Search Documents

By Donald F. Hammer, Donald W. Peterson

The Magma mine at Superior, Arizona, has produced over 13 million tons of ore yielding 1.5 billion pounds of copper. It is a mesathermal deposit, and, although the bulk of the ore has come from the Magma vein, most of the recent production has come from replacement deposits in limestone. The mine lies in a Precambrian and Paleozoic sequence of rocks that includes schist, diabase, quartzite, shale, and limestone; nearby, these rocks are intruded by igneous bodies of Mesozoic age that were probably the source of the ore-bearing fluids. Locally, these rocks are overlain by Cenozoic volcanic rocks and conglomerate. Layered rocks at the mine dip eastward about 30°. The area is extensively faulted, and surface faults are grouped into an earlier east-trending set and a later northtrending set. An additional set of diagonal faults that trends northwest and northeast is recognized underground. The east-trending Magma vein-fault, with its splits and branches, is the principal mineralized structure of the district. The bulk of the ore occurs in large ore shoots that plunge steeply westward and are sporadically connected by irregular ore shoots dipping gently eastward. The main ore controls apparently are selective zones of permeability related to the transverse faults. A bed of crystalline limestone near the base of the Martin Limestone (Devonian) is the host for the replacement ore bodies-discontinuous tabular pods dipping eastward parallel to the bedding. Selective permeability is again the apparent ore control, caused both by local hydrothermal solution of limestone and by deformation along faults. The principal copper minerals in the vein are chalcopyrite, bornite, enargite, tennantite, chalcocite, and digenite; these minerals vary in abundance according to a distinct zoning pattern. The upper part of the mine yielded considerable zinc as sphalerite, and the oxidized zone was rich in silver. The chief gangue minerals are pyrite, quartz, and hematite. In the limestone replacement bodies, chalcopyrite and bornite are the chief ore minerals.

Jan 1, 1968

By John T. Ryan

DEFINITE improvement in its accident fatality rate in the coal-mining industry was recorded during 1941, based on preliminary figures for the period from January through October. Total production during this ten-month period was approximately 91 percent of the total production in all of 1940. The ten-month accident rate for both bituminous and anthracite mining in 1941 was 2.15 killed per million tons of coal mined, compared with a rate of 2.66 for the full year of 1940. The bituminous rate decreased from 2.55 in 1940 to 1.99 in ten months of 1941, and the anthracite rate from 3.62 to 3.53 in similar periods. The decrease is more apparent for the bituminous branch of the industry, as the high figure in 1940 was due to seven major disasters which brought death to 276 men. The same number of major explosions during ten months of 1941 caused only 64 lives to be lost. The severity of the explosions has been lower this year but a definite need still exists for reduction in this type of accident.

Jan 1, 1942

By Carl Henrich

I have read with particular interest that portion of the discussion by Anton Eilers referring to the high-lime (and also high-alumina) slags made by August Raht in 1881, while smelting the Horn Silver ores at Franklin, Utah. The two analyses of such slags, furnished by Mr. Raht to Mr. Eilers are: (a) Not determined in this analysis. (b) Not given in Mr. Eilers' paper. Oxygen ratio, A1 as base. I. 0 in acid: O in base:: 18.1:18.9:: 0.96:1 11. 0 in acid :O in base:: 18.7:17.5::1.06:1 Average: 18.4:18.15=1.01:l Oxygen ratio, AI as acid. I. O in acid: O in base: :23.2:13.8:: 1.68:1 11. O in acid: O in base::23.1:13.5:: 1.76:1 Average: 23.15:13.4 = 1.73:l By assigning to alumina the the of a base, Mr. Eilers deduces the formula 3Feo.-2SiOa + 4Cao.2SiO². The nearest approach to a simple formula expressing the average composition of these slags, which I can figure, is 9RO.Al2O3.6SiO2. Allowing a ratio of 4Feo : 5Cao, we have for this formula:

Jan 1, 1917

By Frank C. Greene

Drilling in Missouri in 1943 continued at a lower rate than in 1942, only 28 wells being completed. Following the completion of the Cities Service Oil Company's No. I Jim Cook near Tarkio, in the northwest corner, NW. 'fi sec. 32, T. 65 N., R. 39, W., Atchison County, four dry holes were drilled by other parties, all a mile or more from the Cook well. Later the Cities Service Oil Co, completed No. 2 Cook for 60 bbl. Table I gives a summary of activities by counties. The total footage drilled was 23,83134 ft., of which 12,802 1/2 ft. was by cable tools and 11,029 by rotary. Four of the dry holes were drilled into Mississippian or older beds.

Jan 1, 1944

By Frank C. Greene

Drilling in Missouri in 1943 continued at a lower rate than in 1942, only 28 wells being completed. Following the completion of the Cities Service Oil Company's No. I Jim Cook near Tarkio, in the northwest corner, NW. 'fi sec. 32, T. 65 N., R. 39, W., Atchison County, four dry holes were drilled by other parties, all a mile or more from the Cook well. Later the Cities Service Oil Co, completed No. 2 Cook for 60 bbl. Table I gives a summary of activities by counties. The total footage drilled was 23,83134 ft., of which 12,802 1/2 ft. was by cable tools and 11,029 by rotary. Four of the dry holes were drilled into Mississippian or older beds.

Jan 1, 1944

By Norman B. Braly

The following is not offered as an extended paper on the subject of shaft sinking, but more as a description of the present practice of shaft sinking in the Butte district. The Anaconda company is sinking at present the following shafts: Badger State, Moose, Mountain Consolidated, Mountain View, Pennsylvania and Tropic. At the High Ore and Leonard mines the shafts are being deepened by sinking two compartments and will subsequently be enlarged to the full working size by raising alongside the compartments which are now being sunk. The following other companies are also sinking shafts: Butte-Alex Scott, Butte and Zenith City, Boston and Corbin, North Butte Mining Co. (at the Granite Mountain shaft), East Butte Co. (at the Pittsmont shaft), and the Rainbow Lode Development Co. Shaft Timbering. The shafts of the Butte district, generally speaking, are of three compartments arranged in a straight line, and the pump compartment is usually arranged for the use of an auxiliary hoisting cage, as well as for carrying pipe lines and electric wires. The Rainbow shaft is practically square, and of three compartments. The length of the shafts outside of timber will vary from 17 to 22 ft., and the width from 6 ft. 6 in. to 7 ft. Fir timber is used in all shaft work. This may be obtained from the Coast, when it is known as Coast fir, or from Idaho or Montana, when it is known as native fir. The native fir seems to be the tougher wood, but it is hard to obtain clear lumber in the lengths and sizes necessary for shaft work. Some of the shaft timber of the Anaconda company has been treated with creosote as a preservative, but this practice has not come into general use, as the ground of the camp is so heavy that the timbers usually crush before they rot. The size of timber most used for shaft work is 12 by 12 in., while 10 by 12 in., 10 by 14 in. and 12 by 14 in. are used for some of the special pieces around the shaft. The new Leonard shaft is timbered with 14 by 14 in. wall plates throughout.

Jan 1, 1914

By K. A. Jackson

An analysis of the conditiom fm the dendrite-eutec-tic transition is presented which takes into account a temperature gradient. The composition and temperature in the liquid ahead of a eutectic interface growing at a particular velocity are used to determine whether dendrites can grow faster than the eutectic interface in the liquid which exists ahead of it. If the dendrites grow faster, then a mixed structure with dendrites growing ahead of the eutectic interface is expected. If the dendrites do not grow faster, then only eutectic will be present. The analysis is presented for Sn-Pb system, for which sufficient experimental data to make the analysis are available. The transition from eutectic to dendrites-plus-eutectic derived by this analysis is in good agreement with the recent experimental observations of Mollard and Flemings on Sn-Pb alloys. In alloys which grow with a lamellar eutectic structure, the lamellar structure can be grown over some range of compositions close to the eutectic composition. When the composition is too far from the eutectic composition, dendrites of one or another of the primary phases grow ahead of the eutectic interface, producing a microstructure consisting of "primary phase" interspersed with a lamellar eutectic. Hunt and Jackson' have recently predicted the range of compositions over which the eutectic phase should grow in Sn-Pb alloys, and the composition-growth rate dependence of the transition from eutectic to dendrites-plus-eutectic. This prediction was based on work on organic eutectics. The model on which the prediction was based assumed that there was no temperature gradient in the system, a condition approximately satisfied in the study of organic eutectics2-5 but not in the growth of metallic alloys. Mollard and Flemings6,7 have recently reported experimental results for Sn-Pb alloys in which they have located the transition from eutectic to eutectic-plus-dendritic growth. The experiments were performed using large temperature gradients (65 to 515 deg per cm), so that the assumption of zero gradient on which the predictions of Hunt and Jackson' were based does not apply. It is not surprising therefore that the predictions' were not born out by the experiments.7 In the present work, a modification of the model used by Hunt and Jackson is presented which takes into account the temperature gradient. The modified form of the theory predicts the transition from eutectic to eutectic-plus-dendritic growth in terms of the composition, growth rate, and temperature gradient. Good agreement with the experimental data of Mollard and Flemings7 is obtained. THE HUNT-JACKSON MODEL The model used by Hunt and Jackson' to predict the transition from eutectic to eutectic-plus-dendritic growth was based on the assumption that dendrites grow ahead of a eutectic interface only if they grow faster than the eutectic interface. Analytic expressions for the growth rate of dendrites and the eutectic in Sn-Pb alloys were obtained by fitting experimental data with equations whose form was indicated by theory.

Jan 1, 1969

By G. Britsianes, T. L. Joseph

THE reduction of a lump of iron ore is a complicated sequence of up to three reactions proceeding simultaneously in a gas-solid system. As the ore moves down the blast furnace into zones of higher temperature and higher reducing power, it is successively reduced through the three oxides of iron into metallic iron. The reduction process involves much more than chemical problems. Physical factors add to the complexity of the overall process. Under optimum conditions, reduction of the ore is completed at a level about one-half way down the blast furnace stock column. At this point, the ore undergoing reduction has attained a temperature of about 1000°C and has been in the furnace for about 6 hr. On the practical side, the behavior of the ore during smelting has been of great interest to operators. Unsatisfactory blast furnace operation on burdens containing magnetite ore or badly slagged sinter has often been attributed to poor re-ducibility. The question of reducibility has also been raised in formulating quality standards for agglomerates such as nodules, briquettes, and pellets. In the present investigation, the solid phases formed during reduction were studied as a step toward a better understanding of the overall process. Equilibrium Studies The iron-oxygen equilibrium diagram shown in Fig. 1 reveal; a number of facts pertinent to the gaseous reduction of iron ores. This diagram is from the work of Darken and Gurryl, 2 and represents a correlation of the best available data. Four solid phases may exist during the complete reduction of hematite to metallic iron. These are hematite (Fe2O3), magnetite (Fe3O4), wustite (FeO), and iron (Fe). The wustite phase is a solid solution which is not stable below 570°C. At this temperature the solid solution undergoes a eutectoid-type of decomposition into the phases, magnetite and iron. Thus above 570°C, the diagram dictates that a hematitic ore should pass through a four-phase sequence on reduction to metallic iron. Below 570°C, only hematite, magnetite, and iron should appear. Information on the iron-oxygen system has been derived largely from CO and H2 reduction equilibria. The Fe-C-0 relationships have been studied extensively by R. Schenck and his coworkers and well summarized by H. Schenck.3 More recent studies have been made by Darken and Gurry.1, 2 Data from these sources have been combined and plotted in Fig. 2. With respect to the Fe-H-O system, the works of Emmett and Schultz4 seem the most reliable, and these data have also been included in Fig. 2. Certain physical properties of the solid phases of the iron-oxygen system are summarized in Table I. The crystallographic information is of special interest as much of the present work has been concerned with the X-ray analysis of the products of reduction. Reduction with Hydrogen The reduction of ore with hydrogen is the net result of two or more gas-solid reactions. Above 570°C, the reaction sequence may be represented by stoichiometric stages as follows: 3Fe203+ H2e2Fe,O, + H20 [1] 2Fe3O, + 2H2 6FeOw + 2H2O [2] 6FeOw + 6H3 ^ 6Fe + 6H=O [3] Fe2O3 + 3H2 ^ 2Fe + 3H,O. [4] These reduction reactions follow the general form: A (solid) + B (gas) e C (solid) + D (gas). This type of gas-solid reaction has been investigated by Langmuirl' who has shown that such reactions can occur only at the boundary between the two solid phases. Furthermore, a nucleus of the second phase must initiate the reaction. Once such an interface exists, the reaction proceeds through a layer of the solid reaction product (C). The specific mechanisms involved will depend a great deal on the properties and condition of this particular layer. A number of heterogeneous reactions such as the dehydration of single crystals of copper penta-hydrate and the calcination of limestone follow this type of process. It should be noted that the inter-facial type of reaction also occurs even in dense polycrystalline material which simulates a mono-crystalline behavior.

Jan 1, 1954

By Anthony Sharkey

Introduction In Europe, longwall mining accounts for over 95% of coal produced from deep mines, whereas in the U.S.A., longwall accounts for less than 5% of deep mine coal production. There are many reasons for the difference, but in general: a. U.S. mine operators have invested heavily in continuous mining or conventional equipment which continues to produce acceptable results; b. There 1s a reluctance to change from, a familiar (and proven) mining method to an unfamiliar one, despite promises of huge production increases,; c. Multi-seam mining in Europe has made longwall the only really viable mining method, whereas In the U.S.A. multi-seam mining (particularly in "below-drainage" mines), is relatively rare; d. Although some spectacular results have been achieved by longwall in the U.S.A.(I), the general performance of longwall in this country has not been good enough to generate much enthusiasm for its wide application; e. The much higher level of investment in face equipment required for longwall when compared to alternative methods (approximately $7.5 million for a medium seam longwall installation and $1 million to $1.5 million for a continuous miner section). However, declining productivity, national energy requirements and safety legislation are creating a situation in which longwall as a viable mining method is being examined more closely and in more places than hitherto. This paper, therefore, attempts to identify some of the principal criteria needing examination in any assessment of the feasibility of longwall application, the limitations of information for those criteria in the decision making process and the need for further research and development to assist the mine operators make the decisions.

Jan 1, 1981

By R. A. Spurling, C. G. Rhodes

SATISFACTORY metallographic sample preparation of very soft metals, such as lead and its alloys is generally difficult. The prime requisite of any technique must be that the result gives an undis-torted microstructure for the microscopist to examine. A small amount of mechanical polishing followed by a chemical or electrolytic polish is usually the most desirable way to obtain an undis-torted surface. Several chemical-4 and electrolytic3-' polishing solutions have been developed for dilute lead alloys. Perchloric acid mixtures (with acetic anhydride, ethyl alcohol, or water) are among the most prominent electropolishing solutions used for lead; however, the presence of bismuth in the alloy precludes the use of any perchloric-containing solution. The other solutions1-7 were found to be unsatisfactory on alloys ranging from 10 to 65 wt pct Bi in lead. With increasing bismuth content, the microstructure shows a lead (terminal solid solution), 0-6 mixture, E (peri-tectically formed hexagonal phase), and E bismuth mixture (eutectic at 56.7 wt pct Bi).9 The metallographic samples were mounted in "Araldite" epoxy (the heat generated during polymerization does not alter the microstructure), ground by hand on well-waxed silicon carbide papers (400 and 600 grit), and polished with 3- and 0.25-CL diamond paste on billiard and microcloths, respectively. The use of the various polishing and etching solutions reported in the literature resulted in the formation of irremovable reaction products on the sample surface when applied to "as-ground" or "as-polished" surfaces. The E phase was the most difficult to clean chemically and in the development of an etchant for this system several solutions which satisfactorily etched the bismuth or a phase were unacceptable because of their reaction with the E. It was found that a mixture of 50 ml lactic acid 30 ml nitric acid 20 ml (30 pct) hydrogen peroxide (Solution #1) was a satisfactory etchant for the a-matrix alloys. The samples were prepared as before and etched after 1 min of polishing with 3-p diamond paste. The etchant was applied by swabbing (light pressure) for 30 sec to 1 min and the sample was then rinsed in running water. The E has a slight stain and the a is fairly bright, Fig. 1.

Jan 1, 1965

By J. D. Rice, H. H. Rachford, G. H. Bruce, D. W. Peaceman

The problem of unsteady-state gas flow through porous media leads to a second-order non-linear partial differential equation for which no analytical solution has been found. In this paper a stable numerical procedure is developed for solving the equation for production of gas at constant rate from linear and radial systems. An electronic digital computer is used to perform the numerical integration using an implicit form of an approximating difference equation. Solutions are presented in graphical form for various values of dimension-less parameters. The solutions are compared with the laboratory study of gas depletion in a linear system. INTRODUCTION Production of fluids from porous rock reservoirs is essentially a transient process. Transient gradients develop as soon as production begins, and further withdrawals continue to cause disturbances which propagate throughout the reservoir, each adding in some way to the prior ones. A correct mathematical analysis of this behavior is complicated by the fact that the transient or unsteady-state flow of compressible fluids must be described by difficult second-order partial differential equations. As a practical matter, three distinctly different cases arise: 1. Flow of single-phase liquid 2. Flow of gases 3. Multiphase flow The first of these has been found to give a linear second-order equation similar to the well-known heat flow equation. where 7 is fluid density, 8 is time, and a a constant for the system, provided d 7 = r cdp, where the compressibility, c, is constant over the range of pressure, p, considered. Solutions of Equation (1) for both linear and radial flow are available in several forms.2'3' On the other hand. the second case, which is the flow of gas, gives a non-linear second-order equation, the solution of which is not known. Although a number of approximate solutions have been proposed, each is limited in value by the associated simplifying assumptions. Inasmuch as the analysis of transient flow is limited to liquid systems, a solution of the second case is necessary if further progress is to be made in studying underground fluid movement. For this reason a solution of Equation (2) was undertaken by means of numerical integration of approximating difference equations. BASIC DIFFERENTIAL EQUATION Equation (2; is derived by combining the equation of continuity, the perfect gas law, and Darcy's law to give the basic differential equation Strictly speaking, the fluids present in a gas reservoir are not perfect gases. Furthermore, there are indications that over certain velocity ranges, Darcy's law is not applicable. It would not be practicable. however, to attempt to obtain numerical solutions which would take into account all the possible variations from these laws which could occur in actual systems. The

Jan 1, 1953

By EDWARAD A. SIVEDENBORMG

REPORTS have been made at different times on the progress of water encroachment in the Frontier sands in the Salt. Creek oil field, Natrona county, Wyoming. All previous reports have, -however, been largely based on the position of water in the sands as determined by various physical tests. Subsequent information has been secured through a preliminary investigation of the porosity, grain size and degree of saturation of the Frontier sands. Also, a closer differentiation has been made between the waters encountered incident to the production of oil by means of chemical analysis. In view of the more recent developments there has been a need of a water encroachment map of the first Wall Creek based on a field survey and additional information acquired since the water encroachment map of the sand of 1926, by J. S. Ross and E. W. Henderson, petroleum engineers of the U. S. Geological Survey. The present report is confined to a study of the first Wall Creek sand and was written in connection with the preparation of the map, showing water encroachment in this sand. The first Wall Creek sand was the discovery sand in the field, the first well having been drilled in 1908. Its thickness averages 120 ft. and, varies between 90 and 160 ft. The sand is in the Colorado group of the Upper Cretaceous series and is further considered as a part of the Frontier formation found in other parts of Wyoming.

Jan 1, 1930

By NATHANIEI HERZ

(Cleveland Meeting, October, 1912.) THE formula very frequently used for computing the economical size of pipe to transmit compressed air is that of D'Arcy, as follows: d5(p1-p2)/w1l D-c w11 Where, D = the volume of compressed air delivered in cubic feet per minute,-at the final pressure. c = an experimental coefficient determined for the various sizes of pipe. d = the diameter of the pipe in inches. 1 = the length of the pipe in feet. P1 = the initial gauge-pressure in pounds per square inch. p2= the final gauge-pressure in pounds per square inch. W1 = the density of the air, or the weight in pounds per cubic foot at the initial pressure, p,. The most common case is that in which the given quantities are: the quantity of air required, the length of the pipe, and the initial pressure. The method of solution is to assume a pressure-loss and to compute the remaining factor, c/d5, thus giving the size of pipe corresponding to the assumed loss of pressure. It is always desirable to try two or more pressure-drops, in order to find the combination that is most satisfactory, since often a small change in the size of pipe will reduce or increase the loss of pressure several pounds. An alternative method is to assume a size of pipe and calculate the corresponding pressure-drop. Each method involves a series of tedious calculations to arrive at the most economical solution, and also requires the use of tables giving the constant, c, the actual diameters corresponding to the nominal pipe-sizes, the density of the air, w1, and often, for convenience, a table giving the

Dec 1, 1912

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselrnan Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo.

Jan 1, 1949

By Joseph Jensen

THE history of the normal oil field is supposed to show an oil graph stalting high in flush production, descending more or less steeply into the curve of settled production and dropping gradually to the vanishing point of economical operation. Together with this at somewhere in the early history of the field, there appears from a vanishing point a graph showing the production of water. During the period of settled production this graph rises higher and, toward the close, unless extensive work is done in the line of correction, rises far above the oil graph to where the cost of operation terminates profitable pumping. Fields that start out with a high relative content of water are generally very short lived. Fields that never develop a water problem are exceedingly rare.

Jan 1, 1930

By M. A. Cook

Sutherland used an ion-pair adsorption model to derive the author's hy-drolytic pee-acid) adsorption equation for the contact bubble curves of Wark and Cox. To do so it was necessary to postulate that the sum of coverages of surface anion sites by the collector and depressant anions is practically unity. It is here shown that the free energy of Sutherland's postulated collector ion (x-)-depressant ion (OH-) exchange reaction (for no other than the OH- to compete with X-), namely EX + (OH-) Z SOH- + X-, is in some cases positive and X- should not even adsorb. Also, in many cases the (OH-) adsorption must be quite negligible even though the collector covers only about a sixth of the mineral surface at the threshold of air bubble contact. This, however, contradicts the postulate that permits one to derive the correct bubble contact eqwztion for the ion-pair model. Furthermore, the requirement for charge neutrality leads in the ion-pair model to the (impossible) constancy of the ratio @+)/(OH-) along a contact bubble curve in which pH may change by more than seven units. HYDROLYTIC ADSORPTION EQUATION Hydrolytic (free-acid or free-base) and ion-pair (H', X-, or R', OH-) adsorption models of the collector in metal sulfide and similar flotation systems are superficially alike and somewhat difficult to differentiate. This is because they yield, under seemingly valid assumptions, equivalent forms of the equations describing the distribution of the collector between the aqueous solution and the mineral surface. This has been discussed by the author and associates1-4 and more recently by Sutherland,' both for simple collector-mineral and for more complicated collector-depressant-mineral systems. In the hydrolytic adsorption model the equations describing the contact bubble curves of Wark and coxeJ7 are as follows :2 Here X is the collector anion, D- the depressant anion, 9, and On are the fractions of the free-acid sites S on the surface of the mineral covered by collector and depressant free acids, respectively, and @ is the fraction of uncovered sites. Kx is the free-acid collector dissociation equilibrium con- stant, K1 that for the free-acid collector adsorption, KD that for the free-acid depressant dissociation, and K2 the equilibrium constant for the free-acid depressant adsorption. Eqs. 1 to 5 yield upon simultaneous solution the result is the critical free-acid concentration for bubble contact in the absence of depressant-free acid. Eq. 8 expresses the conditions along a simple collector-mineral contact bubble curve for the case HD = 0, or V = 0. Last and Cook showed that Eq. 6 applies generally and with good accuracy in the collector-depressant-metal sulfide mineral systems. Inci-dentally, it has been shown by infrared absorption studies that in some cases the free-acid adsorption process splits out water.' In this case, Eq. 2 might be written SHOH + HX Z SHX + H20, with a similar equation replacing Eq. 4 for depressant-free acid-water exchange. This possibility does not change, however, the basic equations or considerations of the hydrolytic adsorption model. Indeed, this type of free acid-water exchange reaction was predicted for fluorite and iron ore flotation by oleic acid in the dry grinding and boiling processes.410

Jan 1, 1961

By E. J. Westerman

Prealloyed powders of nickel-base superalloys were sintered to almost theoretical density in short sinterilzg times. It was ascertained that the rapid densification was caused by a small amount of liquid phase at the grain boundaries, which apparently ovriginated by incipient melting at temperatures considerably below those at which macroscopic melting of the compacts occurred. An increase in the quantity of liquid phase present during sintering-, caused by an increase in the sintering temperature, increased the densification rate, but resulted in a decrease in the room temperature tensile propevties. NICKEL-base superalloys, which presently comprise an important group of high temperature alloys, are difficult to fabricate by the forging, casting, and machining operations presently used. As it was felt that fabrication by powder metallurgical techniques might offer advantages in the production of super-alloy parts, a basic investigation of the most important process in the sequence of powder metallurgical operations, the sintering process, was undertaken on Rene 41, Udirnet 500, and Nimonic 90 and 100 powders. These alloys age harden by the precipitation of the ? Ni, rA1,Ti) phase. Nickel-base superalloys of the Nimonic type have been fabricated by powder metallurgical methods, and their mechanical properties reported in detail.' Other alloys for high temperature service which have been fabricated by powder metallurgical methods include a Co-base alloy of the Vitallium type;2,3 alloys with a Co-Ni-Fe-Cr base;4 stainless steels;5'6 Cr-W-Co alloys;" and a Co-base alloy, X-40.8 METAL POWDERS The superalloy powders investigated were: a) a prealloyed at.omized Rene 41 powder; b) a prealloyed atomized Udirnet 500 powder; c) a prealloyed atom-

Jan 1, 1962

By B. Yarar, J. Kaoma

[Introduction The critical surface tension of wetting of hydrophobic materials has been investigated extensively by Zisman et al. (1973) and relates the spreading of a liquid on a solid to the surface tension of this liquid. Thus, the Zisman ap¬proach shows that a plot of Cos 0 versus ?LV where, 0 is the contact angle and ?LV is the surface tension of that liquid in contact with its own vapor at equilibrium, produces a straight line which can be extrapolated to Cos 0 = 1. The intercept corresponds to a given ?LV, termed the critical surface tension of wetting. In instances, however, Cos 0 - ?LV plots show deviations from linearity. Alternative approaches have also included the plotting of adhesion tension (YLV COs 0) versus ?LV that can be interpreted in terms of critical surface tension data (Lucassen-Reynders, 1963). It has, on the other hand, been customary to correlate contact angle (0) with flotation data, although it is recognized that surface inhomogeneities and related contact angle hysteresis limit the interpretations pertaining to solid surface structures purely based on contact angle measurements. It is nonetheless true that 0 = 0, when the liquid is water, corresponds to a hydrophilic solid. Determination of ?c by contact angle measurements in conformity with the Zisman approach can encounter experimental difficulties, especially when solids are in a powder form. Following the reasoning that 0 = 0 corresponds to the hydrophilic state of a solid, froth flotation experiments can be expected to produce critical surface tension of wetting values for powders. The technique that consists of plotting recovery (% R) versus YLV data and extrapolating the linear part of the curve to % R = 0, has been described elsewhere (Yarar and Kaoma, 1984). This paper describes some of the results obtained by the extrapolation technique mentioned above, using various sulfide minerals. Experimental Materials Molybdenite (MoS2), sphalerite (ZnS), chalcopyrite (CuFeS2), chalcocite (Cu2S), and galena (PbS) were handsorted from massive samples and ground by mortar and pestle, and the -147 Fan fraction used in experiments; sulfur (S) was a C.P. Fisher Scientific Co. product. Method One gram powder samples were conditioned for three minutes in methanol-water solutions of predetermined surface tension values and the percents recovered by flotation using a Partridge-Smith Cell (Partridge and Smith, 1972), were plotted against each ?LV value. Results and Discussion The percent recovery versus ?LV for two naturally hydrophobic solids, i.e., natural molybdenite, MoS2 and sulfur are given in Fig. 1 where it is seen that ?c for sulfur is obtained as 31.5 mNm-1 whereas for MoS2, it is 26 mNm-1. Figure 1 also shows that the new flotation technique described, for estimating ?c is in good agreement with the Zisman method. Curves obtained by the same method for the minerals Cu2S, PbS, and ZnS are given in Fig. 2, where it is seen that for Cu2S, ZnS, and PbS, the extrapolation to % R = 0 produces ?c values of 36, 39, and 49 mNm-1, respectively. CuFeS2, on the other hand, gives a curve that does not permit such an extrapolation to obtain a ?c value with certainty. Nonetheless, treatment of the powder with 8.95 X 10-5 molar Na2S solution followed by washing with distilled water prior to flotation effects the curves as shown in the insert of Fig. 2. The type of curves given in Fig. 1 appear to be typical of hydrophobic solids as can also be observed in Fig. 3. The composition of solid and minute quantities of inclusions seem to play an important role as regards the surface properties of solids as reflected by the slope of the linear part of the % R - ?LV plot and thus the value of ?c obtained by this technique. For example, MoS2 of three different stoichiometric compositions produced the data given below. [MoS2MoS2.14Mo1.002S2 ?c mNm-126.029.031.0 dR/d?8.95.23.0]]

Jan 1, 1985

By F. von Gemmingen, E. J. Fasiska, L. Zwell

EARLIER studies of the dependence of creep on structure1 and of the dependence of creep rupture on creep behavior2 did not include detailed discussion of the phases present in the specimens under examination. It is of interest to determine the nature and amounts of such phases present since it is well known that these are dependent on composition, heat treatment and creep conditions.3 This investigation has therefore been undertaken to identify these constituents and to determine their relative amounts. This report presents the results of this investigation and describes an improved "extraction replica" technique developed in the course of the work. The composition of the Type 316 austenitic stainless steels studied in this investigation is given in Table I. The specimens were solution treated at 2000°F for 1/2 hr and water quenched. Those specimens subjected to prestrain at room temperature Methods for extracting precipitate particles from materials for electron and X-ray diffraction analysis have been described by Fisher,4 Smith and Nutting: and Booker and coworkers.6'7 Electrolytic extraction methods have been described by Andrews and Hughes.8 The first two methods have been used at this Laboratory, but have not proved satisfactory for many problems requiring X-ray diffraction analysis. It has been difficult to remove the replicas or to avoid tearing them during removal. These difficulties are overcome by backing the replica with a water-soluble plastic such as Dupont 51-05 Elvanol (polyvinyl alcohol). The backing increases the thickness of the replica so that it can be mechanically stripped from unloosened particles without folding or tearing. This procedure eliminates the stripping of wet replicas, which usually have a low tear strength. By stripping replicas after drying, it is possible to extract partially loosened particles which otherwise would remain imbedded in the metal. The modified method is as follows: after the specimen is polished, it is etched for 60 min in modified glyceregia consisting of 30 ml glycerol, 7 ml nitric acid, and 4 ml of hydrochloric acid. The sample is then washed, air dried, and coated with a 20 pct Baker and Adamson 1611 collodion (85 pct amyl acetate by volume) film. After the collodion film is dry (about 15 min), the sample is again etched in the modified glyceregia for 50 min, washed with isopropyl alcohol (to prevent dissolving the collodion) and air dried. A very thick coat of polyvinyl alcohol (about 50 pct solution "Elvanol Dupont 51-05" in water) is poured over the sample and is permitted to dry for about 24 hr. The composite film containing the precipitates is then stripped from the specimen and floated, polyvinyl alcohol side down, in water (at about 50°C) until the polyvinyl alcohol dissolves. This usually takes about 15 min. Should any of the polyvinyl alcohol remain on the replica, it does not give a crystalline diffraction pattern and therefore does not hinder identification of the precipitates. The extraction replica, floating in water, is picked up on a glass fiber and mounted in the Debye-Scherrer camera for X-ray diffraction analysis. Concentration of the etchant, and also etching time, had to be increased for several of the samples. Fig. 1 shows two extraction replicas taken from different areas of spec. M74-37; X-ray analysis showed a strong diffraction pattern of M23C6 and a medium one of u phase. A

Jan 1, 1962

By Walter R. Crane

PAGE I. Apparatus and Methods.......... 406 1. The Magnetic Circuit...........406 2. Apparatus Employed in the Traction-Method...... 406 a. The Coils............409 b. The Pole-Pieces..........409 3. Methods of Testing Fields Produced by Different Pole.Pices.. ..409 c. Testing with a Search.Coil........410 d. Testing with Iron-Filings and Glass Tube.. .. .410 4. General Forma of Pole-Pieces.........411 e. Flat Poles............411 f. Conical Poles........... 411 g. Spherical Poles...........411 h. Chisel-Edged (Chamfered) Poles.......412 II. Magnetic Fields...........412 5. Methods of Testinq for Magnetic Permeability...... 421 i. The Rod-Method..........423 j. Method Employed in These Experiments......424 k. Difference in the Results of the Two Methods..... 425 l. The Traction-Method.........427 m. Effect of Loosening the Charge.......430 n Corrections...........432 6. Theory.............433 o. Effect of Varying Weight on Tractive Force..... 434 p. Effect of Varying Pole-Distance.......436 q. Effect of Varying Magnetization.......436 T. Effect of Varying Size.. .......437 a. Summary,........... 441 III. The Relative Magnetic Permeability of Various Minerals,. 443 The form and strength of magnetic fields have attracted much attention. especially in connection with the designing of dynamo-electric machinery—an art which has been revolution-

Jan 1, 1902