Jan 1, 1911

By C. J. Delisio

The basic concept of tunnel boring has not changed since the late 1800's. R. Stanley of Great Britain obtained a Canadian patent as early as December 1891. Mr. Stanley's machine was a device that consisted of a rotating wheel equipped with drag-type teeth; it had a means of thrusting the cutterhead against the face or heading; it had a means of clamping or gripping the machine in its bore; it had a means of collecting and depositing the cuttings into a screw-type conveyor located near the invert of the tunnel. It even had a means of varying the speed of the forward motion of the machine to suit different hardnesses of rock encountered. This description essentially fits the latest tunnel-boring machines being built today. In short, there has been no significant advance in the basic concept in 70 to 80 years. It may well be that no significant change can be expected for some time into the future. Today's machines, while still basic in concept, offer many advances aimed at faster tunneling. Among these are 1 ) improved cutters, 2) guidance and steering devices, 3) dust-control devices, and 4) mechanisms to aid in installing tunnel supports. CUTTERS The most important part of a hard-rock tunnel borer is the cutter. If the cutter can cut the rock, it is a boring machine. If the cutter cannot cut the rock, no other part of the machine can. When Jarva, Inc. decided to build a machine, the first problem was to find a good cutter. In our search, we looked at most of the cutters on the market. We selected Reed Drilling Tools' cutter because the design of their cutter was aimed at hard-rock tunneling. We feel that they build the best cutter available and provide the best possible service to their customers. As tunnel-boring machine design advanced, the transition from drag bits to roller bits was natural because harder formations required a roller bit, and it is the goal of all mole users to bore harder formations. Roller bits

Jan 1, 1970

By W. B. Morrison

Anderson, King, and Spreadborough present detailed evidence to show what ~aldwin~' has already pointed out, that, over a relatively small grain-size range (Ad"1/2 ^ 10 mm-'I2, d is average grain diameter), yield point data can fit a number of relationships. Part of the difficulty in obtaining data which reflect only the effect of change in grain size on yielding arises from the fact that in varying the grain size, even though great care is taken, other structural changes are almost certain to occur. In iron alloys, these changes may consist of variations in subgrain size, grain boundary ledge density, and degree of carbon and nitrogen segregation at grain boundaries, all of which are difficult to detect and which may affect yielding, primarily through their effect on dislocation generation. Because of the inherent inaccuracy associated with yield point measurements there is little point in using relatively complex equations to fit data, as was done by Anderson et mnl., rather than the simpler, widely used Hall-Petch equation. In compiling their table of data, it is surprising that they did not include results from certain low-carbon steels,31 in which, as illustrated in Fig. 2, the grain-size range is very much larger than in their Armco Iron. The very fine grains in these steels were obtained by a thermomechanical process. Examination by electron microscopy showed that the grains were separated by high-angle boundarie and contained only an occasional subboundary. The data from these steels obeyed the Hall-Petch equation, and it was shown quite conclusively that they did not fit a d-l or (1-lJ3 relationship. Obviously, a much wider range in grain size than used by Anderson et al. is desirable if we are to determine the true relation between lower yield stress and grain size.

Jan 1, 1969

By AIME AIME

COAL preparation will be the main topic discussed at the first fall meeting of the Coal Division at Pittsburgh, Sept. 11, 12 and 13, though valuation, mergers, safety, stream pollution and other topics will not' be neglected. It is particularly appropriate that the great changes taking place in preparing coal for the market should be discussed at length where in the plants of the Pittsburgh Coal Co. and others the opportunity is afforded to see on a large scale just what is being accomplished. In wartime, the United States broke all records in coal production, but, as the late Franklin K. Lane pointed out, every fifth car shipped consisted of dirt. Obviously that constituted a big bur- den on industry and, in the remaking of the business which is now taking place both in the anthracite and bituminous fields, clean coal has properly enough be- come a watchward. Central coal-cleaning plants are being erected as a part answer to the puzzled inquiry of those familiar with metal mining as to why miners of coal have so long been content with what are relatively small units of production. Gradually big collieries comparable in tonnage output to the biggest copper mines are being built, and excellent examples are to be seen near Pittsburgh. Even the age-long tradition of the coal operator in favor of the single shift is

Jan 1, 1930

By R. H. Richman, F. Borik

A 0.3 pct C-12 pct Cr-6 pct Ni steel was rolled to 93 pct reduclion in area as austenite at 510°C, and then partially transformed as desired to ~rlartensite by qnenching to - 196°C. Pole figures for the austenitic matrix and for the martensitic product were separately determined by an X-ray transmission method. The deforitration texture of' the warm-worked austenite is characlerized by (110)(225) components, and is thus closely similar to those produced in a brasses. The pole jigure of the martensite in partially transformed material agrees well with that which can be constructed by transfortnation of the {110)(225) orientations according to either the Kuvdjuniov- Sacks or the Nishi-yatuu relatiotship. Howeuer, an important result of this construction is that me-third of the predicted orientations are missing. A graphical analysis can then be used to show that in deformed austenite certain crystallographic variants of martensite (related to the most probable austenite slip systems) are suppressed, resulting in this preferred transformation. The evidence for preferred transformation is corroborated by the measured elastic anisotropy of warm-rolled and fully transformed H-11 steel. EXTENSIVE plastic deformation of a polycrystal-line aggregate in a manner that causes flow predominantly in one direction results in a preferred orientation of the constituent crystallites. The particular orientations that are produced depend upon the crystal structure and composition of the material, as well as upon the temperature, mode, and degree of deformation; in any case, the preferred crystallo-graphic orientations, or textures, are reflected in directionality of mechanical properties. Although such anisotropy may be exploited in certain specialized applications, it is more commonly diminished or eliminated by heat treatment lest it interfere undesirably in subsequent forming operations or in structural design. In the recently developed thermomechanical treatments that significantly enhance the strength of some steels,1,2 considerable deformation of the metastable austenite prior to the martensite transformation is essential to the strengthening process. If the austenite is textured by the deformation, and if the transformation to martensite proceeds according to one of the relationships established for transformation in annealed austenite, then it must be expected that the martensite will also possess a preferred orientation even though the multiplicity of martensite orientations possible in a given austen- ite crystal will tend to restore some degree of randomness. The existence of a residual anisotropy, both mechanical 3-6 and crystallographic,' has been substantiated. In the latter crystallographic investigation, preferred orientations were determined for the martensitic structure of an SAE 4340 steel rolled 72 pct as austenite at 833°C and then quenched. However, the choice of a composition that transformed almost completely to martensite during the quench to room temperature did not permit direct measurement of the prior austenitic texture. In fact, when the "ideal orientations'' associated with well-known fcc rolling textures were converted, alone or in combination, to martensite according to the Kur-djumov-Sachs (K-s)' or Nishiyama8 relations, the agreement obtained with the observed martensite texture was only fair at best. Recently a pertinent aspect of the austenite to martensite transformation was reported by Bokros and parker,10 who found that certain habit-plane variants of martensite were suppressed by tensile deformation of Fe-31.7 Ni single crystals prior to the necessary subzero cooling. It might be anticipated that the consequences of such preferred transformation are sustained during the formation of martensite in warm-worked austenite that has a well-developed deformation texture. The present investigation was undertaken first to establish more firmly the relation between preferred orientations in plastically deformed austenite and in the resulting martensite, and second to examine the textures for evidence of deformation-induced preferred transformation. EXPERIMENTAL PROCEDURES An alloy containing 0.3 pct C, 12 pct Cr, 6 pct Ni, and the balance iron, was selected because the mar-tensite-start temperature (M,) of about -100°C allowed convenient experimental manipulation of either austenite or martensite at room temperature. Furthermore, this composition can be readily deformed as metastable austenite at moderately elevated temperatures without intervention of appreciable isothermal or athermal decomposition products. The alloy was austenitized at 1150°C, aircooled to 510°C, rolled unidirectionally at this temperature to 93 pct reduction of cross-sectional area, and finally oil-quenched to room temperature. Partial transformation to martensite was accomplished by quenching to -196°C as needed. The rolled stock was reduced in thickness from 0.067 to 0.010 in. by etching in a solution of 5 pct HC1, 45 pct HNO3, and 50 pct water, and further thinned by careful mechanical polishing to maintain the two sides of the sheet parallel within 0.0003 in. After mechanical polishing to 0.005 in., electropolishing in 1:9 perchloric-acetic acid solution produced a final thickness of 0.002 in. The preferred orientations were determined from

Jan 1, 1968

Another excellent Swedish underground crushing plant is that at Crusher Station 51 of LKAB in Kiruna, Sweden. Bottom-dump rail cars pass over a dump scroll to discharge magnetite ore into a 288 cu yd (220 m3) pocket equipped with a Hewitt Robins E-13 vibrating grizzly feeder. The grizzly section is 59 in. (1500 mm) long and has bar spacings 3 in. (76 mm) wide. Any oversize boulders which will not pass the chute opening to the feeder are blasted. The primary breaker is a Morgardshammar overhead eccentric 55 in. by 71 in. (1400 by 1800 mm) jaw crusher powered by a 200 hp (149 kw) motor. An open side setting of 10. 8 to 11. 8 in (275 to 300 mm) accounts for the high capacity of this crushing unit (2760 stph or 2500 mtph). This figure compares favorably with the capacity of many gyratory crushers but is typical of the Swedish jaw crushing installations, which are often followed by three more stages of crushing or by autogenous grinding. Crushed ore from the jaw crusher is combined with the grizzly under- size in the crushed ore pocket and is fed by a second vibrating grizzly feeder to the secondary cone crusher. Both crushers are serviced by 50/5 ton overhead bridge cranes. During maintenance operations air -operated gates shut off the flow of ore from the dump and primary crushed ore pockets.

Jan 1, 1978

(Members are urged to send in for this column any notes of interest; concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period Nov. .10, 19 16 to Dec. 1.0, 1916: Chester Atkinson, La Fundicion, Peru. , Paul Llewellyn, East Chicago, Ind. F. J. Brule, Toronto, Ont., Canada. Harry March, London, England. Sterling H. Bunnell, New York, N. Y. E. P. Mathewson, Toronto, Ont., Canada. G. H. Cunningham, Hobart, Tasmania.' E. W. Moore, Budapest, Rumania. Courtenay DeKalb, Tucson, Ariz. W. J. Pentland, Guadalajara, Mex., E. H. Dickenson, New Y.. Heinrich Ries, Ithaca, N. Y. E. B. Durham, Mount Kisco, N. Y. W. E. Saunders, Philadelphia, Pa. L. B. Eames, Pueblo. Colo. J. G. Scrugham, Reno, Nev. N: H. Emmons, 2d, Copperhill, Tens. - W. H, Seagrave, Kennecott, .Alaska. R. E. Hoffman, Hannibal Mo.'s H. B. Small, Magangue, Colombia. B. B. Hood, Chronic, N. J. W. H. Staver, Washington, D. C. H. E. Jackman, Rochester, N. Y. R. K. Stockwell, Santiago, Chile. F. H. Jackson, Joplin, Mo. Warren D. Thompson, Boston, Mass. Knight S. Jordan, Provo. Utah. Thor Warner, Kingman, Ariz. William Kelly, Vulcan, Mich. S. T. Wellman, Cleveland, Ohio. W. H. Lanagan, San Francisco. Cal. F. H. Willcox, Pittsburgh, Pa. H. H. Lauer, Northampton, Pa. Arthur K. Adams has been appointed geologist to the Andes Copper Co.

Jan 1, 1917

By W. M. Corse

AT THE TURN of the century the nonferrous alloy industry was awakening to the value of scientific metallurgy, and brass foundries and rolling mills began to establish their own research laboratories for scientific research and control. As the industry grew and its scope broadened it became apparent that an organization was needed that would stand in the same relation to the nonferrous industry as the American Foundrymen's Association did to the iron foundry business. The brass founders' group of the foundrymen's association discussed the matter and it was finally decided to appoint a com- mittee to draw up a constitution for a new organization to be known as the American Brass Founders' Association. Charles J. Caley was chairman and Dr. Richard Moldenke secretary of this committee. The object of the organization as defined by the constitution was the study of the technological development of alloying and founding non- ferrous metals, and furthering the advance of nonferrous metallurgy and the standardization of materials and operations in cooperation with the Bureau of Standards and engineering societies.

Jan 1, 1932

By F. J. Plecity, J. T. Michalak, W. C. Leslie

W. M. Williams (McGill University)-The authors are to be congratulated on completing this detailed investigation of recrystallization behavior. The present writer has recently completed some research at the University of Toronto on the recrystallization and grain growth behavior of a number of "pure" irons, and he would like to take issue with the authors' contention that recrystallization cannot be followed by means of hardness measurements. Two series of specimens of Ferrovac E, a com- mercially available iron, were annealed to complete recrystallization at 525" and 620" C, measurements being made both of Rockwell hardness and of volume percent recrystallized as a function of annealing time. Good correlation was found between these two quantities and, following the earlier practice of Cook and Richards for copper, hardness measurements were used in an extensive investigation of recrystallization. No anomalous behavior was observed as a result of this practice. Specimens which showed complete softening always showed, (metallographically and by X-rays), completely re-crystallized structures. These observations do not, of course, detract in the least from the results of the work under discus-

Jan 1, 1962

By W. W. Stephen, J. P. Walsted, W. J. Kroll

FOR the production of carbides, various furnace types are available, especially those using arc, resistance, and high-frequency heating. Selection of a specific means of heating depends primarily on the material to be treated and the physical properties of the carbide produced. In the present case, zirconium carbide had to be prepared on an industrial scale as a raw material for the production of anhydrous zirconium chloride. Considering that a rather expensive pure oxide was to be used, the arc-furnace treatment recommended for zircon sands in a previous publication' was ruled out because of the considerable volatilization and dust losses caused by the blast of the arc. For this reason, either high-frequency or resistance heating seemed to offer more promise. Since there was not enough capacity of the former available, resistance heating was chosen. It was first thought that the Acheson silicon carbide furnace would be suitable for the present purpose, but the voltage in such a furnace, in which the current passes through the batch, varies from 220 to 75 v from the start to the end of a run. This variation is so great that a special tap transformer would have been required. Trouble was also expected by local melting of the carbide. Pure zirconium carbide melts at about 3527°C, but the melting point is brought down to 2427°C, according to Agte,2 when an excess of 6 pct C is present in the carbide. This we found confirmed by experiments in a high-frequency furnace. Excess carbon is needed in the batch to obtain a complete reduction. Fusion of the charge would cause great difficulties in an Acheson-type furnace because of the good electrical conductivity of the carbide as compared with that of the loose batch. Also, fused carbide is much more difficult to chlorinate than the spongy product that can be made in the radiation furnace described below. It was apparent that, to obtain a good-qual-ity zirconium carbide, the heat input would have to be well-controlled. The hairpin-resistor principle seemed to offer possibilities in this regard, and a furnace of this type was therefore developed. The advantages of the hairpin-resistor radiation principle have been discussed in previous publications, and a split-tube graphite-resistor furnace," now increasingly used in various laboratories, as well as a centrifugal quartz melting furnace4 of this type, has demonstrated the usefulness of this heating method. The hairpin-heater element has the following definite advantages over a straight resistor of the type used, for instance, by Georges:5 Its resistance is four times greater; it can expand freely; it is sturdier because of the larger diameter, and it has a larger radiation surface; there are no hot contacts that might wear out or overheat; only one clamp is used which permits assembling all electrical leads at one side of the furnace, making the other sides easily accessible to the operator. The shorter element and its larger diameter permit greater concentration of heat. The furnace developed is shown in fig. 1. The box (I), made of 2 1/2-in. graphite plates, has inside dimensions of 23x17x16 in. It contains the briquet-ted batch (2). The box is embedded in lampblack (3) up to the cover plate. The cover plate contains an opening for the gas escape (4) and for the observation hole (5), which permits measuring the temperature with an optical pyrometer. The cover plate is embedded in charcoal (6). The lampblack is contained in the insulating brick lining (7), held in the 1/4-in. sheet steel box (8). The graphite box is set on two rows of triangular graphite bars (9). The hairpin-heater element (10), the dimensions of which are given below the main drawing, extends horizontally in the graphite chamber and radiates freely on the batch. A graphite tube (11) keeps the lampblack from falling into the slot. The split electrode, which in reality is turned 90" against the drawing, is so arranged that the slot is vertical. The water-cooled packing gland (12) is insulated by an airgap from the heater element. A thin pipe (13)

Jan 1, 1951

[†AARONSON, ALFRED E., Vice-Pres., Mid-Co. Petroleum Co., Mid-Co. Bldg. Tulsa, Okla. '18 ABADIE, EMILE R., Min. Engr Address wanted. '76 ¦ABADILLA, QUIRICO A. Geol. Dept. Cia. Mexicans de Petroleo "El Aguila," S. A., Edifico "El Aguila," Esq., Calles Aurora y Comercio,] [ ]

Jan 1, 1925

CONTENTS PAGE ZAPFFE, CARL.-Manganiferous Iron Ores of the Cuyuna District, Minnesota. Discussed by A. K. Knickerbocker 1 MCCORMACK, C. P.-Economics of the Cuyuna Manganiferous Iron Ores. Dis-cussed by T. L. Joseph, J. Wilbur Van Evera, C. P. Perin, T. T. Read, L. E. Ives 4 READ, T. T.-Probable Error in Blast-furnace Records and Calculations Therefrom. Discussed by C. H. Herty, Jr., T. T. Read, T. L. Joseph, Ralph H. Sweetser 8 SCHWARTZ, H. A. and HIRD, (Mrs.) ANNA NICHOLSON.-Chemical Equilibria During Solidification and Cooling of White Cast Iron. Discussed by N. B. Pilling, Ralph H. Sweetser, H. M. Boylston, Albert Sauveur 10 HERTY, C. H., JR., BELYEA, A. R., BURKHART, E. H., and MILLER, C. C.-Some Factors Affecting the Elimination of Sulfur in the Basic Open-hearth Process. Discussed by Henry D. Hibbard, L. F. Reinartz,. C. H. Herty, Jr., Ancel St. John, A. L. Feild, C. R. Hayward, Ralph H. Sweetser, C. D. King, Haakon Styri, George A. Orrok 12 HIBBARD, HENRY D.-Finishing Melting Temperatures of Simple Ingot Steels. Discussed by Haakon Styri, George V. Luerssen, A. G. Zimermann, A. L. Feild, George A. Orrok, Albert Sauveur, R. F. Harrington, Henry D. Hibbard, I. A. Billiar, William J. Priestley, H. W. Gillett, W. P. Barba, Jerome Strauss, Harry H. Smith, H. LeChatelier, L. F. Reinartz 19 HERTY, C. H., JR., and TRUE, O. S.-The Reaction between Manganese and Iron Sulfide. Discussed by A. L. Field, H. S. Rawdon, C. H. Herty, Jr., T. L. Joseph, Haakon Styri 37 KAMURA, HEIHACHi.-Reduction of Iron Ores by Carbon Monoxide. Discussed by T. L. Joseph, R. Franchot, Ralph H. Sweetser, C. H. Herty, Jr 43 JOSEPH, T. L.-Effect of Sulfur on Blast-furnace Process. Discussed by R. Franchot, C. A. Meissner, T. L. Joseph, C. H. Herty, Jr., Ralph H. Sweetser, I. E. Waechter, F. N. Speller, T. T. Read 45 GOOSTRAY, JOB, HARRINGTON, R. F., and HOSMER, M. A.-Brief History of Metallurgical Practice in Cannon-making with Particular Reference to the Cast-iron Gun. Discussed by A. G. Zimermann, Geo. A. Orrok, Chas. Me-Knight, Jr., F. Brauer 51 Manganiferous Iron Ores of the Cuyuna District, Minnesota Discussion of the paper of CARL ZAPFFE, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1390-I, with MINING AND METALLURGY, December, 1924. A. K. KNICKERBOCKER,* Virginia, Minn. (written discussion).¬The author makes a broad distinction between the "black" ores (the

Jan 6, 1925

By J. E. Dutrizac, R. J. C. MacDonald, T. R. lngraham

When sintered disks of synthetic chalcopyrite (CuFeS2) were leached in acidified aqueous solutions of ferric sulfate, the following reaction stoichiometry was obtained: CuFeS2 + 2Fe2(SO4)3 = CuSO4 + 5FeSO4 + 2S Over the temperature range from 50º to 94ºC, the reaction displayed parabolic kinetics. The parabolic rate constant for the dissolution of copper is given by the equation: log.k(mg2/cm4-hr)= 11.850 - 3780/T The activation energy for the dissolution process is 17 ± 3 kcal per mole. The parabolic kinetics have been attributed to the progressive thickening of a sulfur film on the surface of the chalcopyrite. When the leaching solutions contain less than 0.01 molar Fe+3 , the Fe concentration influences the rate of leaching, probably through a mechanism involving the diffusion of ferric sulfate through the sulfur layer. At higher Fe+3 concentrations, the rate control in the leaching. reaction has been attributed to the diffusion of ferrous sulfate through the sulfur. The rate of reaction is insensitive to changes in acid concentration and in disk rotation speed. ThE reaction of acidic ferric sulfate solutions with various sulfide minerals is of practical interest for both bacterial and heap leaching. This leaching medium is generally used with low-grade ores that cannot be treated profitably by conventional means. In both bacterial leaching1-3 and heap leaching, the active agent for sulfide dissolution is ferric sulfate. Although the reactions of ferric sulfate with chalcocite, covellite, and bornite have been investigated,4*7 the kinetics of leaching chalcopyrite with ferric sulfate have not been thoroughly studied. This paper reports a study of that reaction. EXPERIMENTAL Reagent-grade sulfur was purified by the method of Bacon and FanelliB and then it was vacuum-distilled to remove any soluble magnesium salts that had been introduced during the purification procedure.9 From stoichiometric quantities of the purified sulfur and hydrogen-reduced electrolytic copper sheet (99.90 pct Cu), CuS was synthesized at 450°C in a vacuum-sealed, pyrex vessel. About 24 hr was required for the completion of the reaction. A similar procedure involving hydrogen-reduced iron wire (99.90 pct Fe) was used to synthesize FeS1.002. A 2-furnace arrangement was required. The iron was heated to 800°C while the sulfur was maintained at about 400°C. Although the reaction to consume the sulfur was rapid, the material required additional heating (1 week) in a sealed silica ampoule at 800°C before it was homogenized. X-ray powder diffraction analysis confirmed that the copper sulfide was covellite and that the iron sulfide was troilite. The composition of the iron mineral was confirmed by wet chemical analysis. The two sulfides were ground to minus 100 mesh, weighed in equimolar amounts, mixed thoroughly, and pressed into pellets at 80,000 psi. The pellets were vacuum-sealed in pyrex ampoules and then sintered for 3 days at 550°C after an initial heating at 450°C for a few hours. The pellets were then cooled, polished with 3/0 emery paper, rinsed in acetone, and stored. The material had the characteristic brassy color of chalcopyrite and was shown by X-ray diffraction to be CuFeS2. Microscopic examination of the polished surfaces revealed small inclusions of pyrite (approximately 0.5 vol pct) as the only impurity. The presence of small amounts of a second iron compound will not alter the amount of dissolved copper but might increase the amount of ferrous ion slightly. It was calculated that dissolution of all of the pyrite and 100 mg of Cu (a typical value) would change the expected ferrous concentration by only 4 pct. Microscopic examination of a pellet after leaching revealed that the pyrite was not preferentially solubilized; only those pyrite grains at the surface were attacked. Hence, the pyrite is unlikely to alter the rate of copper dissolution. The chalcopyrite disks were about 1.7 mm thick and 27 mm in diam. They were about 80 pct of theoretical density, and for this reason their true reaction area was somewhat larger than the 5.8 sq cm area presented by the polished face. The disks were cemented to lucite cylinders in such a way that only the polished face was exposed. The disks were then leached by methods previously described.6,7 RESULTS AND DISCUSSION Stoichiometry and Kinetics. The initial experiments were directed to the problem of resolving the stoichiometry of the leaching reaction. Disks of CuFeS2 were leached at 80°C for various periods of time in acidified ferric sulfate solutions that were protected from oxidation by a cover of flowing nitrogen. When the disks had been partly leached, they were removed, their soluble salts were washed out, and then they were treated with CS2 in a Soxhlet extraction apparatus. The ratio of elemental sulfur to dissolved copper thus obtained was approximately 2 to 1. After the extraction of elemental sulfur from the pellet, the residue consisted of unreacted chalcopyrite only. For runs in which an appreciable amount of copper was dissolved, the ratio of ferrous ion to cupric ion in the solution was

Jan 1, 1970