Search Documents

By David A. Thomas, John F. Peck

Fibrous microstructures and their development have been studied by metallography and by hardness and quantitative metallographic measurements. Thin, curved grains were observed in transverse sections of commercial tungsten wire and were developed in laboratory-drawn iron wire at reductions greater than about 70 pct. The unusual grain shapes are attributed to the nonuniform mode of deformation of the grains associated with the characteristic [I101 preferred orientation that develops in bcc metals during drawing. Transverse sections of heavily swaged iron wire showed a ospiral nebulao structure that appears to result from the elliptical shape of the cross section of the swaging dies and their rotary motion. Hardness and quantitative metallographic results show unusual trends that parallel the changes in microstructure. Other phenomena are considwed in light of the results, including the strength of fine wires of bcc metals, ocylindricalo textures, and the ductility of fibrous tungsten. 1 HE microstructure of tungsten wire in a longitudinal section shows grains highly elongated in the working direction, giving the appearance of a bundle of parallel fibers, Fig. l(a). Wires of tungsten and other bcc metals show a pronounced preferred orientation in which a [I101 direction is parallel to the wire axis.l The microstructure and texture of tungsten develop during warm working (working above room temperature but below the recrystallization temperature) into wire by swaging and drawing. Fibrous tungsten so produced has limited but useful room-temperature ductility, whereas annealed tungsten is brittle at room temperature. During an investigation of the effect of recovery annealing on the substructure of commerical 0.030 in. diam tungsten wire, it was found that transverse sections of the as-received material showed thin, curved grains, Fig. 1(b), instead of the expected equiaxed grains. The fact that Figs. l(a) and (b) show different sections of the same material at the same magnification is at first disconcerting, because the long dimension of the curved grains in the transverse section is several times the average fiber width in the longitudinal section. However, a longitudinal section cuts most of the curved grains across their narrow dimension, giving the appearance of a multitude of narrow fibers. On the other hand, the plane of a longitudinal section occasionally includes a long dimension of a curved grain, resulting in a broad ofibero, such as A in Fig. l(a). EXPERIMENTS AND RESULTS To investigate the origin of fibrous microstructures and particularly the unusual transverse-section structure of tungsten, rods of iron (also bcc) were drawn and swaged in the laboratory. One rod of annealed Ferrovac E was drawn in six steps to a total reduction in area of 87 pct (0.10 to 0.036 in. diam), and a second rod was swaged to the same reduction, using approximately the same reduction steps. Longitudinal and transverse sections of the swaged and drawn iron wires are shown in Fig. 2, for reductions in area of 39, 73, and 87 pct. A fibrous microstructure in longitudinal section is first evident at 73 pct reduction, and it is further developed at 87 pct reduction. The grains in transverse section remain equiaxed until about 73 pct reduction, when they become somewhat elongated and curved. At 87 pct reduction, the drawn wire shows thin, curved grains in the transverse section, similar to those observed in tungsten. The transverse sections of the iron wires swaged 83 and 87 pct reduction in area show the striking ospiral nebulao structure in Fig. 2(d). This struc-

Jan 1, 1962

By Geo. W. Bain

PRODUCERS of building stone have had to seek new and attractive uses for their output to supplement the diminished orders for standard products. Lunar is the direct result of the need of new outlets for marble and is. probably the most ingenious and attractive type to reach the market in a quarter of a century. It is a highly translucent stone which retains the same glistening sparkle in transmitted light that marble exhibits by incident rays. This sparkle sets it apart entirely from translucencies made of glass or even onyx, alabaster, and the distinctive exceedingly fine textured calcite marbles produced in Alabama and quarried formerly in northern Vermont and Quebec.

Jan 1, 1936

Jan 1, 1925

The Institute maintains a dual relationship with students: (1) an individual relationship with a Student Associate; and (2) a relationship with local organizations of students, known as Affiliated Student Societies or Student Chapters. 1. The conditions of Student Associateship are set forth in Section 8, .Article 1 of the By-laws of the Institute (see p. 45 and following pages) During 1934, sundry amendments were made for the purpose of improving the student relationship. Post-graduate students are now eligible; and the associateship can be maintained, with the payment of the regular dues of $2 per gear, for 18 months following graduation in June. A Student Associate is given a subscription to MINING A ND METALLURGY: he is accorded the privilege of getting special publications such as "The Porphyry Coppers" and "Ore Deposits of the Western States" at the reduced prices applicable to Members; he has the privileges of the Engineering Societies Employment Service and the Engineering Societies Library; and he is not only invited but urged to attend all meetings of the Institute, its Divisions and its Local Sections. The Institute wants to extend the hand of professional fellowship to students following mineral industries curricula.

Jan 1, 1936

The pressure of the gas in equilibrium with sphalerite has been determined in the temperature range of 680' to 825°C, using the Knudsen orifice method. A comparison of these experimental pressures with those calculated from thermal data and from other equilibrium measurements shows that the vapor above sphalerite is predominantly dissociated ZnS. Equations have been given for correctly calculating dissociation pressures using the Knudsen orifice method. It has been shown that the experimentally determined pressure is the same, whether the zinc sulphide is sphalerite or not, or a mixture of wurtzite and sphalerite. CONFLICTING points of view appear in the literature on the constitution of the vapor in equilibrium with solid zinc sulphide in the vicinity of 800°C. By comparing the dissociation pressure calculated from thermodynamic data and the vapor-pressure determination of ZnS by Veselovski,1 Lumsden2 has concluded that the vapor consists largely of dissociated ZnS. Sen Gupta,' however, concludes from his spectroscopic determinations that the vapor is largely ZnS molecules. In view of the fact that the thermodynamically calculated' dissociation pressure is higher than that experimentally measured by Veselovski, it seemed in order to repeat Veselovski's measurements. Experimental Procedure The method used for the determination of the pressures in this papel- is the Knudsen effusion cell. The apparatus and procedure were described in a previous paper- from this laboratory on the determination of the vapor pressure of silver. The only difference is that the Knudsen cell in this work is made from platinum and there is no external cover around the cell. The cell is an ordinary platinum crucible of 2.2 cm top diameter with a capsule cover. It was thought that platinum might stand up at these temperatures to the solid and gaseous ZnS, since it was found that the weight of the platinum cell itself did not change appreciably on heating ZnS in it at the working temperatures. To insure that reaction of the zinc sulphide with the cell was not giving' a false value, a stabilized zirconia cell was employed for check runs. Fig. 1 shows the comparison, which is satisfactory. Veselovski previously had measured the vapor pressure of ZnS using a silica Knudsen effusion cell. On repeating his experiment in this laboratory, it was found that ZnS at-tacked the silica cell, giving it a marked frosty appearance. This led to the belief that Veselovski's result:; may be in error. Also, he was operating at pressures above the range ordinarily considered safe for the Knudsen method. The effusion rate was measured by weighing the cell before and after each run. The weight loss during heating to temperature and cooling down was measured and subtracted from the weight loss during the actual run. The zinc sulphide used in this investigation was from two sources: Fisher cp grade, and a sample of pure sphalerite supplied by Mr. E. A. Anderson of the New Jersey Zinc Co. Before and after the series of runs with Fisher ZnS, X-ray analysis showed that both wurtzite and sphalerite were present. However, the ratio of sphalerite to wurtzite increased. All measurements were made below the transition temperature which has been reported" to be 1020°C. The data obtained in this investigation are tabulated in Table I. The pressure was calculated by the usual Knudsen formula" on the assumption that ZnS molecules were effusing. From these data, using pure sphalerite in the platinum Knudsen cell, the vapor pressure of ZnS, in mm of Hg, as a function of temperature is given by the solid line in Fig. 1. The best straight line, as determined by the method of least squares, is given by 14405 logpzns =-14405/T +11.032. A comparison of these results with Veselovski's shows that his results are about 50 pct lower. Discussion The vapor in equilibrium with solid zinc sulphide in the temperature range of this study will consist of Zn, S2, and ZnS mol, since other species of zinc and sulphur' are relatively unstable. The question to be settled is whether or not ZnS is largely dissociated. The derivation8 which follows gives the method of calculating the pressure of zinc and sulphur over solid ZnS, assuming complete dissociation, from Knudsen cell data. The free energy of the reaction 2 ZnS(solid) ? 2 Zn(gas) + S2(gas) is given by ?F?° = -RT In K = —RT In p12p2 where p1 is the zinc pressure and p is the sulphur pressure. If dissociation occurs in a closed system,

Jan 1, 1955

AS provided in Article VIII, Section 4 of the By- laws, the Papers and Publications Committee has formulated the following, rules of pro-cedure and submitted them to the Board of Directors for consideration and approval. In preparing these rules the committee, and an active subcommittee con-sisting of Messrs. Norris, Sharpless; Fohs and Wither-ell, have kept in mind the desirability of codifying the practice that has grown up through the now sev-eral years of experience of the committtee, without casting them in a mold so rigid as to be hampering. The problems of the Institute change from year to year and the methods of publication must change also to meet each new situation as it arises. "The estab-lishment of divisions and special volumes devoted to the papers. read before each required certain changes from former practice. These rules have been framed with this in view. The committee suggested, however, in its letter of transmittal, that the system will be made all the more workable if the Board will, as far as practicable, in making appointments to this committee, arrange for representation from each of the professional divisions and technical committees. It is understood that the chairman of the committee will be named by the Board. The rules regarding spe-cial volumes have been framed, keeping in mind the present policy of distribution, as already approved by the Directors under which the special volumes go only to the special. groups except on request. The committee has not attempted to provide rules governing consideration of any appeal made to the Board from one of its decisions, but its services and files will necessarily be at the full service of the Board in any such event. The rules which were ap-proved by the Board at its meeting on March 30, 1928, are as follows: Signed by C. S. Witherell, Chairman. (A) The authority of. the Committee on Papers and Pub-lications, hereinafter called the Committee, is defined in Art. VIII, Sec. 4 of the By-laws of the Institute, which reads as follows: "Papers and Publications: The Committee on Papers and Publications shall consist of the Secretary of the Institute, and at least twelve members of the Institute, to assist in passing on all papers offered for publication. They shall be appointed annually by the Board of Direc-tors, on recommendation of the President, and shall have authority, subject to appeal to the Board, to accept or reject papers for publication in the Transactions and Technical Publications of the Institute. The Commit-tee shall formulate a set of rules of procedure which, when approved by the Board, shall have the force of By-laws until revoked or amended." The policy of the Committee will be to uphold the ob-jects of -the Institute as set forth in the Constitution (Arti-cle 1, Sec. 2).

Jan 5, 1928

By Forbes Rickard

Gilpin County, the cradle of mining in Colorado and the Cornwall of North America, is too well known to need much introduction; get, for the benefit of those not familiar with the district, it may be well to premise that it comprises a tract of country of about 122 square miles, lying between the counties of Jefferson, Boulder and Clear Creek, and hounded on the west by the main range of the Colorado Rockies. It is located centrally in the State, 40 miles west from the city of Denver. During the 38 years since the first gold-discovery, Gilpin county has contributed about eighty million dollars in gold and silver to the world's supply of these metals. Many mining districts have had their rise and decline in half this time; but, very far from being exhausted, this mining district is still in the ascendant; its output is increasing (it was $3,600,000 for the year just closed), and it was never more prosperous nor productive than to-day. Taken generally, there does not exist anywhere in the world so great a number of permanent veins within so small an area as in this district. Gilpin is practically a " poor man's camp." Its veins, with few exceptions, outcrop at the surface. In the oarlier---days of the camp these outcrops were worked in many instances by sluice-mining; particularly is this the case with regard to the veins of the Russell gulch. Discoveries are still made in the heart of this district, and the productive area is every year extending its limits. The districts of Yankee Hill, Hawkeye and Pine Creek, which used to be isolated, are now part and portion of the one gold-field of Gilpin county. Within the last year sensationally rich gold-discoveries have

Jan 1, 1899

By C. T. Eddy, R. W. Drier

The conductivity of copper wire is of prime importance to the electrical industry and consequently to the copper refiner and wire manufacturer. Annealed copper wire has a higher conductivity than hard-drawn wire, but, on the other hand, its tensile strength is lower. In an attempt to explain the reasons for these changes in properry. or at least to study the conditions existing in these two types of copper wire, the experiments described here were carried on in the Department of Metallurgy of the Michigan College of Mining and Technology This is only a partial and preliminary report on some of the work done to date on a research program of which the object is an intensive study of copper. It is offered with the hope that, though it is not an exposition of the most rigorous of conclusions, the general trend of inferences which may be drawn will be of value and interest. Effect of Direction of Drawing In 1928 some work was done on hard-drawn copper wires to determine whether wire drawn in a continuous machine (that is, all in one direction) would have a different structure from wire that had a reversal in direction at some stage of the drawing process. The diffraction spectra obtained indicated that as the position of the wire rayed approached the core, a preferential crystal orientation existed, and that the closer to the core the more preferred was the orientation. The data obtained partly corroborated the work done by Schmidt and Wassermanl and by Clark.2 Samples Used in Following Investigation The samples selected for use in both the diffraction work and the resistivity measurements were taken from Nos. 6, 8, 10 and 12 gage

Jan 1, 1930

By R. T. Hukki

IT is no great exaggeration to say that present grinding practice and economics are largely determined by lining design. A record of outstanding liner wear can be achieved with any liner surface pattern that will positively lock the outer layer or layers of grinding media. With no slippage, lining wear is bound to be slight. At the same time, popular practice calls for tumbling loads of about 50 pct of mill volume to obtain maximum grinding capacity. Innumerable parallel grinding investigations have verified that optimum speed for such a mill lies within 70 to 85 pct of theoretical critical speed. If the mill is speeded up to 100 pct of critical, little or no grinding can be accomplished. Earlier Work on Supercritical Grinding: First investigations concerning grinding at supercritical speeds seem to be very old. Remarkable work on the subject has been performed by White,&apos; and his experiments have been described and summarized by Richards.&apos; White&apos;s contributions seem to have passed unnoticed by Fahrenwald,2,3 whose extensive experiments have been well presented, yet apparently very little appreciated. Additional work on grinding at supercritical speed has been reported, e.g., by Lewenson and Tscherny,&apos; USSR; Anselm and Grunder,&apos;, Germany: and Rose and Evans." Great Britain. Subcritical and Supercritical Speeds: In the formula of the critical speed given in the textbooks of mineral dressing, no factor indicating the coefficient of friction is generally included. If this factor = 1.0, which is equivalent to grinding conditions in a mill provided with heavily ribbed lining, the formula of the critical speed holds as such and grinding is possible at subcritical speeds only. In a mill equipped with a smooth or relatively smooth lining, the numerical value of the friction factor in the denominator of the formula becomes <1.0, indicating that grinding at supercritical speeds should be possible in such mills. It has been recently shown by the author&apos; that a wide supercritical speed range will become available for grinding—and especially for fine grinding—if the basic conditions within the mill have been selected properly. Mathematical analysis of mill dynamics at supercritical speeds&apos; has indicated that the mill speed may be increased if: 1) total mass of grinding medium decreases, 2) mass of the individual grinding piece increases, and 3) the coefficient of friction between the outer layer of medium and the mill lining decreases. It is obvious that the mass of the individual grinding piece will be affected by its shape and by its specific gravity. The coefficient of friction decreases with: 1) increasing smoothness of liner surface, 2) increasing roundness of the grinding piece, 3) increasing fineness of material to be ground, 4) decreasing pulp density, and 5) decreasing hardness (abrasiveness) of the mineral to be ground. In a mill equipped with heavily ribbed lining, practically no size reduction will take place between the lining and the outer layer of tumbling medium, because slippage is prevented. In the overwhelming majority of today&apos;s mills the grinding accomplished is by virtue of cataracting and/or cascading media with some action within the tumbling charge. Sub-critical speeds only can be applied. In grate-type or peripheral discharge mills equipped with a smooth lining a tumbling load of any kind of common medium occupying about 50 pct of mill volume will behave in such a way that practically no slippage will take place. This has been verified in experiments run by the author in the laboratory and in pilot plant mills&apos; equipped with smooth lining. Again, the operation is limited to the subcritical range. In a mill with a smooth lining, grinding will be possible either at subcritical speeds or within a wide supercritical speed range as soon as the basic requirements for a desired speed are fulfilled. In a mill operated at supercritical speed, any point on the liner surface proceeds at a speed greater than that indicated by the formula of the critical speed, while any grinding piece situated in the outer layer of the medium against the lining proceeds in the same direction at a speed less than that indicated by the critical speed. This speed difference produces a very effective attrition grinding zone between the liner surface and the outer layer of the medium. The share of attrition grinding of the total grinding accomplished increases rapidly with increasing speed in the supercritical speed range. The smooth surface of the mill lining may be well illustrated by the surface of a bucking board. The outer ball layer may be similarly represented by the lower surface of a muller. If the bucking board, the material to be ground, and the muller all proceed in the same direction at the same speed, no grinding will result. This is the general situation in the mills of today. If, however, the muller is pulled with respect to the board, moving or stationary, grinding will be accomplished effectively. Although grinding in today&apos;s mills is primarily the result of cataracting and/or cascading media, the principal place of grinding at high supercritical speeds will be the attrition zone.&apos; In the mineral dressing laboratory of the State Institute for Technical Research. Helsinki, Finland, large quantities of different ores have been ground in a pilot plant ball mill (3x3 ft) at a top speed about 230 pct of the critical. With the same mill, theoretical investigations concerning the grinding characteristics of ball mills equipped with a smooth lining have been carried out up to the speed of 313 pct&apos; of the critical. With a smaller mill, the grinding characteristics with a variety of grinding media have been investigated at speeds up to 2000 pct of the

Jan 1, 1959

By Ralph H. Sweetser

AT the end of 1943 the charcoal pig iron capacity of the United States was at the lowest point in over 1110 years, with only one strictly charcoal blast furnace in operation, and all others permanently out of blast except one in Tennessee d reported to he running on part charcoal and part coke. Such a decrease in production has taken place in spite of the O.P A.&apos;s high-premium price on charcoal pig iron of +34 per ton f.o.b. furnace in Michigan. Depletion of the hardwood supply within fifty mlles or inure of the blast furnace is the reason why; the deplorable lack of reforesting is the cause.

Jan 1, 1944

THERE are three chief production zones of tungsten ore in China. In the Province of Kiangsi mines are located at Kanchow, East River, and West River. Their combined production is understood to amount to 300 to 350 tons of ore per month, and their original exportation is made through the port of Kiukiang, largely to Shanghai. The second zone is in Kwangtung Province, the mines there being at Tayulin. Produc-tion reaches about 200 tons per month and cargo is gen-erally exported through the port of Hong Kong. In the Province of Hunan approximately 25 tons of ore are produced monthly in the mines at Ton-on. Tungsten ore from Kiangsi and Kwangtung Prov-inces is generally about 70 per cent WO, (tungstic acid), while that from Hunan is of lower quality, run-ning about 65 per cent WO3. Kiangsi ore is received from the mines in 100-1b. and Hunan in 224-lb. gunny sacks. No repacking is done except as it is made neces-sary by the condition of the sacks. Kiangsi Province contains the Chinese districts pro-ducing the largest amount of salable wolframite or tungsten. Many districts west and south of Kiangsi have been found to have wolframite deposits.-Com-merce Reports.

Jan 1, 1928

By R. J. Cowan

In the art of cementation a controversy has been going on for years as to whether solid or gaseous carbon is the active agent in carburizing steel. More recently opinion has crystallized into a compromise to the effect that carburizing is a gaseous cementation of steel in the presence of solid carbon. The importance of this theory has a particular bearing upon the work to be described. In the art of carburizing, use is commonly made of such words as &apos;&apos; Catalytic" "atomic," "nascent" and "activated," in an attempt to describe the process. These words are used indiscriminately. For instance, the gas is said to be "catalytic" and carbon to be "nascent," or vice versa. In using these expressions, investigators are confirming the acceptance in their minds of the active conditions of both gas and carbon in the cementation process. Reactions at Metal Surfaces For many years attention has been directed to the consideration of reactions that occur on metal surfaces. When heated under the influence of certain metals a complex gas will be broken down and one of the constituents thereof usually found to be very active chemically in combining with the metal. The process of nitriding is an example of this type of reaction. In this case ammonia (NH3) breaks down at the metal surface and the nitrogen which is thus liberated reacts with the surface to form a nitride whereas molecular nitrogen not so liberated is inert and will not react chemically with the metal. Whatever term or terms may be used to describe such reactions, the fact remains that they are highly important and valuable in their commercial applications. Since the metal surface plays so important a part in these reactions, it is evident that any accumulation of reaction products thereon interferes seriously with the progress of the reactions. For this reason it is desirable to remove all such products as rapidly as they are formed in order to bring active gas into contact with the surface and thus facilitate the desired reactions. This is accomplished best by conducting the operation in a continuous manner, thereby causing the reacting gases to pass over the

Jan 1, 1931

ALABAMA. Aldrich, Aldrich, W. F. Anmston, Noble, A. E Bessemen, Abbott, C E, Fergusson, V Birmingham, Aldrich, T. H, Aldrich, T. H, Jr, Bowron, J, Burbidge, T A, Collord, G L, Crockard, F H, Davis, F H, Dimmick, F. D., Hiller, E., Johnson, G R, Ludwig, C P., McCormack, G B., McCrery, Peters, R , Jr , Phillips, W B, Ramsay, E ,Shook, A. M Car bon Hall, Pill, J R Emsley, Williams, E P Gadsden, Hudson, J B , Helena, Squire, J Holt, Shook, J W. Huntnnlle, Moss Lehigh, Toulmin. Rock Run, Garvin, J. M. Sheffield, Miller, D I Tusscaloosa, McCausland, E J , Woodward, Woodward, A. H

Jan 1, 1910

By L. W. Bahney

FREQUENTLY in using a thermo-electric pyrometer for measuring the temperature of a furnace, a hole is drilled at the back or side of the furnace, through which is introduced the tube containing the thermo-couple. At times the couple is left almost where it drops, for the reason that it soon becomes too hot to be handled easily, and the space at the back or side of the furnace may be so small and uncomfortably hot that an easy and accurate adjustment is nearly impossible. In order to overcome this clumsy and unscientific method of using the thermo-electric pyrometer, I designed an adjustable stand, to hold the clay or quartz tube unclosing the platinum and plati-num-rhodium leads that constitute the couple of the Le Chatelier thermo-electric pyrometer. This stand also allows an easy and rapid adjustment of position to varying heights and angles, as may be desired for special reading. This stand is illustrated in Fig. 1. The couple in the tube might be of better service if the tube were held a little higher above the charge in a roasting-dish, changing the height and angle if desired. The stand, made of 1.5-in, water-pipe and mounted on casters, is heavy enough so it cannot be tipped over easily. It is adjusted to any position, and has a universal clamp which holds the clay or quartz protecting-tube. To avoid disturbing the wires of the couple at the cold junction each time the tube is moved, the cooling-bottle sets in a wire basket so placed that it moves forward or back with the couple. To overcome the necessity of leveling and adjusting a galvanometer at each furnace, a switch-board is used to connect

Jan 1, 1910

By H. J. Levinstein, H. J. Guggenheim

RbFeF3 is a transparent ferromagnet with a large faraday rotation which permits the direct observation of magnetic domain structures in bulk crystals. If the position of dislocations within the crystal were known a study of domain wall dislocation interactions would be possible. In this paper an etch pitting solution is described which gives a one-one correspondent between the etch pits and the dislocations intersecting the (100) surfaces of RbFeF3 crystals. In addition, RbFeF3 is shown to have sufficient plasticity so that known arrays of dislocaticms can be put into the crystal. It is concluded that RbFeF, is an ideal material for the investigation of domain wall dislocation interactions. THE influence of lattice defects on the motion of domain walls in ferromagnetic materials has been studied extensively both theoretically and experimentally.4 The experimental data obtained has been qualitative in nature due to the lack either of a quantitative knowledge of the magnetic domain array in the material or of the nature of the dislocation configuration in the material. At room temperature RbFeFJ has the cubic perovskite structure. It is ferromagnetic below 86°K.5,6 It is also transparent and has a large faraday rotation in the magnetic state.7 The domain structure of this material is observable in three dimensions in crystals which are millimeters in thickness.&apos; Since RbFeF3 satisfies the requirements of having an easily visible three-dimensional magnetic domain structure, it was of interest to determine if the dislocation structure of the material could be determined and if the material was sufficiently plastic so that dislocations could be introduced into the as grown crystals. This is a report of the results of that investigation. EXPERIMENTAL PROCEDURE The crystals of RbFeFs used in this experiment were grown by a technique described elsewhere.5 In order to obtain flat strain-free surfaces, the samples were first cut to the crystal orientation desired and the surfaces were polished by employing standard metallographic techniques. The samples were then immersed in a solution of 1 to 3 g of KOH in 100 ml of water. This solution removes the damaged surface layers uniformly leaving a film on the surface of the sample. Etch pits are obtained by immersing the sample in an approximately 50-50 solution of 30 pct peroxide and concentrated acetic acid. The film formed during the KOH treatment turns deep red in color in the etching solution and flakes off the sample. The etching time required depends upon the pit size desired and

Jan 1, 1970

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman. PERCY E. BARBOUR, Vice-Chairman. A. D. BEERS, Secretary, 55 Wall St., New York, N. Y. C. A. BOHN, Treasurer. Boston Meets first Monday of each winter month. W. E. C. EUSTIS, Chairman. R. L. AGASSIZ, Vice-Chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Boston, Mass. ALBERT SAUVEUR, H. L. SMYTH. Columbia Holds four sessions during year. Annual meeting in September or October. STANLY A. EASTON, Chairman. FREDERIC KEFFER. Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON. FRANK A. ROSS.

Jan 10, 1916

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman. PERCY E. BARBOUR, Vice-Chairman. A. D. BEERS, Secretary. 55 Wall St., New York, N. Y. C. A. BOHN, Treasurer. Boston Meets first Monday, of each winter month. W. E. C. EUSTIS, Chairman. R. L. AGASSIZ, Vice-Chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Boston, Mass. ALBERT SAUVEUR, H. L. SMYTH. Columbia Holds four sessions during year. Annual meeting in September or October. STANLY A. EASTON, Chairman. FREDERIC KEFFER, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON, FRANK A. ROSS.

Jan 9, 1916

By G. Sachs, L. J. Ebert, W. F. Brown

INTRODUCTION ISOTHERMAL transformation, or "austempering," of a carbon-containing austenite at elevated temperatures yields so-called "intermediate products." Their structure and properties are, for a given hardness, rather different from those of "tempered martensite" obtained on conventional quenching and tempering.1 Several investigators2,3 have found that for high carbon and slightly alloyed steels the intermediate products formed at temperatures close to that of the martensite reaction possess strength properties superior to those of tempered martensite. The structure of these low temperature, intermediate products is generally acicular (bainite) but clearly different from that of martensite. However, at higher austempering temperatures, between 1000 and 1300°F (540 and 700°C) carbon steels were found to exhibit a rather low ductility.4-5 Thus notch bar tensile tests showed the ratio between notch strength and regular tensile strength to decrease with increasing austempering temperature. For ductilities below a few percent this notch strength ratio is a measure of ductility, according to investigations on low alloy steels.6-7 Furthermore the presence of intermediate products formed unintentionally on quenching was considered as responsible for the low ductility and impact energy of some heat treated steels.8 These intermediate products could result from partial transformation at the so-called "nose-temperature" where the rate of the transformation is a maximum. Tempering improved such mixtures of martensite and intermediate products, their properties approaching those of tempered martensite of equal hardness. The following investigation constitutes an attempt to determine certain strength properties of a partially austempered and subsequently quenched low alloy steel, namely, a chromium steel (SAE 5140). The structures formed by such a treatment should consist of a mixture of intermediate products formed on austempering and a martensite formed on oil quenching from the austempering temperature. It was intended, by varying the austempering time, to vary the quantity of the intermediate products between zero and 100 pct. The austempering temperature of 860°F was selected after extensive preliminary tests close to the nose-temperature. Austempering at this temperature yielded an acicular intermediate product. Additional tests under less exacting conditions were made for an austempering temperature of 950°F where the intermediate product appeared to be very fine pearlite. To determine the effects of tempering on structures containing various amounts of

Jan 1, 1948

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman. PERCY E. BARBOUR, Vice-chairman. A. D. BEERS, Secretary. 55 Wall St. New York, N. Y. C. A. BOHN, Treasurer. Boston Meets first Monday of each winter month. W. E. C. EUSTIS. Chairman. R. L. AGASSIZ, Vice-chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Boston Mass ALBERT SAUVEUR, H. L. SMYTH Columbia Holds four sessions during year. Annual meeting in September or October. STANLY A. EASTON Chairman. FREDERIC KEFFER, Vice-chairman: LYNDON K. ARMSTRONG, Secretary-Treasurer, P. 0. Drawer 2154, Spokane. Wash. D. C. LIVINGSTON, FRANK A. ROSS.

Jan 8, 1916

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman. PERCY E. BARBOUR, Vice-Chairman. A. D. BEERS, Secretary, 55 Wall St., Now York, N. Y. C. A. BOHN, Treasurer. Boston Meets first Monday of each winter month. W. E. C. EUSTIS. Chairman. R. L. AGASSIZ, Vice-Chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Boston, Mass. ALBERT SAUVEUR, H. L. SMYTH. Columbia Holds four sessions during year. Annualmeeting in September or October. STANLY A. EASTON,- Chairman FREDERIC KEFFER,-Vice-Chairman: LYNDON K. ARMSTRONG, Secretary-Treasurer, P.O. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON, FRANK A. ROSS.

Jan 10, 1916