Search Documents

By Harry Seltz

SEVERAL investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeser1 has made measurements of "average heat capacities" of iron carbide between 1026° and 85° K., using a water calorimeter. His computed true specific heat at 78.1° K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0° K. The cementite used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes" has measured the specific heat of iron carbide, from 102° to 323° K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100° K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3C, S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley' has reviewed these measurements and calculations, and selects those of Roth4 and Naeser5 as worthy of most consideration. Roth has given ?H = 5400 cal. ± 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (ß) he finds OH = 5600 cal. Kelley accepts the rounded figure ?H = 5500 as the heat of formation at 298.1° K., but this value is quite uncertain.

Jan 1, 1939

By J. L. Martin, W. M. Campbell

A new electric logging method, called displacement logging, often gives a direct indication of the presence of mobile hydrocarbons in hydrocarbon-bearing formations. This method is based on the detection of a bank of connate water which is formed between the invading mud filtrate and virgin formation fluids in these cases. The existence of this phenomenon has beer, verified by laboratory studies and by actual field logs taken in known oil sands. INTRODUCTION During the past decade increasing use has been made of conventional electric logs to determine the amount of oil or gas in formations traversed by a borehole. This determination requires knowledge of several factors, such as true resistivity of the formation, formation factor, and water resistivity. Sometimes all of the factors necessary to make a reliable saturation calculation are not available. Also, the computations and corrections which are necessary in such a study often require the services of an experienced log analyst. It has long been the desire of exploration people to have a logging device which will locate hydrocarbon-bearing formations directly without requiring complex interpretation methods. The displacement log, while not completely fulfilling this desire, appears to be a Step in that direction. Basis for the Device The basis for this device stems from a phenomenon which occurs when mud filtrate invades a formation which contains displaceable hydrocarbons. As the mud filtrate invades the formation, most of the oil or gas is pushed out of the invaded zone, leaving residual oil. However, in addition to displacing most of the oil or gas, the connate water is also swept out, since the originally irreducible water is mobile in the presence of a water phase.1,2,3 Tonsequently, this irreducible water piles up as a bank between the virgin oil zone and the invading filtrate. If the mud filtrate is of higher resistivity than the formation water— as is commonly the case—the resulting annular zone, containing the bank of formation water, will be of lower resistivity than either the virgin oil-bearing formation resistivity or the invaded zone resistivity. This resistivity configuration, going from high to low to high again as the distance from the borehole increases, is found only in those zones which contain displaceable hydrocarbons. A device which would reliably detect this low resistivity zone would give a direct indication of mobile hydrocarbons. Illustrations This phenomenon is illustrated in Fig. 1 and 2. Fig. 1 shows a sketch of a zone containing salty connate water plus displaceable hydrocarbons, along with graphs showing fluid content and electrical resistivity vs distance from the borehole, before invasion occurs. Fig. 2 shows this zone, together with fluid content and resistivity graphs. after invasion by a fresh water mud. The resistivity pattern on moving away from the borehole is high: low: high. The absence of the low zone phenomenon in water zones is illustrated in Fig. 3 and 4. Fig. 3 shows a sketch of a zone containing salty formation water and residual oil, along with graphs showing fluid content and electrical resistivity vs distance from the borehole, before invasion occurs. Fig. 4 shows this water zone, together with fluid content and resistivity graphs, after invasion bv a fresh water mud. In this case the resistivity pattern on moving away from the borehole is high: low since there is no change in water saturation at the head ol

Jan 1, 1956

By H. W. Mead, C. E. Birchenall

SELF-DIFFUSION of iron in austenite is a process which may play a significant role in some of the practically important reactions which occur in solid irons and steels. It also provides a system in which the interaction of vacancies on substitutional sites and atoms in interstitial positions may be investigated. For both purposes, accurate values of the diffusivities are required. Two sets of previous measurements exist, each containing features which require checking. In the course of an investigation to determine the rate of diffusion of iron in certain steels, Garwick and Rosenqvist' measured the self-diffusion coefficient of iron in a 0.10 pct* C steel and obtained a dicated that while at lower temperatures D increased with increasing carbon content, at the higher temperatures it first increased and then decreased. At the same time the activation energy decreased linearly from a value of 69,000 cal per g-atom for pure iron to 33,000 cal per g-atom at 1.06 pct C. This rapid decrease in activation energy implies that iron at higher temperatures within the austenite range would diffuse more slowly in high carbon steels than in steels of lower carbon content. Experimental Procedure The radioactive iron used in this work was obtained from Oak Ridge National Laboratory. The unit consisted of about 1 microcurie each of Fe7 and Fe It was allowed to decay for two years. At the end of this time most of the Fe with a half-life of 46.3 days, had decayed, while most of the original Fe(half-life 2.91 years) still remained. The iron as chloride was extracted into an ether layer, using the method of Ashley and M~rray. After evaporation of the ether the iron chloride was dissolved in 250 ml of aqueous solution containing 2.4 gpl Fe. The compositions of the steels used are listed in Table I. Disks of ¾ in. diam and about ¼ in. thick were machined from these steels for use in diffusion couples. The disks were surface ground on both sides to ensure parallel opposite faces. One face of each disk was polished through 000 emery paper. Half of the prepared disks were plated with radioactive iron. For this, 1 ml of the radioactive iron

Jan 1, 1957

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,000. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service.

Jan 1, 1946

By Frank Firmstone

When in charge of the Glen don Iron Works, the importance of good methods of filling was forcibly brought to my attention, and it occurred to me that the first step toward the discovery of the best plans was the accumulation of exact information as to the distribution actually effected by various chargers; also, that something could be done in this direction by careful measurements in the furnace, to be afterwards recorded for comparison on drawings. The figures shown herewith have been prepared from such measurements, and nearly all of them refer to Glendon, where the fuel used was anthracite and the ore-mixture about threequarters of New Jersey magnetic ores and one-quarter of brown-ores from the vicinity of the works. Every occasion furnished by the blowing-in of furnaces was utilized, but the data accumulated rather slowly in this way; and, opportunity oEering to make special trials at no great expense, the figures from 2 to 7 were thus obtained. The trials were made by dumping a hopperful (6 barrows) of material at once into the furnace, and, when all the fuel of a round (12 barrows) had been put in, the profile of the upper surface was obtained by stretching a steel tape across the top on a diameter and at a known height. By measuring down from this with a graduated rod, the profile was easily obtained with sufficient accuracy, especial pains being taken to get correctly the crests of the ridges and the bottoms of the hollows, as many intermediate points being included as seemed necessary. This was repeated on another diameter when there was occasion. The same course was followed for the limestone and ore.

Jan 1, 1899

By James C. Bayles

The ideal pressure-tube is obviously the one which combines the greatest strength with the least weight of material consistent with the uses for which it is designed or employed. The inside of the pipe is the first concern of the engineer. It should be cylindrical, smooth, and of the requisite capacity for the purpose in view. It should be in lengths as great as can be oonveniently handled, so that the couplings may be as few as possible. With the walls of the tube the engineer has no further occasion to concern himself than to make sure they are adequate to carry the internal and external pressures to which they will be subjected. It is as true of a pipe as of a truss, that when it is strong enough to give the requisite factor of safety, nothing is gained by having it stronger. Anything more than this means dead weight, which has to be paid for many times, first as material, and again and again in the costs of transportation and handling, until it reaches its place in the trench or on supports. In use it must be and remain tight against all leakage, and must sustain whatever is placed over or upon it, or suspended from it, without deformation or injury. Finally, in addition to meeting all the immediate requirements of service, it must possess qualities of durability which warrant a reasonable expectation of a long life of usefulness. The wise engineer no longer regards it as reasonable to depend upon mere bulk of its own material for the protection of a metal as readily impaired or destroyed by oxidation as iron or steel. The metal must have a coating which will be and remain impervious and indestructible. When all these conditions are met, we have as near an approach to the ideal tube as can be attained with the materials now available for their manufacture. Steel wed constructively, to the best advantage, meets these requirements most perfectly. Gold alone would do it better. If we search through the whole list of metals and alloys we find nothing available which so perfectly meets the requirements as a pipe material as steel. Mr. Hamilton Smith, Jr., in a paper on the expedients adopted on

Jan 1, 1891

MRS. SIDNEY J. JENNINGS, President MRS. ARTHUR S. DWIGHT, First Vice-President MRS. KARL EILERS, Second Vice-President MRS. H. W. HARDINGE, Third Vice-President MRS. BRADLEY STOUGHTON, Recording Secretary MRS. AXEL 0. IHLSENG, Corresponding Secretary MRS. HARRIS K. MASTERS, Treasurer Welfare Committee MRS. C. C, BURGER, Chairman Sub-Committees Americanization Belgian Relief MRS. LEVI HOLBROOK, Chairman MRS. HENRY H. KNOX, Chairman Emergency MRS. HERMAN A. PROSSER, Chairman A very successful meeting Of the Council of the Woman's Auxiliary was held Wednesday, July 18, and plans for war relief work were thoroughly discussed. The Belgian Relief Committee has sent out the following letter to the ten local sub-committees, which were formed to raise money to feed the Belgian children: "The Commission for Relief in Belgium announced in a letter from Mr. Hoover that after the first of June the United States Government would take over the relief of Belgium and Northern France and called attention to the following paragraph: ?Naturally, having built up such an effective organization you will desire to keep it alive as far as possible, and we venture to suggest that, although the general relief of the countries involved will now be met by the Government appropriations, emer-gencies and special conditions may arise which could only be met by private donations. In such circumstances your organization will afford a ready means of meeting the demands of the situation, whatever they may be. Should any of your contributors

Jan 9, 1917

By Ralph Monaghan, Arthur Youmans

General principles of scintillation counter-type instruments for radioactivity logging are discussed and the various possible causes for instability are examined. It is shown how instrumentation problems are solved. Means are discussed for minimizing drift and instability due to "fatigue" of the photomultiplier tube and neutron activation of the crystals. INTRODUCTION Neutron and gamma-ray logs made with logging instruments employing scintillation counters are now routinely available from most of the logging service companies. The superior characteristics of scintillation counters by comparison with older types of detectors promises to bring about important improvements in quantitative interpretation of radioactivity logs. Moreover, new types of logs can be made with scintillation counters which are not possible with other detectors. But in spite of the obvious superiority of these counters with respect to efficiency, speed, and versatility, they suffer from a number of inherent difficulties and weak- nesses. Unless these inherent diffi-culties are fully recognized and satisfactorily overcome by sound engineering of the associated instrumentation, scintillation counter logs are particularly likely to exhibit drift and instability of sensitivity. This defect in logs when they are intended for quantitative interpretation is intolerable and more than outweighs any advantages over the older type of instrumentation when the latter is operating correctly. SCINTILLATION COUNTER OPERATION In general all radioactivity logging instruments consist of a detector sensitive to gamma radiation or to neutron radiation coming from the strata. This radioactivity is either due to naturally decaying radioactive elements in the rock, radioactivity induced in the rock by a neutron source in the instrument, or scattering by the rock of neutrons or gamma rays coming from a source in the instrument. In the scintillation counter the gamma radiation or neutron radiation reacts with the scintillation phosphor to produce light pulses. These light pulses are then converted to amplified electrical pulses by the multiplier phototube. Basically the problem of making a good scintillation counter logging instrument is to make the radiation sensitivity of the system as nearly constant as possible. The size of each scintillation counter pulse is dependent on the energy of the individual quantum of radiation being detected. In normal radiation logging, gamma rays of all energies, up to some maximum value, reach the detector. If a suitable scintillator is used, such as a sodium iodide crystal, each gamma ray produces a number of photons proportional to the energy absorbed by the crystal from the impinging radiation. The light flashes are detected by means of a photo-multiplier tube which contains not only a photo-sensitive cathode from which photoelectrons are collected, but also an amplifier, called an electron multiplier, built inside the photomultiplier tube; the electron multiplier usually has about 10 stages, having an over-all gain of perhaps 500,000. In an ordinary gamma-ray log one wishes to detect all gamma rays down to the lowest possible energy; therefore, one wishes only to reject the "noise" pulses which are invariably present due to thermal emission of electrons from the photo-cathode of the photomultiplier. In other radioactivity logs it may be desired to measure the radiation within a particular energy band, or above

Jan 1, 1958

By F. C. Langenberg, J. Chipman

New data on the distribution of silicon between slag and carbon-saturated iron at 1600oand 1700oC are presented which, in combination with previously published data, permit the determination of silica activities over a broad range of compositions in the CaO-Al2O3-SiO2 system. The distribution of silicon between graphite-saturated Fe-Si-C alloys and blast furnace-type slags in equilibrium with CO has been described in previous publications.1"3 In this past work the silica-silicon relation was established at temperatures of 1425" to 1700°C for slags containing up to 20 pct Al2O3. This paper presents the results of additional studies at 1600" and 1700° C which extend the silicon distribution data at these temperatures for CaO-A1203-SiO2 slags over a range from zero pct A12O3 to saturation with A12O3, or CaO.2A12O3. The upper limit of SiO, is set by the occurrence of Sic as a stable phase when the metal contains 23.0 or 23.7 pct Si at 1600" or 1700°C, respectively. The activity of silica over the expanded range is determined directly from the distribution data.3 Recently, 4-7 other investigators have studied the activities of SiO, and CaO, principally in the binary system, using different methods and obtaining somewhat different results. EXPERIMENTAL STUDY The experimental apparatus and procedure have been fully described in previous publications.1, 3 Six new series of experimental heats have been made, four at 1600° and two at 1700°C. Master slags of several fixed CaO/A12O3 ratios were pre-melted in graphite crucibles, and these were used with additions of silica to prepare the initial slag for each experiment. Slag and metal were stirred at 100 rpm and CO was passed through the furnace at 150 cc per min. The initial sample was taken 1 hr after addition of slag at 1600°C or 1/2 hr after addition at 1700°C. The run was normally continued for 8 hr at 1600°C or 7 hr at 1700°C, and the final sample was taken at the end of this period. Changes in Si and SiO2 content indicate the direction of approach to equilibrium, and in a series of runs where the approach is from both sides this permits approximate location of the equilibrium line. Fig. 1 shows the results of such a series of 15 runs at 1600°C for slags of CaO/Al2O3 = 1.50 by weight. Figs. 2 and 3 record other series at 1600°C and Fig. 5 a series at 1700°C with fixed CaO/Al2O3 ratios. The results of the experiments at 162003°C have been reported in part in a preliminary note.3 In the experiments recorded in Figs. 4 and 6, the slags were saturated with A12O3 (or with CaO.2A12O3 within its field of stability) by suspending a pure alumina tube in the melt during the course of the run. The final slag analyses were used to establish the liquidus boundaries8 in the stability fields of CaO.2Al,O3 and of A120,. ACTIVITY OF SILICA The free-energy change in the reaction has been calculated by Fulton and chipman2 from recent and trustworthy data including heats of formation, entropies, and heat capacities. The more recent determination by Olette of the high-temperature enthalpy of liquid silicon is in satisfactory agreement with the values used and therefore requires no revision of the result which is expressed in the equation: SiO, (crist) + 2C (graph) = Si + 2CO(g.) [1] &F° = + 161,500 - 87.4T The standard state for silica is taken as pure cristobalite and that of Si as the pure liquid metal. Since the melts were made under 1 atm of CO and were graphite-saturated, the equilibrium constant for Eq. [I] reduces to K1 = asi /asio2 The value of this constant is 1.77 at 1600°C and 16.2 at 1700°C. Through K1, the activity of silica in the slag is directly related to the activity of silicon in the equilibrium metal.

Jan 1, 1960

By A. H. Larson, R. J. McClincy

The activity of Sb,03 in PbO-Sb,03 slags containing less than 50 mol pct Sb,03 was determined by the inert-gas saturation method at 700°C. In this composition range, the activity gf SbzO3 shows a strong negative deviation from ideality. The activity of PbO in these slags was calculated by application of the Gibbs-Duhem iniegration to the Sb203 activity data. The calculated activity of PbO in slags containing more than 63 mol pct PbO was found to deviate in a positive direction from ideality uthile a negative deviation was found for slags containing less PbO. The standard Gibbs free energies of formation of Sb,03 and PbO. Sb203 have been calculated and compared with existing data in the literature. The activity of Sb203 in PbO-Si0,-Sb203 (PbO/SiO, = 2) slags containing less than 25 mol pct Sb,03 was also determined by the inert-gas saturation method at 700°C. In this composition range, the activity of Sbz03 shows a very large negative deviation from ideality. VERY little experimental work has been published in the past to determine equilibrium data in the oxide systems connected with the refining of lead. These data are of value since impurities such as antimony, arsenic, and tin must be removed from lead and recovered for further treatment. Equilibrium studies on antimony and arsenic systems are also of interest for the design of new processes for lead refining and lead dross treatment. Maier and ~incke' first determined the liquidus curves for the PbO-Sb203 system and identified the compound PbO . Sb203. They found the phase diagram for this system to be two simple eutectics located on either side of the congruent melting compound. They also determined a very limited amount of vapor pressure data for Sb406 abbve PbO-Sba3 melts at 697"~. A second phase diagram investigation on this system was reported by Hennig and Kohlmeyer' who confirmed the existence of the compound PbO . Sb203 as well as the form of the diagram. A disagreement was noticed, however, in that their liquidus temperatures over nearly the entire composition range were higher than those reported by Maier and Hincke. Barthel~ and pelze14 redetermined the liquidus curve at the PbO-rich end of the PbO-Sb@, system and agreed very closely with the results of Maier and Hincke. None of the investigators mentioned above reported any mutual solid solubility in the PbO-SbD3 system. Zunkel and Larson5 have determined the phase diagram for the PbO-rich end of the PbO-Sb203 system by slag-metal equilibrium studies in the Pb-PbO-Sb203 system and by thermal analysis studies in the PbO-Sbz03 system. A maximum solid solubility of 5.6 mol pct Sb203 in PbO was observed at the eutectic temperature of 604°C. Their results for the phase diagram agree favorably with those of Maier and Hincke. The vapor pressure of Sb2O3 in the temperature range from 470" to 800°C has been determined by Hincke, using a modification of the transportation meth~d.~ His results for temperatures below the melting point of Sba3 are the only data reported in the published literature. The predominant vapor species has been shown to be Sb,06 by Norman and staley.? Myzenkov and Klushin,8 using the boiling-point method, have determined the pressure of Sb406 above liquid SbD3 in the temperature range from 715" to 1025°C. The agreement between these two studies is not very close. A portion of the discrepancy lies in the fact that Hincke used silica crucibles, which were attacked by the liquid Sbz03 at high temperatures. This fact does not account, however. for the large difference observed at the melting point. ~aier' gives a brief summary of vapor pressure data for Sb,O, above pure liquid Sbz03 which agree quite well with the data of Myzenkov and Klushin at temperatures near the melting point. This paper describes the determination of Sb2O3 activity data in the PbO-Sb203 and Pb0-Si02-Sb203 (PbO/SiOz = 2) systems by the inert-gas saturation method. These activity data are compared with the data calculated by Zunkel and arson. EXPERIMENTAL Materials. The materials used in this investigation were analytical reagent-grade PbO (99.8 pct PbO, 0.14 pct insoluble in CHsCOOH, 0.02 pct not precipitated by HB, 0.1 pct CaO, and 0.08 pct SiOz), Sbf13 (99.6 pct Sb203, 0.004 PC~ C1-, 0.005 PC~ SO;-, 0.15 p~t AS, 0.001 pct Fe, and 0.03 pct other heavy metals such as Pb), and SiOz (chromatographic grade). Apparatus for Vapor Pressure Determinations. The apparatus used in this investigation consisted of a transportation reaction system with two separate gas trains. The argon transporting gas was first mixed with a small amount of hydrogen, metered, and dried by passage through silica gel and anhydrone drying tubes arranged in series. After this preliminary drying, the argon was passed through copper wool at 500°C to convert the residual oxygen to water vapor which was removed by three anhydrone drying tubes. A second stream of argon was metered and dried and then passed around the outside of the alumina reaction tube to flush away the volatile species to pre-

Jan 1, 1970

By AIME AIME

SILVER reached a new high, with the ceiling the limit, at the annual Institute dinner at the Commodore on Washington's Birthday night. Carrying along as ballast other commodities, such as rolls, roses and ferns, souvenir boxes and table number placards, hundreds of silvery balloons, cut loose from their moorings at the tables, bounced idly against the plaster decorations high overhead. At the head table, Scott Turner, retiring President, pre- sided as toastmaster, with the new President, Frederick M. Becket, on his right, and the Chairman of the New York Section, Sydney H. Ball, on his left. Many other distinguished Institute members, medalists, and representatives of organizations and committees, ranged to the east and west. Each had the opportunity at least to rise and bow.

Jan 1, 1933

By James E. Chapman

The observations here presented are not those of an expert accountant, but of one who, while he has seen considerable service in the accounting departments of large companies, has spent more time in engineering and operating. This paper is intended to cover, in a measure, mine accounting for small mines, as distinguished from the elaborate systems, requiring many persons in the accounting department. I shall attempt to outline a system embracing the essentials of accounting, and simple enough in form to permit one or two persons to carry it on from month to month, in sufficient detail to be able to tell quickly the grade of ore, the prices received for metals, costs per ton for mining and milling, costs per foot for development, upward or downward tendencies in costs, ore settled or in transit, cash on hand, stocks of supplies on hand, efficiency of labor, etc. As in all accounting, there are two main divisions: that of revenue received for what is sold, and that of disbursements made for what is bought, so in mine accounting we have to consider chiefly the income derived from sales of ore or concentrates, and the expenses incurred in producing the said ore or concentrates in a marketable condition. I. Income The revenue of a mining company from the sale of ore or concentrates comes in the form of remittances, accompanied by settlement sheets made out by the buyer of the mine product, such as a smelting company. It is the duty of the mine accountant (or the person to whom this is assigned in connection with other work) to check these settlement sheets, against both the mine weights and assays, and the schedules of prices arranged between the mine and the smelter. As a rule, quotations for silver, lead, zinc, copper and other metals enter into the settlements, and require checking, as do also bills of lading. Each step of the arithmetical calculation is also checked.

Jan 1, 1917

By SAMUEL GOMPERS

THE name engineer makes a very strong appeal to one who appreciates the mechanism underlying the fabric of our civilization. Engineers are scouts of civilization. We send them ahead into the lone 'places-the wilderness, the jungles, the great watery expanses, to build the highways necessary for civilized man. The engineers must deal with Nature, with that mysterious dynamic thing we call "force," with materials. It is their function to direct the human activity necessary to coordinate these forces and material in order to make them serve the needs and aspirations of men. Because of my high conception of the engineering profession I was glad to accept the invitation to address The American Society of Mechanical Engineers to voice my understanding of the possibilities of your work as engineers of industry, and to suggest what seems to me the responsibility of the-engineer to the whole modern industrial system.

Jan 1, 1921

By John Garcia

COAL MINING, as well as all the other major in-dustries of Russia, is controlled by the Soviet Gov-ernment by means of organizations in each dis-trict, known as "Trusts," such as the "Kisel Coal Trust" in the Urals, the "Donugol Trust" in the Ukraine, etc., and each Trust functions as a unit, reporting direct to the chief of the department of the government at Moscow. The responsible head of each Trust is usually a mem-ber of the Communist party and, filtered through his organization, one generally finds a fair proportion of Communists in "key" or important positions, such as purchasing agents and local managers or superinten-dents, but in the majority of places requiring technical or professional knowledge, or trained brains and ex-perience, little or no attention is paid to a man's political opinion provided, of course, he "behaves himself." These different Trusts were authorized or ordered by the Central Committee at Moscow to investigate the methods of mining and type of mines developed in all other coal producing, countries of the world, and after a period of several years of intensive investigation and study reported back to headquarters that the modern American mines were the most efficient, recommending that the program for the rehabilitation of the Russian coal mining industry should follow the lines of American practice. The Trusts were then authorized to negotiate with American engineering firms for technical service for mine designs, and invited Americans to send commis-sions to Russia to prepare and submit to the Technical Council one or more projects for a complete modern American-type operation adapted to the local conditions. A "project" is a preliminary set of designs on the entire mine, top and bottom, with specifications. cost estimates, production costs, schedule of operation, budget of expen-diture, etc., and is quite an elaborate and sizable under-taking-I might say, it took six of us working tooth and nail for over three months to finish our first project.

Jan 3, 1928

By AIME AIME

ED DIX, after studying both mechanical and electrical engineering at Cornell, started out to be an electrical engineer, then taught material testing at Cornell, and decided to become a metallurgist. He was successively employed by the Morse Chain Co. as metallographist, by the Baltimore Copper Smelting and Rolling Co., as chief of the testing department of the Bureau of Aircraft Production, as assistant engineer of tests of the Aluminum Castings Co., and as chief of the metals branch, engineering division, U. S. Air Service. Since 1923 he has been with the Aluminum Co. of America, now as chief metallurgist.

Jan 1, 1936

By COREY C. BRAYTON

OUR first air travel began at Barranquilla on a trip to the platinum dredging-operations at Andagoya. The fare is based on a minimum weight of passenger, and I will have to admit that the minimum is too low. To make this trip by boat would have necessitated going back to the Canal, thence down to Buena Ventura, and up the San Juan river, which would have taken, counting delays, two or three weeks. The time by Scadta airplane was six hours. We stopped at Cartagena for a day to look over that historic city. The route from there lay along the north coast to the mouth of the Atrato river, then up this river, over the jungle, and over a divide some 300'ft. in elevation and down the San Juan river a few miles to Andagoya at the junction of the Condoto. The General

Jan 1, 1930

By H. I. Ashby

INITIAL development of the south orebody at San Manuel is being carried out from the No. 1 and No. 2 shafts. The haulage and grizzly levels are being driven to develop the upper one third of the massive hydrothermally altered and fractured monzonite orebody. This first haulage level has been placed at the 1475-ft level with a grizzly level 60 ft above. The grizzly level will be connected to all service shafts so that men and supplies can come down to the grizzly level and go to working places without congesting the haulage level. These connections are also a vital part of the ventilation plan. The haulage level is being advanced along the north and south fringes of the orebody and connections are being driven to the three shafts now under construction. The No. 1 and No. 2 shafts will serve the development work with supplies, skip hoisting, and ventilation at each shaft and the two shafts are connected on both the grizzly and haulage level.

Jan 7, 1954

By [Dipl. -Ing. ] Karl Angerer

The "New Austrian Tunneling Method" is one of the most significant developments in European tunneling in the last 15 years. I hope this report will show the significance of this tunneling method, which was developed in Austria exactly 18 years ago and which is now used in many European countries. In Austria from 1948 to 1953, the Moll tunnel with a length of 11.6 km (about 7.3 miles) was constructed as a part of the Kaprun power plant. Depth of overburden varied from 1000 to 1400 m, and there were many rock bursts in calcareous-schist formations. Here for the first time it was found that a thin concrete lining would help to prevent rock bursts if it was sprayed on the rock soon after blasting. During construction of the Prutz-Imst tunnel in Austria from 1953 to 1956, the shotcrete lining was sprayed on the phyllite surface a certain distance behind the blasting face to prevent rapid rock decomposition. This method was also tried in soft-rock sections of the tunnel where steel and wood supports usually were necessary. To prevent loosening of the rock, application of the sprayed concrete was tried immediately after blasting. This method made it possible to tunnel through very soft ground. Where necessary, the shotcrete was supplemented by steel arches and mesh reinforcement. At that time (1953-1956), the machines and equipment for guniting or spraying concrete were being improved rapidly and it became possible to spray aggregates up to 25 mm in diam. Hardening accelerators brought quicker strength and better adhesion of the shotcrete-this also made it possible to use the method in wet tunnels. If the tunnels are extremely wet or flowing with water, it is necessary to seal off the wet rock or drain the water, using, for instance, the Oberhasli method. After these first successful steps with the new Austrian method, large portions of the Schwarzach power plant in Austria were designed and built. At this operation, shotcrete was used almost exclusively for tunneling work. It was on this site where, for the first time, a tunnel 120 m long with a 45-sq- m section was driven through overburden without one piece of timber

Jan 1, 1970

By W. A. Mudge

ONE of the most prominent features of our present-day industrial development is the ever-increasing demand put upon materials of con-struction. Engineering ingenuity, within the past 25 years, has been unusually active, and in some fields at least engineers frankly say that engineering design has progressed as far as the limitations imposed by the properties of the present materials of construction will permit. Consequently, they are today demanding improvement in their working materials and seeking new ones, through the aid; of which the present limitations of design may be overcome. The activity of this search is evident in all fields, but it is particularly so in that of structural materials required to be resistant to corrosion. The corrosion resistance of metals and alloys is never absolute and all-inclusive; a particular alloy will withstand some corrosive conditions well and fail utterly tinder others. Furthermore; other properties, physical and mechanical, required in-conjunction with corrosion resistance vary considerably for different commercial applications. One wants a soft, ductile sheet metal resistant to atmospheric corrosion; another, a high-strength- alloy resistant to sulfuric acid. The last decade has witnessed active and definite progress in the development of high-strength, corrosion-resisting alloys. In June, 1924, a symposium by the American Society for Testing Materials, on Corro-sion-Resistant, Heat-resistant and Electrical-resistance Alloys, disclosed no less than 60 commercial alloys the properties of which were described as being suitable for industrial service where corrosion resistance

Jan 1, 1935