Search Documents

By Fred D. Gustafson

With the postwar emergency for new housing and for new industrial buildings, much research has been done on lightweight aggregates for use in concrete and plaster. The trend toward lighter weight aggregates to relieve the dead load on the higher, steel framework buildings started toward the end of the last century. Progressively the requirements became more stringent, crushed bank slag, weighing 80 lb per cu ft as compared to 100 lb for crushed rock, was supplemented in some sections by foamed slags and expanded shales weighing from 40 to 60 lb per cu ft. In other sections cinders were used weighing from 40 to 50 lb, including sand. Sections favored with more recent vulcanism turned to pumice weighing from 30 to 60 lb, whereas other localities made use of diatomite, from 28 to 40 lb. Exfoliated vermiculite weighing from only 6 to 10 lb per cu ft came into use. As the search for lighter weights in aggregates continued so did the search for other desirable properties such as nailability, ease of cutting or channeling, and good insulation to both sound and heat. This search eventually led to a widespread interest in the expansion of perlite, or similar volcanic glasses, with the result that in 1946, the Office of the Housing Expediter' listed eleven firms reporting the operation of processing plants either on pilot or commercial scale producing aggregates weighing from 2 to 16 lb per cu ft. Geology Perlite is one of the large family of rocks originating from a granitic or acidic magma and generally has a "rhyolitic composition with a marked perlitic structure."² The name "perlite" is a derivation from "perlstein" originally given "to certain glassy rocks (hyaloliparites, hyalo-rhyolites) with numerous concentric cracks, from the fancied resemblance of broken out fragments to pearls."3 The cause of the perlitic texture is somewhat controversial. Johannsen attributes the texture to strain set up in the glass by cooling and describes the finding of peculiar, glassy balls, called marekanite, more or less rounded and showing concave indentations, which may be left when perlite is broken. Frank Rutley, on the other hand, in 1881, while working on vitreous rocks from Montana, observed that there was incipient or partially started crystallization with segregation of water toward the un-crystallized portion in all specimens of perlite examined. Further he observed evidence of strain around focii of crystallization to which he ascribed the development of the spherical cracking which gives the rock its perlitic texture.4 Widespread over the western and southwestern United States where Tertiary vulcanism is exposed, perlite commonly is associated with andesitic, basaltic, and rhyolitic lavas with inter-bedded tuffs and ash of Eocene age although some deposits are associated with rocks assigned to the Pliocene age.5, 6 n nearly all cases the perlite overlies water laid tuff beds or agglomerates or breccias of explosive nature, an outstanding exception being the occurrence of perlite as the chilled selvage of andesite intrusions.7'8 Available chemical analyses of per-lites from the western and southwestern United States indicate that they are varieties of leucorhyolites rather than of normal rhyolites, leucorhyolites having less than 5 pct of dark minerals, normal rhyolites having more than 5 pct. This conforms with Johannsen's observation that leucorhyolites are the prevailing kind in North America.9 Tables 1 and 2 give

Jan 1, 1950

By Mark J. Klein

The creep of 043 was studied over the temperature range 1650" to 3200°F and over the stress range 3000 to 44,000 psi. The steady-state creep rate over this range of stress and temperature can be expressed by the equation where A is a constant, is the stress, and is -0.8 x 103 psi-'. Over a narrow range of stress variations c0 a and for this proportionality n varies from 3 to 30 in accordance with the relation n = aB. Above about 2400° F, H, the apparent activation energy for creep, is 110,000 cal per mole, a value about equal to that estimated for self-diffusion in this alloy. Below 2400°F, H increases with decreasing temperature reaching a value of -125,000 cal per mole at 1700° F. In this temperature region, H appears to be a function of the interstitial concentration of the alloy. MOST of the detailed creep studies of dispersion strengthened metals have been concerned with metals having fcc structures. However, there are a number of important refractory alloys with bcc structures that derive part of their high temperature strength from an interstitial phase and whose creep behavior has not been well defined. This paper describes the creep behavior of the bcc alloy, D43, over the temperature range 1650" to 3200°F (0.4 to 0.7 Thm) and over the stress range 3000 to 44,000 psi. In addition to colum-bium, this alloy contains 10 pct W. 1 pct Zr, and sufficient carbon (-0.1 pct) to form a carbide dispersion throughout the matrix of the alloy. The effects of variations in temperature and stress on the steady-state creep rate of this alloy are presented in this paper. EXPERIMENTAL PROCEDURES Creep tests were made in a vacuum of 106 torr under constant tensile stress conditions using a Full-man-type lever arm.' Creep specimens were machined from 0.020-in. D43 sheet (grain size -5 x l0-4 in.) processed in a duplex condition (solution annealed -2900°F, 40 pct reduction in area, aged 2600°F). The specimens were tested in this condition without further heat treatment. Specimen extensions over 1-in. gage lengths were continuously recorded using a high temperature strain gage extensometer. Differential temperature and stress measurements were used to determine temperature and stress dependencies of the creep rate. Activation energies were calculated from the changes in strain rate induced by abrupt shifts in the temperature during constant stress creep tests. The 100°F temperature shifts used in most of the activation energy determinations required 15 to 90 sec depending upon the temperature at which the shift was made. The dependence of strain rate on stress was determined by measuring the change in strain rate for incremental stress reductions during constant temperature tests. It has been shown that columbium-base alloys such as D43 are susceptible to contamination by gaseous interstitial elements during vacuum heat treatments.' In this regard, it is unlikely that these alloys can be heat treated without some loss or gain of interstitial elements despite the precautions taken to control the heat treating environment. However, several factors suggest that changes in interstitial concentrations of the specimens during testing did not affect the results presented in this paper. First, the dependence of the creep rate on the stress or temperature determined during the course of a single creep test showed no variations with the duration of the test. A variation would be expected if a loss or gain in interstitial concentration during the course of the test affected results. In addition, precautions taken during this investigation to minimize interstitial contamination by wrapping the gage lengths of the specimens with various foils2 (Mo, Ta, W) did not produce a detectable change in the stress and temperature dependencies relative to the unwrapped specimens. The averages of duplicate analyses for carbon and oxygen in several specimens determined before and after creep testing are listed in Table I. The combined nitrogen and hydrogen concentrations which were ordinarily less than 50 ppm did not change in a detectable way with creep testing. The analyses show that only minor changes in carbon concentration occurred during creep testing except for specimen 4. This specimen which was tested at 3100°F lost a significant amount of its carbon concentration to the vacuum environment. Specimen 1 gained 100 ppm of O, while specimens 2, 3, and 4, which were tested at progressively higher temperatures, lost increasing portions of their initial oxygen concentrations during testing. RESULTS AND DISCUSSION The Temperature Dependence of the Creep Rate. The apparent activation energy for creep, H, was de-rived from creep curves similar to that shown in Fig. 1. Steady-state creep was rapidly attained at the beginning of the test and with each change in temperature. This behavior suggests that the alloy rapidly attains a stable structure with each shift in temperature or that the structure is constant throughout the test. Since the dispersion will tend to stabilize the structure, the latter is probably the case. The activation energy was found to be independent of the direction of the temperature shift and the magnitude of the shift (50" or 100°F). Although H was approximately independent of the strain, there was a tendency for it

Jan 1, 1970

By G. B. Gould, F. M. Gibson

IN DECEMBER, 1934, the joint Committee on Fuel Values, of the American Institute of Minim and Metallurgical Engineers and the American Society of Mechanical Engineers, submitted a preliminary report, which briefly stated its conclusion that it was not possible to devise any formula for the valuation of coal, based upon the various physical and chemical properties, that would be generally applicable. That report also listed those chemical and physical properties of coal that are generally recognized to have some effect on its use in steam plants, and those physical characteristics of steam plants which affect, in one way or another the relative importance of the properties of coal used in them. Since then, the Committee has considered and discussed in greater detail the interrelationship of the properties of coal and plant characteristics. The conclusions of the Committee are summarized below, with certain recommendations regarding engineering procedure, which will promote the collection of more easily correlated observations with respect to this subject, and thus advance more rapidly the accumulation of data capable of general application.

Jan 1, 1936

By Pablo Hadzeriga

Great Salt Lake brine was subjected, in laboratory scale, to conditions simulating solar evaporation. Solid phases and the variation in composition of the liquid phase throughout the potassium salts crystallization zone are presented. These experimental results are discussed and compare with stable equilibrium data of the quinary system Cl-, SO4, Na+, K+, Mg + + and H2O. The Great Salt Lake brine in Utah is a vast reserve of several potential chemicals which has attracted much attention in the recent past. From the standpoint of an ore reserve, it may be said that the lake contains a low grade ore which has to be concentrated by evaporation of water. Because of the fairly favorable weather conditions in the Great Salt Lake area, it seems reasonable to consider solar evaporation as an economical means of concentration. From the view of phase chemistry, the main constituents of Great Salt Lake brine make it belong to the five component system: C1-, SO4=, Na+, K+, Mg++ and H2O. Because of their low concentration, the presence of other elements may be regarded as having little effect on the equilibrium of the five main components. Equilibrium data for the quinary system of our interest has been available for many years. Using these data, it is possible to calculate how the brine of the lake will concentrate when subjected to solar evaporation. In practicing solar evaporation, the weather factor and supersaturation conditions cannot be ignored, but their introduction into calculations using equilibrium diagrams is almost an impossible task. With the experimental work presented in this paper, an attempt is made to compare the stable equilibrium data of the quinary system as applied to the case of the Great Salt Lake brine and the dynamic equilibrium when that brine is subjected to continuous solar evaporation. Sea water brine belongs to this quinary system when only the major constituents are considered. The study of this system has been carried on since the last decades of the nineteenth century. The reason for these intensive studies was to give a geological explanation to the underground potash deposits. AS a result, many theories were presented trying to relate the equilibrium data with the geological formation, paragenesis and metamorphism of these deposits. Two main approaches were followed for the equilibrium studies of this quinary system. One of them, and the best known to us, was the school started in Germany in the last century by J. H. Van't Hoff. The other one, which started about the same time, was the school of N. S. Kurnakov in Russia. Both approaches were different and as a consequence generated opposite theories about the geological formation of potash deposits. The Van't Hoff school studied the quinary system of sea water under careful laboratory control, resulting in stable phase diagrams. During these studies, Van't Hoff recognized the difficulties in crystallizing some double salts.' ". . . . we unexpectedly found that some compounds whose formation in the solutions under investigation was possible at 25°C, nevertheless totally failed to put in an appearance. These, not to mention the calcium salts, were leonite, MgSO4 . K2SO4 4 H2O; kainite, KC1-MgSO4 . 3 H2O; and kieserite, MgSO4 .H2O. Even exceedingly slow crystallization with the addition of the compounds themselves did not remove the condition of supersaturation in the case of these bodies." However, those salts (leonite, kainite, and kieserite) were included in the stable phase diagram at 25°C as shown in Fig. 1 using D'Ans data.3 The figure also shows the sequence of crystallization of the Great Salt Lake brine according to the stable diagram. In later studies by the Van't Hoff school, especially by D'Ans,3 Karsten,4 Autenrieth,5,6 attention

Jan 1, 1968

By A. S. Richardson

THE rating of a mine ventilation fan, or the characteristic curves illustrating the duty it may be expected to perform under various mine conditions are, in general, determined by the fan manufacturers. The information is of importance to the operator, or engineer, of a mine in many ways. For instance, when an increased flow of air is desired and the fan speed is to be increased, it becomes necessary to know what increase in volume may be expected and what the power requirements will be. In other cases, it may be decided to make changes in the mine to reduce the resistance to the flow of air, or to make changes in the general system of ventilation. Under any changed mine conditions there will be a difference in the duty performed by the fan. When mechanical ventilation is adopted, the factors governing the selection of equipment for the new system include not only the requirements of existing conditions, but also those that may be expected with the development of the property. Efficiency of service is required over a variable range of operating conditions. Characteristic curves, giving the duty performed by their fans under variable resistance conditions, are published by most fan manufacturers. General statements as to the effect of variation in speed of the centrifugal-type fan, under fixed mine conditions, appear in textbooks and trade catalogs. However, to the author both sources of information appear to be unreliable, at least under certain circumstances. The catalog of a leading fan manufacturer says: 1. The volume of air delivered by a fan varies directly as the speed. 2. The pressure, or water gage, produced by a fan varies as the square of the fan speed. 3. The horsepower of a fan varies as the cube of the fan speed. While these statements are accurate when the fan is operating under conditions similar to those that exist when a blower is used to force air through a pipe, they are not correct under mine conditions that are by no means unusual. Such conditions may be found in deep mines operated through shafts, in which a wide range of temperatures may be

Jan 8, 1925

By C. P. Proctor, E. D. Hummer, J. A. Younkins

COMPARATIVELY little has been published relating practical experience with the control of the solid content of washery water systems that must be "closed." A "closed" system is one that for some reason may not be cleaned by the emission of any effluent of high solid content to be replaced by clean water in order to hold the solid content of the waste water within reasonable bounds for efficient washing. It is the purpose of this paper to describe practical experience with such a water system and to present data that it is hoped may be of some use to those who are faced with a similar problem. The washery clarification system described comprises three thickeners and three filters, and although it is admitted that each of the fields of water settling and thickening and filtration offers a wide scope for investigation, the authors are not attempting to present the answers to these problems but to set down the results of some experience along these lines, making no claims as to the ultimate solution of the problems in hand. The subject of water clarification has vast ramifications; for example, the science of flocculation as applied to water settling and filtering opens up fields of wide possibilities of which as yet little is known. A comparatively recent entry into the field of water treatment, which may offer possibilities of practical application, is the use of "wetting" agents such as "Aerosol." GENERAL ARRANGEMENT OF WATER SYSTEM So that the reader may obtain a comprehensive picture of the factors concerned in the control of a closed water system, it is necessary to give a brief description of the washing plant that is serviced by the water system to be described in the following pages. As we are not primarily concerned with the washing plant in detail, only a brief description of the flow of coal as it relates to the water system will be given here. For a more detailed account of this type of washer, the reader is referred to earlier papers.1.2 The washer, which handles 0 to 4-in. raw coal (750 tons per hour) is an American Rheolaveur plant of two complements; the coarse coal or sealed discharge plant and the fine coal or free discharge plant. The sealed discharge plant (Fig. r) consists of twin 48-in. primary launders, each having two washing boxes, supplemented by one 32-in. rewash launder, which also has two washing boxes. "Push" water for washing and conveying coal in these launders is supplied from a constant-head tank under pressure head of 10 ½ ft. at the point of introduction at the feed end of the launder. This tank also supplies water for upward or vertical currents used in the Rheolaveur or washing boxes. Each box discharges into a sealed boot elevator (Fig. I).

Jan 1, 1942

By G. L. Kothny

DEVELOPMENTS of well-surveying instruments, coring and core orientation, were in an advanced state when drilling for oil began-these developments actually originated with the mining industry.1 Surveying of oil wells was not generally used in the United States until Alexander Anderson2 disclosed that the majority of wells drilled with rotary tools were crooked, with average horizontal drifts of about 516 ft. for holes 5000 ft. deep and about 793 ft. for holes 6000 ft. deep. This disclosure brought about the development of many additional instruments for surveying oil wells during the progress of drilling and after their completion. Surveying of boreholes, during the process of drilling at regular depth intervals, became a standard practice in the petroleum industry. Some producing states even established laws making check surveys mandatory, during drilling and under certain conditions also after completion. The surveying of boreholes also brought about changes and improvements in drilling practices. It provides information for the guidance of the hole while drilling, and for plotting the course as the work progresses, enabling the driller to take corrective measures immediately and with the least expense. The reasons for drilling straight holes are too well recognized to warrant any full discussion of them here. Straight holes are less costly to drill, because [ ] they reach the object on the shortest course. Table I shows the horizontal drift and loss in vertical depth for various angles of inclination. It is not surprising, therefore that many drilling contracts for oil wells today limit the drilling contractor to a maximum inclination off the vertical of 2° or 3°. In the mining industry the reasons for drilling straight holes are still more serious. A crooked hole may miss an ore body underground or provide incorrect information regarding an ore body. TYPES OF SURVEYING INSTRUMENTS The surveying instruments used in oil-well drilling may be classed in two types: I. Inclinometers, recording inclination only.

Jan 1, 1946

By Merton C. Flemings, Harold D. Brody

Analyses that include diffusion of solute in the solid phase are formulated to describe solute redistribution in dendritic solidification of metallic alloys. The analyses are based on conditions that include negligible undercooling before nucleation of solid phases, negligible increase of solute in advance of the tips of growing dendrites, complete diffusion within the liquid over distances the order of dendrite spacings, and a plate-like dendrite morphology. The classical nonequilibrium freezing equation, Cs = kCo(I - fS)k-l accurately describes solute redistribution between dendrite arms for the solidification processes considered, provided diffusion in the solid is negligible. To account for the effect of diffusion in the solid, an analytic expression is given which is similar inform to the classical expression. 172 addition, a numerical-analysis procedure is etnployed to examine in more detail the effect of diffusion both during and after solidification. The analyses are intended for application to solidification of castings and ingots to describe a) final solute distribution after solidification and cooling to room temperature (microsegregation) and b) local fraction solid as a function of ternperatcre within the solidifying casting or ingol. SOLUTE redistribution in cellular and dendritic solidification has been discussed quantitatively in recent papers'-3 and in a series of earlier work.4-6 However, none of the analyses developed have permitted close correlation of theory with final solute distribution (microsegregation) observed in castings and ingots. In this paper, discussion is given of approximations which may reasonably be made in mathematical treatment of microsegregation, and analyses are presented based on these approximations. Numerical results are given for Al-Cu alloys. In a second paper the analyses will be compared with exeriment.7 CLASSICAL ANALYSIS The classical quantitative treatment of solute redistribution within a closed "volume element" has been derived repeatedly, for example by Gulliver,4 Scheil,' and Pfann.' This "classical nonequilibrium solidification equation" is written for constant partition ratio: where Cs = interface composition of the solid when the weight-fraction solid within the "volume element" is fs (weight fraction, wt pct); k = equilibrium partition ratio; Co = initial alloy composition within the volume element (weight fraction, wt pct). Assumptions of Eq. [11 are: 1) There is negligible undercooling before nuclea-tion, or from curvature or kinetic effects. 2) There is no mass flow in or out of the volume

Jan 1, 1967

By D. G. Wilder

D.G. Wilder I found the suggestion that the amount of displacement of a fault can be numerically related to the thickness of gouge or breccia to be both intuitively satisfying and intriguing. I have long agreed that there is some type of relationship between the amount of gouge and the amount of displacement of faults. I congratulate the author for developing a numerical relationship between them. However, I am concerned that the limits for applying this relationship be fully understood. An underlying assumption in this approach is that there is either a uniform thickness of gouge or breccia along a given fault or the thickness does not vary widely. Since it is not always possible to confirm this, the displacements derived by this method should be viewed with caution unless significant fault extent can be observed. At the Nevada Test Site, in drifts constructed in granite for test emplacement of spent nuclear reactor fuel, we found a fault with 0.3 to 0.4 m (12 to 16 in.) of clay gouge. Within a few meters of this location, the fault had no clay gouge, but rather consisted of a highly fractured zone with significantly altered rock and some slickensides. Based on Fig. 1, the 0.3 to 0.4 m (12 to 16 in.) thickness of gouge would indicate a displacement in excess of 30 m (98 ft). However, no gouge thickness would indicate essentially no displacement. Based on a quartz vein that terminated on the fault, and is not identified nearby, an estimated displacement of more than a few meters was made. This estimate is consistent with that obtained using the regression line proposed in the paper if the 0.3 to 0.4 m (12 to 16 in.) thickness for the gouge is used. However, using the regression curves with zero thickness would not yield results consistent with what was observed in the field. Therefore, it is important to recognize that the suggested procedure would properly yield a range of probable displacements. ? *Work performed under the auspices of the US Department of Energy by the Lawrence Livermore National Laboratory under Contract W-7405-Eng-48. Reply by E.C. Robertson It is certainly true that the t (thickness) of gg-bx (gouge and breccia) on a fault does vary along the fault. My observations have been that near the termination of a fault, the displacement d is small and the t is also small, whereas the maximum d and t will usually be found in the central part of the fault. The information on gg-bx and t of the fault found in granite in the NTS tunnel by Mr. Wilder could be interpreted somewhat differently than he does. He speaks of the fault changing within a few meters from 0.3 to 0.4 m (12 to 16 in.) of clay gg to "a highly fractured zone with significantly altered rock and some slickensides," but no gg. The highly fractured rock may be taken to be bx, rock not so finely ground as gg but still crushed by the fault movement, equivalent to the gg in my usage, and probably occupying about the same t. Mr. Wilder's estimates for the fault in the NTS tunnel for t of 0.3 to 0.4 m (12 to 16 in.) and for d of a quartz vein, in excess of "a few meters," would place the point on the low side of the central trend line in my Fig. 1, at the lower limit. There is, of course, a problem with determining d using displacement of only one planar surface. It would be greater or lesser depending on the rake of the movement. Finally, estimating the d of a fault from its t should be made with awareness of our present uncertainties, as pointed out by Mr. Wilder. Although the central trend line in my Fig. 1 has a ratio of d/t of 100, I have put the limiting ratios at 10 and 1000. Understanding of the values of the ratio will be improved only with collection of more data, for which the discussion of Mr. Wilder is much appreciated. ? G.C. Waterman E.C. Robertson's paper provides significant information to a geologist attempting to deduce fault offset by noting the products of structural dislocation. However, considerable mapping in underground and open-pit mines, and examination of structures produced in different geological settings, have convinced me that gouge and breccia thickness are controlled by geological conditions and fault movement. The following paragraphs suggest geological variables that control them. 1. Depth of Loading A near-surface fault resulting from tensional stress has more breccia/gouge than is produced by a similar stress at considerable depth. A deep-loaded compressional stress may produce a linear zone of schist, or structural dislocation may occur along an earlier formed belt of schist. Such "shear zones" are common in Canadian mines in precambrian rocks. In neither case can offset be directly deduced by an analysis of the minimal gouge/breccia in the shistose rocks. At greater depth, stress may be partially to wholly relieved by flowage. I vividly recall first noting the regional "Midas Thrust" in the Lark mine, Bingham Mining District, UT (where we called the structure the North Fault). My recorded notes, as I remember them, showed a narrow gouge streak separated the "Jordan" and "Commercial" limestone units from impure, muddy limestone beds of uncertain stratigraphic position. The visible structure did not indicate the great importance of this premineral fault

Jan 1, 1985

By E. E. Carpenter

(San Francisco Meeting, September, 1915) BELIEVING that the results accomplished in the mill of the Churchill Milling Co., Wonder, Nev., during the fiscal year ended Sept. 30, 1914, will be of interest, I am presenting the more prominent facts and figures showing the progress made in treating this ore with especial reference to tonnage, supplies, costs, and extractions. The mill is situated at Wonder, Nev., in the Wonder mining district, 55 miles east from Fallon, Nev., the nearest railroad point. All supplies are hauled this distance by freight teams, this method of transportation having been found more reliable for continuous service than trucks, the price paid for hauling being slightly under one cent per pound. In this mill are treated the ores of the Nevada Wonder Mining Co. ,

Jan 6, 1915

Iron and Steel ALBERT SAUVEUR, Chairman. A. A. STEVENSON. Vice-Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Harvard Sq., Cambridge, Mass. GUILLIAEM AERTSEN, HENRY M. HOWE, E. GYBBON SPILSBURY, JOHN BIRKINBINE. ROBERT W. HUNT, J. 8. UNGER, WILLIAM H. BLAUVELT, J. E. JOHNSON, JR.. FELIX A. VOGEL, CHARLES A. BUCK, CHARLES KIRCHHOFF, LEONARD WALDO, ERNEST F. BURCHARD, RICHARD MOLDENKE. WILLIAM R. WALKER, FRANK D. CARNEY, CHARLES F. RAND, WILLIAM R. WEBSTER JAMES GAYLEY, JOSEPH W. RICHARD$, FREDERICK W. WOOD. HENRY D. HIBBARD, C. F. W. RYS,

Jan 1, 1917

By Kenneth M. Ritchie

Mineral wool is a term applied to man-made fibers of silicate glass with useful properties resulting from their fibrous nature. In contrast with crystalline fibrous minerals such as asbestos, mineral wool fibers are amorphous, solid filaments produced by drawing from molten liquid and subsequent cooling. Chemically they are silicate glass with varying percentages of metallic oxides, especially those of aluminum, calcium, magnesium, iron, and in glass wool, sodium, potassium and boron. Other elements such as manganese, titanium, sulfur, etc., result from their presence in the raw materials used and are not purposely added. In the United States, mineral wool is a generic term and may be applied to rock, slag or glass wool. In Europe, glass silk and silicate cotton are products in the same category, but the term mineral wool is less commonly used. Current usage is to ignore the actual source and to differentiate products on a composition basis; thus rock and slag wools have about 35-45 pct of silica, while glass wool has 54 to 60 pct. Much mineral wool of slag origin is called "rock wool," and this practice is increasing, although wool made of slag from lead or copper refining is often referred to as "lead slag wool." Its greenish-gray to greenish-black dark color, due to 5-25 pct Fe (reported as FeO), distinguishes it from "white" wools made from iron, blast furnace slag containing only 1-2 pct FeO or Fe203. Most mineral wool is used for thermal insulation against heat and cold; sound absorption and isolation are probably the next most important uses. Both its thermal and acoustic values result primarily from the physical structure of the heterogeneous mixture of fibers and air which is the form in which the fibers are first obtained and handled. For this reason, within fairly wide limits, differences in chemical composition are relatively unimportant, and for most conventional applications all types are competitive in properties and value. Mineral wool intended for extreme conditions of high temperature, acid resistance and special purposes must have a chemical composition which will insure the desired properties. This may differ greatly from that of ordinary wools; for example one product approximately 98 pct Si02 and another consisting of 50 pct A1203 and 50 pct Si02 are produced and sold for high temperature service up to 2000°F or more. These are considerably more expensive to manufacture and their cost limits their use. Historical The manufacture of mineral wool consists fundamentally of a process which subjects molten material to shear and/or tensile forces that draw them into fibers. The liquids are cooled at a rate which solidifies them quickly. As a solid glass they are technically super-cooled liquids since they have no true melting point. The drawing out of glass into thin rods, filaments and tubes was known from very early times, and present day continuous production of glass filament for textiles was evolved gradually by adapting hand methods to automatic machinery. Rock and slag wool manufacture had a somewhat different development. Early explorers reported finding filamentous material

Jan 1, 1960

J. S. UNGER,* Pittsburg, Pa, . (written discussion?).-The author of the paper has given an excellent description of the appliances used to cool parts of an open-hearth furnace, and some of the reasons why the refractories fail in service. Personally, I favor water-cooling, but to a limited degree. At one time I advocated more universal cooling than is now practised, but believe I must change my mind. Water-cooled, thin-lined blast furnaces have not proved as satisfactory as anticipated. While this may retard the building of many such furnaces, it will not prevent the use of regular tuyere- and bosh-cooling appliances. Water-cooling any furnace may be easily carried to the extreme. In an open-hearth furnace, excessive port or roof cooling, or cooling the working floors may preserve the lines of the furnace, lower the cost of refractories, acid to the comfort of the workmen, and necessitate fewer shutdowns for repairs, but it may not be good economy on account of the high first cost, the cost of cooling water, maintenance of cooling appliances, and the immediate reflection in a higher fuel cost. The question becomes a financial one, and is answered by using water-cooling devices up to the point at which they cease to show true economies. Open-hearth furnace bulkheads, roofs, and ports fail rapidly in about the order named. If they could be made to last indefinitely by water-cooling, the furnace would still have to be shut clown periodically for cleaning the slag pockets, regenerator chambers, and flues. Extra, or spare, pockets and regenerator chambers have been advocated to permit of continuous operation, but the space required, the cost of installation, and the fuel required to initially heat such cold chambers will largely prevent their adoption. Some particular fuels, as high-ash powdered coal, require frequent stoppages for cleaning, but for this particular fuel a special provision can' be made.

Jan 5, 1919

By John Wulff, J. H. Hollomon

SERVICE failures in brass condenser tubes are often due to corrosion. One of the commonest types of corrosion reveals a surface structure of redeposited copper.1 The study of the effect of alloy addition agents in preventing this kind of corrosion has received impetus from the extensive publication of Bengough and May.2 The mechanism of such inhibition gauged from immersion corrosion,' cell corrosion,' and electrolytic potential' measurements is controversial. This controversy may be attributed in part to a lack of definite knowledge5 of the actual nature of the initial films formed in corrosion experiments. In our own corrosion work on copper and 70-30 brass this lack became apparent and necessitated an examination of surface films by X-ray and electron diffraction methods. The present paper is but an introduction to the subject of inhibition and reports the structure of films formed in active corrodents. EXPERIMENTAL PROCEDURE The arsenical coppers and brasses used in this investigation were made by one of the writers* in the plant of the Revere Copper and Brass Co. at Rome, N. Y. Standard commercial melting practice was followed. O.F.H.C. copper and electrolytic zinc were used and all arsenic additions were made by additions of a master copper alloy. The final analyses are given in Table I. Likewise, the extrusion, cold-rolling, and intermediate anneals employed followed standard usage. Final heat-treatments were given to all materials to produce a similar grain size (0.035 to 0.045 mm. for brass and 0.015 to 0.025 for [ ] copper) for the alloys containing various percentages of arsenic. Samples ¼ by ½ by ¼ in. were cut from sheet material resurfaced and finished with 0000 metallographic papers. The surfaces were all degreased in alcohol and benzine before immersion. After immersion in the corrodent, they were washed gently in tap water, dipped first in alcohol and then in pure benzine and allowed to dry in the diffraction apparatus. The reflection electron diffraction apparatus used has been described by Burwell

Jan 1, 1941

R. W. Raymond, New Pork, N. Y.:—I think Mr. Bache has put his finger on the chief source of the danger of dust-, or gas-and-dust, explosions in collieries. 1 mean the persistent determination of the miners' unions to increase their weekly wages by the excessive use of explosives. This would not be feasible if coal-miners were paid by the day; but this form of payment is, for many reasons, not economically practicable; and the universal practice is to pay for the winning of coal according to the quantity produced. If the miner, by using a large amount of powder, can throw down a large amount of coal without corresponding labor on his own part in undercutting and drilling, he will receive more money for less work, provided he is paid for everything—merchantable coal, worth-less dust, slate, and " bone "—resulting from such a method. My attention was called to this matter many years ago by an admirable report of Prof. W. B. Potter, a past- President of the Institute, on the conditions obtaining in this respect in the Illinois coal-field. It was made very clear in that report that considerations of danger to workmen or loyalty to employers could not be relied upon to prevent miners from employing this perilous and wasteful method of increasing their own immediate receipts. So far as I know, only three remedies have been attempted, namely: the enforcement of discipline as to the methods of mining; the refusal to pay for dust, etc., produced by the miners'methods; and restriction upon the use of explosives, effected by requiring the miner to purchase them from the employer, at a price so high as to make it unprofitable for him to use them in excess. All of these attempted remedies have encountered the bitter opposition of the miners' unions. The enforcement of discipline has become almost impossible, if discipline be (as it should be) understood to involve punishment for the violation of rules when no disaster has followed. I

Jan 1, 1910

By I. Cornet

INTRODUCTION WITH the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that the notch sensitivity of magnesium alloy extrusions be further investigated and the influence of various factors upon notch sensitivity be noted. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. The work discussed herein was done under "Restricted" Project NRC-21, reported in Dec. 1943 1; it has been released for publication by the O.S.R.D. SCOPE OF THE INVESTIGATION The notch sensitivity of various magnesium alloy extrusions was determined under axial tension, and also under several conditions of nonaxial tension. Hardness, grain size and other metallographic features were observed; stress-strain data were obtained, and the chemical compositions of the alloys were determined, in order to correlate these quantities with the notch sensitivity. Notch sensitivity under axial tensile load was determined for a few specimens which had been cold worked to various degrees by tensile prestraining. Magnesium alloy extrusions studied included Dowmetal 0, X, J, and M. For comparison, extrusions of aluminum alloy 24S-T, cast bars of aluminum alloy I22-T2, and cast bars of magnesium alloy C were also tested, The specified chemical composition of these alloys is given in Table I. All bars tested were within specification limits of composition. Investigation of the tensile notch sensitivity of various magnesium alloy extrusions, under conditions of axial and eccentric load, showed little or no correlation with stress-strain or other conventional data. Since the many uncontrolled variables present might mask significant relationships, one alloy was selected for intensive study. Magnesium 0 alloy extrusions were subjected to experimental heat treatments, and the changing hardness, tensile strength, microstructure, and notch sensitivity observed. EXPERIMENTAL TECHNIQUES AND PROCEDURES Tensile Testing Bars used for axial loading were machined with 3/8 in.- and with 1/4-in. minimum diam, and included specimens with 6o° V notches (Fig I and 2). Each V-notched specimen was roughed out carefully and then finished with a honed tool. These V-notched bars were sampled frequently, sectioned, polished, and examined at 500 X magnification to control

Jan 1, 1948

By Robert Glass Cleland

DURING the closing month of 1929, Walter Douglas found his health impaired by the strain of many difficult years of alternating prosperity and depression, and in April 1930 resigned the presidency of Phelps Dodge. Douglas was succeeded by Louis S. Cates. The choice broke a tradition that had been held inviolate for almost a hundred years. For the first time in its long history, the direction of the company's policies and operations was entrusted to a stranger without previous Phelps Dodge background, training, experience, or tradition. But the choice was wisely made. For a time at least, the path of Phelps Dodge was to run through rough and dubious ground, and no man in the United States was better qualified to blaze that trail than Louis Cates. After graduating from the Massachusetts Institute of Technology, Cates had served a rough and financially un- profitable apprenticeship at one of the century-old mining camps of Chihuahua, Mexico. Following his return to the United States and a brief interlude as assistant to the president of the National Steel and Wire Company, he had resumed his mining career, first as timekeeper, then as

Jan 1, 1952

By J. E. Burke, C. S. Barrett

THE fine lines shown in Fig 1 are typical of markings that may be detected after polishing and etching deformed specimens of alpha brass and other alloys. Although they have long been the subject of discussion by metallurgists their nature is still uncertain and the names that have been applied to them, such as deformation lines or strain markings, indicate this uncertainty. In this paper which reports the results of a further investigation of their nature, they will be called strain markings. INTRODUCTION Matthewson and Phillips1 in 1916 concluded that strain markings appeared only after deformations that exceeded 20 pct. They objected to the markings being called slip lines believing this term should be reserved for surface markings produced by plastic deformation. In 1921, Vogel2 described similar striations which appeared after polishing and etching the roughly ground surface of numerous alloys. He reported that the markings were crystallographic in nature, and since they resemble Neumann bands in iron, at least superficially, he assumed them to be mechanical twins. In 1928, Matthewson3 reported work by Phillips which indicated that the lines were more readily produced by impact than by slow deformation and that in many cases the twins inside recrystallized grains were parallel to strain markings in the original deformed grains. This was taken as evidence that the markings coalesce into annealing twins, and hence that they themselves are mechanical twins. Many attempts have been made to [ ] demonstrate directly that the markings are mechanical twins. In 1934, Samans4 described the results of X ray studies of two deformed crystals of alpha brass. Evidence was obtained which could be interpreted to indicate that the strain markings are mechanical twins, and this remains the only direct evidence to this effect. Several other attempts to obtain similar evidence by X ray diffraction have failed5,6,7 although in no case was the original method of Samans employed. An

Jan 1, 1948

A Discussion of the papers of James Gayley, on "The Application of Dry-Air Blast to the Manufacture of Iron" (see Trans., XXXV., 746, 1022, also pp. 315 and 745 of the present volume, and of J. E. Johnson, Jr., on "The Physical Action of the Blast-Furnace," p. 454. Chas. B. Dudley, Altoona, Pa.:—I am not a blast-furnace man, and this always puts me at a disadvantage because I cannot go into the details of the making of iron and steel. I have not the experience, and have to take the statements of other people, so what I say regarding the subject of this paper is not in the sense of an expert. When I first heard of Mr. Gayley's experiments, I said to myself, a I fear they will result in failure, since, apparently, Mr. Gayley has forgotten one chemical fact, namely, that carbon does not combine with oxygen in the absence of mater-vapor." This fact which was so astonishing when it was first brought out some years ago, and which those who are interested may find in the Journal of the Chemical Society of London, for 1885, page 349, and 1894, page 611, led me to think that the drying of the air would be a mistake. The general subject of the influence of water-vapor on chemical action is a large one; but the special point in which we are, for the moment, interested, namely, the influence of water-vapor on the combustion of carbon, was especially treated by Mr. H. B. Baker, in the papers referred to. Apparently, however, as the result of Mr. Gayley's experiments, we are to learn that the amount of moisture still left in the desiccated air is sufficient to secure perfectly satisfactory combustion. In thinking over Mr. Gayley's paper, it occurred to me that there were two alternatives, either of which might be chosen, namely, we might dry the air as Mr. Gayley does, or possibly we might, in a very much easier way, simply saturate the air at a constant temperature, and thus get uniform working and

Jan 1, 1906

By V. V. J. Sarma

Interpretation of earth resistivity data involves not only obtaining depth to interfaces but also determining the nature of formations from their resistivity characteristics. Moore's method of interpretation envisages obtaining depths to the interfaces alone. A simple method of estimating the true resistivity values of formations by applying Hummel's formula of average resistivities is proposed. The method would increase the interpretative value of Moore's method as originally proposed. For most of the earth resistivity measurements, the four-electrode configuration developed by Wennerl is employed. In principal, the method consists of energizing (Current I) the ground through two outer electrodes and measuring the resultant potential (v) between the two inner electrodes. The configuration is such that the separation (a) between any two successive electrodes is equal. The apparent resistivity (pa) for such a configuration is given by 2p- a (V/I). By increasing the electrode separation (pa vs a) curves are obtained. Ideally, a homogeneous isotropic formation underground has a characteristic resistivity. However, the field conditions do not present such ideal cases. Almost invariably, even in the same geological bed, the physical conditions are widely different at different parts in the bed. It is further shown that the penetration of the current into the ground for a given horizontal electrode separation, a, is roughly down to a depth, equal to a. It is therefore, evident that the apparent resistivity calculated from the field observations is a weighted average of the resistivities of the materials present down to this depth. With some prior knowledge about the relative dispositions of the geological formations and their physical conditions, it would be possible, by resistivity surveys, to obtain characteristic resistivities for these formations. It is, thus, that the apparent resistivity-electrode separation curves enable one to decipher the resis- tivity distribution at various depth levels and therefore the nature of the geological formations present. Both empirical and theoretical methods have been developed for determining resistivity characteristics of the various formations. The theoretical methods proposed by Tagg2 and Roman3 are derived from studies of the potential distribution on the surface due to the presence of layers of widely differing resistivities underground. The more recent methods of Wetzel and McMurry4 and Wetzel and Mooney5 are but extensions of the original Roman method of superposition. These methods suffer from lack of similarity of the actual field conditions with those of assumed conditions in developing the theory. The empirical methods such as the one developed by Gish and rooneY6 depend purely on personal observation and local peculiarities, and are applicable only for those limited areas. Out of the empirical methods, moore's7 cumulative resistivity method is still found to be applicable in several localities of differing conditions. While Reudy in 1945 adduced some theoretical justification for the method (Eve and Keys),8 Muskat9 and Mooney 10 tried to show the lack of theoretical basis for the same. It is, however, observed that the method in practice "forms a valuable means of successfully attacking the apparent resistivity curves which fail to respond to the Gish-Rooney, the Tagg or the Roman logarithmic methods" (Ramachandra Rao). 11 Comparatively good results are also reported by Melbyel2 by employing Moore's method in interpreting the resistivity results obtained for ground water in the city of Gunnison, Colo. MOORE'S METHOD As has already been pointed out, the application of the theoretical methods is time-consuming, laborious and sometimes not applicable for quick and accurate interpretation of the field data. moore7 has developed a quick method for obtaining depths to interfaces by plotting the cumulative sums of resistivities, against the corresponding electrode separations a instead of plotting the usual Pa — a curve. In this process of continuous integration, corrections for small variations in resistivities, arising due to local surface conditions or adjacent layers, are made, while large consistent variations are brought out

Jan 1, 1963