Search Documents

By Clinton H. Crane

IN October, 1925, J. R. Finlay delivered an address entitled, "The Future Price of Lead." Lead was then selling at 8.85c. and Mr. Finlay and most of the rest of us were concerned about the shortage. Now, a little more than six years after, lead is selling for 3.55c., and nobody is worrying about the difficulty of getting plenty of it. For 1931 the U. S. G. S. reports United States produc¬tion as 390,000 tons of recoverable lead in ore. Our estimate is slightly higher than this; nearer 400,000 tons. This is the smallest production since 1911 and 1912, but in spite of this, stocks for the year-have increased nearly 50,000 tons. Our estimate for the production outside the United States is 1,120,000 tons, or more than double the production of either 1920 or 1921, and 30 per cent more than in 1913. Stocks abroad probably have not increased more than stocks in the United States. In other words, foreign consumption is double what it was in 1.920-21, whereas domestic consumption is substantially less. It looks as if Mr. Krueger, president of the Swedish match trust, was right when he said that "This country had better stop worrying about Europe and think a little bit more about its own affairs."

Jan 1, 1932

By Thomas T. Read

THE benefits derived from stabilization of industry that might possibly be attained through some scheme of centralized economic planning have been much discussed of recent months, and opinions on the subject range from those who believe that some agency like the War Industries Board would be practicable to create and wholly beneficial in effects, to those who are equally convinced that none of the suggestions so far advanced are at all practicable, or likely to be productive of more of good than of evil. The discussion has been on the general topic, but-many of those who have written or spoken on it have introduced economic problems of the pinera1 industry; for example, Newton D. Baker, who referred to the coal industry in his address on economic planning at the Williamstown Institute of Politics on July 31, and then went on to say, "Industrial progress is made by the development of new things, but new things upset the equilibrium of any plan. Who could have planned the industrial effects of the development of the railroads, or the economic changes which you have seen attend the development of the internal combustion engine. Obviously, unless we are prepared to put world economics in a strait-jacket and, like the encyclopedists, write its full history on the theory that further progress is impossible, no such plan could be made for nations which are forging ahead as is entirely rational for nations which are still catching up."

Jan 1, 1931

By Ovid W. Eshbach

ENGINEERING education has been powerfully affected by the impact of war, just how powerfully can be better understood after considering the postwar problems regarding students, staff, and plant. In time of war no one will question the necessity of expediency of military training. With the cessation of hostilities, expediency gives way to the evolutionary process of strengthening engineering education as need is exemplified by experience. During the war, except for the Navy V-12 program, engineering education was at its lowest ebb of the century. Freshman enrollments were largely limited to those graduating from high school at the age of seventeen; and the upperclass, to those disqualified for active service. In most schools the experienced staff was either in service or government and industrial research. Many may never return to their former occupations. The most immediate problem is that of maintaining and building a staff to meet the enrollment of returning veterans. It is estimated that out of the eleven

Jan 1, 1945

By W. E. Coughlin, R. L. Faverty, F. H. Lightner

The intent of this paper is to present the general strategy and method of implementation to achieve a "fast-track" mine development. The major objectives of a "fast-track or rapid development schedule are to minimize front-end development expenditures and to realize an early cash flow from operations. The Borealis project of Houston International Minerals Corp. (HIMCO) is used as the working example to illustrate the development schedule. Borealis is a 2.9 kt/d (2,500 stpd) gold-silver heap leach operation near Hawthorne, NV.

Jan 1, 1984

By Robert C. Collins, Clifford L. Jewett

The development and production of artificially colored roofing granules have been key factors in the success of the asphalt roofing industry. They provide protection for the asphalt from solar radiation and satisfy the home-owner's desire for a wide range of attractive colors. As a result, the asphalt shingle has become the most commonly used roofing material today. In addition to providing a stimulus to the asphalt roofing industry, artificial methods of coloring granules completely changed the nature of granule production from one of quarrying, crushing, and screening to a complex technical operation. Today's roofing granules are the result of many years of research, and they are produced in modern plants to exact specifications. History Asphalt roofing materials available today are the product of a long evolution of technological development. Forerunners of the present bituminous products, appearing as early as 1780, were primitive constructions of burlap saturated with crude tar or pitch. An early improvement to this basic effort was the dusting of talc, mica, or other finely ground material on the coated surfaces to keep the roofing from sticking to itself in storage. At times some pigmentation was added with the dusting material for initial color, but this was far from satisfactory. In fact, this early product possessed none of the qualifications of a good roof surfacing material. It was not economical; it was difficult to handle and apply; it was not attractive; it provided no resistance to fire; and it would not withstand the elements as well as other products then in use. Methods and machines were soon devised to saturate endless webs of felt with asphalt from the fast-growing petroleum industry. Even though saturated felt became available, this product of rags and wood fiber had almost the same limitations as burlap and tar. Even with heavier coatings of asphalt applied to both sides of the sheet for rigidity and longer life, the product still lacked color and fire resistance. Further, it was found that constant exposure to the sun soon caused the asphalt to become brittle, and it eventually cracked and leaked. This led to the first important use for crushed mineral products on asphalt-coated shingles and provided the key to the subsequent growth of the asphalt roofing industry. When a layer of crushed mineral was embedded in the surface exposed to the weather, the asphalt coating was protected from ultraviolet light and retained its elasticity over a much longer period of time. In addition to this protection, the mineral surfacing provided some resistance to fire. Fire resistance in the past had been found only in the expensive slate or tile roofs and the unattractive and expensive metal roof coverings which were then available. The most common mineral granule applied to the early asphalt roofing products as they began to make their first significant advances after 1900 was screened waste from slate quarries. Slate granules being available in dull shades of red, green, black, purple and a few other miscellaneous colors did provide a degree of color. Since slate has a flat platelike cleavage, it provides a cheap protective cover for the asphalt-coated sheets. Records show that coarse slate screenings were used for asphalt roofing as early as 1906. As the asphalt roofing industry developed, many other natural colored rocks and minerals were used to coat the surfaces of the roofing. The list included silica

Jan 1, 1975

By J. M. Hassler

NOWHERE can there be found a more misleading statement than the old one that "Iron can be manufactured cheaper in the South." During the past decade ironmakers and users of iron have heard varied and sundry stories of the wonderful resources of the Birmingham district, including abundant ore and coal fields, cheap labor, a wonderful climate and similar industrial Utopian statements. Birmingham represents the major portion of the iron business in the South, acid as Birmingham fares so goes the iron business of the South. The intent of this paper is to shed some light on the actual conditions surrounding ironmaking in the South, especially in the Birmingham, or North Alabama, district. By a presentation of facts it is desired to point out that the "cheap iron" of the industrial South is a thing of the past, primarily because of increased labor cost and because labor is radically different in performance to what it was years ago. Also, because most of the raw materials needed in ironmaking that would be classed better than inferior are gone.

Jan 1, 1937

By W. A. Goodyear

It is safe to assert that in cities generally, the fuel of the future for all domestic, as well as for most manufacturing and metallurgical purposes, will be gaseous fuel. The immense advantages which gas possesses in facility and cheapness of distribution, cleanliness, and economy of manipulation, and the facilities which it offers for utilizing in almost all cases a much higher percentage of the total quantity of heat produced, than it is possible to do with any kind of solid fuel, are facts which will vastly more than compensate for the comparatively small loss of heating power, which will be found necessary in the turning of the solid fuel into gas upon a large scale, and which, in the bpinion of the writer, will, at no distant day, command attention, and will ultimately result in a revolution in our use of fuel. The employment of gaseous fuel upon a scale of any considerable magnitude, has hitherto been almost entirely confined to the utilization of the waste gases of the iron smelting furnace for heating the blast, and the rapidly increasing use, for certain metallurgical pur-

Jan 1, 1883

By Oliver Bowles

THE ADVERSE CONDITIONS that have gripped industry during recent years have to some extent submerged technical developments under the more pressing demands of economic problems. Progressive operators, nevertheless, have given attention to improvements in processes and equipment even when sales were at a low ebb. The array of facts relating to technical advancement here presented, although doubtless incomplete, is sufficient to indicate that the spirit of inquiry and research has not been quenched by adversity. During the latter part of 1933 a new element has focused interest more fully on improved methods of quarrying, mining, and preparation of nonmetallic minerals. Codes established under the NRA have fixed minimum wages, reduced working hours, and tended to establish selling prices .on a basis of reasonable profit. Labor adjustments will in many instances increase the cost of production, and stabilization of selling prices will tend to emphasize quality and service rather than price as sales arguments. These new conditions point to a growing necessity for improving technique in the interest of reducing cost of production and improving the quality of products. Thus, technology is linked with economics more firmly than ever.

Jan 1, 1934

By T. R. A. Davey

A Survey of current and recent research and developmental work is supplemented by predictions for processes which should be developed over the reminder of this century.

Jan 1, 1970

By B. P. Nutter, M. Lebourg, J. A. McAlister

The Multi-Flow Evaluator (MFE) is a new system of tools providing an original approach in drill-stem testing. It improves control during the testing operation and gives a more accurate evaluation of the fluid recovered while providing additional pressure information for reservoir analysis. The tools are operated entirely by up and down motion of the drill stem. This up and down operation provides a positive means of control and offers easily observed surface indications of tool operating position. An unlimited number of shut-in and flow periods may be taken with this tool while in the hole. The key to the success of the MFE system of tools is the safety seal packer. Until this development, operation of the tools by up and down motion only had proven unreliable. The success ratio of the MFE now exceeds the ratio achieved by conventional tools. The equipment includes a 2,750-cc chamber in which a representative sample of the flowing formation fluid is trapped at the end of the last flow period and brought to the surface under pressure. The sample can be evaluated at the wellsite or transferred under pressure for laboratory analysis. The sampling feature of the tool allows a sample to be obtained from a reservoir which has suffered minimum influence from production. A representative sample can be obtained for laboratory or empirical analysis by employing a testing technique to minimize drawdown during flow periods. Interpretation methods to take advantage of this additional information are presented and supported by actual field examples. INTRODUCTlON The Multi-Flow Evaluator (MFE) represents the most recent technical advance in formation testing. Drill-stem testing techniques prior to the MFE have been limited in three areas—(1) operaiion, (2) recovery analysis, and (3) reservoir analysis. The tools in the MFE system allow maximum control during testing and provide test information superior to that obtainable with conventional tools. The system of tools and the operation procedures are described to illustrate the mechanical advantages over present tools. Methods of pressure build-up and fluid

Jan 1, 1966

By E. F. Johnson, V. O. Naumann, D. P. Bossler

A method is presented for calculating individual gas and oil or water and oil relative permeabilities from data obtained during a gas drive or a waterflood experiment performed on a linear porous body. The method has been tested and found both rapid and reliable for normal-sized core samples. INTRODUCTION Individual oil and gas or oil and water relative permeabilities are required for a number of reservoir engineering applications. Chief among these is the evaluation of oil displacement under conditions where gravitational effects are significant, such as a water drive or crestal gas injection in a steeply dipping oil reservoir. Numerous proposed methods of obtaining relative permeability data on reservoir core samples have been too tedious and time consuming for practical use, or have yielded questionable and sometimes inconsistent results. A method has been developed by which the individual relative permeability curves can be calculated from data collected during a displacement test. The method is based on sound theoretical considerations. Using this method, with a properly designed experimental procedure, relative permeability curves can be obtained using core samples of normal size (i.e., 2 to 3 in. in length and 1 to 2 in. in diameter) within a few days after receipt of the core. In a recent publication D. A. Efros1 describes an approach to the calculation of individual relative permeabilities that is based on the same theoretical considerations. We believe the approach described in the present paper is more adaptable to practical application than the method implied by Efros. In addition, comparisons with independently determined relative permeabilities are furnished to substantiate the reliability of the new method. DERIVATION Previously the theory of Buckley and Leverett as extended by Welge2 as been used to calculate the ratio of relative permeabilities. In the derivation which follows, this theory is further extended to permit calculation of the individual relative permeabilities. The theory assumes two conditions which must be achieved before the method is applicable. They are that the flow velocity be high enough to achieve what has been termed stabilized displacement,3 and that the flow velocity is constant at all cross sections of the linear porous body. In stabilized displacement the flowing pressure gradient is high compared with the capillary pressure difference between the flowing phases. The high pressure drop insures that the portion of the core in which capillary effects predominate will be compressed to a negligibly small fraction of the total pore space. The assumption of constant flow velocity at all

By S. A. Swensrud

NINETEEN Thirty-Six was the biggest year in volume in the history of the oil industry, and unquestionably the best since 1929 in respect to profits. The quota of new and difficult problems to face seemed a little smaller during 1936 than in most recent years, and a somewhat better balance existed between the different branches of the industry. 'Domestic consumption of gasoline in 1936, estimated at about 475 million barrels-the highest on record, was approximately 11 per cent above 1935, and 26 per cent above 1929. Demand for crude oil increased in about the same proportion: over 1935, and the average production, of about three million barrels daily,' constituted a new high level.

Jan 1, 1937

By Arthur E. Focke

IF a metallurgist employed in an industry producing mechanical parts or assemblies wishes to make the most of his opportunities he will be concerned with every use of metals in that industry. He will not only take part in the testing and treating of the metals used but will assist in their selection and study their behavior in processing and in service. In addition, he will attempt to develop an understanding of the problems involved in the use of the metals in all plant tools and equipment. Metallurgists that follow this course will soon recognize that frequently too little thought is given to the effect of the design of parts on the way the metal in them is expected to behave in service. He will come to realize that changes in the design of a part will often be much more useful than changes in the hardness, strength, composition, or structure of the metals used in them. Does this mean that a metallurgist is out of place in these industries and that he should leave the field to others or be content to fill only a minor role?

Jan 1, 1947

By R. E. Morgan, D. L. Douglass

The determination of phase relationships and solid-solubility limits can be performed by quantitative metallography in addition to the usual X-ray and metallographic techniques. For example, Beck and smith1 redetermined the ß/ß + ?, ß + ?/?, a/a + ß and a + ß/ß boundaries in the Cu-Zn system by measuring the volume fraction of second phase of several alloys and extrapolating the volume fraction-composition curves to 0 and 100 pct. A modification of this technique is suggested for certain alloy systems, in which it is not necessary to use several alloy compositions but merely one. A single two-phase alloy may be used to determine terminal solubilities in the following manner. The method consists of equilibrating samples of the alloy in a two-phase region adjacent to the desired solid solution, at three or more temperatures, quenching, measuring the volume fraction of second phase present, and applying an analytical treatment to calculate the unknown solid solution. However, two restrictions are inherent in this technique. They are: 1) only certain types of alloy systems are amenable to it, and 2) the general features of the system must be known. The first drawback to the new technique, i.e., that only certain types of systems may be studied, necessitates that the composition at one end of the tieline must either be constant with temperature or well established as a function of temperature. Either a pure metal or some intermetallic compounds fulfill the former. If it is assumed that the volume per gram-atom of a dilute solution is unchanged by the addition of element B to element A, the composition of the solid solution in equilibrium with the second phase may be determined by a material balance and is given by where X, = volume fraction of B in a solid solution Xc = volume fraction of B in compound c X = volume fraction of B in alloy f = volume fraction of second phase The composition by weight may then be determined by the use of tables in the Metals Handbook2 when the density ratio of the solid solution constituents is known. A possible alternative treatment involving the use of the lever rule is less precise than the above tech- nique. This may be used when the density of the solid solution is either known or may be calculated from X-ray data for several compositions. The following analysis is then made. The ratio of compound to solid solution (by weight) may be expressed as follows: x0 - x wc = xr-x = x0 - x r2i Xc -X where Wc = weight of compound w = weight of solid solution x, - alloy composition, weight percent x = unknown composition Xe = compound composition but where V, = volume of compound VA = volume of solid solution pc = density of compound p, = density of solid solution fc = volume fraction of compound fB = volume fraction of solid solution and fs = l -fc then If pc and xc are known, and f, is measured, then pB is the only unknown on the right side of Eq. [4]. The known densities of the solid solution can be plotted for various compositions and can then be expressed mathematically as a function of composition. The use of an expression of pB = f(x)reduces the equation to one unknown—the desired solubility. In the event that the densities are unknown, they may be calculated for various compositions from Vegard&apos;s law. The calculated values are then plotted and expressed analytically. The most accurate results are obtained for Eq. [4] when fc<< 1, i.c., when (x, -x,) - 0, &/l-f, - m; but as fc/l -fc - 0, (xl-x,)- (x, - x), and x - x,,. However, the accuracy with which fc can be measured decreases as f, decreases.3 Alloys for investigation must be selected by a compromise, which is based upon an error analysis of Eq. [4] and knowledge of the accuracy of volume fraction measurements. An examination of phase diagrams in the literature showed many which were amenable to the technique described here. The zirconium-copper system was selected in order to determine the solubility of copper in beta zirconium. Pieces of an alloy which was arc-melted three times were wrapped in tantalum foil and sealed under an argon atmosphere in Vycor tubes. The sealed samples were equilibrated at temperatures from 850" to 960°C for 3 weeks and quenched to room temperature by smashing the capsule in water. Several planes of polish were examined, and

Jan 1, 1960

By Lawrence Adler

MINE hoist ropes have hitherto been selected by successive approximation, a process both tedious and inexact. The proposed expression is a readily solved synthesis of existing data and the following standard equation:&apos; [ W + Wr + (W + Wr) -a 9 (W + W)f + b] n=T [1] For convenience, a glossary of all terms appears on page 564. Since rope weight (W,) and bending load (B) are functions of unit rope weight (Wv), which in turn is a function of rope strength (T), W, and B can be expressed in terms of T. W, as a Function of T: A study of the curve in Fig. 1, unit rope weight vs strength, yields Eq. 2: W. = -f- [2] Therefore Wr = WvL = T. [3] iv B as a Function of T: From Fig. 2, unit rope weight vs diameter, Eq. 4 is obtained: W, = 1.6d2 [4] B is related2 to d and D, and d has been expressed in terms of W, by Eq. 4, so the curve B vs W, (Fig. 3) gives Eq. 5: 177,000 177,000 This may readily be checked from the expression3 for a 6x19 rope, i.e., d3 B = 288,000D Since d2 = 0.625 W, and N = substituting d into the above expression gives Ea. 6: 180,000 180,000 B T, which will be used. [6] Into Eq. 1 substitute Eq. 3 and Eq. 6, noting that f=0.02: W + T 1.02+=T. [7]

Jan 1, 1958

By C. R. Kuzell

IN COMPARISON with recent years 1932 has yielded much less tangible evidence of progress in copper reduction and refining. The industry has been extremely quiet, especially in the United States. Design and construction has been throttled by lack of new capital expenditures. The excess producing capacity of the whole industry and the extremely gloomy outlook for the future have made it unwise to tie up more capital except under special conditions. The plants built during the previous year have, however, been placed in operation. Older plants have been abandoned, temporarily shut down, placed on part time operating basis, or continue to operate at a low percentage of normal capacity. In the United States the Phelps Dodge Corporation at Douglas, Ariz., has completed the remodeling of the former Calumet & Arizona smelter. A new roaster and Cottrell plant chimney was completed this year. Though operations have been limited the new equipment has been found to justify all expectations. The reverberatory plant addition consists of two furnaces 26 by 107 ft. inside dimensions, with a high arch, and modern steel binding of excellent design. Natural gas fuel gives good results. One of these furnaces will treat 1000 tons of solid charge per day with a fuel consumption of approximately 3,000,000 B.t.u. per ton. The larger converters have not only yielded the expected lower costs, but have simplified operations in the converter department. One of the noticeable results is the greater cleanliness in the environment and the absence

Jan 1, 1933

By Milnor Roberts

WAR struck the mineral industry of Washington with cross currents that produced a peculiar result. The State&apos;s production of coal, industrial minerals, and metals for 1941, valued at $28,507,282, was increased in 1942 under war pressure to approximately $35.000,000. Meanwhile a tremendous demand had arisen for men to construct airfields and many other large projects for the Army and Navy in Washington and Alaska, and Government plants for the mineral industry costing $140,000,000 or more, as well as a call for employees in the U. S. Navy Yard at Bremerton, the sixty shipyards, the four Boeing airplane factories with many auxiliary shops, and hundreds of other plants turning out war materials. In spite of an influx of nearly 300,000 people, causing an increase of 17.1 percent in the population since 1940, according to the Census Bureau, the State clearly is still engaged in an unusual amount of war production in proportion to its population. A large proportion of the workers have been drawn from the mineral industry to the war plants, whether through motives of patriotism, high wages, or, in the Boeing plants at least, the glamour of the operation

Jan 1, 1944

By V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pet natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pet of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 11 a in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F.

Jan 1, 1949

By Harry Tufft

FOR many years the treatment of mine timbers with preservatives was confined to a few pioneer plants in the United States, and it is only in the past few years that the practice has grown appreciably. In a field study of the mine timber situation in Illinois, Pennsylvania, and further study of the situation in the country as a whole, I found that most mine operators did not keep records on mine timber that would afford the necessary data for determining the possible savings from preservative treatment. Some primary questions the mining engineer should be able to answer before making his decision on preservative treatment. for a particular mine are: (1) Quantity and cost of timber going into permanent workings annually; (2) quantity and cost of annual replacements due to decay; (3) life of untreated timber in different places; (4) desired life of timber. With the necessary facts in hand, he can then con-fidently select a method of treatment and preservative that is best suited to his needs. In former years when timber was cheap and an abundant supply could be had close at hand, as was the case in the majority of mining regions, the mine op-erator did not concern himself much except to see that enough was supplied to keep the workings safe. The cost figure for timber and labor, distributed to cost per ton of ore, was all the bookkeeping necessary. With present costs of timber, labor, and increasing length of haul to the mine, many operators are paying closer attention to timbering costs and studying them in. more detail. Some of the larger and more progressive opera-tions now keep detailed&apos; figures that give information on all phases of their timber problems. However, at the majority of mines the data available do not permit such analysis. Checks as to where the different con-signments are placed, the date of setting, and the period

Jan 6, 1927

In answer to inquiries from members, Mr. Sheafer said that the culm-banks of which his paper gave the shipments were of about the average quality of the banks in the Mahanoy region of the Schuylkill field,.made prior to 1881 or 1882, when the practice of preparing buckwheat coal was introduced; but that in a very old hank, made about 1849, no coal above pea-size had been found. Apparently it was then the practice to ship everything. In reply to an inquiry concerning the utilization of the fine coaldust, Mr. Sheafer said that it was not utilized in connection with the washing described in his paper, but was carried away in the water as waste; that during Mr. Corbin&apos;s presidency the Reading Company built at Mahanoy City an extensive plant for making artificial fuel, but difficulty was encountered, due to the circumstance that the small coal from different collieries varied in its combustible quality and also in the amount of pitch required to be mixed with it, and he believed they concluded that from some varieties of the coal-dust a very good fuel could be made, but at a cost entirely too great for successful competition with cheap coal. Of course, the anthracite dust was not so well suited to this manufacture as bituminous slack. R. W. Raymond, New York City : I believe that was the practical outcome of the enterprise of a member of the Institute, Mr. E. F. Loiseau, now deceased. It was found, I think, as an additional drawback, that the manufacture of artificial compressed fuel from anthracite dust could not be successfully practiced with material so impure as that of the culm-banks. Consequently, the manufacture could be based on that source of supply only when accompanied with a preparatory washing. The most favorable location for it would be at large yards where the waste from the handling of coal, which is comparatively pure material, could be thus treated. I believe the manufacture of compressed fuel from bituminous coal was at one time a profitable business in Nova Scotia, but was destroyed by the indirect effect of the general introduction of watergas for illuminating purposes. The result of that change on the

Jan 1, 1895