Search Documents

By Charles J. McMahon

In a recent paper, Floreen and Hayden report that additions of the noble metals iridium, rhodium, ruthenium, and platinum to Fe-C alloys containing 0.03 to 0.08 wt pct C act to significantly reduce the ductile-to-brittle transition temperature in a notched-bar impact test. They compare these results with the similar, well-known effects of nickel and manganese additions, and they note that this supports the hypothesis that addition of austenite stabilizers enhances notch toughness. Although not attempting to offer an explanation for this, they suggest that it might be found in an alteration of the bonding characteristics of the bcc lattice of iron by additions of elements which tend to stabilize the fcc lattice. While this suggestion appears to have some merit, it should perhaps be held in abeyance until two more likely possibilities have been explored. It is now fairly clear that the beneficial effect of manganese derives from its ability to promote a globular carbide morphology instead of the platelike form found in grain boundaries and pearlite patches in Fe-C al10~s.' Previous work14 has also shown that cleavage fracture in Fe-C alloys of the type tested by Floreen and Hayden originates almost exclusively in the cracking of cementite platelets, and that the ductile-brittle transition temperature is very sensitive to the volume density and size of these carbides. Treatments which lead to development of nonlamellar carbides or fine dispersions of carbides, such as quenching and tempering or appropriate alloy additions, promote toughness by removing the primary mode of cleavage initiation. The effectiveness of manganese in this regard has long been known. Nickel appears to behave in a similar manner, though the effect is perhaps not as dramatic as with manganese.15 However, nickel additions do lead to a definite refinement of ferrite grain size following a given transformation heat treatment, and this in itself acts to greatly enhance notch toughness.'' (The grain sizes of the various heats tested by Floreen and Hayden were not reported, so it is not known how much influence this factor exerted in their results.) In conclusion, it is suggested that one should consider the well-established effects of alloying elements on carbide morphology and ferrite grain size before resorting to more complex possibilities, such as modification of interatomic bonding.

Jan 1, 1969

By Frank R. Van Horn

In the summer of 1908, R. B. Cochran, Superintendent of the Compania Metalurgica Mexicana at Sierra Mojada, Mexico, presented to the Department of Geology and Mineralogy at Case School of Applied Science an interesting series of silver-, copper-, and lead-ores from the Veta Rica mine. These ores contained several interesting minerals which were associated in a somewhat peculiar manner, so that I was impelled to make a closer study of their occurrence. The investigation has brought out several new facts concerning the geology of the district and the geological occurrence of the ores, and therefore has seemed worthy of record. Two papers have been published previously about the region, one by Chisml in 1887, and the other by Malcolmson² in 1902. These articles, however, treat of the district more from the stand-point of the metallurgist and mining engineer, and not much attention is devoted to its mineralogy and economic geology. 11. Geographical Location of the District. The Sierra Mojada is situated in the extreme western part of the State of Coahuila, near the Chihuahua boundary. It is reached best via the Mexican Central railroad from El Paso, Tex., to Escalon, Chihuahua, a distance of 494 miles. From this point, a branch line, the Mexican Northern railroad, runs 78 miles in a NE. direction to the mines, which are its northern terminus. The railroad was built about 1890, practically on account of the Sierra Mojada mining-district.

Jan 1, 1913

By Mary Sue Coates

Characterization of the rock mass in which deep underground structures are to be located is of critical importance to the feasibility and design of the structures. The process involves areal studies, subsurface exploration and extensive testing to obtain comprehensive data on the rock units which will enclose the excavated structures. The Illinois Deep Hole Project provides an example of characterization of rock at great depth describing the types and variety of tests and studies which were utilized and the results obtained.

Jan 1, 1984

By H. M. Chance

One hundred and twenty miles of hard travel over steep ridges almost due east from Fayetteville, on the St. Louis and San Francisco Railroad, about 100 miles from Eureka Hot Springs, or 75 miles northwest from Batesville, will bring the traveller to the waters of the Buffalo Fork of the White river, in a wild, thinlysettled, heavily-timbered country, now being prospected quite actively for zinc, and known as the Buffalo or Rush Creek district. Excepting here and there a piece of bottom land, patented before the discovery of zinc, the land is unoccupied Government land, and subject to entry under the United States mineral laws. Claims are now being taken, 600 by 1500 feet, but a movement made this summer, if successful, will largely modify the position of claim-holders. A few claims are now being filed under the Placer Act on the ground that as the zinc occurs as a horizontal, sedimentary deposit, etc., it can only be properly so classified. The zinc occurs in limestone, which is at times so siliceous that

Jan 1, 1890

By J. B. Mackintosh

In a recent paper read before the Institute on this subject, Mr. G. C. Stone advances the theory that the precipitate obtained in Williams's volumetric process,* by treating the boiling nitric acid solution of a manganese salt with potassic chlorate., is not pure MnO2, but approximates more closely to the composition 10Mn02+Mn0. As the value of the process and the accuracy of our results mould depend on whether this was the fact or not, it has seemed to me, and to my associates, Messrs. Beebe and Colly, that it would be of importance to ascertain the composition of this precipitate, and to that end the following series of experiments has been undertaken. These experiments have all been based on the considerations: 1. That potassic permanganate has an oxidizing power equivalent to five atoms of oxygen for every two of manganese : K2Mn2O8 = K2O.2MnO.O5. 2. That the same amount of manganese in the state of binoxide has an oxidizing power equivalent to two atoms of oxygen : 2MnO2 = 2MnO.O2. If, then, we take a solution of permanganate of unknown strength, and reduce it to binoxide, the oxidizing power of the binoxide formed will be equal to that of two-fifths the quantity of the permanganate solution originally taken. While, if the precipitate obtained should not be binoxide, but an indefinite or definite mixture of bin- and mon- oxides, then, from its equivalent oxidizing power, we can calculate its composition. The analyses were conducted in the following manner. The amount of permanganate taken was decomposed with hydrochloric acid, and concentrated to expel the excess of water. Sufficient excess of nitric acid was now added, and the solution was boiled until all the hydrochloric acid was destroyed. The manganese was then precipitated by potassic chlorate; and, after standing some time to cool—a pre-

Jan 1, 1884

By G. Sachs, E. J. Riping

All ferrous alloys can be made brittle by straining at sufficiently low temperatures. However, the changes in mechanical properties for different ferrous materials with decreasing testing temperature do not appear to follow any universal law. In particular, complex effects of testing temperature have been observed if cold worked steels were subjected to tensile tests at low temperatures. EFFECTS OF PRESTRAINING AT A TEMPERATURE ABOVE THE TESTING TEMPERATURE ON THE FRACTURE CHARACTERISTICS‡ A considerable amount of data has been presented by a number of investigators on the fracture characteristics of various cold worked steels.' These data usually relate to a two-step procedure first used by Davidenkov,² consisting of stretching by tension to a certain strain or " prestraining" at room temperature and then completing the tensile test, or "testing" at the temperature of liquid air. On the basis of data of this type made available to date, ferrous alloys can be classified into two groups with respect to their fracture characteristics observed on testing at a low temperature after prestraining at room temperature. Very complex phenomena have been observed for all annealed steels. On the other hand, some observations indicate that steels in certain other conditions represent a fundamentally simpler relation. In considering the effect of prestraining at one temperature on the properties obtained at some lower temperature, it should be expected that any cold work reduces the ductility retained in proportion to the magnitude of the cold work. However, the test data presented to date indicate that only heat treated (quenched and tempered) steels appear to conform to this expectation, according to the very limited test data in Fig 1, presented by McAdam, Geil and Mebs. This series of tests, Fig 1, shows that the retained ductility became smaller the larger the prestrain. However, this decrease is less than the amount of prestrain or, in other words, less than the decrease in ductility at the prestraining temperature. These effects of prestraining are fundamentally identical with those observed by Bridgman3 when a steel was prestrained (in tension) under hydrostatic pressure and then subjected to a regular tension test. It appears, therefore, that the basic effect of prestraining under conditions which yield a higher ductility than the (subsequent) testing procedure, consists of gradually increasing the total ductility of the metal from the initial low value of testing to the higher value of prestraining. On the other hand, all annealed steels, if cold worked by tension at room temperature and then tested at a lower temperature, provided that some ductility is retained, showed a far more complex behavior than that discussed above. This relationship is exemplified by Fig 2, for three pearlitic steels.4,5 These particular steels were selected because of the various shapes of their ductility-prestrain curves. All three steels, and any other investigated so far, suffered a rapid decrease in retained (and consequently also in total) ductility when subjected to small pre-strains. Then, after exceeding a certain prestrain it was generally observed that the ductility recovered.* This rather complex behavior of annealed steels may be tentatively correlated with the presence of stretcher strains at small restrains. Heat treated steels do not exhibit stretcher strains. This fact might possibly explain their simpler prestrain-retained ductility relationship. The destructive effect of these stretcher strains may possibly be associated with the presence of triaxiality, which may occur in any highly non-uniform stress and strain state (and which is retained as residual stress after unloading). Even a small degree of triaxiality may then cause a reduction in ductility, or even embrittlement at a sufficiently low testing temperature. The discussion presented above deals with the effects of cold working at a high temperature on the fracturing

Jan 1, 1950

By Walter Gaby

L. C. GRATON, Cambridge, Mass.-May I ask, in connection with one point in the summary, to what extent the author regards actinolite equivalent to tourmaline as an index of high-temperature and presumably magmatic conditions of deposition of the accompanying sulphides? W. E. GARY.-I merely advanced the idea that the mineral actinolite might have some such significance. In the copper deposit at Braden in South America, the ore occurs in an andesite breccia which is cemented by a matrix of sulphides, quartz, and tourmaline. Tourmaline is a high-temperature mineral, and when we find it associated with ores, these are regarded as having come from a volcanic or deep-seated source, hence a primary hypogenetic deposit. Thus we can count on greater continuation of the ore with depth than in some other kinds of deposit, and I thought that the actinolite, being also a high-temperature mineral, might have some such bearing in the case of Mount Morgan. I did not advance this idea as a final conclusion from a study of such phenomena, but thought that it might bear some discussion in view of the fact of the peculiar occurrence of this mineral in a notable orebody. It also occurs with the copper ores at Ducktown, Tenn., and in both cases may only be due to general regional metamorphism.

Jan 12, 1916

By AIME AIME

ONE test is worth a thousand expert opinions, say the engineers of the John A. Roebling's Sons Co. of Trenton, N. J. Confronted with the job of building the cables for the new Hudson River Bridge between Fort Lee and upper Manhattan, the Roebling organization, in spite of its long and varied experience in building cables for suspension bridges of various sizes, recognized that old yardsticks would be of little value in estimating safety factors for the immense span across the Hudson.

Jan 1, 1929

By H. G. Kok

The continuous increase in energy costs has made it necessary to consider a broader use of belt conveyors for the transportation of material from the mine pit to the processing plant. Hard rock has to be crushed before it can be moved by belt conveyors. Systems are in the planning stage for mining hard rock, such as copper and iron ore, by using high-capacity, mobile, or semi-portable crushers. The mobile crusher is located in the pit, and the crushed material is transported by energy-efficient, shiftable belt conveyors out of the pit.

Jan 1, 1983

By Munroe F. Warner

As originally built, the plant of the American Zinc and Chemical Co. at Langeloth, Pennsylvania, was based upon the Joplin and Wisconsin fields as primary sources of zinc ores, the ores being the then normal jig and table concentrates. Construction incorporated standard Matthies-sen and Hegeler kilns without regenerators. With the development of differential flotation, zinc concentrates produced by that process became the basis of operation. These concentrates were very fine, upwards of 90 per cent passing a 300-mesh screen, and had a comparatively low fusing point with marked caking and crusting characteristics. Difficulties and losses quickly developed. In roasting, the ore went through a decidedly fluid state, and spills became serious. Caking and crusting on hearths was severe and dust losses throughout became intolerable. Acid recoveries dropped from the normal ton-for-ton level to 0.85 tons per ton of ore, and choking of Glover towers and acid lines became a problem. In 1926 and 1927 a two-unit sintering plant was built and placed in operation in accordance with the Baelen process for finishing desulphuri-zation with admixture of carbon. This had its beneficial effect in smelting, but the other problems remained. The problem presented was the roasting of Pecos flotation concentrates at the rate of 200 tons daily to a sulphur content suitable for finishing in the sintering plant. Specifications had to be governed by the existing acid plant of four chamber sets built in units of two, rather widely separated, and the sintering plant built in the space between the existing pairs of kilns, of which there was one on the center line of each of the four chamber sets. The problem contained elements of pioneering and experimentation. A thermal analysis and heat balance clearly demonstrated a possibility of accomplishing autogenous roasting, well worth the attempt, because of high fuel costs and resultant economies in operation of the acid plant due to decreased gas volumes and a consequent release of capacity for increasing acid production, a problem also faced.

Jan 1, 1937

By J. F. Kemp

CONTENTS. [ ] I. INTRODUCTION. 1. Situation.-From Monterey in the State of Nuevo Leon, the Sierra Madre mountains stretch away to the southeast and present a steep front to the northeast. The Monterey and Mexican Gulf railway, which connects Monterey with Tampico, follows their general line with its road-bed a few miles out from the foothills. At a distance of 100 miles from Monterey it passes through the town of Linares, and from Linares one can see far away to the southeast the peaks of another group of mountains

Jan 1, 1913

By S. F. Emmons

It was said by many who discussed Professor Posepny's admirable paper on the "Genesis of Ore-Deposits," read at the Chicago meeting of the Institute, in 1893, that its most valuable feature was the clear distinction which it drew between the influence upon ore-deposits of the " vadose " circulation of waters descending directly from the surface, and that of the deep underground circulation of waters generally coming from the depths, and assumed by the author to be ascending through more or less open spaces under the influence of heat. A little later the effect of the oxidizing action of the vadose circulation upon ore-deposits was ably and exhaustively treated by Prof. R. A. F. Penrose, in a paper on " The Superficial Alteration of

Jan 1, 1901

By J. W. Mitchell

Season cracking of 70-30 cartridge brass cases of small arms and artillery ammunition has been under investigation at the Frankford Arsenal for many years. The nature of this stress-corrosion failure has been found to be intergranular. Much of this work, however, has been directed toward improvements in method of manufacturing the cases so as to reduce the tendency to season crack and little progress had been made toward finding the source of the chemical agent producing the inter- granular corrosion. Ammonia has been shown to produce season cracking in brass and is known to be present in certain atmospheres, particularly industrial, in sufficient concentration to cause cracking. However, in the case of small arms ammunition, the hypothesis that atmospheric ammonia is the cause will not hold, since small arms ammunition is hermetically sealed during storage and yet occasional lots are found to have cracked after 3 to 5 yr. storage. Much of the early study of season cracking in small arms ammunition was done by Nicholas H. Murdza of the Frank- ford Arsenal. In 1936, he suggested that the corrosive agent might be one of the decomposition products of smokeless powder and mentioned nitrogen oxides specifically. Then in 1937, Murdza suggested that the breakdown of smokeless powder in storage resulted in the formation not only of nitrogen oxides but also ammonia

Jan 1, 1945

A Progress Report of The Engineering Foundation, which is a history of the Foundation and a report of its activities, has been printed. A limited number may be obtained by members of the Institute by writing to the office of the Institute or to the Secretary of the Foundation.

Jan 11, 1919

By W. G. Matteson

THE Oklahoma legislature recently passed a bill providing for "the creation of an oil and gas department under the jurisdiction of the Corporation Commission, authorizing the. Corporation Commission to appoint a chief oil and gas conservation agent, and conferring exclusive jurisdiction on the Corporation Commission in reference to the conservation of oil and gas, and the inspection of gasoline and oil, the product of crude petroleum, and repealing all acts or parts of acts in conflict therewith and declaring an emergency." Some of the functions of the new bureau include the receiving and filing of all well logs and the direction and supervision of plugging all abandoned oil and gas wells under rules prescribed by the Corporation Commission. The two leading petroleum-producing States of the country, Oklahoma and California, have now established oil and gas bureaus with a staff of inspectors to see that the important rules relating to the conservation of oil and gas are thoroughly enforced. The economic significance and the value of well logs in the conservation work has been recognized and the necessary legal action taken to insure and procure them. William B. Heroy, of the Government Land Classification Board, in a personal communication to the writer, says that the drilling of wells is also regulated by public authority in the Roswell artesian basin in southeastern New Mexico, where a permit must be obtained for the drilling of any well and a certified log of the well recorded with a county official. The method is said to give fairly satisfactory results. In a recent article 1 a National instead of a State Bureau was suggested for collecting and filing well logs. In discussing the paper, L. L. Hutchison characterized such a plan as impractical because the average driller or contractor will often juggle or guess at the log and will not keep the record sufficiently close or accurate, making it necessary to maintain a special man at each well for the sole purpose of obtaining

Jan 6, 1917

By James P. Kimball

THE object of the present memoir is to put on record some practical experiments by the writer in smelting a silicious native magnetite with no other flux than the silicates of its own gangue: This work was undertaken in the spring of 1878 for Messrs. Naylor & Co., of Boston, to whom I am indebted for the privilege of here communicating its results, these having hitherto only been simply announced.* So far as I am aware these are the first instances of the kind in this country that non-calcareous; or rather non-carbonated, magnetites have successfully been used strictly alone as self-fluxing ores in the blast furnace; that is, without the addition of calcareous flux in the form either of limestone, quicklime, calcareous ore, or basic (calcareous). slag. Previous to the spring of 1878, when the Chateaugay magnetic ore was first brought to my notice, its use had been limited to Catalan forges, after "separation" at the ore bed. The blooms and billets made from it in the several forges of Messrs. Weed & Williams, and of Mr. Williams, were well known in the trade as among the best in the market. The Chateaugay ore beds proving of great magnitude, and the ore exceptionally low in phosphoric acid, it commended itself for blast-furnace purposes to Messrs. Naylor & Co., who employed nee to blow-in the charcoal furnace at Pittsford, Vt., on this ore in the spring of 1878., a previous trial of this ore in the same furnace in the fall of 1877 having proved abortive. This was therefore the first time that Chateaugay ore was successfully smelted in a blast furnace, although since well known as a blast-furnace ore possessing superior and exceptional qualities. The Pittsford furnace, although rebuilt in 1844, and subsequently improved by the former owner, the late J. Prichard, is one of the few furnaces of the old type with open breast (Sumpfofen) still active in this country. Its improvements on furnaces of the period, * Bulletin American Iron and Steel Association, XII, 1878, 132, 156.

Jan 1, 1881

By Otto H. Henry

The purpose of this investigation was to determine the equilibrium diagram of the lithium-magnesium pair as a first step in studying the possible usefulness of these alloys as ultra-light structural materials. Review of the Literature The behavior of lithium towards magnesium was first investigated by Masing and Tammann.(1)† In order to prevent oxidation the alloys were made in iron tubes under an atmosphere of hydrogen; temperatures were measured with a glass-protected thermocouple. These investigators found that lithium and magnesium form two series of solid solutions separated by a miscibility gap between 85 and 95 per cent magnesium; that the alloys with 81 and 95 per cent magnesium showed a homogeneous structure under microscopic examination, while the alloy with 89 per cent magnesium contained two distinguishable crystallites; that the curve indicating the beginning of crystallization rises from the melting point of lithium to that of magnesium; and that no compounds of lithium and magnesium are formed. The equilibrium diagram was not plotted because no definite data were obtained for determining the solidus and the position of the miscibility gap in the solid state. The difficulties encountered in this investigation were: (1) that it was necessary to heat them as high as the melting point of magnesium in order to obtain homogeneous melts; at such temperatures the alloys attacked the glass protecting the thermocouple; and (2) that at temperatures above 400" C. the lithium united with the hydrogen to form lithium hydride, thus contaminating the alloys. By applying the same methods as those used in the lithium-magnesium system, Masing and Tammann determined the equilibrium diagram of the

Jan 1, 1934

By Henry M. Howe

What should be the chief aim of a metallurgical laboratory ? Before answering this, let us ask, What should be the chief aim of metallurgical instruction ? Taking a definite case, that of the iron blast-furnace, should we chiefly teach the methods of bosh- and tuyere-cooling, of storing and assembling materials, of removing the iron and cinder, of firing boilers and cleaning stoves ? Or should we aim chiefly to lay clear and bare the nature of the reactions which occur in the blast-furnace, the reason why changes in the rate of driving, in the blast-temperature, in the composition of the cinder, cause their known effects ? Shall we chiefly describe or explain ? Shall we teach chiefly the looks or the reasons ? Put thus, the question admits but one answer. Hours of labored description at a technical school give a less true and clear view of actual metallurgical operations than a brief visit to metallurgical works. If in my teaching 1 take the far more laborious course and lay so very great stress on explanation and so little on description that I seem to err on that laborious side and not to give description enough, the student will quickly make up for my lack of description in his first weeks in the works; he will there learn quickly and easily what I could have described only obscurely and with labor. Details of practice are learned easily and retentively in the works, but with difficulty and slowly at school. With the principles, and especially the chemical principles of metallurgy, the reverse is true. The works have little facility for teaching them; the school has every facility. The place then for explaining, for teaching principles, is the school. But,

Jan 1, 1900

By Linda P. Bono

Some mining engineers are pursuing their destinies in places far removed from what they might have envisioned back in the classroom. The path they follow to work each day may wind down Wall St., Park Avenue, LaSalle, or Market; their offices are in modern skyscrapers which offer all the amenities-air conditioning, thick carpets, attractive decor, and executive lunchrooms, to name just a few. The papers on their desks are a combination of financial figures and feasibility studies. But even in these surroundings there are indications of what these men do and where their professional interests lie-minerals are everywhere, from vast collections to one symbolic paperweight. . . there are sometimes specks of dirt under fingernails from a recent on-site inspection, belying the traditional banker's garb. . . and there are the wistful comments about finding it necessary to get out in the field.

Jan 9, 1978

By E. M. Wise

THE practice of adding moderate quantities of nickel to a variety of bronzes has been employed by foundrymen for many years with several objects in view. In some instances it was desired- to harden the alloy; in others it was to increase the fluidity or to improve the solidity of the castings, or to refine their grain. These important matters have been considered in detail by Pilling and Kihlgren1 and by numerous other workers cited by them, and with the exception of the first will not be considered in the present communication. The possibility of reducing the cost of bronze by replacing a portion of the tin with nickel received attention some years ago by Burgess and Woodward,2 and, as will be shown later, offers attractive savings in cost under present conditions. The age-hardening characteristics of the nickel bronzes of appropriate compositions have been known for some time and were mentioned by Price, Grant and Phillips3 and discussed by Wise4 in connection with their paper. These matters are further considered in recent patents,5 and are becoming of commercial importance in the production of high-strength castings.

Jan 1, 1934