Search Documents

By W. H. Bassett

A 10-year, sea-water, corrosion test of tubes of several copper alloys has shown that many alloys withstood attack by solution, pitting, and dezinkification; a 1-year, salt-spray test of sheet-metal specimens of the same composition showed the same results. THE late J. P. Sparrow, chief operating engineer of the New York Edison Co., carried out a series of practical tests on condenser tubes of several copper alloys and reported on the results to the Association of Edison Illuminating Companies at its meeting in' September, 1913. In the preparation of these tubes the senior author had the pleasure of cooperating. Copper-zinc alloys in the proportions of 60-40, 70-30, 80-20, 90-10, and Admiralty metal, which is in effect 70-30 with 1 per cent. of tin, were tried. Monel metal and several copper-nickel alloys, and 8, 5, and 3 per cent. aluminum bronze were also tried. At the time of this report, the aluminum bronze had been in service for 4 1/2 years and seemed to be giving especially good results but later it began to fail and showed no substantial improvement over Admiralty metal. Monel metal was unsatisfactory and the nickel alloys apparently did not give better service than the Admiralty alloy. Previous to the publication of the report, and after considerable discussion, it was agreed that a test where tubes of different kinds could be under laboratory observation would be advisable, so the apparatus described here was set up in The American Brass Co.'s Waterbury Laboratory. This was fitted with tubes of copper, brass, bronze, nickel silver, cupro-nickel and other alloys, and the test started Oct. 11, 1912. Salt water from East River, New York harbor, was barrelled and transported to the laboratory for the test. A fresh supply, completely replacing the water in service, was obtained at the end of each six months period.

Jan 1, 1925

By H. E. Cline, D. F. Stein

A fine lamellar structure with interlamellar spacings ranging from 0.I to 3.7 was Woduced by high-speed directional solidification and used to study the interaction of dislocations with an array of bimetallic bound-am.es. The tensile flow properties were measured at elevated temperatures and the results interpreted in terms of an image force model. As the width of the plates decreases the strength increases according to a Hall-Petch relation, suggesting pile -ups. Considerable strengthening was also observed at elevated temperatures. In recent years composites containing a strong but brittle phase and a ductile but weak phase have been studied extensively in the search for a high-strength material with adequate ductility.' However, the strength of these composites has been limited to a volumetric average of the strengths of the component phases. In this paper we will show that a composite made by directional solidification of a Cu-Ag eutectic has strength properties that substantially exceed the strength of either of the metals in the composite, and an explanation for this increased strength will be presented. The Cu-Ag eutectic is a near ideal material to study for several reasons. The eutectic structure is made up of alternate plates of silver-rich and copper-rich phases with the same crystal structure.2'3 In addition, the mechanical and elastic properties of silver4 and copper5 are known over a wide range of temperatures and the eutectic microstructure is stable to nearly the melting point.6'7 Therefore, the properties of the eu-tectic are readily comparable to various theories involving the mechanical properties of copper and silver. The experiments consisted of producing directionally solidified Ag-Cu eutectic material, determining the structure and performing tensile tests at different temperatures and strain rates. EXPERIMENTAL A) Solidification and structure. A cylindrical ingot 2.2 cm in diam and 15 cm long was prepared from 99.999 pct pure materials and cast in argon. The ingot was placed in an alumina crucible and was direc-tionally solidified at 7 x 10"4 cm per sec in a Bridg-man apparatus in argon. Metallographic examination at both ends and along the length of the ingot showed a uniform structure that consisted of fine alternate plates of silver- and copper-rich phases. The plates were aligned parallel to the growth direction, as shown in the longitudinal section, Fig. 1, and were in small randomly oriented domains of parallel plates as viewed in a transverse section, Fig. 2. Four smaller ingots 0.175 in. in diam were solidified at speeds of 2Xlo-', 4.4 xlo-', 4.4 x 10-3, and4.4x10-4 cm per sec to produce a range of lamellar spacings. Replica electron micrographs were taken to resolve the individual plates as shown in Fig. 3. The copper-and silver-rich plates in the larger ingot were about

Jan 1, 1970

By Johann F. Kerl

Autogenous batch grinding tests were performed in laboratory-scale tumbling mills with magnetite, limestone, and sandstone pebbles. The influence of pebble size, feed size, mill speed and loading, and grinding time on the fineness of grinding was investigated. Comparisons were made with the results from ball mill grinding experiments.

Jan 1, 1972

By ROBERT. RICHARDS

I. INTRODUCTION The object of this paper is to enlarge the field of settling velocities treated by me in my former papers, Close Sizing Before Jigging, and Sorting Before Sizing.' There seemed need of work both on coarser and on finer sizes. Messrs. A. Sidney Warren and M. L. Nagel undertook the investigation for the coarser sizes, from 12.85 mm. down to 2.05 mm. diameter. Their work, because of the closer spacing and because of the increased number of observations and consequent stronger averages, called for a revision of the former work. Messrs. G., A. Barnaby and Ralph Hayden undertook this part of the work, from 2.49 mm. down to 0.28 mm., which is near the limit of sifting. Their work covers the ground much more minutely and comprehensively than the former papers. There remained to be covered the portion of the field too fine for investigation with the sieves. This part, covering the range of grains from 0.48 to 0.03 mm., was undertaken by Mr. E. S. Bardwell. For it he used the elutriation method. II. THE FIRST, OR COARSEST, SECTION OF THE FIELD. The first desideratum in this investigation was a series of sieves for sizing the sands preparatory to making the tests. It became necessary, therefore, to decide on a sieve-scale for this purpose. A sieve-scale is a series of sieves in which the dimensions of the holes of the successive members form a series increasing by a. definite ratio. There are three natural sieve-scales : 1, progressing by doubling the width of the hole for each suc-

May 1, 1907

By R. H. Richards

The spitzlutte, as described by Rittinger, is an instrument by which saud is sorted in a continual upward-flowing stream of water. Its usual firm is that of a pointed box, placed with the point downward, the box receiving. its feed of sand and water on one side and discharging its tailings on the other. The sorted product or concentration is discharged at the bottom, at the apex of the box, through which it falls against an upward current of water, which current serves to effect the sorting and separation. To make this exposure to the quicksand condition still more effective, an inverted dam is placed across the spitzlutte, which forces the sand in its passage from the feed side to the discharge to pass clown into the more active portion of the upward-flowing current of water. In the form adopted for small tests in the mining laboratory of the Massachusetts Institute of Technology (see accompaaying sketch) the feed is'throogh a central funnel instead of being at the side, and the apex of this funnel, extending down nearly to the apex of the cone, talks the place of the inverted dam in the large spitzlutte. To keep the experiment perfectly under control a bulb or bottle is attached by a rubber connecting-tube to receive the concentrations, and between this bottle and the apex of the spitzlutte is placed a glass tube of conical form, with a side tube for' the admission of water. By regulating the admission of water through this tube the concentration may be allowed to go down into the bulb as fast or as slowly as the richness of the ore seem.; to demand. This spitzlutte may be used on products that have been previously sized to take out the heavy mineral. As an example of this a test was made upon a sample of ore where the galena, blende, and quartz were much mixed up, but separated fairly when crushed. The sample of ore was from Newburyport, and assayed 16.61) per cent. lead.. After sizing through a series of sieves the ore yielded conceutrations and tailings to the spitzlutte as follows :

Jan 1, 1881

By Arnt Solbu, Jomar Thonstad

The reaction between CO, and aluminum in cryolite-alumina melts in contact with aluminum has been studied by passing CO2 over the melt. In unstirred melts a homogeneous reaction between dissolved metal and dissolved CO2 was observed. In stirred melts in which convection was induced by bubbling argon through the melt, the dissolved metal apparently reacted mainly with gaseous CO2. The rate of formation of CO increased slightly with increasing depth of the melt, and it did not depend on whether CO2 was passed over or bubbled through the melt. The rate of formation of CO increased with increasing area of the metal/melt interface and with the application of anodic current to the metal. It is concluded that the dissolution of metal into the melt is the rate-determining reaction. THE current efficiency in aluminum electrolysis is determined by the rate of the recombination reaction between the anode gas and the metal: 2A1 + 3CO2—A12O3 + 3CO [1] as originally stated by Pearson and waddington.1 The occurrence of this reaction in cryolite-alumina melts in contact with aluminum was first verified experimentally by Schadinger.2 Thonstad3 has shown that the reaction may proceed further to give free carbon: 2A1 + 3CO— A12O3 + 3C [2] Normally only a few percent of the CO formed undergoes such reduction. The mechanism of these reactions has not yet been clarified. Aluminum, as well as CO,, is soluble in the melt. The solubility of aluminum in cryolite-alumina melts at around 1000°C corresponds to 75 x 10- 6 mole A1 per cu cm,4 while that of CO2 is only 3 x 10-6 mole CO, per cu cm.5 Taking into account the stoichiometry of Reaction [I], the ratio between dissolved aluminum and dissolved CO2 available for the reaction in a saturated melt is about 40. Therefore, as will be shown in the following, the reaction probably mainly occurs between gaseous COa and dissolved aluminum. The dissolved aluminum presumably consists of subvalent ions of aluminum and sodium.4'6 Since the interpretation of the present results is not dependent upon the nature of this solution, the dissolved metal will be designated solely as Al+ in the following. The reaction can then be divided into four steps: A) dissolution of metal, e.g., 2A1 + Al3 — 3A1+ [3] B) diffusion of dissolved metal through a boundary layer; C) transport of dissolved metal through the bulk of the melt; D) Reaction [1]. If dissolved CO, takes part in the reaction, three additional steps embodying the dissolution and transport of CO2 must be added. schadinger2 observed, when bubbling CO2 through the melt, that the rate of formation of CO (in the following designated rfco) did not depend on the distance from the metal surface. The results also indicate that the rate of bubbling did not affect the rfco. When passing CO, over the melt, Revazyan7 found that the loss of metal did not depend on the depth of the melt above the metal or on the flow rate of CO2, and concluded that Step A is rate-determining. In an unstirred melt, however, Gjerstad and welch8 found that the rfCo decreased with increasing depth of the melt, indicating that step C was rate-determining. It thus appears that the rate control of the process depends on the experimental conditions, particularly on the convection. In the present measurements the reaction has been studied in unstirred as well as in stirred melts. EXPERIMENTAL AND RESULTS The experiments were carried out at 1000°C in a Kanthal furnace with a 10-cm uniform temperature zone (±0.l°C). The melts were made up of "super purity" aluminum (99.998 pct), hand-picked natural cryolite, and reagent-grade alumina. In experiments where alumina crucibles were used, the alumina content in the melt was close to saturation (13.5 wt pct9); otherwise it was 4 wt pct. Pure Co2 (99.85 pct) was passed over the melt, and the exit gas was analyzed for CO2 and CO by the conventional absorption method.3 From the weighed amount of CO (as CO2) the rfco was calculated as the number of moles of CO formed per min per sq cm of the surface area of the melt. The amount of carbon formed by Reaction [2] was not determined. As already indicated the rfco is much higher than the rfC, by Reaction [2]. Since the rfC probably is proportional to the rfco, the measured rfco should then the proportional to, but slightly lower than, the total rate of Reactions [I] and 121. In general the scatter of results obtained in duplicate measurements was ±5 to 10 pct, while within a given run a precision of ±3 to 5 pct was obtained. The various crucible assemblies that were used will be described below. Measurements in Unstirred Melts. When carrying out aluminum electrolysis in small alumina crucibles. Tuset10 observed that after solidification the lower part of the electrolyte was gray and contained free metal, while the upper part near the anode was white and contained no metal. One may test for the presence of free metal by treating with dilute hydrochlorid acid.

Jan 1, 1969

By Jei Y. Choi, Paul G. Shewmon

The surface self-diffusion coefficient of copper (D,) has been measured between 847° and 1069 "C for six different orientations. These were the(111), (110, (100, and three higher index surfaces. The activation energy for Ds (designated Q s) was found to be about 49 kcal per mol for all six surfaces, and Do about 2 x 104 sq cm per sec. At any temperature Ds varied by no more than a factor of three over these orientations. It is shown that, if the free energy of a surface atom is uniquely determined by its number of nearest neighbors, it follows from the Principle of microscopic reversibility that Qs should have the same value for all surface orientations, and Ds should vary little with orientation. This model also suggests that for clean fee metals Qs ~ 2/3 AH, (heat of vaporization). This is true for copper. ALTHOUGH it has been appreciated for several decades that atoms can diffuse more rapidly on a surface than through the bulk of a crystal, it has only been in the last few years that reliable values of the surface self-diffusion coefficient (Ds) have become available. Tracer studies of Ds had been attempted prior to this period, but when a tracer is placed on a surface, an ever increasing fraction of it is drained off into the lattice. The correction for this loss involves a very difficult, and as yet unperformed calculation. Those who have worked with tracers have not corrected for this loss.1, 2 Thus their results indicate that Ds is greater than the self-diffusion coefficient in the lattice (Dl), but it has not been established that they give quantitative data on Ds. A procedure which avoids the problem of tracer loss is to study the rate of mass-transfer under the effect of surface tension. If the surface asperity being studied is very small, the mass transfer occurs entirely by surface diffusion. The kinetics at which a grain boundary groove forms on an initially plane surface is a well-studied case of this type. The smoothing of a slight scratch in an otherwise flat surface is another procedure that has been studied. If these grooves are up to 20 to 30 µ in width, the dominant mechanism for mass transfer is surface diffusion (at least in the case of metals with low vapor pressures), and the widths can easily be measured with an interference microscope. Of these two, mass-transfer techniques only in the case of grain boundary grooving has a rigorous mathematical treatment been given. This was done by Mullins.3,4 His analysis predicted that in the case of copper in an atmosphere of an inert gas, surface diffusion should be the dominant transport mechanism. This analysis gave an equation for the groove profile and predicted that the width of the groove would increase as (time)1/4. Mullins and Shewmon showed that both of these predictions agreed with experiments.5 Thus the validity of the values of Ds given by this procedure seems to be well established. Gjostein has used copper bicrystals and the grain boundary grooving technique to determine Ds and the activation energy for surface selfdiffusion (9,) in the [001] direction on surfaces ranging between the (100) and (110) planes.= He reported that Qs = 41 kcal per mole and Do = 6.5 x 102 sq cm per sec for all orientations studied. Since the results did not change with the dew-point of the dry hydrogen atmosphere or the type of refractory tube used, he concluded that the surfaces were clean, or at least that the results were not influenced by any impurities chemisorbed from the atmosphere. The work reported here reproduces and extends Gjostein's study in that D s and Q s were determined for copper over a wider range of orientations. To study the effects of impurities, two purities of copper were used as well as cathodic etching to remove any possible electropolishing film. Gjostein postulated that the diffusing atoms on a surface near a low index plane are the few atoms which are adsorbed on the smooth region between ledges or steps in the surface. A more rigorous derivation of the equation relating Ds to the concentration and jump frequency of these adsorbed atoms is given here. Using this treatment, our empirical observation that Q s and D s are essentially the same for all surface orientations can be shown to follow from the assumption that the free energy of a surface atom is uniquely determined by its number of nearest neighbors. The studies of D s using the scratch technique have been carried out by Blakely and Mukura on nickel,' and by Geguzin and Oveharenko on copper. The latter study using copper gives values of D s roughly

Jan 1, 1962

By William H. Pettee

A few weeks ago the Institute lost, by death, from its list of members one who in recent years, by frequent attendance at meetings, by the preparation of papers, and in many other ways, had shown a warm interest in Institute affairs; who had an extensive acquaintance among his fellow-members, and whose memory it is fitting to perpetuate by a permanent record in the volumes of our Transactions. Dr. Byron William Cheever, acting Professor of Metallurgy in the University of Michigan, died at his home in Ann Arbor, on the 6th of March, 1888. He was born September 17th, 1841, in Ellisburg, Jefferson County, New York. In 1844, the family moved to Geneva, Illinois, and thence, in 1857, to Dundee, Michigan. Two years later, a third removal was made to Ann Arbor to take advantage of the educational facilities there offered; and in 1859 the subject of this sketch, with his two brothers, entered the University of Michigan. In 1863, he took the degree of Bachelor of Arts. After a year or two of business life, he entered the medical department of the University, and graduated as Doctor of Medicine in 1867. A taste for scientific work had been developed in him in early life; and, even while carrying on undergraduate and medical studies, his proficiency in chemistry found recognition in his occasional employment as assistant in the University laboratory. The interval between the close of his course in Arts and the commencement of his course in Medicine was also devoted to chemical work, partly in the city of Philadelphia, and partly in the West Indies, where he was employed in the service of a commercial company engaged in the guano trade. Dr. Cheever never took up regular practice as a physician. After receiving his medical diploma he went again to Philadelphia, and for about two years was employed as an analytical and consulting chemist in that city. A favorable opportunity occurring for work in the Rocky Mountain mining region, he left Philadelphia and

Jan 1, 1888

By J. J. Beeson

For the past fifty years or more, the structural features of the Cordil-leran mountain system of western United States have presented some most interesting problems. Any geologist or engineer living in this region, or even making occasional examinations of the mines, will lose much of interest and importance if he is not familiar with the literature. Some of the greatest works on geology have been the result of studies carried on in sections of this region. Among the more important of the earlier works are those of Dutton,l King,2 Gilbert3 and Powell;4 of the more recent Lindgren,5 Ransome,6 Spurr,7 Butler8 and others have contributed much. Many of the papers are largely of scientific interest but even these lay the foundation for the commercial application of the broader features of the geology. I have read many of these works with the keenest interest and pleasure; in fact, some have been read until some of the more important findings seem to be my own. In this paper, however, it is my aim to accept credit for little more than the labor of assembling some of the ideas of others. This is done with the hope that an interesting and valuable discussion will be the result. If some of the ideas presented should

Jan 1, 1927

By G. Ansel, J. P. Doan

THE important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holub1-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength, and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British. Patent 5111376 relates to the parent discoveries of Sauerwald, Eisen¬reich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature" has been found to the particular characteristics of wrought Mg-Zn-Zr alloys, with which the present paper is concerned. - The work to be discussed represents essentially an extrusion study of the Mg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metal¬lography, and toughness of these alloys. Compositional variations are limited to the ranges o to 7 per cent Zn and o to I per cent Zr. EXPERIMENTAL PROCEDURE Alloying and Casting Alloying ingredients were cell mag¬nesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl2 and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manu¬facturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zir¬conium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux¬inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1946

[Aalde, Kaare, ('40) New Mexico School of Mines, Socorro, N. M. Abadesco, Enrique A., ('39) Univ. of the Philippines, Manila, P. I. Abdul-Ahad, A., ('39) Montana School of Mines, Residence Hall, Butte, Mont. Abreu, Ovidio M., ('38) Univ. of Nevada, Reno, Nev. Acker, Voscoe, . ('39) Agricultural & Mech. College of Texas, College Station, Tex. Acosta S., Gonzalo, ('40) Univ. of Texas, Univ. Sta., Box 1785, Austin, Tex. Adams, Albert, ('38) New Mexico School of Mines, Socorro, N. M. Adams, Charles W.,' ('39) Michigan College of Min. & Tech., Houghton, Mich. Adams, Hugh T., Jr., ('39) Univ. of Oklahoma, Norman, Okla. Adams, Jack L., ('39) Univ. of Oklahoma, Norman Okla.]

Jan 1, 1940

By J. S. Owens, R. W. Marsden, J. W. Emanuelson, R. F. Werner, N. E. Walker

The iron ores of the Mesabi Range occur in a 340 to 750-foot thick, Precambrian cherty iron formation termed "taconite." For about 65 years, extensive natural iron ore bodies were mined, and the ores either shipped as a direct ore or processed by gravity methods to a shipping grade iron ore. Since 1956, magnetite taconite ores, occurring in magnetite-rich horizons in the Biwabik iron formation, have been commercially concentrated and agglomerated. The transition from natural ores to concentrating-grade ores is progressing rapidly so that, in the near future, a major percentage of the iron ore shipped from the Mesabi Range will be as iron ore pellets produced from taconite. Natural iron ores of the Mesabi Range occur in the Biwabik formation as trough ore bodies in elongated channels and as irregular and tabular deposits in fractured areas associated with faults and folds. Ore bodies range in size from a few thousand tons to hundreds of millions of tons and may occur in any part of the iron formation. In some areas of strong ore development, ore was formed from the hanging-wall argillite to the footwall quartzite. The natural ores and beneficiating-grade natural crude ores were formed by the oxidation of the iron minerals, magnetite, greenalite, stilpnomelane, minnesotaite, and siderite, to hematite and goethite and by the removal of much of the silica in the cherty quartz and in the associated silicates by leaching. The ores are believed to have formed by the oxidizing and leaching action of surface waters. Magnetite taconite ores occur as stratigraphic zones in the Biwabik formation where it contains sufficient magnetite to be concentrated profitably, by magnetic methods, to give a magnetite concentrate that is agglomerated into a high quality product. Unoxidized taconite has an extensive distribution away from and between channels of oxidation and leaching but only a part of the unoxidized taconite is of ore grade. Two general types of magnetite taconite ore occur: ( 1) magnetite taconite of the Main Mesabi Range, generally west of Mesaba, which is composed of magnetite associated with cherty quartz, greenalite, stilpnomelane, minnesotaite, and carbonates and (2) magnetite taconite of the Eastern Mesabi, generally east of Mesaba, composed of magnetite associated with quartz, cummingtonite, actinolite, ferrohypersthene, hedenbergite, fayalite, hornblende, pyroxene, garnet, and biotite. The Mesabi taconite is a metasediment derived from an iron- and silica-rich chemical sediment that has been regionally metamorphosed and, on the eastern end, additionally metamorphosed by the Duluth Gabbro Complex.

Jan 1, 1968

By Laurence Pellier

Electron microscopical studies were made of the effect of sensitization at 1200oF on a Type-.104 stainless steel with high carbon and low nitrogen and oxygen contents, after solution annealing and after cold working. The loci of the carbide precipitates in the early stages of sensitization were followed in dry stripped plastic replicas. Some observations were made by direct electron transmission on thinned films. Intragranular dislocations showed a high degree of stability through the annealing necessary to produce sensitization. I HE present work was undertaken to determine the effect of sensitization, at 1200°F, for 1/2 hr, on the electron microstructure of a Type-304 stainless steel with high carbon, and low nitrogen and oxygen contents, after solution annealing and after cold working. Many electron microscopical studies of sensitization of 18-8 stainless steels have already been made. Most of them utilized extraction replicas, from which the morphology and composition of the precipitated carbides could be established.'-" ry stripped replicas were seldom used for such studies, although it was demonstrated that they are applicable, in general, to EurveYs of the general microstructure of many alloys' and, in particular, to the observation of precipitated carbides in austenitic stainless steels.3

Jan 1, 1963

By Frank H. Macpherson

When it became apparent early in 1941 that the United States might be drawn into the war, studies were made of the bauxite situation in Arkansas, principally because 9.5 pct of the known bauxite reserves of the country were located in that State. Bauxite mining was then geared for maximum production to supply ore to meet this country's war requirements and, if necessary, to supply the needs of Canada as well. In view of the comparatively small bauxite reserves, Congress appropriated funds for an extensive exploratory drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. An alumina plant was erected near Bauxite and an aluminum plant near Hot Springs, Ark., by the Defence Plant Corp. The Metals Reserve Co. established a schedule of prices, arranged for stockpile sites and a buying agency. Operators cooperated to step up production and new ones came into the field. Production Record Prior to 1941, the greatest annual production in Arkansas was 562,892 long tons, dry basis in 1918. During the single month of August 1943, 693,596 long tons were mined—130,704 tons more than for the entire year of 1918. In general the Arkansas bauxite deposits are relatively small, irregular in thickness, somewhat scattered and, compared to coal, iron or open-pit copper deposits, are ill-adapted to an expansion in output. Commercial deposits range in horizontal extent from less than an acre to about 40 acres and are usually very irregular in outline. The average thickness of all known workable deposits is between 12 and 15 ft. with a maximum of about 60 ft. The ore bodies are usually somewhat undulating and nearly horizontal although locally some deposits dip as much as IS°. Types of Bauxite Three physical types of bauxite may be recognized: pisolitic, granitic and amorphous. Pisolitic ore is the most common type. It consists of small pebble-like nodules, ranging from the size of a pin head up to several inches in diameter, all set in a fine grained matrix. Transported bauxite is usually- pisolitic. Most residual bauxite is granitic. It is believed not to have moved appreciably from the location where it originally was formed. This is indicated by the fact that it appears to grade into unaltered nephelite syenite, which it overlies. Amorphous ore is the least abundant. It is nonpisolitic and resembles clay, has no characteristic texture, and can be identified definitely only by chemical analysis. Uses of Bauxite Bauxite is chiefly used for, and at the present time is substantially the only

Jan 1, 1948

By Frank H. Macpherson

When it became apparent early in 1941 that the United States might be drawn into the war, studies were made of the bauxite situation in Arkansas, principally because 9.5 pct of the known bauxite reserves of the country were located in that State. Bauxite mining was then geared for maximum production to supply ore to meet this country's war requirements and, if necessary, to supply the needs of Canada as well. In view of the comparatively small bauxite reserves, Congress appropriated funds for an extensive exploratory drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. An alumina plant was erected near Bauxite and an aluminum plant near Hot Springs, Ark., by the Defence Plant Corp. The Metals Reserve Co. established a schedule of prices, arranged for stockpile sites and a buying agency. Operators cooperated to step up production and new ones came into the field. Production Record Prior to 1941, the greatest annual production in Arkansas was 562,892 long tons, dry basis in 1918. During the single month of August 1943, 693,596 long tons were mined—130,704 tons more than for the entire year of 1918. In general the Arkansas bauxite deposits are relatively small, irregular in thickness, somewhat scattered and, compared to coal, iron or open-pit copper deposits, are ill-adapted to an expansion in output. Commercial deposits range in horizontal extent from less than an acre to about 40 acres and are usually very irregular in outline. The average thickness of all known workable deposits is between 12 and 15 ft. with a maximum of about 60 ft. The ore bodies are usually somewhat undulating and nearly horizontal although locally some deposits dip as much as IS°. Types of Bauxite Three physical types of bauxite may be recognized: pisolitic, granitic and amorphous. Pisolitic ore is the most common type. It consists of small pebble-like nodules, ranging from the size of a pin head up to several inches in diameter, all set in a fine grained matrix. Transported bauxite is usually- pisolitic. Most residual bauxite is granitic. It is believed not to have moved appreciably from the location where it originally was formed. This is indicated by the fact that it appears to grade into unaltered nephelite syenite, which it overlies. Amorphous ore is the least abundant. It is nonpisolitic and resembles clay, has no characteristic texture, and can be identified definitely only by chemical analysis. Uses of Bauxite Bauxite is chiefly used for, and at the present time is substantially the only

Jan 1, 1948

By O. U. Bradley

The extent of losses, due to evaporation, sediment, and water, in crude oil stored in steel tanks, is a very interesting question, and particularly so at this time, when every reasonable measure should be employed to eliminate all possible losses of this important natural product. Available information on this subject is incomplete; e.g., during the development of the Cushing Field, considerable surplus oil was stored in steel tanks, but from time to time, owing to changes in weather, some losses by evaporation and short storage room on the leases, these tanks were topped out, thus rendering inaccurate any system designed to determine the average rate of evaporation or other losses of the oil over a given period. Furthermore, the losses, as shown by the records at the time, as a result of hasty gages, failed to take into account the temperature and gravity of the oil. Losses may be classified roughly as occurring from evaporation, presence of sediment and water, and leakage. The coefficient of expansion and contraction of crude oil, in relation to temperature conditions, is of material importance; also, the rate of evaporation is dependent upon the gravity of the oil, as the escape of the lighter hydrocarbons in fresh Cushing oil, of from 40 to 42 gravity, on a warm day is considerable, and from available records of temporary storage, it is safe to assume that a loss of 1 to 11/2 per cent. in volume will easily occur in light crude oil of Cushing grade over a period of 6 months, including the summer season. The presence of sediment, water, and other impurities, in the oil will also cause more or less deterioration in quality, particularly when the fresh production is run direct from the gage tanks, or from the wells on the lease to steel storage, as is often the case when an oil field is being rapidly developed. The bad oil will settle to the bottom of the tanks and may be determined by thiefing and running a centrifuge test on the sample. The amount of water in the oil depends entirely on the conditions under which it is produced. Sometimes in large producing wells, with heavy gas pressure, some water may come in with the oil, particularly if the well has been drilled to the top of a water sand. Under these conditions, cut oil is often produced, which, if not settled out, is carried over into the steel tanks. The losses by leakage in steel tanks are difficult to determine, for

Jan 1, 1920

By Ernest Klepetko

A NOTABLE amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: [Specific gravity (melted) 1.03 -1. o6 Acid number6-8 Softening point, mercury method 160 -165°C Iodine value (Wijs)140-1.50 Refractive index1.544 Color (Hellige, 25 pct toluol) ...14 Molecular weight, average732 Purity, 99 + pct pure hydrocar Bon] "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility. The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration engineer for Combined Metals Reduction Co., obtained U. S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1947

By F. E. Harris

It has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-'. If the term used for carbon concentration is weight Pet C, as is customary, then a factor must be found, changing this term to One of weight Per unit volume when the diffusion coeficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expresses all evaluation of unsteady flow whereby D is given a relationship with the numerical value of C-x slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-x curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. KO such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. The Steady State Diffusion of Carbon in Au~tenite The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.' For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the Center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase: carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid ment down towards its steady state value. At points well removed from the ends, the concentration will remain the Same along planes parallel to the surfaces of the plate.

Jan 1, 1948

By F. E. Harris

It has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-'. If the term used for carbon concentration is weight Pet C, as is customary, then a factor must be found, changing this term to One of weight Per unit volume when the diffusion coeficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expresses all evaluation of unsteady flow whereby D is given a relationship with the numerical value of C-x slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-x curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. KO such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. The Steady State Diffusion of Carbon in Au~tenite The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.' For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the Center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase: carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid ment down towards its steady state value. At points well removed from the ends, the concentration will remain the Same along planes parallel to the surfaces of the plate.

Jan 1, 1948

By C. S. Samis, J. C. Mitchell

Sodion activity data have been obtained for the Na-A1 system for sodium concentrations in aluminum between NN, = 25 . 10-and 300 x 10'. This concentration intert-a2 encompasses those sodium concentrations nor1)zally encountered in aluminum reduction cell operation. The sodium activity data were measured by a two-phase equilibration of sodium between a lead and an aluminam rich phase. The Na-Pb system was emplojed as a reference for the determination of the actiz7itj 0.f sodium. The activity of sodiin in aluminuwz exhibits large positi2.e deviations frorn ideality and a strong dependence, on concentration below NN, = 100 x 1K6. The inteated data indicate that the activity of aluminium is equal to its mole fraction over the range of miscibility of the Na-A1 sgstem. The data on the Na-A1 binary have been combined with experimental data on the cryolite-A1 system at 1025°C to obtain the activities of Na F and AlF, in liquid cryolite oz2er the cornposition 1-ange encountered in aluminum cell operation. The results are in agreement with activities calculated from the NaF-AlF, phase diagram. ALUMINUM is produced commercially by the electrolytic reduction of aluminum oxide dissolved in molten cryolite. There is considerable controversy over the actual mechanism of the discharge processes, but sodium potentials in the systems appear to play an important role in the reduction mechanism. The metal-salt reaction involving NaF and aluminum to produce A1F3 and sodium is responsible for the presence of sodium in the aluminum metal phase. Additional sodium may be produced from the simultaneous deposition of sodium and aluminum at the cathode as a result of a cathodic overvoltage. runert' has suggested that sodium gas at atmospheric pressure would be the result of reaction between cryolite and aluminum at 1000°C. Subsequent investigations have shown that production of sodium at atmospheric pressure does not occur. These later investigations can be conveniently separated into two categories. The first involves sodium, aluminum, and cryolite, in which the sodium activity was measured. The second includes a lead phase for sodium activity measurement. Jander and errmann,' studied the reaction: at 1090°C in alumina crucibles under an atmosphere of dry, oxygen-free nitrogen. The equilibrium constant for the reaction was expressed in terms of concentration. Their results in Fig. 1 show an increase in sodium content of the aluminum with increasing NaF/A1F3 weight ratio. Pearson and waddington3 performed similar experiments at 1000°C. Their results are included in Fig. 1. Dewing and ollinshead have measured the sodium content of aluminum as a function of the NF/AF, ratio at 1025"C, Fig. 1, and ewin' measured the sodium content of the aluminum in a system involving the solid reactants NaF, cryolite, and liquid aluminum. This reaction is different from those discussed above. Two solid phases, NaF and Na3A1F6, and a liquid aluminum phase were present. The sodium concentration in the aluminum was determined by the temperature. Dewing's measurements covered the temperature range 679" to 896°C. Omo, Matsushima, and 1t02" investigated the equilibrium 6NaF ential thermal analysis. Stokes and Frank6 determined sodium activities by

Jan 1, 1970