Search Documents

By Oscar Weiss

An aerial magnetometer survey was carried out by the author's geophysical organization over the Vredefort dome, where Witwatersrand beds are wrapped around a granite plug 25 to 30 miles in diameter. The well- known magnetic shales of the Lower Witwatersrand system (to be referred to as LWW) give strong negative anomalies over the out-cropping portion of the dome. This is unusual as these same shales -cause positive anomalies over large areas near Johannesburg and along a strike of 130 miles between the East Rand and Klerksdorp. It is suggested that the negative polarization is caused by heat and stresses connected with the doming. This negative polarization of sedimentary beds, which usually cause positive anomalies, is a good example of how "magnetic lows" can be caused by "structural highs." Significant magnetic anomalies should be tested by gravity and seismic methods irrespective of the sign of the anomalies.

Jan 1, 1949

By A. M. Gaudin

THE study that is presented here was undertaken in order to condense information concerning comminution, and covering a great variety of conditions, into one or several rules which would be of use in the development of a systematic theory as well as in many directly practical ways. As the result of this work, the following conclusions appear justified 1. Rocks may be classified, from the point of view of comminution, into two general classes which are (a) structurally homogeneous, and (b) structurally heterogenous. Structurally homogeneous rocks are those in which fracture takes place through grains and grain boundaries alike; heterogeneous rocks are those in which fracture passes in preference through grain boundaries. 2. If a sized product composed of structurally homogeneous rock grains is crushed, a product results in which the relation between the percentage weight of grains of various sizes and these sizes themselves follows a definite law. This is not true of structurally heterogeneous rocks. 3. Ball milling with structurally homogeneous rocks, and under certain conditions, presents exceptions to this rule. 4. In ball milling with structurally homogeneous rocks, there exists a critical ratio of size of feed to size of balls, above which the machine operates essentially by surface wear, and below which it operates essentially by breaking across the body of the particle. 5. In ball milling, with structurally homogeneous rocks, and when the size of feed grains exceeds the critical size, the particles worn off are of a, substantially definite size which depends upon the ball size 6. In the case of a typical heterogeneous rock, such as Manhattan schist, particles are crushed in such a way that there is a greater proportion of grains of the size that is the average grain-size of the rock than there would be in that range of size with a structurally homogeneous rock. This has been found to be true with-all the crushers tested. 7. Different methods of crushing produce grains of different shapes.

Jan 2, 1926

By L. H Levenson, Charles S. Barrett

The orientation of metal crystals and grains, both large and small, can be detcrmined conveniently and accurately without the use of X-ray apparatus. This seems to be appreciated by so few metallurgists that it may be useful to explain in detail the method we have found most satisfactory in the laboratory—the reflection of light from crystallographie etch pits. This note includes a description of a suitable inexpensive instrument and instructions for etching various metals and for plotting the data. As the stereographie projection is used to facilitate handling the data, this note may he considered as an appendix to an earlier review of the metallurgical uses of the stercographie projection.' Various methods involving etch pits have been used by other investigators. Bridgman's method2 consists of attaching the specimen to a sphere (a transparent sphere is convenient4 , holding it at arm's length, and marking a spot on it when it has been turned so that the eteh pits reflect light into the eye of the observer from a lamp standing behind him. It has an accuracy of about 2" and is extrernely rapid. A greater accuracy can be obtained by having the reflected light fall on a screen, as has been done by Czochralski,5 Chalmers,6 and Schubnikov.7 All of these methods have been intended for undeformed single crystals. Tammann and his coworkers3,8 developed a method for estimating the number of grains in a polyerystalline aggregate having orientations in a given region of the stereographic triangle and thus obtained statistical information about deformation and reerystallization textures. While the method has had some use in recent years,9 it is not applicable to the majority of problems in physical metallurgy. Smith and Mehl10 determined orientations by plotting the directions of the sides of individual etch pits on a stereographic projection. The accuracy is limited to about 3" and the method requires careful polishing and high magnification.

Jan 1, 1940

By Charles S. Barrett, L. H. Levenson

The orientation of metal crystals and grains, both large and small, can be detcrmined conveniently and accurately without the use of X-ray apparatus. This seems to be appreciated by so few metallurgists that it may be useful to explain in detail the method we have found most satisfactory in the laboratory—the reflection of light from crystallographie etch pits. This note includes a description of a suitable inexpensive instrument and instructions for etching various metals and for plotting the data. As the stereographie projection is used to facilitate handling the data, this note may he considered as an appendix to an earlier review of the metallurgical uses of the stercographie projection.' Various methods involving etch pits have been used by other investigators. Bridgman's method2 consists of attaching the specimen to a sphere (a transparent sphere is convenient4 , holding it at arm's length, and marking a spot on it when it has been turned so that the eteh pits reflect light into the eye of the observer from a lamp standing behind him. It has an accuracy of about 2" and is extrernely rapid. A greater accuracy can be obtained by having the reflected light fall on a screen, as has been done by Czochralski,5 Chalmers,6 and Schubnikov.7 All of these methods have been intended for undeformed single crystals. Tammann and his coworkers3,8 developed a method for estimating the number of grains in a polyerystalline aggregate having orientations in a given region of the stereographic triangle and thus obtained statistical information about deformation and reerystallization textures. While the method has had some use in recent years,9 it is not applicable to the majority of problems in physical metallurgy. Smith and Mehl10 determined orientations by plotting the directions of the sides of individual etch pits on a stereographic projection. The accuracy is limited to about 3" and the method requires careful polishing and high magnification.

Jan 1, 1940

By E. A. Gulbransen, A. Pebler

Pressure-composition isotherms have been determinedfor the systems ZrMo2 -H2 between 0" and 900°C at hydrogen pressures between 10-4 and 760 Torr. Tkese studies plus X-ray diffraction analyses of selected compositions show that these intermetallic compounds form a complete series of hydrogen solid solutions within this temperature and pressure range. The partial molar enthalpies and entropies of solution of hydrogen in the three intermetallic compounds were calculated. The solubility of hydrogen in these Laves phases can be related to their free electron concentration. ThE reaction of hydrogen with inter metallic compounds of zirconium with Laves phase-type structure has both theoretical and practical interest. The in-termetallic compounds have structures different from any of the pure metals. In addition the electron to atom ratio of the intermetallics varies appreciably. In the nuclear materials field, these materials are of interest since intermetallic compounds may exist as precipitates in commercial zirconium alloys with transition metals. From studies on the hydrogen reaction, one can establish the stability of the intermetallic compounds relative to the hydrides of the component metals. The intermetallic compounds may also be used as getters for hydrogen and as materials for hydrogen storage. This paper will present the results of equilibrium and structural investigations of the ZrCr2-H2, the ZrV2-H2, and the ZrMo2-H2 systems for the temperature range of 0" to 900°C and the pressure range of Torr to 1 atm. A complete thermochemical analysis will be made of the measurements. Some of the results have been referred to in a survey paper' covering the types of hydrogen behavior observed in zirconium alloys. LITERATURE ZrCr2 is the only intermetallic phase in the Zr-Cr system.' It exists in two allotropic modifications. Between 900" and 1000°C the hexagonal MgZa (C14) structure transforms into the cubic MgCu2 (C15) structure. Beck4 has previously shown that the intermetallic ZrCrz takes up hydrogen into solid solution up to a composition H/ZrCr2 = 1.14 at room temperature and 1 atm hydrogen. A ZrCr2 hydride was stated to have a fcc structure. The binary Zr-V system has been investigated by williams5 although Rostoker and Yamamoto 6 had given earlier a partial phase diagram. ZrV2 was the only intermediate phase found in the system. wallbaum7 reported earlier that the compound ZrV2 hp the MgZm (CJ4) type structure with a = 5.288A and c = 8.664A. This was not comfirmed by Elliot8 nor by Matthias, Compton, and corenzwit9 who reported that ZrV2 has a cubic MgCua LC15) type structure. The latter authors gave a = 7.429A. Also, several authors do not agree on the temperature of the peri-tectic horizontal. It appears that ZrV2 may exist in several modifications. A high capacity for occluding hydrogen was reported by Beck4 who found H/ZrV2 = 1.38 at room temperature and 1 atm of hydrogen. ZrMoz is the only intermetallic phase in the Zr-Mo system.10 ZrMoa is formed by a peritectic reaction of the melt with a molybdenum-rich solid solution. ZrMo2 has the C15-type structure with a = 7.59A. MATERIALS High-purity chromium, vanadium, and molybdenum were used together with grade 1 crystal bar zirconium to prepare the alloys. Table I lists the chemical analysis and the sources for the metals. Ten-gram alloy compacts were levitated and melted in an inert argon

Jan 1, 1968

By Richard A. Queeney, Lance G. Peterson

ESTIMATES of the stacking fault free energy of copper reported in the literature show an extensive divergence of results. Based on measurements of dislocation node radii, Thornton et al.7 find the lower limit of stacking fault energy to be 60 ergs per sq cm: Jossang and coworkers4 estimate the same value should be less than 40 ergs per sq cm. Assuming stacking fault free energy to be twice the coherent twin boundary free energy, Valenzuela8 reports 72 ergs per cm, while Inman and Khan2 cite a value of 24 ergs per sq cm. which can no doubt be accounted for by almost complete absence of interstitials in solution. However, the minute concentration was sufficient to permit observable recovery of dislocation damping. Assuming a dislocation density of 1010 CM -2 and an average loop length of 0.5 , a concentration of interstitials as low as 0.01 at. ppm is sufficient to reduce dislocation damping by more than a factor of ten. The concentration of interstitial solute atoms in Ferrovac E-0.15 pct Ti was thus estimated at 0.01 at. ppm < (C + N) < 2 at. ppm. The absence at elevated temperature of strengthening due to interstitials, Fig. 1, was therefore anticipated in the titanium alloy. The temperature dependence of the flow stress below 300°K was unaffected by addition of either titanium&apos; or zirconium.&apos; Observed, however, was an initial difference in the absolute value of the flow stress below 320oK, Fig. 1. Grain size may account for the difference; the grain diameter of Ferrovac E was 30 to 45 µ and that of Ferrovac E-0.15 pct Ti 65 to 90 µ. Although second phase particles in the form of titanium carbides and nitrides precipitated in the Ferrovac E-0.15 pct Ti alloy, the spacing was too large to produce any strengthening effect. The mechanical properties measured, therefore, were inherent to the bcc lattice. 1W. C. Leslie and R. J. Sober: Trans. ASm, 1967, vol. 60, pp. 99-111. 2 H. Conrad: Journal of Metals, 1964, vol. 16, pp. 582-88. 3 A. S. Keh and W. C. Leslie: Materials Science Research. H. H. Stadelmaier and W.W.Austin, eds., vol. 1.pp. 208.50, Plenum Press, New York, 1963. 4A. S. Keh, Y. Nakada, and W. C. Leslie: Dislocation Dymmics, Rosenfield, Hahn, Bement, Jr., and Jaffe, eds., pp. 381-406, McCraw-Hill Book Co., New York, 1968. &apos;W. J. Bratina, J. T. McCrath, and H. E. Rosinger: Can. Met. Quart., in press. 6 W. J. Bratina, J. T. McGrath, and D. Mills: Suppl. Trans. Japan Inst. Metals. 1968, vol. 9, pp. 436-43. &apos;H. E. Rosinger and C. B. Craig: Can. Met. Quart., In press. %. Mills. J. T. McGrath. and W. J. Bratina: ScriptaMet,, 1968, vol. 2, pp. 311-13. The purpose of this note is to present the results of a direct measurement of the stacking fault free energy in copper. The present method avoids both the question of interaction forces of nodal dislocations and the assumption that the coherent twin boundary free energy is one-half that of a stacking fault. Fig. 1 shows a transmission electron micrograph of a stacking fault intersecting a high angle grain boundary in copper: Fig. 2 is a schematic representation of the intersecting interfaces. To produce the specimen, pure copper was rolled to 0.002 in. thickness and annealed for several hours at 875°C. These foils were strained in tension to l04 µ in. per in., and rean-nealed to 8 min. Recrystallization and/or grain growth were not observed during the second anneal, indicating that intersections such as Fig. 1 are equilibrium configurations. Many such stacking faults were observed, but few were noted as intersecting grain boundaries in well-illuminated areas. The intersection of Fig. 1 was well away from the specimen edge. Since similar defects have not been observed in fully recrystal-lized and annealed copper, it is felt that this defect is due to the tensile straining. Electron transmission

Jan 1, 1970

NORTH AMERICA ALASKA Anchorage.-Neitzert, G. H. Strandberg, H. Candle.-Robbins, J. S. College.-Barber, R. J. Burns, W. T. Coats, R. R. Fox. E. F. Joesting, H. R. McAnerney, J. M. Colorado Station.-Beyer, A. Stanford, J. V. Douglas.-Cahill, W. E. Carlson, L. Fairbanks.-Crawford, J. D. Earling, R. B. Fowler, D. A. Greves, J. H. Henton, H. M. Herbert, C. F. Hopkins, J. E. Kreitlow, E. J. MacDonald, D., III Mathews, T. C. McCarty, W. J. McNair, W. H. Metcalfe, J. B. Mikami, H. M. Mize, R. J. CANADA ALBERTA Calgary.-Johnson, R. V. Link, T. A. Marple, L. E. Slipper, S. E. Thorne, B. L. Thorne, H. L. Vissac. G. A. Edmonton.-Ball, -M. W. Lilge, E. O. Pitcher, N. C. Nordegg.-Shanks, J. BRITISH COLUMBIA Allenby.-Lindsay, W. R. Bralorne.-Almstrom, A. A. Bosustow, R. Currie, J. M. Gibson, S. Schmitt, D. E. G. Wilson, G. H. Bridge River.¬Botterill, T. C. Crane, G. A.

Jan 1, 1939

By Chas. B. Dudley

A Discussion of the papers of Mr. James Gayley, on "The Application of the Dry-Air Blast to the Manufacture of Iron," and of Mr. J. E. Johnson, Jr., on "The Physical Action of the Blast-Furnace," by Messrs. Charles B. Dudley, R. W. Raymond, J. E. Johnson, Jr., William F. Mattes, James Gayley, David Baker, John Birkinbine and F. E. Bachman. (Washington Meeting, May, 1905.) CHAS. B. DUDLEY, Altoona, Pa.:-Pam not a blast-furnace man, and this always puts me it a disadvantage because I cannot go into the details of the making of iron and steel. I have not the experience, and have to take the statements of other people, so what I say regarding the subject of this paper is not in the sense of an expert. When I first heard of Mr. Gayley&apos;s experiments, I said to myself, " I fear they will result in failure, since, apparently, Mr. Gayley has forgotten one chemical fact, namely, that carbon does not combine with oxygen in the absence of water-vapor." This fact which was so astonishing when it was first brought out some years ago, and which those who are interested may find in the Journal of the Chemical Society of London, for 18S5, page 349, and 1894, page 611, led me to think that the drying of the air would be a mistake. The general subject of the influence of water-vapor on chemical action is a large one; but the special point in which we are for the moment interested, namely, the influence of water-vapor on the combustion of carbon, was especially treated by Mr. H. B. Baker, in the papers referred to. Apparently, however, as the result of Mr. Gayley&apos;s experiments, we are to learn that the amount of moisture still left in the desiccated air is sufficient to secure perfectly satis¬factory combustion. In thinking over Mr. Gayley&apos;s paper, it occurred to me that there were two alternatives, either of which might be chosen, namely, we might dry the air as Mr. Gayley does, or possibly we might, in a very much simpler way, simply saturate the air at a constant temperature, and thus get uniform working and

Sep 1, 1905

By David Cole

AT the time flotation appeared upon the metallurgical horizon in Arizona, the writer, under the direction of Dr. Ricketts, was engaged in remodeling and enlarging the No. 6 Concentration Plant of the Arizona Copper Co. at Morenci, and the work had been in progress nearly a year before the Inspiration experiments with flotation had disclosed the revolution in concentration that was at that timè impending. The simplified flowsheet worked out for the remodeling of the Morenci plant had been based upon the removal of the freed metal in a minimum number of stages by treatment upon tables equipped with Butchart riffles, the latter being adapted to accomplish both classification of feed and removal of the metal at one operation, substantially as described in my previous paper.1 The scheme of treatment for the slime was based upon the well-known fact that after copper sulphides, such as chalcocite and chalcopyrite, etc., are reduced to a certain extremely fine state of comminution they are definitely beyond the reach of separation upon any of the concentrating devices then known. By using drag-belt classifiers (which served as conveyors as well as separators), the overflow would be of the usual "slimes" class. Experiment had shown that when these drag-belt overflows were, properly diluted (that is, to about 5 to 7 per cent. solids in the feed under treatment) . the very fine sand, and especially the very fine but still granular sulphide particle&apos;s, would, if given a short distance to fall, quickly settle out in prime condition to yield an excellent recovery on vanners; a further valuable feature would be that the very fine non-separable final overflow tonnage might be discharged direct to tailing, thus conserving space requirements so as to permit within the old building, without embarrass-ment, the increase of capacity required.

Jan 9, 1916

By John L. Boardman

THE Anaconda company has never indulged in any employee activities at Butte which might be termed paternalistic, but it has exerted a vast amount of effort in care of its employees during working hours. The reason for this policy is not lack of interest or that the company does not feel the effect of employees&apos; activities while they are "off the job"; it is that the company and the city of Butte have grown up together and each has been adequate in its own sphere, the company in providing employment at the highest possible wage and the city in providing housing, sanitation, commercial services, medical services, schools, churches, amusements and entertainments. The one exception to this independence between the company and the community is the Butte Water Co., which is a wholly owned subsidiary of the Anaconda Copper Mining Co. Mention of this relationship is made here because the water supply of such a city as Butte is one of the principal factors in determining the health of the people. Very early in the development of the Anaconda company an adequate and dependable water supply for the operations became necessary, therefore the company took over this important community function. So well has this activity worked out that during the whole period of time covered, in which the company has expanded to become practically the sole mine operator and the community has grown from a small mining camp to the status of a modern city, there has been no shortage of water or any outbreak of water-borne, epidemic disease. CONDITIONS LEADING TO ORGANIZED SAFETY EFFORT A brief sketch of conditions in Butte prior to 1912 is necessary to an understanding of the reasons for placing accident prevention on an organized basis. As early as the year 1884 there were a large number of small independent mining operations depending principally upon the production of silver, although even then copper was becoming prominent in the value of total production for the district. The Butte camp was then just emerging from the log cabin stage to that of a modern city.

Jan 1, 1938

By G. Derge, R. E. Grace

Diffusivity of bismuth in liquid Pb-Bi alloys has been measured by the capillary reservoir method as a function of temperature and composition. Fair agreement between theory and experiment is found for the measured diffusion coefficients and activation energies of diffusivity and viscosity in dilute lead alloys. The measured diffusion coefficients in the high bismuth alloys describe mass transport in special concentration gradients. THE study of diffusion in liquid metals has been restricted largely to the amalgams over small ranges of temperature and composition. In contrast to this, diffusion and transport of ions and molecules in aqueous and organic solvents have been studied extensively for the past 50 years. The general difficulty of measuring diffusion coefficients in both gases and liquids at high temperatures has been that of eliminating convection currents. Measuring techniques based on freezing and sectioning after the diffusion period1 are not particularly satisfactory because of the volume changes and segregation which occur during freezing. The most promising technique which is currently being developed for liquid metals is the capillary reservoir method. This eliminates convection currents from the diffusion zone and requires measurements only of the length and initial and final compositions of the alloy within the capillary. Anderson and Saddington&apos; have measured the diffusion coefficient of tungstate anions in aqueous Na,W04; Wane4&apos; and Hoffman- ave studied structure and self-diffusion in water and self-diffusion in mercury, respectively, by similar techniques. Selection of the Pb-Bi system for initial study was made for several reasons: I—It afforded a low temperature system for development of techniques which would be suitable for high temperature measurements in liquid iron. This research on diffusion in liquid iron is now in progress as a part of a general program on the rates and mechanisms of slag-metal reactions. 2—Activity data on liquid Pb-Bi alloys of all compositions are available from the emf meas- urements of Strickler and Seltz.9 3—Some data are available on the diffusion of bismuth into solid lead. The measurements on solid alloys were made by von Hevesy and Seith7 for the concentration range of 0 to 2 pct Bi. An appropriate solution to Fick&apos;s law (unsteady state) for the capillary reservoir has been found by considering the mass flow which passes through a unit area of surface on a slab of infinite thickness as a function of time. This is the first application of this solution to diffusion measurements, although a similar solution is available for identical boundary conditions.&apos; By analogy with heat conduction, the problem reduces to a perfectly insulated infinite slab at temperature C,, one surface of which is quenched to C, for all times, t. Heat is permitted to flow from quenched surface of the slab to an infinite supply of coolant at C.&apos; (see Appendix). For the corresponding solution for diffusion in liquids, these terms become Where Cu is the initial concentration of component A" in entire capillary at t - 0, C, is the final con- In this case. component A is bismuth, and C, = 0. centration of component A in entire capillary at t = t, C, is the concentration of component A in bath for all t, 1 is the length of the capillary in centimeters, t is the time of diffusion period in seconds, and D is the diffusion coefficient in square centimeters per second. By comparison with solutions to Fick&apos;s law used in the solid state, this solution for liquids is similar to the Grube solution for solids, where the change in D with chemical composition is not taken into consideration. Difficulty is to be expected if large concentration gradients are employed and if the concentration gradients extend over an appreciable length of the capillary.

Jan 1, 1956

Stringent controls now placed on the quality of coal make it important to be able to predict not only the tonnage and the grade of the coal in situ, but also the recovery factory and average grade after the coal has been washed. The established techniques of linear geostatistics (ordinary kriging) can be used to estimate the total tonnage and the grade of the coal in situ, but more sophisticated techniques are required for predicting the characteristics of washed coal. Two approaches are currently being investigated at Fontainebleau. One involves a parametric model of the washability curves and disjunctive kriging. This is described in Armstrong (1980(a) and (b)). The other is similar to the service variable approach used for estimating recoverable uranium reserves. The method is described in this paper.

Jan 1, 1985

By J. L. Walter

Extra-low carbon iron sheet, when deformed and annealed, undergoes exaggerated or abnormal grain growth in the critically deformed regions of the sheet. This exaggerated pmth occurs, for low strains (3 to 6 pct), only in sheet which has a fine dispersion of precipitates in the subsurface region of the sheet and fewer and coarser precipitates in the sheet interior. These particles have been identified as manganese sulfides. Wing the anneal, grains near the surface are gvowth-inhibited by the fine particles but the grains in the interior are free to grow normally. With the additional driving force provided by the strain energy, the interior grains first grow into the small subsurface pains. Eventually, these growing grains grow completely through the sheet. Calculations of limiting grain sizes at various values of strain indicate that a volume fraction of precipitates in excess of 10-&apos; would be required to eliminate exaggerated growth in material strained to 10 pct. OPEN-COIL annealing has made decarburization of sheet steel both efficient and economically practical. Use of such material for porcelain-enameling stock is one of many possible applications of low-carbon iron since carbon in steel is deleterious to porcelain-enameling properties.&apos; However, the extra-low carbon iron presently available presents another problem, that of exaggerated grain growth in regions where the sheet has been deformed as by bending or stretching. In exaggerated grain growth a few grains start to absorb their neighbors and these may become very much larger than the average grains of the sheet. Other names for exaggerated grain growth are coarsening, critical grain growth, secondary recrystallization, abnormal grain growth, or discontinuous grain growth. While this grain growth does not affect the enameling qualities of the low-carbon iron sheet, their presence results in a marked reduction of tensile-yield strength in the region of the sheet containing the large grains. The loss of tensile yield strength may render the material unsuitable for many applications . This report describes the results of a study undertaken to determine the cause of the exaggerated grab growth in extra-1ow carbon iron and, if possi- ble, to prescribe practical procedures for its prevention. GENERAL THEORY The driving force for exaggerated grain growth is the grain boundary free energy. This driving force is proportional to (l/rl + l/r2) where rl and r2 are the mutually perpendicular radii of curvature of the boundary between the growing grain and the grain being consumed. Thus, the greater the difference in size between the growing grain and the matrix grains, the higher the driving force for grain growth. If, however, the matrix grains are free to grow simultaneously, the driving force for exaggerated growth will be diminished. Stability toward growth of the matrix grains may be caused by a) a strong single orientation texture (texture inhibition),&apos; b) a dispersed second phase,3"5 c) the thickness effect,&apos; or d) intergranular segregation.7"9 As exaggerated growth occurs when growth of the matrix grains has been slowed by the stabilizing processes mentioned above, there must be an additional factor acting to promote growth of a few of the grains to the point where they are enough larger than the matrix grains that boundary energy driving forces are sufficient to cause continued growth. For instance, at the annealing temperature, growth-inhibiting inclusions may slowly dissolve and coalesce. Eventually, a grain boundary becomes unlocked and migration occurs at the expense of neighboring grains. Or, an additional driving force may be supplied to some of the grains if the material is strained. Then, since some grains will be strained less than others, the difference in strain energy between adjacent grains may be sufficient to overcome boundary locking and allow growth of the grains with lower strain energies. In the present study, therefore, such factors as the presence or absence of dispersed phases, the nature of the exaggerated growth, and the effect of strain have been considered. EXPERIMENTAL PROCEDURE I) Material and Processing. Three types of low-carbon iron were used in this study; types A and B were commercial grades, each from a different supplier.* The precise details of the processing of

Jan 1, 1963

By Irving Cadoff, Kurt Komarek, Edward Miller

THE lead-telluride phase diagram as compiled by ansen&apos; has one intermetallic compound, PbTe, with solid-solubility limits extending from 22 to 45 wt pct Te (31.4 to 57.1 at. pct). Pelzel2 redetermined the solubility limits on the lead-rich side of the compound by measuring the relative areas of the two phases in samples annealed in the liquid + compound region, and obtained data that agreed with that of Hansen. Recent studies of the semiconducting properties of PbTe3 however, have indicated that addition of either lead or tellurium to PbTe does not produce samples having carrier concentrations greater than about 10 19 cm-3. Assuming that each impurity atom results in one ionized charge carrier, this carrier concentration corresponds to a solubility range of less than 0.04 at. pct. Fritts and Karrar4 have also observed two phases in samples containing from 0.15 to 3.0 pct excess Pb. To resolve the discrepancy between these data, the solid solubility limits of the compound PbTe were reinvestigated, using several other techniques. Ten 25-g samples with compositions of 1/2, 1, 3, 5, and 10 wt pct excess Pb and Te and two 100-g samples of 15 and 65 wt pct Te were prepared, sealed in evacuated quartz capsules, and melted at 950oC. The 1 pct excess Pb and Te and the 15 and 65 wt pct Te alloys were homogenized for 96 hr at 450°C; the remaining specimens were annealed 50°C below the solidus temperature reported in Hansen. The specimens were polished and etched with dilute HNO,. All the samples were two phase, the second phase appearing at grain boundaries or as spheroidized inclusions in the grains. In the case of the tellurium rich specimens, the second phase could be identified as a eutectic. Debye-Scherrer powder diffraction patterns of the i, 1, 3, 5, and 10 pct excess samples were obtained using CuKa filtered radiation. The films were indexed as the B1 or NaCl structure. The calculated lattice parameter of PbTe was the same for all the specimens, with an average of a0 = 6.460 ± 0.0005A. Lines due to excess lead or tellurium were very faint but could be clearly seen in all the films. The relative areas of the two phases in the 15 and 65 wt pct Te samples were corrected for the differences in density of Pb, Te, and PbTe, and taken as proportional to the relative volumes of the two phases. The corrected relative volumes agreed with a phase diagram having negligible solubility of both lead and tellurium in lead tellurium. The density of the two specimens was obtained to give a third independent determination of the phase limits. The specimens were broken into small pieces to eliminate any internal porosity, and adherent air bubbles were removed by vigorous shaking under water for several hours. The density of lead (11.34 g per cm3) and of tellurium (6.25 g per cm3) was taken from the International Critical Tables and that of stoichiometric PbTe (8.25 g per cm3) calculated from the lattice parameter. For the 15 wt pct Te samples, the density assuming no solubility was calculated to be 9.89 g per cm3; the observed density was 9.86 g per cm8. For the 65 wt pct Te alloy, the density calculated for the case of no solubility was 7.24 g per cm3; the measured density wag 7.22 g per cm3. These results are consistent with those of planimetry and X-ray. SUMMARY Data have been presented which show that the solid solubility of both lead and tellurium in PbTe is

Jan 1, 1961

By J. Philibert, A. G. Guy

Diffusion in the presence of deformation was studied by the method of vacuum dezincification of copper-rich and silver-rich solid solutions containing 7 to 30 pct Zn. The specimens were designed to permit the study of diffusion in separate portions of a given specimen characterized by strain rates ranging from essentially zero to approximately 10 sec-. No effect of deformation on diffusion was observed. BEGINNING with the work of Buffington and Cohen: interest in the question of the effect of stress or strain on diffusion has largely been concentrated on the enhancement of diffusion in specimens subjected to Continuous plastic deformation. The present research is a contribution to this limited area. However, as a preliminary to focusing attention on this special topic, it will be desirable to make a broad survey of the larger question, especially since there has been considerable foreign work in areas outside those of current interest in the United States. Since most of the topics referred to in the following section are both complex and imperfectly understood at present, it has been expedient in most instances to offer only a guide to the general nature of the work rather than a critical evaluation. PREVIOUS WORK The effect of elastic stress on diffusion has received considerable attention, especially with regard to the thermodynamic driving force for diffusion. The thermodynamic treatments have been based on the work of Gibb, Voigt, Planck, and Leontovich.&apos; Konobeevskii and Selisski6 made a first attempt at treating the problem in 1933, and Gorskii7 a few years later gave a solution applicable to single crystals as well as to polycrystalline specimens. In 1943 Konobeevski8 published treatments that have been the basis of much Russian work up to the present. For example, Aleksandrov and Lyubov used his work in explaining the velocity of lateral growth of pearlite. Early work in the United States was that of Mooradian and Norton, which showed that lattice distortion tends to be relieved before it can significantly affect the diffusion process. Druyvesteyn and Berghoutl1 observed a slight effect of elastic strain on self-diffusion in copper, while de Kazinczy12 found that both elastic and plastic deformation increased the rate of diffusion of hydrogen in steel. On the other hand, Grimes58 observed no effect of either elastic or plastic straining on the diffusion of hydrogen in nickel. High-frequency alternating stresses have been reported by various investigator s13-l5 to increase the rate of diffusion. A special form of elastic stressing is the imposition of hydrostatic pressure, a condition that is amenable to Conventional thermodvnamic analysis. Most of the experimental results in this area are consistent in showing a slight decrease in diffusion rates at high pressures.16-l8 Although Geguzinl reported a pronounced effect of relatively small pressures, Barnes and Mazey20 failed to Corroborate this finding, while Guy and Spinelli21 advanced an explanation of the phenomenon observed by Geguzin. It has been recognized that the thermodynamic treatment of diffusion phenomena in an arbitrarily stressed body is complicated by the fact that the desired state of quasi-equilibrium of the shear stresses cannot be maintained during a general diffusion process. However, attempts have been made by Meix-ner22-24 and Fasto to treat certain restricted cases, such as relaxation. FastovZ7 has also incorporated the general stress tensor into the thermodynamics of irreversible processes. The lattice strain that accompanies the formation of a solid solution has been the subject of much study,28-s0 and indirectly it has entered into many recent theories of diffusion. However, some Russian investigators31&apos;32 have taken other views of this matter and have predicted large effects on diffusion rates because of concentration stresses.o In completing this brief resume of previous work involving elastic strains and before proceeding to a consideration of the effect of continuous plastic deformation, it should be pointed out that deformation of various additional types may also influence diffusion. The effect of cold-working on subsequent diffusion has been studied directly by AndreevaS and by Schumann and Erdmann-Jesnitzer, while indirect evidence has been obtained by Miller and Guarnieri and by Vitman.38 Thermal stresses may also influence diffusion, contributions to this subject having been made by Fastovs7 and by Aleksandrov and Lyubv. The work of Johnson and Martin,o Dienes and Damask,3Band DamaskS considered the question of radiation-enhanced diffusion. In considering previous work on the subject of plastic deformation and diffusion, attention will be directed to those studies concerned primarily with diffusion rather than with its relation to Creep, e.g., the work of Dorn, or to the acceleration of diffusion -controlled reactions. Observations of the effect of

Jan 1, 1962

By Richard F. Hinds, F. O. Reudelhuber

Application of the conventional depletion drive calculation methods to volatile oil reservoirs results in erroneous estimates of ultimate recovery. In view of the increasing number and importance of volatile oil reservoirs, a special technique has been developed which will result in more realistic predictions using laboratory data obtained from reservoir fluid studies of a specific type. The experimental data are designed to permit continuous material accounting and, therefrom, provide the hy-clrocarbon composition of both the flowing oil and gas phases. The resultant well-stream composition data are then used directly in surface recovery calculations utilizing equilibrium ratios. A step by step procedure, specifically designed for routine use by the practicing reservoir engineer, is presented in an appendix. An actual study performed on a deep Mid-Continent reservoir is used ay an il-lustrathe example. INTRODUCTION It has been a practice for many years to utilize the conventional ma- terial balance methods in conjunction with relative permeability concepts for the prediction of recovery from solution gas drive reservoirs.&apos; Those who have performed such calculations recognize that compromises of several types are necessary in order to reduce the calculations to a reasonable degree of complexity. The most serious assumption involved results from the necessity of treating the produced oil and gas as separate fluids, independent of each other in their behavior. It is further assumed that the gas which is evolved in the reservoir as a result of pressure decline will not yield liquid upon the reduction of pressure and temperature resulting from production through surface equipment. Although these shortcomings have been recognized,&apos; it has been difficult to attempt refinement of calculation procedures since the laboratory data available normally were not of the proper type or extent to permit such calculations. Three general procedures have been available for depletion drive calculations when laboratory fluid data are of the conventional type. Differential Procedure The most simple, and most widely used, method requires use of the formation volume factor and gas sol- ubility data obtained from a differential liberation performed at reservoir temperature. This procedure ignores the differences existing between the fluid behavior in the reservoir and its behavior as it is produced through surface separation equipment. The errors introduced are not serious when dealing with very low volatility fluids and this method may be utilized if the laboratory data indicate only slight differences between the differential data and the flash data obtained from separator tests. Modified Differential Procedure This method was developed when it became apparent that medium volatility fluids evidenced a wide difference between the flash and differential data. The differential data are adjusted by changing from a residual oil basis to a stock tank oil basis. All that is required is multiplication of the differential data by the ratio of residual oil to stock tank oil relative volumes existing for the original reservoir fluid at the determined saturation pressure. This procedure generally results in increased calculated ul-timate recovery; however, such results should be viewed critically. Upon examination it may become apparent that the results are influenced by errors in reservoir liquid

Jan 1, 1958

By Charles H. Jones

Jan 1, 1905

By Max W. Ball

THE geologist or mining engineer, whose work takes him into the western United States, whether for the Government or private enterprises, is likely to be called upon to classify public lands as to their mineral character, or to review such classification already made, usually by a Government geologist or mineral inspector. The public-land law covering the matter is clear and logical, and a knowledge of its simpler principles is necessary to intelligent classification work. There are two classes of cases in which a classification of lands as mineral or non-mineral may be required: .first, cases in which lands classified as mineral will be retained by the Government and lands classified as non-mineral alienated; second, cases in which lands classified as mineral will be alienated and lands classified as non-mineral retained.

Jan 1, 1921

By A. Gemperle

Electron diffraction and transmission electron microscopy on foils at room temperature were used to investigate the ordering of Fe-Si alloys containing 10 to 23 at. pct Si. A certain degree of DO3 order was found in all alloys. With the exception of the lowest silicon concentration for which the antiphase domains could not be clearly resolved, the alloys have a domain structure of two-domain type with boundaries having 1/4a01<111> displacement vectors for less than 12.3 at. pct Si and with boundaries having 1/2 a0<100> displacement vectors for more than 12.3 at. pct Si. The alloys with 12.3 at. pct Si have a domain structure consisting of fine domains with 1/2a&apos;o<100> boundaries within much larger domains with 1/4a&apos;o<111> boundaries. The development of these structures can be explained by transition of the alloy from the disordered state into the B2-type order and then into the D03-type order by the mechanism proposed previously for the FeSAl alloys. The existence of the B2 structure in the lower part of the investigated concentration range reported in some articles can be explained by fine domains with 1/2a&apos;o<100> boundaries formed by several disordered planes within large domains with 1/4a&apos;o<111> boundaries. The ordered structure predicted by the theory —with practically no domain boundaries —is found in the alloys having 12.3 at. pct Si where it develops in the B2 structure region. ORDERING in Fe-Si alloys was first studied by phragmenl who found that beginning with 13 at. pct Si the DO3 (Fe3Si) superlattice reflections appear in the diffraction patterns. The equilibrium diagrams constructed later by corson2 and Haughton3 from various measurements proposed the existence of a homogeneous solid solution (a phase) in the range from 0 to 25 at. pct Si. Jette and Greiner4 and Farquhar et al.5 measured the relation between lattice parameter and composition and they considered the break in the curve at 9 to 10 at. pct Si to be caused by the ordered solution a"(Fe3Si). Glaser and Ivanick6 Determined critical ordering temperatures of the alloys containing from 10.9 to 27.9 at. pct Si from the measurement of the electric resistivity of quenched samples. In all cases the critical temperature was lower than the melting point and it was highest for 25 at. pct Si. Lihl and Ebel7 measured the lattice parameter curves at various temperatures up to 1000°C. The region between two breaks on these curves, corresponding to 10 to 12.5 at. pct Si at room temperature, was considered by them to be two-phase (a + a"). They concluded by extrapolation of the measured values that a" in the alloy having 25 at. pct Si is stable up to the melting point. Davies8 studied superlattice reflections in the X-ray diffraction patterns of an alloy containing 8.7 at. pct Si. He found the B2 structure and short-range order in the slowly cooled samples and the DO3 A. GEMPERLE is Research Scientist, Institute of PhysicS, Czechoslovak Academy of Sciences, Prague, Czechoslovakia. __Manuscript submitted January 2, 1968. IMD structure in the quenched and annealed samples. This investigation first reports the presence of the B2 structure, phase a&apos;: in Fe-Si alloys. Meinhardt and krisement9,10 also found its existence in Fe-Si alloys by neutron diffraction. No order was detected by them in the alloy containing 8 at. pct Si. The onset of B2 order was observed at a composition of 9.2 at. pct Si. They found almost perfect B2-type order with partial DO3-type order at room temperature in the 10 to 12.5 at. pct Si range and almost perfect DO3-type order in the 12.5 to 25 at. pct Si range. They established the critical temperatures Tc of both the structures through measurement at higher temperatures. The critical temperature for the B2 structure was found to be always higher than the critical temperature for the DO3 structure of the same alloy. They extrapolated the curves of the critical temperatures and concluded that the alloys with more than 17 at. pct Si have the B2 structure up to the melting point and the alloys with more than 23 at. pct Si have the DO3 structure up to the melting point. The results of Meinhardt and krisement9,10 were confirmed by Dokken&apos;s measurement" of the temperature dependence of the electrical resistivity in the 10.8 to 15 at. pct Si range. On the other hand chessin12 detected by X-ray diffraction a considerably lower degree of order in the 12.7 at. pct Si alloy. ANTIPHASE DOMAIN STRUCTURE IN ALLOYS WITH B2- AND DO$-TYPE ORDER The ordered structures B2 and DO3 can be described in terms of a subdivision of the bcc lattice into four fcc sublattices with a parameter double that of the bcc lattice. Following Marcinkowski13 we will label them I. 11, 111, IV. The B2 structure in the AB alloy is formed by placing A atoms on sublattices I and II and B atoms on sublattices III and IV. In a non-stoichiometric perfectly ordered alloy having concentration (A) > (B), A atoms occupy sublattices I and 11. and A and B atoms distributed at random occupy sublattices III and IV. The DO3 structure in an A3B alloy is formed by placing A atoms on sublattices I, 11, and 111, and B atoms on sublattice IV. In a nonstoichiometric, perfectly ordered alloy having concentration (A)/3 > (B), A atoms occupy sublattices I, 11, and 111, and A and B atoms distributed at random occupy sublattice IV. As further shown in Ref. 13, two types of domains are possible in the B2 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4 a&apos;o<ll1> only. Four types of domains are possible in the DO3 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4a&apos;o<111> and 1/2a&apos;o<l00>. Bethe14 suggested on the basis of theoretical considerations that in a structure with two sublattices at low temperatures only one domain should be present in the whole crystal at equilibrium. Similarly Bragg15 concluded that at low temperatures the domain struc-

Jan 1, 1969

By AIME AIME

DESTRUCTION of the plants, machines, utilities, tools, materials, and other essentials for peacetime living penalizes not only the owners of the materials destroyed, but the world as a whole. Specifically, the fundamental fallacy of any proposal for the in- discriminate destruction of the German industrial system is that it fails to differentiate between the wartime and the peacetime economy of the Reich. We are for one simple, clear objective-an effective industrial means to keep Germany from starting another war. This objective should not be con- fused, especially before the war is even won, with the appropriate punishment of Germany or with the international arrangements for the long future to be made around the peace table by the representatives of the Allied Nations after victory is achieved. This paper, therefore, does not deal with broad, complex postwar questions of diplomacy and international policy. "Unconditional surrender" implies disarmament of the German armies, the surrender of all arms, munitions, air- planes, and other ordnance material in stock piles or in process. It also should include the elimination of all German war production facilities, such as ordnance plants, munitions plants, and submarine works, and the control of raw materials required by war industries.

Jan 1, 1944