Search Documents

Jan 1, 1940

By Eckley B. Coxe

The subject of this paper will be treated as briefly as possible under the following heads : I. The latest designs of some of the machinery used at these collieries in the preparation of coal. 11. The means employed for elevating, conveying and transporting the coal and slate in and about the breaker. 111. The means employed for raising the coal from the mines to the top of the breaker. IV. The iron breaker as a structure. V. The preparation of the coal as effected in the iron breaker. A key to the plates and the letters and numbers designating different parts, will be found at the end of the paper. I. Preparing Coal. Anthracite coal as it comes from the mines is not marketable. The "run of mine" cannot, as in the case of bituminous coal, be sold. Anthracite, being very compact and practically free from volatile combustible matter, burns only at the surface, and it is, therefore, deemed important to have the lumps as nearly of a uniform size as possible, so that between them a large amount of surface will remain exposed to the action of the air without checking the draught too much, or allowing enough air to pass to cool the coal below the ignition-point, In other words, if the pieces of coal of the size of a chestnut and smaller are mixed with lumps of the size of an egg they fill the air-passages and prevent a free draught. It has long been recognized, therefore, that one of the most important points in preparation is to have a uniform sizing, and also to make as large a number of different sizes as can be produced without too

Jan 1, 1891

By S. N. Singh, M. C. Flemings

Results are presented of a detailed study on the combined influences of ingot dendrite am spacing and thermomechanical treatments on the structure and solution kinetics of high --purity cast and worked 7075 alloy. Solution kinetics were found to depend sensitively on ingot dendrite am spacing and on details of therrnomechanical processing, including amount of reduction and extent of&apos; solution treatment before reduction. An approximate analysis is given for rate of solution of nonequilibrium second phase in the cast and worked structres; results of the analysis are compared with experiment. MICROSEGREGATION in high strength aluminum alloys manifests itself as "coring" (composition differences within the primary aluminum-rich phase), and as interdendritic second phase. The mechanism of formation of the microsegregation is understood, and approximate prediction of the amount of second phase is possible for simple binary systems.1,2 When alloy elements or impurities are present in amounts less than their solid solubility at solution temperature, any phases forming from these elements are termed "nonequilibrium" and can be dissolved by appropriate solution treatment. The rate at which the nonequilibrium phases are removed depends sensitively on their spacing (dendrite arm spacing in the cast material, or band spacing in wrought material). When alloy elements or impurities are present in amounts in excess of their solubility at the solution temperature, second phase particles form an "equilibrium" second phase that does not dissolve in heat treatment and may, in fact, coarsen in such treatment. Usual commercial, high strength, wrought aluminum alloys contain nonequilibrium second phases that were not fully dissolved during ingot processing. They also contain equilibrium second phases resulting from impurities present in amounts greater than their solubility. As has been shown by Antes, Lipson, and Rosenthal,3 and will be demonstrated further in a subsequent paper by the authors,4 significant improvements in mechanical properties of high strength alloys can be achieved by reduction or elimination of these second phases. Methods of elimination are 1) to employ high purity materials to minimize amounts of equilibrium second phase, and 2) to employ suitable thermomechanical processing techniques to fully eliminate nonequilibrium second phases. Work reported herein comprises a study of selected thermomechani- cal processing treatments, and of their influence on solution kinetics of wrought high purity 7075 alloy. EXPERIMENTAL PROCEDURE Melting and Casting. The bulk of the work reported was performed on a single ingot of high purity 7075 alloy. The ingot was 4 in. by 4 in. by 8 in. high, uni-directionally solidified following a procedure previously described.5 The mold was heated to 1350°F before pouring the melt. The bottom chill was carbon coated stainless steel. Water was circulated through the chill after the melt was poured. The 7075 alloy was prepared from high purity virgin material (aluminum, zinc, magnesium) and from master alloys (Al-50 pct Cu, A1-15 pct Cr, A1-5 pct Ti). Final measured melt composition (wt pct) was: Zn Mg Cu Cr Ti Fe Si Al 5.70 2.28 1.35 0.18 0.15 <0.002 <0.012 bal Melting was done in a silicon carbide crucible; all tools were coated with zircon wash to minimize iron contamination; degassing was by bubbling chlorine through the melt. che-rmomechanical Treatments. Detailed studies were made on material taken from a location approximately 13 in. from the chill and 51/2 in. from the chill (i.e., from 1 in. thick slices taken between 1 and 2 in. from the chill and between 5 and 6 in. from the chill). Solution treatment was done at 860°F in an air-circulating furnace with a "bottom drop" arrangement to achieve minimum delay time between solution treatment and quench. Samples solution treated in this way were 2 in. by 2 in. by 1 in. Temperature of the quench water was approximately 10°C. Mechanical reduction was by cold rolling. Samples 11/2 and 51/2 in. from the chill were treated for 12 and 24 hr, respectively, before cold rolling. Reduction by cold rolling was then 4/1, 16/1, and 35/1. In each case, several intermediate anneals (1/2 hr at 860°F) were used to permit reaching the final thickness without cracking; two such anneals were used for the 4/1 reduction, five for 16/1, and six for 35/1. After working, materials were again solution treated for various lengths of time from 0 to 48 hr and quenched in water. Structural Measurements. Secondary dendrite arm spacings were measured using procedures previously described.&apos; For each measurement reported, five photomicrographs were first made at X75. Measurements were made of dendrite arm spacings in at least 20 different grains (grain structure was equiaxed). Grain size measurements were made by running a number of random traverses across photomicrographs of the samples and obtaining the mean lineal intercept. Measurement of the volume percent of second phase and porosity was done by quantitative metallography. A two-dimensional systematic point count was used

Jan 1, 1970

By Lyall, Zickrick

As a result of the studies on recrystallization and crystal growth made in this laboratory, certain theories have been developed. These are expressed briefly in a paper by Dean and Hudson.&apos; One of the principal points brought out in that paper is that in the deformation of a crystal, the energy supplied is distributed to the atoms of the lattice, probably by the forced formation of molecules. It is found that a Maxwellian distribution of the energy among these atoms will account for the grain growth at various temperatures. According to such a distribution the number of atoms with energy above a certain critical value, E, necessary for recrystallization at the absolute temperature T is given by n = Ne-E/kT where N is the total number of atoms. It is apparent that if this line of reasoning is correct, a metal which has been cold-worked and reheated to a temperature below that of complete annealing will have the atoms with the higher energy recrystallized, that is, reduced to normal energy and there will remain only atoms below a certain energy. If this metal is again cold-worked the peak in the number-energy distribution curve will, as compaied with its position after the first cold-working, be displaced toward the regions of lower energies, that is, the temperature of recrystallization will be higher. By a repetition of this process the position of this maximum and hence the recrystallization temperature of the metal could be raised considerably. In order to check this theory, experiments have been made on copper wire. The wire was drawn from 1/4-in. rod to 22 B & S gage and then sample lots were annealed at 400 and 220° C., respectively. The wire annealed at 400° C. gave an elongation of 34 per cent., whereas that annealed at 220° C. gave only 23 per cent. These wires were then drawn by identical practice to 34 B & S gage and the elongation determined after an anneal of 3 min. in an oil bath held at various temperatures. The figures obtained have been plotted in Fig. 1. It will be seen that the

Jan 1, 1927

By George C. Fryburg

The oxidation of platinum at high temperatures (above 800°C) is controlled by boundary-layer diffusion, except at the lowest pressures. The rate of oxidation is determined by the rate of diffusion of oxide through the boundary layer away from the platinum. This is in contrast to the situation in tungsten and molybdenum oxidation, where the rate is controlled largely by the diffusion of oxygen through the boundary layer towards the metal. The difference in mechanism is a consequence of the much lower rate of oxidation of platinum. Evidence is presented that supports this mechanism for the oxidation of platinum. SOME years ago we reported1 a study of the oxidation of platinum in ordinary oxygen in the temperature region above 800°C, where the oxide is volatile. All the data available up to that time had been obtained with platinum crucibles or plates heated in tube furnaces. The results were widely variant and highly dependent on the flow rate of gas through the furnace: the faster the gas flow rate, the higher the measured oxidation rate. These results indicated to us2 that reaction equilibrium was being approached in the furnace and that the rate was diffusion limited. To minimize these effects, we employed1 electrically heated ribbons placed in a cooled bulb. We were primarily interested in the low-pressure region, but some experiments were performed at pressures up to 1 atm. We found a peculiar pressure dependency which was explained on the basis that the rate of oxidation was proportional to the pressure at all pressures, but that with increasing pressure an increasing fraction of the volatilizing oxide was back-reflected to the ribbon by the surrounding gas molecules. The oxide molecules are not stable at the temperature of the platinum and are decomposed on impact, the platinum being re-deposited on the specimen. Because of the limitations of space, this explanation was offered summarily without detailed support. Recently, Jaffee and associates3, 4 have suggested that the pressure dependency of our data up to 0.5 torr could be explained on the basis of a Langmuir-type adsorption of molecular oxygen followed by dissociation. Since the correct explanation of the effect of pressure on the oxidation rate is a necessary requirement to the development of the basic mechanism of the oxidation reaction, we felt that the back-reflection theory should be presented in more detail. This is the object of the present paper. RESULTS AND DISCUSSION A typical set of results showing the pressure dependency of the oxidation reaction is presented in Fig. 1, where we have plotted, on logarithmic scales, the rate of oxidation, R, vs the pressure, p. For comparison some results of Krier and Jaffee4 and of Raub and plate5 are also shown. These data were taken at atmospheric pressure using furnaces. The effect of reaction equilibrium within the furnace is apparent from the much smaller values that these observers obtained: Raub and Plate In O2 found a rate of 3.1 µg cm-2 hr-1 compared to our value of

Jan 1, 1965

By R. W. Raymond

In my former paper (Bans., xii., 410) I quoted the ruling of Judge Hallett, of Colorado, in the "Iron-Smuggler" case, tried before him in June, 1882. Under his charge, the jury in that case found for the defendants, practically declaring that the deposit on the outcrop of which the Iron Silver Mining Company&apos;s claim was located was not a " lode," or else that the portion of it within that claim was not the apex. The case was appealed, and the decision of the Supreme Court, given in February, 1886, is reported in 116 U. S. Reports, p. 529. It simply declares that there is nothing in the charge of Judge Hallett to warrant the setting aside the verdict. The definition of a legal lode given in that case, and quoted in my paper at the page above-named, is perhaps the best of several which Judge Hallet has pronounced. That is to say, his earlier definition, that " a lode or vein is a body of mineral, or mineral-bearing rock, within defined boundaries in the general mass of the mountain," is here accompanied with further explanations, which relieve it from the requirement on one hand, that the body shall be continuously ore-bearing if it he only well-defined, and, on the other hand, that the boundaries shall be well-defined if the ore-bearing body be proved to exist. So far as this particular case is concerned, the approval of this ruling by the Supreme Court merely prevents any re-hearing as to the face. Undoubtedly, the evidence was conflicting; and the jury chose to believe, for the purpose of that occasion, the " experts " who

Jan 1, 1887

PURPOSE OF UPDATED ESTIMATE FOR MINERAL INVENTORY BLOCKS During the production stage of an open pit porphyry copper mine it was observed that the expected production grade, as determined from the block inventory estimates, often differed greatly from the head grade of ore delivered to the mill. It was determined that, for purposes of production scheduling and monthly forecasting, better in situ grade estimates for mining blocks were necessary. Because all of the bench blastholes were being sampled, and periodic holes were being drilled into the next underlying bench, much more sample data existed than was being used for estimating the grade of nearby mining blocks. It was reasoned that, by periodically updating the mineral inventory block file over the benches scheduled for mining in the next time period using all existing data, better estimates and forecasts for production grade could be made. BLASTHOLE SAMPLE DATA MANAGEMENT The collars of all blastholes in each mined bench were surveyed and assays run on the cuttings representing the full 12-m (40-ft) bench height. The blastholes range from about 5 to 6 m (16 to 19 ft) apart along the front of the bench as well as perpendicular to the front. Overbreakage often left larger spacings between successive blasts. Fig. 17-1 is a plan map of blastholes on a typical mine bench. All blasthole data were keypunched to a format resembling that of the 12-m (40-ft) composite assay data file as follows: [Collar Coordinates Compite Assoy Hole ID Northing East Elewotion Total Copper Oxide Copper] Because of the many blasthole samples available, and in order not to use excessive computer time for running kriged estimates for 30.5 X 30.5 X 12-m (100 X 100 X 40 ft) blocks adjacent to and beneath the mined area, the decision was made to average all the blastholes falling with each 15.2 X 15.2-m (50 X 50-ft) mined block, and use the mean value of the samples as a regionalized variable for purposes of assigning kriged estimates and estimation variance to adjacent unmined blocks. In other words, instead of using individual blasthole samples for making kriged estimates, the holes were grouped by blocks and assay values were averaged and assigned to the centroid of the holes within the block, which was then treated as a single regional variable for purposes of kriging. See Fig. 17-2. VARIOGRAM COMPUTATIONS AND KRlGlNG RESULTS With the many blasthole samples it was possible to compute directional and vertical experimental variograms for both sulfide and nonsulfide copper assays falling within the enriched mineral zone for the full 12-m (40-ft) sample support. Due to the close spaced drilling, excellent definition of the experimental variograms was possible, and the spherical model exhibited good fits. A three-dimensional kriging program was then run over the two or three mine benches involved in the inventory update, and estimated grades reassigned to all mining blocks falling within the range of the new blasthole assay data according to the anisotropisms of the deposit. Better confidence limits could then be assigned to scheduled mining blocks and better short- range forecasts made. An interactive kriging computer program was also applied for the purpose of determining the kriging variance or estimation of error for larger, irregular mining blocks representing the monthly production from a particular bench. The interactive program permitted the operator to enter the limits of the irregular block onto the screen of a cathode ray tube (CRT) as a series of points around the perimeter of individual gridded blocks making up the larger irregular block. The computer then was programmed to calculate the kriging variance of the larger block using all samples fall- ing within range. Thus the limits of estimated grade could be established at any confidence level. Fig. 17-3 illustrates the output from the interactive kriging program showing the sample points entering into the grade and kriging variance computations, and also the kriging coefficient assigned by the computer to each sample.

Jan 1, 1980

By F. P. Dewey

The most serious problem that confronts the lead-smelter is the waste caused during smelting by the volatilization of both lead and silver, which are consequently lost in the form of fume. It is not difficult to collect a portion of the solid materials passing out of the

Jan 1, 1890

By A. U. Seybolt

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrence of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except .conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below.

Jan 1, 1935

By W. Mostowitsch, H. O. Hofman

In a previous paper,&apos; The Behavior of Calcium Sulphate at Elevated Temperatures with Some Fluxes, we published the results of our investigation into the behavior of calcium sulphate in air; that is, under oxidizing conditions. The results as a whole hold good for a neutral atmosphere, or one which has no chemical effect upon calcium sulphate. The present paper deals with the behavior of calcium sulphate under reducing conditions, the reducing-agents employed being carbon monoxide and carbon, and the changes the calcium sulphide formed undergoes when it is subjected to an oxidizing-roast. Technical literature deals very sparingly with the subject. The information furnished by the recent leading chemical manuals is general. Thus Dammer,2 Missan,3 and Abegg4 quote Berthier as having reduced, in 1823, calcium sulphate with carbon, and Stammer as having done the same in 1851

Jan 1, 1911

By G. W. Powell

G. W. Powell (Ohio State University)—Appleton and Bever measured the quantity Es which, for a solid torsion specimen, is basically an average quantity. Es is the amount of energy stored in a solid torsion specimen strained to a surface shear strain of divided by the total number of gram-atoms of alloy in the specimen. It would seem more meaningful and rigorous to deal instead with the quantity which is the energy stored per gram-atom of an alloy uniformly strained to the shear strain . The purpose of this discussion is to demonstrate that as a function of y is readily obtained from the torsion data. radius of the torsion specimen, shear strain at the surface of the torsion specimen density of the alloy, atomic weight of the alloy, and total energy stored in unit length of the torsion specimen. The energy stored in unit length of an elemental tubular section of the torsion specimen is, as given by Appleton and Bever, where E is expressed as calories per gram-atom. The energy stored in unit length of the torsion specimen is

Jan 1, 1963

By Jim D. Mote, Eugenia M. Howard, Willis L. Barmore, John E. Dorn

The effect of stress and temperature on the creep rate of Ag-33 at. pct A1 and Ag-33 at. pct Al-1 at. pct Zn for prismatic slip was determined over a range of temperatures from 440º to 700°K. The alloys exhibited a brief initial inverted transient creep over which the creep rate increased slightly to a steady-state value which depended only on the stress and temperature, regardless of the previous strain history. The steady-state creep rates were found to be given by: where the activation energy is independent of the stress and strain and agrees fairly well with that estimated for diffusion. The observed creep behavior was shown to be in qualitative agreement with a model based on the stress-induced local disordering in the vicinity of a dislocation. OVER the past fifteen years, considerable progress has been made in correlating the experimen-entally observed plastic behavior of pure metals over each temperature range with one or more of a series of theoretical strain-rate controlling dislocation mechanisms. Despite the current interest in the plastic behavior of intermediate phases and inter metallic compounds, however, very little has been done in identifying the operative dislocation mechanisms in these materials. It is anticipated that the plastic behavior of intermediate phases can be rationalized in terms of the same dislocation mechanisms that are appropriate to pure metals and a solid solutions, provided the additional complexities arising from crystal structure, bonding, long-range order, short-range order, and defect lattices are taken into account. As part of a more extensive investigation on the plastic behavior of intermediate phases, Mote, Tanaka, and Dorn1 recently reported on the effect of temperature on the yield strength for prismatic slip in the hexagonal Ag-33 at. pct A1 intermediate phase as recorded in Fig. 1: Over Region I the deformation was observed to take place as a result of the thermally-activated Peierls mechanism, and over Region II the athermal disordering mechanism applied. The experimental data at that time, however, were not sufficiently extensive to identify the thermally activated mechanisms operative over Region III. It is the purpose of this investigation to attempt to identify the mechanisms that are operative over this high-temperature region. It will be shown that the same mechanism operates all over Region Ill, although the activation energy for this mechanism is in good agreement with that for diffusion, the process cannot be attributed either to the motion of jogged screw dislocations or the climb of edge dislocations. The results, however, are in good qualitative agreement with stress-induced disordering localized at dislocations. EXPERIMENTAL PROCEDURE The alloys studied in this investigation were prepared from silver, aluminum, and zinc (each of purity greater than 99.995 pet) by induction melting under an argon atmosphere and chill casting in a copper mold. Rectangular bar single crystal specimens (1/4 by 1/8 in. in cross-sect ion) of Ag-33 at. pct Al were grown in vacuum by a modified Bridgman technique. Similar Ag-33 at. pct Zn specimens were produced by an identical technique employing an argon atmosphere. The specimens were so oriented that the angle 90-Xo between the tensile axis and the normal to the prismatic plane and the angle A, between the tensile axis and the slip direction were 45 ± 1 deg. The effect of a change in temperature on the creep rate and a change in stress on the creep rate were determined over the temperature range

Jan 1, 1963

By G. H. Clevenger

(Continuing the discussion of the paper of James Johnston, presented at the New York meeting, February, 1914, and printed in Bulletin No. 85, January, 1914, pp. 107 to 133.) This paper cannot fail of being of great interest and value to all who are interested in the cyanide process, on account of the important developments which it records. Mr. Johnston is to be commended for the large amount of detail which he gives, and the company and its management for permitting the publication of data of this character, which while of great value to others could well be considered private property. It might be discussed from a number of standpoints: First, as an example of recent practice in mill and cyanide plant construction; second, the mill practice; third, the cyanide practice; and fourth, the new features in cyanide treatment involved. Perhaps a more vivid way of expressing it would be : First, the equipment or tools with which the various operations are carried on, are they the best and most efficient which could have been selected for their respective uses; and, second, is the best use in every case made of these tools? It may be well inquired is the highest possible recovery of silver made at the lowest cost per ounce recovered? For after all, the making of the greatest ultimate profit is inseparably associated with successful metallurgical practice; there must therefore be at all times a careful balance maintained between recovery and cost of obtaining it. I wish to call attention in a very general way to the equipment used and to an anticipation of questions which are bound to arise in this connection. However, the. bulk of my discussion will be confined to the presentation of certain additional data, together with a more or less general discussion showing the line of development which leads up to the present practice and .the applicability of certain features of it to similar problems elsewhere. There are a number of vital points of broad general interest involved in Nipissing low-grade practice upon which metallurgists will by no means be agreed to which I wish to call particular attention in the hope that it will lead to the presentation of data y others of practice in other districts which will&apos; assist in reconciling this divergence of opinion.

Jan 7, 1914

By Bertrand S. Summers

The technologist who has devoted much attention to the foundry-business will perhaps have noticed that the present scientific development of foundry-practice is in a condition similar to that of the steel-business some twenty years ago. In many cases chemistry is looked upon with suspicion, and the old cutand-try-methods are still in vogue, especially in the smaller foundries. The larger works have laboratories and more extensive means for applying science, and have devoted considerable time and attention to the improvement of foundry-practice. This is more especially true in the East, although in the West there are numerous firms devoting considerable attention to improving their metllods through the application of chemistry to work in the iron-foundry. It is hardly necessary to dwell extensively upon the effects of the different metalloids associated with iron, in pig- or castiron, in the way they are given in most text-books. The writer has thought proper to consider more particularly new developments in eupola-practice, particularly those pertinent to the discussion of the physics of cast-iron. In this connection some new ideas which recent practice has developed will be mentioned, and some results of practical tests along the same line will be described. Yet it has been deemed advisable also, by way of introduction, to outline the effects of the metalloids as they are described in most text-books, without going into detail. The question is sometimes asked, What is the most important element governing the quality of cast-iron &apos;for any particular purpose ? It would seem that right here lies the basis for the greatest difference of opinion. Some twenty years or more ago, silicon was regarded by foundrymen as one of their worst

Jan 1, 1899

By G. B. Craig, J. Rezek

The critical resolved shear stress of zone-refined zinc single crystals deformed in tension is found to increase with increasing amount of striation substructure. The increase in strength with numbers of striations can be accounted for by a dislocation pile-up mechanism. A somewhat different means of plotting stress-strain data is introduced which allows a more unambiguous choice of yield stress to be made. FEW systematic studies of the role played by mac-romosaic or striation-type substructure in the de- formation of high-purity metal single crystals grown from the melt have been reported. McGrath and Craig&apos; found that striations increased the critical resolved shear stress of zone-refined aluminum crystals, postulating a dislocation blockage by the striations as the strengthening mechanism. Lauri-ente and Pond2 found that, as the etch pit density increased in aluminum crystals grown from the melt, the critical resolved shear stress also increased. Fleischer and Chalmers3 also found changes in the critical resolved shear stress of aluminum crystals grown from the melt at varying rates, but could not be certain whether an increase of strength with rate was due to a higher concentration of impurity in the gage length or to an increase in the number of small-angled boundaries. An early work by Hibbard4 indicated that copper crystals containing lineage boundaries were stronger than those free from this type of imperfection.

Jan 1, 1962

By Ernest Stütz

(New York Meeting, October, 1918.) THE problem of increasing blast: furnace efficiency through diminution of flue-dust production while operating with burdens consisting largely of fine ores has of recent years attracted the attention of metallurgists, whether directly or indirectly interested in the economies of iron smelting, and the various methods evolved from theory or practice have been submitted to wide discussion. After the very thorough and, at that time, exhaustive view of the whole subject, which was afforded to the industry by the meeting of this Institute in February, 1912, the subject was again taken up at the meeting of the Verein deutscher Eisenhüttenleute at Diisseldorf in December, 1912. While American and German conditions are not entirely identical, it may be of interest to give here the words of the gentleman summing up the discussion at the Diisseldorf meeting: &apos; The chief advantage offered by the use of briquettes lies in the fact that disturbances in the furnace, caused mostly by the presence of fine ores in the burden, are avoided, and that blast pressure can be considerably reduced. The resulting economies cannot be overrated, as, with lower blast consumption per ton of product, the installation will be able to take care of increased production. In consequence of lower pressure and speed of blast, heat is more efficiently utilized, flue gas temperature is lowered, and coke particles are less liable to be carried along with the flue dust, of which considerably less is produced. Finally, by increased regularity of operation and higher . temperature in the lower parts of the furnace, the quality of the product is improved. The question of briquetting iron ores has grown to be one of the most important in the iron industry, and, it is not any more a question of what is the cost of briquetting ton of ore, but what, in using ore briquettes, is the cost of production of a ton of iron.&apos;

Jan 7, 1913

By Max Barber

PRESENT equipment and practices in open-pit mines of the Lake Superior iron ranges have been described recently in some detail by A. H. Hubbell.1 It is anticipated that any further improvements will be the result of gradual evolution of present methods and equipment, just as those now used have been gradually evolved from earlier methods. An exception to the process of gradual evolution during the last decade has been the adoption of electric power for operating shovels and trains in open-pit mines, but it is not expected that any such revolutionary changes will be made in the future. The use of Diesel, engine equipment will gain considerable headway, no doubt, and will find favor in certain lines of operation as improvements and adaptations are evolved to meet particular requirements. The question of installing belt conveyors for handling material from deep mines of restricted area, where haulage grades become a serious consideration, or even for transferring earth, rock, or ore material for distances of several miles, is now being studied and some very interesting data are being obtained.

Jan 1, 1932

By H. I. Aaronson

The nucleation of pearlite at proeutectoid ferrite is inhibited, to an increasing extent, at the following locations: At twin boundary-nucleated ferrite, between closely spaced ferrite sideplates, and at intragranular plates. These effects are discussed in terms of the influence of transformation strain energies and of the interfacial free energy of austen-ite:ferrite boundaries on the rate of pearlite nucleation. The growth of pearlite into the interiors of austenite grains from the region of the grain boundaries is markedly restricted when low reaction temperatures and large austenite grain sizes permit the development of interlocking networks of intragranular ferrite plates. PREVIOUS investigators have made extensive studies of the interactions which occur between the proeutectoid ferrite and the pearlite reactions from the viewpoint of the mechanisms through which pearlite interferes with the nucleation and growth of proeutectoid ferrite.1-3 In the present investigation, the processes through which proeutectoid ferrite (hereafter termed simply "ferrite") can reduce the rate of formation of pearlite have been explored in some detail. A steel with a relatively low carbon content, in which the ferrite reaction can compete successfully with the pearlite reaction over a wide range of reaction temperature, and exceptionally coarse-grained specimens, which further emphasize the role of the ferrite reaction, have been employed for most of this work. A brief examination also has been made, however, of the effects of smaller austenite grain sizes upon these processes. Experimental Procedure The steel employed had the following composition: 0.29 pet C, 0.76 pet Mn, 0.25 pet si, 0,007 pet S, and 0.005 pct P. This alloy was homogenized for 48 hr at 1250°C. The investigation was performed

Jan 1, 1959

By J. R. Low, A. M. Turkalo

ManY qualitative observations have been made concerning the relationship of the carbide dispersion and the mechanical properties of steel. With reference to the strength and hardness we know that for a given composition a steel having a fine pearlitic structure is stronger than that having a coarse pearlite. The martensitic structure tempered at a relatively low temperature and having finely dispersed carbides gives greater strength than that given by the martensitic structure tempered at a relatively higher temperature and having a coarser

Jan 1, 1959

By Francis B. Foley

From the point of view of the metallographist, the adaptation of x-rays to the study of the crystal structure of metals is of the greatest importance. While one may hardly consider the findings resulting from x-ray study as revolutionary, their positive nature, compared with the deductions we have been forced to accept from the work that had gone before, gives firmer ground on which to build and furnishes new fields for speculation. Prior to the advent of the crystallogram, the best work on the crystal structure of steel was that of Osmond and Cartaud.&apos; They concluded, from their investigation with percussion figures formed at various temperatures, that alpha, beta, and gamma irons belonged to the cubic system and that they showed well-marked specific characteristics and could not have the same internal structure. What the internal structures were, they had no direct method of determining; but from a consideration of the fact that the 001 plane (that parallel to the cube face) is a plane of perfect cleavage and minimum hardness in alpha iron and that the 111 (octahedral) plane is by far the most important in the crystallography of gamma iron, they were led to suggest the simple cubic arrangement as that of alpha and the face-centered cubic arrangement as that of gamma iron. They suggested the body-centered cubic arrangement as that of beta iron. The atomic arrangement of the various crystal forms of iron has been quite definitely determined in recent years by means of x-rays and the work of Westgren2 and Weatgren and Phragmen3 has been rather conclusive. They not only determined the atomic arrangement of alpha, beta, and gamma iron but also that of the high-temperature modification delta.

Jan 1, 1926