Search Documents

By Bruce A. Kennedy

If it had not been for the persistent cold wind, the sun blazing out of a cloudless blue sky would have made it one of those warm, idyllic early spring days which attract the socalled "snowbirds" to Northern Mexico for a vacation at this time of year. At a drill site perched on top of a rather exposed mountain we were installing a number of borehole extensometers in diamond drill holes. A Threading Problem For the uninitiated in geotechnical instrumentation, a borehole extensometer is a series of anchors installed at various depths in a borehole, each anchor being independently connected by a tensioned wire to a measuring device set in the collar of the hole. Any movement of the rock at depth is detected by the anchors and transmitted by the wires to the measuring device. Flexible plastic tubing is used as a spacer between the anchors and the measuring wires are run up the inside of the tube. At this particular site we were installing an instrument string nearly 1000 ft in length. Threading wire only 0.041 in. in diam through 1000 ft of plastic pipe is almost as difficult as getting the proverbial camel through the eye of a needle.

Jan 1, 1971

By Persifor Frazer

Comparative columns expressing the series of rocks of the lower half of the Mesozoic age in this country and in Europe are not yet definitely established. The following represents a co-ordination of the beds in England and Germany,* with a list of materials to be worked in from this country .†

By David T. Day

In 1897 I published a proposed explanation for the variation in color and specific gravity of Pennsylvania oils. A resume of this subject mas also presented at the First International Petroleum Congress, in Paris, in 1900. Since that time

Jan 1, 1911

By William Hall

THE product obtained by roasting stibnite is likely to contain some unoxidized antimony trisulphide and a mixture of antimony trioxide and antimony tetroxide. It was desired to determine, as accurately as possible, the condition of the antimony as well as the total quantity present. Attempts were made to separate the trisulphide and the two oxides by methods based upon their varying solubilities in different solvents, but no satisfactory results were obtained in this way. It was found, however, that by determining the total antimony content, the antimony present as trioxide, and the antimony present as trisulphide, a good idea of the chemical composition of the roasted product could be obtained. The total antimony was determined by dissolving the sample in concentrated hydrochloric acid, reducing the antimony entirely to the trivalent condition by means of hydriodic acid and eventually titrating the antimony back to the pentavalent condition by means of iodine in the presence of sodium bicarbonate.' The details of the procedure are as follows: Weigh out 0.25 gram of the roasted product into a trapped flask (Fig. 1), add 4 grams of powdered tartaric acid, 2 grams of potassium iodide and 40 c.c. of concentrated hydrochloric acid. Boil the solution gently for 5 min. and then cool to room temperature by shaking the flask while holding it under running water. Then, very carefully discharge the iodine color by the cautious addition of 0.05-normal sodium thiosulphate solution, adding a little starch toward the last. Nearly neutralize the acid with ammonia solution, but leave the solution distinctly acid. Pour the slightly acid solution into 200 c.c. of water con-

Jan 1, 1916

By John Birkinbine

A specimen of brown hematite, taken from an iron-ore mine near Anniston, Alabama, exhibits a metallic streak or thread running throngh it. This specimen having been sent to me, I have no personal knowledge of its occurrence; but Mr. Albert E. Noble

Jan 1, 1895

By H. L. Marcus, C. D. Turk

Titanium was physically vapor-deposited by electron beam high rate evaporation. Rates of 50,000 and 85,000Å per min at deposition temperatures of 480°, 535°, and 595°C were used. Deposited thickness ranged front 0.004 to 0.010 in. The evaporated titanium had a high degree of basal Plane texture. The specimens were tested in tension at temperatures ranging from 78° to 520°K. From the data, the yield stress, thermal component of the yield stress, and work hardening characteristics were found as a function of temperature, deposition rate, and deposition temperature. It was found that Taylor's equation, best fit the work hardening data with m = 1/2. MANY investigations have been made on the tensile deformation characteristics of commercial- and high-purity titanium.1"7 The data obtained from these experiments emphasize the fact that the mechanical properties are generally related to the method of production. The correlation of mechanical properties to production history arises from the dependence of impurity concentration on the extraction and melting technique used. Additional effects are derived from crystallographic texturing which can result from fabrication history. Lee and Backofen8 and other investigators9 have shown that crystallographic texturing in titanium sheet has a significant effect on the deformation characteristics. Bunshah and Juntz10 prepared high-purity titanium by high rate physical evaporation techniques. These authors found the deposited material to have a columnar structure with grain sizes ranging from 12 to 104 µ, depending upon the substrate temperature. The room-temperature strengths of the coarse-grained distillate were similar to arc-melted, rolled. and annealed crystal bar titanium. Commercial-purity titanium was also produced experimentally in our laboratory using high rate physical vapor deposition techniques. The commercially pure material has a finer structure than the high-purity distillate,10 and is highly textured. Since the method of preparation and degree of texturing affect the mechanical properties, a research program was initiated to determine the temperature dependence of the yield stress and work hardening characteristics as a function of high rate deposition parameters. This paper relates the results of the investigation. EXPERIMENTAL A) Material Preparation. The titanium was received in the form of commercial-grade 0.096-in.-diam wire which has a composition of 0.016 pct C, 0.0037 pct N, 0.110 pct 0, 0.011 pct H, 0.05 pct Mn, 0.051 pct Fe. balance Ti. The wire was continuously fed into a vacuum evaporation unit as shown schematically in Fig. 1. The deposition chamber was evacuated, purged with argon, and reevacuated to a pressure of 10-5 Torr which was maintained during deposition. A focused electron beam was used to evaporate the titanium from a water-cooled copper crucible. The titanium vapor was condensed onto a preheated titanium substrate. The temperature of the substrate was controlled within ±5°C for the deposition temperatures of 480°, 535°, and 595°C. Control of the input power enabled the use of two deposition rates. 50,000 and 85,000Å per min. The evaporated titanium had a final analysis similar to that of the input titanium, within experimental limits. B) Testing. The evaporated titanium was physically stripped from the titanium substrate and machined into tensile specimens with 1-in. gage lengths. In addition, tensile specimens of as received annealed 35-A titanium sheet with a 20 µ grain size and 45 pct cold-rolled 35-A were also prepared. All specimens were tested in tension in an Instron at a strain rate of 3.3 x 10"4 in. per in. per sec. Proportional limit has been used as a measure of yield strength. Tests were conducted at 78°, 220°, 300°, and 520°K. Metallography, X-ray diffraction, and electron microscopy were used to correlate structure with the deposition parameters and mechanical properties. Room-temperature X-ray measurements were made to determine the phases present. Pole figures and a scans were made to determine deposition texture. Because the vapor deposition was symmetrical about the normal to the substrate, there was no preferred di-

Jan 1, 1969

By Walter J. Johnson

The coals in northern Wyoming and Montana are free-burning and non-caking and range from lignite to bituminous C in rank. Strip and underground mining are employed to supply railroad, utility, industrial, and domestic fuel. The market area includes Iowa, Nebraska, Minnesota, North and South Dakotas, Wyoming, Montana, the Pacific Northwest, and western Canada.

Jan 12, 1953

By Frank Firmstone

In the summer of 1842 my father, William Firmstone, was engaged by Charles Jackson, Jr., of Boston, to examine the conditions in the Lehigh valley as a site for blast-furnaces using anthracite for fuel. In consequence of his report, he was further engaged by Mr. Jackson to build a furnace for him and his partners on the Lehigh canal, 2 miles above the mouth of the river at Easton. Work was begun in the fall of 1842, and the first furnace blown-in in 1844. The history of the works, therefore, from 1844 to 1887, when my own connection with them ceased, covers only four years less than the whole period of the rise, culmination, and commencement of the decline in the smelting of iron with anthracite in America, the beginning of which, in a commercial sense, may be put in 1839.' Although this paper, as the title indicates, is concerned almost exclusively with the furnaces at Glendon, still what was done there was more or less influenced by current opinion in the district, and even reflects, to some extent, the changes in opinion and practice with mineral fuel the world over. No. 1 Furnace was built of red brick, on four piers, had three tuyeres and fore-hearth and tymp, as was universal with furnaces using mineral fuel until the introduction of Lurmann's cinder-tuyere. The dimensions and profile are shown in Figs. 1 and 2. The first hearth (Fig. 1) was of sandstone; all after were of fire-brick (Fig. 2). The profile was no doubt derived directly from Gibbons's furnace,2 for it appears from W. Firmstone's note-books that in October, 1840, he visited " Gibbons' new furnaces building at Corbyn Hall," and I have an old drawing,

Jan 1, 1910

By H. C. Meister

The zinc-smelting industry of the United States has grown very rapidly in recent years and bids fair to outrival that of all other countries in the future. On account of the geographical situation of the chief ore-supplies, the industry may be divided into two main groups, the eastern and the western. The eastern and older group includes the works of Penn-

Jan 1, 1905

By R. W. Raymond

At the Liége meeting of the Iron and Steel Institute of Great Britain, in August, 1873, and also at the Vienna Convention of Mining and Metallurgical Engineers, at the end of August, and at the convention of German geologists, at Wiesbaden, in the first part

Jan 1, 1884

By H. H. Stout

IN the early fall of 1025, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500° to 1600°F. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F." Smoot's reaction, after a few moments considera-tion, was, "It looks perfectly all right to me." The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after confer-ring as to ways and means, decided to go ahead with preliminary laboratory experi-ments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: I. Since brittle cathodes were often unin-tentionally produced, it seemed probable that the laws controlling this type of deposi-tion could be ascertained. 2. We had already proved the gas-clean-ing feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia Uni-versity for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrounded and heated by a resistance coil of Nichrome wire. Broken tough cathodes were used.

Jan 1, 1940

By Ingersoll Olmsted

These ores are of two classes, Bessemer and non-Bessemer, existing in separate, though adjoining, beds. Both are carbonates, with small admixtures of oxides and other combinations. To prepare them for market they are roasted in kilns, which have already been described by Mr. John Birkinbine at the Troy Meeting, October, 1883 (Trans., xii., 378). Concerning their size, arrangement, etc., I need, therefore, only repeat that they are 60 feet in height; have wrought-iron shells 24 feet in diameter; are lined with fire-brick, and supported by cast-iron mantel and columns.

Jan 1, 1889

By W. C. Peters

Geologists take the role of mine geologist when they apply their science to the design and operation of a specific minerals project. In doing so, they use the entire spectrum of procedures in economic geology and engineering geology to deal with a specific system of orebodies and associated environment. The objectives are established by stages in the life cycle of a mining operation as it goes from a prospect to a development project and on to a mine. This paper summarizes the elements of a mining geologist's role, with examples highlighted from the preceding papers.

Jan 1, 1984

Jan 1, 1887

By E. V. Potter

For a nurnber of years, it has been known that manganese made by electro-deposition under certain conditions is ductile while under other conditions it is very brittle. The ductile metal is gamma manganese normally stable only between 1100 and 1138°C1; the brittle metal is alpha manganese, stable up to 727OC. The ductile metal is not stable, but gradually changes to the brittle form; the time required to complete the transfornlation is about 20 days at room temperature. Other observations have indicated that the transformation is completed in 10 to 15 min. at about 125°C, while at — 10°C, no appreciable change occurs in 9 months. The properties of gainma and alpha Illanganese in the pure state are ordinarilj difficult to determine because the gamma structure cannot be retained by normal quenching procedures and alpha manganese is so brittle, it is difficult to obtain specimens free from flaws. In a recent investigation2 some properties of gamma and alpha manganese were determined by studying the ductile electrolytic metal and determining the changes in its properties as it transformed to the brittle alpha form. These investigations provided an excellent opportunity for following the progress of the transition and studying its mechanism. The results of a series of such investigations are reported in this paper. Procedure Various properties of manganese were determined starting with the metal in the original ductile gamma form and following the subsequent changes in its properties as the metal transformed to the brittle alpha form. These observations were made at various temperatures, the data providing information regartling the mechanism of the transformation as well as the effect of temperature 011 the transition rate. Structure and resistivity values gave the most significant results, so this paper is concerned primarily with them. The structure was studied microscopically as well as by X ray diffraction. The resistivity was determined on strips of the metal by measuring the potential drop across a given length of the specimen. Current was passed through the specimen by wires soldered to its ends, and the potential connections were made by wires looped around the specimen near its center. The current was determined by the potential drop across a standard resistor connected in series with the specimen, the potential drop being measured on a potentiometer. In the temperature range from room temperature to 100°C an ordinary drying oven was used to heat the specimen. This was entirely satisfactory except at 100°C, where the time required to heat the specimen was long compared to the transition time, making the initial section of the resistivity curve unsatisfactory. To overcome this limitation, at 100°C and higher a thermostatically controlled oil bath was used to heat the specimens. The block on which the specimen was mountetl was plunged into the hot oil at the start of each test. The heating time was thereby reduced from 5 min. to about 6 sec, and dependable resistivity values could be obtained through 160°C. At this point the whole transition, including the warm-up time for the specimen, required only about 20 sec and it was not considered worth while trying to extend the temperature range further. Aside from the heating problem, the problem of making a sufficient number of accurate resistivity determinations became more and more difficult as the temperature was raised. Using the manually operated potentiometer, 100°C was about as far as it was possible to go. At this temperature and above, a self-balancing photoelectric recording potentiometer was used. Its response was quite rapid, and it proved to be entirely satisfactory all the way through 160°C, where the tests were stopped because of the specimen heating problem rather than any limitation of the potentiometer recorder. The metal used in these tests was prepared at the Salt Lake City laboratory of the Bureau of Mines. The method of preparation is discussed in a paper by Schlain and Prater.3 The sheets were about 2 3/8 by 5 3/16 in. and varied from 10 to 16 mils in thickness. They could be cut readily into pieces suitable for the various tests. X ray and microstructure determinations were made on pieces about 1/8 to 1/4 in. wide and about 1 in. long, while resistivity measurements were made on strips as long as possible and about 55 in. wide. The thickness of each sheet was not uniform over all its surface. This had no bearing on the X ray and microstructure determinations, but sections as nearly uniform and free from flaws as possible were chosen for the resistivity determinations. The gamma manganese was electro-deposited at 30°C, the time of deposition ranging from 5 to 12 hr for each sheet. Whenever possible, the tests were started directly after the metal was stripped from the cathode; otherwise the sheet was placed immediately

Jan 1, 1950

By T. E. Davidson, A. P. Lee

It is known from the early work of Bridgman that the two lowest-pressure transitions (I-II and II-III) are accompanied by substantial and abrupt changes in resistivity and Volume. However, unlike the temperature -induced allotropic transformations observed in such elements as lithium, cobalt, tin, and so forth, there is little actually known about many of the characteristics of the pressure-in&ced transitions. This current work involves an examination of the structural and transformation characteristics of the bismuth I-II and II-III transitions under hydrostatic pressures. The relationship of initial structure to the transformation pressure, rate, resistivity change, and resultant structure is discussed. It is shown that the transition pressure and transformation rate are independent of the presence of grain boundaries and associated anisotropy-induced deformation. An observed hysteresis in both the I-II and II-III transitions is shown. BISMUTH is one of the most interesting of the elements exhibiting pressure-induced polymorphs since it undergoes several allotropic transformations at pressures below 90,000 atm. It is known from the early work of bridman1,2 that the two lowest-pressure transitions (1-11 and 11-111) are accompanied by substantial and abrupt changes in resistance and volume. However, unlike the temperature-induced allotropic transformations observed in such elements as lithium, cobalt, tin, and so forth, there is little actually known about many of the characteristics of these pressure-induced transitions. It is the purpose of this work to examine some of the structural and transformation characteristics of the bismuth 1-11 and 11-111 transitions under hydrostatic pressures. Another interesting characteristic of bismuth is that, in its polycrystalline form, hydrostatic pressures of sufficient magnitude will induce severe progressive plastic deformation in the region of the grain boundaries.3 This deformation, which has also been observed in several other metals, is attributed to the high degree of anisotropy in the linear compressibility of bismuth, resulting in shear stresses in the grain boundaries when it is exposed to hydrostatic pressure. Most thermally induced allotropic transformations in metals, whether of the diffusionless ather-ma1 (martensitic) or isothermal nucleation and growth types, are dependent upon structure and prior history,4 viz., grain boundaries, deformation, and so forth. One logically wonders then whether the transformation characteristics of the pressure-induced polymorphs in bismuth might also depend upon initial structure, particularly with respect to the presence of grain boundaries and associated plastic deformation. In this investigation, the role of grain boundaries and plastic deformation on the characteristics of the bismuth I-II and 11-111 transitions will be established. The rather unique residual microstruc-tural changes associated with these transitions will be presented and discussed. The occurrence of a measurable hysteresis in both the I-II and 11-111 transitions will be demonstrated. The type of transformation mechanism based on the observed transformation rate will be discussed. EXPERIMENTAL PROCEDURE A) Apparatus. The hydrostatic pressure system utilized in this investigation is similar to that previously reported by Bridgman' and Birch and Robertson,5 and has been previously described.3 For the purpose of this work, the pressure medium utilized was a 1:l mixture of pentane and isopentane. Pressure measurement was by means of a manganin coil in conjunction with a Foxboro Recorder. The manganin coil was mounted in the bottom closure and inserted inside the pressure cavity. Based on calibration against a controlled clearance piston gage at approximately 10,000 atm, the estimated error in the pressure measurement was +2 pct. Assuming the nonlinearity in the pressure coefficient of resistivity between 10,000 and 28,000 atm to be not greater than 1 pct, then the estimated error in the range of the I-II and 11-111 transitions was +3 pct. B) specimen Material and Preparation. The bismuth utilized throughout this investigation was of

Jan 1, 1964

By H. M. Chance

THE failure of the carbonic acid gas method at the Kehley Run Colliery has given rise to a conviction of the inefficienoy of the process; but a careful survey of the facts, and of the conditions under which it was tried, will show that a fair trial of the method was not and could not be made at this colliery; its failure in this particular instance therefore, should not be held as evidence against the process. In itself, the method seems to be theoretically perfect, but in prac-

Jan 1, 1881

By James Douglas

At this last meeting of our Institute for the year 1899, it is appropriate that we should look back at the past. To review the century's progress in the exact sciences and the resulting arts that fall within the scope of our labors is beyond my ability. But I wish to draw your attention to some phases of that progress, almost as important, which lie within the zone of sociology, touching at so many points the domain of applied technology. One of these is suggested by the library of technical literature which this century has produced —not the least important contribution to which is our own Transactions. The nineteenth century has witnessed the beneficial spread of democracy in politics. Under the impulse, to no small degree, of the same spirit, there has grown up a brotherhood of fellow-workers and a sense of fellow-ownership in the secrets of nature. Though the Patent Office has assumed such proportions as to hare become a source of national revenue, and a multitude of inventors, great and small, are seeking through its agency to secure some pecuniary profit from their devices, there is even greater eagerness among both interested and disinterested workers in the field of technology to publish their observations, and even their discoveries, and to give them to the world without remuneration. The motives influencing the great body of writers who, without any pay, use the technical journals and such media of communication as our Transactions, in order to give to the brethren of their craft the results of

Jan 1, 1900

By Lewis T. Wright

I have long been aware that ferruginous copper furnace-slags if fused in the electric arc will yield metallic iron containing copper, and in order to confirm this knowledge, and to obtain further information of the behavior of such slags in the high temperature and reducing conditions of the electric furnace, a number of samples of slag were fused in an experimental electric furnace. The results obtained, given in Table I., show that a very large amount of metallic iron was produced, and that this iron carried with it practically all the copper, gold, and silver, and more than 50 per cent. of the sulphur, of the original slag. The metallic buttons formed in the electric furnace were clean, hard, but not brittle.

Jan 1, 1911