Search Documents

By D. J. Schmatz, H. I. Aaronson, H. A. Domian

Diffusion kinetics in disordered hcp Cd-Mg alloys have been investigated by means of the Kirkendall effect and concentration-penetration curves determined with an electron-microprobe analyzer. Self-diffusion coefficients of both species were determined at the three marker compositions obtained, averaging 27.6, 46. 7, and 78.1 at. pct Mg, by means of the Darken analysis. These coefficients were then corrected for the unequal and concentration-dependent partial molar volumes of the two elements with the Balluffi analysis, and for the vacancy flux effect by the Manning analysis. The latter correction reduced the Balluffi correction produced larger changes in the self-diffusiv-ities; neither, however, produced statistically significant changes in the Do's or the H'S. The most striking result of this investigation is that at all three compositions and at all temperatures studied both the uncorrected and corrected self-difjusivities of magnesium are higher than those of cadmium. The Cd-Mg system is the first one found in which the higher melting, lower vapor pressure element diffuses more rapidly. Both an empirical correlation due to Toth and Searcy and considerations of the atomic mechanism of diffusion indicate that this anomaly is probably due to a comparatively low value of the activation energy required for a magnesium atom and a vacancy to exchange sites, perhaps occasioned by the higher compressibility of magnesium atoms. KIRKENDALL effect studies have been previously reported for only two hcp solid solutions: the E phase of the Zn-Cu system1 and the a phase of the Cd-Hg system.' In neither investigation were the marker-movement studies supplemented with the concentration-penetration curve determinations necessary to evaluate self-diffusivities by means of the atano and the Darken analyses. The present program was undertaken to obtain both types of data on a hexagonal solid solution in order to provide more detailed information relevant to the mechanism of diffusion in this type of lattice. The Cd-Mg system was chosen for this study because the disordered solid solution extends across the entire phase diagram at temperatures above 253"c5 and the substantial difference in the melting points of the component pure metals promised that marker movements would occur at reasonably rapid rates should the diffusivities of the two species be as unequal as might be anticipated. The experimental convenience of the relatively low melting points of cad-miun and magnesium and the availability of extensive and accurate activity data6 (required for application of the Darken analysis) were additional reasons for selecting this alloy system. Since the anisotropy of diffusion is not large in either pure cadmium7 or pure magnesium,' the diffusion couples were prepared from polycrystalline components. The presence of a well-defined texture in the couples—the c axis of individual crystals tended to be normal to the diffusion direction— however, provides a fair degree of crystallographic definition to the data obtained. The principal (and entirely unexpected) finding of this investigation, that magnesium, the high-melting low-vapor pressure element, diffuses more rapidly than cadmium, in contradiction to a broad range of results in fcc and bcc alloys, as well as in the previously studied hcp alloys,172 makes the self-diffusivity determinations of immediate interest in understanding the origin of this anomalous result. EXPERIMENTAL PROCEDURE The cadmium (Belmont Smelting and Refining Co.) and magnesium (Dow Chemical Co.) used in this study were both of 99.99 pct purity. Alloys containing 51.0 and 65.6 at. pct Mg were prepared from these materials by melting under a MgC12-base flux in a high-purity graphite crucible. These alloys were subsequently hot-worked and then homogenized in a helium atmosphere at temperatures close to their solidus points. Sandwich-type diffusion couples of the type g/d/g were prepared from the pure metals by solid-state diffusion. Two-piece alloy couples of Mg/65.5 at. pct Mg (Mg/gCd) and Cd/51.0 at. pct Mg (Cd/CdMg) were welded by a liquation technique. The individual components of both types of couple were initially cylinders 1.27 cm in diam and in length; the ends of these cylinders were machined accurately flat and parallel. For both welding techniques, the pure cadmium cylinders and the alloys were chemically polished in a mixture of 40 pct ethyl alcohol, 40 pct hydrogen peroxide (30 pct conc), and 20 pct nitric acid,g while those of pure magnesium were polished in a solution of 10 pct nitric acid in ethyl alcohol.' Immediately afterwards, both metals were rinsed in freshly distilled acetone, and then in similarly purified methanol.' The Mg/Cd/g couples were assembled in a carefully cleaned stainless-steel welding fixture, in which a screw operating through a self-centering arrangement permitted a controlled pressure to be exerted upon a couple prior to welding.'' Tungsten marker wires 0.005 cm in diam were placed at the d:g interfaces of some of these couples, and imbedded in the couples during the application of pressure. As soon as a couple had been assembled, the welding fixture was inserted into a Pyrex capsule containing a packet of zirconium chips at each end. The capsule

Jan 1, 1967

By Nestor Torres-Acuña, Fathi Habashi

Metallic copper of purity equal to commercial electrolytic copper is deposited during the anodic dissolution of technically available white metal, Cu2S, in m acidic solution of' copper(II) sulfate as electrolyte and copper sheets as cathodes. The process may be applied on commercial scale since it has the advantage of by passing the converting and poling steps, decreasing pollution problems due to SO, and recovering the sulfur of the white metal in the elemental form. The anodic dissolution is believed to take place in three steps: The working conditions that lead to 98 pct cathodic current efficiency are: 30 gpl Cu2+ and 100 gpl H2SO4 in electrolyte, current density 1.0 amp per sq dm, and tetnperature of bath 40°C'. DURING the smelting of copper, nickel, lead, and zinc sulfide ores, large amounts of sulfur dioxide are produced. Because the release of this gas in the atmosphere causes pollution problems, many attempts were made in the past for its recovery either in liquified form or processed to sulfuric acid. Although these two forms of sulfur are the usual forms that are consumed by the chemical and metallurgical industries, their storage and transport usually raise economic problems. It was realized, long ago, that a process by which sulfur can be recovered directly in the elemental form would be most attractive. Elemental sulfur is easily stored and transported, and is readily converted to SO2, H2S, or H2SO4 when needed. Processes aimed to recover the metals from their sulfide ores, and at the same time by-product sulfur in the elemental form, were recently reviewed.' As early as 1882, Marchese2 patented a process in which a matte having the composition: Cu 15, Pb 14, Fe 41, and S 25 pct was electrolyzed. According to cohen3 the process was applied on a pilot scale by the Aktiengesellschaft fur Bergbau-, Blei-, und Zinkhiitten-betriebe at Stolberg, Rheinland, Germany. The process was unsuccessful, however, owing to the contamination of the electrolyte during electrolysis. Studies in this field were reported by Bernfeld4 and Egli.5 Borchers et a1.6-8 developed the process further by using white metal (Cu 78.2 pct, S 19.6 pct) instead of the matte, and a pilot plant was operated by the Mansfeldschen Kupferschiefer Co. at Eisleben, German~.~ It appears, however, that the process never went into commercial operation. Further studies in this direction were carried out by Russian workers.10-23 The International Nickel Co. of Canada erected a pilot plant at Port Colborne in 1951 to apply the process to nickel matte which is essentially pure nickel sulfide."'- 26 Full-scale plant went into operation at the Thompson Refinery in Manitoba in 1964.27 In this method nickel sulfide matte is melted and cast into anodes analyzing 76 pct Ni and 20 pct S with small amounts of copper, cobalt, and iron. These anodes are then electrolyzed in an aqueous solution of NiS04 at pH 4. Further work on this method was reported in the literature.28-31 In this paper, experiments on the anodic dissolution of white metal in aqueous copper sulfate solution are reported. EXPERIMENTAL White metal, Table I, obtained from The Anaconda Co., was cast in form of anodes 10 by 7.5 by 1 cm, Fig. 1. The anodes are mechanically strong and do not break easily; when polished they gave a shiny gray metallic appearance. From the chemical composition shown in Table I, it can be seen that the atomic ratio Cu:S corresponds approximately to the formula CU2.06S. The copper in excess to the formula Cu2S is most probably present as a separate phase since metallic copper could be seen under the microscope, Fig. 2. Fig. 3 shows the X-ray diffraction pattern of white metal which matches fairly well with that of reagent-grade Cu2S.

Jan 1, 1969

By Paul M. Tyler

MILITARY power stems from industrial power and industrial power in turn depends predominantly upon an ample and assured supply of mineral raw materials. It thus becomes the duty of mineral economists to collate the vast array of data and logical deductions in order to reach an unemotional judgment as to the ability of the Soviet economy to withstand the strain of prolonged military action on the modern scale. Russian publications, reports: and official speeches have been laboriously screened and analyzed. Since these are the sources of information for the lower echelons of the Soviet industrial organization itself, they carry factual data that can be pieced together to show the present-day pattern. Apparent contradictions and obvious distortions or omissions can often be rationalized on the basis of observations made by foreign engineers and consultants during the 1930'5 and by checking against the technical literature published before even so-called technical articles were riddled by bombastic and presumptuous claims.

Jan 6, 1951

By A. L. Baxley

An Untapped Energy Resource As much as 20 billion cubic feet of natural gas per day are flared from remote oil fields for lack of a commercially viable means of capturing, transporting, and marketing such gas. The magnitude of these gas flares can be put into perspective from an early satellite photograph (Fig. 1) which shows lights from the major cities of Russia and Eastern Europe dwarfed by the natural gas being flared in the Persian Gulf. Together, these wasted resources contain the energy equivalent of about one-half of the gasoline consumption in the United States today (Fig. 2). Additional trillions of cubic feet of natural gas are "shut-in" because of no economically viable means of commercial recovery. Methanol and liquified natural gas (LNG) are the only two practical fuel products which can be produced economically from these gas supplies. Many of these gas supplies are less than 500 million cubic feet of gas per day, making an LNG facility uneconomic. In contrast, barge-mounted methanol plants can economically convert billions of cubic feet of gas per day into safe, clean-burning methanol. The methanol approach offers the only economical route to transform vast, known reserves of natural gas into a highly versatile primary liquid fuel. Methanol Barges: An Innovative Solution The barges will be towed to suitable offshore and upriver locations such as Alaska, South America, Africa, Southeast Asia, Australia, New Zealand, and the South Pacific Islands, as well as fields in the Persian Gulf and Mediterranean Sea. At the offshore production site, a barge will be anchored by a single point mooring buoy that will also serve as an entry point for natural gas feedstock and an offloading point for methanol (Fig. 3). At some sites the barge would be beached. Each barge will produce methanol and store it in internal tanks with a capacity of 18 million gallons. The methanol will be offloaded into conventional tankers and safely transported directly to market. Unlike LNG, methanol requires neither specially built carriers nor specially built receiving terminals. Once a particular gas field has been exhausted, the barge will be towed to another location to continue production. Each barge will measure 320 by 500 ft, approximately the size of four football fields, and will have the capacity to produce 1 million gallons or 2800 metric tons of methanol per day, from approximately 100 million cubic feet of natural gas per day (Fig. 4). The barges will use the highly successful "low- pressure" design developed by the Lurgi Company of Germany, a process proven in land-based methanol plants throughout the world during the last ten years. The decision to use Lurgi technology for "sea-trans- portable" methanol plants was based on the higher efficiency and greater operability of the technology compared to other commercially proven processes. The conversion plant will be designed to accept a wide variety of feed gas compositions, and will produce chemical-grade methanol for the broadest market base (Fig. 5). To minimize costs and construction time, the barge-mounted plants will be built in the high technology environment of a domestic or foreign shipyard. Selection of the construction site for each barge will be dictated by the location of the production site and by the relative construction costs. A number of shipyards have the capacity to build several barges per year. The detailed marine engineering to integrate the design of the processing plant with the floating platform can be performed by numerous major engineering companies around the world. Production Economics The barge-mounted plant concept not only assures large volumes of methanol, but it also keeps the overall production cost low by minimizing construction cost and providing access to low cost natural gas feedstock with no alternative or a negative value. Together, these advantages make the barge-mounted methanol plants economical today. The cost structure of a new barge-mounted methanol plant differs from that of existing methanol producers around the world (Fig. 6). For example, if a U.S. Gulf Coast producer is paying $4.70/MMBtu in 1985 for natural gas, the barge plant could afford to pay about $1.6O/MMBtu for gas and be able to deliver methanol to the Gulf Coast at the same price. At some future date such as 1990, a gas cost of $6.70/MMBtu for a domestic producer would have cost parity with about $3.60/MMBtu gas cost for the barge plant. In many foreign markets, feedstocks other than natural gas are used for methanol production (Fig. 7). For example, most of Japan's capacity is based on LNG while Western Europe uses residual oil or naptha. Because these feedstocks are substantially more ex- pensive than natural gas used by U.S. producers, the barge plants will compete even more favorably in these foreign markets. As crude oil prices rise, the value of methanol in each of these markets will increase. However, the hierarchy of methanol values in these markets should remain unchanged. Furthermore, the cost advantage for using methanol in these markets will improve as world energy costs increase since the value of remote gas should not escalate significantly.

Jan 1, 1982

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By Gilbert L. Eggert

The effects of reactor irradiation on age hardening in a Cu-2 wt pct Be alloy have been investigated in two neutron-energy ranges. During some of the irradiations, specimens were exposed to high-energy fission neutrons which passed through a boron-10 shield; during other bombardments, the boron-10 was omitted and specimens were irradiated in a reactor thermal column, or the fuel configuration was modified to increase the thermal-neutron flux at a location in the core. Differences in length, X-ray diffraction angle, and hardness indicated that low-energy neutron irradiation made a small contribution to changes in the measured properties. The influence of defects generated by knock-om with less than the Brinkman critical energy or by prompt (n,y) recoil is suggested as the cause of this effect. EXPERIMENTS designed to test the effects of reactor irradiation on the properties of age-hardening alloys have to the present time employed fluxes un-differentiated according to neutron energy. Billing-ton and Siegell in 1950 were the first to perform such an experiment and to compare the results with those obtained by thermal aging. These authors concluded that precipitation in a Cu-2 wt pct Be alloy was not enhanced by the radiation. However, 4 years later, Murray and Taylor,2 working with specimens of the same Cu-2 wt pct Be alloy, reported that an increase in density, hardness, and resistivity which followed reactor irradiation resembled changes associated with thermal aging at about 100°C. (It should be noted that these authors reported that higher aging temperatures caused a decrease in resistivity.) cupp3 reported hardness results similar to those of Murray and Taylor. Koppenaal4 showed that irradiation-enhanced precipitation and irradiation defect hardening were not simply additive but that they acted separately in an irradiated alloy. Kernohan et a1.,5 working with Ni-Be, offered evidence that beryllium was removed from solid solution by reactor irradiation and suggested that the mechanism was one of increased diffusion through the use of vacancies in the structure. piercy6 also found that more precipitate particles were formed by fission-neutron irradiation of a Cu-Co alloy which contained a small amount of particles before irradiation. He proposed that the additional particles were caused by an appreciable amount of diffusion during the final cooling of displacement spikes. The retrogression of extant precipitate particles found by Murray and Taylor2 and Boltax7 as well as piercy6 indicated that nuclei were dissolved within a high-energy spike region and, upon resolidification of the perturbed volume, new nuclei precipitate and grow by enhanced diffusion. Bleiberg et al.' and Konobeevski et al.' explained phase changes obtained by irradiating fissionable alloys in terms of retrogression and re-precipitation in regions of high-energy spikes. Parsons and Balluffi10 used electron microscopy to verify that crystallization did indeed occur in displacement spikes which were formed in amorphous germanium by fast-neutron irradiation. The concept that low-energy neutron irradiation might cause structure-sensitive property changes in semiconductors by atomic recoil associated with the (n, y) reaction was first proposed by Schweinler" and walker." This thesis was tested by Cleland and crawford" and found to be valid. Coltman et al.14 exposed a variety of pure metals to thermal-neutron irradiation at cryogenic temperatures and attributed the resulting resistivity changes to the action of defects created by (n, y) recoil. The present work was undertaken to extend the concepts of Schweinler," walker," and Coltman et al.I4 to the case of an age-hardening alloy and to determine whether or not the action of defects produced by thermal-neutron irradiation would en-hance age hardening. EXPERIMENTAL PROCEDURE Omeea West Reactor Irradiations.* Thermal-

Jan 1, 1965

By M. R. Tek, K. H. Coats, D. L. Katz

The performance of a gas reservoir su,bject to water drive is often affected by interference due to gas procluction or injection in neighboring reservoirs adjacent to a common aquifer. Field data available on production-pressure behavior of several reservoirs indicate that prediction of reservoir performence must include the effects due to mutual interference. A method developed to predict the performance of two or more interfering gas reservoirs, subject to specified production-iniection .rchedule.s, is presented. The method involves the comhinatiorz of the theory of unsteady-state water movernent with appropriate meterial balance consideration.s. The procedure which extends M. Mortada's treatment for interfering oil reservoirs makes use of his dimen-.sionless pressure drop quantities. prevented graphically in the literature. In order to evaluale the predictive accuracy and practical field applicability of the theory, the method has been applied to analyze the performance of two actual gas reservoirs in mutual interference. The calculations were performed on an IBA4 704 computer. The predicted performances were alro calcltlated with the interference effects ignored. The results show that considerably better agreement between calculated and observed behavior ic. obtained when the interference effects are included. INTRODUCTION Fluid communication between any number of oil or gas reservoirs adjacent to a common aquifer results in mutual interference effects on their production-pressure behavior. The theory, application and interpretation of pressure build-up behavior of oil wells, drawdown tests on oil or gas-producing formations and behavior of several storage reservoirs indicate ample experimental evidence of mutual interference. A method developed to compute the behavior of interfering oil reservoirs was published several years ago by Mortada.4 Studies conducted during the recent years on underground storage of natural gas clearly indicated the need for extending Mortada's work to the case of interfering gas reservoirs. The adoption of appropriate material balance equations in conjunction with the unsteady-state pressure interference theory yields pressure-explicit equations. Their solution, their application to a specific case history and an over-all evaluation of the developed method through the comparison of predicted and observed field performances were the main objectives of this study. DEVELOPMENT OF MATHEMATICAL RELATIONS The diffusivity Eq. 1 governs planar, radial, unsteady-state compressible liquid flow through a porous medium. ?p/?r2+1/r ?p/?r=µFc/k ?p/?t (1) The 1iterature1,2,3 contains derivations and solutions of

By M. J. Mullikin, J. B. Conway

Equations capable of representing combined first -and second-stage creep behavior include the Andrade, Cottrell-Aytekin, Garofalo, and de Lacombe equations along with a third-degree polynomial in t1/3. Employing some recent high- temperature creep data for arc-cast tungsten the effectiveness of these expressions was evaluated. It was found that, in this instance, the most accurate representations were afforded by the third-degree polynomial in t1/3 and the de Lacombe equation. Also noted was the fact that the Andrade equation gave results just slightly inferior to those obtained with the third-degree polynomial, definitely better than those due to the Cottrell-Aytekin equation, and slightly superior to those furnished by the Garofalo equation. EXPRESSIONS designed to describe combined first -and second-stage creep behavior must possess certain specific characteristics. At time zero the equation must reduce to a strain value corresponding to the instantaneous deformation on loading. Then in the early moments following load application transient-creep behavior must be described to reflect a creep rate which constantly decreases with time. And finally at larger time values linear (or at least nearly linear) strain-time behavior must be accounted for to yield the steady state or minimum creep rate. Some equations, such as the one based on the parabolic creep law, yield fairly satisfactory results in transient analyses but are not effective at all when combined first- and second-stage data are to be analyzed. Other equations give equally accurate results in both instances although in general the complexity of the equation is slightly increased. For example the Andrade1 equation: has found fairly general application in expressing first-stage creep behavior. Furthermore the contribution of the exponential term becomes more and more prominent as the time increases and causes this equation to exhibit a point of inflection at large values of time. With a proper selection of equation constants the curve can be made fairly flat in the region of the inflection point indicating a desirable equation form for combined first- and second-stage creep analysis. Another equation form with the proper characteristic is that of Cottrell and Aytekin:2 e =a +bt1/3 +ct [2] Obviously as time increases the first derivative of this expression approaches a constant value to suggest application to combined first- and second-stage creep analysis. Similarly a third-degree polynomial in t1/3: e -a + bt1/3 + ct2/3 +dt [3] has the same characteristics. Expressions of this type have been shown3 to be very effective in the analysis of transient-creep behavior and the fact that the first derivative has the same characteristic as Eq. [2] suggests use in the combined analysis.

Jan 1, 1967

THE first session of the Institute was held on Tuesday evening, September 16th, in the William Molson Hall, of McGill University, Dr. T. Sterry Hunt, Chairman of the Local Committee of Arrangements, in the chair. Dr. Hunt introduced Monsieur S. Rivard, Mayor of Montreal, who spoke as follows : GENTLEMEN: We welcome you with pleasure to our city, and we are proud to find that you have deemed it worthy of your visit. I understand that your association was founded in 1871 with some thirty courageous members, and that so valuable has it been esteemed, and so attractive was it found, that nearly one thousand have now enrolled their names as members and associates. But we must regard your profession as dating back to the stone age and mingling therewith ; how remote that is none of us can tell. Much of civilization is due to the discovery of metals, and the magnitude of our works to their widespread abundance. If you have not accomplished what the alchemists aimed at, which was to turn the ruder materials into gold, you manage, by your subtle skill, to turn stones into gold value. Europe has long since been-dug into and perforated with shafts and galleries in search of metals, and great wealth, and power, and comfort have arisen there-from ; but by an increase of knowledge, and more than European enterprise and energy, America is following rapidly in the race, and by means of natural advantages of a geological character has out-stripped the Old World. We are pleased to see you, gentlemen, as an evidence of the unity of this continent. Maps may have various delineations, but the veins and arteries of commerce and the nerves of science knit all together into one social organism with the same vital functions. We live here on the margin of the world, and can claim but a modest share in. the great works of modern times, but such as we have that can interest you we gladly offer for your observation.' Our Victoria Bridge may he considered appropriate, for without mining engineers to precede the civil and mechanical, no bridge would be there to-day. In truth, the same may be said of all works of metal, and of all that are executed by tools and machinery made of metal. The Mont

Jan 1, 1880

By ALFRED KAUFFMAN

NO matter what position we hold, workman, foreman, superintendent, manager, president, or what not, let us fail to give or to make good products, then see how quickly we'll be called to account for- our work by the buying public. The waves of progress taught us that millions were wasted in unnecessary strikes-we also learned that many losses were due to neglect on the part of manufacturers to give the same consideration and attention to the human element of their factory as they gave to their machinery. The employees learned also that the employer was their agent who found purchasers for the product of their labor. So between the two we learned that many years of labor were needed in order for a worker to recover his wasted savings, or for the manu¬facturer to replenish his loss. Treat 'em rough, and tell 'em nothing, was not very far from the true relationship between management and employees in manufacturing plants in the early days. Today just exactly the opposite views are held by executives whose function is the handling of employees. Men today want to know what it is all about. They are intelligent enough to comprehend the facts, and to use them constructively, and it is good business to give them the information.

Jan 1, 1929

By Jack M. Swales

Kermac Potash Co., the newest American entry in a rapidly expanding industry, has come on the scene with notable variations in conventional shaft-sinking and mining techniques. Located in the famed potash producing district east of Carlsbad, N. Mex., Kermac started up its mine in November, 1965, to supply ore to the company's 500,000-tpy potash crystallization refinery. In so doing, the company (1) drilled the first large diameter mine shaft in the potash industry and (2) has employed new continuous miners especially adapted for use in thin potash beds. REACHING THE ORE ZONE In its initial mine planning, Kermac, a partnership owned jointly by Kerr-McGee Corp. and the National Farmers Union Development Corp., considered it imperative that the shafts be sunk and equipped as soon as possible and that the mine be developed sufficiently to insure a constant ore feed to the mill when the unit was placed on stream. After examining the alternative sinking techniques available to it, the company decided to accept a proposal by Big Hole Drillers, Inc., to drill the shaft from the surface through various formations of sandstones, siltstone, shales, anhydrite, limestones, dolomite and salts to the potash ore zone.

Jan 12, 1966

By F. Hass, N. W. Lord

This paper gives the results of experiments conducted in the metallurgical laboratory of the Ohio State University with the objects of determining: First, the calorific powers of a number of coals in general use in Ohio; and second, how far ordinary analytical methods could be used as a basis for computing these values. Incidentally a test of the performance of the calorimeter was involved. The chemical work has been carried on in the department for some time, so that the whole investigation has extended over three or four years. The Mahler calorimeter was purchased from L. Golaz in Paris, and is practically identical with the one described and figured by Mahler in his monograph "Contribution a l'Etude des Combustibles," from the Bulletin de la Société d' Encouragement pour l'lndustrie Nationale. A figure and description is also given by William Kent in The Mineral Industry for 1892, page 97. There were furnished with the instrument three thermometers covering a range of from 7°.5 C. to 31° C. Thermometer "A" (17°.5 to 31°) was carefully calibrated by reading the ends of a thread of mercury in sixteen positions covering the whole scale, supplementing this by readings of longer threads and deducing the errors of scale by the method published by Prof. Holman in the Technology Quarterly of September, 1887. The maximum error of a single reading was found to be 0°.0042 C. Thermometer "B" (13° to 25°) was compared directly with " A " over the scale common to both, and a variation was found of 0°.0145 C. for 7°.5 (or 0°.002 for l°) of the scale. Thermometer " C" ('7°.5 to 19°.0) was omitted from the cornparison, as it was rarely used, being only required where measurements were made at low temperatures. From the

Jan 1, 1898

By H. Vincent Wallace

ALTHOUGH it is universally accepted that free oxygen is A necessary in a cyanide solution for the dissolution of gold and silver-in accordance with Elsner's equation that 2Au + 4KCN + 0 + H20 = 2KAu (CN), + 2KOH- little has been written and insufficient attention paid to the drop in extraction due apparently to loss of dissolved oxygen in mill solutions. Aeration or oxygenation of cyanide solutions has been more or less successfully accomplished by various types of agitators such as the Dorr (with or without air lifts), Pachuca tanks and more recently "Turbo-mixers" and Denver "Super- agitators"; also by the introduction of chemical oxidizing agents such as Solozone (Na,O,) . At the Wright-Hargreaves and other mines in the Kirkland Lake camp, the introduction of this reagent at the rate of about 1.25 oz. per ton of ore applied to the feed of the ball mills has certainly been beneficial.

Jan 1, 1932

By Vsevolod Krivobok

THE re-crystallization of metals has been the subject of much scientific investigation, some of which has resulted in a better understanding of this extremely important and interesting phenomenon. Unfortunately, while many have propounded theories of re-crystallization, but a few have presented experimental evidence as to how it takes place. If this can be determined the question, why re-crystallization occurs, may be answered more definitely. Re-crystallization in single phase metals consists of a complete rearrangement and re-sizing of the grains, of which the structure is composed, while the type of structure remains the same. That is to say, if the structure before re-crystallization is composed of a number of polyhedral grains of different shape and size, a particular spot after re-crystallization will be seen to consist of grains in no way different from the original except in size and shape. The re-crystallized grains may be smaller or larger, depending on the treatment received; and, while the re-crystallization may be brought about by means of heat treatment only in passing through a critical range, yet it is common knowledge that single phase metals subjected to cold working are possessed of a tendency toward re-crystallization, even if the heating does not reach critical range. The study of re-crystallization would, of course, be much easier if we had single crystals of any metal as the original material with which to study the phenomenon of re-crystallization, since it would permit the observation of structural changes at what amounts to enormous magnification, by changing the scale of the specimen. In metals of more normal grain size the crystal boundaries introduce complications, but the process, it may be assumed, is essentially the same. Such an opportunity

Jan 2, 1926

By N. Parlee, V. C. Kashyap

The solubilities of nitrogen in liquid iron and liquid Fe-Ni, Fe-Mo, Fe-V, and Fe-Mo-V alloys were measured by the Sieverts method. Measurements were made at 1600° to 1800°C on binary alloys up to 20 pet Ni, 10 pet V, 10 pet Mo; and on ternary alloys containing 0 to 3 pet V with 0 to 5 pet Mo. The results on liquid iron confirm that Sieverts' law is obeyed in the range 50 to 750 mm pressure. The measured solubilities and their temperature coefficients are in general agreement with other modern authors. The logarithms of the activity coefficients of nitrogen in the binaries are approximately linear functions of the pet of alloying element. A method suggested by Wagner, Chipman, and others for predicting gas solubilities in complex alloys from solubility data on binaries was applied to the Fe-Mo-V alloys. Reasonably good agreement was obtained between calculated and experimental solubilities. NITROGEN'S solubility in liquid iron has been studied by a number of investigators. It is reasonably well established that the solubility of nitrogen follows Sieverts' law at least up to 1 atm partial pressure and that the solubility increases gradually with temperature. The solubility of nitrogen in Fe-X binary liquid systems has been investigated in only a few cases. Only the systems Fe-Cr,3-5, 7 Fe-V,3 Fe-Mn,3, 5 Fe-Ni,3, 5 Fe-Si,B, H Fe-C, L, H and Fe-P4 appear to have received any study. The only work on liquid Fe-V was done by Brick and Creevy.3 This was limited to 13.5 pet and 26.5 pet V, but no exact temperatures were recorded. No work whatsoever appears to have been done on liquid Fe-Mo alloys and even work on Fe-Ni alloys is rather scant. The work on liquid ternary systems is still more limited, and the only publication available appears to be that of Wentrup and Reif,7 who studied the Fe-Cr-Mn and Fe-Cr-Ni alloys. Rassbach, Saunders, and Harbrecht17 have reported work on the solubility of nitrogen in stainless steel but this was not a systematic study of any particular system. Commercial alloys usually contain several alloying elements. Thus, it often becomes important to be able to predict the nitrogen solubility in systems containing two or more added elements without the necessity of making measurements. Wagner,14 Chipman," Darken and Gurry," and Morris and Buehl 14 have suggested means by which this may be accomplished, and Langenberg14 has recently applied one of these methods to nitrogen solubility in complex liquid alloys. This paper reports the results of nitrogen solubility determinations on Fe-Ni, Fe-Mo, Fe-V, and Fe-Mo-V alloys and compares calculated and experimental solubilities in the ternary alloy. Attempted measurements on Fe-Cr alloys were not successful by the experimental method employed. Experimental Method The general method of solubility measurement was that of Sieverts.' The apparatus and procedure were essentially the same as used by Liang, Bever, and Floe."' The equipment consisted of a small vacuum furnace heated by a 6 kw induction unit, gas measuring apparatus, and a gas purification train. The crucibles used were Norton Alundum with alumina sand around them for insulation. The crucibles were charged with 100 to 200 g of material, about 180 g or nearly filling the crucible being found most satisfactory. Hot volumes were determined with argon and ranged from 95 to 130 cu cm (stp). Temperature measurements were made with a Leeds and Northrup optical pyrometer which was calibrated periodically against the melting point of iron in the same apparatus."-'* Good quality nitrogen, hydrogen, and argon gases were further purified and dried in standard purification trains. The sources of the high purity iron and other alloying elements used were as follows:

Jan 1, 1959

By G. Thodos, R. B. Grieves

A method has been developed for the accurate calculation of the cricondentberm and cricondenbar temperatures of multicomponent hydrocarbon mixtures of known composition. The mixtures may contain any number of components including paraffins and isoparaffins, olefins, acetylenes, naphthenes and aromatics. This approach is based upon the mole fraction of the low-boiling component in the mixture and graphically presents the ratios of the cricondentherm and cricondenbar temperatures to the pseudocritical temperature as {unctions of a boiling-point parameter. The only requirements are the critical temperature, normal boiling point and the approximate vapor pressure behavior of each component. For mixtures of more than two constituents a stepwise calculation procedure is necessary where the pseudocritical temperature is based upon the critical temperature of the pure low-boiling component and upon the actual cricondentherm or cricondenbar temperature of the mixture of all the remaining higher-boiling components. From an analysis of 22 binary systems (123 compositionsl, the average deviation of calculated cricondentherm temperatures from reported values is 0.87 per cent, based on degrees Rankine; and for 10 multicomponent mixtures containing from three to six components, the average deviation is 0.98 per cent. From an analysis of 18 binary systems (104 compositions) the average deviation of calculated cricondenbar temperatures from reported values is 0. 79 per cent; and for 15 multicomponent mixtures, 1.47 per cent. Equations, derived from the graphical relationships, are presented which enable rapid calculations for both binary and multicomponent systems. INTRODUCTION With the increasing tendency towards the use of high pressure processes, the need for an accurate method of calculation of the properties of a multicomponent hydrocarbon mixture in the critical region is becoming more essential. Critical region phase relations are also significant in gas condensate reservoirs, for which a knowledge of the fluid phase boundaries and regions of retrograde condensation make it possible to evaluate optimum operating conditions. The possibility of liquefaction in the underground structure may be established, and information on the feasibility of the use of repressurizing may be determined. A typical phase diagram for a multicomponent hydrocarbon mixture is presented as Fig. 1. This figure also shows the regions of retrograde behavior encountered by following lines AB and AC. If accurate methods of calculating the temperatures and pressures at the critical, cricondentherm (maximum temperature) and cricondenbar (maximum pressure) points of multicomponent hydrocarbon mixtures of known composition were available, it would be possible to estimate closely the entire phase diagram of any mixture. Several methods have been presented in the literature for the estimation of the critical temperatures and pressures of multicomponent mixtures containing all types of hydrocarbons and including the fixed gases.4-8,21 Considering the cricondentherm and cricondenbar points, the work is more limited. Etter and Kay5 have developed rather complex equations for

By E. S. Wheeler

The rapid increase in the use of monel metal and malleable nickel in the form of sheet, rod and tube has resulted in a similar increase in the demand for these metals in the form of castings. These castings range in size from small valves and pipe fittings weighing a few ounces to large centrifugal pumps, gate valves and marine propellers, some of the last weighing as much as 24,000 lb. A group of such castings is shown in Fig. 1. A large nickel agitator is shown in Fig. 2. Monel metal castings are widely used in accessories for steam power plants and in a variety of chemical plant equipment where the corrosion resistance, high strength and toughness characteristic of this metal render it particularly valuable. Nickel castings find extensive use in the construction of corrosion-resistant apparatus, and are often used in conjunction with wrought nickel sheet and tube in the fabrication of equipment for handling a variety of chemical and food products, particularly dairy products. In response to this demand for castings, numerous foundries have undertaken the production of castings of these metals and have met with varying degrees of success. The successful production of castings of monel metal and nickel requires careful attention to molding practice, proper melting equipment

Jan 1, 1930

By Sherwin F. Kelly

NEW trend in geophysics has been uncovered in these depression years, made evident through the thinning cloak of commercial activity, which, in better times, would have completely obscured it. I refer to the increasing use of these methods for geological investigations by federal and state geological surveys. This is a trend that has been gathering momentum not alone in the United States, but abroad as well. Thus, in Poland, the Geological Survey has been playing an increasing role in geophysical work since 1927, and now has- its own geophysical department. The government petroleum producing organization of Argentina has its Geophysical Commission; Brasil boasts a completely equipped geophysical department in its Mineral Production Service; the government of Chile has contracted with commercial companies for geophysical surveys; Peru is planning an intensive program of geophysical prospecting in its petroliferous regions; and Canada has, for several years, cooperated with

Jan 1, 1935

By James E. York

AT a meeting of the American Society for Testing Materials at Atlantic City, June, 1908, Dr.. C. B. Dudley, in his presidential address,' showed the vital necessity of not only making a steel rail as good as in the past, but of making it considerably better in order to meet the present and prospective require¬ments of railroads. Doctor Dudley requested the co-operation of all who from personal experience could give information that would result in bringing about the production of a steel rail that could be relied upon to meet the present requirements. I have had considerable experience in the practical manufacture of steel of almost every grade, during the past 40 years, and I shall suggest changes that will bring about the results desired. Doctor Dudley has had a long experience as chemical and metallurgical expert for the Pennsylvania railroad, but he frankly admits that up to the present time both he and other metallurgical experts lack the practical knowledge of steel-making that is necessary to state correctly the reasons for the unreliability of the steel rails now produced. The necessity is self-evident for more positive practical knowledge on the part of these experts of what is possible and what is impossible regarding the practical manufacturing of steel rails from the ingot to the, finished product. Chemical knowledge in steel-making is far in advance of what it was years ago, and might be said to cover every requirement (in that department) for producing reliable steel. The study of the metallography of steel has been of great value, also the physical testing of steel, but this knowledge will only de-

May 1, 1909