Search Documents

By J. Walter Snavely

PRESENT-DAY processing in many industries, calcining, sintering, briquetting, beneficiation and nodulizing, increasingly calls for the handling of large volumes of hot bulk materials. Various types of conveyors have been employed. This discussion will cover the factors governing their selection. For temperature ranges up to 400°F, or approximately 200 °C, a wide range of conveyors is available. Special constructions of rubber conveyor belts, steel conveyor belts, vibrating and shaker conveyors, apron conveyors, and drag chain conveyors, all are used successfully. As temperatures go well above 400 2F, however, choice of conveyors is narrowly limited. This paper will consider the problem of handling bulk materials only where the temperatures exceed 400°F. The arbitrary selection of 400 °F as a dividing point undoubtedly can be challenged, as special conveyor belting constructions are available which are suitable for temperatures in excess of 400°F. However, when the relatively short life of such belts and the cost of their replacement, with the attendant down time, are balanced against the reliability and long service life of the properly designed steel constructed units to be discussed, there is little question in any operator's mind that the special belts are more expensive to use. Because the conveyors under study are for the handling of bulk materials, inevitably including a high proportion of fines, obviously wire mesh belts cannot be included for consideration. Even though this type of conveyor is widely used at high temperatures, i.e., for carrying glassware through a lehr, it is unsuited for the conveying of bulk materials, and therefore will be excluded from further discussion in this paper. Preliminary to the study of the conveyor itself is the determination as to whether the material is to be cooled while it is being handled, or whether the processing requires retention of all heat and the maintenance of a given temperature range. In the majority of cases cooling is incidental to or part of the handling process, when the handling, for example, follows completion of sintering, roasting, calcining, refining, or some other process. To meet such operating conditions successfully, the conveying medium used must have: 1—a construction capable of withstanding maximum initial temperatures of the material being handled. 2—a construction providing efficient heat transfer for cooling. 3—a construction providing dependable operation and long life with minimum service requirements, and 4—a construction providing controlled and efficient conveying. Under the usual conditions of cooling during the handling, the construction selected to withstand the initial maximum temperatures does not necessarily involve using alloys, as excellent results can be achieved with normal carbon steels and cast irons, when they are properly applied and proportioned. The earliest and simplest type of conveyor for handling very hot materials is the cast steel drag chain conveyor, still widely used for handling hot cement clinker, as illustrated by Figs. I and 2. Because of the rugged and generous proportions of the chain link design, low carbon steels are entirely suitable for the links. The pins, however, must be alloy steel. The simple, rugged construction of this type of conveyor makes it readily capable of withstanding high initial temperatures, even though the chain is operating buried in the material. The drag-chain type of conveyor has advantages and limitations. Although the efficiency of the heat transfer is relatively poor, the life of the conveyor is reasonably long, and because of its crude simplicity it does not require much servicing. However, as a conveyor, it is limited in capacity, and largely limited to horizontal runs. Furthermore, because of the crude design, heavy weight, and the chain operating at the temperature of the material, greatly reducing permissible operating chain pulls, this type of conveyor is limited to relatively short centers. Another type of conveyor that has been used for very hot materials is the cast pan conveyor. Because of its very generous proportions the cast pan, which is made of either cast iron or malleable iron, can withstand initial maximum temperatures. It also provides efficient heat transfer for cooling. Further, it is on efficient conveyor construction, which can be used for inclines. Because the chain employs rolling friction instead of sliding friction, and is not in the maximum temperature zone, much longer centers are possible. It is this type of conveyor that is frequently used in the casting of various metal pigs, pig iron, and aluminum; it is obvious, therefore, that very high initial temperatures are being handled. With this kind of conveyor the return run is frequently sprayed with water to accelerate heat transfer. The build-up of residual heat in the very heavy cast pans is thus overcome. The outboard roller steel pan conveyor is an improved pan conveyor' which provides high rates of heat transfer and substitutes formed steel pans for the heavy cast pans. It is a very efficient conveying medium. The details of this particular construction are clearly shown in Fig. 3. An early application of this type of conveyor is shown in Fig. 4. In this case the conveyor units are handling roasted phosphate rock at average temperatures of 1000" to 1500°F, and frequent maximum temperatures as high as 1900°F. Several widths are used. The capacity of the unit at a speed of 50 fpm is approximately 30 tph per inch of width at peak loadings, average capacity being about 1/3 of peak loading. The assembled conveyor is shown in Fig. 5, with views of both the top and the underside to show all the construction details. In particular, the following general design principles were carried out in this construction:

Jan 1, 1954

By R. C. Allen

About four years ago the writer proposed a revision of the correlation of the Huronian formations in Michigan, and noted the bearing of the question on the correlations of the Huronian rocks in Wisconsin and Minnesota.1 Dr. C. K. Leith opposed this revision and argued for the retention of the correlations of the United States Geological Survey, published in 1911,2 for which he and Dr. Van Hise were mainly responsible. As late as June, 1917, Harder and Johnson, following Leith, thought it "premature to change radically a correlation based on years of careful field work."3 The work of Wolff on the Mesabi and Cuyuna Ranges, of Hotchkiss on the Gogebic Range (unpublished), and of the writer and assistants on the Michigan ranges, together with data developed by exploratory and mining operations, has introduced so many new facts not recognized in the scheme of the U. S. Geological Survey that the correlations of 1911 must be considered, in some important respects, obsolete. Indeed, new data are accumulating so rapidly that any classification, which for the moment may seem best to explain the facts, is almost immediately modified or refined by further observations. The problem of Huronian correlations is difficult, but interesting and important. With the aid of fossils, stratigraphers of the post-Algonkian formations have been able to show that slight disconformities mag separate strata of vastly different ages, and that within physically conformable strata may be concealed a hiatus of great magnitude. In the non-fossiliferous Huronian group, minor physical breaks in the strata are only beginning to attract attention, and it is too early to discuss what bearing these will have in correlating the formations of one area with those of another, but it is safe to say that the "lost intervals" which are not disclosed by physical relationships will remain forever lost; therefore we may not hope to discover the ultimate truth concerning the

Jan 1, 1920

By E. H. Wells, A. Andreas

Greater progress than in any previous year was accomplished by the oil industry in New Mexico in 1936. The total number of completions in the state was 631, of which 549 were oil wells, 21 were hydrocarbon gas wells, three were carbon dioxide gas wells, and 58 were dry holes. The total oil production for the year was 26,804,446 bbl. Compared with the production for 1935 of 20,228,947 bbl., this represented a gain of 32.5 per cent. Of the total production, 25,337,382 bbl. came from Lea County. The average daily nonmarginal well allowable for that county was 115 bbl. the first of the year and 86 bbl. at the close. Production was regulated by the New Mexico Oil Conservation Commission,

Jan 1, 1937

The following is an incomplete list of members and guests who called at Institute headquarters during the period Dec. 10, 1918 to Jan. 10, 1919. P. G. Bandy, Mexico City. Wm. B. McKinley, Yonkers, N. Y. Bennett R. Bates, Berkeley, Cal. Captain C. E. McQuigg, Conn. William T. Bates, Mascot, Tenn. Lt. H. G. Mathews, Cal. Lt. Don C. Billick, Alturas, Cal. Lt. M. S. Mazany, Mich. L. E. Booth, Watertown, Mass. Ralph A. Meyer, Hill City, S. D. J. T. Boyd, Denver, Colo. C. F. Moore, Boston, Mass. J. R. Buchanan, Pasadena, Cal. H. W. Nichols, Chicago, Ill. Ensign G. M. Burke. R. B. Olsen, Mays Landing, N. J. Captain E. H. Clausen. M. L. O'Neale, Gouverneur, N. Y. F. L. Cole, Manila; P. I. F. W. Osborn, New York, N. Y. Joules Cousin. Lt. Fred S. Porter, Alaska. A. Faison Dixon, Washington, D. C. G. M. Richards, Palmerton, Pa. James T. Dixon, London, England. T. C. Roberts, E. Orange, N. J. Everett Drennen, Elkins, W. Va. W. E. Ruder, Schenectady, N. Y. F. Eichelberger, Helena, Mont. Ensign W. A. RuKeyser, Boston. R. B. Eldredge, Colorado Springs, Colo. A. H. Sawyer, Boston, Mass W. F. Ferrier, Ottawa. Lt. D. F. Schindler, New York. Martin Fishback, Benson, Ariz. L. G. Sparks, Greenshurg, Kan. T. E. Fisher, Dover, N. J. W. H. Staver, New York N. Y. D. C. Gilbert, Ft. Wayne, Ind. Douglas B. Sterrett, St. Cyr, Canada. Lt. Lauriston B. Herr, Cuba. Warren D. Thompson. G. S. Holmquist, Washington, D. C. Enrique Touceda, Albany, N. Y. Lt. E. Ross Housholder, Ohio. Mathew van Siclen. Hugh C. Ingle, Santa Rosa, Cal. Flying Cadet Christian Vrang, Cal. Lt. M. W. Kishman, Ariz. L. G. Weeks, Bisbee, Ariz. Hugo E. Koch, Watertown, Mass. C. E. Wheelock, Mogollon, N. M. H. M. LaFollette, LaFollette, Tenn. Major A. E. White, Washington, D. C. Clinton R. Lewis, Dawson, Y. T. Lt. J. L. White, Humboldt, Ariz. The Secretary of the Institute has received with sincere appreciation a Christmas card extending the season's greetings from the officers' mess of the 3d Tunnelling Company, Canadian Engineers, B. E. F., France, and takes this means of reciprocating to these officers and men of the company the best wishes of the members of the Board of Directors. Charles E. Addams has removed from Ray, Ariz., to Phoenix, Ariz., where he is chairman and director of the Arizona State Council of Defense.

Jan 2, 1919

By A. J. Lyon

THE stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening; which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging-heating in a temperature range below 170° C. (340° F.)-will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1928

By Robert W. Hunt

(Cleveland meeting, October, 1912.) PERHAPS of all the scientific economic questions which have been claiming the attention of capitalists, metallurgists, manu-facturers, directors of public utilities, and the general public of America, during the last few years, none have been of more importance than the one relating to the wear and safety of steel rails. The discovery of the Bessemer process made possible modern railway development. In that growth, as has generally happened in all progressive movements, ill its department have not remained equally balanced. Iron rails permitted the construction of roadways for the passage of power-driven vehicles. In time the speed and weight of such carriages proved too much for the wearing-qualities of the rails, and the limit of railway capacity seemed to have been reached. Bessemer made his invention, which was soon perfected and developed, especially as related to steel rails, and thereby increased the limit of capacity, acid vastly greater railway progress was, made possible. The Siemens-Martin open-hearth process followed, and was later supplemented by the Thomas-Gilchrist basic improvement. For a time the Bessemer steel rails of commerce Were, more than equal to all that was asked of them, but this did not long continue, as evidenced by the records in our Transactions. Revolutionary changes occurred in the industrial world, and in no part of it more than in steel-rail manufacture. Great and powerful commercial combinations were made, whose financial resources made possible the supplanting of the then most efficient blast-furnaces, steel-works, mid mills, by others of theretofore unimagined capacity. Old traditions and practices of steel-making were wiped away, and, in too many cases, output was apparently the chief aim, with the result that much dissatisfaction with the wear and safety of rails was felt by railway officials, and the general public was concerned as to its safety when traveling. The climatic conditions of the winter

Dec 1, 1912

By P. Martinez, A. F. Hoyte, F. E. Senftle

The possibility of applying a neutron activation technique for silver exploration is considered. A mobile positive-ion accelerator type neutron source is used to irradiate a small area of rock or soil in situ. By using a short period of irradiation and gamma ray spectral analysis, a technique is shown for silver exploration. Two different mobile units are described. Laboratory and preliminary field tests both indicate that a sensitivity of less than 1 oz of silver per ton of ore can be achieved. The increasing consumption of silver for industrial uses and also for coinage has caused a serious shortage of silver in this country. The silver shortage has been reviewed and analyzed by kiilsgaard1 who concludes that, "The best hope for meeting future demands for silver is through accelerated exploration for precious ores." As almost all the exposed "bonanza" type silver deposits evidently have been found, it is urgent that some sensitive geophysical technique be found to detect large, extended, but generally low-grade, secondary ores, as well as hidden vein deposits. Silver is easily made radioactive by exposure to slow neutrons; hence a neutron activation method appears promising for locating silver deposits. The principles of mineral beneficiation using neutron activation techniques were discussed some years ago.2-4 Using the same approach, a preliminary description5 has been published of neutron activation as a mineral exploration tool. An exploration technique is described in which silver is made radioactive in situ and detected with a gamma radiation counter. The technique is similar to the well-known method used for uranium exploration. THEORETICAL CONSIDERATIONS Elemental silver consists of two isotopes, Ag107 and Ag109, having naturally occurring isotopic abundances of 51.4% and 48.6%, respectively. For short periods of irradiation of silver by thermal neutrons, the long-lived 250 day, half-life isotope, Ag110m, is not produced in significant quantities. However, significant quantities of 2.3 min half-life Ag108 and 24.5 sec half-life Agl10 are formed by the following reactions. Ag108 and Agl10 emit a 0.44 Mev (million electron volts) and a 0.66 Mev gamma ray, respectively. Ag107 + n + Ag108 (2.3 min) Ag109 + n + Ag110 (24.5 sec). Because of the large capture cross section (110 barns) of Ag109, and short half-life of Ag110 (24.5 sec), the 0.66-Mev gamma ray is the most prominent emission from silver for neutron activation periods of about a minute's duration.* The 0.44-Mev gamma ray from Ag108 will also be present, but will be one or two orders of magnitude lower in intensity. The decay scheme of Ag110 is shown in Fig. 1. If the neutron irradiation time is limited to about 100 sec, the Ag110 activity will essentially reach saturation and can be used to detect the presence of silver. In a neutron flux of 10 8 neutrons/cm2/set, the induced 0.66-Mev activity in 1 g of silver will be about 2 x 107 disintegrations per sec. This is about 1000 times the measurable gamma activity of 1 g of uranium in equilibrium with all its decay products; hence there is ample activity for detection. Under the same conditions of activation, most of the other elements do not reach this relatively high disintegration rate. Although this is in favor of the proposed technique, other problems must be considered. For mobile operation, it is desirable to obtain the largest neutron flux to weight ratio. Hence we have used a small 150-kev accelerator-type neutron source rather than an isotopic source such as an americium-beryllium neutron source. By use of remote control system, an accelerator-type neutron source can be safely used without the massive shield required for an isotopic source. Moreover, an accelerator-type source is more versatile in that it allows one to use a flux of either 14-Mev or 3-Mev neutrons, depending on whether a tritium or a deuterium target is used. With a 14-Mev generator, one can obtain a flux of 10 9 neutrons/cm 2/sec, and with a 3-Mev generator, the flux is generally two orders of magnitude less. Although silver will become activated with either generator using proper moderation, detection may be

Jan 1, 1968

By Woolsey McA. Johnson

In metallurgical circles it is known widely, but somewhat vaguely, that the ease of reduction of metallic oxides depends largely on the way they hare been prepared. It is likewise known that different forms of carbon have different and greatly varying reducing powers. It is the purpose of this paper to show somewhat more definitely and scientifically these facts. Some years ago the writer published an account of pyrometric determinations of the reduction temperature of zinc oxides variously prepared and of several kinds.' In said paper it was shown that the temperature at which zinc oxide evolves zinc according to the equa-tion ZnO + C = Zn + CO depends upon the nature of the two reacting bodies. The determina-tions had a range of accuracy of from 2° to 6°C., whereas differences were found to amount to an extreme of 90' C. So the differences are real ones and must have a definite cause. The equation of boiling water, (H2O)4 D 4 (H2O) has a fixed temperature for equilibrium of 100° C. at 760 mm. pressure. In general, all equations reacting in the liquid or the gaseous phase have well-defined constant physical conditions which govern the equilibrium point and reaction velocities. In a reaction where we have one or more solid phases, the tempera ture conditions requisite for the unbalancing of the stable system are found to vary. These variations are due to the fact that in a solid there is a very complex molecule and it is not a question solely of the tearing away of two interlocked atoms, but also of the destruction of a complex molecule containing hundreds, or possibly thousands, of smaller molecules. In other words, there are two forces to be overcome: a certain

Jan 1, 1914

By Henry M. Howe

This paper is a discussion of the extremely valuable one of Mathewson and Phillips, The Recrystallization of Cold-Worked Alpha Brass on Annealing,1 which not only gives us a wealth of important data reached with great intelligence, but also shows both uncommon powers of imagination and a perfectly fair spirit. Let me try to analyze some of their results, and to enunciate some of the laws to which these results point. For brevity I refer to them as "The Authors." The page numbers in parentheses refer to their paper. 1. The Visible Aspects of Recrystallization.—Plastic deformation in a single direction, as in cold-rolling, draws the grains out in that direction, that is, inequiaxes them, without destroying their apparent individuality. Each grain seems to endure the drawing out without changing either its volume or its orientation materially, for the etching tint of each grain seems to be as uniform after as before the drawing out, save for the "etch bands,"2 shown in Figs. A to D of the Authors' Plate I. As the drawn-out metal is heated progressively, on reaching a certain "disintegration temperature" these old grains seem to break up, probably into submicroscopic fragments, and this apparent disintegration is followed by a coalescence of these fragments, so that their number decreases and their size increases, till they may become very much coarser than before the drawing out. Ruder3 coarsened the grains of silicon steel in this way till single grains reached an area of 50 cm. (7.75 sq. in.). The deformation itself probably breaks each grain up into many very small fragments, but the fact that each grain continues to have a uniform etching tint different from that of its neighbors indicates that these fragments retain the initial common orientation of the grain. The apparent disintegration which we observe, then, is rather an abandonment of community of orientation for individuality of orientation, by the fragments formed earlier during the deformation. Hence we

Jan 1, 1917

By B. Ladanyi, B. Hoyaux

A first requirement for assessing the safety of a rock slope, either artificial or natural, particularly if the rock behaves in an elastic-brittle manner, is a propw knowledge of the distribution of stresses within the slope and their development with time and advancement of workings. There are a uumber of different methods that can be used, in principle, for obtaining this information, such as (1) stress measurement in situ, (2) photoelasticity,1 (3) analytical methods, and (4) numerical methods. In cases where the stress distribution cannot be obtained by classical analytical methods, as in the one considered herein, either photoelasticity or numerical methods are norrnally used. However, actually, due to the rapid development of high-speed computers, increasing preference is given to the numerical methods. Among the latter, the most successful ones, to date, for determining the stress distribution in slopes have been (1) the finite difference method,2-4 (2) the lumped parameter method,5 and (3) the finite element rnethod.6 However, for determining gravity stresses in a natural rock slope, only the finite difference method has been used until now.7,8 A solution of the same problem by the finite element method will be shown here in which a particular reference is given to the development of tensile fracture zones within the slope. FINITE ELEMENT METHOD The stress analysis using the finite element method originates from an extension of the matrix analysis of structures.9 It consists in decomposing a continuous medium, assumed herein to be homogeneous and isotropic,

Jan 1, 1972

By W. H. Forbes

As permissible explosives and electric detonators are now generally recognized as the only safe means of blasting in coal mines, this paper is limited to their use. Causes of Misfires There are many different causes of misfires, but the principal ones are as follows: 1. Explosives which have deteriorated through improper storage either at the storage magazine, the distributing magazine, or at the working face. This is not only true of the explosive itself, but also of its detonating agent. 2. Improper priming and charging at the working face. This commonly occurs when the explosives are handled by inexperienced persons. 3. Improper methods of tamping; the leg wires of the detonator may be abraded or broken by the tamping bar or stick, thereby causing a short or broken circuit. 4. Faulty leading wire, or electrical apparatus of insufficient strength to explode the detonator. Prevention of Misfires Storage is an important factor, especially with permissibles of a nitrate or ammonia base. Both explosives and detonators should be stored in substantially built, fire-resisting magazines and should be situated so that the minimum amount of moisture and heat is present. They should be so constructed that a constant supply of fresh air enters; the floor of the magazine should be raised to permit the circulation of air under the stored explosives. Boxes should be stored top side up and in such a manner that the old explosives are used before those of a later delivery. This eliminates chance of deterioration from lengthy storage. Detonators should be similarly handled and stored. The distributing magazine stock should be regulated so that not more than one day's supply is on hand.

Jan 1, 1930

By L. W. Blau

RESEARCH work in exploration and production was further reduced during 1943 owing, partly, to difficulties in the acquisition of apparatus and, principally, to the exodus of research men to governmental agencies conducting research and to the armed forces.

Jan 1, 1944

By John D. Kalasky

The success in providing adequate ventilation to the active faces of a coal mine for all methods of mining depends upon good face control and the air distribution and control system. A good system provides overcasts, air locks, regulators and bleeders so that an adequate flow of air will be confined to the working places with least opportunity for interruption, and that a flow of air is maintained, however small, across the worked out area to the bleeder and away from men and equipment at all times. In gaseous mines, it is just as important to satisfy effective bleeding as it is to satisfy the air volume requirements in the operating splits. The two requirements go hand in hand. Although not complicated, ventilation and methane drainage in longwall mining in a gaseous mine require careful forethought and adequate facilities to make them safe.

Jan 8, 1966

By Henry M. Howe, W. P. Barba

When this country went into the war, but two concerns, The Bethlehem Steel Co. and The Midvale Steel and Ordnance Co., knew how to make steel fit for great cannons and at these concerns there were relatively few men who knew the whole art. Fortunately, certain of these men put their knowledge at the service of the Government, and proceeded to instruct the metallurgists at the arsenals and at various steel works. Doctor Howe, then chairman of the Engineering Division of the National Research Council, suggested that this work might be facilitated, and the number of effective gun-steel makers thereby increased, if a detailed description of the best practice could be written, giving the reasons for the various steps, and issued with the endorsement of a committee composed of those who were evidently the most competent authorities. It was thought that something would be gained by clarification of the subject, and something by the eminent authority of the members of the committee. To that end, the Engineering Division appointed a committee, consisting of the gentlemen whose names follow, to mention on1y those who retained their connection with it. At this time there were serious difficulties in the manufacture, for the Government. of aircraft and high-speed engine crankshafts, of certain ordnance forgings, and of shells for both the Army and Navy. This Committee was asked to study and report upon these, with a view to betterment of practice. There were indications that the source of some of the difficulties went back to the melting of the steel and the production of the ingot. Hence, the committee first studied steel melting and ingot production, in order to guide the wartime manufacturers to an even larger percentage of useful production from the steel initially melted. Committee on Steel Ingots W. P. Barba, chairman, Ordnance Dept., U. S. A. (formerly Vice Pres. & Gen. Mgr., Midvale Steel Co., Philadelphia). George K. Burgess, Chief of Division of Metallurgy, U. S. Bureau of Standards, Washington, D. C. Henry M. Howe, Then Chairman Engineering Division, National Research Council.

Jan 1, 1922

By W. P. Barba, Henry M. Howe

When this country went into the war, but two concerns, The Bethlehem Steel Co. and The Midvale Steel and Ordnance Co., knew how to make steel fit for great cannons and at these concerns there were relatively few men who knew the whole art. Fortunately, certain of these men put their knowledge at the service of the Government, and proceeded to instruct the metallurgists at the arsenals and at various steel works. Doctor Howe, then chairman of the Engineering Division of the National Research Council, suggested that this work might be facilitated, and the number of effective gun-steel makers thereby increased, if a detailed description of the best practice could be written, giving the reasons for the various steps, and issued with the endorsement of a committee composed of those who were evidently the most competent authorities. It was thought that something would be gained by clarification of the subject, and something by the eminent authority of the members of the committee. To that end, the Engineering Division appointed a committee, consisting of the gentlemen whose names follow, to mention on1y those who retained their connection with it. At this time there were serious difficulties in the manufacture, for the Government. of aircraft and high-speed engine crankshafts, of certain ordnance forgings, and of shells for both the Army and Navy. This Committee was asked to study and report upon these, with a view to betterment of practice. There were indications that the source of some of the difficulties went back to the melting of the steel and the production of the ingot. Hence, the committee first studied steel melting and ingot production, in order to guide the wartime manufacturers to an even larger percentage of useful production from the steel initially melted. Committee on Steel Ingots W. P. Barba, chairman, Ordnance Dept., U. S. A. (formerly Vice Pres. & Gen. Mgr., Midvale Steel Co., Philadelphia). George K. Burgess, Chief of Division of Metallurgy, U. S. Bureau of Standards, Washington, D. C. Henry M. Howe, Then Chairman Engineering Division, National Research Council.

Jan 1, 1922

By HORACE H. EJIRICH

(New York Meeting, February, 1912.) PREFATORY NOTE.-The first part of this paper was sent to me by Mr. Emrich nearly nine months ago ; and. I held it, waiting for the second part, which he had promised to forward soon, so that I might submit the whole to some of his former professional associates, and advise him of their criticisms and suggestions before offering his work to the Institute. But, five days before the second part reached me, I received by telegraph the news of Mr. Emrich's sudden death. The paper has therefore not had the benefit of such a revision by the author as might have made it in some respects clearer and more complete. Nevertheless, I believe that experts in the branch of metallurgy with which it deals will find it both original and suggestive.-A. EILERS. I. PARTIAL REFINING IN THE ANODE-FURNACE. During my connection with one of the large New Jersey copper-refineries, and probably before that period, from 15 to 20 per cent. of the copper-bullion received was the very foul, leady blister-copper produced from lead blast-furnace matte. It had been customary to mix a small part of this blister with each charge of purer pig-copper, in the effort to dilute it as much as possible before casting into anodes; but tank-house conditions were such that I was led to try making entire furnace-charges of this blister, and refining it as much as possible in the furnace-afterwards casting to anodes and refining electrolytically, in tanks and solution separate from the main bulk of the purer copper. In making this experiment, notes were made, for several furnace-charges, of everything thought to have a bearing on the question, and some interesting facts were brought out, both in the furnace-working and afterwards in the tanks.

Jun 1, 1912

By D. S. Greig

There was a decline in the Italian oil production in 1933 and also in the footage drilled. A total of about 194,500 bbl. of crude oil was produced in the Emilia district of northern Italy from the same fields in production as in 1932. New drilling to the extent of 80,700 ft. failed to find new production to compensate for the decline in old wells, and no new fields were discovered in spite of an active exploration campaign by the government-owned company A.G.I.P., which has just completed the first year of a five-year exploration program. This company drilled a total of about 33,000 ft. The majority of its tests were drilled in the Po Valley upon locations selected by geophysical methods. This company is changing over to the rotary system for all future wells. It produced about 16,600 bbl. of oil from wells near Salsomaggiore and in the Po Valley. The Petroli d'Italia, which operates the old fields of Montechino, Valleja and Gratera south of Piacenza, has been doing normal development drilling in the endeavor to extend its present fields. Also it was drilling two exploration wells in the Torino district. It drilled a total of about 13,930 ft. and produced approximately 12,645 bbl. of very high-grade oil (specific gravity about 0.765). The Societa Petrolifera Italiana was occupied chiefly in exploratory drilling in the endeavor to extend its producing fields at Salsomaggiore and at Vallezza, south of Parma. It was also drilling one exploration well at Rile dell7Olio near Voghera on the line Milan-Genoa. It drilled a total of 33,849 ft. and obtained a production from its two fields of 165,273 bbl. It also produced 123,220 gal. of casinghead gasoline from Vallezza field absorption plant.

Jan 1, 1934

By H Pray, H. W. Russell, Paul D. MILLER

It is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranu-lar corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels has been ably discussed by Bain and co-workers1-3 and by other investigator4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measuremerits, measurement of the degree of cracking produced on bending over a malldrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A.-1011 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. Experimental Method A small area of the steel under test is subjected to an anodic treatment in a cell that can be 'lamped Onto a a Or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring Or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8- diameter' The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941

By H. W. Russell, H Pray, Paul D. MILLER

It is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranu-lar corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels has been ably discussed by Bain and co-workers1-3 and by other investigator4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measuremerits, measurement of the degree of cracking produced on bending over a malldrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A.-1011 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. Experimental Method A small area of the steel under test is subjected to an anodic treatment in a cell that can be 'lamped Onto a a Or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring Or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8- diameter' The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941

By Hans W. Schreiber, David W. Neuhaus

INTRODUCTION The Sunshine Mining Company's 16-to-1 silver deposit and mine project are located 384 kilometers (240 miles) southeast of Reno and 360 kilometers (225 miles northwest of Las Vegas, near Silver Peak in Esmeralda County, Nevada, at an elevation of about 2,300 meters (7,000 feet). The deposit was being developed, in 1980, with an anticipated mining and milling rate of 150,000 tons per year (500 tons per day). Mining is by underground, blast-hole open stoping with rubber-tire haul-age out of the mine to a straight cyanide plant about 5.5 kilometers (3.5 miles) from the mine. The product is a gold-silver dore which may be further refined at Sunshine's new refinery in Kellogg, Idaho. The cash required for investment was obtained through the sale of $25 million worth of 6 l/2h silver-indexed bonds. Some $15.0 million were directed toward development of the 16-to-1 Mine. These bonds, which were underwritten by Drexel Burnham Lambert of Chicago in April of 1980, are redeemable on or after April 15, 1985 or payable at maturity on April 15, 1995 at the greater of either $1,000 or the market price of 50 ounces of silver. Behre Dolbear acknowledges the kindness of the Sunshine Mining Company (Sunshine) for allowing the presentation of the subject material for this Case Study. APPLICABILITY AS CASE STUDY Reasons for Choosing 16-to-1 The reasons for choosing the 16-to-1 Mine as a case study follow: 1. The project is simple and compact. 2. The mine is small -- thus relevant to other contemplated precious metal operaions in the western states. 3. The areas of risk are readily identifiable. 4. A change to project financing was under consideration. 5. A substantial decline in the price of silver was experienced during development. 6. Behre Dolbear undertook one of the first feasibility studies of The 16-to-1 and thus has some familiarity with the project. Historical Summary The following history serves as a setting: 1. Late 1920s -- minor "production"(?) via shallow pitting. 2. Mid-1930s -- neighboring Nivlok Mine successfully put into production. 3. Late 1950s (?) -- Callahan Mining Company acquired rights and drilled -- results inconclusive; Callahan turned property back to Arthur Baker, who had originally interested Callahan in 16-to-1 on the basis of its similarity with Nivlok Mine.

Jan 1, 1985