Search Documents

By M. Cohen, C. Wagner, J. E. Reynolds

If the total volume of a diffusion couple changes during the diffusion, the measurement of distance becomes ambiguous. Use of distance parameters as suggested by Hartley and Crank is discussed. For small concentration differences, the standard form of Fick's second law is retained with conventional length units and the in- terdiffusion coefficient D. It is shown how D can be calculated from experiments involving large concentration differences and analyzed in terms of distance parameters. 'The merits of incremental diffusion couples involving small concentration differences are emphasized. THE conventional form of Fick's second law for one-dimensional diffusion of component B in a binary solution of A and B is where c, is the concentration of component B; x, the distance; t, the time; and D, the interdiffusion coefficient which may depend on ca. Hartley and Crank' have pointed out that Eq. 1 applies only if the total volume of the diffusion couple does not change during the diffusion process; otherwise, the definition of x becomes ambiguous. No change in total volume takes place if the specific volume of the solution is a linear function of the weight fraction Wb, or if the molar volume is a linear function of the mol fraction N. In some alloys, however, these relationships do not hold, and then it is necessary to introduce a modified measure of distance, 4 in order to retain the general form of Eq. 1. The application of Hartley and Crank's suggestions to diffusion in alloys has been discussed by Wagner.' Relation Between Measure of Distance and Units of Concentration The definition of [ depends on the choice of units for the concentration c,, as follows: 1—If the concentration ca is measured as the weight fraction W, (or weight percent), [ = 5, has to be defined so that equal increments of contain equal increments of mass m of the solution, e.g., dm = pSdx = Sdw [2] where p is the local density of the solution, and S is the cross-sectional area in sq cm which is taken to be constant in this problem of one-dimensional diffusion." * da Silva and Mehla have demonstrated the constancy of the cross-sectional area in the usual type of diffusion couple. However, experiments involving diffusion into thin wires4, 5 may exhibit changes in cross-sectional area, and therefore are excluded from the present treatment. Thus and the unit of is gram per sq cm instead of cm. 2—If the concentration c, is the mol fraction N, must be defined so that equal increments of contain equal numbers of mols of solution, e.g., dn= (S/V)dx= Sd [41 where V is the local molar volume of the solution. Thus dt, = dx/V [51 and the unit of is mols per sq cm. 3—If, as may be advisable in the case of interstitial solutions, the concentration C is measured in terms of the molar ratio of components B and A (c,, = Y, = nH/nA, where n and nl are numbers of mols of B and A), = Y has to be defined so that equal increments of contain equal numbers of mols of A, e.g., dnA= (NAS/V)dx = Sdf [6]

Jan 1, 1954

By W. H. Bassett, C. H. Davis

ALTHOUGH brasses and bronzes have been made for ages, a systematic study of their physical properties has been carried out only during the years of the present century. Among these properties may be included those which are to be detected by means of microscopic examination; in other. words by the science of metallography. The earlier workers in this field, both in this country and abroad, gave their attention to steel. When the senior author explored the situation in 1902, there was little encouragement to be found in undertaking the study of the non-ferrous alloys. A start was made, and the metallography of the brasses and bronzes, as well as of the copper-nickel-zinc alloys developed materially under his direction. Annealing experiments were begun in 1902, and in the succeeding years the effect of temperature, and the influence of previous working, on the grain size of brass were studied. The conclusions so well known and widely published today were largely reached during those earlier years. . In 1905 the first complete annealing series were made. By this it is meant that brass and copper sheet, 5 B & S Nos. hard, was machined into tensile test specimens, then annealed under accurate control for 30 min. at temperatures up to the melting point of the material. Various determinations were made, including tensile strength and elongation in 2 in. There rapidly followed similar series on all of the copper-zinc alloys from 100 to 60 per cent. copper, on the bronzes, cupronickels, and on copper-zinc-nickel alloys. At this point there was published by Grard, in October, 1909,1 the very comprehensive and complete work on the tensile properties of cartridge brass, 90-10 copper-zinc, and electrolytic copper. The excellent photomicrographs in that paper illustrated the changes in structure produced by cold rolling as well as by annealing at different temperatures, but where Grard's work was confined to copper and to two alloys, the investigations in this laboratory have been over the entire fields of the commercial copper-zinc alloys, copper-tin alloys, representative copper-nickel and copper-nickel-zinc alloys as well as aluminum bronzes and others of a more special nature.

Jan 1, 1928

By E. M. Baroody

MUCH information on intermetallic diffusion has been obtained in experiments in which two volumes, initially at different uniform concentrations, are maintained in contact at an interface which is plane, or nearly so. Concentration-distance curves are obtained after suitable times, and analyzed on the basis of a one-dimensional form of Fick's law In early work the linear equation to which Eq. 1 reduces when D is independent of concentration was used. However, when the initial concentrations c, and c, are appreciably different this simplification is often unjustified, and the suggestion by Matanol in 1933 of a way of avoiding it was welcomed. Matano's paper was based on work done as early as 1882 by Boltzmann.2,3 In 1938 Rhines and Meh14 reported an extensive investigation of systems in which the diffusion coefficient depends strongly on concentration, and included a detailed description of the Matano-Boltz-mann method. To a large degree, this description represents the formal method as it is understood and applied today, most later discussions having emphasized thermodynamic and mechanistic aspects of diffusion. Exceptions are the comments of R. V. Churchill, contained in a paper by Ham, Parke and Herzig,5 and the papers by Hall8 and by Kirkaldy.7 More discussion appears necessary since some aspects of the problem remain obscure. Better computational procedures are also needed. The common method, involving graphical determination of slopes and areas, is inconvenient and makes the estimation of errors difficult. Background of the Matano-Boltzmann Method Eq. 1 is to be considered along with initial and boundary conditions. Take the origin of x at the

Jan 1, 1958

By Charles H. Behre

KEYNOTE of the mining geology sessions was the preparation for an extensive war with all that this implies as to the need for strategic minerals, both metallic and nonmetallic. Nevertheless the sessions also included many papers of less urgent, more theoretical interest. The stress of wartime production had the effect of giving an unusually full and rich program, the longest in recent years, with sessions continuing virtually throughout the meeting. Some papers dealt with geophysical prospecting as applied to mining geology; others were concerned with the grand strategy of mineral reserves and thus involved the industrial minerals; such "borderline" subjects were presented before sessions held jointly with the Geophysics Committee or the Industrial Minerals Division.

Jan 1, 1942

By John Chipman, Theodore B. Winkler

IN order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chipman,3 dealt with the simplest possible slag system that would resemble those found in the basic open hearth-the slag system consisting of CaO-MgO-SiO2-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemistry of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, Si02, FeO, Fe203, P205, MnO, A1203 and CaF2, but not all of the slag samples contained all of these components at one time. REVIEW OF LITERATURE Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Brings4' von Samson-Himmelstjerna,5 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution ratios

Jan 1, 1946

By A. W. Hesse

The trend of American construction toward permanence and longevity is noticeable in the more recent coal plant installations; also, the policy of many coal operators has changed from seeking to obtain the desired tonnage from several plants of small capacities to designing a single installation to produce the whole amount. The mine openings and plant of the Nemacolin mine of The Buckeye Coal Co., are located on the Greene County side of the Monongahela River, 73 miles south of Pittsburgh. The map (Fig. 1) shows the general location, also the Lambert syncline. This syncline partly accounts for the selection of the site; the other reasons were the possibilities of rail and river shipments. Two shafts and a slope were sunk to the coal, work starting on all three in the second half of the year 1917. The air shaft was sunk to a depth of 243 ft. and completed in February, 1918; the slope was completed in November, and the skip shaft was stopped at a depth of 21 ft. below the coal, then the concrete lining was stopped 8 ft. above the coal August, 1918. Work on the skip shaft was resumed May, 1923, and sunk to a depth of 60 ft. below the coal by September, but it was not until May, 1924, that the lining was poured. Max. Min. WateR Water during after Sinking, Crouting, Depth or Cu. Yd. Cu. YD. Gal. per GaL. per Opening Size Length Excav. Conc. Min. Min. Air shaft..... 20 ft. diam. 251 ft. 8 in. 4788 1902 475 2 Slope........ 11 it. by 19 it. 1 in. 857 ft. 11500 5200 50 2 Skip shaft.... 32 ft. 8 in. by 12 it. 8 in. 296 ft. 6042 2293 300 3 Fig. 2 shows sections of these openings. The surface plan shows the relative positions of the openings. Coal was first hoisted from the air shaft May 7, 1918, and entry driving was continued; but the coal had to be stored, as the railroad had not been extended from Crucible to Nemacolin. As soon as the slope was driven to the coal and the linings concreted, the entries were driven along projected lines to connect with those advancing from the air shaft, and skip shaft. As soon as the underground connections had been made between the two shafts, the hoisting by buckets was inaugurated at the skip shaft and construction on the fan at the air shaft started.

Jan 1, 1927

By Henry Mulryan

DIATOMS are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skeletons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of vary-ing thicknesses. DIATOMITES Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition.

Jan 1, 1939

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, AI ARTHUR Morococlia, Peru, So. America. '95 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *ABE, MASAYOSHI, Prof. of Mining, Imperial University Kyoto, Japan. '05

Jan 1, 1910

By Donald D. Smythe

This paper describes briefly the topography and geology of the region where the mica-bearing pegmatites are found and discusses prospecting, the quality of the mica, its preparation, and evaluation of the deposits. Muscovite mica occurs in a number of widely separated localities in Brazil, but production has come largely from deposits in the southeastern and eastern part of the State of Minas Gerais (Fig. I). There the deposits form a discontinuous zone, which starts at a point go km. north of the city of Rio de Janeiro and extends north for some 500 km., roughly parallel to the coast. A maximum width of 180 km. is reached along the Rio Doce. To the west in Minas Gerais, and extending east into the states of Espirito Santo and Rio de Janeiro, the mica zone proper is fringed by areas in which there are scattered occurrences of mica-bearing pegmatites. A few of these outlying deposits have produced commercial mica, but most of them are unimportant. To the southwest, in the State of Sao Paulo, there are a number of mines, which at one time produced a very considerable amount of sheet mica, largely as a byproduct of kaolin mining. These deposits, and a few others lying between them and the main productive areas to the northeast, appear to be the southwestern continuation of the strong Minas Gerais mica zone. In the vicinity of Conquista, just north of the Minas Gerais boundary in the State of Bahia, and still farther north, near Jacobina, there are several known mica deposits. Their location indicates that they may be the northern continuation of the main mica zone. The major part of Brazilian mica production has come from four areas within the mica zone proper; from north to south, Governador Valadares, Raul Soares, Espera Feliz, and Muriaé.. The first is go km. from north to south and reaches a maximum width of 180 km. The Raul Soares area extends 135 km. from northeast to southwest, and in places is 80 km. wide. The Espera Feliz area is 100 km. from north to south, and reaches a width of 35 km. The Muriai. area extends 150 km. from northeast to southwest and its width reaches 40 kilometers. Between the known productive areas, and in the areas directly to the southwest and to the north of them, little mica has been produced. These gaps, as well as certain irregularities in the outline of the mica zone itself, are to be ascribed either to lack of prospecting or to conditions preventing the discovery of mica, rather than to its nonexistence. Elsewhere in Brazil mica has been reported from eastern Goiaz, Ceará, Pernambuco, Rio Grande do Sul, Matto Grosso, and Amazonas. Production from these sources is negligible at present. Because of the inferior quality of the mica from the more accessible of these localities, and the operational difficulties occasioned by the remoteness of others, it is improbable that they will become important producers for some time to come.

Jan 1, 1948

By Donald D. Smythe

This paper describes briefly the topography and geology of the region where the mica-bearing pegmatites are found and discusses prospecting, the quality of the mica, its preparation, and evaluation of the deposits. Muscovite mica occurs in a number of widely separated localities in Brazil, but production has come largely from deposits in the southeastern and eastern part of the State of Minas Gerais (Fig. I). There the deposits form a discontinuous zone, which starts at a point go km. north of the city of Rio de Janeiro and extends north for some 500 km., roughly parallel to the coast. A maximum width of 180 km. is reached along the Rio Doce. To the west in Minas Gerais, and extending east into the states of Espirito Santo and Rio de Janeiro, the mica zone proper is fringed by areas in which there are scattered occurrences of mica-bearing pegmatites. A few of these outlying deposits have produced commercial mica, but most of them are unimportant. To the southwest, in the State of Sao Paulo, there are a number of mines, which at one time produced a very considerable amount of sheet mica, largely as a byproduct of kaolin mining. These deposits, and a few others lying between them and the main productive areas to the northeast, appear to be the southwestern continuation of the strong Minas Gerais mica zone. In the vicinity of Conquista, just north of the Minas Gerais boundary in the State of Bahia, and still farther north, near Jacobina, there are several known mica deposits. Their location indicates that they may be the northern continuation of the main mica zone. The major part of Brazilian mica production has come from four areas within the mica zone proper; from north to south, Governador Valadares, Raul Soares, Espera Feliz, and Muriaé.. The first is go km. from north to south and reaches a maximum width of 180 km. The Raul Soares area extends 135 km. from northeast to southwest, and in places is 80 km. wide. The Espera Feliz area is 100 km. from north to south, and reaches a width of 35 km. The Muriai. area extends 150 km. from northeast to southwest and its width reaches 40 kilometers. Between the known productive areas, and in the areas directly to the southwest and to the north of them, little mica has been produced. These gaps, as well as certain irregularities in the outline of the mica zone itself, are to be ascribed either to lack of prospecting or to conditions preventing the discovery of mica, rather than to its nonexistence. Elsewhere in Brazil mica has been reported from eastern Goiaz, Ceará, Pernambuco, Rio Grande do Sul, Matto Grosso, and Amazonas. Production from these sources is negligible at present. Because of the inferior quality of the mica from the more accessible of these localities, and the operational difficulties occasioned by the remoteness of others, it is improbable that they will become important producers for some time to come.

Jan 1, 1948

By P. Bardzil, J. Gurland

An experimental study of the variation of transverse-rupture strength with composition Anexperimentaland grain studysize has shown that the strength reaches a maximum for values of the mean free path between carbide particles of 0.3 to 0.6 microns. The fracture oforiginates in and proceeds through the carbide grains mainly. Impact strength and hardness also were recorded. MOST of the physical properties of sintered carbides vary linearly with composition. The transverse-rupture strength, however, shows a unique behavior. As the amount of binder metal is varied from 6 to 25 pct by weight, the strength at first increases; then, between 15 and 20 pct Co, it reaches a maximum of nearly 400,000 psi, and finally decreases with further additions of binder metal. This behavior of the transverse-rupture strength has been reported, among others, by Englel and Sandford and Trent.' The significance of these observations has not been discussed in the literature. That it may be of more than specific importance is indicated by the very similar variation of strength with composition encountered in other systems sintered in the presence of a liquid phase, such as Tic-Ni3 and Fe-Cu.' Experimental Details All compacts were prepared and sintered according to normal industrial practice. The average diameter of WC grains and the mean free path between grains were measured on metallographically prepared samples by a method of linear and planar analysis sing the relations where d is the average diameter of dispersed grains; Nl is the number of noncontiguous grains intersected on a metallographic plane by a line of unit length; N, is the number of noncontiguous grains per unit area; P is the mean free path between grains of dispersed phase; and f is the volume fraction of dispersed phase. Approximately 1000 grains were counted on each sample. For each composition d2 was plotted against P, the resulting straight lines serving as a check on the measurements. The distribution curves of the WC powders of different average diameters were homologous, and no attempt was made to influence the grain size by blending powders, adjusting the sintering conditions, or otherwise altering the particle size distribution. Densities were measured by differential weighings in air and water. The degree of densification did not vary consistently with either composition or grain size. The density is influenced by slight amounts of impurities, specifically by 0.1 to 0.2 pct Fe which enters the powders during ball milling. As an illus- -tration of the experimental variations, a number of measured densities are listed in Table I. They are expressed in percentage of theoretical density, as calculated from the published X-ray densities of WC and Co.' For the purpose of determining the transverse-rupture strength, rectangular test specimens (3/16x 3/8x3/4 in.) were broken by loading at the center of a 9/16 in. span. The average strength of five or more samples is reported for each composition and grain size. The compacts were ground on two parallel surfaces only. The load was applied at an average rate of 6,800 psi per sec. Since the elongation after fracture of the alloys is very small, it was assumed that the compacts deform elastically to failure and the fracture stress was calculated by the conventional beam formula. The data for one alloy are presented in Table II as an example of the results and scattering ranges encountered. The precision of the test, as measured by the average difference between duplicates, is of the order of 15,000 psi. The results are strictly comparable only to compacts prepared and tested in the manner described and of similar chemical composition and grain size characteristics. Unnotched Charpy specimens were used for impact testing. Each point represents the average of 3 to 20 samples, the larger number being used in an attempt to determine the influence of grain size. Considerable scatter was encountered, the range from lowest to highest value often amounting to 30 pct of the impact strength. The hardness is reported as a Ra reading, using a 60 kg load with diamond brale indenter. Compositions are given in weight percent.

Jan 1, 1956

By W. L. Freyberger

In a study of the kinetics of flotation of coal, employing a single-cell continuous flotation system, Jowett and Safvi1 pointed out that it was experimentally impossible to float all of the coal which could be floated in a batch tests. On the other hand, deBruyn and Modi, in a discussion of their paper, suggested that under certain conditions the recovery of floatable material from a similar one-cell continuous system would have been 100%.2 Both of these pairs of authors make the assumption that a state of perfect mixing exist in the flotation cell. This assumption, usually made by investigators studying flotation kinetics in a continuous system, has been confirmed experimentally on several occasions. The work is summarized by Arbiter and Harris.3 It is the purpose of this note to demonstrate that, for conditions of perfect mixing, one of two conditions exist: 1) the recovery of floatable material is 100%, and the flotation is infinitely fast, or 2) the recovery of floatable material must be less than 100%. This theorem can be proved simply in the following manner: 1) If recovery, R, of the floatable material is 100%, the concentration in the tailing must be zero. This follows from the definition of recovery as

Jan 1, 1964

By Edwin S. Johanson, Ronald H. Wolk, Clarence A. Johnson, Harold H. Stotler, Katherine C. Hellwig

The H-Coal process, an ebullated bed reactor system for converting coal to liquid fuel, is described. Results from long-duration continuous flow bench-scale operations with Wyoming Wyodak, Arizona Black Mesa, and Utah Kaiparowits Plateau coals are presented. Economic data on the conversion of these coals to liquid products are given. The potentials of the H-Coal process in regard to coal from western producers is stressed.

Jan 1, 1974

United Engineering Trustees, Inc. GEORGE D. BARRON ARTHUR S. DWIGHT R. M. ROOSEVELT The Engineering Foundation H. C. BELLINGER E. DEGOLYER J. V. N. DORR

Jan 1, 1932

By W. M. Myers

Certain minerals possess inherent color and other properties that make them suitable for the pigmentation of paints, mortar, plaster, concrete, face brick, and other materials. Their production is one of the most ancient of mineral industries and their use by primitive man is well known. These natural pigments have some economic factors in their favor, particularly wide geographic distribution, low cost of production, ease of preparation, chemical stability, and permanence in use so that they continue to form the basis of a small but useful industry. When used in paints such pigments act as a filler and supply body and opacity in addition to color. Natural mineral pigments are prepared for the market by the comparatively simple operations of washing, grinding, blending, and calcining. Any one, or all of these processes may be applied to a single pigment. The development of synthetic pigments and the use of byproduct materials have introduced competition with the products of nature and are having a growing influence on the economic position of the mined minerals. Development of the Industry The industry developed to commercial stature in Pennsylvania largely because of the presence of beds of ocher extending from Easton in a southwesterly direction toward Reading, and a variety of small iron mines in the region. The mining of paint ores in the Lehigh Valley was active as early as 1850 and shortly after the Civil War the establishment of mills expanded production and led to the development of new products and eventually the manufacture of synthetic pigments. Pennsylvania continues to maintain it.s leadership as a producer of mineral colors. Production is recorded also in New Jersey, Illinois, Virginia, Ohio, and Georgia. Iron as a Pigment Iron in various compounds is the most important pigment in nature. The iron pigments are characterized by stability, light fastness, good covering power, high index of refraction, and economy in production. Ferrous compounds display a typical green coloration. This has not been employed as a commercial pigment to any great extent except incidentally in such greenstones as have been used in construction, or crushed and sized for application as a granule to roofing. Ferric oxides are characteristically red and form an important group of industrial pignents. Hydrated ferric oxides exhibit various shades of yellow and are present in such familiar pigments as ocher and sienna. The addition of small amounts of manganese oxide or carbon as organic matter to the yellows produces the brown umbers. Magnetite is one of the few black minerals that grinds to a black powder. The mineral pigments vary from earth colors of low intensity and great dilution of iron content to almost pure iron compounds with high tinting strength and correspondingly greater value. There has been some relationship between the mining of iron ores and the production of mineral pigments; although the production of colors is not carried on appreciably as a byproduct of iron mining. A number of mineral pigment producers, particularly in the eastern states, have operated mines which in the past were small producers of hematite, bog ore, or carbonate ore. The knowledge of the location of the deposit and its possibilities as a producer of pigment are due to its past history as a producer of metallic ore. Many iron compounds may be changed in color by calcination, the end product being Fe2O3, a stable red oxide. The yellow hydrated oxides may be changed to red. The gray carbonate, found in Carbon County, Pa., calcines to a fine red product. Ferrous sulphate (copperas) often available in tonnage as a byproduct of the steel industry, breaks down under heat or chemical action leaving a residual red oxide. Pigments produced by calcination or dissassociation of compounds possess the advantage of fine particle size and ease of grinding. Mineral Pigments MINERAL BLACKS Many black minerals grind to a light colored powder. This characteristic is familiar to the mineralogist as the white streak produced by a black

Jan 1, 1950

By John H. Schemel

Large Zircaloy-2 hammer or press forged bars did not exhibit the uniform excellent corrosion resistance to steam normally expected of the alloy in wrought form. Weight gains of coupons cut from forged bars were 40 to 60 mg per sq dm compared to the 28 mg per sq dm obtained on hot rolled sheet and strip. The mechanism of this corrosion and its relation to microstructure is discussed. After these observations, a solution heat treatment followed by rapid cooling was tried on coupons from eight heats of forged bars. The basket-weave structure resulting from the quench did not show agglomeration of intermetallic compounds. These coupons showed uniformly good corrosion resistance with weight gains very close to the 28 mg per sq dm expected of Zircaloy-2 after the 14-day steam test. A large forging was solution heat-treated and tested for structure, mechanical properties, and corrosion resistance. Corrosion resistance was excellent and uniform throughout the section. The normally anisotropic mechanical properties were changed to completely iso-tropic. Strength levels were raised while there was a small loss in ductility at the service temperature. Tempering of the quenched structure below the ß transus did not improve the ductility at the test temperature of 600°F. ZIRCALOY-2 end caps for nuclear fuel elements Zircaloy-2 is an alloy of 1.5 pct Sn, 0.1 pct Fe, 0.1 pct Cr, and 0.05 pct Ni, balance hafnium-free zirconium patented by Westing-house Electric Co. used in pressurized water reactors are machined from large hammer-finished forged bars. The bars forged for this application range from 3 1/2 in. to 7 1/2 in. squares. One of the tests used to evaluate Zircaloy-2 for this service is a 14-day exposure to very high-purity steam at 75oF and 1500 psi pressure. Normally wrought products will exhibit a black lustrous film of zirconium oxide after the test and show a weight gain of approximately 28 mg per sq dm. Coupons representing the forged bars exhibited a wide variety of corrosion results ranging from acceptable black coupons to some covered with white crystals of zirconium oxide that had weight gains of nearly 100 mg per sq dm. One of the most common effects was a white corrosion product that looked like a stain to some observers and the outline of massive metal grains to others. Very careful specimen preparation prior to the corrosion test did not affect the result and metallographic examination did not reveal a structural feature of a size and shape that would correlate with the corrosion product. In addition to the relatively poor corrosion resistance, the forged product was not as ductile as desired. The problem of obtaining uniform and more acceptable properties in these heavy-forged sections seemed to be a function of the microstructure of the metal and, in particular, the distribution of the intermetallic compounds. None of the four alloying elements however are appreciably soluble in a zirconium and are present as compounds which usually appear scattered randomly throughout the structure. Moudryl showed that the distribution of these intermetallic compounds in Zircaloy could be related to a ostringero corrosion failure. Grozier et al. discussed another structural defect that causes a similar corrosion effect. In this case, an elongated gas-void was determined to be the cause. M. L. Picklesimer held in his discussion of the Grozier paper that at least a part of the observed =stringersn were caused by the distribution of the intermetallic compounds. He proposed a

Jan 1, 1962

By Charles Will Wright

The application of the camera as an adjunct to topographic mapping began practically with its invention, and it has been employed with varying success since that time. With the exception of the camera to be described, the plate-camera has been universally used in this work, thus giving a projection of the area photographed on a flat surface. From such projections or photographs, by the rules of geometry and of perspective, points defining topographic features and seen from at least two camera-stations may be projected upon a ground-plane—the map.' In 1904 I employed the plate-camera for this purpose in Alaska, but found that the labor necessary to plot the maps, even in a general way, was long and tedious. In 1905 a small Eastman panoramic camera was fitted with spirit-levels, a sight-alidade and a transparent scale, introduced inside the camera to register the degree-points in the sky-line of the film-negative ; also, arrows to indicate the horizon-line. This was, on the whole, successful; but the details in the topography were not brought out in the views with sufficient clearness, aid the photographs were too small. These difficulties were overcome by obtaining a larger and more carefully constructed instrument, which was satisfactorily employed in the field during the year 1906. A panoramic view is made up of an integral number of perspective views upon flat surfaces, and logically is the most accurate and direct means to obtain an impression of a field of * Published by permission of the Director of the U. S. Geological Survey. Stanley, H. M. Photographic and Co-ordinate Surveying, Bans., xx., 740 to 766 (1891). Also, Flemer, J. ,4. Phototopographic Methods and Instruments, Report U. 8. Coast and Geodetic Survey, pt. 2, app. 10, pp. 619 to 735 (1897).

Jan 1, 1908

By H. Rush Spedden

Antoine M. Gaudin was a vigorously creative man and throughout his career an internationally respected leader of his chosen profession of mineral engineering. To his professional colleagues and clients and to his former students he was both "Professor Gaudin," their wise, inspiring, and enthusiastic teacher, and "Tony," their, warm and beloved personal friend. Thus, his teachings and his unique inquisitive-creative approach to problems live on and grow in the accomplishments of his students. Antoine Gaudin was born at the turn of the century in Smyrna, Turkey, where his father was general manager of a French-owned railroad. It was there that he spent his earliest years, literally in the shadow of classic marbles from diggings at the site of Aphrodesias, which his father had rediscovered. From this, Tony developed an appreciation of the arts. He eventually surrounded himself with art treasures; he reveled in the beauties of nature, and he cherished his choice collection of rhododendron and azaleas. His artistic traits led him to take up painting when his daughter, Elinor, sought his help in blending her tints for a water color. In typical fashion he was not satisfied until he had become adept with pastels in capturing the muted tones of distant landscapes and the technical properties of light and color. Unfortunately not many paintings were produced. His paternal grandfather was Marc-Antoine Gaudin, for many years secretary of the Academie des Sciences in Paris, and a well known chemist and mineralogist whose primary interests included the synthesis of precious stones. In an autobiographical sketch written in 1939, Dr. Gaudin recalled: "As a child I saw many of the original synthetic sapphires and rubies which my father had inherited. This, coupled with my father's avocation of mining ventures and archaeology, early decided that I would become connected with the mineral industry." One can speculate that the archeological activities of his father, the mineral systhesis experiments of his grandfather, and his own early studies of mineralogy and geology formed a base from which his special talents as an experimentalist were to develop. Laboratory research under Professor Gaudin's personal guidance was often an intensive, fast-moving, and exciting experience--especially to a new graduate student. First of all, Professor Gaudin was a highly skilled observer with seem-

Jan 1, 1976

By Morris Cohen, Robert C. Ruhl

Fe-Ni-B alloys were inresligated by X-ray diffraclion after splat quenching. Although this rapid cooling did not produce a measurable supersaturation of dissol1ed boron in either binary Fe-B or Ni-B alloys, a marked increase in dissolved boron was achieved by the splal quenching of lernary Fe-Ni-B alloys. Boron additions up to 2.0 wl pcl to Fe-13Ni and Fe-24Ni alloys cause an increase in retained austenite from 0 to 59 pet and to 92 pet, respectively. The martensitic phase in the Fe-13Ni-9 at. pct B alloy is .found to conlain about 0.6 at. pet interstitial boron, as evidenced by the tetragonality of this phase, and about 3.6 at. pct substilutional boron, us deduced from the lattice paratrieler decrease, the balance of the boron being precipitated as (Fe,Ni)aR. The austenitic Fe-Ni-B plznses also contain both interstitial and substitutional boron. Iron-Boron System. The phase diagram and related information about the solid solutions and intermediate phases in the Fe-B system are given by ansen,' Elliott.2 and Pearson.1 The equilibrium solid solubility of boron in both ferrite and austenite is quite small: the maximum solid solubility of 0.02 wt pct B (0.11 at. pct B) occurs in iron at the eutectic temperature of 1150°C. while the maximum solubility in a iron is less than 0.01 wt pct.l There is disagreement in the literature as to whether these solid solutions are substitutional or interstitial. Based on the measured activation energy of boron diffusion in iron, it appears likely that boron moves interstitially in austenite. 4 However, this observation does not rule out the possibility that some of the dissolved boron may also occupy substitutional sites in this phase. Investigations of internal friction of boron in iron have suggested that boron is interstitial there.' Shevelev, 5 on the other hand, reports a decrease in the ferrite lattice parameter with dissolved boron content, thus indicating a substitutional solution. Unfortunately. Shevelev's methods and analysis are unclear. Goldhoff and spretnak6 have measured the lattice parameters of pure iron and an Fe-0.005 wt pct B (0.027 at. pct) alloy at both room temperature (ferrite) and from 920° to 1200°C (austenite). They reporte: a lattice contraction in the ferrite of 0.0003 ± 0.0002 due to boron, thus indicating a predominately substitutional solution. Appreciable (0.0010 to 0.0060) lattice contractions were found in boron-containing austenites, but these effects were much larger than could be accounted for by the substitutional solution of all the boron present. Nickel-Boron System. Elliott 2 gives a summary of thephase diagram and recent work on this system. The solubility of boron in nickel reaches a maximum of 0.03 wt pct at the eutectic temperature of 1080°C. Iron-Nickel System. ansen' presents the equilibrium diagram for this system and also discusses the metastable austenitic and martensitic phases along with the a=? transformations. The lattice parameters of Fe-Ni ferrites have been recently redetermined by Abrahamson and Lopata.7 Their data, Fig. 1, show an unusual change in slope at about 1.7 at. pct Ni. Very few measurements of the lattice parameters of Fe-Ni martensites are available in the literature. The values of Roberts and Owen8 are considerably higher than those measured in the course of the present work: they find that a, is constant at 2.874? from 8 to 30 at. pct Ni. Both the slope change in the ferrite parameters and the occurrence of a maximum plateau in the marten-sitic lattice parameters vs composition denote the

Jan 1, 1970

By H. B. Small

The Ottawa river, the northeastern boundary of the Province of Ontario, and the dividing line between the latter and the Province of Quebec, has long been famous for the rafts of timber floated over its waters from the depths of the forest, and other poets besides Moore, have immortalized its beauties in verse. But with the ad vent of the railway which now pierces the forest solitudes, the days of rafting were numbered ; and the boat song is now heard no more on "Ottawa's tide," or at such long intervals only, that, when heard, it seems an echo of the past. The lumber trade is fast leav ing Ottawa City, the old headquarters of the business; and such square timber as is now cut is gradually finding other outlets than shipment to Great Britain, and other channels of transportation than the Ottawa river. Skirting the northern shore of this great river runs a vast chain of hills, assuming at times the altitude of mountains. Their geological character marks them as remnants of the earliest land of this conti nent. Following the course of the St. Lawrence from the Gulf of that name to the confluence of the river with the Ottawa, the course of which latter they then pursue, the range has been styled " the Lau rentians." Rolling in long undulations, with rounded, rather than rugged or pointed summits, they leave a margin of 8 or 10 miles, dipping in a gentle slope to the water's edge, rich for agricultural use, and dotted here and there with farms and settlements. Beyond this margin bold hills stretch northerly to blue mountains, rich in iron, lead, plumbago, and other minerals. The Apatite District.—One of these minerals is apatite, or phos phate of lime, the use of which as a material for the manufacture of superphosphate as a fertilizer has become the basis of the industry bidding Fair to prove ere long one of the chief elements of Canadian trade. So rapid has been the growth of this new industry that if the lumber business were to disappear from this mineral district, its void would be filled by that which has sprung up in connection with phosphate.

Jan 1, 1893