Search Documents

By Robert E. Goodwin

There are four main requirements to be considered in selecting a wire rope that will provide the best service. A proper choice is made by correctly estimating the relative importance of each of these requirements and choosing a rope with qualities that will best enable it to withstand the combination of destructive forces expected under continued service. A Good Rope Choice Matches Strength with Stress A wire rope should be (1) strong enough to sup- port the maximum load anticipated with a proper safety factor, (2) able to withstand bending and to resist bending fatigue without failure of the wires, (3) able to withstand surface abuse such as abrasion, pounding, and wire scrubbing, and (4) able to take abuse such as crushing and distortion.

Jan 5, 1969

Asarco's Sacaton unit, located near Casa Grande 45 miles southeast of Phoenix, Arizona, was brought into production in February 1974. Ore reserves are estimated at about 48 million tons at 0. 95% copper. Mineralization of the orebody comprises both sulfides and oxides, with minor amounts of gold and silver. Preproduction stripping of 40 million tons of overburden was accomplished in less than two years. Mining is done at the rate of 9,000 stpd ore with a waste-to-ore ratio of 4.6 to 1. 0. The mine is developed on 40 ft benches, and by 1979 underground block caving methods will be phased into the operation at a depth of 1900 ft. Ore is mined in the pit two shifts per day, seven days per week, and is hauled with 85 ton trucks to the primary crushing plant. Trucks dump their loads into a 165 st capacity pocket equipped with a chain curtain which controls the ore flow to the 6 ft 6 in. wide by 24 ft long (2. 0 m by 7.3 m) vibrating feeder grizzly. Grizzly bars are inclined at a 5º slope on the first half of the 0 feeder and 10 on the last half. Grizzly bars have 6 in. (13 mm) spacings which pass 60 to 70% of the mine-run ore. Grizzly oversize drops into a 48 in. by 60 in. (1. 22 m by 1.52 m) primary jaw crusher. Both the grizzly undersize and crusher discharge are collected on a 42 in. (1.07 m) conveyor belt operating 398 fpm (121 mpm) for transport to the 4,750 live st intermediate storage area ahead of the fine crushing plant. Capacity of the Sacaton primary crushing plant is a nominal 1150 stph (1043 mtph). It operates fourteen shifts per week with an effective crushing time of four hours per shift. An economical open-air design was used, but an enclosed operator control room is located on the upper level where the dump truck, feeder, and crusher can be observed. Oversize rocks are removed from the feeder or crusher by the 10-ton bridge crane. Direct operating costs for this well-designed primary crushing plant, including labor, power, supplies, and maintenance, are only 3.5 cents per short ton. An interesting feature of the Sacaton orebody is that the non-sulfide copper minerals, which are less prevalent than the sulfides, occur intimately with the sulfide minerals; for this reason, all ores as mined are treated in a flotation circuit using sulfidizing methods for oxide recovery.

Jan 1, 1978

By John M. Kelly

This report covers the development, exploratory drilling, and production of oil and gas in New Mexico during 1945. The statistical information was gathered from state regulatory agencies and other sources believed to be reliable; it is presented here in combined form for general information only, and the author assumes no responsibility for its accuracy or completeness.

Jan 1, 1946

By Archer E., Wheeler

Producing copper companies were active during 1941 owing to the national defense program the United States and the requirements of the friendly belligerent nation. This activity extended to the American owned properties in South America, the major part of whose product was taken by the Metals Reserve Co., a U.S. Government agency. Anaconda Copper Mining Co. is building a new converter plant at Anaconda, with four units of the Peirce-Smith type. The addition is being built adjacent to the reverberatory plant so as to avoid the necessity of hauling matte and slag. It is expected to be completed this year.

Jan 1, 1942

C. Q. Payne, New York City: Prof. Blake's inference that magnetic separation may be successfully employed upon smithsonite and iron oxide, after a preliminary roasting, is confirmed by the fact that this separation has been carried on with entire success for over a year at the works of the Wythe Lead and Zinc Mine Co., Austinville, Va. The ore mined on this property is a mixture consisting chiefly of galenite, smithsonite and limonite. The crude material is crushed, screened and washed in log washers for the removal of clay, and then jigged for the separation of the galenite. The zinc-and iron-ores are then roasted in reverberatory furnaces, being turned and moved towards the bridge-end of the hearth by manual labor. The roasted material contains from 20 to 26 per cent. of metallic iron. The slight difference in the specific gravities and the friable condition of the ores after roasting prevent the separation of the oxides by means of jigging. It was therefore the practice, previous to the use of magnetic separation, to charge the roasted material directly into the retorts of the zinc-furnaces. The rapid cutting of the retorts under this practice proved a serious inconvenience and expense. In the spring of 1892, the writer built for the Wythe Lead and Zino Mine Co. a magnetic separator which embodied several novel features and which was designed to treat the roasted zinc- and ironoxides. This separator has proved entirely successful for the purpose for which it was designed. During the first nine months of its operation, 1415 tons of 2240 pounds of roasted material were passed through the separator, producing about 675 tons of heads carrying from 50 to 55 per cent, of metallic iron, which are sold to a neighboring blast-furnace. The tailings, which contain the zinc, carry from 4 to 6 per cent. of metallic iron. For magnetizing the iron-ore previous to separating it from the zinc-ore, no change whatever mas made in the form of the reverberatory furnace previously employed. It was found that, by charging near the bridge-end of the hearth, toward the end of the roast-

Jan 1, 1894

A mine in the mountains of southeastern British Columbia is fast earning a reputation as the safest metal mining operation of all time. Already officially proclaimed as the safest mine in Canada, the H.B. mine of The Consolidated Mining and Smelting Co. of Canada (Cominco) continues to advance its safety performance far in the lead of average accident frequencies in mines across the country. Official recognition came its way again this spring when the Cominco mine was awarded the John T. Ryan trophy for the fourth time in the last five years. This award is emblematic of top national safety performance of a metal mining operation. The H.B. mine is its only four-time winner. The Ryan award is based on a frequency of accidents involving lost time of more than six days. In each of the years that the H.B. has won the award-1958, 1959, 1961 and 1962-its frequency was zero, with no accidents involving a time loss of more. than six days

Jan 12, 1963

By W. D. Potter, E. T. Peters

Single-crystal films of boron have been prepared by thermal reduction of purified BCl3 with subsequent deposition of boron onto oriented silicon substrates. The structural properties of films prepared under various experimental conditions have been determined by light microscopy and "grazing-" angle electron-diffraction analysis. An orientation relationship is proposed for silicon and a-rhombo-heclral boron which can be described as: (111)Si (112)B; [110]Si [110]B ElEMENTAL boron is known to have a high energy gap* and consequently has potential value as a high- *Energy gaps of 1.35 to 1.55 ev1-3 and 2.0 ev4 are reported for ß-rhombohedra1 and a-rhombohedra1 boron, respectively. temperature semiconductor.5 Exploitation of this property, however, has been hampered by the unavailability of pure, single-crystal boron. Two recent symposia6,7 have treated the subjects of purification, crystallization, crystal structure, and properties of boron and provide a foundation for further investigation in these areas. The structure, lattice constants, and observed ranges of stability for four reported polymorphs of boron8°12 are listed in Table I. The rhombohedral structures are generally accepted as true polymorphs whereas the tetragonal structures are believed to be transient. Most currently available single crystals of boron are grown by Czochralski and floating-zone methods. Unfortunately, these crystals generally contain numerous defects and are highly strained as a result of the polymorphic transformations and thermal contractions which accompany cooling. Recently, Armington, Potter, and Tanner13 have reported the formation of single-crystal films of boron on silicon single-crystal substrates through thermal reduction of BC13 by hydrogen. Boron E. T. PETERS, Junior Member AIME, is Senior Scientist, ManLabs, Inc., Cambridge, Mass., and W. D. POTTER is Research Chemist, Air Force Cambridge Research Loboratories, L. G. Hanscom Field, Bedford, Mass. formed at temperatures near 1000°C was identified as the a-rhombohedra1 form, consistent with expectation. The present paper describes a continuation of this work with specific reference to characterization of the structural features of the deposited boron films. The ultimate goal of this program is to produce large-area single-crystal films of a-rhombohedra1 boron to be used for electrical and optical studies by other workers. PREPARATION OF BORON FILMS The experimental procedure of preparing thin films is similar to that described by Theuerer14 for the epitaxial growth of silicon by thermal reduction of SiC14 and has already been described as applied to the preparation of boron thin films.13 Briefly, a mixture of BCl3 vapor and dry hydrogen is passed over a heated silicon substrate. Thermal reduction of the BC13 allows deposition of boron on the substrate. The substrates were {111}-oriented, single-crystal silicon. Square specimens 0.63 cm on an edge by 0.1 to 3.0 mm thickness were prepared by

Jan 1, 1965

By H. Rush Spedden, A. M. Gaudin

IN the belief that a critical study of its operating problems might be a sound investment, the Cuban American Manganese Corporation initiated an ore-treatment research in cooperation with the Massachusetts Institute of Technology. One of the early objectives of this research naturally became the relationship of the microscopy of the Cuban ores of the Corporation to their flotation treatment. The operations in Cuba have already been described by F. S. Norcross, Jr.7 and the laboratory study of manganese oxide flotation goes back a number of years .4 Broadly speaking, the difficulties encountered in the flotation of manganese ores are that the consumption of reagents is extremely high, the concentrate contains more silica than is desirable and the tailing losses are relatively high. An appreciable betterment on any of these scores would achieve a definite betterment in costs, quantity of minable ores, and quality of product. The microscope study discussed in this paper was made on samples from the Quinto mine, from the Ponupo mine, and from mill products at various stages of passage of the ore through the mill. The writers have had access to Company records and in particular to the petro¬graphic studies made on thin sections of ore by the late Professors R. J. Colony and Philip Krieger, of Columbia University. They acknowledge their debt to both of these men for the help derived from the reports. Manganese oxides are black, friable, smudging. It is, therefore, very difficult to judge operations by inspection. The mineralogy of manganese compounds seems to be confused, and the authors believe that many more minerals have been described than actually exist. Much of this difficulty is due to the prevalence of the structural conditions that will be discussed further in this paper; namely, the porosity and the friability of the ores, and the extremely intimate association of minute manganiferous mineral crystals with impurities of various sorts. By all odds the most important manganese mineral in Cuba is the one that in this paper is called "psilomelane." The name "psilomelane" has been used in so many different ways that the choice of it for this ore may not be approved by all. However, it seems to be the best under the circumstances. This mineral accounts for about 97 per cent of the manganese in the ores of the Quinto and Ponupo mines and in the mill feed. The remaining odd 3 per cent consists mostly of pyrolusite together with minor amounts of other manganese oxide minerals. DESCRIPTION OF PSILOMELANE Aggregate Structure In grains or lumps, psilomelane has a characteristic fibrous appearance and seems

Jan 1, 1942

By Earle Schumacher

THE solidus line above the solid solution field in the lead-antimony system was originally determined by Dean and his associates1 from heating curves. They did not regard this line as having been accurately fixed and in their more recent publications2 the curves drawn do not follow closely the original data. The precise location of the solidus line is of importance in the extrusion of lead-antimony cable sheath, as the temperature of the metal in this process must be less than the lowest temperature at which any part of the alloy in the lead-press charge becomes liquid. It is very desirable, however, to operate at as high a temperature as possible, as the rate of extrusion for a given pressure is approximately doubled for an increase of 10° C. in temperature. The precise location of this line is also important, in the investigation of ternary systems of lead, antimony and a third metal. For these reasons, and because of the differences reported in the literature, data were secured on the lead-antimony solidus line by the classical quenching-test procedure.

Jan 1, 1927

By Shiou-Chuan Sun

DISCUSSION shiou-chuan sun (author's correction) - Too late for revision, the author realized that the data on stability of froth presented in this paper were not based on the same height of froth column. It is recommended herein that the stability of froth is better calculated by dividing the time elapsed until the froth disappeared by the volume (in cu cm per sq cm) or height of the froth column, and is expressed in sec per cm. The stability data in Tables I, II, and III of this paper were recalculated, in accordance with this recommendation, and the results are shown respectively in the accompanying Tables VII, VIII, and IX. Compared with Tables I, II, and III of the paper, the stability data of Tables VII, VIII, and IX are more reliable in disclosing the persistence of froth of various frothers having different frothabilities. For example, the conclusion given in the paper that the stability of froth is generally proportional to the volume of froth becomes invalid when the stability of froth is expressed in sec per cm, as shown in Tables VII, VIII, and IX. Table VII shows that both the stability and volume of froth increase with the addition of small amounts of n-hexyl alcohol, and that further additions of n-hexyl alcohol decrease the stability but increase the volume of froth. Table VIII indicates that the stability of different types of frothers is governed by their chemical composition and is difficult to predict from their frothability. Table IX shows that the stability of different frothers with similar nonpolar groups tends to increase with a decrease of the hydro- philic property of their polar groups, and consequently with the decrease of their solubilities. This is further substantiated by the fact that the stability of frothers, as listed in Table IX, is generally lowered by the solvent effect of absolute ethyl alcohol. Table IX shows also that the stability of froth tends to increase with the decrease of the volume of froth* provided the frothers used have similar nonpolar groups and dissimilar polar groups.

Jan 1, 1953

By Shiou-Chuan Sun

DISCUSSION shiou-chuan sun (author's correction) - Too late for revision, the author realized that the data on stability of froth presented in this paper were not based on the same height of froth column. It is recommended herein that the stability of froth is better calculated by dividing the time elapsed until the froth disappeared by the volume (in cu cm per sq cm) or height of the froth column, and is expressed in sec per cm. The stability data in Tables I, II, and III of this paper were recalculated, in accordance with this recommendation, and the results are shown respectively in the accompanying Tables VII, VIII, and IX. Compared with Tables I, II, and III of the paper, the stability data of Tables VII, VIII, and IX are more reliable in disclosing the persistence of froth of various frothers having different frothabilities. For example, the conclusion given in the paper that the stability of froth is generally proportional to the volume of froth becomes invalid when the stability of froth is expressed in sec per cm, as shown in Tables VII, VIII, and IX. Table VII shows that both the stability and volume of froth increase with the addition of small amounts of n-hexyl alcohol, and that further additions of n-hexyl alcohol decrease the stability but increase the volume of froth. Table VIII indicates that the stability of different types of frothers is governed by their chemical composition and is difficult to predict from their frothability. Table IX shows that the stability of different frothers with similar nonpolar groups tends to increase with a decrease of the hydro- philic property of their polar groups, and consequently with the decrease of their solubilities. This is further substantiated by the fact that the stability of frothers, as listed in Table IX, is generally lowered by the solvent effect of absolute ethyl alcohol. Table IX shows also that the stability of froth tends to increase with the decrease of the volume of froth* provided the frothers used have similar nonpolar groups and dissimilar polar groups.

Jan 1, 1953

By L. L. Anderson, R. E. Wood, W. H. Wiser

Western bituminous coal can be processed to low sulfur liquid fuels by fast reactions. A process (LEFCO) under development at the University of Utah uses coal and catalyst under hydrogen pressure to convert 60 to 70%of the coal matter to fuel liquids and gases. Coals have been processed in small diameter (less than %in.) tubes and at reaction residence times of less than 10 secs. Effects of process variables on the yield and quality of products have been studied. General features of the process and the properties and characteristics of the products produced are presented. Special features of the process that distinguish it from other liquefaction processes under development are also discussed.

Jan 1, 1977

By W. D. Forgeng, P. F. Wieser

MnSi alloys containing from 2 to 24 at. pct Si have been investigated by metallographic and X-ray methods. Contrary to published data, the temperature of the ß-manganese to a-manganese transformation is lowered by the addition of silicon. The existence of two additional intermediate phases E and ( is demonstrated. E, ranging in composition from 12 to 15.5 at. pct Si, forms by a peritectoid reaction between ß manganese and the second new phase, (. The latter phase is homogeneous at silicon contents from 16.2 to 18 at. pct and forms peritectically from the 0 phase and liquid. The eutectic reaction occurs between the ( phase and MnsSi rather than the ß phase and Mn3Si. As a result of this investigation, a modification of the manganese-rich section of the MnSi equilihrium diagram is proposed. The binary diagram of Mn-Si, according to Hansen,' Fig. 1, exhibits in the low-silicon region (below 24 at. pct Si) a peritectic transformation at 900°C of 0 manganese + Mn3Si to a manganese as determined by R. Vogel and H. Bedarff2 as well as a thermal effect at 980°C between 16.2 and 22.6 at. pct Si reported by the same authors. The nature of the latter transformation was unknown. K. Amark, B. Boren, and A. westgren3 reported indications that possibly four more phases existed in the range of 10 to 27 at. pct Si. The present investigation deals with the phase relations in the range of 2.1 to 17.7 at. pct Si. A few spot checks were conducted up to 23.84 at. pct Si. EXPERIMENTAL PROCEDURE Small experimental heats were prepared by induction melting in a vacuum furnace using argon as a protective atmosphere. The crucible was of commercial-quality magnesia. The furnace charge consisted of silicon metal and dehydrogenated electrolytic manganese. The typical analysis for these materials is shown in Table I. The molten alloy was tapped into 2-in.-square, 7-in.-long ingots. After visual inspection, a small quantity of alloy in the middle portion of the ingot was separated for use in this investigation.MnSi alloys containing from 2 to 24 at. pct Si have been investigated by metallographic and X-ray methods. Contrary to published data, the temperature of the ß-manganese to a-manganese transformation is lowered by the addition of silicon. The existence of two additional intermediate phases E and ( is demonstrated. E, ranging in composition from 12 to 15.5 at. pct Si, forms by a peritectoid reaction between ß manganese and the second new phase, (. The latter phase is homogeneous at silicon contents from 16.2 to 18 at. pct and forms peritectically from the 0 phase and liquid. The eutectic reaction occurs between the ( phase and MnsSi rather than the ß phase and Mn3Si. As a result of this investigation, a modification of the manganese-rich section of the MnSi equilihrium diagram is proposed. The binary diagram of Mn-Si, according to Hansen,' Fig. 1, exhibits in the low-silicon region (below 24 at. pct Si) a peritectic transformation at 900°C of 0 manganese + Mn3Si to a manganese as determined by R. Vogel and H. Bedarff2 as well as a thermal effect at 980°C between 16.2 and 22.6 at. pct Si reported by the same authors. The nature of the latter transformation was unknown. K. Amark, B. Boren, and A. westgren3 reported indications that possibly four more phases existed in the range of 10 to 27 at. pct Si. The present investigation deals with the phase relations in the range of 2.1 to 17.7 at. pct Si. A few spot checks were conducted up to 23.84 at. pct Si. EXPERIMENTAL PROCEDURE Small experimental heats were prepared by induction melting in a vacuum furnace using argon as a protective atmosphere. The crucible was of commercial-quality magnesia. The furnace charge consisted of silicon metal and dehydrogenated electrolytic manganese. The typical analysis for these materials is shown in Table I. The molten alloy was tapped into 2-in.-square, 7-in.-long ingots. After visual inspection, a small quantity of alloy in the middle portion of the ingot was separated for use in this investigation.

Jan 1, 1964

By R. H. Swallow, George Hess

Aerial photography was once a crude, uncertain tool. Today it is a precision mapping instrument which saves important time and money for strip mining and other industry. Aerial photography began in the boxkite days of aviation. The Army first used it for rough reconnaissance photographs. Then, in the early Twenties, industry began to use aerial photographs of their plants and facilities for advertising or annual reports. The quality of these pictures was not very good by today's standards, but this work began the development of better cameras, better lenses, better photographic techniques.

Jan 1, 1949

By H. V. Welch

In this paper, as prepared for delivery at the Southern California regional meeting on Oct. 14, 1948, it was thought best to interpret the term "economics" in a rather broad manner and to include, in addition to the material losses and recoveries and associated monetary values (Part I), a limited discussion of the increased difficulties or the particular problem and the special requirements, as the particle sizes of the suspended particles range down from the relatively coarse to 100, to 10, to 1 micron or even to a fraction of one micron (Part II). Further, it is not quite in order to overlook entirely the community and individual health problems, although space requires the economics of this to be considered only very incompletely. Therefore, Part III, covering this phase of the subject, is very limited. This paper, then, is divided into 5 parts or headings as follows: I Losses and/or values in suspended solids. II Particle size. III Dust and fumes in community and individual living. IV Means and Procedures for dust and fume collection. V Description or examples of specific equipment in service and of the several types used for dust and fume collection. Because of the wide extent and wealth of subject material available and the space and time limitation imposed, presentation and discussion are less than originally planned. I—Losses and/or Values in Suspended Solids The weight involved in moving streams of industrial plant gases is commonly not appreciated, neither is their carrying power in the weight of solids maintained in suspension and moved with the gas stream from a point of origin or pick-up to a point of dissipation or settlement. These, however, are major weight figures; for example, in a modern iron blast furnace there may be five tons of gas for every ton of iron produced and by the time this blast furnace gas has been burned in stoves or under boilers the weight of gas discharged to atmosphere is on the order of eight times the weight of iron produced. Similarly for nonferrous metallurgy there may readily be from 10 to 20 times the weight of gases discharged to atmosphere as there is metal produced. A cement kiln in operation or a kiln in service to produce metallurgical lime may have on the order of 5 to 6 times the weight of stack gases as of clinker or lime produced, and at least the cement kiln, because of the very fine nature of its feed, is a very heavy dust producer. It may be noted that there have been two developments in progress for nearly three decades. Both are extraordinary in the industrial economics effected and in their ready availability to ever larger units of operation and their ever widening importance in industry, and both are productive of great quantities of finely divided material in furnacing. The first of these is the flotation process for ores, especially the metallics such as copper, lead, and zinc; and the second, powdered fuel combustion for power plant, industrial plants and metallurgical operations. Today, new developments, for example, flotation for the nonmetallics such as higher grade limestone for cement manufacture which requires still finer grinding and the powdered-coal-fired boilers with production ratings of over 1,000,000 lb of steam per hr, bring still more concentrated and hugely increased quantities of stack emission. Perhaps the honors for the greatest interest in the quantities and values escaping in waste furnace and equipment gases belong to the nonferrous metallurgical operations. Their record of achievement in the installation of dust and fume collection equipment, largely baghouses or Cottrell electrical precipitators, is exceeded by no other industry. Something of the magnitude and variety of equipment utilized in such recovery systems was covered by the writer in two papers presented to the Institute some 10 years ago.1,2 It is not intended to repeat the material of those articles, but it is thought that they complement this offering and should be noted. COPPER ROASTERS As the copper roasters are the first of the series of furnaces handling the copper-bearing concentrates in the usual copper smelter of today, it is in order to make them the first consideration. Multiple hearth sulphide roasters, not hard driven, often maintain their dust loss through exit gases at 3 pet or below of feed to furnace; in hard-driven or maximum-driven furnaces, exit gas losses often approximate 7 pet of charge with a ±2 pet variation for special conditions prevailing at some plants. A 5 pet loss of feed in a roaster gas exit, unless reclaimed, often makes the difference between a profit and loss operation, and in many cases substantial recovery is the very basis of dividend payments. As there is available very practical and successful equipment for the collection of the

Jan 1, 1950

By George W. Doffing

Numerous contradictory statements have been made in the past regarding the importance of the seasonal influence of demand for motor fuel on prices of oil securities. It has often been said that the time to buy oil securities is in the spring, or just prior to the heavy consuming season for gasoline. The fallacy of this argument is brought out in the following paragraphs. Seasonality of Oil-security Prices The indexes used in this paper as indicators of prices of oil securities and general industrials are those compiled by Standard Statistics Co. The oil producing and refining stock index includes 14 representative petroleum companies, while the all-industrials index is made up of 347 issues. All figures are stated as relatives, with 1926 = 100. The primary basis of the index, and one that gives a good weighting of the relative importance of the company within the industry, is the total market value of the stock issue outstanding; i.e., the market price times the number of shares outstanding. Adjustments are made for the addition or elimination of issues from the group index, for stock dividends, split-ups, stock rights, et cetera. At the present time the oil producing and refining index includes the following companies: Atlantic Refining Co., Consolidated Oil Corporation, Continental Oil Co., Gulf Oil Corporation, Humble Oil & Refining Co., Ohio Oil Co., Royal Dutch Co., Shell Union Oil Corporation, Socony-Vacuum Oil Co., Standard Oil Company of California, Standard Oil Co. (Indiana), Standard Oil Co. (New Jersey), Texas Corporation, Union Oil Company of California. In calculating the seasonal for oil-security prices several periods have been selected as indicat,ive of major changes in the industry, as follows: 1. 1918 through 1936. This gives an over-all picture of the industry during the motor-vehicle, motor-fuel era. 2. 1927 through 1936. This period includes the control stages, both voluntary and coercive. 3. 1927 to September, 1933. This is the pre-code period of control.

Jan 1, 1937

By J. Hoover Mackin

The iron ore bodies of the Iron Springs district are replacement deposits of magnetite and hematite in Jurassic limestone around the borders of three intrusions of quartz-monzonite porphyry. Production in the period 1923-1965 was about 72,000,000 tons, nearly all of which was direct-shipping ore from open pits. The intrusions are laccolithic in form; all three were emplaced at the same stratigraphic horizon, which had been a zone of decollement gliding during the Laramide orogeny. The intrusions and associated volcanic rocks are post-orogenic. There was no change in the thickness of the limestone during the metallization. Comparison of the composition of the limestone and stratigraphically equivalent replacement ore indicates that, with every million tons of iron, there were additions of 40,000 tons of silicon, 20,000 tons of magnesium, and 10,000 tons of aluminum. The ore-forming fluid was derived from the exposed porphyry. The iron was first incorporated in hydroxyl-bearing mafics, which crystallized in depth and were carried upward in the magma that formed the hypabyssal intrusions. The mafic phenocrysts decayed deuterically in the new environment, releasing iron into the interstitial fluid of a consolidating crystal mush in the interior of the intrusions. Primary tension joints, which opened in areas of late intrusive distention, served as roots through which the ore-forming fluid was drawn from the crystal mush.

Jan 1, 1968

By H. N. Eavenson

EaRly in 1917, the United States Coal & Coke Co. secured options on several tracts in Harlan County, Ky., aggregating about 19,000 acres in area, and after careful prospecting by outcrop openings and diamond drilling, completed the purchase late in July of that year. This property is situated in the eastern end of Harlan County, south of the Poor Fork of Cumberland River, and extending across Big Black Mountain to the Clover Fork of Cumberland River, a distance of about 7 mi. (11.3 kg.). It extends from the Kentucky-Virginia line westward for about 6 mi. Looney Creek, which empties into Poor Fork, crosses the property for about 4 mi. (6.4 kg.), and as several of the seams within the property outcrop along this stream, it afforded an easy, and the logical, place for development. The property is on the northern side of the geological trough formed by the uplifting of Stone Mountain, on the southern, and Pine Mountain, on the northern side; the northern boundary along Poor Fork is practically at the base of Pine Mountain. This area has been described in various geological reports. The main seam on this property is the one known variously as the "C," Benham, Keokee, Taggart, and Roda; it is also called, by the Kentucky Geological Survey, the Kellioka seam of the western portion of Harlan County. This seam averages, in this property, about 5 ft. (1.5 m.) in thickness, although local rolls reduce this thickness considerably over small areas, and at the extreme western end of the property the seam splits. It is usually clean, although occasionally a small parting occurs within a few inches of the bottom of the seam; it is one of the best coking and gas coals in the United States. The average analysis of this coal is given in Table 1.

Jan 1, 1922

By Joseph R. Hatch

When compared to average shale composition, average coal is enriched in sulfur and selenium, has similar amounts of arsenic, beryllium, lead, antimony and molybdenum, and is depleted in at least 26 other elements. Within a coalfield, or region, some coals are enriched (10X average shale) in silver, arsenic, cadmium, cobalt, germanium, molybdenum, nickel, lead, selenium, uranium, and zinc. Important factors controlling element distributions in coal include geochemical conditions (primarily pH) in the peat swamp, composition and depositional environment of coal roof rocks, thermal maturity (rank), nature and intensity of any epigenetic mineralization, composition of ground waters that come in contact with the coal, and degree of weathering.

Jan 1, 1983

By Rex B. McLellan, W. A. Oates, William W. Dunn

Vapor transport experiments have been carried out in order to determine the saturation solubility of carbon in cobalt and nickel with respect to graphite over a large temperature range. Some of the uncertainty existing in the thermodynamics of these systems has been removed and accurate estimates of the heat and entropy of solution of carbon in nickel and cobalt have been deduced. The relatitle partial entropies of carbon are considered to be predominantly vibrational in origin. ALTHOUGH the thermodynamic properties of solid solutions of carbon in cobalt and in nickel have been investigated previously, the results of these investigations show a marked lack of agreement amongst themselves. In this investigation simple vapor transport experiments have been undertaken in order to measure the temperature variation of the saturation solubility of carbon in nickel and cobalt with the object of removing to some degree the uncertainties in the thermodynamics of these systems. In the case of the C-Co system, early measurements of the saturation solubility of graphite in Co show results at the same temperature differing by almost an order of magnitude.1-5 Recently Schenck, Frohberg, and Jaspert6 measured the equilibrium between CH4-H2 mixtures and C-Co solid solutions at five temperatures ranging from 850° to 1050°C. Their values of the activity of carbon in the solid solution, deduced from a knowledge of the chemical potential of carbon atoms in the gas, varies linearly with composition at each temperature and the authors concluded that the solutions were Henryan. The saturation solubilities deduced from Schenck, Frohberg, and Jaspert's measurements are in good agreement with the solubility determined at 1000°C by Rao and Nicholson7 and the value at 1000°C deduced from the measurements of smith8 on the equilibrium between CO/CO2 mixtures and C-Co solutions. The object of this investigation was to check the results of Schenck, Frohberg, and Jaspert and also to extend the range of solubility data to higher temperatures. In the case of the C-Ni system, there is fairly good agreement between the values given by schaefer9 for the saturation solubility of carbon C, in nickel, the value given at 1000°C by Rao and Nicholson,7 and that deduced from Smith's8 measurements of the equilibrium between C-Ni solutions and CO/CO2 mixtures at 1000°C. The values of C, deduced from Schenck, Frohberg, and Jaspert's6 measurements of the carbon activity in nickel are also in fairly good agreement. However, there is a large discrepancy between the above set of measurements and those of Lander, Kern, and Beach," who measured the carbon solubility of nickel in equilibrium with graphite by depositing an excess of graphite on the surface of Ni-foils from a gaseous mixture and subsequently diffusing in the carbon. These results are considerably higher than those mentioned above. The determinations6 of carbon activity a, in nickel from the CH4-H2 equilibrium showed that at all the temperatures investigated, the ac-values varied linearly with concentration up to about a, = 0.6 and then began to increase with concentration much more rapidly. On the basis of auxiliary experiments in which C-Ni solutions were equilibrated with graphite, Schenck, Frohberg, and Jaspert concluded that their CH4-H2 solid equilibrations at high values of a, were spurious and a, behaved linearly with composition up to the saturation limit (a, = 1). The short linear extrapolations of Schenck, Frohberg, and Jaspert's a, data yield values of C, in good agreement with those of Lander, Kern, and Beach." The solubility data for nickel discussed here is presented in Fig. 1 in the form of plots of ln[Cc/(l - 2cc)] vs 1/T. The discrepancies mentioned are clearly seen. In this investigation a vapor transport method is used to measure C, over as wide a temperature range

Jan 1, 1969