Search Documents

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

By Charles A. Anderson

Arizona and western New Mexico contain 17 of the 25 leading copper mines in the United States. Production of molybdenite, lead, zinc, and by-product gold and silver is important. Precambrian ore deposits are largely limited to the Yavapai Series in central Arizona and most of the metal production has come from massive sulfide deposits, dominantly pyritic but containing different amounts of chalcopyrite, tennantite, sphalerite, and galena. Their origin has been interpreted by some geologists as hydrothermal replacement of schist, and by others as syngenetic deposits later metamorphosed. Most of the important ore deposits are of Mesozoic and early Tertiary age, dominated by the porphyry copper deposits spatially related to stocks, plugs, sills, or dikes of quartzbearing porphyritic to granular rocks. Host rocks for these deposits include the associated intrusive rocks, Precambrian schist and granitic rocks, Paleozoic limestones, Mesozoic(?) porphyritic andesite, and Mesozoic arkose and siltstone. Chalcopyrite and pyrite are the dominant hypogene sulfide minerals in the porphyry copper deposits, accompanied by minor molybdenite. The Questa deposit in New Mexico is largely molybdenite. Supergene sulfide minerals are chalcocite and minor covellite. Some ore bodies consist largely of hypogene sulfides, some are dominantly supergene sulfides, and others are mixed hypogene-supergene sulfides. Supergene oxide-copper minerals locally are important. Intense hydrothermal alteration accompanied the metallization in all of the porphyry copper deposits; five types are recognized, ( 1) propylitic, (2) argillic, (3) potassic, ( 4) quartz-sericite (without clay), and (5) lime silicate. The origin of the closely spaced fractures that contain ore minerals in intersecting veinlets is debatable; some geologists favor tectonic forces and others suggest cooling of magma or shrinkage due to alteration. Breccia pipes, veins, and limestone replacements account for some important deposits of Mesozoic and early Tertiary age, and presumably these are genetically related to the various intrusive rocks of this age. The St. Anthony deposit of Cenozoic age in southeastern Arizona is unique, consisting of a lead-zinc vein associated with later molybdenum and vanadium oxide-minerals. Cenozoic manganese deposits in western Arizona are an important resource in the Artillery Mountains, but the extent to which they may be exploited is a metallurgical and economic problem.

Jan 1, 1968

By Walter S. White

The Michigan native-copper district has produced about 5,400,000 tons of copper since mining began in 1845. The copper occurs primarily as open-space fillings and replacements in amygdaloidal flow tops and conglomerate beds of the Portage Lake Lava Series, of middle Keweenawan age. Secondary minerals with which the copper is associated include microcline, chlorite, epidote, pumpellyite, prehnite, quartz, and calcite; zeolites, other than laumontite, are not abundant. A zonal pattern of the secondary minerals transects bedding and suggests regional metamorphism mainly to the grade of the prehnite-pumpellyite graywacke facies of Coombs. Most of the major copper deposits are near the upper limit of abundant quartz in this zonal pattern. The distribution of copper in both amygdaloid and conglomerate deposits is controlled partly by primary permeability of the rocks and partly by later tectonic fracturing that was concentrated in the mechanically weak flow tops and sedimentary beds. Ore shoots and deposits are therefore controlled partly by primary structural features, such as areas of thick and thin fragmental amygdaloid or the boundaries of conglomerate lenses, and partly by regional structure: a number of ore deposits are in synclinal downwarps. The copper-bearing solutions that formed the deposits were ascending. They may have come from a large concealed intrusive, or may have been driven out of the porous tops of lava flows when the rocks were compacted and metamorphosed at great depth in the central part of the Lake Superior syncline. The second hypothesis seems more consistent with the widespread distribution of the copper, its relation to mineral zoning that represents truly regional metamorphism, its native state, and the likelihood that copper deposition was later than most or all of Keweenawan volcanism.

Jan 1, 1968

By D. B. RUSHNORE, K. A. Pauly

Bulletin. No. 41, May, 1910. ABBREVIATIONS. Al. Ind., Alliance Industrielle. am. Elec'n.. . American. Electrician. Bull. As. Ing. El Bulletin de la Association des Ingenieurs Elec- triciens Sortis de l'Institut Electrotecnique Montefiore, Liege. Bull. Soc. bilge d' Elec Bulletin de la Société belge d'Electriciens. Col. Guard . Colliery Guardian. D. R. P Deutsches Reich Patent. Dilly. Poly Dingler's Polytechniches Journal. E. & DI. Jour Engineering and Mining Journal. E. T. Zeit Electrotechnische Zeitschrift. Eclair. Elec. L'Eclairage Electrique. 1;1. Anzeig Elektrotechnischer Anzeiger

Sep 1, 1910

By M. Cohen, R. J. Teitel

There is considerable interest in beryllium because of its low density (1.84 g per cu cm), high modulus of elasticity (40 X 106 psi), high melting point (1280°C), and special nuclear characteristics. Moreover, it has fair resistance to corrosion and oxidation. However, the purest beryllium known to the authors is relatively brittle at room temperature, and cannot be fabricated readily. The search for improved properties leads naturally to investigations of beryllium alloys and the phase relationships upon which they are based. The present paper is concerned with the alloys of beryllium and iron, primarily from the standpoint of the equilibrium diagram. Iron was selected (1) because of its all-round importance in metallurgy, and (2) because the beryllium-iron system is known to be quite complex. The most recent diagram in the literature is that of Gaev and Sokolov,' and covers only the iron-rich end up to 16 wt pct beryllium. Beryllium markedly restricts the austenitic field, closing the gamma loop at about 0.4 wt pct (3 at. pct). On the other hand, beryllium is soluble in a-ferrite up to a maximum of 7.5 wt pct (34 at. pct) at the eutectic temperature of 1160"C. The eutectic composition lies at 10 wt pct beryllium (42 at. pct) and corresponds to a mixture of or and FeBez (called j3 in the present paper). The solid solubility of beryllium in the a phase decreases with decreasing temperature, and makes precipitation-hardening possible. These findings substantiate the earlier work of Oester-held,2 Wever and Mueller3 and Laissus.4 In addition to the FeBe2 (ß) mentioned above, Misch6 has reported on FeBes, and indicated evidence for another compound containing still more beryllium. A preliminary diagram by Gordon,5 not hitherto published, is given in Fig 1. Besides the phases previously named, there are shown a solid solution of extended range (e), a compound of limited solubility (t), and a high temperature phase (7). Beryllium is designated as 8. The t field contains the compound composition FeBea, and the f phase undoubtedly corresponds to the beryllium-rich compound found by Misch.6 The region around the { phase was proposed by R. J. Teitel based on Gordon's data. The details of the diagram are self-explanatory. It was the unusual complexity of this system that prompted the authors to undertake the present studies. By the same token, more emphasis was placed on the beryllium-rich than the iron-rich end of the diagram. Exprimental Details RAW MATERIALS The beryllium employed in this investigation was one of the purest grades available. Its chemical analysis after vacuum melting is given in Table 1. The metal assayed 99.4 wt pct beryllium. Vacuum melted electrolytic iron of purity shown in Table 1 was the source of iron.

Jan 1, 1950

By Mario L. Villa

Another increase in production and the discovery of new pools arc the outstanding developments of the year 1937. Production in 1937 totaled 16,354,706 bbl., compared to 15,457,953 bbl. in the previous year, an increase of 5.8 per cent, of which 5 per cent was due to the Yacimientos Petroliferos Fiscales (Argentine Governnlent Oil Fields) and 0.8 per cent t,o private companies. Table I shows that the most important gain in output was obtained in zone B of Comodoro Rivadavia, partly offset by a 5.7 per cent decrease in the Neuqu6n district. The fields of Salta and Mendoza show an increase of 4.4 and 39.1 per cent, respectively. The determination of bottom-hole pressures was started by Yaci-mientos Petroliferos Fiscales (Y.Y.F.) in Comodoro Rivadavia and

Jan 1, 1938

By Beverley S. Randolph

While our coal-mining practice, in regard to hauling on main roads, has advanced very rapidly in recent years by means of compressed air, electricity and ropes, that of gathering from rooms or working-places has remained almost stationary. Few large mines are without some method of mechanical haulage on main roads, but the gathering from working-places is still done almost entirely by means of animals or men. An effort to improve this has been made recently by the Consolidation Coal Company, under the direction of the writer, at its mines in the Georges Creek region. The seam worked is the Pittsburg bed, known locally as the " Big Vein." It is from 8 to 12 feet thick. Immediately overlying the coal there is from 5 to 6 feet of " rashings," consisting of thin alternating beds of shale and coal, which disintegrate rapidly on exposure to the air, and making a very treacherous roof. Rooms are driven from 12 to 15 ft. wide, with a single track close to one side. A line of posts is placed just far enough from this side to leave a clear space for the mine-car with a driver at the brake. This brings the post not far from the middle of the cross-bar, and provides more effectual support than if placed at the end. The tracks in these rooms are usually of 4 in. x 4 in. oak scantling, though of late years, owing to the advance in the price of lumber and the reduction in steel rails, more of the latter are being used. This track is laid by the miner. His pay for the work is included in the price per ton for mining. It is therefore, as a rule, unskillfully and often carelessly laid, and cannot be relied upon to carry safely any weight materially greater than the loaded mine-car. Compressed air was already in use on the main roads, driving motors weighing 30,000 pounds each, which were used to. bring the mine-cars that had been assembled from the rooms

Jan 1, 1904

By Richard Moldenke

So far as the quality of the product is concerned, the history of the production of pig iron for foundry purposes is one of constant retrogression. The steps in this deterioration began with cold-blast charcoal pig iron, then anthracite iron, coke iron; then gradually warm to hot-blast coke iron, with the charcoal furnaces also heating their blast to get greater tonnages, and finally the present-day hot-blast coke irons with scrap additions to the ordinary burden that, according to one European report, have gone as high as 65 per cent. Parallel with this quality retrogression is the enormous increase in furnace tonnages from about 15 to over 1000 tons per day in excep tional instances of modern practice. The key to this situation is economic pressure. The effect is a growing differentiation between furnace production for gray iron and malleable foundries and for the production of commercial steel. As the foundry is often compelled to draw upon the pig irons made for steel purposes, for economic reasons, whereas the steel industry does not draw upon foundry pig irons proper, the situation is resolving itself into one of grave consequence for the life of the gray-iron castings industry, and hence the intensive present-day feeling in foundry circles for rigid specifications to govern the quality of pig irons sold for foundry use. In the discussion of a paper on the use of scrap in the blast furnace held recently in the Institute, a very pertinent remark was made by one of the participating furnacemen, who confessed that "the things found wrong by the foundryman with his iron were beyond his depth." It may be added that those things are also beyond the depth of most foundrymen who, however, know from their results that they are getting poorer castings today with many pig irons than they did with those same brands in former years. Under the former fracture buying, the foundryman at least could select the strongest metal, as judged by the sledge, from various brands of similar fracture and pig section, and his results proved

Jan 1, 1927

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550°°F,) caused excessive grain growth and warpage, Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F,). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in, thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942

By THOMAS LEONBRD WATSON

I. INTRODUCTION. THE results embodied in this paper are based on a careful field- and laboratory-study of the lead- and zinc-deposits of the Virginia-Tennessee district, begun in the latter part of the summer of 1904 and completed in the spring of 1905, preparatory to the publishing of a State report .on them. A separate description of the individual deposits in Virginia is purposely omitted, since I have already described them in considerable detail in a State report. The Tennessee deposits are described here in some detail for the reason that no detailed record of them has yet been published. Practically, this paper summarizes the results obtained from a study of the geology of the ore-deposits of the district as, a whole. (I had the pleasure of visiting the deposits of Virginia and Tennessee with Dr. H. Foster Bain of the U. S. Geological Survey, in April, 1905. Figs. 21 and 22 are from photographs taken by Dr., Bail.) II. HISTORICAL. . The first authentic records of lead-mining .in Virginia date hack more than 150 years; and the old lead-mines at Austinville, on New river in Wythe county, V a., were the first to be worked. Colonel Chiswell, a native of Wales, and one of the earlier adventurers in southwestern Virginia, was one of the first operators of the Austinville mines. Chiswell's operations at Austinville commenced in the year 1750, and closed shortly after the beginning of the Revolutionary War, in the' year 1776, covering a period of about 25 years. From that time to the present, mining has been carried on almost continuously in the Virginia area. For many years after the Virginia mines were operated, mining was confined exclusively to the lead-ores. The zinc-ores

Mar 1, 1906

By D. R. Cook, W. M. Shepard, H. T. Morris

The East Tintic district in central Utah has produced ores of gold, silver, copper, lead, and zinc valued at more than $120,000,000. All of this ore has been produced from blind ore bodies in Paleozoic sedimentary rocks that are concealed beneath hydrothermally altered volcanic rocks and cut by intrusive bodies of Eocene age. The Paleozoic rocks, which range in age from Early Cambrian to Mississippian form the core and limbs of a large, northtrending asymmetric anticline that is cut by low-angle thrust faults, high-angle transcurrent faults, mineralized fissures and faults, and normal faults that are both older and younger than the mineralized fissures. The ore bodies generally may be grouped into two classes: ( 1) massive replacement bodies that are rich in silver, lead, zinc and manganese and (2) fissure veins that are valuable primarily for their content of gold, copper, and silver. The replacement ore bodies are localized chiefly in the Middle Limestone Member of the Ophir Formation of Middle Cambrian age where it has been thrust-faulted against older or younger rocks and cut by northeast-trending mineralized fissure zones. The fissure veins primarily are productive only in the Lower Cambrian Tintic Quartzite. Extensive lowgrade deposits of lead-zinc-silver ore recently have been discovered in Devonian carbonate rocks in the Lower plate of the East Tintic thrust fault but as yet are unevaluated. The principal guides to ore include: ( 1) intersections of northeast-trending fissures and crossbreaking faults that brecciate the carbonate rocks; (2) zones of late-stage pyritic, calcitic, and sericitic alteration in the lavas; ( 3) primary geochemical anomalies in the altered rocks; and ( 4) mineral zoning patterns of the known ore bodies. The present development of the Burgin mine would seem to assure the continued productivity of the district for at least a decade.

Jan 1, 1968

By K. P. Gupta, A. K. Pal, L. Chandrasekaran, U. P. Singh

The Mn-Sn binary system, investigated at the high-manganese end and between 500° and 1000° C, shows four phases at temperatures below 727"C, namely the u Mn, the p Mn, the Mn3 Sn, and the Mn, Sn phases, while at higher temperatures only the last three phases remain stable. The solubility of tin in a Mn is very small and the maximum solubility of tin in P Mn phase appears to be abollt 10 at. pct Sn. The solubility range of the Mn,Sn and the Mn, Sn phases is 23.0 to 26.0 and 37.0 to 40.0 at. pct Sn, respectively. The lattice parameter of the 13 Mn phase increases with increasing tin content. The Mn, Sn thase is hexagonal with and appears to be basically of the Ni3 Sn type structure except that for quite a few X-ray diffraction lines the calculated and observed relative intensities do not agree well. The Mn-Sn binary system has been studied by several investigators.''~ Their results indicate that three intermediate phases, namely, the Mn3Sn, Mn,Sn, and MnSn, phases, exist at high concentrations of tin. However, so far the proper phase equilibrium has not been established at the manganese-rich end and very little data is available for the composition range between pure manganese and Mn3Sn. Moreover, earlier investigators differ in their opinion about the exact composition range at which the Mn3Sn and Mn,Sn phases appear and some doubt has been cast by some investigators3 regarding the structure of Mn3Sn phase which has been reported to be isotypic with Ni3Sn (Mgscd type) structure. In this investigation an attempt has been made to establish the proper phase equilibrium between pure manganese and Mn + 50 at. pct Sn composition in the temperature range of 500" to 1000°C. PROCEDURE The raw materials used were from three different sources. For exploratory work five alloys containing 5, 10, 15, 20, and 25 at. pct Sn were prepared using 99.9 pct pure manganese and tin supplied by E. Merck & Co., Germany. The rest of the alloys and one more 25 at. pct Sn alloy were prepared using 99.9 pct Mn supplied by Gallard Schlesinger Chemical Mfg. Corp., U.S.A., and 99.999 pct Sn supplied by Semi Elements Inc., U.S.A. Weighed amounts of manganese and tin were melted in recrystallized alumina crucibles in an inert gas (argon) high-frequency induction melting furnace. By careful control of temperature and time of melting the losses were reduced to below 0.2 pct in all cases. Since the losses were very small, no attempt was made here to analyze the samples chemically. Alloys were wrapped in molybdenum foil and sealed in small evacuated fused silica capsules. The alloys were annealed at different temperatures, controlled within + l°C, for sufficiently long periods to attain proper phase equilibrium, and subsequently quenched in cold tap water. The annealing periods used at different temperatures were 15 days at 500°C, 7 days at 600°C, 5 days at 700" and 750°C, 3 days at 800°, 850°, and 900°C, 2 days at 968"C, and two alloys annealed at 968°C were reannealed for 10 hr at 1000° C. From each annealed specimen, a part was utilized for metallographic study while another piece was used for X-ray diffraction study. 1.0 pct HNO, solution and oxalic acid solutions of concentrations 0.05 to 1.0 pct were used for etching Mn-Sn alloys above and below the MnsSn composition, respectively. Since all alloys were brittle, X-ray specimens were prepared using the as-crushed -325 mesh alloy powders. Only one 25 at. pct Sn alloy powder was reannealed in an evacuated silica capsule at 800°C for 5 min and water-quenched. X-ray diffraction patterns . for the Mn3Sn phase with the as-crushed and the reannealed powders did not show appreciable change. Un-filtered iron radiation at 25 kv, 15 ma was used with either Norelco 114.6-mm-diam Debye Scherrer Camera (for phase identification) or Norelco 12-cm-diam symmetrical focusing camera (for lattice parameter determination of the 6 Mn phase). The estimated accuracy of lattice parameter determination for the focusing camera was * 0.001A. RESULTS AND DISCUSSIONS The results of metallographic and X-ray diffraction study made with different alloys are shown in Fig. 1. The variations in lattice parameter with composition for the p Mn and the Mn3Sn phases are given in Tables I and 11, respectively, and the lattice parameter as a function of composition for the p Mn phase is shown in Fig. 2. The lattice parameter of the p Mn phase increases with increasing tin content while for the Mn,Sn phase the data obtained from two two-phase alloys and one single-phase alloy indicate increase in a,, and decrease in c, parameters with increasing tin content. The results, Fig. 1, indicate that the solubility of

Jan 1, 1969

By R. G. Grieves, G. Thodos

A method is presented for the accurate calculation of the cricondentherm and cricondenbar pressures of multicomponent hydrocarbon mixtures of known composition. The mixtures may contain six and quite possibly any number of components including paraffins, isoparaffins, olefins, acetylenes, naphthenes and aromatics. The approach is similur to that used for calculating critical pressures and cricondentherm and cricondenbar temperatures. The critical pressure, the normal boiling point and the approximate vapor pressure behavior of each component are all that art required. A stepwise culculation procedure is necessary for mixtures containing more than two components. From an analysis of 22 binary systems and 118 mixtures, the average deviation of calculated cricondentherm pressures from reported values is 2.4 per cent. For nine multicomponent mixtures the average deviation is 1 per cent. Considering 19 binary systems and 108 mixtures, the average deviation of calculated cricondenbar pressures from reported values is 1.7 per cent. For 15 multi-component mixtures, the average deviation is 2.2 per cent. INTRODUCTION A knowledge of the phase behavior in the critical region of multicomponent hydrocarbon mixtures is of value both in industrial processing operations and for the optimum operation of gas condensate reservoirs. Accurate methods of calculating the critical temperatures and critical pressures4,6,7,8,9,23 and cricondentherm and cricondenbar temperatures6p10 of multicomponent hydrocarbon mixtures are available in the literature. If the cricondentherm and cricondenbar pressures could be calculated with equal accuracy, the entire phase diagram of a multicomponent hydrocarbon mixture could be well approximated. The work of Etter and Kay6 is limited to systems containing the normal paraffins and has not been tested on systems containing a heavier component than heptane. In addition, the development of their multicomponent equations is based upon a limited number of mixtures containing from three to six components. Silverman and Thodos have considered systems containing both paraffinic and non-paraffinic hydrocarbons, but their correlation is limited to binary systems and is highly inaccurate for methane systems. Eilerts has done extensive work on the cricondenbar pressure; he has produced an excellent correlation for binary systems. However, his procedure for multicomponent mixtures is chiefly useful for highly complex mixtures requiring a knowledge of the vapor-liquid equilibrium behavior of the mixtures; he has not considered the cricondentherm pressure. The objective of this study was the development of an accurate and rapid method for the calculation of the cricondentherm and cricondenbar pressures of multicomponent mixtures containing all types of hydrocarbons and having a wide volatility range. The approach that was adopted is similar to that used by Grieves and Thodos for cricondentherm and cricondenbar temperaturesl0 and for critical pressures.9 However, methane systems had to be considered separately and a modified stepwise calculation procedure was utilized for the cricondertherm pressure. The correlations were developed in a manner similar to those for critical pressures and cricondentherm and cricondenbar temperatures. Based upon binary data reported in the literature it was observed that the ratios of cricondentherm and cricondenbar pressure to the pseudocritical pressure (molar average), pt/ppc and pp/ppc, respectively, in two-component systems depended upon the mole fraction of the low-boiling component and upon the diversity in properties of the two components. A dimensionless boiling-point parameter Tb,/Tb was chosen to represent the diversity in properties of the components. For a binary system, Ti,'is the molar average of the normal boiling points of the two components involved. For a multicomponent system it is either the molar average of the normal boiling points of all of the components involved or the molar average of the normal boiling point of the pure low-boiling component and of the atmospheric boiling point of the low-boiling-free mixture of

Jan 1, 1965

By Ogden Tweto

The Leadville district, on the west flank of the Mosquito Range in central Colorado, has produced silver, zinc, lead, gold, and minor metals valued at $512,000,000. The ore deposits are in a sequence of dolomites and quartzites, Cambrian through Mississippian in age and about 500 feet thick, which is extensively intruded by porphyry sills, dikes, and plugs of Tertiary age. The sedimentary rocks and sills dip about 15°E and are broken by many faults, which are predominantly of nearnorth trend and downthrown to the west. The ore deposits are principally blanket or manto replacement deposits, but in the eastern part of the district many veins occur also. The replacement deposits are largely confined to three dolomite units in the stratigraphic sequence. Of these, the uppermost or Leadville Dolomite is the most productive. Most ore bodies are on the underside of porphyry sills and, particularly, beneath sills that occupy unconformities. Many replacement bodies have vein roots or branch from veins. The veins occupy faults and are productive mainly in the section of quartzites and dolomites and included sills. The primary ores consist principally of pyrite, marmatitic sphalerite, and galena but locally contain chalcopyrite, silver minerals, bismuth minerals, and gold. Principal gangue minerals are manganosiderite and jasperoid. The ore deposits have a crude zonal pattern centered around an intrusive center at Breece Hill, which evidently influenced ore deposition thermally. The ore deposits were oxidized to depths of several hundred feet in Miocene time. Bonanza ores mined in the early days were characterized by cerussite, cerargyrite, and embolite. Later, zinc carbonate ores were identified and mined on a large scale. The Leadville district is a complexly faulted and intruded area at the intersection of major fault systems trending N20°W and N15°E in the Mosquito Range. The intensely fractured area evidently localized igneous intrusion and subsequent mineralization. Ore solutions rose on many of the faults in the area, presumably from the same source as the porphyry magmas. Movement on these faults continued into the Pleistocene, displacing ore bodies, oxidation zones, Pliocene sediments, and glacial deposits.

Jan 1, 1968

By Richard Moldenke

So FAR as the quality of the product is concerned, the history of the production of pig iron for foundry purposes is one of constant retrogression. The steps in this deterioration began with cold-blast charcoal pig iron, then anthracite iron, coke iron; then gradually warm to hot-blast coke iron, with the charcoal furnaces also heating their blast to get greater tonnages, and finally the present day hot-blast coke irons with scrap additions to the ordinary burden that, according to one European report, have gone as high as 135 per cent. Parallel with this quality retrogression is the enormous increase in furnace tonnages from about 15 tons daily to over 1000 tons per day in exceptional instances of modern practice. The key to this situation is economic pressure. The effect is a growing differentiation between furnace production for gray iron and malleable foundries and for the production of commercial steel. As the foundry is often compelled to draw upon the pig irons made for steel purposes, for economic reasons, whereas the steel industry does not draw upon foundry pig irons proper, the situation is resolving itself into one of grave consequence for the life of the gray-iron castings industry, and hence the intensive present-day feeling in foundry circles for rigid specifications to govern the quality of pig irons sold for foundry use. In the discussion of a paper on the use of scrap in the blast furnace held recently in the Institute, a very pertinent remark was made by one of the participating furnacemen, who confessed that "the things found wrong by the foundryman with his iron were beyond his depth." It may be added that those things are also beyond the depth of most foundrymen who, however, know from their results that they are getting poorer castings today with many pig irons than they did with those same brands in former years. Under the former fracture buying, the foundryman at least could select the strongest metal, as judged by the sledge, from various brands of similar fracture and pig section, and his results proved the soundness of his conclusions. With the advent of iron analysis, and in spite of the growing uniformity of the metal through greater tonnage

Jan 2, 1927

By Charles W. Bloomquist

The profitability of miscible flooding in a hypothetical target oilfield is examined. The major costs, including Windfall Prof it Tax, are identified and their re1ative importance are discussed. The sensitivity of profit to important physical and economic variables is evaluated and discussed, including variance in oil recovery, oil price, injectant requirements, injectant cost, and capital requirements. Economic sensitivities to important development and operating decisions such as timing, Spacing, Slug size, and gas recycling are also analyzed. The Windfall Profit Tax (WPT) as it applies to gas miscible EOR projects is reviewed. The effect of WPT on each of the various project cases is analyzed and the effect of reduced WPT on remaining production from existing operations is evaluated. Tax implications are compared for integrated vs. "independent" controlled projects and the alternative of expensing vs. capitalizing tertiary injectants is also evaluated. The impact of the Net Income Limitation in reducing WPT. during early and late project life is determined and discussed.

Jan 1, 1982

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942

By William Kranz

THE increased service demands on some of the products of the National Malleable Castings Co. prompted it about eight years ago to investigate the electric furnace, both in America and in Europe. The process bad' already been sufficiently developed in Europe to lead us to believe that the electric furnace would most nearly meet our requirements. After further investigation and consultation with the highest authorities on the subject, we decided upon the Heroult type as the simplest and most practicable. In 1910, we built a furnace of this type, of 300 lb. capacity, for experimental purposes, and although it was crudely constructed the quality of the material we were able to make justified the installation of a 6-ton Heroult furnace in 1912. This furnace has three electrodes, 17 in. in diameter, uses three-phase, 60-cycle current, and is equipped with Thury regulators, which give us good regulation and a uniform load on the line even when cold melting. The power factor of the furnace is 94 per cent. Since July, 1912, the furnace has been in continuous operation, producing up to the present time, over 20,000 tons of both carbon and alloy steels of varying analyses and of exceptional quality. Both cold-and hot-metal charges have been used, with a power consumption of about 150 kw-hr. per ton in the case of hot-metal charges and from 500 to 600 kw-hr. per ton in the case of cold charges. The electric energy consumed varies according to the final analysis of the steel and the amount of refining required. Too much cannot be said about the refining possibilities of the electric furnace, for no other method of steel manufacture can compete with the electric in this respect.

Jan 5, 1915

Organization Place Date 1919 American Railway Engineering Association Chicago, 111. Mar. 18-20 Society of Industrial Engineers New York, N. Y. Mar. 18-21 American Electrochemical Society New York, N. Y. Apr. 3-5 National Foreign Trade Council Chicago, Ill. Apr. 24-26 American Iron and Steel Institute New York, N. Y. May American Institute of Electrical Engineers Lake Placid, N. Y. June

Jan 3, 1919