Search Documents

By Richard Moldenke

So FAR as the quality of the product is concerned, the history of the production of pig iron for foundry purposes is one of constant retrogression. The steps in this deterioration began with cold-blast charcoal pig iron, then anthracite iron, coke iron; then gradually warm to hot-blast coke iron, with the charcoal furnaces also heating their blast to get greater tonnages, and finally the present day hot-blast coke irons with scrap additions to the ordinary burden that, according to one European report, have gone as high as 135 per cent. Parallel with this quality retrogression is the enormous increase in furnace tonnages from about 15 tons daily to over 1000 tons per day in exceptional instances of modern practice. The key to this situation is economic pressure. The effect is a growing differentiation between furnace production for gray iron and malleable foundries and for the production of commercial steel. As the foundry is often compelled to draw upon the pig irons made for steel purposes, for economic reasons, whereas the steel industry does not draw upon foundry pig irons proper, the situation is resolving itself into one of grave consequence for the life of the gray-iron castings industry, and hence the intensive present-day feeling in foundry circles for rigid specifications to govern the quality of pig irons sold for foundry use. In the discussion of a paper on the use of scrap in the blast furnace held recently in the Institute, a very pertinent remark was made by one of the participating furnacemen, who confessed that "the things found wrong by the foundryman with his iron were beyond his depth." It may be added that those things are also beyond the depth of most foundrymen who, however, know from their results that they are getting poorer castings today with many pig irons than they did with those same brands in former years. Under the former fracture buying, the foundryman at least could select the strongest metal, as judged by the sledge, from various brands of similar fracture and pig section, and his results proved the soundness of his conclusions. With the advent of iron analysis, and in spite of the growing uniformity of the metal through greater tonnage

Jan 2, 1927

By AIME AIME

A METALLURGICAL research building is to be erected for the Armour Research Foundation at the Illinois Institute of Technology. It will be located at the corner of Federal and 34th Sts., Chicago, and fully equipped will cost $250,000. It will provide the Middle West with the largest and most complete of facilities for the conduct of developmental and industrial research in this field. The new building will be constructed around an existing foundry and metallurgical research building which has become too small to carry on and service the many research projects contracted for by the Foundation, having to do with steel, alloys, and nonferrous metals. After two bays of the new unit have been completed, the old unit will be torn down and the new one completed.

Jan 1, 1942

By K. E. Brown, F. W. Jessen

It is deemed feasible to store atomic reactor fuel wastes in salt dome cavities when the differential pressure acting on the cavity does not exceed 3,000 psi and the temperature is less than 400°F. Tests at pressure increments of 1,000 psi were conducted on a 2-in, cylindrical cavity contained in a 6-in. long X 6-in. diameter salt core. The cavity exhibited stability under pressures up to 3,000 psi and temperatures to 300°F. At temperature ranges of 100 to 400°F and with pressures of 5,000 psi and above continuous deformation of the cavity resulted. Initial movement of the salt was observed at all pressares. This was evidenced by vertical deformation and cavity size reduction. INTRODUCTION The development of storage techniques for safe disposal of atomic reactor fuel wastes is a goal of the Atomic Energy Commission. Salt domes have been used successfully for storage of liquefied petroleum gases and hence should prove to be suitable for liquid waste products of atomic reactors. The purpose of the following work is to evaluate the practicability of utilizing salt dome cavities for such wastes and to de-termine particularly the effect of pressure and temperature on a salt cavity. This work represents a part of a comprehensive study covering the over-all problem of storing re- actor fuel wastes in salt domes and/ or salt beds. The problem of accurately determining the stresses which exist in rocks in the earth's crust is indeed a complex one. Theoretical studies have differed widely in many of the basic assumptions about the physical properties of the rock itself. Some solutions of problems in underground stress analysis assume that rock is elastic, homogeneous and isotropic in character; others assume that rock possesses plastic, viscous, elasticovis-cous properties, or a combination thereof. Experimental evidence has shown that salt possesses plastic, viscous and elasticoviscous properties.' Recent work has shown that salt becomes more plastic with temperature.' APPARATUS AND PROCEDURE For experimental study a cylindrical cavity was chosen for analysis since it provided maximum volume per unit of depth with constant diameter. This particular cavity shape, allowing for irregularities, can be easily leached out of salt domes in field operations. For the purpose of approaching underground storage conditions as nearly as possible, the following factors were considered: (1) control of pressure and temperatures, (2) measurements of temperature gradients throughout salt mass, and (3) measurement of structural stability of salt cavities. In order to obtain triaxial pressure on the salt cavity without resorting to the application of fluid pressure directly on the salt mass, a system was designed whereby the same effect could be produced through axial loading only. By cutting a core to close dimensions to fit a steel test cylinder and applying axial pressure, a lateral pressure was obtained. This equipment is shown in Figs 1 and 2. A steel cylinder was made from

By Dennis Z. Mraz

An engineering procedure for designing the minimum separation between solution mined caverns in bedded salt deposit is described. The procedure is based on data obtained by in-situ and laboratory test methods. The formulae utilize the concept that salt rock under high pressure in a deep salt rock deposit would behave as a perfectly plastic substance, and that the active opening surrounding a typical cavern could be described by a circular ellipsoid. The paper describes the calculations required for the safe design of a solution mined salt cavern field.

Jan 1, 1984

By William Kranz

THE increased service demands on some of the products of the National Malleable Castings Co. prompted it about eight years ago to investigate the electric furnace, both in America and in Europe. The process bad' already been sufficiently developed in Europe to lead us to believe that the electric furnace would most nearly meet our requirements. After further investigation and consultation with the highest authorities on the subject, we decided upon the Heroult type as the simplest and most practicable. In 1910, we built a furnace of this type, of 300 lb. capacity, for experimental purposes, and although it was crudely constructed the quality of the material we were able to make justified the installation of a 6-ton Heroult furnace in 1912. This furnace has three electrodes, 17 in. in diameter, uses three-phase, 60-cycle current, and is equipped with Thury regulators, which give us good regulation and a uniform load on the line even when cold melting. The power factor of the furnace is 94 per cent. Since July, 1912, the furnace has been in continuous operation, producing up to the present time, over 20,000 tons of both carbon and alloy steels of varying analyses and of exceptional quality. Both cold-and hot-metal charges have been used, with a power consumption of about 150 kw-hr. per ton in the case of hot-metal charges and from 500 to 600 kw-hr. per ton in the case of cold charges. The electric energy consumed varies according to the final analysis of the steel and the amount of refining required. Too much cannot be said about the refining possibilities of the electric furnace, for no other method of steel manufacture can compete with the electric in this respect.

Jan 5, 1915

Organization Place Date 1919 American Railway Engineering Association Chicago, 111. Mar. 18-20 Society of Industrial Engineers New York, N. Y. Mar. 18-21 American Electrochemical Society New York, N. Y. Apr. 3-5 National Foreign Trade Council Chicago, Ill. Apr. 24-26 American Iron and Steel Institute New York, N. Y. May American Institute of Electrical Engineers Lake Placid, N. Y. June

Jan 3, 1919

By E. T. Turkdogan, P. Grieveson

Molten silver is equilibrated with silicon nitride at 1400°C in nitrogen + hydrogen gas mixtures, and from the solubility data the activity coefficient of silicon is found to be 1.76 at silicon concentrations below 1 pct. Using this value, and that available from the silicon cmbide solubility measurements, together with those derived from the phase equilibrium diagvam, the activities of silver and silicon are estimated for the entire composition range. The main feature of the activity data is that there is a pronounced positive deviation from ideality. The activity of silver in molten silver containing up to 5 pct Si was determined by Schadel, Derge, and Birchenall1 by measuring the vapor pressure of pure silver and of the alloy over a temperature range of 850º to 1050°C. They deduced from their results that there is a positive deviation from Raoult's law and that the activity coefficient of silver increases with decreasing temperature. However, as pointed out by Kubaschewski and Catterall,2 their activity coefficients are much too high, giving silver activities greater than unity. At a later date McCabe and Birchenal13 showed that the previous vapor pressure data on silver4 were high by a factor of about 1.3; presumably a similar error must have occurred with the vapor pressure measurements on the Ag-Si alloys. The activities of silicon and silver calculated by tager' from the phase diagram and by Gibbs-Duhem integration, respectively, show a positive deviation from Raoult's law for silicon activity and positive and negative deviations for the silver activity. According to these computations, at infinite dilution of silicon ygi = 1.12 at 1420°C. d'Entremont and chipman6 measured the solubility of silicon carbide in molten silver at unit carbon activity; the equilibrium silicon content is found to be Nsi = 0.017 ± 0.002 atom fraction for 1420°C. Using the data of Grieveson and Alcock7 for the free energy of formation of silicon carbide from pure silicon and graphite, the activity of silicon for unit activity of carbon and of silicon carbide is asi = 0.0308 at 1420°c; therefore for the above solubility data on silver, YSi = 1.81, which is somewhat higher than that given by Hager. Use is often made of silver alloys in the measurements of activities of solutes in metals where silver has a very low solubility; in fact, Ag-Si and Ag-A1 alloys have been used in the past for such purposes. In an attempt to gain more thermodynamic data on molten Ag-Si alloys, measurements have been made in the present study on the solubility of silicon nitride in molten silver; the results on these solubilities are given in this paper together with a detailed discussion of activities of silver and silicon. SOLUBILITY OF SILICON NITRIDE The standard free energy of formation of silicon nitride is known with a reasonably high degree of accuracy. According to the measurements made by Hincke and Brantle8 and by Pehlke and Elliott,' the following are the free energy data for the standard states of solid Si3N4, liquid silicon, and Nz at 1 atm pressure:

Jan 1, 1963

By Frank C. Roe

Two cogent and ubiquitous facts have supported a constant search by the ore processing industry for better wear resistant materials in equipment. First, designs and types of equipment change or improve continually to meet the economic and physical demands of different and/or leaner ores. Second, practically all equipment is subject to impact and abrasion conditions that probably are more severe and extensive than in any other industry. Development and testing by operators and equipment manufacturers alike, has produced an extensive variety of longer lasting metal alloys, rubber, plastics, ceramics and other materials to improve equipment performance under different specific conditions. The need for diversified materials becomes obvious upon the simple realization that no two beneficiation operations are identical. Among the variables in the handling of ore are: 1. Size and weight of ore particles. 2. Hardness and sharpness of ore particles. 3. Concentration of ore particles in liquid or gas suspension. 4. Velocity and direction of particle impact toward equipment surface. 5. Coefficient of friction between ore particles and equipment surface. 6. Temperature of operation. 7. Chemical environment of operation.

Jan 12, 1967

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942

By W. R. Ingalls

In choosing the unusual title given to this paper, in which the term "cyclic " might be substituted for "intermittent," my idea has been simply in respect of precision. We might say old method vs. new method, but that antithesis implies something of substitution that has not occurred and perhaps is not in sight. We may say horizontal retorts vs. vertical, but none of the older retorts are truly horizontal, and there are three different types of vertical retorts. Other complexities might be suggested. There is, however, a broad distinction between distilling that is accomplished in a periodic cycle, generally daily; and distilling that is accomplished continuously, irrespective of whether it be done in the vertical retorts of the New Jersey process or in the retorts of the Trollhät-tan process. In offering a summary of the present state of the art with the intermittent process, I shall not have any idea of exemplifying it through descriptions of any single plants, but shall rather divide among the main steps of the process and outline what is best developed among them. In pursuing this thought, it will manifestly be impossible to make a composition that will exemplify the acme of good practice, for the latter will always be a function of the cost of labor, fuel, etc., which are widely variable. As of 1929, in respect of labor we might generalize the average plant wage in the Pittsburgh-Wheeling district of the United States at $5 per day; in Oklahoma at $3; in Great Britain at $3; in Germany at $1.75-$2; in Belgium and France at $1. With high labor costs the metallurgist will naturally use means of the nature of mechanization that with low labor would be uneconomical when capital charges are taken into account. Nor may we from records of performance safely make positive deductions in respect of the efficiency of different types of furnaces unless they have been tested comparatively under identical conditions in the same works. We shall find gas-fired regenerative furnaces showing coal consumption from 1.2 tons down to 0.7 per ton of roasted ore, which may be ascribable to difference in the thermal value of the coal that is used or to differences in proportions of the parts of the furnace, which is something quite distinct from the principle of the furnace. Thus, we have

Jan 1, 1937

By R. L. Fleischer, W. F. Hosford

Tensile data for coarse grained aluminum Polycrystals suggest that the "grain size" effect is not due to dislocations piled up at grain boundaries but rather is primarily a relative size effect due to surface crystals being weaker and less confined. STUDIES directed at interpreting hardening of poly-crystalline metals normally identify their strain hardening properties with those in some particular type of single crystal.1"4 The recent recognition in face centered-cubic metals of a nearly linear stage with rapid hardening occuring at comparable rates for both polycrystals and single crystals, suggested that the same process or processes determine both cases and hence that there exists some justification for the use of single crystals to understand polycrystals. Further evidence for the above view may be found by an approach initiated by Chalmers:5 By using bicrystals of controlled orientation it is possible to begin to assemble a polycrystal and also to study grain boundary effects in detail. In this way it has been found that a single grain boundary affects easy glide but not the subsequent stage II hardening.6 This result suggests that a sensitive way to observe grain boundary effects in polycrystals would be to vary grain size and measure easy glide. As will be seen, easy glide is only possible for coarse-grained samples, and hence the results will serve to fill in the gap in measurements between single crystals and bicrystals on one hand and fine-grained polycrystals on the other. One problem inherent in comparing single crystals with polycrystals is the uncertainty as to what slip systems are acting in a polycrystal. To compare the two types of samples, rates of shear hardeninn---L. on the acting -planes are needed. and these may be computed only if it is known what particular systems are active. The acting systems were examined for a coarse-grained polycrystal and it will be shown that the systems supplying the preponderance of slip can be determined with little ambiguity. EXPERIMENTAL PROCEDURE Twelve samples of aluminum were prepared by chill casting into a heated graphite mold, followed by annealing at 635° ± 5°C for 24 hr with an 8-hr fur- nace cool, and finally either etching7 or electropol-ishing.' The samples, with a 7 to 10 cm length between grips and 4.4 by 6.6 mm in cross section, were deformed at a strain rate of about 3 10 -3 . per min in a tensile device which has been described elsewhere.5 The composition was reported by Alcoa as 99.992 pct Al, 0.004 pct Zn, 0.002 pct Cu, 0.001 pct Fe, and 0.001 pct Si; nine samples were deformed while immersed in liquid helium and three in air at room temperature. The stress-strain curve for one of the samples (P-1) deformed at 4.2 "K has been reported previ~usl~.~ This sample was selected for determination of active slip systems. Eighteen of the crystals were examined by optical microscopy to determine the angles of slip line traces and by X-ray back reflection to determine orientation. By this means the slip planes were determined and the resolved shear stress factors for possible slip systems could be computed. Finally each sample was sectioned so that after etching, the number of crystals could be counted for each of ten newly exposed surfaces. The average of these ten values will be termed n, the number of crystals per cross section. Values of 11, varied from 1.9 (nearly bamboo structure) to 12.7. Sketches of typical cross sections appear in Fig. 1. RESULTS AND DISCUSSION: SLIP SYSTEMS 1) Determination of Acting Slip Planes—The stress axis orientation and operative slip planes in eighteen crystals of sample P-1, as determined by slip line traces and crystal orientation, are summarized in Fig. 2. For one of the crystals two planes had a common trace. so that the traces alone did not distinguish which plane or planes were slipping. However it was found that the stress resolving factor for the primary system was 0.386, .while that for the most stressed system in the other plane (indicated bv the dotted arrow) is 0.138. It will be assumed tgerefore that only the primary plane acted. Since the orientations were determined after extending the samples 4 pct, the stress axes may be rotated from their original value by as much as 2 deg in some cases. It is interesting to note that in five crystals only one slip plane acted, in eight two acted, and in five three planes were observed—an average of two slip

Jan 1, 1962

By J. S., Douglas

IN 1880, the late James Douglas, LL.D., was superintendent of the Chemical Copper Co., operating the Hunt & Douglas process for the treatment of the siliceous copper ores of the Jones mine at Phoenixville, Pa. In conjunction with this a refining furnace was operated. After correspondence with Ben Williams, of Bisbee Ariz., who was commencing the mining and smelting of the Copper Queen ore. Dr. Douglas decided-to make his first journey to Arizona. While making plans for the trip lie visited a friend in Philadelphia, a .Mr. Logan, a prominent lawyer. He, through Professor Treadwell, brother of the discoverer of the great Treadwell gold mine of Douglas Island, Alaska, had an option with his min¬ing partner, Mr. Lenig, on the Eureka and Wade Hampton claims near the headwaters of the Verde River in Yavapai County, Arizona. These two claims, later the source of practically all of the wealth of the Jerome district, were then owned by C. P. Head and Co. Prescott merchants. Hugo Richards, banker, and formerly sutler at Camp Apache; Rod and John McKinnon prospectors and Nova Scotians; and perhaps one or two 'other owners of minor interests. Mr. Logan, hearing of Dr. Douglas intended trip to Bisbee, asked him to go first to see the two mining prospects, and this, Douglas, in need of the $500 fee, agreed to do as the time on the option on the claims was running short.

Jan 1, 1935

By William J. Coulter

WITHIN the United States the problem of meeting maximum production by our metal mines has been solved by: (1) Conservation of man power by mechanization. (2) Increasing man-power efficiency as expressed in tons per man-shift by the adoption of new and more efficient methods. (3) Production from submarginal properties made possible by some form of government subsidy. (4) Selective mining of high-grade areas. (5) Drawing on broken ore reserves and reducing advanced development work to a minimum. (6) Making maximum use of available equipment. (7) Repairing equipment that normally would be replaced. (8) Working a seven-day week on a three-shift basis to get maximum use of equipment and man power. (9) Adoption of incentive plans to increase maximum efficiency and unit production. (10) Important advancement in metallurgy, resulting in larger recoveries. (11) Improvements in safety, health, and general working and living condi-

Jan 1, 1945

By C. L. T. Edwards

IN the preparation of this paper, the author has drawn upon experience with the operation of a blast furnace on 100 per cent scrap burden, which he believes was the first operation of its kind in the country. It is the writer's further belief that much of the controversy attending discussions of this subject may be obviated by the presentation of a group of facts that should be known by blast-furnace men and open-hearth men alike. The following question has been raised: "Is iron made with scrap in the blast-furnace charge as good iron as that made without scrap-made with straight ore?" This question may be answered in part by the fact that the open-hearth men of the Bethlehem Steel Co. who used pig iron from a blast furnace that operated on 100 per cent steel scrap found no difficulty in the processing of such iron other than that to be expected from the known analysis. OPERATION WITH 100 PER CENT STEEL SCRAP During World War I, there was accumulated at the Bethlehem plant of the Bethlehem Steel Co. some 22,000 tons of alloy-steel turnings and borings. This scrap material was highly corroded and, like alloy-steel turnings of that period, were as a drug on the market. There was also a small tonnage of scale, rich in valuable metal. If this scrap could be worked up into pig iron, it would become readily available for use in the open hearth. In order that the pig iron should contain the maximum percentage of nickel, permission was obtained from the Management to try a 100 per cent scrap operation. Accordingly, a blast furnace was swung over on July 25, 1919; the percentage of steel scrap increased more or less irregularly until July 29, when l00 per cent steel turnings were charged. Except for occasional charges of nickel scale as an "extra," the operation continued uninterruptedly until Aug. 27, when the furnace was swung back to the regular ore-ore and scrap-operation. During this period, the furnace production ranged from a low of 568.60 tons to a maximum of 766.07 tons. At the swing-over from i00 per cent scrap to the regular burden, the charge hung up rather severely. While the latter condition has nothing to do with the object of the paper, a brief discussion of the experience will appear later because of the interest it may have for blast-furnace operators. In Table I, results of the first and last days of the ore charge are shown, July 25 and July 29. The last column shows a summary for the period of maximum scrap charge. The furnace employed had a hearth 16 ft. 0 in., bosh 22 ft. 0 in., stock line 15 ft. 6 in., bell 11 ft. 6 in., batter ¾ in., bosh angle 73° 27' and a Baker-Neuman top, with gas-engine blowers. Analyses Range of Material Charged Gravel: Si02, 64.40 to .7o.54 per cent; A1203,3-52 to 4.58; CaO, 7.27 to 9.49; M90, 5.09 to 6.14; FeO, 1.67 to 3.34, ignition loss, 9.50 to 13.83.

Jan 1, 1941

By T. D. Tiemann

The caustic extraction of silica from Wisconsin and Minnesota taconite was investigated by bomb digestion over the temperature range from 312 to 40S°F at caustic concentrations from 25 to 500 gpl. Residual concentrates containing as much as 65 pct iron were obtained. The high rate of silica extraction is related to a microcrystalline variety of quartz, since it is shown that the rate of extraction of silica from quartz is directly proportional to its surface area. Increasing dependence on foreign ore reserves makes the need for developing the technology necessary for treatment of our low grade ores even greater than it was at the time of World War 11, when much research was conducted on the extraction of alumina from clays. Representative of these were the studies carried on at the University of Illinois.' More recently, the U. S. Bureau of Mines investigated the production of alumina from anorthosite, and currently the aluminum industry is showing renewed research interest in this field. The studies reported here are part of a continuing research program based on the above concepts and aimed at the eventual development of processes for the treatment of low grade ores, particularly those of iron. The fact that large reserves 3 of low grade nonmagnetic taconite are contained in the iron formation of the Wisconsin Gogebic range have made this ore an important and attractive target for investigation. The idea of removing silica by caustic extraction is not new.495 The digestion in caustic solution of ground flint, diatomite, and other forms of chalcedonic silica is the basis for the production of soluble sodium silicates by the wet-process. Upgrading bauxites by the caustic extraction of silica has been investigated6 and is the subject of a German patent.7 Although mention is made by Roe' of the caustic extraction of silica from low grade Michigan and Wisconsin iron ores, and he lists a number of patents and references on the subject, recent work in the field does not appear to be extensive. As far as the author knows, there has been no work in this field on these particular ores. It is hoped that this paper will stimulate further investigation which will eventually lead to an econclmic means of processing these large low grade reserbes. TACONITES The taconites investigated in this study were from Minnesota and Wisconsin. That from Minnesota, a semi-taconite, Nas obtained from the Oliver Iron Mining Division, U. S. Steel Corporation, and represents a sample of an oxidized iron formation from their King Mine on the Mesabi range. The Wisconsin taconite came originally from the trench sampling of the U. S. Bureau of Mines, and represents a composite of the Norrie, Pabst, Yale, Plymouth, and Pence members of the Gogebic iron formation. Assays on these samples are given in Table I. A typical calcu1atr:d average analysis of the Wisconsin taconite is given in Table 11. Chemically, the Minnesota semi-taconite sample contains about 39 pct iron and 39 pct silica, while the Wisconsin taconite contains 30 pct iron and 53 pct silica, both on the dry basis.

Jan 1, 1962

By F. G. Smith

A FEW years ago, the writer encountered a, problem that, at first, seemed to be due to peculiar conditions affecting grain growth. Large cups made from heavy metal failed in the first drawing operation in the process of making seamless tubes. The metal, as cast, appeared to be sound and strong; it rolled successfully and withstood the first cupping operation, but on the first draw it failed, with a crystalline fracture. The failure appeared in the slightly worked part of the bottom of the cup, and microscopic examination revealed exceptionally large grains. Knowing the general conditions governing recrystallization of brass, which were later published by Matthewson and Phillips, an investigation was outlined with the idea of including various conditions under which new grains might form, and which would include the effect that a previous anneal might have upon the anneal following. These conditions were produced by annealing specimens of brass at five different temperatures, indenting them with a 10-inn. ball under four different pressures, and then reannealing at each of the five temperatures five specimens each of which had been annealed at one of the five temperatures.

Jan 8, 1919

By E. Miller, K. L. Komarek

Equatiorzs have been derived which related maximum solid solubilities in semicondcting compounds having retvograde solidus curves with 1iqllidus data. Liquidus curves in Lke Pb-Te, Pb-Se, ard PB-S systetris have been defermined by thertrzal aralyses. Fvotrz expevimental maximum solibilities ia CdTe, PbTe, uxd PbS vetvograde tetrperatures hale beep1 calculated. TIze resllts support the concept that under certaiz conditiots pronounced itjlections in the liquidis curves arc indzcatiz:e of retropade solidus curves and that the tenlperatltre of the lmaximum solid solubility will be close to the temperature of the point of inflection in the liquidus curve. The maximum solid solihility within a gvoup of homologous cottrpoods SeetlLs to increase with increasing flatness ol the liquidus curvres. The phenomenon of retrograde solubility in metals, i.e., maximum solubility in a solid terminal phase in equilibrium with a liquid phase, has been theoretically predicted by Van aar' in his calculations of hypothetical binary phase diagrams. It was not until 1926, however, that retrograde solubility was experimentally verified in the Zn-Cd system.' Since then many sys- tems with retrograde solubility have been found, so that at present approximately fifty binary diagrams with a retrograde solidus curve are known.3 Meijering4 has critically appraised the accumulated data and has presented calculations which alloy predictions as to whether or not a solidus line will be retrograde. Interest in retrograde solubility increased when it was found that the solidus curves of germanium and silicon alloyed with a great many doping elements are retrrade. The problem was treated thermody-namically by odkinson,% d all available data on solid solutions in germanium and silicon were summarized by Trumbore.7 Although it is to be expected that intermetallic compounds will also exhibit retrograde solubility, experimental evidence is much more limited. Until now retrograde solidus curves have been reported for the compounds de,' be, Ps:" ne," SnSe," and SnS.13 All these compounds are semiconductors, and the solidus curves were usually obtained by determining the carrier concentration at room temperature of samples equilibrated at elevated temperatures and then quenched. It has been hown,'' however, that it is not always possible to quench in the equilibrium compositions from above a certain temperature. Theoretical discussions have either explicitly excluded intermetallic compounds4 or not treated them with respect to retrograde slubilit.j In the following a thermodynamic treatment of retrograde solu-

Jan 1, 1967

By Waldemar Lindgeen

PART I.—General Features. PAGE Purpose and Extent of Inquiry ; Definitions (Fissure-Veins, Metamorphism, Metasomatism, Impregnation, Cementation, Weathering); Metasomatism in Connection with Mineral Deposits, Especially Fissure-Veins; Calcu lation of Analyses ; Criteria of Metasomatism; Crystallization of Sec ondary Minerals in Other Bodies; Secondary Alteration of Veins; Structure and Composition of Metasomatic Vein-Rocks and Their Rela tion to General Metamorphism,.759 PART 11.—Minerals Developed by Metasomatic Processes in Fissure-Veins. Quartz, including Chalcedonite and Opal; Rutile and Anatase; Fluorite; Calcite ; Magnesite and Dolomite ; Siderite; Muscovite and Sericite ; Biotite; Chlorite; Pyroxene and A mphibole; Garnet; Epidote ; Ortho clase ; Albite ; Tourmaline ; Topaz ; Kaolinite ; Zeolites ; Pyrite ; Mar casite ; Chalcopyrite ; Arsenopyrite; Pyrrhotite ; Galena; Zinc-blende and Other Sulphides; Tellurides; Native Copper ; Gold and Silver,. 601 Resistant Minerals,........... 619 PART III.—The Fissure-Veins Classified According to Metasomatic Processes. 1. Topaz-Cassiterite Veins (Altenberg and Zinnwald, Saxony ; Mt. Bischoff, Tasmania),..........620 2. Scapolite-Apatite Veins,.........625 3. Tourmalinic Gold-Copper Veins,.. 626 4. Biotitic Gold-Copper Veins,........ 641 5. Propylitic Gold and Silver Veins (General Features; Comstock Lode; The Veins of Nagyág, Hungary; Pachuca, Mexico ; New Zealand; Alaska ; Silver Cliff, Colorado; Silver City, Idaho),. .. .645 6. Fluoritic Gold-Tellurium Veins (Cripple Creek ; Other Occurrences),. 654 7. Sericitic and Kaolinitic Gold- and Silver-Veins (General Remarks; The Freiberg Veins ; De Lamar, Idaho; Summit District, Colorado),. . 6.58 8. Sericitic and Calcitic Gold-Silver Veins (The Gold-Quartz Veins of Cali fornia ; Idaho Types ; San Juan, Colorado ; Treadwell Mine, Alaska ; Gold Veins of Ontario, Canada; Schwarzwald Fissure-Veins),. . 664

Jan 1, 1901

By Dewitt T. Ring

Lack of reliable detailed production figures for earlier years, together with the loose nomenclature in reference to producing horizons and the application of the term "field" without any definite meaning or restriction, has made it impossible to gather statistical data suitable for the Institute's form. In common with all other producing areas in the United States, Ohio has felt severely the economic ills of the entire industry during the past year. With overproduction, not only of crude but also of refined products, going on throughout the country, the price structure as a direct consequence has weakened on Ohio oils. Valuable crude is being sold at a big loss today because producers arc willing to, and do, sell more than the market can absorb. The axe hangs heavy over the heads of Ohio producers, and will until something constructive is done to keep supply in proportion to demand. This not only applies to Ohio but to the entire industry. Production of Pennsylvania grade in Ohio was under 50 per cent proration, which has been in effect since Oct. 1, 1937. Three price cuts since February have lowered the posted price from $1.70 to $1.18, a 30 per cent reduction; other grades were less drastically reduced. Pipeline storage facilities were limited; many producers were faced with the problem of providing their own storage or the risk of ruining their wells. If they wanted to pull and abandon wells, there was no market for junk equipment. Many employees have been cut to half time and in a number of instances their services entirely dispensed with. Summary of Production and Drilling Both oil and gas production in the state during 1938 showed a definite decline over the previous year. (A table showing production by years from 1876 through 1937 was published in Vol. 127 of the Transactions.) The total production of crude oil in the state for 1938 was 3,357,914 bbl., as compared with 3,654,000 bbl. in 1937, a decrease of 7.1 per cent. At

Jan 1, 1939