Search Documents

By R. G. Aspden, D. A. Colling

THE {120}(001) texture has been reported in near 50 pct Ni-Fe alloys <0.004 in. thick1,2 and in copper 0.014 in. thick.3 This texture is one of two types of secondary recrystallization textures observed to replace a cube texture matrix and is desirable in Fe-Ni alloys because of its unique magnetic characteristics.1,2 However, the conditions for and mechanism of the {120}(001) formation are not well understood.3 During an investigation of the influence of alloying elements on the magnetic characteristics of 49 pct Ni-Fe alloys with a sheet thickness of 0.014 in., we have observed the growth of {120}(001) secondaries when strong deoxidizers such as aluminum and calcium were present. It is believed that this observation in unique and provides additional insight with regard to the mechanism for {120}(001) texture formation. Three alloys were prepared with electrolytic iron and nickel and contained a nominal 49 wt pct Ni. Alloy A was a straight binary Fe-Ni alloy, whereas intentional additions of 0.013 wt pct Ca to alloy B and of 0.59 wt pct A1 to alloy C were made. Ingots were forged at 1100 C, hot-rolled to 0.150 in. gage, pickled, and cold-rolled to 0.014 in. Standard U-shaped magnetic test specimens were punched, deburred, sprayed with MgO, and annealed in ~50°C dew point hydrogen. Textures were identified with the aid of etch pits, the

Jan 1, 1970

Uranium was the prima donna of 1978, and the exploration pace was fast and furious in traditional uranium producing areas such as the Powder River Basin, Grants mineral belt, San Juan Basin, and Uravan mineral belt. Adding fuel to the fire were several significant discoveries: The Date Creek Basin of western Arizona, the McDermitt caldera of northern Nevada, and Tallahassee Creek in Colorado&apos;s intermontane basin. Advances in solution mining haw resulted in deeper drilling on the Texas Coastal Plain, and the price of uranium has encouraged widespread exploration in frontier areas and non-sandstone environments.

Jan 5, 1979

By F. W. Jessen, C. C. Patton

Adsorbed films were formed on polished stainless steel specimens from dilute benzene solutions of two crude oil distillation residua. Although the two residua were extremely dissimilar in composition, contact angle measurements showed that the two films increased the wettability of the steel specimens to oil by equal amounts. Furthermore, the wettability of the films was essentially unaffected by the desorption techniques used. Paraffin deposits were formed from heptane-wax solutions on the same stainless steel specimens. These deposits definitely adhered to the surface. Presence of an adsorbed crude oil film on the metal surface increased its free surface energy and resulted in increased deposition of paraffin. The addition to the heptane - wax solution of small amounts of the same distillation residua that were used to form the adsorbed films resulted in decreased cohesive strength in the deposits formed, which resulted in decreased deposition. The presence of a crude oil fraction both in the solution and as a preadsorbed film eliminated the adherence of a deposit of any kind. A mechanism of deposition is proposed which explains the results obtained. INTRODUCTION The natural formation of any predominantly organic accumulation in oilwell tubing, surface flow lines or other production and storage facilities is called a paraffin deposit. These deposits restrict the production of crude oil, causing a substantial increase in production costs because of decreased flow capacity, expense for periodic deposit removal and unproductive downtime. The conditions under which such deposits form, their physical characteristics and the nature and severity of the problem created are extremely varied. Over the past several years, much progress has been made in developing and utilizing methods to remove accumulated paraffin deposition. However, like so many other problems, the basic stumbling block appears to be a lack of understanding of the fundamental mechanism involved in the formation of such deposits. Crude petroleum is known to contain considerable quantities of polar, surface active substances which Doddl has shown to be present at the oil-water interface. Denekas, Mattax and Davis2 observed that the wettability of reservoir rocks was drastically altered by exposure to crude oil fractions; and Zisman, et a1.3 showed that the nature of the compounds adsorbed on a surface would determine its wettability characteristics. Cole and Jessen4 and Ehrig5showed that surface wettability can have a profound effect on the magnitude of paraffin deposition, and Parks6 demonstrated chat the presence of certain adsorbed films on a metal surface would reduce the adherence of paraffin to that surface. Zisman7 has since advanced the theory that the conditions for adhesion are the same as for wetting. Therefore, it was felt that there was adequate evidence to support the supposition that adsorption of compounds from a crude oil might play an important part in paraffin deposition. ADSORPTION-WETTABILITY EXPERIMENTS Initial experiments were conducted to determine the effects of adsorption from solution of crude oil residua on the wettability of a polished stainless steel surface. Distillation residua with initial atmospheric boiling points of 700F were used in preference to the whole crudes in order to concentrate on the molecular weight range of interest, and to eliminate the possibility of composition change due to evaporation of the light ends. Also, these high boiling materials would be expected to be adsorbed from the whole oil in preference to similar compounds of lower molecular weight.

Jan 1, 1966

By K. Robert Dorman, F. Michael Jenkins

The occurrence of rock bursts in deep metal/nonmetal mines presents a major hazard to their safe and economical operation. As part of a Bureau of Mines program to reduce rock bursts in deep vein mining, a project was conducted in the Coeur d&apos;Alene Mining District of Idaho to evaluate and demonstrate the mining of a destressed sill pillar using undercut-and-fill methods. A 50-ft sill pillar in a burst-prone area was preconditioned by drilling and blasting vertical holes in the ore. After raises were driven through the destressed pillar to the level above, it was mined by the undercut-and-fill method. The conclusion from this demonstration is that the combination of ore preconditioning and underhand mining resulted in greatly improved rock burst and ground control, allowing safe and efficient mining of a potentially hazardous, burst-prone pillar.

Jan 1, 1984

By Herbert K. Kutter

This paper is concerned with the physical phenomena in the fracture process of presplitting and only indirectly with the establishment of the optimum presplitting parameters. Its nature is therefore qualitative, rather than quantitative.

Jan 1, 1968

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

By Kjell Lidin, Christer Nordström

INTRODUCTION LKAB produces iron ore in several mines in northern Sweden, and has been doing so for nearly 100 years. Total production to date is 600 million tonnes of finished products of various kinds (pellets, lump ore, fines). Close to 400 million tonnes have been produced by sublevel caving. This method has been the company&apos;s standard method for more than 20 years. A review of the development of equipment over the past 15 years and an outlook up to about 1990 leads to the following general re- flections concerning probable trends. Trends for all equipment are increasing precision and stricter environmental requirements will necessitate cabs, remote control etc to an increasing extent. Conventional sublevel caving can be broken down into the following unit operations: 1. Planning incl prospecting drilling. 2. Horizontal drilling. 3. Fan drilling. 4. Charging and blasting. 5. Loading and haulage at sublevels. 6. Ore drawing in chutes. 7. Rock reinforcement. 8. Production service. This lecture will deal in brief with each of these unit operations and the trends we are experiencing for them. A number of slides illustrating equipment

Jan 1, 1981

By R. E. Gilchrist, R. F. Nielsen

When a gas is displaced by mother in a porous medium, and there is a relative immobile liquid present. there is a transition zone in which the gas composition varies from essentially that of the original gas to that of the injected gas. The change in extent of this zone with time may be governed by a mixing process in the direction of flow and by the rate of establishment of gas-liquid equilibrium, if the gases are appreciably soluble in the liquid. The relative importance of these two factors in deterri~ining the growth of the transition zone is discussed, with appropriate equations and experimental data. INTRODUCTION The various solution methods of oil recovery involve a transfer of the components of a mixture, whether within a single phase or between a liquid and gas. The similarity of a natural porous medium to systems used in separation and chromatographic processes makes it seem reasonable that certain concepts used by chemical engineers in "mass transfer" might be applicable to petroleum reservoirs. One approach, the HETP (height equivalent to a theoretical plate), involves a distance or length of time over which equilibrium might be con. sidered as established. Another approach involves direct use of a rate of mixing or rate of establishment of equilibrium. The latter approach has been preferred in relation to production problems. DISCUSSION AND PROCEDURE When a gas or liquid in a porous medium is displaced by one of different composition but miscible with it there will be set up a transition zone in which the composition varies from cssentially that of the original fluid to essentially that of the injected fluid. If the fluid being displaced is a gas, and there is a relatively immobile liquid present, the transition zone may be

By A. B. Kinzel

ALTHOUGH calcium carbide and other compounds of calcium, as well as a number of calcium alloys, are well known and are the basis of important industries in the of United States, calcium metal has been thought of as something of a rarity and has received comparatively little attention from industrial metallurgists. The metal may he made in a number of ways, but the electrolytic deposition of calcium from a molten calcium chloride bath was the first process to be used for its commercial production and is still the standard procedure. Calcium metal has elicited little interest among nonferrous metal producers, as the demand has been relatively small and its production restricted to only a few plants, exclusively in France and Germany.

Jan 1, 1941

By W. L. Batt

MODERN war means mechanization, and mechanization means raw materials, especially minerals-and lots of them. Let me recall a few events of recent history-events that constitute mile- stones down the road to the war now blazing on three continents and threatening to spread still farther. In 1932, Japan took Manchuria, largely upon the excuse that she needed raw materials; in 1935, Italy invaded Ethiopia, largely upon the excuse that Mussolini&apos;s growing nation needed raw materials-in this case oil; from 1933 to 1935, Germany cried out for a greater share of the world&apos;s natural wealth, and since 1938 has invaded or occupied ten other countries, frequently upon the excuse that she needed-and had a right to-more raw materials.

Jan 1, 1940

By H. E. Lee, D. Ingvoldstad

AT Bunker Hill the original charge storage and preparation system was installed in 1917 to accommodate lead-silver gravity mill products. Only minor tonnages of wet fines such as vanner and flotation concentrates were received. Charge flux and diluent requirements were provided by an ample supply of siderite middlings and coarse lime-rock. While oversize material was crushed through %-in., the use of roll crushers in series resulted in a more or less granular, free-running charge of adequate porosity. Under such conditions, receipts could be proportioned directly from receiving bins, and suitable blending was obtained by passing the resultant layered composite through a small Stedman disintegrator. This elementary system served well for production and smelting of an extremely lead-rich sinter, in the low column blast furnace. Here sinter physical quality is less critical, and appreciable quantities of raw flux and oxidized ore may be charged directly to the blast furnace without seriously impairing furnace capacity. Prior to 1938 the relative proportions of zinc receipts were low and extraneous flux requirements at a minimum. However, subsequent war-inflated zinc demands brought marked increase in fine concentrate and slimy zinc leach residue receipts and an abrupt introduction to smelting a more refractory zinciferous charge. The higher temperature demands of the more refractory zinciferous charge required a higher smelting column and the higher column, in turn, rendered the blast furnace less receptive to improperly prepared feed. Inadequate presinter processing facilities prevented the production of acceptable sinter, and blast furnace production declined to 50 pct of former capacity. In view of a prevailing contention among lead metallurgists as to the deleterious action of high zinc slag on blast furnace capacity, it was natural to overstress this factor and to concentrate on possible changes in furnace design. Another interpretation was that primary correction should be sought through expanded sintering facilities. This divergence of opinion, together with the extreme material shortages of the 1940&apos;s, delayed corrective

Jan 1, 1957

By ALBERT F. J. BOARDEAUX

(Canal Zone Meeting, November. 191(j.) I. GENERAL INTRODUCTION. 1. Historical. ALLUVIAL gold was first discovered in Guiana in 1852, in the sands of the Arataye river; by Paulino, a Brazilian convict. During the following years, gold was found also in the rivers Orapu, Cirubé, etc. In 1873 the famous placers of the Sinnamary system were opened: Saint-Elie, Dieu-Merci, Adieu-Tat, and Couriége. This group of mines has produced nearly $10,000,000, according to official records, not including the gold that escaped the taxes. The discoverer was a mulatto named Vitalo. Except in a few rich spots, the gold was rather evenly distributed along the creeks. In one instance, gold was found in the red dirt from the slope of a hill, which, after transport to the creek, gave an amount of 150 kilograms. The placers of the Mana system, Enfin, Elysée, Pas-Trop-Tot, date from 1878, and their production has been about $5,000,000. In 1888, the Awa placers, along the boundary between the French and Dutch Guianas, on the Maroni and its tributaries, were discovered. They have yielded $12,000,000. The only industrial company,, the Dutch Guiana French Mining Co., produced in 15 years about 2,500 kg. of gold, worth $1,500,000. From 1893 dates the famous Carsewene discovery, in territory then in dispute between France and Brazil. A settlement was made recently in favor of Brazil, by arbitration of the Switzerland State Council. Carsewene is said to have pro-duced about $18,000,000 in six years (1894-1900), but not even one-fourth of the production went through French Guiana and

Nov 1, 1910

DEFENSE Materials Procurement Agency has been moving rapidly to encourage copper industry expansion programs. Although copper production is at a high level, a shortage exists on a world-wide basis as well as on the domestic scene. Projected expansion programs will not ease this current demand for most of them are 2 to 5 years off. Refining facilities are adequate but there is a shortage of ore and scrap, and it is for this reason that the expansion programs are directed at developing more sources of supply. The domestic expansion programmed thus far and understood to have been arranged with price escalation should the domestic price go to 271/20, were summarized by American Metal Markets as follows (dates of announcement are given in parenthesis: .1-Copper Cities Mining Co.&apos;s, $15,000,000 expansion near Miami, Ariz., to be operating about 1954. DMPA will buy 22,500 tons of copper a year up to a given amount on an agreed price of 23¢ per pound, with some exceptions and depending upon salability at a higher price to other purchasers in the U. S. (September 25th). 2-An RFC loan of $60,000 to North Butte Mining Co. to be paid off on the basis of deliveries at a purchase price of 241/20 per pound (September 25th). 3-A $25,000,000 expansion program by Phelps Dodge to provide 38,000 tons per year by late 1954. DMPA would purchase it at a price of 22¢ per pound up to 112,500 tons providing other purchasers in the U. S. will not pay a higher price (September 26th). 4-Anaconda Copper Mining Co. $40,000,000 expansion in Nevada to provide more than 30,000 (might be increased to 45,000) tons per year. DMPA would purchase the copper at 250 per pound for a limited period of time if it is not salable to industrial users at above this price. Production would start around 1953 (November 14th).

Jan 1, 1952

By Jennings S. Cox

(Glen Summit Meeting, June, 1911.) THE following notes, prepared in 1908, as the result of a personal examination and extensive explorations under my direction in 1906, have been revised and greatly augmented after two subsequent visits and further explorations in 191.0. The hard iron-ores of the south coast of Oriente Province, in the island of Cuba, have been known for many years, in fact one mine has been in operation for more than 20 years ; but it is only within the past four years that the large mantle-deposits of brown ores of the north coast have attracted serious attention. A. C. Spencer 1 has described these ores in a paper, entitled Three Deposits of Iron Ore in Cuba, which refers to the Mayari, Moa, and Cubitas deposits. C. M. Weld,2 in a scholarly paper on The Residual Brown Iron-Ores of Cuba, has discussed the character and possible genesis of these deposits with particular reference to the Moa field, calling attention also to the Taco and Navas fields in addition to those described by Spencer. Descriptive articles with reference to the Mayari field, and a few words about the Moa deposit, have also appeared.3 It is the purpose of the present paper to give some account of the exploration of the Moa deposit and to call attention to its commercial importance. LOCATION. The Moa district is situated on the north coast of the . Province of Oriente, which is the most easterly province of the island of Cuba. It lies on the northern or seaward slope of 1 Bulletin No. 340, U. S. Geological Survey, pp. 318 to 329 (1908). 2 Trans., xl., 299 to 312 (1910). 3 Iron Age, vol. lxxx., No. 7, pp. 421 to 426 (Aug. 15, 1907), and vol. lxxxi., No. 15, pp. 1149 to 1157 (April 9, 1908).

Mar 1, 1911

By GILBERT E. SEIL

GREAT advances in the preparation of ores for reduction to ferro-alloys have been made, although standard methods of reduction have been continued at most plants. Efficiencies, yields per furnace, and energy requirements per ton are generally better than previously attained. The advantages of sizing and conditioning of ore, fluxing stone, and coke have been realized. Conditioning varies from drying the furnace burden to chemical rearrangements to facilitate reduction reactions and sometimes to furnish some of the energy required for the reaction before the burden reaches the furnace. During the war period it is impossible to discuss in detail many of the advances made. They are subjects for postwar papers. However, the new procedures mentioned in the following paragraphs are indicative of the work already done and in progress.

Jan 1, 1944

By A. E. Himebaugh

A SEMI-AUTOMATIC hoist has been installed at the 2966 station of the Copper Queen mine, since neither the bulk of supplies handled nor the number of men engaged in developing the 3100 level justifies the constant attendance of two cagers and two hoist operators. The connecting service shaft between the 2966 and 3100 levels is actually a two-compartment raise. Below the 2966 level the shaft is 7x13 ft-slightly oversize to permit downcast ventilation and provide space for the 16-conductor flexible control cable. The raise extends 52 ft above the 2966 level for a 3-ft diam head sheave. Another 3-ft sheave is mounted as an idler between the hoist and head sheave, eliminating the need for an inclined cableway. The main compartment serves as a cageway; the other compartment provides a manway and space for service lines. Since vertical travel is limited, rope speed is of minor importance.

Jan 5, 1958

By R. W. Diamond

Low-grade ores can be designated by two main classifications: (1) simple low-grade ores, and (2) complex low-grade ores. As a rule the first type has a relatively small metal content, although low- grade iron ores contain a rather high percentage of metal. As the simple type is the one that is ordinarily in mind when the term "low-grade ore" is used, the paper will be devoted mainly to ores in this general category. Cheap treatment is the prime requirement in utilizing low-grade ores of the simple type, although in some cases the value of nonmetallic by-products, such as limestone for fer- tilizer and silica for flux, allows a little more lati- tude than in the usual situation. When the costs are divided under the three headings-mining, milling, and smelting-it is apparent that the last group will not constitute an important factor as a rule because the high concentrating ratio makes the smelting cost per ton of ore fairly low.

Jan 1, 1949

By J. R. Campbell

It is the purpose of this paper to review somewhat in detail the literature on the subject that is extant, which ought to provoke considerable beneficial discussion. The value of 1 per cent. ash in blast-furnace practice was brought to the attention of the writer when he was connected with the U. S. Steel Corpn. Various groups of blast furnaces in the Pittsburgh district compiled a statement in which the average saving was about 6 c. per ton on pig iron for every 1 per cent. of ash reduction. Later, the same groups of furnaces, when materials had reached a higher price, compiled a statement in which there was a 30-cent saving on pig iron for every 4 per cent. ash reduction in the Pittsburgh district, which was equivalent to 7½ c. for every 1 per cent. ash reduction. In the Chicago district, on long freight hauls of coal and coke from the Pocahontas district, the set-up was 30 c. per ton of pig iron for every 2 per cent. ash reduction, or 15 c. for every 1 per cent. Some years ago, Ralph H. Sweetser, of the American Rolling Mill Co., presented a paper which provoked considerable comment.&apos; To get the matter again before this body a résumé of his computations is given below: Comparison of Pig Iron Costs Ash in Coal. Ash in CoKe, Fixed Carbon in Coke peR Ton OB PIG Iron peN Day, Per Cent. PeR CeNt. Coke. Per Cent. PIG IRon. Lb. Tons 6.00 8.70 89.80 1800 365.0 7.00 10.15 88.35 1860 353.2 Coke with 8.70 Per Cent. Ash Ore mixture, 4144 It). = 1.85 tons @ $5.50.............................. $10.17 Coke, 1800 lb. = 0.90 ton @ $6.50..................................... 5.85 Limestone, 1000 lb. = 0.50 ton @ $1.50................................. 0.75 Labor, $365 per day on 365 tons....................................... 1.00 Supplies and service, $250 per day...................................... 0.68 Overhead, $200 per day............................................... 0.55 Reserve for relining and depreciation................................... 1.00 Total............................................................. $20.00

Jan 1, 1931

By Richard D. Snouffer

Prime topics of conversation these days are the new concepts of rail haulage for bulk items such as iron ore, potash and coal. We have heard such ideas as the "integral train" and the "unit train" discussed frequently during the past two years at various AIME meetings, and progress reports have kept up a steady appearance in the technical press and in local newspapers. While no railroad has a complete "unit train" in service at this moment, one has 50 fast-discharge cars under construction and the Pennsylvania Railroad has experimented with radio-controlled motive power distributed at intervals throughout the train. To a great extent, however, the promise for greater efficiency and lower costs held out to industry by these new haulage methods is dependent not on greater speed or larger cars or more dedicated equipment alone but, rather, on the utilization of modern practices in the loading and unloading of rail cars. It is the purpose here to examine these two key steps and the up-to-date procedures and equipment they entail.

Jan 7, 1963

By A. H. Bell

DEEPEST hole in the earth, and deepest producing oil well in the world-such is well No. K.C.L. A-2, of the Continental. Oil Co., completed on April 12 in the San Joaquin valley about four miles west of Wasco, Calif. It penetrated the earth&apos;s crust to a depth of 15,004 ft.- almost three miles-a depth that exceeds by over 2200 ft. that of the previous record holder in western Texas. It is now producing oil from sands at a depth from 13,092 to 13,- 175 ft., which is about 1500 ft. deeper than the record formerly achieved in Louisiana. Continental&apos;s new well was bottomed in what is possibly Domengine-Avenal Eocene sand, and is producing from the Middle Miocene equivalent to the Rio Bravo sand.

Jan 1, 1938