Search Documents

By Claudio Barsotti, Leonard C. Kitchener

INTRODUCTION The major mining operations of the Ontario Division of Inco Metals Company are located in the Sudbury Basin. Around the rim of this geo- logical formation and within thirty miles of the City of Sudbury are located eleven under- ground mines of the Company, two of which are on standby. In addition, there is one mine in Northwestern Ontario at Shebandowan, 1127 Km (700 miles) northwest of Sudbury. In 1980 ore production totalled 10.6 x 10 mt (11.7 million tons) from underground and open pit operations. Underground mining methods include blasthole, vertical retreat, sublevel caving, cut-and-fill and undercut-and-fill. Inco reduction operations in the Sudbury area include two concentrators, one smelter, one iron ore recovery plant, a copper refinery a nickel refinery and a high purity plate rolling mill. As well, an electrolytic nickel refinery is located on Lake Erie at Port Colborne, near Niagara Falls. In the Sudbury District, Inco employees total 14,278 of whom 6,490 are directly employed in the mining and milling operations. I T H DRILLING Background - The use of long blastholes in underground operations at Inco mines in the Sudbury district started more than 30 years ago at the Levack Mine. At that time, diamond drills were used to mine ore by open stoping and for pillar recovery. By the 1950's the concept had been extended to all mines. The heavy percussion drill was also developed by this time and led to the acceptance of the 11.43 cm (4% in.) piston diameter drifter for bar and arm and fan drill applications. The use however, of the nominal 5.08 cm (2 in.) diameter blastholes drilled radially from the level or sublevel causes overdrilling at the periphery. As well, the smaller holes are subject to hole deviation, are difficult to drill beyond 38.1 m (125 ft.) and require the need for several drilling horizons or sublevels. The need to improve blasthole stoping techniques and our experience with large diameter blastholes in open pit mining led to the trial of an I T H drill in 1962. The test was unsuccessful however, since button bits were not available at the time and the tungsten carbide cross bit experienced short life, gauge loss, and caused hole deviation and poor penetration rates. The successful application of the raise borer beginning in 1964 and the ability to drill 20.32 cm (8 in.) to 27.94 cm (11 in.) diameter pilot holes led to the development of smaller, more portable, rotary drills for blasthole mining. As a result, a mining method based on the use of 20 cm (7 718 in.) diameter, 60.1 m (200 ft.) long rotary blastholes was developed and tested successfully at our C.C.North Mine. Between 1972, when the method was first tested, and 1973 over 4572 m (15000 ft.) of large holes were drilled with rotary drills in the recovery of 175,960 mt (194000 tons) of primary stoping and pillar remnants. A new mining method was developed that made use of this large hole drilling equipment. Instead of longhole carbide drilling by bar-and-arm or fan drill set-ups at sublevels, the large diameter holes were drilled full stope height from the top sill, which substantially reduced development, drilling time and improved fragmentation. These drills however, were difficult to move and set-up, and had a high maintenance cost and low productivity. The capital outlay and extensive technical development required to improve these drills and reduce the high drilling costs however, was economically unattractive. New development in drills and button bits INTRODUCTION The major mining operations of the Ontario Division of Inco Metals Company are located in the Sudbury Basin. Around the rim of this geo- logical formation and within thirty miles of the City of Sudbury are located eleven under- ground mines of the Company, two of which are on standby. In addition, there is one mine in Northwestern Ontario at Shebandowan, 1127 Km (700 miles) northwest of Sudbury. In 1980 ore production totalled 10.6 x 10 mt (11.7 million tons) from underground and open pit operations. Underground mining methods include blasthole, vertical retreat, sublevel caving, cut-and-fill and undercut-and-fill. Inco reduction operations in the Sudbury area include two concentrators, one smelter, one iron ore recovery plant, a copper refinery a nickel refinery and a high purity plate rolling mill. As well, an electrolytic nickel refinery is located on Lake Erie at Port Colborne, near Niagara Falls. In the Sudbury District, Inco employees total 14,278 of whom 6,490 are directly employed in the mining and milling operations. I T H DRILLING Background - The use of long blastholes in underground operations at Inco mines in the Sudbury district started more than 30 years ago at the Levack Mine. At that time, diamond drills were used to mine ore by open stoping and for pillar recovery. By the 1950's the concept had been extended to all mines. The heavy percussion drill was also developed by this time and led to the acceptance of the 11.43 cm (4% in.) piston diameter drifter for bar and arm and fan drill applications. The use however, of the nominal 5.08 cm (2 in.) diameter blastholes drilled radially from the level or sublevel causes overdrilling at the periphery. As well, the smaller holes are subject to hole deviation, are difficult to drill beyond 38.1 m (125 ft.) and require the need for several drilling horizons or sublevels. The need to improve blasthole stoping techniques and our experience with large diameter blastholes in open pit mining led to the trial of an I T H drill in 1962. The test was unsuccessful however, since button bits were not available at the time and the tungsten carbide cross bit experienced short life, gauge loss, and caused hole deviation and poor penetration rates. The successful application of the raise borer beginning in 1964 and the ability to drill 20.32 cm (8 in.) to 27.94 cm (11 in.) diameter pilot holes led to the development of smaller, more portable, rotary drills for blasthole mining. As a result, a mining method based on the use of 20 cm (7 718 in.) diameter, 60.1 m (200 ft.) long rotary blastholes was developed and tested successfully at our C.C.North Mine. Between 1972, when the method was first tested, and 1973 over 4572 m (15000 ft.) of large holes were drilled with rotary drills in the recovery of 175,960 mt (194000 tons) of primary stoping and pillar remnants. A new mining method was developed that made use of this large hole drilling equipment. Instead of longhole carbide drilling by bar-and-arm or fan drill set-ups at sublevels, the large diameter holes were drilled full stope height from the top sill, which substantially reduced development, drilling time and improved fragmentation. These drills however, were difficult to move and set-up, and had a high maintenance cost and low productivity. The capital outlay and extensive technical development required to improve these drills and reduce the high drilling costs however, was economically unattractive. New development in drills and button bits

Jan 1, 1981

By Edward S. Cook

For several years past, dating particularly from the days of serious "ore-dirt" complications at the Warwick furnace, I have been desirous of providing some safe, quick and easy method of relieving the tuyeres of slag, when the cinder- and iron-notches are chilled through loss of heat in the clucible or when, from dropping or jumping of stock, the molten slag is forcibly driven into the bellyand leg-pipes. Various methods were proposed, but objections of one kind or another always presented themselves, and the subject was postponed to a more convenient season. In the summer of 1887, while running on anthracite alone, 1 found the various expedients in use to be so utterly valueless, that the importance of a practicable tuyere slagging-valve impressed me more forcibly than ever. The holes left in the cast-iron jacket at one side of the bottom of the water-blocks were found to be of no value whatever. The swinging or hinged cap on the elbow of the belly-pipe, while convenient to permit the removal of lag after the belly-pipe was partially or wholly filled, could not be adapted to discharge the slag before solidifying, except at great risk to the men and loss of time just when the constant running of the engine and the keeping of blast on the furnace was of the utmost importance. By removing keys from the caps and holding them in place with props, the slag could be discharged through the tuyeres and belly-pipes, with the engine running, by knocking the props away at a given signal. This method is extremely hazardous to life and limb, and I have always hesitated to make use of it. When the furnace is in such condition as to require the adoption of some method of the kind, the stoppage of the engine, cooling the blast and the contents of the crucible, always aggravates the trouble. When the caps are blown open and the slag is discharged by removal of the props, it is necessary to stop the engine to replace them. An hour or more will elapse before this can be done, as the slag must be partly removed before the tuyeres can be approached by ordinary mortals, and the caps handled and fastened in place again. Any movement of the stock is liable to burn the workman, as he stands, securing the cap in front or at one side of the open belly-pipe.

Jan 1, 1889

By Y. C. Liu, R. H. Richman

The effects of gel,manium and tin on the deformation and 9-e-crystallization textures of copper have been explored in detail with in the copper-rich terminal solid solutions. Addition of solute to copper produces a change in deformation texture from the copper type to the 70 :30 brass type. This transition has been measured quantitatively The types mid proportions of recrystal-lization components have been determined as a function of com-position, and correlation of recrystallization components with specific deformation components is discussed. On the basis of information available in the literature, it has been suggested that the effect of solute elements on the recrystallization texture of copper

Jan 1, 1961

Albin. B . R Billings. Mont . '28 Amnter . Nathan L 26 Broad St.. New York . N . Y . '28 Bache . Jules S 42 Broadway. New York. N . Y . '28 Borrett . C . P . 5338 Harper Ave .. Chicago. I11 '28 Baum . Frank G. . Cons . Hydro-Electric Engr Camel'. Shasta Co. . Cal. '23 Baylean, William S Russ Bldg .. San Francisco. Cal . '28 Bean, Louis H .. V.P.. Dwight P . Robinson & Co.. lnc 126 E . 46th St New York. N . Y . '28 Beatty . Roes J . 1106 First National Bank' Bldg .. Chicago . Ill . '28 Benwell . Oswald F . 110 Gilpin St .. Denver. 1310 . '28 Beymer. Albert 9.. V.P .. Keystone. National Bank Pittsburgh. Pa . '28

Jan 1, 1929

By John E. Miller

Unit Rig & Equipment Co., manufacturer of Lectra Haul trucks, is continually studying methods of reducing the operating costs of large haulage trucks. Reduction of haulage system operating costs is an important goal that equipment operators and equipment manufacturers constantly try to improve on. One of the most variable and important factors affecting operating costs is actual truck operating practices. An examination was centered on methods to optimize truck utilization. It was found that a very effective method of accomplishing this goal would be an automatic truck control (ATC) system to automatically control a fleet of haulage trucks in a predetermined pattern. Economic studies were conducted which showed a very favorable reduction in mine operating costs by use of an ATC system. In 1970, Unit Rig & Equipment Co., in conjunction with SAAB-SCANIA began preliminary development of adapting, for truck use, a proven automated control system, previously used for train systems, small trucks, and military target vehicles. In 1974, the first prototype system was installed on a Lectra Haul M-100 and tested extensively at Unit Rig's test track in Tulsa, OK. This truck and system were then displayed publicly at the 1974 convention in Las Vegas. In 1976, the system was redesigned for production to maximize reliability, ease maintenance, and to accommodate future control and-status reporting developments proposed for haulage trucks. The new design equipment was manufactured, and a full system test will be conducted in an actual open-pit mine for an extended period to evaluate reliability, compile economic data, and obtain application information to evaluate complete mine haulage system conversions to ATC. System Description The ATC system is designed to provide automatic control of all the vehicle functions normally accomplished by the vehicle operator. The basic system consists of the on-board control equipment and the wayside control equipment. The on-board equipment receives commands from the wayside equipment and controls all the truck functions. In addition, on-board sensors monitor all critical truck functions and provide instructions to the truck and system to assure safe operation. The wayside equipment consists of a buried guidewire, block control units and a central controller which provides predetermined signals to the on-board equipment for speed control, steering, and for auxiliary functions (dumping, horn, etc.) through the guidewire located in the truck's path. The wayside equipment also controls vehicle separation, system status, and provides truck location to a central display panel. The central control panel can vary the speed level signals over any segment and can also command an emergency stop to halt all the units. [Fig. 1] illustrates a typical ATC installation. If ATC is used in operations which require flexibility and mobility at the end of the ATC guidance network, the trucks can then be operated by either radio remote control or manually to complete their assigned functions.

Jan 1, 1982

By K. W. Nelson, John N. Abersold

INDUSTRIAL hygiene has been defined by Patty' as "the science and art of recognizing, evaluating, and controlling potentially harmful factors in the industrial environment." This definition implies thorough study of operations, evaluation of potentially harmful factors through air sampling, micro-analyses and other means and finally, appropriate medical and engineering control wherever indicated. The prevention of industrial health injuries is a vital part of operations of American industry today. Progress and interest in this field has increased steadily for many years, the most rapid progress having been attained, perhaps, during the last three decades. It is significant to note that there are now official agencies in 46 states actively concerned with industrial health problems and that a western field station has been established recently in Salt Lake City by the U. S. Public Health Service to augment its industrial hygiene services directed from headquarters of the National Institute of Health, Bethesda, Md. Many of the larger industries have found it advantageous to establish their own industrial hygiene departments. The American Smelting and Refining Co. is a world-wide organization engaged in the mining, smelting, and refining of lead, copper, zinc, silver, gold, by-product metals, including cadmium, arsenic, and others. In the United States there are 13 smelters and refineries, 11 secondary smelters or foundries, and a number of mines. Approximately 9000 workers are normally employed. It has long been the established company policy to seek out occupational hazards and provide safeguards for employee health. Protective equipment has been supplied to individual workers and exhaust ventilation installations have been in use in some operations for more than 40 years. All of the major units have their own medical departments which provide employees with excellent medical and hospital care. In 1937 full scale industrial hygiene studies were undertaken at the Selby Plant and were extended to most of the other smelters during the next three years. In 1945 the Department of Hygiene was organized with Professor Philip Drinker of Harvard University as Director and with Dr. S. S. Pinto as Medical Director. The department is responsible for coordinating and maintaining a program for the good health of all employees from top management down to the lowest paid day worker. It is essentially a service organization serving all of the United States plants regardless of location or size. Full and part-time physicians employed in all of the company's American plants and working in close cooperation with the Medical Director are responsible for de- termining the state of health of all the employees and giving treatment when necessary. In general, medical care is confined to accidents or illnesses occurring while the men are on the job. Among the duties of the doctors is the making of careful physical examinations of new employees and routine check-ups of old employees. In addition to medical care a primary responsibility of the department is the prevention of occupational illnesses. In this the main concern is with the working environment in relation to its effect on the worker. Environmental factors may be dusts, fumes, gases, toxic materials, heat, humidity, radiation, or noise. The objectives are: (1) Immediate control of these factors through the education of the worker, through providing the wearing of respirators or other protective devices, and through careful medical examinations and regular analysis of urine specimens; (2) a long range control program which may be accomplished by local exhaust ventilation, wetting of materials, changes in metallurgy, changes in methods of handling, or by use of special devices and special equipment. To accomplish these objectives a fine industrial hygiene laboratory was built in Salt Lake City and equipped to do routine and experimental work. Trained and experienced industrial hygienists obtain the facts by making frequent hygiene surveys. These surveys include tests of the air, studies of all processes, and careful investigation of ventilation, lighting, and general working conditions. Except in emergencies, the air contaminants and often the substances handled by the worker are sent to the laboratory for analysis by chemists and technicians specially trained in industrial hygiene methods. The findings are evaluated in terms of limits recommended by various State and Federal agencies, and in light of all available medical data. The methods used for studying the working environment involve all of the usual chemical and physical procedures employed in industrial hygiene. The Impinger, electric precipitator, thermal pre-cipitator, and filter paper sampler have been used to collect atmospheric dust and fume samples. Of special interest here is the filter paper sampler, shown in Fig. 1, which was developed by Dr. Silver-man at Harvard University. The instrument has been improved and is used very extensively in field studies. A water manometer connected behind an orifice is used to determine the rate of air flow. Calibration is effected by use of a standard gas meter or rotameter. The dust or fume is collected on a filter paper clamped between two rings, as shown in Fig. 2. The filter paper, such as Whatman No. 52, collects both dust and fume with a very high efficiency. The instrument is very convenient and easily transported. The solids collected on the filter paper are analyzed in the laboratory usually by use of a polar-ographic procedure. By this procedure it is possible to measure quantitatively in a single analysis the

Jan 1, 1952

By T. C. Craig

For the year 1934, there were 382 oi1 wells completed for a total initial of 146,965 bbl. Fifty-three wells were deepened for a total increase of 8363 bbl., bringing the total volume of new oil to 155,328 bbl. As of Jan. 1, 1934, the daily potential of the field as determined by the Texas Railroad Commission was 159,740 bbl. Of this amount 26,429 bbl. is "marginal oil," and 2682 bbl. is exempt on account of water. In December, 1934, the daily potential was established by the Railroad Commission as being 297,501 bbl. with a daily allowable of 56,800 bbl. Of this amount 31,993 bbl. is "marginal oil," and 2183 bbl. is exempt on account of water. There has been no field-wide test made during the year, and as a result the rated potential of the field is in all probability much higher than the actual potential. As each new well comes in, a five-day test is made under the supervision of the Railroad Commission. The potential thus established is added to the field potential and shares its pro rata part of the market outlet, which is the allowable production, no allowance

Jan 1, 1935

By W. G. Matteson

I. Introduction...................................................... 436 (a) Extent of the Gulf Coastal Plain. (b) History of Important Gulf Coast Oil Pools. 1. Corsicans, Tex. 2. Spindletop, Tex. 3. Sour Lake, Tex. 4. Jennings, La. 5. Saratoga, Tex. 6. Batson, Tex. 7. Humble, Tex. 8. Caddo, La. 9. Vinton, La. 10. Naborton, La. 11. Red River, La. 12. Edgerly, La. 13. Goose Creek, Tex. 14. Damon Mound, Tex. 15. New Iberia, La. (c) Favorable Features of the Gulf Coast Pools. 11. General Topography and Physiography of the Gulf Coastal Plain.....440 111. General Stratigraphy of the Gulf Coastal Plain West of the 90th Meridian......................................................441 IV. Structural Types and their Characteristics.........................446 (a) hnticlinal Structure. (b) Structure of Salt Domes. 1. Domes of the Coast Prairie. 2. Domes of the Wold Region. 3. Recapitulation of Dome Structural Characteristics. V. Methods of Surveying and Prospecting............................. 454 VI. The Development of Salt Domes................- .................458 VII. Origin of Salt Domes...............4.............................461 (a) The Volcanic-plug Theory of Hager. (b) The Contemporaneous Sedimentation Theory of Norton. (c) The Theory of Upward Pressure Exerted by the Force of Growing Crystals, as Developed by Harris. VIII. Source of the Oil in the Gulf Coastal Pools.........................465 IX. Petrolific Value of the Salt Domes of the Wold Region..............467 X. Future Outlook.................................................. 467

Jan 1, 1918

By J. A. Harrison

The physical composition of coal and the distribution of its physical constituents will partially determine the efficiency of the process chosen for coal preparation. Distribution and concentration of coal macerals will, to a degree, be controlled by preparation processes. A number of preparation processes have been evaluated to determine this interrelation. These evaluations will help provide information needed for the production of coal that meets definite petrographic composition specifications. etrographic composition and degree of coalifica-tion of coal can determine the choice of cleaning processes and equipment used in coal preparation. The purpose of this paper is to present data on studies of the preparation processes of breakage, sizing, cleaning, and blending and to show the effect coal's petrographic composition has on these processes. Herrin (No. 6) and Danville (No. 7) Coals from Illinois were used in these tests. Nomenclature used herein is that approved in the Glossary of the International Committee for Coal Petrology,' based primarily on the Stopes-Heerlen system of classification2 and used in coal petrography laboratories throughout the world. BREAKAGE TESTS Breakage tests of Illinois coals related to petrographic composition have been conducted at various times at the Illinois State Geological Survey. These tests have been classified under two headings -impact tests and compression tests. Impact tests, as the name implies, consisted of breaking the coal by a sharp, sudden force. Impact tests were further divided into fall tests and block tests. Compression tests consisted of applying a constant pressure on a piece of coal until the coal fractured.

Jan 1, 1963

By R. J. Jackson, D. E. Williams, W. L. Larsen

The phase diagram of the Ta-Zr system is presented with a discussion of the methods used in its determination. The solidus contains a minimum at 1820°C near 25 wt pet Ta. A complete solid solution exists at elevated temperatures between tantalum and ß zirconium. This solid solution decomposes monotectoidally at 800°C and 12 wt pet Ta. The maximum solubility of tantalum in a zirconium is slightly less than 2 wt pet, and decreases with decreasing temperature. The solubility of zirconium in tantalum is 5 wt pet at the monotectoid temperature and about 2 wt pet at room temperature. THIS investigation was part of a program of research on refractory metal alloy systems having potential application in nuclear reactor technology. Preliminary prop-ess has been reported in the Ames Laboratory annual research reports.l Most of the previously reported work on the Ta-Zr alloy system consisted of partial phase diagram investigations and the determination of the mechanical properties of the zirconium-rich alloys. Anderson eta1.2 studied alloys containing up to 30 wt pet Ta as part of an investigation of several zirconium alloy systems. These investigators also determined some of the mechanical properties of the alloys at room temperature and 650°C. In a discussion of Anderson's work, Pfei13 suggested that the bright phase in the microstructures of the intermediate alloys is a tantalum-rich solid solution or an intermediate phase in a matrix of ß zirconium solid solution. Litton,4 Keeler,5 and Chubb6 determined the mechanical properties of zirconium-rich alloys at ambient and elevated temperatures. Van Thyne and McPherson7 reported the tensile properties

Jan 1, 1962

By CHRIS A. HARTNAGEL

For the second consecutive year, the production of crude petroleum in New York has fallen below the 5,000,000-bbl. Mark that had prevailed previously since 1937. In 1945, the output totaled 4,658,000 bbl., a decrease of slightly more, than one per cent from the 1944 production. This total represents 2 per cent of the stripper-well production of the United States, which in turn is I 3 per cent of the total annual yield of the nation's petroleum.

Jan 1, 1946

By J. PARK

Discussion of the paper of J. PARSE CHANNING, presented at the New York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 529 to 538. FRED H. RINDGE, JR., * New York, N. Y.-It is interesting to note that although this movement was started only seven years ago at Yale, it has spread in that brief time to 200 colleges and technical schools, anti thousands of men are interested in it. There are 3,000 graduates who became acquainted with the movement in college days anti are now promoting the industrial betterment idea all over the country. Some of these men are employed entirely in this work, and the number of such workers is constantly increasing. We feel we are really doing a very fundamental thing in getting so many coming engineers and prospective employers of labor to interest themselves in these things which we have been discussing this morning; these things which are so vital to efficiency and success in any line of business or engineering to-clay. Of course the institutions located in our large industrial centers have the greatest opportunity for practical service. But I have just returned from one college, Pennsylvania State College, where 300 engineering students in three clays signed up as interested in this movement and as anxious to take active part in the work this summer. That is one of a number of colleges situated in towns where there are 110 industrial opportunities. Therefore, their field of service must be where they work

Jan 5, 1915

By Joseph A. Holmes

Iv all new movements unavoidable misapprehensions arise, which should be cleared away, lest they retard the progress of the movement itself. An impression has gone abroad that the movement for conservation of resources is a new movement. No one knows better than the engineer that this is not the case. Men like Douglas and Raymond and John Fritz and Edison and McDonald, and hosts of others, have preached and practiced conservation as applied to mineral resources throughout a long and useful life-time; and, in general, the work of the engineer and the chemist, both in this and in other countries, has been along the line of continually greater efficiency in the use of all available materials. And the results already accomplished through the efforts of these experts are now saving annually many millions of dollars to the people of the United States in materials and labor. It is true, however, that the need for conservation, that is, for a wiser and more efficient use of the natural resources, has taken on a new life, and is being brought home to the people of the United States in a manner which is awakening public interest and even the public conscience. It is, therefore, both appropriate and fortunate that the engineers, the chemists, and the thinking men of all classes are availing themselves of the present impetus to the movement to emphasize anew the lessons which heretofore they have found it more difficult to impress upon the American public or even upon the captains of industry. Still another of these misapprehensions is to the effect that many of the leaders in the present movement hope to bring about conservation of resources through legislation or execu-

May 1, 1909

By R.K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

By R. K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

The paragraphs quoted, regarding Mr. Hoover's appointment as chairman of the newly organized food board of the United States, are taken from the editorial page, of the New York Times for April 13: ?The country is fortunate in commanding the services of Herbert C. Hoover as Chairman of the newly established Food Board. This is n, problem of first importance. Few realize the extent to which American food stuffs will enter into the decision of the war, and it is doubtful if it has occurred to many minds as yet that we shall have to deny ourselves what we have regarded as necessaries in order to keep our European allies supplied. " Mr. Hoover is one of the leading mining engineers of the country. At the outbreak of the war he put his private affairs aside to become the head of the American Commission for Relief in Belgium. He has had an experience that perhaps no other man has ever had, covering the raising of money and the purchase and distribution of supplies on a large scale; He has been brought into close relations with the neutrals and the belligerents on both sides. By them all he is recognized is one of the best executives brought to the fore by the mar. Mr. Hoover is in a position now to place abilities and experience at the service of his country. He will come back with comparative data that will enable him to measure resources and deficiencies accurately. This appointment gives renewed assurance of our Government's grasp of the problems of war and its resolve to apply, business principles to their solution."

Jan 5, 1917

By C. E. Tsoutrelis

A new method for determining rock drillability in diamond drilling is discussed; the method takes into consideration both penetration rate and bit wear. The method is based on drilling a rock specimen under controlled laboratory conditions using a model bit. The technique used for determining the experimental variables is extremely simple, quick, and reliable. Drillability is then determined by the mathematics of drilling. In considering the different factors that affect diamond drilling performance, the nature of the rock to be drilled is of outmost importance since it affects significantly the drilling costs and such other variables as bit type and design, drilling thrust, and bit rotary speed. Many attempts have been made to study this effect by correlating actual drilling performances either to certain physical properties of the rock being drilled1-? or to test drilling data obtained under laboratory conditions.7-13 These attempts were aimed at providing a reliable method of predicting by simple means the expected rock behavior in actual drilling, thus giving the engineer a tool to use in estimating drilling performances and costs in different types of rock. The purpose of this paper is to describe such a method by which rock drillability (a term used in the technical literature to describe rock behavior in drilling) could be determined in diamond drilling. It is believed that the proposed simple and reliable method will cover the need of the mining industry for a workable method of measuring the drillability of rocks. It should be emphasized, however, that since drill-ability depends on the physical properties of rock and each drilling process (diamond, percussive, rotary) is affected by different or partly different rock properties,14-l6 the proposed method of determining rock drillability cannot be extended to the other drilling processes. The results presented in this paper form part of an extensive three-year research program carried out by the author in the laboratories of the Greek Institute of Geology and Subsurface Research. During this period the effects of the physical properties of rocks and of such operational variables as drilling thrust and bit rotary speed in diamond drilling were investigated in detail. DRILLABILITY CONCEPT The literature is not devoid of drillability studies. While there are a number of investigators1,3,5-7,9-0,12-13,17 who have attempted to establish by direct methods (i.e., drilling tests under laboratory conditions) or indirect (i.e., through a physical property of rock) an index from which the drilling performance in a given rock may be estimated, very few6-7,9,12, of the proposed methods seem to be of much practical value to the diamond drilling engineer and none to date has been universally accepted. Commenting on the proposed methods for assessing rock drillability, Fish14 remarks that "for a measure of drillability to be accepted it is essential that penetration rate at a given thrust and bit life are elucidated as otherwise the method is of little value." This statement should be examined in more detail by making use of the penetration rate-drilling time diagram obtained in drilling a rock under constant operational conditions. Furthermore, the merits of using this diagram to describe rock drillability will be pointed out. At the same time reference will be made to this diagram when discussing some previously proposed methods. Fig. 1 illustrates such a diagram for three rocks,A, B, and C, which have been diamond drilled under identical conditions. It is assumed here that rocks A and B have the same initial penetration rate, i.e., VOA = Vog, but since rock B is more abrasive than A, rapid bit wear occurs and as a result the fall of its penetration rate with respect to time is more vigorous than in rock A. This is shown graphically by a steeper V = f(t) (0 curve in this rock than in rock A. Rock C has a lower initial penetration rate, due to higher strength properties16 but since it is not very abrasive, only a slight fall of its penetration rate occurs during drilling (in this category are some limestone and marbles with compressive strength above 1000 kg per sq cm). It follows from the foregoing considerations that the characteristic for each rock curve (I) is a function of (i), the penetration rate of the rock Vo recorded at the instant of commencing drilling, which determines the starting point of the curve (1) on the y-axis and (ii), the abrasive rock properties which determine the rate of fall of Vo with respect to time. Thus, curve (I) provides an actual picture of the rock behavior in drilling for given operational conditions, and it can be used with complete satisfaction to assess rock drillability. It can be seen clearly from Fig. I that proposed methods for assessing rock drillability by measuring the

Jan 1, 1970

By Robert H. Richards, Richard W. Lodge

A great deal of speculation, as well as actual experiment, has been devoted to ascertaining the changes in the materials (luring their descent in an iron blast-furnace, affecting (1) the chemical constitution, (2) the mechanical condition, and (3) the arrangement of the materials. With a view to throw some light upon the third question, we constructed a model and tried experiments which are here described. Our model is a vertical section of a furnace, with the lines of the Edgar Thomson furnace D of 1885 for the use of which we arc indebted to Mr. Gayley. The model is 40 inches high, and made to scale (1/2 inch equals 1 foot), and the horizontal section of the space through which the charge falls at any point in the descent is 11/2 in. x d, d being the diameter of the furnace at that place. We are unable to say just where the idea of making this model came from ; perhaps, partly from The Principles of the Manufacture of Iron, and Steel, 1884, I. Lowthian Bell, p. 124 ; partly, also, from

Jan 1, 1888

By B. N. Das, J. B. Darby, P. A. Beck, Y. Shimomura

A POWDER pattern for the (Cr, Mo, Co)R-phase annealed at 1200°C was reported in 1951.1 Through the courtesy of Prof. D. P. Shoemaker of Massachusetts Institute of Technology the authors became aware of inconsistencies of this pattern with that to be expected from the structure of the R-phase, as determined by Komura, Shoemaker, and Shoemaker.' In addition, Professor Shoemaker also noted that the powder pattern reported8 for the (Cr, Mo, Co)D-phase, annealed at 1300°C, agreed fairly well with that to be expected from the newly determined structure of the R-phase. In view of these findings, the previously reported powder patterns of the R-phase and of the D-phase were compared carefully. It was found that most lines in the two patterns (22 lines) were to a fair degree of accuracy related to each other by a single conversion ratio for the corresponding d spacings. The value of the conversion ratio was found to be 1.0058, so that the d spacings of the D-phase pattern previously reported were larger than the correspond- ing d spacings for the reported R-phase pattern by approximately that factor. The intensity relationships between corresponding lines in the two patterns were similar, as judged visually. The following exceptions were noted: Lines Nos. 2, 3, 19, 20, 21, 22, 23, 24 and 25 of the D-phase pattern,:' all designated weak or very weak, were missing in the apparently somewhat fainter R-phase pattern used.' Lines 1, 2, 3, 5, 15 and 34 (all weak or very weak), reported for the R-phase, were missing in the D-phase pattern, Table I. In view of these observations it seemed probable that the two patterns differed from each other mainly by a slight change in lattice parameters (with c/a remaining approximately constant), and that the pattern previously reported for the R-phase contained some weak extraneous lines, most likely to be attributed to impurities. In order to check the foregoing assumption, two specimens of an alloy containing 43 pct by weight of cobalt, 41 pct molybdenum, and 16 pct chromium, which was within the composition range of stability of both the D-phase at 1300°C and of the R-phase at 1200°C, were homogenized at 1200 and 1300°C, respectively, and quenched. X-ray diffraction patterns of the powders of these two specimens, obtained with CrK radiation, were compared carefully with each other and with the D-phase pattern previously

Jan 1, 1959

By Goodman, Richard E.

A complete rational analysis for design of excavation slopes and loaded rock masses is a desirable but perhaps unattainable goal. Irregular external and internal boundary conditions, poor understanding of failure criteria for large masses of rock, capricious material properties, and the importance of indeterminate forces and inaccessible and virtually un- sampleable rock defects emphasize the importance of experience in this aspect of rock engineering. The experience must be correlated with geological factors. In certain regions the accumulation of such experience through the observation of existing rock slopes in various formations constitutes an important aspect of studies for design of rock excavations.

Jan 1, 1969